As the PHY interface installed on the Eagle board provides TX and RX
channels delays, make the "phy-mode" property a board-specific one,
meant to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77970 SoC DTSI to use "rgmii" mode
and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the Draak board, provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77995 SoC DTSI to use "rgmii" mode
and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the ULCB board provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a7795/96 SoC DTSI to use "rgmii" mode\
and let the board files override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the Salvator-X[S] board, provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a7795/96/965 SoC DTSI to use "rgmii"
mode and let the board files override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Populate the device node for the Interrupt Controller for External
Devices (INTC-EX) on R-Car M3-N, which serves external IRQ pins
IRQ[0-5].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Populate the device node for the IIC Bus Interface for DVFS (IIC for
DVFS) on R-Car M3-N, and add an alias to fix its bus number.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the Renesas Salvator-XS (Salvator-X 2nd version)
development board equipped with an R-Car M3-N SiP.
Most features are enabled through the shared salvator-xs.dtsi board
description. The memory configuration is specific to the M3-N SiP.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Switch to SPDX-License-Identifier, update patch description]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#interrupt-cells" property and "interrupt-controller" label to
"interrupt-controller@e61c0000" device node.
This silences the following DTC compiler warnings:
Warning (interrupts_property): Missing interrupt-controller or
interrupt-map property in /soc/interrupt-controller@e61c0000
Warning (interrupts_property): Missing #interrupt-cells in
interrupt-parent /soc/interrupt-controller@e61c000
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#pwm-cells" property to "pwm@e6e31000" device node.
This silences the following DTC compiler warning:
Warning (pwms_property): Missing property '#pwm-cells' in node
/soc/pwm@e6e31000 or bad phandle (referred from /backlight:pwms[0])
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#phy-cells" property to "usb-phy@e65ee000" device node.
This silences the following DTC compiler warning:
Warning (phys_property): Missing property '#phy-cells' in node
/soc/usb-phy@e65ee000 or bad phandle (referred from
/soc/usb@ee020000:phys[0])
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove "reg" property from cache-controller-0 device node as it does not
have any unit address.
This silences the following DTC compiler warning:
Warning (unit_address_vs_reg): Node /cpus/cache-controller-0 has a reg
or ranges property, but no unit name
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#address-cells" and "#size-cells" properties to all place-holder nodes
that have children nodes defined by salvator-x[s].dtsi device tree.
This silences the following DTC compiler warnings:
Warning (reg_format): "reg" property in /soc/.. has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells
value for /soc/...
Warning (avoid_default_addr_size): Relying on default #size-cells value
for /soc/...
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "reg" properties to place-holder nodes with unit address defined for
R-Car M3-N SoC.
This silences the following DTC compiler warning:
Warning (unit_address_vs_reg): Node /soc/... has a unit name,
but no reg property
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add basic support for R-Car Salvator-X M3-N (R8A77965) board.
Based on original work from:
Takeshi Kihara <takeshi.kihara.df@renesas.com>
Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the Gen 3 R-Car M3-N SoC.
Based on original work from:
Takeshi Kihara <takeshi.kihara.df@renesas.com>
Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe frequencies, other than the default for CA53 cores. This is a
pre-requisite for using providing alternative frequencies for use with
CPUFreq with these cores.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe frequencies, other than the default for CA53 cores. This is a
pre-requisite for using providing alternative frequencies for use with
CPUFreq with these cores.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Condor board dependent part of the EtherAVB device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A77980 SoC based Condor board.
The board has 1 debug serial port (SCIF0); include support for it, so
that the serial console can work.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: correct memory size to 0x78000000 (2GiB)]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77980 part of the EtherAVB device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe [H]SCIF ports in the R8A77980 device tree.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the DU, providing only the VGA output for now.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The VSPD includes a CLUT on RPF2. Ensure that the register space is
mapped correctly to support this.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The VSPD includes a CLUT on RPF2. Ensure that the register space is
mapped correctly to support this.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The VSPD includes a CLUT on RPF2. Ensure that the register space is
mapped correctly to support this.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic r8a77995 part of the DU device node.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The single SDHI controller is connected to eMMC.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a77995 has a VSPBS to support image processing such as blending of
two input images, and has two VSPDs to handle display pipelines with a
DU.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[simon: updated base address of vsp node to fea28000]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The FCPVB handles the interface between the VSPB and memory, while the
FCPVD handles the interface between the VSPD and memory.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specify EtherAVB PHY IRQ in the Eagle board's device tree, now that we
have the GPIO support (previously phylib had to resort to polling).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe all 6 GPIO controllers in the R8A77970 device tree.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the (previously omitted) SCIF0 pin data to the Eagle board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77970 part of the PFC device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car D3 does not have the Stream Buffer for EtherAVB-IF (STBE).
Note that the RAVB driver does not use this region.
Fixes: f9ba0c4cfe ("arm64: dts: renesas: r8a77995: Add EthernetAVB device node")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car V3M does not have the Stream Buffer for EtherAVB-IF (STBE).
Note that the RAVB driver does not use this region.
Fixes: bea2ab136e ("arm64: dts: renesas: r8a77970: add EtherAVB support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe SYS-DMAC1/2 in the R8A77980 device tree.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The initial R8A77980 SoC device tree including Cortex-A53 CPU, GIC, timer,
CPG, RST, and SYSC.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No devices to add, I2C1 has an external connector only.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enables EEPROM on I2C0 on the Draak board.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
To be able to read fused calibration values from hardware the size of
the register resource of TSC1 needs to be incremented to cover one more
register which holds the information if the calibration values have been
fused or not.
Instead of increasing TSC1 size to the value from the datasheet update
all TSC's size to the smallest granularity of the address decoder
circuitry.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
To be able to read fused calibration values from hardware the size of
the register resource of TSC1 needs to be incremented to cover one more
register which holds the information if the calibration values have been
fused or not.
Instead of increasing TSC1 size to the value from the datasheet update
all TSC's size to the smallest granularity of the address decoder
circuitry
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move pmu_a53 and timer nodes from soc node to root node. The nodes that
have been moved do not have any register properties and thus shouldn't be
placed on the bus.
This problem is flagged by the compiler as follows:
$ make W=1
...
arch/arm64/boot/dts/renesas/r8a77995-draak.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a77995-draak.dtb: Warning (simple_bus_reg): Node /soc/pmu_a53 missing or empty reg/ranges property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move timer node from soc node to root node. The node that have been moved
do not have any register properties and thus shouldn't be placed on the
bus.
This problem is flagged by the compiler as follows:
$ make W=1
...
DTC arch/arm64/boot/dts/renesas/r8a77970-eagle.dtb
arch/arm64/boot/dts/renesas/r8a77970-eagle.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
DTC arch/arm64/boot/dts/renesas/r8a77970-v3msk.dtb
arch/arm64/boot/dts/renesas/r8a77970-v3msk.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We need to configure its GPIOs later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define OOP tables for all CPUs.
This allows CPUFreq to function.
Based in part on work by Hien Dang.
Signed-off-by: Dien Pham <dien.pham.ry@rvc.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Define OOP tables for all CPUs.
This allows CPUFreq to function.
Based in part on work by Hien Dang.
Signed-off-by: Dien Pham <dien.pham.ry@rvc.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Move scif node so that sub-nodes of the root node are in
alphabetical order.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
We get a moderate number of new machines this time, and only one
new SoC variant (Actions S700):
Actions:
S700 Soc and CubieBoard7 development board
Allo.com Sparky Single-board-computer
Allwinner:
Orange Pi R1 development board
Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
Axentia Nattis/Natte digital signage
sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
SolidRun Humminboard2 development board
Variscite DART-MX6 SoM and Carrier-board
Technologic TS-4600 and TS-7970 development board
Toradex Colibri iMX7D SoM board
v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
Moxa UC-8410A Series industrial computer
Gemini:
D-Link DNS-313 NAS enclosure
OMAP:
LogicPD OMAP35xx SOM-LV devkit
LogicPD OMAP35xx Torpedo devkit
Renesas:
r8a77970 (V3M) Starter Kit board
r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
Aspeed clk controller support
Freescale LS1088A, LS1021A device support
Gemini Ethernet, PCI, TVE, panel
Keystone gpio, qspi, more uarts
Mediatek cpufreq, regulator, clock, reset
Marvell thermal, cpufreq, nand
Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
Rockchip Mipi, GPU, display
Samsung Exynos5433 PMU, power domain, nfc
Spreadtrum: sc9860 clocks
Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qN1F
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"We get a moderate number of new machines this time, and only one new
SoC variant (Actions S700):
Actions:
- S700 Soc and CubieBoard7 development board
- Allo.com Sparky Single-board-computer
Allwinner:
- Orange Pi R1 development board
- Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
- Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
- Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
- Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
- Axentia Nattis/Natte digital signage
- sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
- SolidRun Humminboard2 development board
- Variscite DART-MX6 SoM and Carrier-board
- Technologic TS-4600 and TS-7970 development board
- Toradex Colibri iMX7D SoM board
- v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
- Moxa UC-8410A Series industrial computer
Gemini:
- D-Link DNS-313 NAS enclosure
OMAP:
- LogicPD OMAP35xx SOM-LV devkit
- LogicPD OMAP35xx Torpedo devkit
Renesas:
- r8a77970 (V3M) Starter Kit board
- r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
- Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
- Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
- Aspeed clk controller support
- Freescale LS1088A, LS1021A device support
- Gemini Ethernet, PCI, TVE, panel
- Keystone gpio, qspi, more uarts
- Mediatek cpufreq, regulator, clock, reset
- Marvell thermal, cpufreq, nand
- Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
- Rockchip Mipi, GPU, display
- Samsung Exynos5433 PMU, power domain, nfc
- Spreadtrum: sc9860 clocks
- Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ..."
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (690 commits)
arm64: dts: stratix10: fix SPI settings
ARM: dts: socfpga: add i2c reset signals
arm64: dts: stratix10: add USB ECC reset bit
arm64: dts: stratix10: enable USB on the devkit
ARM: dts: socfpga: disable over-current for Arria10 USB devkit
ARM: dts: Nokia N9: add support for up/down keys in the dts
ARM: dts: nomadik: add interrupt-parent for clcd
ARM: dts: Add ethernet to a bunch of platforms
ARM: dts: Add ethernet to the Gemini SoC
ARM: dts: rename oxnas dts files
ARM: dts: s5pv210: add interrupt-parent for ohci
ARM: lpc3250: fix uda1380 gpio numbers
ARM: dts: STi: Add gpio polarity for "hdmi,hpd-gpio" property
ARM: dts: dra7: Reduce shut down temperature of non-cpu thermal zones
ARM: dts: n900: Add aliases for lcd and tvout displays
ARM: dts: Update ti-sysc data for existing users
ARM: dts: Fix smartreflex compatible for omap3 shared mpu-iva instance
arm64: dts: marvell: armada-80x0: Fix pinctrl compatible string
arm: spear13xx: Fix spics gpio controller's warning
arm: spear13xx: Fix dmas cells
...
