bootph-all as phase tag was added to dt-schema
(dtschema/schemas/bootph.yaml) to describe various node usage during
boot phases with DT. Add bootph-all for all nodes that are used in the
bootloader on Renesas RZ/G2 SoCs.
All SoC require CPG clock and its input clock, RST Reset, PFC pin
control and PRR ID register access during all stages of the boot
process, those are marked using bootph-all property, and so is the SoC
bus node which contains these IP.
Each board console UART is also marked as bootph-all to make it
available in all stages of the boot process.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250209180616.160253-3-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add iommu-map and iommu-map-mask properties to the PCIe host nodes.
Note that iommu-map-mask should be zero because the IPMMU assigns
one micro TLB ID only, to the PCIe host.
Also change the dma-ranges arguments for IOMMU. Note that dma-ranges
can be used if the IOMMU is disabled.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230510090358.261266-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Current sound comment is indicating that #sound-dai-cells is required,
but it is needed only if board is using "simple-card".
Hence tidy up the comments.
As ulcb.dtsi and salvator-common.dtsi are already using "audio-graph",
the unneeded #sound-dai-cells are removed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87cz7ji418.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
With 'unevaluatedProperties' support implemented, there are a number of
warnings when running dtbs_check:
arch/arm64/boot/dts/renesas/r8a774b1-hihope-rzg2n-rev2-ex-idk-1110wr.dtb: spi@ee200000: Unevaluated properties are not allowed ('clock-names' was unexpected)
From schema: Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml
The main problem is that the DT bindings do not allow clock-names.
So just drop the clock-names properties from the SoC DTSI files.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220829215128.5983-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas R-Car CAN-FD Controller on R-Car Gen3 and RZ/G2 SoCs has two
interrupts. Add interrupt-names properties to all CAN-FD device nodes
to identify the individual interrupts, so we can make this property a
required property in the DT bindings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/10eef1e20372af4a156b06df8e5124666ec7c6b6.1651512451.git.geert+renesas@glider.be
Endpoints node must have a remote-endpoint property, as endpoints only
exist to model a link between ports. Drop the empty rgb output endpoints
from SoC dtsi files, and declare them in the board dts instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20220424161228.8147-2-laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Endpoints node must have a remote-endpoint property, as endpoints only
exist to model a link between ports. Drop the empty lvds endpoints from
SoC dtsi files, they should be instead declared in the board dts or in
overlays.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20220424161228.8147-1-laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The binding node names for the thermal zones are not successfully
validated by the dt-schemas.
Fix the validation by changing from sensor-thermalN or thermal-sensor-N
to sensorN-thermal. Provide node labels of the form sensorN_thermal to
ensure consistency with the other platform implementations.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20211104224033.3997504-1-kieran.bingham+renesas@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The bindings have been updated to support two clocks.
Add a clock-names list in the device tree with fck in it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210224115146.9131-3-aford173@gmail.com
[geert: Update new r8a779a0.dtsi]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The port@0 is a mandatory port, add or move the declaration to the CSI-2
nodes top declared in dtsi files instead of depending on dts files
adding them when describing the external connection.
This fixes validation warnings for DTB outputs that do not connect all
CSI-2 receivers to transmitters and thus declaring all port@0 nodes in
dts files.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20210421150221.3202955-3-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/G2 series contain the SPI Multi I/O Bus Controller (RPC-IF).
Add the nodes, but make them disabled by default.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20210102115412.3402059-4-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Per the reference manual for the RZ/G Series, 2nd Generation,
the RZ/G2M, RZ/G2N, and RZ/G2H have a bit that can be set to
choose between a crystal oscillator and an external oscillator.
Because only boards that need this should enable it, it's marked
as disabled by default for backwards compatibility with existing
boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201228202221.2327468-2-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Some EtherAVB variants support internal clock delay configuration, which
can add larger delays than the delays that are typically supported by
the PHY (using an "rgmii-*id" PHY mode, and/or "[rt]xc-skew-ps"
properties).
Historically, the EtherAVB driver configured these delays based on the
"rgmii-*id" PHY mode. This was wrong, as these are meant solely for the
PHY, not for the MAC. Hence properties were introduced for explicit
configuration of these delays.
Convert the RZ/G2 DTS files from the old to the new scheme:
- Add default "rx-internal-delay-ps" and "tx-internal-delay-ps"
properties to the SoC .dtsi files, to be overridden by board files
where needed,
- Convert board files from "rgmii-*id" PHY modes to "rgmii", adding
the appropriate "rx-internal-delay-ps" and/or "tx-internal-delay-ps"
overrides.
Notes:
- RZ/G2E does not support TX internal delay handling.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200819134344.27813-8-geert+renesas@glider.be
According to Devicetree Specification v0.2 and later, Section "Generic
Names Recommendation", the node name for a pin controller device node
should be "pinctrl".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200821112433.5652-1-geert+renesas@glider.be
Add support for HiHope RZ/G2N Rev.3.0/4.0 main board support based on
r8a774b1 SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Link: https://lore.kernel.org/r/1593004330-5039-10-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add reset control properties to the device nodes for the Display Units
on all supported RZ/G2 SoCs. Note that on these SoCs, there is only a
single reset for each pair of DU channels.
Join the clocks lines while at it, to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200218133019.22299-5-geert+renesas@glider.be
The Renesas-specific "vsps" property lacks a vendor prefix.
Add a "renesas," prefix to comply with DT best practises.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20191105183504.21447-4-geert+renesas@glider.be
To improve human readability and enable automatic validation, the tuples
in the "ranges" and "dma-ranges" properties of PCI device nodes should
be grouped.
Fix this by grouping the tuples of the "ranges" and "dma-ranges"
properties using angle brackets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191213164115.3697-8-geert+renesas@glider.be
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
To improve human readability and enable automatic validation, the tuples
in the various properties containing interrupt specifiers should be
grouped. While "make dtbs_check" does not impose this yet for the
"interrupts" property, it does for the "interrupt-map" property.
Fix this by grouping the tuples of the "interrupts" and "interrupt-map"
properties using angle brackets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191213164115.3697-7-geert+renesas@glider.be
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Hook up r8a774b1 DMAC nodes to the IPMMUs. In particular SYS-DMAC0
gets tied to IPMMU-DS0, and SYS-DMAC1 and SYS-DMAC2 get tied to IPMMU-DS1.
Based on work for the r8a7796 by Magnus Damm.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Link: https://lore.kernel.org/r/1569313375-53428-7-git-send-email-biju.das@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
