Cool Pi CM5 GenBook works as a carrier board connect with CM5 [0].
Specification:
- Rockchip RK3588
- LPDDR5X 8/32 GB
- eMMC 64 GB
- HDMI Type A out x 1
- USB 3.0 Host x 1
- USB-C 3.0 with DisplayPort AltMode
- PCIE M.2 E Key for RTL8852BE Wireless connection
- PCIE M.2 M Key for NVME connection
- eDP panel with 1920x1080
This patch add basic support to bringup eMMC/USB HOST/WiFi/TouchPad/
Battery/PCIE NVME, and can also drive a HDMI output with out of tree
hdmi patches.
[0] https://www.crowdsupply.com/shenzhen-tianmao-technology-co-ltd/genbook-rk3588
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20240730102433.540260-3-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Xunlong Orange Pi 3B is a single-board computer based on the
Rockchip RK3566 SoC.
Add initial support for eMMC, SD-card, Ethernet, HDMI, PCIe and USB.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240626230319.1425316-3-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Radxa ROCK 3B is a single-board computer based on the Pico-ITX form
factor (100mm x 75mm). Two versions of the ROCK 3B exists, a community
version based on the RK3568 SoC and an industrial version based on the
RK3568J SoC.
Add initial support for eMMC, SD-card, Ethernet, HDMI, PCIe and USB.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240627211737.1985549-3-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The ROCK 5 ITX as the name suggests is made in the ITX form factor and
actually built in a form to be used in a regular case even providing
connectors for regular front-panel io.
It can be powered either by 12V, ATX power-supply or PoE.
Notable peripherals are the 4 SATA ports, M.2 M-Key slot, M.2 E-key slot,
2*2.5Gb PCIe-connected Ethernet NICs.
As of yet unsupported display options consist of 2*HDMI, DP via USB-c,
eDP + 2*DSI via PCB connectors.
USB ports are 4*USB3 + 2*USB2 on the back panel and 2-port front-panel
connector.
Schematics for the board can be found on
- https://dl.radxa.com/rock5/5itx/radxa_rock_5_itx_X1100_schematic.pdf
- https://dl.radxa.com/rock5/5itx/v1110/radxa_rock_5itx_v1110_schematic.pdf
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240704153815.837392-3-heiko@sntech.de
Add rock5b overlays for PCIe endpoint mode support.
If using the rock5b as an endpoint against a normal PC, only the
rk3588-rock-5b-pcie-ep.dtbo needs to be applied.
If using two rock5b:s, with one board as EP and the other board as RC,
rk3588-rock-5b-pcie-ep.dtbo and rk3588-rock-5b-pcie-srns.dtbo has to
be applied to the respective boards.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20240607-rockchip-pcie-ep-v1-v5-13-0a042d6b0049@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The CM3588 NAS by FriendlyElec pairs the CM3588 compute module, based on
the Rockchip RK3588 SoC, with the CM3588 NAS Kit carrier board.
To reflect the hardware setup, add device tree sources for the SoM and
the NAS daughter board as separate files.
Hardware features:
- Rockchip RK3588 SoC
- 4GB/8GB/16GB LPDDR4x RAM
- 64GB eMMC
- MicroSD card slot
- 1x RTL8125B 2.5G Ethernet
- 4x M.2 M-Key with PCIe 3.0 x1 (via bifurcation) for NVMe SSDs
- 2x USB 3.0 (USB 3.1 Gen1) Type-A, 1x USB 2.0 Type-A
- 1x USB 3.0 Type-C with DP AltMode support
- 2x HDMI 2.1 out, 1x HDMI in
- MIPI-CSI Connector, MIPI-DSI Connector
- 40-pin GPIO header
- 4 buttons: power, reset, recovery, MASK, user button
- 3.5mm Headphone out, 2.0mm PH-2A Mic in
- 5V Fan connector, PWM beeper, IR receiver, RTC battery connector
PCIe bifurcation is used to handle all four M.2 sockets at PCIe 3.0 x1
speed. Data lane mapping in the DT is done like described in commit
f8020dfb31 ("phy: rockchip-snps-pcie3: fix bifurcation on rk3588").
This device tree includes support for eMMC, SD card, ethernet, all USB2
and USB3 ports, all four M.2 slots, GPU, beeper, IR, RTC, UART debugging
as well as the buttons and LEDs.
The GPIOs are labeled according to the schematics.
Reviewed-by: Space Meyer <git@the-space.agency>
Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de>
Link: https://lore.kernel.org/r/20240616215354.40999-3-seb-dev@mail.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Radxa ROCK S0 is a single-board computer based on the Rockchip RK3308B
SoC in an ultra-compact form factor.
Add initial support for eMMC, SD-card, Ethernet, WiFi/BT and USB.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240521212247.1240226-3-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Radxa ZERO 3W/3E is an ultra-small, high-performance single board
computer based on the Rockchip RK3566, with a compact form factor and
rich interfaces.
The ZERO 3W and ZERO 3E are basically the same size and model, but
differ only in storage and network interfaces.
