Add DT entries for the sm8650 iris decoder.
Since the firmware is required to be signed, only enable
on Qualcomm development boards where the firmware is
available.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250613-topic-sm8x50-upstream-iris-8650-dt-v4-1-35ea7952f2d2@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add QMP handle which is used to send QMP command to always on processor
to populate DDR stats. Add QMP handle for SM8450/SM8550/SM8650/SM8750.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Maulik Shah <maulik.shah@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250611-ddr_stats_-v5-3-24b16dd67c9c@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Only two little a520s share the same L2, every a720 has their own L2
cache.
Fixes: d235037799 ("arm64: dts: qcom: add initial SM8650 dtsi")
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250405105529.309711-1-mitltlatltl@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use allocated region size for VBIF regions as defined by the docs
(0x3000) instead of just using the last register address.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-20-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-24-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On SM8650 the CPUs 0-1 are "silver" (Cortex-A520), CPU 2-6 are "gold"
(Cortex-A720) and CPU 7 is "gold-plus" (Cortex-X4).
So reference the correct "gold" idle-state for CPU core 2.
Fixes: d235037799 ("arm64: dts: qcom: add initial SM8650 dtsi")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250314-sm8650-cpu2-sleep-v1-1-31d5c7c87a5d@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The PMUs shares the same per-cpu (PPI) interrupt, so declare the proper
interrupt partition maps and use the 4th interrupt cell to pass the
partition phandle for each ARM PMU node.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250228-topic-sm8650-pmu-ppi-partition-v4-2-78cffd35c73d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The ARM PMUs shares the same per-cpu (PPI) interrupt, so we need to switch
to interrupt-cells = <4> in the GIC node to allow adding an interrupt
partition map phandle as the 4th cell value for GIC_PPI interrupts.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250228-topic-sm8650-pmu-ppi-partition-v4-1-78cffd35c73d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Only CPU0 Embedded Trace Extension (ETE) was added, but there's one
for all 8 CPUs, so add the missing ones.
Fixes: 256e6937e4 ("arm64: dts: qcom: sm8650: Add coresight nodes")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250227-topic-sm8650-upstream-add-all-coresight-cpus-v3-1-48ae516be0d5@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The bindings requires the mdp0-mem and the cpu-cfg interconnect path,
add the missing cpu-cfg path to fix the dtbs check error and also to ensure
that MDSS has enough bandwidth to let HLOS write config registers.
Fixes: 9fa33cbca3 ("arm64: dts: qcom: sm8650: correct MDSS interconnects")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250227-topic-sm8x50-mdss-interconnect-bindings-fix-v5-2-bf6233c6ebe5@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Swich to an OPP table for the UFS frequency scaling instead of
the deprecated freq-table-hz property.
The Operating Point table will also provide the associated
power domain level.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250115-topic-sm8x50-upstream-dt-icc-update-v1-10-eaa8b10e2af7@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The QUP Serial Engines requires different power domain level
depending on their working frequency, add the required OPP
table with the level associated with all possible frequencies.
For the "I2C Hub" serial engines, sinse they only support a
single Operating Point, only add a single power domain level
property.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250115-topic-sm8x50-upstream-dt-icc-update-v1-9-eaa8b10e2af7@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The PCIe bus interconnect path can be scaled depending on the
PCIe link established, add the OPP table with all the possible
link speeds and the associated power domain level.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250115-topic-sm8x50-upstream-dt-icc-update-v1-8-eaa8b10e2af7@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
In all interconnect paths involving the cpu (MASTER_APPSS_PROC), use
the QCOM_ICC_TAG_ACTIVE_ONLY which will only retain the vote if
the CPU is online, leaving the firmware disabling the path when the
CPUs goes in suspend-idle.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250115-topic-sm8x50-upstream-dt-icc-update-v1-6-eaa8b10e2af7@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Remove the remaining polling-delay-passive properties from
thermal nodes without a passive trip point.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250203-topic-sm8650-thermal-cpu-idle-v4-4-65e35f307301@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
While the CPUs thermal is handled by the LMH, and GPU has a passive
cooldowm via the HLOS DCVS, all the other thermal blocks only have
hot and critical and no passive/active trip points.
Passive or active thermal management for those blocks should
be either defined if somehow we can express those in DT or
in the board definition if there's an active cooling device
available.
The tsens MAX_THRESHOLD is set to 120C on those platforms, so set
the hot to 110C to leave a chance to HLOS to react and critical to
115C to avoid the monitor thermal shutdown.
In the case a passive or active cooling device would be
available, the downstream reference implementation uses
the 95C "tj" trip point, as we already use for the
gpuss thermal blocks.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250203-topic-sm8650-thermal-cpu-idle-v4-3-65e35f307301@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On the SM8650, the dynamic clock and voltage scaling (DCVS) for the GPU
is done from the HLOS, but the GPU can achieve a much higher temperature
before failing according the reference downstream implementation.
Set higher temperatures in the GPU trip points corresponding to
the temperatures provided by Qualcomm in the dowstream source, much
closer to the junction temperature and with a higher critical
temperature trip in the case the HLOS DCVS cannot handle the
temperature surge.
The tsens MAX_THRESHOLD is set to 120C on those platforms, so set
the hot to 110C to leave a chance to HLOS to react and critical to
115C to avoid the monitor thermal shutdown.
