The I2C EEPROM U197 on Condor is also present on Condor-I, but it was
moved to the other side of the bi-directional voltage-level translator
on I2C bus zero, and relabeled to U230.
Move it to condor-common.dtsi to make it available on Condor-I, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/33a1ec9ee8fff7708f699c668d7399fde2b46553.1716455483.git.geert+renesas@glider.be
We have V3H Condor board, and will have V3H2 Condor-I board.
This patch adds condor-common.dtsi to share the common settings
between these boards.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/871qsy625m.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
I2C aliases are not a property of a SoC. They belong to board files
where they are named accordingly in the schematics.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220825071022.7864-4-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the MAX9286 GMSL deserializers on Condor-V3H board.
Connected cameras should be defined in a device-tree overlay or included
after these definitions.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20211216163439.139579-5-jacopo+renesas@jmondi.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add compatible values to Ethernet PHY subnodes representing Micrel
KSZ9031 PHYs on R-Car Gen3 boards. This allows software to identify the
PHY model at any time, regardless of the state of the PHY reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/07bd7e04dda9e84cde0664980f0b1a6d69e03109.1631174218.git.geert+renesas@glider.be
Make sure the R-Car Gen3 SoC model present is documented in the comment
header of each board DTS, on a single line. This makes it easier to
identify boards that are available with different SoC or SiP options.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/251569665d7d4f4ed4bbab7267ce2ddccdef33e5.1626261816.git.geert+renesas@glider.be
The eMMC card has two supplies, VCC and VCCQ. The VCC supplies the NAND
array and the VCCQ supplies the bus. On Condor, the VCC is connected to
3.3V rail, while the VCCQ is connected to 1.8V rail. Adjust the pinmux
to match the bus, which is always operating in 1.8V mode.
While at it, deduplicate the pinmux entries, which are now the same for
both default and UHS modes. We still need the two pinctrl entries to
match the bindings though.
Thanks to Marek Vasut for this description from commit 5f65328df3
("arm64: dts: renesas: Switch eMMC bus to 1V8 on Salvator-X and ULCB").
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210419143858.39401-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Some SDHI instances are solely used for eMMC. Disable SD and SDIO
for faster initialization.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adam Ford <aford173@gmail.com> (beacon)
Link: https://lore.kernel.org/r/20210119133322.87289-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Define the Condor/V3HSK board dependent parts of the RPC-IF device node.
Add device nodes for Spansion S25FS512S SPI flash and MTD partitions on it.
Based on the original patches by Dmitry Shifrin.
Signed-off-by: Dmitry Shifrin <dmitry.shifrin@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Link: https://lore.kernel.org/r/322ca212-a45f-cd2c-f1eb-737f0aa42d22@cogentembedded.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Small fixes to make these DTs compliant with the adi,adv7511w binding.
r8a77970-eagle.dts,
r8a77970-v3msk.dts,
r8a77980-condor.dts,
r8a77980-v3hsk.dts,
r8a77990-ebisu.dts:
Remove the adi,input-style and adi,input-justification properties.
r8a77995-draak.dts:
Reorder the I2C slave addresses of the hdmi-encoder@39 node and
remove the adi,input-style and adi,input-justification properties.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200511110611.3142-2-ricardo.canuelo@collabora.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The "official" Condor boards have always been wired to mount NFS via
GEther, not EtherAVB -- the boards resoldered for EtherAVB were local
to Cogent Embedded, so we've been having an unpleasant situation where
a "normal" Condor board still can't mount NFS (unless an EtherAVB PHY
extension board is plugged in). Switch from EtherAVB to GEther at last!
Fixes: 8091788f3d ("arm64: dts: renesas: condor: add EtherAVB support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable PCIe PHY and PCIEC and specify the PCIe bus clock for the Condor
board.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Condor/V3HSK board dependent parts of the DU and LVDS device
nodes. Also add the device nodes for Thine THC63LVD1024 LVDS decoder and
Analog Devices ADV7511W HDMI transmitter...
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe RWDT in the R8A77980 SoC device tree.
Enable RWDT on the Condor and V3H Starter Kit boards.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specify Ethernet PHY IRQs in the Condor/V3HSK board device trees, now that
we have the GPIO support (previously phylib had to resort to polling).
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Condor board dependent part of the I2C0 device node.
The I2C0 bus is populated by 2 ON Semiconductor PCA9654 I/O expanders
and Analog Devices ADV7511W HDMI transmitter (but we're only describing
the former chips now).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Condor board dependent part of the CAN-FD device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Condor board dependent part of the MMC0 (connected to eMMC chip)
device node along with the necessary voltage regulators...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the (previously omitted) EtherAVB pin data to the Condor board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the (previously omitted) SCIF0 pin data to the Condor board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Condor board dependent part of the EtherAVB device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A77980 SoC based Condor board.
The board has 1 debug serial port (SCIF0); include support for it, so
that the serial console can work.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: correct memory size to 0x78000000 (2GiB)]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