The present change is a bug fix for AVB link iteratively up/down.
Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
without user interaction,
- this may heal after some seconds or even stay for minutes.
As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.
Choosing to keep or remove the "renesas,no-ether-link" option will
have impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since
the RX & TX are enabled/disabled directly from adjust_link function
without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
HW interrogation. The HW check is made through the LMON pin in PSR
register which specifies AVB_LINK signal value (0 - at low level;
1 - at high level).
In conclusion, the present change is also a safety improvement because
it removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.
Fixes: dc36965a89 ("arm64: dts: r8a7796: salvator-x: Enable EthernetAVB")
Fixes: 6fa501c549 ("arm64: dts: r8a7795: enable EthernetAVB on Salvator-X")
Signed-off-by: Bogdan Mirea <Bogdan-Stefan_Mirea@mentor.com>
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The present change is a bug fix for AVB link iteratively up/down.
Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
without user interaction,
- this may heal after some seconds or even stay for minutes.
As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.
Choosing to keep or remove the "renesas,no-ether-link" option will
have impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since
the RX & TX are enabled/disabled directly from adjust_link function
without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
HW interrogation. The HW check is made through the LMON pin in PSR
register which specifies AVB_LINK signal value (0 - at low level;
1 - at high level).
In conclusion, the present change is also a safety improvement because
it removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.
Fixes: dc36965a89 ("arm64: dts: r8a7796: salvator-x: Enable EthernetAVB")
Fixes: 6fa501c549 ("arm64: dts: r8a7795: enable EthernetAVB on Salvator-X")
Signed-off-by: Bogdan Mirea <Bogdan-Stefan_Mirea@mentor.com>
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables usb3_peri0 that uses usb3_phy0 to enable VBUS
detection for the USB3.0 peripheral.
The Salvator-X[S] has USB3.0 type-A connector and supplies VBUS
if USB3.0 host runs. So, you need a special cable for it, and
to stop the VBUS supplies from the board, after you installs
a gadget driver, you should run the following command to avoid
conflict VBUS supply:
# echo 1 > /sys/kernel/debug/ee020000.usb/b_device
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables usb3_phy0 node for Salvator-X[S].
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add reg properties to pciec[01] placeholder nodes
This is to stop the compiler complaining as follows:
$ make
...
DTC arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@fe000000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@ee800000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/pcie@fe000000 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/pcie@ee800000 missing or empty reg/ranges property
DTC arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@fe000000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@ee800000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb: Warning (simple_bus_reg): Node /soc/pcie@fe000000 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb: Warning (simple_bus_reg): Node /soc/pcie@ee800000 missing or empty reg/ranges property
DTC arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@fe000000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@ee800000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb: Warning (simple_bus_reg): Node /soc/pcie@fe000000 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb: Warning (simple_bus_reg): Node /soc/pcie@ee800000 missing or empty reg/ranges property
DTC arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@fe000000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@ee800000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (simple_bus_reg): Node /soc/pcie@fe000000 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (simple_bus_reg): Node /soc/pcie@ee800000 missing or empty reg/ranges property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort root sub-nodes alphabetically for allow for easier maintenance
of this file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort root sub-nodes alphabetically for allow for easier maintenance
of this file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe the GPIO used to reset the Ethernet PHY for EthernetAVB.
This allows the driver to reset the PHY during probe and after system
resume.
On ULCB, the enable pin of the regulator providing PHY power is always
pulled high, but the driver may still need to reset the PHY if this
wasn't done by the bootloader before.
Inspired by patches in the BSP for the individual Salvator-X/XS boards
by Kazuya Mizuguchi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the GPIO used to reset the Ethernet PHY for EthernetAVB.
This allows the driver to reset the PHY during probe and after system
resume.
This fixes Ethernet operation after resume from s2ram on Salvator-XS,
where the enable pin of the regulator providing PHY power is connected
to PRESETn, and PSCI powers down the SoC during system suspend.
On Salvator-X, the enable pin is always pulled high, but the driver may
still need to reset the PHY if this wasn't done by the bootloader
before.
Inspired by patches in the BSP for the individual Salvator-X/XS boards
by Kazuya Mizuguchi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the commit 833bdb47c8 ("dt-bindings: power: add R8A77970 SYSC
power domain definitions") has hit Linus' tree, we can replace the bare
numbers (we had to use to avoid a cross tree dependency) with these macro
definitions...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the commit ecadea00f5 ("dt-bindings: clock: Add R8A77970 CPG
core clock definitions") has hit Linus' tree, we can replace the bare
numbers (we had to use to avoid a cross tree dependency) with these macro
definitions...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the V3M Starter Kit board dependent part of the EtherAVB
device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the V3M Starter Kit board.
The board has 1 debug serial port (SCIF0); include support for it,
so that the serial console can work.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add IPMMU-RT to the Ethernet-AVB device node.
Based on work by Magnus Damm for the r8a7795.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add r8a77995 IPMMU nodes and keep all disabled by default.
Based on work for the r8a7795 and r8a7796 by Magnus Damm
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the r8a77970 device nodes for IPMMU-DS1, IPMMU-RT
and the shared IPMMU-MM device.
Based on work for the r8a7796 by Magnus Damm.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IPMMU-RT to the Ethernet-AVB device node.
Based on work by Magnus Damm for the r8a7795.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up r8a77970 DMAC nodes to the IPMMU. In particular
SYS-DMAC1 and SYS-DMAC2 get tied to IPMMU-DS1.
Based on work for the r8a7796 by Magnus Damm.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add r8a77970 IPMMU nodes and keep all disabled by default.
Based on work for the r8a7796 by Magnus Damm
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort includes used in r8a77970 DTS to improve maintainability
and for consistency with other R-Car DTS files.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch changes the number of GPIO bank 1 ports to 29 because GP-1-28
port pin of R8A7795 ES2.0 SoC support was added.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Fixes: 291e0c4994 ("arm64: dts: r8a7795: Add support for R-Car H3 ES2.0")
[geert: Keep 28 GPIOs on H3 ES1.x after r8a7795.dtsi sharing]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds CAN FD controller node for r8a77995.
Based on a patch for r8a7796 by Chris Paterson.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds CAN controller nodes for r8a77995.
Based on a patch for r8a7796 by Chris Paterson.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds external CAN clock node for r8a77995. This clock can be used as
fCAN clock of CAN and CAN FD controller.
Based on a patch for r8a7796 by Chris Paterson.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document clearly which SoC this DTS applies to, to distinguish from
Salvator-XS boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document clearly which SoC this DTS applies to, to distinguish from
Salvator-X boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document clearly which SoC this DTS applies to, to distinguish from
Salvator-X boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document clearly which SoC this DTS applies to, to distinguish from
Salvator-X boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the ROHM BD9571MWV PMIC.
This was based on the example in the DT binding documentation, but using
IRQ0 instead of a GPIO interrupt, as that matches the schematics, and
because INTC-EX is a simpler block.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the r8a7795 device nodes for IPMMU-VI0, IPMMU-VP1, IPMMU-DS0,
IPMMU-DS1 and the shared IPMMU-MM device.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the r8a7795 ES1.x device node for IPMMU-MP1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IPMMU-HC to the SATA device node.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IPMMU-DS0 to the Ethernet-AVB device node.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPVI devices to allow use of VSPI with IPMMU-VP.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPVI devices to allow use of VSPI with
IPMMU-VP0 and IPMMU-VP1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPVB devices to allow use of VSPBC/VSPBD with
IPMMU-VP0 and IPMMU-VP1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPF devices to allow use of FDP1 with IPMMU-VP0.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPF devices to allow use of FDP1 with IPMMU-VP.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPVD devices to allow use of the VSP and DU
together with IPMMU-VI0.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPVD devices to allow use of the VSP and DU
together with IPMMU-VI1 and IPMMU-VI1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up r8a7795 ES2.0 Audio-DMAC nodes to the IPMMU-MP0.
Hook up r8a7795 ES1.x Audio-DMAC nodes to the IPMMU-MP1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up r8a7795 SYS-DMAC nodes to the IPMMUs. In particular SYS-DMAC0 gets
tied to IPMMU-DS0, and SYS-DMAC1 and SYS-DMAC2 get tied to IPMMU-DS1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add r8a7795 ES1.x IPMMU nodes and keep all disabled by default.
This is a follow-up to a patch that adds IPMMU device nodes that
are common to r8a7795 ES1.x and ES2.0
Power domains are omitted as they appear to be undocumented.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add r8a7795 IPMMU nodes and keep all disabled by default.
This includes all IPMMU devices for r8a7795 ES2.0. Those
not present in r8a7795 ES1.x are removed from the DT for those
SoCs using delete-node. A follow-up patch will add IPMMU devices
to ES1.x which are not also present in ES2.0.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car D3 has only one SDHI controller.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Differs from other Gen3 SoCs in that each controller only supports eight
channels.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ULCB-KF has a USB2.0 dual-role channel (CN13).
This adds dr_mode property for USB2.0 channel 0 (EHCI/OHCI and HS-USB)
as "otg".
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports USB2 PHY channel #0 on ULCB Kingfisher board
The dedicated USB0_PWEN pin is used to control CN13 VBUS source from U43
power supply.
MAX3355 can also provide VBUS, hence it should be disabled via OTG_OFFVBUSn
node coming from gpio expander TCA9539.
Set MAX3355 enabled using OTG_EXTLPn node to be able to read OTG ID of
CN13.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the r8a7795 device nodes for IPMMU-DS0, IPMMU-DS1, IPMMU-MP,
IPMMU-VI0, IPMMU-VC0 and the shared IPMMU-MM device.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IPMMU-DS0 to the Ethernet-AVB device node.
Based on work by Magnus Damm for the r8a7795.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPVI devices to allow use of VSPI with IPMMU-VC0.