- eMMC (3W)
- SD-card (both)
- Ethernet (3E)
- WiFi/BT (3W)
Add initial support for eMMC, SD-card, Ethernet, HDMI and USB.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240521202810.1225636-3-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Radxa ROCK 3C is a development board with the
Rockchip RK3566 SoC. It has the following features:
- 1/2/4GB LPDDR4
- 1x HDMI Type A
- 1x PCIE 2.0 slot
- 1x FAN connector
- 3.5mm jack with mic
- 1GbE RTL8211F Ethernet
- 1x USB 3.0, 3x USB 2.0
- 40-pin expansion header
- MicroSD card/eMMC socket
- 16MB SPI NOR (gd25lq128d)
- AP6256 or AIC8800 WiFi/BT
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://lore.kernel.org/r/20240428123618.72170-3-amadeus@jmu.edu.cn
[dropped rk809-sound and not specified pmic sound properties]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the GameForce Chi, which is a handheld gaming console
from GameForce with a Rockchip RK3326 SoC. The device has a 640x480
3.5" dual-lane DSI display, one analog joystick connected to the SoC
SARADC controller and a second analog joystick connected to an unknown
UART based ADC, a single SD card slot, a single USB-C port for
charging, and onboard RTL8723BS WiFi/Bluetooth combo, multiple face
buttons, and an array of R/G/B LEDs used for key backlighting.
The vendor was unable to provide details on the unknown UART based
ADC which I have documented via a comment in the device-tree, and
the vendor also does not have available Bluetooth firmware (the BT
was not previously working on the vendor's OS, this has also been
noted in a device-tree comment).
Aside from the right analog ADC joystick and bluetooth all hardware has
been tested and is working as expected.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240325134959.11807-6-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
MECSBC is a single board computer for blood analysis machines from
RR-Mechatronics, designed and manufactured by Protonic Holland, based on
the Rockchip RK3568 SoC.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240405-protonic-mecsbc-v2-2-0a6fedc78b9f@pengutronix.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add device tree overlay for the WolfVision PF5 IO Expander board. This
extension board can be attached to the WolfVision PF5 mainboard and
features
- TI DP83826 Ethernet PHY
- RJ45 jack
- USB-A host port
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-feature-wolfvision-pf5-v1-4-5725445f792a@wolfvision.net
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add device tree for the WolfVision PF5 mainboard. It features
- Rockchip RK3568 SoC
- eMMC
- RTC with backup battery
- on-board PDM microphone
- 12V DC jack
- HDMI output
- USB-C device port
as well as various expansion headers for different extension boards.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-feature-wolfvision-pf5-v1-3-5725445f792a@wolfvision.net
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Haikou is a Qseven and μQseven baseboard featuring PCIe, USB3 and a
video connector for a MIPI-DSI/CSI adapter.
This dts is for usage with the RK3588-Q7 SoM Tiger.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240227164659.705271-5-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the Powkiddy RGB10MAX3. The Powkiddy RGB10MAX3 is a
handheld gaming device with a 720p 5.0 inch screen powered by the
Rockchip RK3566 SoC. It includes a Realtek 8723ds WiFi/BT module, 2 ADC
joysticks powered by a 4-way muxed ADC channel, and several GPIO
face buttons. There are 2 SDMMC slots (sdmmc1 and sdmmc3), 3 pwm
controlled LEDs, and the device includes 1GB of RAM.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240212184950.52210-8-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This includes support for both the v0.1 units that were sent to developers and
the v2.0 units from production.
v1.0 is not included as no units are known to exist.
Working/Tested:
- SDMMC
- UART
- Buttons
- Charging/Battery/PMIC
- Audio
- USB
- Display
- SPI NOR Flash
Signed-off-by: Alexander Warnecke <awarnecke002@hotmail.com>
Signed-off-by: Manuel Traut <manut@mecka.net>
Tested-By: Diederik de Haas <didi.debian@cknow.org>
Reviewed-by: Ondrej Jirman <megi@xff.cz>
Tested-by: Ondrej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20240127-pinetab2-v4-4-37aab1c39194@mecka.net
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Edgeble NCM6A SOM has on-module M.2 1216-compatible WiFi modules.
Currently, AW-XM548NF WiFi6 and Intel 8260D2W WiFi5 modules are supported.
WiFi modules are fixed on SoM, not pluggable M.2 slots, so different SoM's
for each type of WiFi module.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20231125190522.87607-5-jagan@edgeble.ai
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the Anbernic RG-ARC S and RG-ARC D devices. These
devices feature the following:
- Rockchip RK3566 SoC
- 4 inch 480x640 display (rotated)
- Goodix multi-touch (ARC D only, untested as I lack the device)
- 1GB (ARC S) or 2GB (ARC D) of RAM
- 2 SDMMC slots
- eMMC (ARC D only)
- Realtek 8821CS WiFi/Bluetooth
- External stereo speakers
- 6 face buttons (A, B, C, X, Y, Z) along with a D-Pad and start and
select buttons.
- A PWM vibrator.
Note that the Goodix touchscreen on I2C2 is not defined, as I lack
the necessary hardware to confirm it works correctly with the mainline
driver.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240123212111.202146-5-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Cool Pi CM5 EVB works as a mother board connect with CM5.
CM5 Specification:
- Rockchip RK3588
- LPDDR4 2/4/8/16 GB
- TF scard slot
- eMMC 8/32/64/128 GB module
- Gigabit ethernet x 1 with PHY YT8531
- Gigabit ethernet x 1 drived by PCIE with YT6801S
CM5 EVB Specification:
- HDMI Type A out x 2
- HDMI Type D in x 1
- USB 2.0 Host x 2
- USB 3.0 OTG x 1
- USB 3.0 Host x 1
- PCIE M.2 E Key for Wireless connection
- PCIE M.2 M Key for NVME connection
- 40 pin header
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20231212124407.1897604-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
CoolPi 4B is a rk3588s based SBC.
