bootph-all as phase tag was added to dt-schema
(dtschema/schemas/bootph.yaml) to describe various node usage during
boot phases with DT. Add bootph-all for all nodes that are used in the
bootloader on Renesas R-Car SoCs.
All SoC require CPG clock and its input clock, RST Reset, PFC pin
control and PRR ID register access during all stages of the boot
process, those are marked using bootph-all property, and so is the SoC
bus node which contains these IP.
Each board console UART is also marked as bootph-all to make it
available in all stages of the boot process.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250209180616.160253-2-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Current sound comment is indicating that #sound-dai-cells is required,
but it is needed only if board is using "simple-card".
Hence tidy up the comments.
As ulcb.dtsi and salvator-common.dtsi are already using "audio-graph",
the unneeded #sound-dai-cells are removed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87cz7ji418.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas R-Car CAN-FD Controller on R-Car Gen3 and RZ/G2 SoCs has two
interrupts. Add interrupt-names properties to all CAN-FD device nodes
to identify the individual interrupts, so we can make this property a
required property in the DT bindings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/10eef1e20372af4a156b06df8e5124666ec7c6b6.1651512451.git.geert+renesas@glider.be
Endpoints node must have a remote-endpoint property, as endpoints only
exist to model a link between ports. Drop the empty rgb output endpoints
from SoC dtsi files, and declare them in the board dts instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20220424161228.8147-2-laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Endpoints node must have a remote-endpoint property, as endpoints only
exist to model a link between ports. Drop the empty lvds endpoints from
SoC dtsi files, they should be instead declared in the board dts or in
overlays.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20220424161228.8147-1-laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add device nodes for the SPI Multi I/O Bus Controllers (RPC-IF) on the
various R-Car Gen3 SoCs that do not have support for them yet in their
device trees (R-Car H3, M3-W, M3-W+, M3-N, E3, and D3).
Based on patches in the BSP by Valentine Barshak.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/3231749c7b63df1a2134daabe66446a3e0e5515b.1648548339.git.geert+renesas@glider.be
The bindings have been updated to support two clocks.
Add a clock-names list in the device tree with fck in it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210224115146.9131-3-aford173@gmail.com
[geert: Update new r8a779a0.dtsi]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add device nodes for the Compare Match Timer (CMT) on the Renesas R-Car
M3-W+ (r8a77961) and D3 (r8a77995) SoCs.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20201209200738.811173-2-niklas.soderlund+renesas@ragnatech.se
[geert: squashed two commits]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Some EtherAVB variants support internal clock delay configuration, which
can add larger delays than the delays that are typically supported by
the PHY (using an "rgmii-*id" PHY mode, and/or "[rt]xc-skew-ps"
properties).
Historically, the EtherAVB driver configured these delays based on the
"rgmii-*id" PHY mode. This was wrong, as these are meant solely for the
PHY, not for the MAC. Hence properties were introduced for explicit
configuration of these delays.
Convert the R-Car Gen3 DTS files from the old to the new scheme:
- Add default "rx-internal-delay-ps" and "tx-internal-delay-ps"
properties to the SoC .dtsi files, to be overridden by board files
where needed,
- Convert board files from "rgmii-*id" PHY modes to "rgmii", adding
the appropriate "rx-internal-delay-ps" and/or "tx-internal-delay-ps"
overrides.
Notes:
- R-Car E3 and D3 do not support TX internal delay handling,
- On R-Car D3, TX internal delay handling must always be enabled,
hence this fixes a bug on Draak,
- On R-Car V3H, RX internal delay handling must always be enabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200819134344.27813-7-geert+renesas@glider.be
According to Devicetree Specification v0.2 and later, Section "Generic
Names Recommendation", the node name for a pin controller device node
should be "pinctrl".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200821112433.5652-1-geert+renesas@glider.be
Add reset control properties to the device nodes for the Display Units
on all supported R-Car Gen3 SoCs. Note that on these SoCs, there is
only a single reset for each pair of DU channels.
The display nodes on R-Car V3M and V3H already had "resets" properties,
but lacked the corresponding "reset-names" properties.
Join the clocks lines while at it, to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200218133019.22299-4-geert+renesas@glider.be
Add device nodes for the CryptoCell instances on the various Renesas
R-Car Gen3 SoCs that do not have support for them yet in their device
trees (M3-W, M3-W+, M3-N, E3, D3).
The R-Car H3 device tree already supports this device.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200124133330.16121-1-geert+renesas@glider.be
The Renesas-specific "vsps" property lacks a vendor prefix.
Add a "renesas," prefix to comply with DT best practises.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20191105183504.21447-4-geert+renesas@glider.be
To improve human readability and enable automatic validation, the tuples
in the various properties containing interrupt specifiers should be
grouped. While "make dtbs_check" does not impose this yet for the
"interrupts" property, it does for the "interrupt-map" property.
Fix this by grouping the tuples of the "interrupts" and "interrupt-map"
properties using angle brackets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191213164115.3697-7-geert+renesas@glider.be
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Add CMM units to Renesas R-Car Gen3 SoC that support it, and reference them
from the Display Unit they are connected to.