Based on work for the r8a7795 by Magnus Damm.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPF devices to allow use of FDP1 with IPMMU-VI0.
Based on work by Magnus Damm for the r8a7795.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up r8a7796 Audio-DMAC nodes to the IPMMU-MP.
Based on work for the r8a7795 by Magnus Damm.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up r8a7796 DMAC nodes to the IPMMUs. In particular SYS-DMAC0
gets tied to IPMMU-DS0, and SYS-DMAC1 and SYS-DMAC2 get tied to IPMMU-DS1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add r8a7796 IPMMU nodes and keep all disabled by default.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add initial support for the Renesas Salvator-XS (Salvator-X 2nd version)
development board equipped with an R-Car M3-W SiP.
Based on work for the Salvator-X and -XS boards with M3-W resp. H3 SiPs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the Watchdog Timer (WDT) controller on the Renesas Eagle
board equipped with an R-Car V3M (r8a77970) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Watchdog Timer (WDT) controller on the
Renesas R-Car V3M (r8a77970) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use newly added R-Car SDHI Gen3 fallback compat string
in the DT of the r8a7796 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use newly added R-Car SDHI Gen3 fallback compat string
in the DT of the r8a7795 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
These boards are known to have eMMC issues with the default driver type.
Specify a working one.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We add device tree files for a couple of additional SoCs in various areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for networking,
Amlogic A113D for audio, and Renesas R-Car V3M for automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX, Amlogic
and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues that
the latest version of 'dtc' now warns about. Unfortunately there is still
a lot left to do.
A rework of the ARM foundation model introduced several new files
for common variations of the model.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TnSo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Arnd Bergmann:
"We add device tree files for a couple of additional SoCs in various
areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for
networking, Amlogic A113D for audio, and Renesas R-Car V3M for
automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX,
Amlogic and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues
that the latest version of 'dtc' now warns about. Unfortunately there
is still a lot left to do.
A rework of the ARM foundation model introduced several new files for
common variations of the model"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (599 commits)
arm64: dts: uniphier: route on-board device IRQ to GPIO controller for PXs3
dt-bindings: bus: Add documentation for the Technologic Systems NBUS
arm64: dts: actions: s900-bubblegum-96: Add fake uart5 clock
ARM: dts: owl-s500: Add CubieBoard6
dt-bindings: arm: actions: Add CubieBoard6
ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock
ARM: dts: owl-s500: Set power domains for CPU2 and CPU3
arm: dts: mt7623: remove unused compatible string for pio node
arm: dts: mt7623: update usb related nodes
arm: dts: mt7623: update crypto node
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
...
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing memory
leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node. The
prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to dtb
compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage Technology,
shimafuji, Tecon Microprocessor Technologies, DH electronics GmbH,
Opal Kelly, and Next Thing
-----BEGIN PGP SIGNATURE-----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=jgpN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
If CONFIG_OF_ALL_DTBS is enabled, "make ARCH=arm64 dtbs" compiles each
DTB twice; one from arch/arm64/boot/dts/*/Makefile and the other from
the dtb-$(CONFIG_OF_ALL_DTBS) line in arch/arm64/boot/dts/Makefile.
It could be a race problem when building DTBS in parallel.
Another minor issue is CONFIG_OF_ALL_DTBS covers only *.dts in vendor
sub-directories, so this broke when Broadcom added one more hierarchy
in arch/arm64/boot/dts/broadcom/<soc>/.
One idea to fix the issues in a clean way is to move DTB handling
to Kbuild core scripts. Makefile.dtbinst already recognizes dtb-y
natively, so it should not hurt to do so.
Add $(dtb-y) to extra-y, and $(dtb-) as well if CONFIG_OF_ALL_DTBS is
enabled. All clutter things in Makefiles go away.
As a bonus clean-up, I also removed dts-dirs. Just use subdir-y
directly to traverse sub-directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[robh: corrected BUILTIN_DTB to CONFIG_BUILTIN_DTB]
Signed-off-by: Rob Herring <robh@kernel.org>
We need to add "clean-files" in Makfiles to clean up DT blobs, but we
often miss to do so.
Since there are no source files that end with .dtb or .dtb.S, so we
can clean-up those files from the top-level Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since Salvator-X[S] have a USB2.0 dual-role channel (CN9), this patch
adds dr_mode property for USB2.0 channel 0 (EHCI/OHCI and HS-USB)
as "otg".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use newly added R-Car GPIO Gen3 fallback compat string
in place of now deprecated non-generation specific
R-Car GPIO fallback compat string in the DT of the r8a7796 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use newly added R-Car GPIO Gen3 fallback compat string
in place of now deprecated non-generation specific
R-Car GPIO fallback compat string in the DT of the r8a7795 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
"audio_clkout" is dummy clock of <&rcar_sound 0> to avoid clock loop
which invites probe conflict. Thus <&rcar_sound 0> and "audio_clkout"
should be same value.
On commit 2752660a37 ("arm64: dts: renesas: ulcb: sound
clock-frequency needs descending order") exchanged <&rcar_sound 0>,
but it didn't modify "audio_clkout".
This patch fixup it.
Fixes: 2752660a37 ("arm64: dts: renesas: ulcb: sound clock-frequency needs descending order")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
"audio_clkout" is dummy clock of <&rcar_sound 0> to avoid clock loop
which invites probe conflict. Thus <&rcar_sound 0> and "audio_clkout"
should be same value.
On commit 5e2feac330 ("arm64: renesas: salvator-common: sound
clock-frequency needs descending order") exchanged <&rcar_sound 0>,
but it didn't modify "audio_clkout".
This patch fixup it.
Fixes: 5e2feac330 ("arm64: renesas: salvator-common: sound clock-frequency needs descending order")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Eagle board dependent part of the EtherAVB device node.
Enable DHCP and NFS root for the kernel booting.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Interrupt Controller for External Devices
(INTC-EX) on R-Car D3, which serves external IRQ pins IRQ[0-5].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Interrupt Controller for External Devices
(INTC-EX) on R-Car V3M, which serves external IRQ pins IRQ[0-5].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Interrupt Controller for External Devices
(INTC-EX) on R-Car M3-W, which serves external IRQ pins IRQ[0-5].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds gpio hogs for USB3 hub on ULCB Kingfisher board to power up and
remove from reset the hub
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports PCA9548 I2C switch on I2C4 bus on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports PCA9548 I2C switch on I2C2 bus on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports TCA9539 gpio expanders on I2C4 bus on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports TCA9539 gpio expanders on I2C2 bus on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports USB3.0 Host on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports PCIE0/1 on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports HSUSB on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports CAN0/1 on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports SCIF1 on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the H3ULCB ES2.0+ SoC with Kingfisher
extension infotainment board.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the H3ULCB ES1.x SoC with Kingfisher
extension infotainment board.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the M3ULCB with Kingfisher extension
infotainment board.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial common dtsi file for Kingfisher infotainment board (R-Car
Starter Kit extension)
This commit supports the following peripherals:
- HSCIF0
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables PWM channel 0 and 1 on the draak. Each channel
connects to LTC2644 for brightness control.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since a R-Car Gen3 bootloader enables the PFC of USB3.0 channel 0,
the USB3.0 host controller works without this setting on the kernel.
But, this setting should have salvator-common.dtsi. So, this patch
adds the pfc node for USB3.0 channel 0.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A77970 SoC based Eagle board.
The board has 1 debug serial port (SCIF0); include support for it,
so that the serial console can work.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since the Ethernet AVB driver doesn't support AVB_PHY_INT handling
and it will be handled by a phy driver as a gpio pin, this patch
removes the "avb_phy_int" from the avb_pins node.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Fixes: 4503b50eac ("arm64: dts: renesas: r8a77995: draak: enable EthernetAVB")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since the Ethernet AVB driver doesn't support AVB_PHY_INT handling
and it will be handled by a phy driver as a gpio pin, this patch
removes the "avb_phy_int" from the avb_pins node.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 133ace3f38 ("arm64: dts: ulcb: Set drive-strength for ravb pins")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since the Ethernet AVB driver doesn't support AVB_PHY_INT handling
and it will be handled by a phy driver as a gpio pin, this patch
removes the "avb_phy_int" from the avb_pins node.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 7d73a4da26 ("arm64: dts: r8a7795: salvator-x: Set drive-strength for ravb pins")
Fixes: 4903987033be ("arm64: dts: r8a7796: salvator-x: Set drive-strength for ravb pins")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77970 part of the EtherAVB device node.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe [H]SCIF ports in the R8A77970 device tree.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe SYS-DMAC1/2 in the R8A77970 device tree.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The initial R8A77970 SoC device tree including Cortex-A53 CPU, GIC, timer,
CPG, RST, and SYSC.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the hardcoded clock indices by R8A77995_CLK_* symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the hardcoded power domain indices by R8A77995_PD_* symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Node names should not use numerical suffixes if the nodes can be
distinguished by unit-address.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU is already wired up to the HDMI encoder, all we need to do is
enable it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch changes the name from from e6060000.pfc and pfc@e6060000 to
e6060000.pin-controller and pin-controller@e6060000 like other Renesas
SoCs.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7796 has a single FDP1 instance.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As usual, device tree updates is the bulk of our material in this merge
window. This time around, 559 patches affecting both 32- and 64-bit
platforms.
Changes are too many to list individually, but some of the larger ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also several
new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R45j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM/arm64 Devicetree updates from Olof Johansson:
"As usual, device tree updates is the bulk of our material in this
merge window. This time around, 559 patches affecting both 32- and
64-bit platforms.
Changes are too many to list individually, but some of the larger
ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also
several new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board"
* tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (559 commits)
ARM: dts: at91: at91sam9g45: add AC97
arm64: dts: marvell: mcbin: enable more networking ports
arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
arm64: dts: marvell: add TX interrupts for PPv2.2
arm64: dts: uniphier: add PXs3 SoC support
ARM: dts: uniphier: add pinctrl groups of ethernet phy mode
ARM: dts: uniphier: fix size of sdctrl nodes
ARM: dts: uniphier: add AIDET nodes
arm64: dts: uniphier: fix size of sdctrl node
arm64: dts: uniphier: add AIDET nodes
Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
arm64: dts: uniphier: add reset controller node of analog amplifier
arm64: dts: marvell: add Device Tree files for Armada-8KP
arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
dt-bindings: add rk3399-q7 SoM
ARM: dts: rockchip: enable usb for rv1108-evb
ARM: dts: rockchip: add usb nodes for rv1108 SoCs
dt-bindings: update grf-binding for rv1108 SoCs
ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
...