Specification:
- Rockchip RK3588S
- LPDDR4 2/4/8/16 GB
- TF scard slot
- eMMC 8/32/64/128 GB module
- Gigabit ethernet drived by PCIE with RTL8111HS
- HDMI Type D out
- Mini DP out
- USB 2.0 Host x 2
- USB 3.0 OTG x 1
- USB 3.0 Host x 1
- WIFI/BT module AIC8800
- 40 pin header
Signed-off-by: Andy Yan <andyshrk@163.com>
arm64: dts: rockchip: Add support for rk3588s based board Cool Pi 4B
Link: https://lore.kernel.org/r/20231212124253.1897438-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the Anbernic RG351V, which is a handheld gaming console
from Anbernic with an RK3326 SoC, a 640x480 LCD display, a single
analog joystick with several face buttons, two USB C ports, and
internal WiFi over USB. All hardware has been tested as working
except for the battery, which will require further modification to the
mainline rk817 battery driver before it can be used (the device was
built without a shunt resistor, and as such the battery cannot
measure current; only voltage).
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20231120230131.57705-4-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the Powkiddy X55. The Powkiddy X55 is a handheld
gaming device with a 720p 5.5 inch screen powered by the Rockchip
RK3566 SoC. It includes a Realtek 8821cs WiFi/BT module, 2 ADC
joysticks powered by 4 dedicated ADC channels, and several GPIO
face buttons. There are 2 SDMMC slots (sdmmc1 and sdmmc3), and an
8GB internal eMMC.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20231204185719.569021-11-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the Powkiddy RK2023. The Powkiddy RK2023 is a handheld
gaming device with a 3.5 inch screen powered by the Rockchip RK3566
SoC. The device looks physically different from the Powkiddy RGB30,
but is functionally identical except for the panel.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20231117202536.1387815-7-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Turing RK1 is an upcoming RK3588-based SoM from Turing Machines,
designed on the Jetson SO-DIMM form factor and meant to be compatible
with most Jetson carrier boards (but especially the Turing Pi 2 cluster
board from the same vendor). It has the typical I/O you'd expect from
a Jetson board, including:
- Two UARTs (UART9 for console, UART2 is auxiliary)
- PCI Express (2.0 x1 + 3.0 x4)
- Gigabit Ethernet
- On-board eMMC
- PWM fan w/ tach
- USB-OTG [1]
- HDMI and MIPI DSI [1]
- Miscellaneous external GPIO, I²C, SPI lines [1]
Beyond that, it is pretty similar to the RK3588 EVB (in terms of PMICs,
RTC, etc).
While this is absolutely a SoM, it is a little bit special in that it's
marketed directly to users as a compute node, while most SoMs are
intended to be a part/module incorporated into a larger system. Because
of this, a majority of the users will be treating the RK1 less like a
SoM and more like a miniature "blade server."
This patch introduces a dtsi to enable most[1] of the SoM I/O, as well
as a dts catered more directly to the "compute node" use case.
[1] These peripherals are not addressed with this patch.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Link: https://lore.kernel.org/r/20231011225823.2542262-4-CFSworks@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Powkiddy RGB30 is a portable game device based on the Rockchip
RK3566 SoC. It has GPIO buttons on the face and sides for input, stereo
speakers, a 720x720 4 inch DSI display, a USB-C host port and a USB-C
peripheral port, dual SD card slots, WiFi, Bluetooth, and 1GB of RAM.
Working/Tested:
- SDMMC
- UART (for debugging)
- Buttons
- Charging/battery/PMIC
- Speaker/Headphones
- USB
- WiFi
- Bluetooth
- Display (at 59.04hz)
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20231013183918.225666-6-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Orange Pi 5 Plus is RK3588 based SBC featuring:
- 2x 2.5G ethernet ports – onboard NIC hooked to PCIe 2.0 interface
- 2x USB 2.0 host ports
- 2x USB 3.0 host ports (exposed over USB 3.0 hub)
- Type-C port featuring USB 2.0/3.0 and Alt-DP mode
- PCIe 2.0/USB 2.0/I2S/I2C/UART on E.KEY socket
- RTC
- ES8388 on-board sound codec – jack in/out, onboard mic, speaker amplifier
- SPI NOR flash
- RGB LED (R is always on)
- IR receiver
- PCIe 3.0 on the bottom for NVMe, etc.
- 40pin GPIO header (with gpio, I2C, SPI, PWM, UART)
- Power, recovery and Mask ROM buttons
- 2x HDMI out, 1x HDMI in
- Slots/connectors for eMMC, uSD card, fan, MIPI CSI/DSI
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20231008130515.1155664-5-megi@xff.cz
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the NanoPC T6, a single board computer from FriendlyElec based on
the RK3588.
Initial device tree supports debug UART, SD, eMMC, PCIe 3, PMIC,
and 40 pin GPIO assignments.
Signed-off-by: Thomas McKahan <tmckahan@singleboardsolutions.com>
Link: https://lore.kernel.org/r/20230809112120.99-3-tmckahan@singleboardsolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add board-specific devicetree file for the RK3399T-based Radxa ROCK 4SE
board. This board offers similar peripherals in a similar form-factor to
the existing ROCK Pi 4B but uses the cost-optimised RK3399T processor
(which has different OPP table than the RK3399) and other minimal hardware
changes.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Link: https://lore.kernel.org/r/20230710115025.507439-4-chris.obbard@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Indiedroid Nova is an SBC from a sub-brand of Ameridroid that
includes the following hardware:
- A 40-pin GPIO header
- 2 USB-A 3.0 ports
- 2 USB-A 2.0 ports
- A USB-C 2.0 OTG port (used for USB power delivery)
- A USB-C 3.0 port that can do display port output.
