Use the more concise interrupts-extended property to fully describe the
interrupts.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> # G2L family and G3S
Link: https://lore.kernel.org/e9db8758d275ec63b0d6ce086ac3d0ea62966865.1728045620.git.geert+renesas@glider.be
Add compatible values to Ethernet PHY subnodes representing Realtek
RTL8211E PHYs on RZ/G2 boards. This allows software to identify the PHY
model at any time, regardless of the state of the PHY reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/3b366e3dddd4d3cd7e89b92d3a8f78f6dc18e244.1631174218.git.geert+renesas@glider.be
Hihope boards use Realtek PHY. From the very beginning it use only
tx delays. However the phy driver commit bbc4d71d63
("net: phy: realtek: fix rtl8211e rx/tx delay config") introduced
NFS mount failure. Now it needs rx delay inaddition to tx delay
for NFS mount to work. This patch fixes NFS mount failure issue
by adding MAC internal rx delay.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Fixes: bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx delay config")
Link: https://lore.kernel.org/r/20210721180632.15080-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Some EtherAVB variants support internal clock delay configuration, which
can add larger delays than the delays that are typically supported by
the PHY (using an "rgmii-*id" PHY mode, and/or "[rt]xc-skew-ps"
properties).
Historically, the EtherAVB driver configured these delays based on the
"rgmii-*id" PHY mode. This was wrong, as these are meant solely for the
PHY, not for the MAC. Hence properties were introduced for explicit
configuration of these delays.
Convert the RZ/G2 DTS files from the old to the new scheme:
- Add default "rx-internal-delay-ps" and "tx-internal-delay-ps"
properties to the SoC .dtsi files, to be overridden by board files
where needed,
- Convert board files from "rgmii-*id" PHY modes to "rgmii", adding
the appropriate "rx-internal-delay-ps" and/or "tx-internal-delay-ps"
overrides.
Notes:
- RZ/G2E does not support TX internal delay handling.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200819134344.27813-8-geert+renesas@glider.be
HiHope RZG2[HMN] boards uses Realtek phy and the driver does not support
rxc-skew-ps property. So remove rxc-skew-ps from ethernet-phy node.
Fixes: 7433f1fb8e ("arm64: dts: renesas: Add HiHope RZ/G2M sub board support")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20201015132350.8360-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The HiHope RZ/G2H sub board sits below the HiHope RZ/G2H main board.
These boards are identical with the ones for RZ/G2M[N].
Signed-off-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/1594230511-24790-9-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Separate out LVDS specific nodes into common file
hihope-rzg2-ex-lvds.dtsi so that this can be re-used by RZ/G2M[N]
variants.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Link: https://lore.kernel.org/r/1593004330-5039-8-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The plan for the HiHope RZ/G2N board is to enable pciec0 by default,
and use pciec1 physical interface for SATA (as SATA and PCIE1 share
the same physical interface), therefore move pciec1 enabling away
from hihope-rzg2-ex.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Link: https://lore.kernel.org/r/1570178133-21532-8-git-send-email-fabrizio.castro@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch enables both CAN0 and CAN1, both exposed via
connectors found on the expansion board.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch enables PCIEC[01] PCI express controller on the sub board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The HiHope RZ/G2M sub board sits below the HiHope RZ/G2M main board.
This patch also adds ethernet support along with a dtsi common to
both HiHope RZ/G2M and RZ/G2N sub boards.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