* Add PFC device node to R-Car D3 (r8a77995)
This is a step towards enabling devices that use multiplexed pins
- including ethernet - on boards that use the r8a7796 SoC.
* Add USB nodes to R-Car M3-W (r8a7796)
This is a step towards enabling USB devices on boards that
use the r8a7796 SoC.
* Use newly added Gen-3 fallback compat string
This is consistent with ongoing efforts to use per-generation
fallback strings where appropriate across devices found
on R-Car SoCs. The aim of the effort being to strike a balance
between the limited information available about the compatibility
of devices found on different SoCs and the desire to ease enabling
devices on new SoCs.
This has no run-time effect due to the presence of a per-SoC
compat string.
* Cleanup whitespace and extra LVDS port label
Minor cleanups, no run-time effect.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6XqO
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt2-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt64
Pull "Second Round of Renesas ARM64 Based SoC DT Updates for v4.14" from Simon Horman:
* Add PFC device node to R-Car D3 (r8a77995)
This is a step towards enabling devices that use multiplexed pins
- including ethernet - on boards that use the r8a7796 SoC.
* Add USB nodes to R-Car M3-W (r8a7796)
This is a step towards enabling USB devices on boards that
use the r8a7796 SoC.
* Use newly added Gen-3 fallback compat string
This is consistent with ongoing efforts to use per-generation
fallback strings where appropriate across devices found
on R-Car SoCs. The aim of the effort being to strike a balance
between the limited information available about the compatibility
of devices found on different SoCs and the desire to ease enabling
devices on new SoCs.
This has no run-time effect due to the presence of a per-SoC
compat string.
* Cleanup whitespace and extra LVDS port label
Minor cleanups, no run-time effect.
* tag 'renesas-arm64-dt2-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: r8a77995: add pfc device node
arm64: dts: r8a7796: Add HSUSB device node
arm64: dts: r8a7796: Add USB-DMAC device nodes
arm64: dts: r8a7796: Add USB3.0 host device node
arm64: dts: r8a7796: add USB2.0 Host (EHCI/OHCI) device nodes
arm64: dts: r8a7796: add usb2_phy device nodes
arm64: dts: r8a7795: correct whitespace of companion property
arm64: dts: r8a7795: Use R-Car SATA Gen3 fallback compat string
arm64: dts: salvator-common: Remove extra LVDS port label
Use newly added R-Car SATA Gen3 fallback compat string
in the DT of the r8a7795 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before the fallback compat string is considered.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The DU LVDS output is on port 3 on R8A7795 but on port 2 on R8A7796. The
lvds_connector label thus can't be defined in salvator-common.dtsi,
common to the two SoCs.
The lvds_connector label is meant for convenience to be referenced from
panel device tree files, such as r8a77xx-aa104xd12-panel.dtsi or
r8a77xx-aa121td01-panel.dtsi. As those files are not included in any
device tree source, and the label never used elsewhere, we can simply
remove it. Out-of-tree patches that include panel device tree files can
then add a
#define lvds_connector du_out_lvds0
before including the panel device tree file.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Add usb2.0 for R-Car H3 (r8a7795) ES2.0 SoC
* Add R-Car D3 (r8a77995) SoC and Draak board support
Adds minimal support for the R-Car D3 SoC and the Draak development
board, allowing to boot from a ramdisk using a serial console.
* Add Add VC6 clock generator to R-Car H3 (r8a7795)/Salvator-XS board
The VC6 is an I2C-controlled programmable clock generator, used on the
board to provide a display dot clock. Add it to DT.
* Add missing second pair of DMA names to MSIOF nodes to
R-Car M3-W (r8a7796) SoC
MSIOF0 and MSIOF1 are tied to two DMA controllers through two pairs of
DMA specifiers. However, the second pair of corresponding DMA names was
missing.
* Add support for the DU to R-Car H3 (r8a7795) SoC
Add a compatible string and VSP links to the DU node. The H3 ES1.x and H3
ES2.0 are compatible save for the links to the VSPs that are described
explicitly in DT, so there's no need for a new ES2-specific compatible
string.
* Enable HDMI on R-Car H3 (r8a7795) and M3-W (r8a7796) ULCB boards
* Enable DU on R-Car M3-W (r8a7796) Salvator-X board
* Enable I2C for DVFS on R-Car H3 (r8a7795) and M3-W (r8a7796) ULCB boards
* Add Add DRIF support to R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
Ramesh Shanmugasundaram says, "R-Car Gen3 DRIF is a SPI like receive only
slave device."
* Move CPG_AUDIO_CLK_I from board to soc files
Geert Uytterhoeven says, "The definition of CPG_AUDIO_CLK_I is
SoC-specific, not board-specific."
* Add IMR-LX4 support to R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
Sergei Shtylyov says, "The image renderer light extended 4 (IMR-LX4) or
the distortion correction engine is a drawing processor with a simple
instruction system capable of referencing data on an external memory as
2D texture data and performing texture mapping and drawing with respect
to any shape that is split into triangular objects."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ehXW
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt64
Pull "Renesas ARM64 Based SoC DT Updates for v4.14" from Simon Horman:
* Add usb2.0 for R-Car H3 (r8a7795) ES2.0 SoC
* Add R-Car D3 (r8a77995) SoC and Draak board support
Adds minimal support for the R-Car D3 SoC and the Draak development
board, allowing to boot from a ramdisk using a serial console.
* Add Add VC6 clock generator to R-Car H3 (r8a7795)/Salvator-XS board
The VC6 is an I2C-controlled programmable clock generator, used on the
board to provide a display dot clock. Add it to DT.
* Add missing second pair of DMA names to MSIOF nodes to
R-Car M3-W (r8a7796) SoC
MSIOF0 and MSIOF1 are tied to two DMA controllers through two pairs of
DMA specifiers. However, the second pair of corresponding DMA names was
missing.
* Add support for the DU to R-Car H3 (r8a7795) SoC
Add a compatible string and VSP links to the DU node. The H3 ES1.x and H3
ES2.0 are compatible save for the links to the VSPs that are described
explicitly in DT, so there's no need for a new ES2-specific compatible
string.
* Enable HDMI on R-Car H3 (r8a7795) and M3-W (r8a7796) ULCB boards
* Enable DU on R-Car M3-W (r8a7796) Salvator-X board
* Enable I2C for DVFS on R-Car H3 (r8a7795) and M3-W (r8a7796) ULCB boards
* Add Add DRIF support to R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
Ramesh Shanmugasundaram says, "R-Car Gen3 DRIF is a SPI like receive only
slave device."
* Move CPG_AUDIO_CLK_I from board to soc files
Geert Uytterhoeven says, "The definition of CPG_AUDIO_CLK_I is
SoC-specific, not board-specific."
* Add IMR-LX4 support to R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
Sergei Shtylyov says, "The image renderer light extended 4 (IMR-LX4) or
the distortion correction engine is a drawing processor with a simple
instruction system capable of referencing data on an external memory as
2D texture data and performing texture mapping and drawing with respect
to any shape that is split into triangular objects."
* tag 'renesas-arm64-dt-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (31 commits)
arm64: dts: renesas: r8a7795: add hsusb ch3 device node
arm64: dts: renesas: r8a7795: add usb-dmac ch2 and ch3 device nodes
arm64: dts: renesas: r8a7795: add usb2.0 host ch3 device nodes
arm64: dts: renesas: r8a7795: add usb2_phy ch3 device node
arm64: dts: renesas: r8a7795: Add usb companion property in EHCI
arm64: dts: renesas: Add Renesas Draak board support
arm64: dts: renesas: Add Renesas R8A77995 SoC support
arm64: renesas: Add Renesas R8A77995 Kconfig support
arm64: dts: r8a7795: salvator-xs: Connect DU dot clocks 0 and 3
arm64: dts: salvator-xs: Add VC6 clock generator
arm64: dts: r8a7796: Add missing second pair of DMA names to MSIOF nodes
arm64: dts: r8a7795: Add all MSIOF nodes
arm64: dts: r8a7795: Add support for the DU
arm64: dts: ulcb: Enable HDMI output
arm64: dts: ulcb: Add HDMI output connector
arm64: dts: r8a7796: m3ulcb: Add DU external dot clocks
arm64: dts: r8a7795: h3ulcb: Add DU external dot clocks
arm64: dts: ulcb: Add DU external dot clock sources
arm64: dts: r8a7796: salvator-x: Enable HDMI output
arm64: dts: r8a7796: salvator-x: Add DU external dot clocks
...
clock name of "audio_clkout" is used by Renesas sound driver.
This duplicated naming breaks its clock registering/unregistering.
Especially, when unbind/bind it can't handle clkout correctly.
This patch renames "audio_clkout" to "audio-clkout" to avoid
naming conflict.
Fixes: 8a8f181d2c ("arm64: renesas: salvator-x: use CS2000 as AUDIO_CLK_B")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds support for hsusb ch3 device nodes for R-Car H3 ES2.0.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds support for usb-dmac ch2 and ch3 device nodes for
R-Car H3 ES2.0.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds support for usb2.0 host ch3 device nodes for R-Car
H3 ES2.0.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds support for usb3_phy ch3 device node for R-Car H3 ES2.0.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the "companion" property in the EHCI ch0, ch1 and
ch2 nodes to wait for the usb companion controller startup at resume.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[remove ch3 node and revise the commit log]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the Renesas Draak board based on R-Car D3:
- Memory,
- Main crystal,
- Serial console,
- Watchdog.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU dot clocks 0 and 3 are provided by the programmable VC6 clock
generator. Connect them to the clock source node.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The VC6 is an I2C-controlled programmable clock generator, used on the
board to provide a display dot clock. Add it to DT.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
MSIOF0 and MSIOF1 are tied to two DMA controllers through two pairs of
DMA specifiers. However, the second pair of corresponding DMA names was
missing.
Fixes: 80fab06e25 ("arm64: dts: r8a7796: Add all MSIOF nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all MSIOF SPI controllers, incl. clocks, power
domain, dma, and reset properties.