- A Micro HDMI 2.1 port.
- A 1GB ethernet port.
- An RT8821CS based WiFi/Bluetooth module.
- A user replaceable eMMC module.
- An SDMMC card slot.
- A MIPI DSI connector.
- A MIPI CSI connector.
- A 3.5mm TRRS audio jack with microphone input.
- An 2 pin socket for an RTC battery.
- A 4 pin socket for a debug port.
- A power button (connected to PMIC), a reset button (connected to SoC
reset), a boot button, and a recovery button (both connected to the
ADC).
- 4GB, 8GB, or 16GB of system RAM.
This initial devicetree includes support for the WiFi, bluetooth,
analog audio out/in, SDMMC, eMMC, RTC, UART debugging, and has
the regulator values from the schematics. ADC, graphics output, GPU,
USB, and wired ethernet are still pending additional upstream changes.
Analog audio will require changes to handle a difference between the
requested clock frequency of 12288000 and the actual clock freqency
of 12287999 before it will work properly. This will be done in a
subsequent patch series.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20230531161220.280744-6-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Neural Compute Module 6B(Neu6B) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
IO board offers plenty of peripherals and connectivity options and
this patch enables basic eMMC and UART which is enough to successfully
boot Linux.
General features:
- microSD slot
- 1x HDMI Out
- 1x HDMI In
- 2x DP
- 1x eDP
- 2x MIPI DSI connector
- 4x MIPI CSI2 connector
- 2x USB Host
- 2x USB 3.0 OTG/Host
- 1x SATA
- 1x 2.5Gbps Ethernet
- 1x 4G/5G mini PCIe
- 1x M.2 E-Key slot
- 1x Onboard PoE
- 1x RS485, RS232, CAN
- 1x Audio, MIC port
- RTC battery slot
- 40-pin GPIO expansion
Neu6B needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6B(Neu6B) IO platform.
Add support for Edgeble Neu6 Model B IO Board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230516163454.997736-4-jagan@edgeble.ai
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The NanoPi R2C Plus is a small variant of NanoPi R2C with a on-board
eMMC flash (8G) included.
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Link: https://lore.kernel.org/r/20230513135307.26554-2-cnsztl@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the Anbernic RG353PS. This device is identical in form
factor to the RG353P and has the following hardware differences:
- No touchscreen is present on i2c2 (or at all).
- Only contains 1GB of RAM.
- Has no eMMC.
- Only appears to ship with the 2nd revision of the display panel.
Note that the display panel has been added to the st7703 panel driver
in a separate commit series.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20230512162039.31132-3-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The OrangePi R1 Plus LTS is a minor variant of OrangePi R1 Plus with
the on-board NIC chip changed from rtl8211e to yt8531c, and otherwise
identical to OrangePi R1 Plus.
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Link: https://lore.kernel.org/r/20230325074022.9818-5-cnsztl@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The NanoPi R2C is a minor variant of NanoPi R2S with the on-board NIC
chip changed from rtl8211e to yt8521s, and otherwise identical to R2S.
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Link: https://lore.kernel.org/r/20230325074022.9818-3-cnsztl@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Edge2 is an ultraslim, credit-card sized ARM PC designed by Khadas.
In this patch, we will add basic device tree support for this board,
Only eMMC, UART are enabled, so it's capable of booting into
a basic linux system from eMMC via serial console.
Signed-off-by: Yixun Lan <dlan@gentoo.org>
Link: https://lore.kernel.org/r/20230315033441.32719-3-dlan@gentoo.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Radxa Compute Module 3(CM3) IO board is an application board from Radxa
and is compatible with Raspberry Pi CM4 IO form factor.
Specification:
- 1x HDMI,
- 2x MIPI DSI
- 2x MIPI CSI2
- 1x eDP
- 1x PCIe card
- 2x SATA
- 2x USB 2.0 Host
- 1x USB 3.0
- 1x USB 2.0 OTG
- Phone jack
- microSD slot
- 40-pin GPIO expansion header
- 12V DC
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Add support for Radxa CM3 IO Board.
Co-developed-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Co-developed-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20230112105902.192852-3-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Neural Compute Module 6(Neu6) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
IO board offers plenty of peripherals and connectivity options and
this patch enables basic eMMC and UART which is enough to successfully
boot Linux.
Neu6 needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6(Neu6) IO platform.
Add support for Edgeble Neu6 Model A IO Board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230110134658.820691-3-jagan@edgeble.ai
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add board file for the RK3588 Rock 5B board. This is a basic
implementation which just brings up the eMMC and UART which is
enough to successfully boot Linux.
The ethernet controller is connected via PCIe so support will
come in a follow-up patch.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230109155801.51642-8-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add board file for the RK3588s Rock 5A board. While the hardware
offers plenty of peripherals and connectivity this basic implementation
just handles things required to access eMMC, UART and Ethernet (i.e.
enough to successfully boot Linux).
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Tested-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230109155801.51642-7-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add board file for the RK3588 evaluation board. While the hardware
offers plenty of peripherals and connectivity this basic implementation
just handles things required to successfully boot Linux from eMMC,
connect via UART or Ethernet.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[rebase, update commit message, use EVB1 for SoC bringup]
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20230109155801.51642-6-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.
This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://lore.kernel.org/r/20221203074149.11543-3-amadeus@jmu.edu.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
LubanCat 2 is a rk3568 based SBC from EmbedFire.