Sort the 'vsps', 'renesas,cmm' and 'status' properties in the DU unit
consistently in all the involved DTS.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Link: https://lore.kernel.org/r/20191016085548.105703-8-jacopo+renesas@jmondi.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Update the 'vsps' property in the R-Car Gen3 SoC device tree files to
match what's in the documentation example.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Since the R8A77995 SoC uses DU{0,1}, the range from the base address to
the 0x4000 address is used.
This patch fixed it.
Fixes: 18f1a773e3 ("arm64: dts: renesas: r8a77995: add DU support")
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add CPG reset properties to DU node of D3 (r8a77995) SoC.
According to Laurent Pinchart, R-Car Gen3 reset is handled at the group
level so specifying one reset entry per group is sufficient.
This patch was inspired by a patch in the BSP by
Takeshi Kihara <takeshi.kihara.df@renesas.com>.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the new renesas,companion property to the LVDS0 node to point to the
companion LVDS encoder LVDS1.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since the commit 233da2c9ec ("dt-bindings: phy: rcar-gen3-phy-usb2:
Revise #phy-cells property") revised the #phy-cells, this patch follows
the updated document for R-Car Gen3 and RZ/A2 SoCs.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The 'arm,armv8' compatible string is only for software models. It adds
little value otherwise and is inconsistently used as a fallback on some
platforms. Remove it from those platforms.
This fixes warnings generated by the DT schema.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Chanho Min <chanho.min@lge.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds/enables USB2.0 peripheral for R-Car [DE]3 boards.
R-Car E3 Ebisu board connects the ID pin to the SoC, so this adds
a group "usb0_id" into usb0_pins node. Also, to use SW15 pin 3 side,
this patch adds vbus0_usb2 node on r8a77990-ebisu.dts.
R-Car D3 Draak board doesn't connect the ID pin, so this adds
"renesas,no-otg-pins" property into usb2_phy0 node.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a77995 D3 platform has 2 LVDS channels connected to the DU.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
[uli: moved lvds* into the soc node, added PM domains, resets]
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car Gen3 SoCs need to enable/deassert clocks/resets of both usb 2.0
host (included phy) and peripheral. Otherwise, other side device
cannot work correctly. So, this patch revises properties of clocks
and resets. After that, each device driver can enable/deassert
clocks/resets by its self.
Notes:
- To work the renesas_usbhs driver correctly when host side drivers
are disabled and the renesas_usbhs driver doesn't have multiple
clock management, this patch doesn't change the order of the clocks
property in each hsusb node.
- This patch doesn't have any side-effects even if the renesas_usbhs
driver doesn't have reset_control and multiple clock management.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up SYS-DMAC0, SYS-DMAC1 and SYS-DMAC2 to IPMMU-DS0 and IPMMU-DS1
following the R-Car Gen3 Rev.1.00 (April 2018) datasheet.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Browsing the DTS for all the R-Car SoCs with similar part numbers
makes my head hurt, so to improve the user friendliness of the
DTS code base include R-Car product name in each DTSI file.
Product names are derived from
Documentation/devicetree/bindings/arm/shmobile.txt
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the device nodes for SCIF {0,1,3,4,5} and all HSCIF serial
ports, incl. clocks, power domain and DMAs.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The VSPD and FCPVD nodes have overlapping register ranges, as the FCPVD
devices are mapped in the memory range usually used by the VSP LUT and
CLU, which are not present in the VSPD. Fix this by shortening the VSPD
registers range to 0x5000.
Fixes: 9f8573e38a ("arm64: dts: renesas: r8a7795: Add VSP instances")
Fixes: 291e0c4994 ("arm64: dts: r8a7795: Add support for R-Car H3 ES2.0")
Fixes: f06ffdfbdd ("arm64: dts: r8a7796: Add VSP instances")
Fixes: b4f92030d5 ("arm64: dts: renesas: r8a77970: add VSPD support")
Fixes: 295952a183 ("arm64: dts: renesas: r8a77995: add VSP instances")
Fixes: 85cb322921 ("arm64: dts: renesas: r8a77965: Add VSP instances")
Reported-by: Simon Horman <horms+renesas@verge.net.au>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The compat string renesas,gpio-rcar has been deprecated since v4.14,
the same release that r8a77990 SoC support was added. Thus
renesas,gpio-rcar can safely be removed without any risk of behaviour
changes between old and new mainline kernels and DTBs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add power domain information to the R-Car D3 IPMMU device nodes.
As specified by the data sheet, all the IPMMU devices are always on.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove 'status = "disabled"' to make sure all IPMMU devices are enabled
in DT on the r8a77995 SoC.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: rebased]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sort subnodes of the soc node.
- The primary key is the bus address.
- The secondary key is the IP block.
- The tertiary key is the node name.
This is part of an ongoing effort to provide consistent node
order in the DT of Renesas SoCs to improve maintainability.
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sort subnodes of the root node alphanumerically.
This is part of an ongoing effort to provide consistent node
order in the DT of Renesas SoCs to improve maintainability.
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