Due to a hardware erratum on R-Car H3 ES1.x, using MSIOF for SPI is only
supported on ES2.0 and later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a compatible string and VSP links to the DU node. The H3 ES1.x and
H3 ES2.0 are compatible save for the links to the VSPs that are
described explicitly in DT, so there's no need for a new ES2-specific
compatible string.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the HDMI encoder for ULCB board and hook it up to the HDMI connector.
The HDMI encoder and connector are available on both the H3 and M3-W ULCB boards.
Add them to the ulcb.dtsi file.
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The ULCB board has one HDMI output connector.
This connector is available on both the H3 and M3-W ULCB boards.
Add this to the ulcb.dtsi file.
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU0/DU1/DU2 external dot clocks are provided by the programmable
Versaclock5 clock generator.
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU0/DU1/DU2/DU3 external dot clocks are provided by the programmable
Versaclock5 clock generator.
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU0/DU1/DU2/DU3 external dot clocks are generated by an I2C-controlled
programmable clock generator.
Clock generator is available on both the H3 and M3-W ULCB boards.
Add this to the ulcb.dtsi file.
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the HDMI encoder for the M3-W Salvator-X board and hook it up to
the HDMI connector.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU1 external dot clock is provided by the fixed frequency clock
generator X21, while the DU0 and DU2 clocks are provided by the
programmable Versaclock5 clock generator.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the HDMI encoder to the R8A7796 DT in disabled state.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DU device to r8a7796.dtsi in a disabled state.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The FCPs handle the interface between various IP cores and memory. Add
the instances related to the FDPs and VSP2s.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables I2C4 for ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables I2C for DVFS device for ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The definition of CPG_AUDIO_CLK_I is SoC-specific, not board-specific.
Hence move it from the board-specific .dts files to the SoC-specific
.dtsi files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the IMR-LX4 devices in the R8A7796 device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the IMR-LX4 devices in the R8A7795 device tree.
Based on the original (and large) patch by Konstantin Kozhevnikov
<Konstantin.Kozhevnikov@cogentembedded.com>.
Signed-off-by: Konstantin Kozhevnikov <Konstantin.Kozhevnikov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Correct order of sound clock frequencies for ULCB boards
used with r8a7795 and r8a7796 SoCs.
These sounds clock frequencies are used as the ADG clock (output clocks
for audio module) initial setting and sound codec's initial system clock
which needs the maximum clock frequency. Thus, descending order is
required.
Fixes: 9f22774c21 ("arm64: dts: ulcb: add 12288000 for sound ADG")
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: rewrote changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
It will be used ADG clock initial settings, and will be
sound codec's initial system clock which needs maximum clock frequency.
Thus, descending order is required
Fixes: d37d2b3c0e ("arm64: dts: salvator-x: add 12288000 for sound ADG")
Fixes: 0b03c32db0 ("arm64: dts: r8a7795: salvator-x: Add support for R-Car H3 ES2.0")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Note that the audio module has resets for the Serial Sound Interfaces
only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Note that the audio module has resets for the Serial Sound Interfaces
only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the Renesas Salvator-XS (Salvator-X 2nd version)
development board equipped with an R-Car H3 ES2.0 SiP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Renesas Salvator-XS (Salvator-X 2nd version) development board can
be equipped with either an R-Car H3 ES2.0 or M3-W ES1.x SiP, which are
pin-compatible.
Add initial support for the common parts of the Salvator-XS board into
its own .dtsi file, to be included by the DTSes for the H3/M3-W
versions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Renesas Salvator-X and Salvator-XS (Salvator-X 2nd version) boards
are very similar. To avoid duplication, prepare for the advent of the
latter by extracting the common board parts into its own .dtsi file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car Gen3 SoCs contain multiple PWM modules. Hence to avoid conflicts,
pinctrl subnodes for PWM should include indices referring to their
instances.
Fixes: b33be33670 ("arm64: dts: salvator-x: Add panel backlight support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Split off support for H3ULCB boards with the ES1.x revision of the R-Car
H3 SoC into a separate file. The main r8a7795-h3ulcb.dts file now
corresponds to H3ULCB with R-Car H3 ES2.0 or later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tested with a Salvator-X.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tested with a Salvator-X.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current rcar_sound only has 11289600 (= for 44.1kHz) clock-frequency,
but it needs 12288000 for 48kHz too.
Otherwise, 48kHz based sound can't handle correctly.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current rcar_sound only has 11289600 (= for 44.1kHz) clock-frequency,
but it needs 12288000 for 48kHz too.
Otherwise, 48kHz based sound can't handle correctly.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Split off support for Salvator-X boards with the ES1.x revision of the
R-Car H3 SoC into a separate file. The main r8a7795-salvator-x.dts file
now corresponds to Salvator-X with R-Car H3 ES2.0 or later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update r8a7795.dtsi so it corresponds to R-Car H3 ES2.0 or later:
- The following devices no longer exist on ES2.0, and are thus removed:
fcpf2, fcpvd3, fcpvi2, fdp1-2, usb3-if1, vspd3, vspi2.
- The DU <-> VSPD topology is different on ES2.0, hence remove the
"compatible" and "vsps" properties from the DU node until the driver
can handle this.
Move support for the ES1.x revision of the R-Car H3 SoC into a
separate file. To avoid duplication, r8a7795-es1.dtsi includes
r8a7795.dtsi, and adds device nodes and properties where needed.
Note that while currently r8a7795-es1.dtsi only adds device nodes,
removal of devices nodes and properties can be implemented using the
/delete-node/ and /delete-property/ keywords, as shown below:
&soc {
/delete-node/ <name>@<addr>;
};
&<label> {
/delete-property/ <prop>;
};
Switch r8a7795-salvator-x.dts and r8a7795-h3ulcb.dts from r8a7795.dtsi
to r8a7795-es1.dtsi to preserve compatibility.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The EthernetAVB should not depend on the bootloader to setup correct
drive-strength values. Values for drive-strength where found by
examining the registers after the bootloader has configured the
registers and successfully used the EthernetAVB.
Based on:
* commit 7d73a4da26 ("arm64: dts: r8a7795: salvator-x: Set drive-strength
for ravb pins")
* commit 4903987033be ("arm64: dts: r8a7796: salvator-x: Set drive-strength
for ravb pins")
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the HDMI encoders for the H3 Salvator-X board. The number of
encoders varies between the H3 and M3-W SoCs, so they can't be enabled
in the common salvator-x.dtsi file.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU1 and DU2 external dot clocks are provided by the fixed frequency
clock generators X21 and X22, while the DU0 and DU3 clocks are provided
by the programmable Versaclock5 clock generator.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Salvator-X board has two HDMI output connectors. Add them to the
common salvator-x.dtsi.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU1 and DU2 external dot clocks are fixed frequency clock generators
running at 33MHz, while the DU0 and DU3 external dot clocks are
generated by an I2C-controlled programmable clock generator.
All those clock generators are available on both the H3 and M3-W
Salvator-X boards. Add them to the salvator-x.dtsi file.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT nodes for the two HDMI encoders in disabled state.
Based on work by Koji Matsuoka.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The panel backlight is controlled through a GPIO and a PWM channel.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[simon: apply to salvator-x.dtsi instead of r8a7795-salvator-x.dts]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Renesas ULCB development board can be equipped with either an R-Car
H3 or M3-W SiP, which are pin-compatible. Both boards use different
DTBs.
Reduce duplication by extracting common ULCB board support into its own
.dtsi file. References to SoC-specific clocks are handled through cpp
definitions. Sort device nodes while at it.
For H3ULCB, there are no functional changes.
For M3ULCB, the following new devices are now described in DT:
- External audio, CAN, and PCIe clocks,
- CS2000 clock generator,
- AK4613 Audio Codec.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Renesas Salvator-X development board can be equipped with either an
R-Car H3 or M3-W SiP, which are pin-compatible. Both boards use
different DTBs.
Reduce duplication by extracting common Salvator-X board support into
its own .dtsi file. References to SoC-specific clocks are handled
through cpp definitions. Sort device nodes while at it.
For boards with an R-Car H3 SiP, there are no functional changes.
For boards with an R-Car M3-W SiP, the following new devices are now
described in DT:
- External audio, CAN, and PCIe clocks,
- USB Vbus regulator,
- CS2000 clock generator,
- AK4613 Audio Codec,
- VGA.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add empty device nodes serving as placeholders for devices that are not
yet supported and/or tested on R-Car M3-W, but are supported and used on
Salvator-X or H3ULCB boards equipped with an R-Car H3 SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the external PCIe bus clock as a zero Hz fixed-frequency clock.
Boards that provide this clock should override it.
Based on r8a7795.dtsi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the external audio clocks as zero Hz fixed-frequency clocks.
Boards that provide these clocks should override them.
Based on commit 623197b90c ("arm64: renesas: r8a7795: Sound SSI
PIO support").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from e6060000.pfc and pfc@e6060000 to
e6060000.pin-controller and pin-controller@e6060000.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
The EthernetAVB should not depend on the bootloader to setup correct
drive-strength values. Values for drive-strength where found by
examining the registers after the bootloader has configured the
registers and successfully used the EthernetAVB.
Based on commit 7d73a4da26 ("arm64: dts: r8a7795: salvator-x: Set
drive-strength for ravb pins").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set PHY rxc-skew-ps to 1500 and all other values to their default values.
This is intended to to address failures in the case of 1Gbps communication
using the salvator-x board with the KSZ9031RNX phy. This has been
reported to occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs.
Based in a similar patch for the r8a7796 salvator-x by Kazuya Mizuguchi.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports HS200 mode for eMMC on H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports HS200 mode for eMMC on M3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch updates memory region:
- After changes, the new map of the m3ulcb board on R8A7796 SoC
Bank0: 1GiB RAM : 0x000048000000 -> 0x0007fffffff
Bank1: 1GiB RAM : 0x000600000000 -> 0x0063fffffff
- Before changes, the old map looked like this:
Bank0: 1GiB RAM : 0x000048000000 -> 0x0007fffffff
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports I2C2 bus on M3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The current practice is to not add _clk suffixes to clock node names in
DT, as these names are used as the actual clock names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add properties to describe the reset topology for on-SoC devices:
- Add the "#reset-cells" property to the CPG/MSSR device node,
- Add resets and reset-names properties to the various device nodes.
This allows to reset SoC devices using the Reset Controller API.
Note that all resets added match the corresponding module clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add properties to describe the reset topology for on-SoC devices:
- Add the "#reset-cells" property to the CPG/MSSR device node,
- Add resets and reset-names properties to the various device nodes.