Specification:
- Rockchip rk3568
- LPDDR4/4X 1/2/4/8 GB
- TF scard slot
- eMMC 8/32/64/128 GB
- Gigabit ethernet x 2
- HDMI out
- USB 2.0 Host x 1
- USB 2.0 Type-C OTG x 1
- USB 3.0 Host x 1
- Mini PCIE interface for WIFI/BT module
- M.2 key for 2280 NVME
- 40 pin header
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20230108110817.2214859-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The LubanCat 1 is a RK3566 based SBC, developed by Dongguan EmbedFire
Electronic Technology Co., Ltd.
It has the following characteristics:
- MicroSD card slot, onboard eMMC flash memory
- 1GbE Realtek RTL8211F Ethernet Transceiver
- 1 USB Type-C port (power and USB2.0 OTG)
- 1 USB 3.0 Host port
- 3 USB 2.0 Host ports
- 1 HDMI
- 1 infrared receiver
- 1 MIPI DSI
- 1 MIPI CSI
- 1 x 4-section headphone jack
- Mini PCIe socket (USB or PCIe)
- 1 SIM Card slot
- 1 SYS LED and 1 PWR LED
- 40-pin GPIO expansion header
Signed-off-by: Wenhao Cui <lasstp5011@gmail.com>
Signed-off-by: Yuteng Zhong <zonyitoo@gmail.com>
Link: https://lore.kernel.org/r/Y6UdjhBD/Xa7ALya@VM-66-53-centos
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Radxa E25 is a network application carrier board for the Radxa CM3
Industrial (CM3I) SoM, which is based on the Rockchip RK3568 SoC.
It has the following features:
- MicroSD card socket, on board eMMC flash
- 2x 2.5GbE Realtek RTL8125B Ethernet transceiver
- 1x USB Type-C port (Power and Serial console)
- 1x USB 3.0 OTG port
- mini PCIe socket (USB or PCIe)
- ngff PCIe socket (USB or SATA)
- 1x User LED and 16x RGB LEDs
- 26-pin expansion header
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://lore.kernel.org/r/20221209102524.129367-3-amadeus@jmu.edu.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds the device tree for the "Model A" baseboard for
the SOQuartz CM4 SoM, which is not to be confused with the
Quartz64 Model A, which is the same form factor and SoC, but is
not a CM4 carrier board.
The board features a PCIe 2 x1 slot, USB 2 host ports, CSI/DSI
connectors, an eDP FFC connector, gigabit ethernet, HDMI, and a
12V DC barrel jack. Also present is a microSD card slot, 40-pin
GPIO, and a power and reset button.
Signed-off-by: Andrew Powers-Holmes <aholmes@omnom.net>
[rebase, misc fixes, reword]
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Link: https://lore.kernel.org/r/20221116115337.541601-5-frattaroli.nicolas@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds a device tree for the PINE64 SOQuartz blade baseboard,
a 1U rack mountable baseboard for the CM4 form factor with PoE
support designed for the SOQuartz CM4 System-on-Module.
The board takes power from either PoE or a 5V DC input, and allows
for mounting an M.2 SSD.
The board also features one USB 2.0 host port, one HDMI output,
a 3.5mm jack for UART, and the aforementioned gigabit networking
port.
Signed-off-by: Andrew Powers-Holmes <aholmes@omnom.net>
[rebase, squash, reword, misc fixes]
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Link: https://lore.kernel.org/r/20221116115337.541601-3-frattaroli.nicolas@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This device is a clone of Odroid Go Advance, with added PWM motor, internal
gamepad connected on USB instead of just having it be on GPIO + ADC, and
missing battery shunt resistor.
Due to missing shunt resistor and lack of a workaround in rk817_charger
driver rk817_charger is not enabled in dts.
There's also an LED on GPIO 77(I *guess* PB5 on &gpio2),
that is controlled in a weird way:
- It is set to red by setting output value to 1
- Set to green by setting output value to 0
- Set to yellow by setting gpio direction to input
I have no idea how to describe that in DTS, without adding a custom
driver, for now it's just left out.
Signed-off-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Link: https://lore.kernel.org/r/20221117215954.4114202-6-maccraft123mc@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This device is another revision of Odroid Go Advance, with added two
volume buttons, a second analog stick and a bigger screen that isn't yet
supported in the mainline kernel.
Signed-off-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Link: https://lore.kernel.org/r/20221117215954.4114202-5-maccraft123mc@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is a rk3566 tv box evaluation demo board.
Specification:
- Rockchip RK3566
- DDR4 4GB
- TF sd scard slot
- eMMC
- AP6398S for WiFi + BT
- Gigabit ethernet
- HDMI out
- USB HOST 2.0 x 2
- USB 3.0 x 1
- USB OTG 2.0 x 1
- 12V DC Power supply
Signed-off-by: Piotr Oniszczuk <piotr.oniszczuk@gmail.com>
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20221105100012.958252-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Anbernic RG353V and RG353VS are both RK3566 based handheld gaming devices
from Anbernic.
They are functionally very similar to the RG353P with the following
distinct differences:
- The battery size of the RG353V and RG353VS is 3200mAh instead of
3500mAh.
- The audio uses the PMIC's internal amplifier for a mono speaker
instead of an external amplifier with stereo speakers.
- The GPIOs for the R1 and R2 buttons are switched.
As for the differences between the RG353V and RG353VS, they are as
follows:
- The RG353VS has no touchscreen on i2c2.
- The RG353VS has no eMMC.
