The vcc3v3-btreg regulator only has 1 state and no state gpios defined,
so "regulator-gpio" is not the correct binding to use. "regulator-fixed"
is the correct binding to use. It supports an enable GPIO which is
needed in this case.
Signed-off-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20250409205047.1522943-1-robh@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The recommended name for enable GPIOs property in regulator-gpio is
enable-gpios. This is also required by bindings:
px30-engicam-px30-core-ctouch2.dtb: vcc3v3-btreg: Unevaluated properties are not allowed ('enable-gpio' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230725142616.157405-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Engicam PX30 carrier boards like EDIMM2.2 and C.TOUCH2.0 have
an onboard Sterling-LWD Wifi/BT chip based on BCM43430 connected
on the UART bus.
UART bus on the design routed via USB to UART CP20x bridge. This
bridge powered from 3V3 regualtor gpio.
This patch adds BT enablement nodes for these respective boards.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20201109181017.206834-7-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Engicam PX30 carrier boards like EDIMM2.2 and C.TOUCH2.0 have
an onboard Sterling-LWD Wifi/BT chip based on BCM43430 connected
on the SDIO bus.
The SDIO power sequnce is connacted with exteernal 32KHz oscillator
and it require 3V3 regulator input.
This patch adds WiFi enablement nodes for these respective boards.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20201109181017.206834-6-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Engicam C.TOUCH 2.0 is an EDIMM compliant general purpose
carrier board with capacitive touch interface.
Genaral features:
- TFT 10.1" industrial, 1280x800 LVDS display
- Ethernet 10/100
- Wifi/BT
- USB Type A/OTG
- Audio Out
- CAN
- LVDS panel connector
SOM's like PX30.Core needs to mount on top of this Carrier board
for creating complete PX30.Core C.TOUCH 2.0 board.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200929083217.25406-7-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