This allows to reset SoC devices using the Reset Controller API.
Note that all resets added match the corresponding module clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the r8a7795 SATA device node to use a 2MiB I/O space as specified
in the "72. Serial-ATA" section of R-Car-Gen3-rev0.52E.pdf
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7796.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7796.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk and pcie_bus_clk device nodes are already enabled in
r8a7795.dtsi, so there is no need to update their statuses again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7795.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the performance monitor unit for the Cortex-A53 cores on the
R8A7796 SoC.
Extracted from a patch by Takeshi Kihara in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds Cortex-A53 CPU cores of R8A7796 SoC, and sets a total of
6 cores (2 x Cortex-A57 + 4 x Cortex-A53).
Based on a patch by Takeshi Kihara in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Cortex-A53 L2 cache-controller.
The L2 cache for the Cortex-A53 CPU cores is 512 KiB large (organized as
32 KiB x 16 ways).
Extracted from a patch by Takeshi Kihara in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the performance monitor unit for the Cortex-A57 cores on the
R8A7796 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds Cortex-A57 CPU cores to R8A7796 SoC for a total of
2 x Cortex-A57.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Rebased]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current Audio-DMAC is assigned "rx" as Audio-DMAC0, "tx" as Audio-DMAC1.
Thus, DVC "tx" should be assigned as Audio-DMAC1, instead of Audio-DMAC0.
Because of this, current platform board (using SRC/DVC/SSI)
Playback/Capture both will use same Audio-DMAC0
(but it depends on audio data path).
First note is that this "rx" and "tx" are from each IP point,
it doesn't mean Playback/Capture.
Second note is that Audio DMAC assigned on DT is only for
Audio-DMAC, Audio-DMAC-peri-peri has no entry.
=> Audio-DMAC
-> Audio-DMAC-peri-peri
-- HW connection
Playback case
[Mem] => [SRC]--[DVC] -> [SSI]--[Codec]
rx ~~~~~~~~~~~~
Capture
[Mem] <= [DVC]--[SRC] <- [SSI]--[Codec]
tx ~~~~~~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The EthernetAVB should not depend on the bootloader to setup correct
drive-strength values. Values for drive-strength where found by
examining the registers after the bootloader has configured the
registers and successfully used the EthernetAVB.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A57 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: 1561f20760 ("arm64: dts: r8a7796: Add Renesas R8A7796 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A57/A53 cache controllers are integrated controllers, and
thus the device nodes representing them should not have unit-addresses
or reg properties.
Fixes: 6f7bf82cc9 ("arm64: dts: r8a7795: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
>From PSCI v1.0, Suspend-to-RAM is supported via SYSTEM_SUSPEND PSCI
function call. Hence, upgrade PSCI version for R-Car M3-W to support
Suspend-to-RAM.
The Suspend-to-RAM is highly dependent on ARM Trusted Firwmare support
since necessary callback functions will be registered after a query
to ARM Trusted Firmware about SYSTEM_SUSPEND support.
Since PSCI v1.0 is backward compatible with PSCI v0.2, CPU Hotplug and
CPUIdle should be able to work normally with this change.
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Keep "arm,psci-0.2"]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
>From PSCI v1.0, Suspend-to-RAM is supported via SYSTEM_SUSPEND PSCI
function call. Hence, upgrade PSCI version for R-Car H3 to support
Suspend-to-RAM.
The Suspend-to-RAM is highly dependent on ARM Trusted Firwmare support
since necessary callback functions will be registered after a query
to ARM Trusted Firmware about SYSTEM_SUSPEND support.
Since PSCI v1.0 is backward compatible with PSCI v0.2, CPU Hotplug and
CPUIdle should be able to work normally with this change.
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Keep "arm,psci-0.2"]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the performance monitor unit for the Cortex-A53 cores on the
R8A7795 SoC.
Extracted from a patch by Takeshi Kihara in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds Cortex-A53 CPU cores to r8a7795 SoC for a total of 8
cores (4 x Cortex-A57 + 4 x Cortex-A53).
Based on work by Takeshi Kihara and Dirk Behme.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enables the SCIF hooked up to the DEBUG1 connector.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all R-Car H3 SCIF serial ports, incl. clocks
and power domain.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all HSCIF serial ports, incl. clocks, and
power domain.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: express register size in hex; refer to power domain in changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set PHY rxc-skew-ps to 1500 and all other values to their default values.
This is intended to to address failures in the case of 1Gbps communication
using the by salvator-x board with the KSZ9031RNX phy. This has been
reported to occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since commit 61fccb2d62 ("ravb: Add tx and rx clock internal delays mode
of APSR") the EthernetAVB driver enables tx and rx clock internal delay
modes (TDM and RDM) depending on the phy mode as follows:
phy mode | ASPR delay mode
-----------+----------------
rgmii-id | TDM and RDM
rgmii-rxid | RDM
rgmii-txid | TDM
And prior to the above commit no internal delay mode settings were
implemented for any phy mode.
With this and the above change present tx internal delay mode is enabled
which has been observed to address failures in the case of 1Gbps
communication using the by salvator-x board with the KSZ9031RNX phy. This
has been reported to occur with both the r8a7795 (H3) and r8a7796 (M3-W)
SoCs.
With the above patch present but this patch present tx and rx internal
delay modes are enabled; and with the above patch and this present absent
no internal delay modes are enabled. In both cases failures have been
observed when using 1Gbps communication in the environments described
above.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set PHY rxc-skew-ps to 1500 and all other values to their default values.
This is intended to to address failures in the case of 1Gbps communication
using the by h3ulcb board with the KSZ9031RNX phy.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set PHY rxc-skew-ps to 1500 and all other values to their default values.
This is intended to to address failures in the case of 1Gbps communication
using the by salvator-x board with the KSZ9031RNX phy. This has been
reported to occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since commit 61fccb2d62 ("ravb: Add tx and rx clock internal delays mode
of APSR") the EthernetAVB driver enables tx and rx clock internal delay
modes (TDM and RDM) depending on the phy mode as follows:
phy mode | ASPR delay mode
-----------+----------------
rgmii-id | TDM and RDM
rgmii-rxid | RDM
rgmii-txid | TDM
And prior to the above commit no internal delay mode settings were
implemented for any phy mode.
With this and the above change present tx internal delay mode is enabled
which has been observed to address failures in the case of 1Gbps
communication using the by salvator-x board with the KSZ9031RNX phy. This
has been reported to occur with both the r8a7795 (H3) and r8a7796 (M3-W)
SoCs.
With the above patch present but this patch present tx and rx internal
delay modes are enabled; and with the above patch and this present absent
no internal delay modes are enabled. In both cases failures have been
observed when using 1Gbps communication in the environments described
above.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables I2C for DVFS device for for Salvator-X board on
R8A7795 SoC.
Signed-off-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds support of I2C for DVFS device for Salvator-X board on
R8A7796 SoC.
Signed-off-by: Dien Pham <dien.pham.ry@rvc.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
r8a779[56] SoCs:
* Mark EthernetAVB device node disabled in DT for r8a779[56] SoCs
- They are enabled as appropriate in board DT files
* Link ARM GIC to clock and clock domain on r8a779[56] SoCs
* Add thermal support
r8a7795 SoC:
* Tidyup audma definition order on r8a7795 SoC
* Add missing power-domains property for SATA
r8a7795/h3ulcb board:
* Add MIX/CTU support as per support present in DT for r8a7796
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KG8o
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt2-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt64
Second Round of Renesas ARM64 Based SoC DT Updates for v4.11
r8a779[56] SoCs:
* Mark EthernetAVB device node disabled in DT for r8a779[56] SoCs
- They are enabled as appropriate in board DT files
* Link ARM GIC to clock and clock domain on r8a779[56] SoCs
* Add thermal support
r8a7795 SoC:
* Tidyup audma definition order on r8a7795 SoC
* Add missing power-domains property for SATA
r8a7795/h3ulcb board:
* Add MIX/CTU support as per support present in DT for r8a7796
* tag 'renesas-arm64-dt2-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: r8a7796: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: tidyup audma definition order
arm64: dts: r8a7796: Link ARM GIC to clock and clock domain
arm64: dts: r8a7795: Link ARM GIC to clock and clock domain
arm64: dts: r8a7796: Add R-Car Gen3 thermal support
arm64: dts: r8a7795: Add R-Car Gen3 thermal support
arm64: dts: r8a7795: Add missing power-domains property for sata
arm64: dts: h3ulcb: follow sound CTU/MIX supports
Signed-off-by: Olof Johansson <olof@lixom.net>
Device nodes representing I/O devices should be marked disabled in the
SoC-specific DTS, and overridden by board-specific DTSes where needed.
Fixes: 8e8b9eaef8 ("arm64: dts: renesas: r8a7796: Add EthernetAVB instance")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Device nodes representing I/O devices should be marked disabled in the
SoC-specific DTS, and overridden by board-specific DTSes where needed.
Fixes: a92843c8a6 ("arm64: dts: r8a7795: add EthernetAVB device node")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current r8a7795.dtsi defines audma -> ipmmu -> dma order.
Because of this order, dma can connect to ipmmu, but
audma can't connect to it.