- The RG353VS has 1GB of RAM instead of 2GB.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20221028184045.13113-3-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch is to add a device tree for new board Hardkernel ODROID-M1
based on Rockchip RK3568, includes basic peripherals -
uart/eMMC/uSD/i2c and on-board ethernet.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
[aurelien@aurel32.net: addressed issues from initial review]
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Tested-by: Dan Johansen <strit@manjaro.org>
Link: https://lore.kernel.org/r/20220930051246.391614-3-aurelien@aurel32.net
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The PX30-uQ7 (Ringneck) SoM is a µQseven-compatible (40mmx70mm, MXM-230
connector) system-on-module from Theobroma Systems[1], featuring the
Rockchip PX30.
It provides the following feature set:
* up to 4GB DDR4
* up to 128GB on-module eMMC (with 8-bit 1.8V interface)
* SD card (on a baseboard) via edge connector
* Fast Ethernet with on-module TI DP83825I PHY
* MIPI-DSI/LVDS
* MIPI-CSI
* USB
- 1x USB 2.0 dual-role
- 3x USB 2.0 host
* on-module STM32 Cortex-M0 companion controller, implementing:
- low-power RTC functionality (ISL1208 emulation)
- fan controller (AMC6821 emulation)
- USB<->CAN bridge controller
* on-module Espressif ESP32 for Bluetooth + 2.4GHz WiFi
* on-module NXP SE05x Secure Element
[1] https://www.theobroma-systems.com/som-product/px30-%C2%B5q7/
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20220930-upstream-ringneck-v2-1-6671694b6934@theobroma-systems.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The only diffrence against the standrard edition is that the enterprise
one has a built-in EEPROM chip which stores a globally unique MAC address.
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Link: https://lore.kernel.org/r/20220915022511.4267-2-cnsztl@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Anbernic RG353P and RG503 are both RK3566 based handheld gaming devices
from Anbernic.
Both devices have:
- 2 SDMMC slots.
- A Realtek rtl8821cs WiFi/Bluetooth adapter.
- A mini HDMI port.
- A USB C host port and a USB C otg port (currently only working as
device).
- Multiple GPIO buttons and a single ADC button.
- Dual analog joysticks controlled via a GPIO mux.
- A headphone jack with amplified stereo speakers via a SGM4865 amp.
- A PWM based vibrator for force feedback.
The RG353P has:
- 2GB LPDDR4 RAM.
- A 32GB eMMC.
- A 3.5 inch 640x480 4-lane DSI panel of unknown origin with an i2c
controlled touchscreen (touchscreen is a Hynitron CST340).
The RG503 has:
- 1GB LPDDR4 RAM.
- A 5 inch 960x544 AMOLED 2-lane DSI/DBI panel manufactured by Samsung
with part number ams495qa04. Data for this panel is provided via the
DSI interface, however commands are sent via a 9-bit 3-wire SPI
interface. The MISO pin of SPI3 of the SOC is wired to the input of
the panel, so it must be bitbanged.
This devicetree enables the following hardware:
- HDMI (plus audio).
- Analog audio, including speakers.
- All buttons.
- All SDMMC/eMMC/SDIO controllers.
- The ADC joysticks (note a pending patch is required to use them).
- WiFi/Bluetooth (note out of tree drivers are required).
- The PWM based vibrator motor.
The following hardware is not enabled:
- The display panels (drivers are being written and there are issues
with the upstream DSI and VOP2 subsystems).
- Battery (driver pending).
- Touchscreen on the RG353P (note the i2c2 bus is enabled for it).
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20220906210324.28986-4-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for Radxa ROCK 4C+ SBC.
Key differences of 4C+ compared to previous ROCK Pi 4.
- Rockchip RK3399-T SoC
- DP from 4C replaced with micro HDMI 2K@60fps
- 4-lane MIPI DSI with 1920*1080
- RK817 Audio codec
Also, an official naming convention from Radxa mention to remove
Pi from board name, so this 4C+ is named as Radxa ROCK 4C+ not
Radxa ROCK Pi 4C+.
Signed-off-by: Stephen Chen <stephen@radxa.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20220902065057.97425-3-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is a basic DT containing regulators and UART, intended to be a
base that myself and others can add additional nodes in future patches.
Tested to work: booting from eMMC/SD, output over UART.
https://wiki.pine64.org/wiki/PinePhone_Pro
This is derived from the community pine64-org repo[0] with fixes from
https://megous.com/git/linux.
0. 261d3b5f8a
Signed-off-by: Martijn Braam <martijn@brixit.nl>
Co-developed-by: Kamil Trzciński <ayufan@ayufan.eu>
[no SoB, but Kamil is happy for this patch to be submitted]
Co-developed-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Co-developed-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Reviewed-by: Caleb Connolly <kc@postmarketos.org>
Reviewed-by: Nícolas F. R. A. Prado <n@nfraprado.net>
Tested-by: Nícolas F. R. A. Prado <n@nfraprado.net>
Link: https://lore.kernel.org/r/20220829050040.17330-2-tom@tom-fitzhenry.me.uk
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
EAIDK-610 is from OPEN AI LAB and popularly used by university
students.
Specification:
- Rockchip RK3399
- LPDDR3 4GB
- TF sd scard slot
- eMMC
- AP6255 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1
- 12V DC Power supply
This patch is test on Armbain and Glodroid with
HDMI/GPU/USB HOST/Type-C ADB/WIFI/BT.