This patch moves audma order as ipmmu -> dma -> audma.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-AP module clock, and add it to the SYSC
"always-on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-AP module clock, and add it to the SYSC
"always-on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This went unnoticed as the sata_rcar driver doesn't support Runtime PM
yet, but manages module clocks manually.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Add PWM, and sound MIX and CTU support to r8a7795 SoC
* Add CAN, CAN FD and all MSIOF nodes to r8a7796 SoC
* Use Gen 3 fallback binding for i2c, msiof, PCIE and USB2 phy
* Enable Ethernet and 4 GiB memory on r8a7796/salvator-x board
* Add r8a7796/salvator-x board part number to bindings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=s00S
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt64
Renesas ARM64 Based SoC DT Updates for v4.11
* Add PWM, and sound MIX and CTU support to r8a7795 SoC
* Add CAN, CAN FD and all MSIOF nodes to r8a7796 SoC
* Use Gen 3 fallback binding for i2c, msiof, PCIE and USB2 phy
* Enable Ethernet and 4 GiB memory on r8a7796/salvator-x board
* Add r8a7796/salvator-x board part number to bindings
* tag 'renesas-arm64-dt-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: r8a7795: Add PWM support
arm64: dts: r8a7796: Use R-Car Gen 3 fallback binding for msiof nodes
arm64: dts: r8a7796: salvator-x: Enable EthernetAVB
arm64: dts: renesas: r8a7796: Add EthernetAVB instance
arm64: dts: r8a7796: salvator-x: Update memory node to 4 GiB map
arm64: dts: r8a7796: Use R-Car Gen 3 fallback binding for i2c nodes
arm64: dts: r8a7795: Use R-Car Gen 3 fallback binding for i2c nodes
arm64: dts: r8a7795: Use Gen 3 fallback compat string for PCIE
arm64: dts: r8a7795: add sound MIX support
arm64: dts: r8a7795: add sound CTU support
arm64: dts: r8a7795: Use renesas,rcar-gen3-usb2-phy fallback binding
arm64: renesas: r8a7796/salvator-x: Add board part number to DT bindings
arm64: dts: r8a7796: Add CAN FD support
arm64: dts: r8a7796: Add CAN support
arm64: dts: r8a7796: Add CAN external clock support
arm64: dts: r8a7796: Add all MSIOF nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
* Provide sd0_uhs node
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XZkS
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Renesas ARM Based SoC Fixes for v4.10
* Provide sd0_uhs node
* tag 'renesas-fixes-for-v4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: h3ulcb: Provide sd0_uhs node
Add the 7 PWM channels to the r8a7795 device tree, in the disabled
state.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use recently added R-Car Gen 3 fallback binding for msiof nodes in
DT for r8a7796 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7796 and the
fallback binding for R-Car Gen 3.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch updates memory region:
- After changes, the new map of the Salvator-X board on R8A7796 SoC
Bank0: 2GiB RAM : 0x000048000000 -> 0x000bfffffff
Bank1: 2GiB RAM : 0x000600000000 -> 0x0067fffffff
- Before changes, the old map looked like this:
Bank0: 2GiB RAM : 0x000048000000 -> 0x000bfffffff
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Correct size of old map]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use recently added R-Car Gen 3 fallback binding for i2c nodes in
DT for r8a7796 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7796 and the
fallback binding for R-Car Gen 3.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use recently added R-Car Gen 3 fallback binding for i2c nodes in
DT for r8a7795 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7795 and the
fallback binding for R-Car Gen 3.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use recently added en 3 fallback compat string for PCIE
in r8a7795 DT.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CTU (= Channel Transfer Unit) support which is needed
to sound mixing.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
A fallback binding for the Renesas R-Car Gen3 for USB2.0 PHY driver was
added by commit cde7bc367f ("phy: rcar-gen3-usb2: add fallback binding").
This patch makes use of this binding in the DT for the r8a7795 SoC.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Adds CAN FD controller node for r8a7796.
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds CAN controller nodes for r8a7796.
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds external CAN clock node for r8a7796. This clock can be used as
fCAN clock of CAN and CAN FD controller.
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all MSIOF SPI controllers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
A couple of interesting new SoC platforms are now supported, these are
the respective DTS sources:
- Samsung Exynos5433 mobile phone platform, including an (almost) fully
supported phone reference board.
- Hisilicon Hip07 server platform and D05 board, the latest iteration
of their product line, now with 64 Cortex-A72 cores across two
sockets.
- Allwinner A64 SoC, the first 64-bit chip from their "sunxi" product
line, used in Android tablets and ultra-cheap development boards
- NXP LS1046A Communication processor, improving on the earlier LS1043A
with faster CPU cores
- Qualcomm MSM8992 (Snapdragon 808) and MSM8994 (Snapdragon 810)
mobile phone SoCs
- Early support for the Nvidia Tegra Tegra186 SoC
- Amlogic S905D is a minor variant of their existing Android consumer
product line
- Rockchip PX5 automotive platform, a close relative of their popular
rk3368 Android tablet chips
Aside from the respective evaluation platforms for the above
chips, there are only a few consumer devices and boards added
this time:
- Huawei Nexus 6P (Angler) mobile phone
- LG Nexus 5x (Bullhead) mobile phone
- Nexbox A1 and A95X Android TV boxes
- Pine64 development board based on Allwinner A64
- Globalscale Marvell ESPRESSOBin community board based on Armada 3700
- Renesas "R-Car Starter Kit Pro" (M3ULCB) low-cost automotive board
For the existing platforms, we get bug fixes and new peripheral support
for Juno, Renesas, Uniphier, Amlogic, Samsung, Broadcom, Rockchip, Berlin,
and ZTE.
Conflicts:
- Documentation/devicetree/bindings/arm/shmobile.txt: a
rename/add conflict, keep both modifications and maintain
alphabetical ordering.
- arch/arm64/boot/dts/*/*.dtsi: nodes were added in netdev,
mmc and clk, keep both sides in each case.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=geT0
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"A couple of interesting new SoC platforms are now supported, these are
the respective DTS sources:
- Samsung Exynos5433 mobile phone platform, including an (almost)
fully supported phone reference board.
- Hisilicon Hip07 server platform and D05 board, the latest iteration
of their product line, now with 64 Cortex-A72 cores across two
sockets.
- Allwinner A64 SoC, the first 64-bit chip from their "sunxi" product
line, used in Android tablets and ultra-cheap development boards
- NXP LS1046A Communication processor, improving on the earlier
LS1043A with faster CPU cores
- Qualcomm MSM8992 (Snapdragon 808) and MSM8994 (Snapdragon 810)
mobile phone SoCs
- Early support for the Nvidia Tegra Tegra186 SoC
- Amlogic S905D is a minor variant of their existing Android consumer
product line
- Rockchip PX5 automotive platform, a close relative of their popular
rk3368 Android tablet chips
Aside from the respective evaluation platforms for the above chips,
there are only a few consumer devices and boards added this time:
- Huawei Nexus 6P (Angler) mobile phone
- LG Nexus 5x (Bullhead) mobile phone
- Nexbox A1 and A95X Android TV boxes
- Pine64 development board based on Allwinner A64
- Globalscale Marvell ESPRESSOBin community board based on Armada 3700
- Renesas "R-Car Starter Kit Pro" (M3ULCB) low-cost automotive board
For the existing platforms, we get bug fixes and new peripheral
support for Juno, Renesas, Uniphier, Amlogic, Samsung, Broadcom,
Rockchip, Berlin, and ZTE"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (168 commits)
arm64: dts: fix build errors from missing dependencies
ARM64: dts: meson-gxbb: add SCPI pre-1.0 compatible
ARM64: dts: meson-gxl: Add support for Nexbox A95X
ARM64: dts: meson-gxm: Add support for the Nexbox A1
ARM: dts: artpec: add pcie support
arm64: dts: berlin4ct-dmp: add missing unit name to /memory node
arm64: dts: berlin4ct-stb: add missing unit name to /memory node
arm64: dts: berlin4ct: add missing unit name to /soc node
arm64: dts: qcom: msm8916: Add ddr support to sdhc1
arm64: dts: exynos: Enable HS400 mode for eMMC for TM2
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM64: dts: Add support for Meson GXM
dt-bindings: add rockchip RK1108 Evaluation board
arm64: dts: NS2: Add PCI PHYs
arm64: dts: NS2: enable sdio1
arm64: dts: exynos: Add the mshc_2 node for supporting T-Flash
arm64: tegra: Add NVIDIA P2771 board support
arm64: tegra: Enable PSCI on P3310
arm64: tegra: Add NVIDIA P3310 processor module support
arm64: tegra: Add GPIO controllers on Tegra186
...
Provide separaate sd0 and sd0_uhs nodes rather than duplicate sd0 nodes.
Cc: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Fixes: 93373c309a ("arm64: dts: h3ulcb: rename SDHI0 pins")
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This changes SDHI0 pin names for H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports SDHI2 for H3ULCB onboard eMMC
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports SDHI2 for M3ULCB onboard eMMC
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports SDHI0 on M3ULCB board SD card slot
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports watchdog timer for M3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables EXTALR clock that can be used for the watchdog.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports GPIO keys on M3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports GPIO leds on M3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A7796 SoC based M3ULCB low cost
board (R-Car Starter Kit Pro)
This commit supports the following peripherals:
- SCIF (console)
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This updates H3ULCB device tree header with official board name
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since this board doesn't mount pull-up/down registers for
USB1_{OVC,PWEN} pins, we should enable bias setting to pull these
pins up/down.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Based on work for the r8a7796 by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Enable the exposed SD card slots in the DT of the r8a7796/salvator-x.
Based on work for the r8a7795/salvator-x by Ai Kyuse.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a device node for the RST module, which provides a.o. reset control
and mode pin monitoring.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Add a device node for the RST module, which provides a.o. reset control
and mode pin monitoring.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Add SDHI nodes to the DT of the r8a7796 SoC.
Based on the DT of the r8a7795 SoC.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The SoC-specific compatible strings have been removed from the FCP DT
bindings, removed them from the device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declaring the endpoint makes LVDS enablement easier by just including
the corresponding panel's dtsi file.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
It can be used for the watchdog.
Based on similar work for r8a7795/salvator-x by Wolfram Sang.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports GPIO leds on H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports SSI sound for H3ULCB board.
SSI DMA mode used. CS2000 used as AUDIO_CLK_B.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports GPIO keys on H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove cap-mmc-highspeed property from SDHI2 and SDHI3.
This property is unnecessary as the driver automatically sets
the highspeed capability. Furthermore its use is inconsistent with SDHI0
and SDHI1 which are also highspeed capable but do not have this property
present.
Found by inspection.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports watchdog timer for H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables EXTALR clock that can be used for the watchdog.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports I2C2 bus on H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports Ethernet AVB on H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A7795 SoC based H3ULCB low cost
board.
This commit supports the following peripherals:
- SCIF (console)
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The audio-dmac nodes used the generic compatible property only.
Add the SoC-specific one, to make it future proof.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Only the VGA output is supported for now.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DU device to r8a7795.dtsi in a disabled state.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7795 has 9 VSP instances.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The FCPs handle the interface between various IP cores and memory. Add
the instances related to the VSP2s.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We have to set SW15 to pin 2-3 side on the board before we use CN9
as USB host or peripheral.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch also adds a regulator node for USB2.0 to handle VBUS on/off
by the phy-rcar-gen3-usb2 driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the upper limit otherwise the driver cannot utilize max speeds.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Provide nodes for the FCP devices dedicated to the FDP device channels.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the Watchdog Timer (WDT) controller on the Renesas Salvator-X
board equipped with an R-Car M3-W (r8a7796) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Watchdog Timer (WDT) controller on the Renesas
R-Car M3-W (r8a7796) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up all devices that are part of the CPG/MSSR Clock Domain to the
SYSC "always-on" PM Domain, for a more consistent device-power-area
description in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the System Controller.