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20220709103016.2754044-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
ROCK Pi S is RK3308 based SBC from radxa.com. ROCK Pi S has a,
- 256MB/512MB DDR3 RAM
- SD, NAND flash (optional on board 1/2/4/8Gb)
- 100MB ethernet, PoE (optional)
- Onboard 802.11 b/g/n wifi + Bluetooth 4.0 Module
- USB2.0 Type-A HOST x1
- USB3.0 Type-C OTG x1
- 26-pin expansion header
- USB Type-C DC 5V Power Supply
This patch enables
- Console
- NAND Flash
- SD Card
Signed-off-by: Akash Gajjar <akash@openedev.com>
[sjoerd: Sort dt nodes, drop properties duplicated from dtsi]
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Link: https://lore.kernel.org/r/20220614064858.1445817-3-sjoerd@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is the initial SoQuartz SoM device tree on a CM4IO carrier board.
This board outputs debug on uart2 and supports the following components:
Gigabit Ethernet
USB2 (OTG/Host shared)
PCIe 2.0 x1
HDMI (HDMI Port 0)
eDP (HDMI Port 1)
DSI (RPi compatible pinout)
CSI (RPi compatible pinout)
A/B/G/N WiFi
Bluetooth
SDMMC
eMMC
SPI NOR Flash (Not placed)
PI-40 compatible pin header
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20220429115252.2360496-7-pgwipeout@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add a device tree for the Pine64 Quartz64 Model B single board computer.
This board ouputs debug on uart2 and supports the following components:
Gigabit Ethernet
USB2 x2 (one port otg capable)
USB3
PCIe/SATA M2
HDMI
DSI (RPi compatible pinout)
CSI (RPi compatible pinout)
A/B/G/N WiFi
Bluetooth
SDMMC
eMMC
SPI Flash
PI-40 compatible pin header
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20220429115252.2360496-6-pgwipeout@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add basic device tree for the Radxa ROCK3 Model A board (with
the Rockchip RK3568 SoC) including Ethernet, USB2 and headphone
connector.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20220310210352.451136-3-michael.riesch@wolfvision.net
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The PineNote is a tablet from Pine64 based on the RK3566 SoC, featuring
4G/128G of storage, a 10.3" electrophoretic display (EPD) with two-color
frontlight, both EMR and capacitive digitizers, dual-band wireless,
quad-channel digital microphones, and stereo speakers.
There are two existing variants of the board. v1.1 was contained in some
early samples, and v1.2 was sold as the "PineNote Developer Edition".
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220130053803.43660-3-samuel@sholland.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds Devicetree for Bananapi R2 Pro based on RK3568.
Add uart/sd/emmc/i2c/rk809/tsadc nodes for basic function.
Gmac0 is directly connected to wan-port so usable without additional
driver.
On gmac1 there is a switch (rtl8367rb) connected which have not yet a
driver in mainline.
Patch also prepares nodes for GPIO header.
Co-developed-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20220123135116.136846-3-linux@fw-web.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Dumo is another variant of Scarlet, also known as the ASUS Chromebook
Tablet CT100. This is almost the same as Scarlet-Innolux, but uses a
board-specific calibration variant for the WiFi module.
Add a new device tree for it.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20210812094753.2359087-3-wenst@chromium.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add a basic dts for the Pine64 Quartz64 Model A Single Board Computer.
This board outputs on uart2 for debug.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210710151034.32857-5-pgwipeout@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
ROCK Pi 4B+ board is the successor of ROCK Pi 4B board.
Differences to the original version are
- has RK3399 OP1 SoC revision
- has eMMC (16 or 32 GB) soldered on board (no changes required,
since it is enabled in rk3399-rock-pi-4.dtsi)
- dev boards have SPI flash soldered, but as per manufacturer response,
this won't be the case for mass production boards
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20210618181256.27992-4-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
ROCK Pi 4A+ board is the successor of ROCK Pi 4A board.
Differences to the original version are
- has RK3399 OP1 SoC revision
- has eMMC (16 or 32 GB) soldered on board (no changes required,
since it is enabled in rk3399-rock-pi-4.dtsi)
- dev boards have SPI flash soldered, but as per manufacturer response,
this won't be the case for mass production boards
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20210618181256.27992-3-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
ROC-RK3399-PC-PLUS is the board inside the portable Firefly Station P1 Geek
PC. As a redesign after the ROC-RK3399-PC, it uses DC-12V as power input
and spares a USB 3 host port. It is also equipped with a USB WiFi chip and
audio codec without the mezzanine board.
- Rockchip RK3399 SoC
- 4GB LPDDR4 RAM
- 16MB SPI-Flash
- eMMC slot
- TF card slot
- USB 3.0 Port x 1, USB 2.0 Port x 1, TypeC Port x 1
- HDMI
- Gigabit Ethernet
- WiFi: RTL8723DU
- Audio: ES8388
- Key: Recovery
- LED: WORK, DIY
- IR
Signed-off-by: Kongxin Deng <dkx@t-chip.com.cn>
Signed-off-by: Levin Du <djw@t-chip.com.cn>
Link: https://lore.kernel.org/r/20210628035402.16812-3-djw@t-chip.com.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
ROC-RK3328-PC is the board inside the portable Firefly Station M1
Geek PC. As a redesign after the ROC-RK3328-CC, it uses TypeC as
power input and OTG port, embedded with eMMC 5.1 storage and a
SDIO WiFi/BT chip (RTL8723DS).
- Rockchip RK3328 SoC
- 2/4GB LPDDR3 RAM
- 16/32/64/128GB eMMC 5.1
- TF card slot
- USB 3.0 Port x 1, USB 2.0 Port x 1, TypeC Port x 1 (Power/OTG)
- HDMI
- Gigabit Ethernet
- WiFi: RTL8723DS
- Audio: RK3328
- Key: Power, Reset, Recovery
- LED: POWER, USER
- IR
Signed-off-by: Levin Du <djw@t-chip.com.cn>
Link: https://lore.kernel.org/r/20210709080126.17045-3-djw@t-chip.com.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds support for the NanoPi R4S from FriendlyArm.
Rockchip RK3399 SoC
1GB DDR3 or 4GB LPDDR4 RAM
Gigabit Ethernet (WAN)
Gigabit Ethernet (PCIe) (LAN)
USB 3.0 Port x 2
MicroSD slot
Reset button
WAN - LAN - SYS LED
Co-developed-by: Jensen Huang <jensenhuang@friendlyarm.com>
Signed-off-by: Jensen Huang <jensenhuang@friendlyarm.com>
[minor adjustments]
Co-developed-by: Marty Jones <mj8263788@gmail.com>
Signed-off-by: Marty Jones <mj8263788@gmail.com>
[further adjustments, fixed format issues]
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Link: https://lore.kernel.org/r/20210319051627.814-2-cnsztl@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The NanoPi M4B is a minor revision of the original M4.
The differences against the original Nanopi M4 that are common with the
other M4V2 revision include:
- microphone header removed
- power button added
- recovery button added
Additional changes specific to the M4B:
- USB 3.0 hub removed; board now has 2x USB 3.0 type-A ports and 2x
USB 2.0 ports
- ADB toggle switch added; this changes the top USB 3.0 host port to
a peripheral port
- Type-C port no longer supports data or PD
- WiFi/Bluetooth combo chip switched to AP6256, which supports BT 5.0
but only 1T1R (down from 2T2R) for WiFi
Add a new dts file for the new board revision that shows the difference
against the original.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210121162321.4538-5-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Radxa ROCK Pi E is a router oriented SBC based on Rockchip's RK3328 SoC.
As the official wiki page puts it, "E for Ethernets".
It features the RK3328 SoC, gigabit and fast Ethernet RJ45 ports, both
directly served by Ethernet controllers in the SoC, a USB 3.0 host port,
a power-only USB type-C port, a 3.5mm headphone jack for audio output,
two LEDs, a 40-pin Raspberry Pi style GPIO header, and optional WiFi+BT
and PoE header.
The board comes in multiple configurations, differing in the amount of
onboard RAM, the level of WiFi+BT (none, 802.11n 2.4GHz, or 802.11ac
2.4 GHz & 5 GHz), and whether PoE is supported or not. These variants
can all share the same device tree.
The USB 2.0 OTG controller is available on the 40-pin header. This is
not enabled in the device tree, since it is possible to use it in a
host-only configuration, or in OTG mode with an extra pin from the
header as the ID pin.
The device tree is based on the one of the Rock64, with various parts
modified to match the ROCK Pi E, and some parts updated to newer styles,
such as the gmac2io node's mdio sub-node.
Add a new device tree file for the new board.
The voltages for the adc-keys were selected to have some tolerances for
resistor variances and the ADC itself also causing voltage drops. Since
the recover button is the only button on the adc line, this should not
cause any issues.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210117100710.4857-4-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
C.TOUCH 2.0 is a general purpose carrier board with capacitive
touch interface support.
10.1" OF is a capacitive touch 10.1" Open Frame panel solutions.
PX30.Core needs to mount on top of C.TOUCH 2.0 carrier with pluged
10.1" OF for creating complete PX30.Core C.TOUCH 2.0 10.1" Open Frame.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20201109181017.206834-5-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
C.TOUCH 2.0 is a general purpose carrier board with capacitive
touch interface support.
PX30.Core needs to mount on top of this Carrier board for creating
complete PX30.Core C.TOUCH 2.0 board.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200929083217.25406-8-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board from Engicam.
PX30.Core needs to mount on top of this Evaluation board for
creating complete PX30.Core EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200929083217.25406-5-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds support for the NanoPi R2S from FriendlyARM.
Rockchip RK3328 SoC
1GB DDR4 RAM
Gigabit Ethernet (WAN)
Gigabit Ethernet (USB3) (LAN)
USB 2.0 Host Port
MicroSD slot
Reset button
WAN - LAN - SYS LED
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://lore.kernel.org/r/20200920154528.88185-2-mail@david-bauer.net
[adapted from sdmmc0m1_gpio to renamed sdmmc0m1_pin]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rk3318 A95X Z2 boards are sold as TV box.
No further documentation is given, but from the dts files
extracted it seems that the rk3318 processor is simulair
to the rk3328. This dts file contains only the basic nodes
that have support in the mainline kernel.
Features:
CPU: RK3318 Quad-Core Cortex-A53
GPU: Mali-450
RAM: 2/4GB DDR3
ROM: EMMC 16/32/64GB
HDMI: HDMI 2.0a for 4k@60Hz
Ethernet: 10/100M standard RJ-45
WiFi: 2.4G+5G WIFI, 802.11 b/g/n
Bluetooth: 4.0
1 x USB 3.0
1 x USB 2.0
1 x Micro SD card slot
1 x SPDIF
1 x AV
1 x DC IN
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200808160618.15445-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enabled
GPIO pin change compared to 4B, 4C.
So, add or enable difference nodes/properties in 4C dts
by including common dtsi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200807094826.12019-4-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