Hook up the Cortex-A57 CPU core and L2 cache/SCU to their respective PM
Domains.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the Gen 3 R-Car M3-W SoC.
Based on work for the r8a7795 and r8a7796 SoCs by
Takeshi Kihara, Dirk Behme and Geert Uytterhoeven.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Adds CAN FD controller node for r8a7795.
Note: CAN FD controller register base address specified in R-Car Gen3
Hardware User Manual v0.5E is incorrect. The correct address is:
CAN FD - 0xe66c0000
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
For consistency with a57_0/a57_1 cpu nodes, and all other nodes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Drop 0x from unit address of gic as this is the desired form for
a unit address.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Warning (unit_address_vs_reg): Node /regulator@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@4 has a unit name, but no reg property
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Warning (unit_address_vs_reg): Node /cache-controller@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /cache-controller@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,dvc/dvc@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,dvc/dvc@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,src/src@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,src/src@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,src/src@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,src/src@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,src/src@4 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,src/src@5 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,src/src@6 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,src/src@7 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,src/src@8 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,src/src@9 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,ssi/ssi@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,ssi/ssi@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,ssi/ssi@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,ssi/ssi@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,ssi/ssi@4 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,ssi/ssi@5 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,ssi/ssi@6 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,ssi/ssi@7 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,ssi/ssi@8 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/sound@ec500000/rcar_sound,ssi/ssi@9 has a unit name, but no reg property
Move the cache-controller nodes under the cpus node, and make their unit
names and reg properties match the MPIDR values.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up the RWDT device node to the SYSC "always-on" PM Domain, for a
more consistent device-power-area description in DT.
Cfr. commit 38dbb45ee4 ("arm64: dts: r8a7795: Use SYSC "always-on" PM
Domain")
Fixes: f43838a7ae014cba ("arm64: dts: r8a7795: Add RWDT node")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There are some requirements about the GIC-400 memory layout and its
mapping if using 64k aligned base addresses like on r8a7795.
See e.g.
http://xenbits.xen.org/gitweb/?p=xen.git;a=commit;h=21550029f709072aacf3b9
Map the whole memory range instead of only 0x2000. This will fix
the issue that some hypervisors, e.g. Xen, fail to handle the
interrupts correctly.
Signed-off-by: Pooya Keshavarzi <Pooya.Keshavarzi@de.bosch.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On the Salvator-X development board, the RTS and CTS pins of debug
serial-1 port SCIF1 are wired to the CP2102 Serial-USB bridge. Reflect
this in the DTS by adding the "uart-has-rtscts" property to the scif1
device node.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This is a collection of a few late fixes and other misc. stuff that
had dependencies on things being merged from other trees.
The Renesas R-Car power domain handling, and the Nvidia Tegra USB
support both hand notable changes that required changing the DT binding
in a way that only provides compatibility with old DT blobs on new
kernels but not vice versa. As a consequence, the DT changes
are based on top of the driver changes and are now in this branch.
For NXP i.MX and Samsung Exynos, the changes in here depend on
other changes that got merged through the clk maintainer tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=I0Be
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
The Renesas R-Car power domain handling, and the Nvidia Tegra USB
support both hand notable changes that required changing the DT
binding in a way that only provides compatibility with old DT blobs on
new kernels but not vice versa. As a consequence, the DT changes are
based on top of the driver changes and are now in this branch.
For NXP i.MX and Samsung Exynos, the changes in here depend on other
changes that got merged through the clk maintainer tree"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
ARM: dts: exynos: Add support of Bus frequency using VDD_INT for exynos5422-odroidxu3
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos542x SoC
ARM: dts: exynos: Add NoC Probe dt node for Exynos542x SoC
ARM: dts: exynos: Add support of bus frequency for exynos4412-trats/odroidu3
ARM: dts: exynos: Expand the voltage range of buck1/3 regulator for exynos4412-odroidu3
ARM: dts: exynos: Add support of bus frequency using VDD_INT for exynos3250-rinato
ARM: dts: exynos: Add exynos4412-ppmu-common dtsi to delete duplicate PPMU nodes
ARM: dts: exynos: Add bus nodes using VDD_MIF for Exynos4210
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos4x12
ARM: dts: exynos: Add bus nodes using VDD_MIF for Exynos4x12
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos3250
ARM: dts: exynos: Add DMC bus frequency for exynos3250-rinato/monk
ARM: dts: exynos: Add DMC bus node for Exynos3250
ARM: tegra: Enable XUSB on Nyan
ARM: tegra: Enable XUSB on Jetson TK1
ARM: tegra: Enable XUSB on Venice2
ARM: tegra: Add Tegra124 XUSB controller
ARM: tegra: Move Tegra124 to the new XUSB pad controller binding
ARM: dts: r8a7794: Use SYSC "always-on" PM Domain
ARM: dts: r8a7793: Use SYSC "always-on" PM Domain
...
Hook up all devices that are part of the CPG/MSSR Clock Domain to the
SYSC "always-on" PM Domain, for a more consistent device-power-area
description in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the System Controller.
Hook up the Cortex-A57 CPU cores and the Cortex-A57 and Cortex A53 L2
caches/SCUs to their respective PM Domains.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
clk_get() on a disabled clock node will return -EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their devices' clocks properties.
Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them, to prevent this.
Reported-by: Jürg Billeter <j@bitron.ch>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
It can be used for the watchdog.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds CAN controller nodes for r8a7795.
Note: CAN channel register base address mentioned in R-Car Gen3 Hardware
User Manual v0.5E is incorrect. The corrected base addresses are:
CAN Channel 0 - 0xe6c30000
CAN Channel 1 - 0xe6c38000
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds external CAN clock node for r8a7795. This clock can be used as
fCAN clock of CAN and CAN FD controller.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since 16ccaf5bb5 ("pinctrl: sh-pfc: Accept standard function, pins and
groups properties") renesas pfc drivers accept generic "function", "pins"
and "groups" properties.
This patch updates the kzm9g device tree to use the generic properties.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
We should set SW15 to pin 2-3 side on the board before we use CN9
as USB host or peripheral.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This board has a MAX3355 chip. However, we cannot use the extcon/max3355
driver because the ID pin doesn't connect to a gpio pin (in other words,
it connects to the SoC specific pin).
And, the phy-rcar-gen3-usb2 driver cannot handle such a chip for now.
So, this patch enables usb2_phy of channel 1 and 2.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the exposed SD card slots. The on-board eMMC needs to wait until we
fixed the 8bit support.
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[wsa: squashed some fixes and added mmc-caps]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Besides the distributor and the CPU interface the GIC-400 additionally
supports the virtual interface control blocks and the virtual CPU interfaces.
Add the physical base addresses and size for these.
See
http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0471b/index.html
-> 3.2. GIC-400 register map
and Linux kernel's
Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt
for more details.
For the at GICH Virtual interface control blocks at 0xf1040000 cover the
whole 128kB (0x20000) range. This is done based on the advice from Marc
Zyngier http://www.spinics.net/lists/arm-kernel/msg483139.html
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a single r8a7795 INTC-EX device node to support
external IRQ pins IRQ0 -> IRQ5.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Cortex-A53 L2 cache-controller.
The L2 cache for the Cortex-A53 CPU cores is 512 KiB large (organized as
32 KiB x 16 ways).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the missing "cache-unified" and "cache-level" properties to the
Cortex-A57 cache-controller node.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use GIC_* defines for GIC interrupt cells in r8a7795 device tree.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instead of using the generic armv8-pmuv3 compatibility use the more
specific Cortex A57 compatibility.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add device nodes for the L2 caches, and link the CPU node to its L2
cache node.
The L2 cache for the Cortex-A57 CPU cores is 2 MiB large (organized as
128 KiB x 16 ways).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
This increases the range and accuracy of supported baud rates:
- SCIF:
- Supports now 50, 230400, 460800, 500000, and 921600 bps,
- Perfect match for standard 50-460800, and 9216000 bps.
- HSCIF:
- Supports now 50, 75, and 110 bps,
- Perfect match for standard 50-460800, and 9216000 bps.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device node for the external SCIF_CLK.
The presence of the SCIF_CLK crystal and its clock frequency depend on
the actual board.
Add the two optional clock sources (S3D1 and SCIF_CLK for the internal
resp. external clock) for the Baud Rate Generator for External Clock
(BRG) to all SCIF and HSCIF device nodes.
This increases the range and accuracy of supported baud rates on
(H)SCIF.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The clock is really the device functional clock, not the interface
clock. Rename it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Complete the dma-controller nodes for SYS-DMAC 0 to 2.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SATA clock is 815, not 915.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables SATA device in r8a7795-salvator-x.dts.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds SATA device node to r8a7795.dtsi.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
[uli: adjusted for new MSTP clock scheme]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add Cortex-A57 CPU cores to r8a7795 SoC for a total of 4 x Cortex-A57.
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Sigend-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add PSCI node for r8a7795 SoC, and cpu node enable-method property is
set to "psci".
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
CS2000 needs AUDIO_CLKOUT as master clock which is generated
by Renesas sound, and Renesas sound needs CS2000 as ADUIO_CLK_B.
Because of this relationship, it will be dead-lock when driver probe.
cs2000: clk_multiplier@4f {
...
clocks = <&rcar_sound 0>, <&x12_clk>;
...
};
&rcar_sound {
...
assigned-clocks = <&cs2000>;
...
};
This patch is using dummy audio_clkout to avoid this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds PIO sound support for Salvator-X board.
It can use 44.1kHz base sound only at this point, since 48kHz base
sound needs CS2000, but it is not yet upstreamed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds SSI for PIO sound support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all HSCIF serial ports, incl. clocks, clock
domain, and dma properties.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add an ethernet0 alias for the wired network card so that U-Boot can
find the device-node and add an appropriate "local-mac-address"
property.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As has been the practice for boards for 32bit ARM Renesas SoCs
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add initial board support for r8a7795 Salvator-X. At this point
only DEBUG0 and DEBUG1 serial ports are supported.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add dummy nodes for the 3 DMA controllers.
This allows to start describing DMA channels for DMA slaves now.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