Fixes: 497624ed55 ("arm64: dts: qcom: sm8650: Throttle the GPU when overheating")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250203-topic-sm8650-thermal-cpu-idle-v4-2-65e35f307301@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On the SM8650, the dynamic clock and voltage scaling (DCVS) is done in an
hardware controlled loop using the LMH and EPSS blocks with constraints and
OPPs programmed in the board firmware.
Since the Hardware does a better job at maintaining the CPUs temperature
in an acceptable range by taking in account more parameters like the die
characteristics or other factory fused values, it makes no sense to try
and reproduce a similar set of constraints with the Linux cpufreq thermal
core.
In addition, the tsens IP is responsible for monitoring the temperature
across the SoC and the current settings will heavily trigger the tsens
UP/LOW interrupts if the CPU temperatures reaches the hardware thermal
constraints which are currently defined in the DT. And since the CPUs
are not hooked in the thermal trip points, the potential interrupts and
calculations are a waste of system resources.
Drop the current passive trip points and only leave the critical trip
point that will trigger a software system reboot before an hardware
thermal shutdown in the allmost impossible case the hardware DCVS cannot
handle the temperature surge.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20250203-topic-sm8650-thermal-cpu-idle-v4-1-65e35f307301@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the OPP tables for each CPU clusters (cpu0-1, cpu2-3-4, cpu5-6 & cpu7)
to permit scaling the Last Level Cache Controller (LLCC), DDR and L3 cache
frequency by aggregating bandwidth requests of all CPU core with referenc
to the current OPP they are configured in by the LMH/EPSS hardware.
The effect is a proper caches & DDR frequency scaling when CPU cores
changes frequency.
The OPP tables were built using the downstream memlat ddr, llcc & l3
tables for each cluster types with the actual EPSS cpufreq LUT tables
from running HDK and QRD devices.
The cpu2 and cpu5 tables are similar but must be kept separate to
take in account that they define OPP for shared CPUs of two different
clusters that can scale separately, thus vote different bandwidths.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250211-topic-sm8650-ddr-bw-scaling-v2-3-a0c950540e68@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the interconnect entry for each cpu, with 3 different paths:
- CPU to Last Level Cache Controller (LLCC)
- Last Level Cache Controller (LLCC) to DDR
- L3 Cache from CPU to DDR interface
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250211-topic-sm8650-ddr-bw-scaling-v2-2-a0c950540e68@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Qcom PCIe RC controllers are capable of generating 'global' SPI interrupt
to the host CPUs. This interrupt can be used by the device driver to
identify events such as PCIe link specific events, safety events, etc...
Hence, add it to the PCIe RC node along with the existing MSI interrupts.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241126-topic-sm8x50-pcie-global-irq-v1-3-4049cfccd073@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The address space in MPSS/Modem PAS (Peripheral Authentication Service)
remoteproc node should point to the QDSP PUB address space
(QDSP6...SS_PUB) which has a length of 0x10000. Value of 0x4040 was
copied from older DTS, but it grew since then.
This should have no functional impact on Linux users, because PAS loader
does not use this address space at all.
Fixes: 10e0246712 ("arm64: dts: qcom: sm8650: add interconnect dependent device nodes")
Cc: stable@vger.kernel.org
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241213-dts-qcom-cdsp-mpss-base-address-v3-12-2e0036fccd8d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The address space in CDSP PAS (Peripheral Authentication Service)
remoteproc node should point to the QDSP PUB address space
(QDSP6...SS_PUB) which has a length of 0x10000. Value of 0x1400000 was
copied from older DTS, but it does not look accurate at all.
This should have no functional impact on Linux users, because PAS loader
does not use this address space at all.
Fixes: 10e0246712 ("arm64: dts: qcom: sm8650: add interconnect dependent device nodes")
Cc: stable@vger.kernel.org
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241213-dts-qcom-cdsp-mpss-base-address-v3-11-2e0036fccd8d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The address space in ADSP PAS (Peripheral Authentication Service)
remoteproc node should point to the QDSP PUB address space
(QDSP6...SS_PUB): 0x0680_0000 with length of 0x10000.
0x3000_0000, value used so far, is the main region of CDSP. Downstream
DTS uses 0x0300_0000, which is oddly similar to 0x3000_0000, yet quite
different and points to unused area.
Correct the base address and length, which also moves the node to
different place to keep things sorted by unit address. The diff looks
big, but only the unit address and "reg" property were changed. This
should have no functional impact on Linux users, because PAS loader does
not use this address space at all.
Fixes: 10e0246712 ("arm64: dts: qcom: sm8650: add interconnect dependent device nodes")
Cc: stable@vger.kernel.org
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241213-dts-qcom-cdsp-mpss-base-address-v3-10-2e0036fccd8d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
There is a mismatch between 'reg' property and unit address for last
there CDSP compute context banks. Current values were taken as-is from
downstream source. Considering that 'reg' is used by Linux driver as
SID of context bank and that least significant bytes of IOMMU value
match the 'reg', assume the unit-address is wrong and needs fixing.
This also won't have any practical impact, except adhering to Devicetree
spec.
Fixes: dae8cdb0a9 ("arm64: dts: qcom: sm8650: Add three missing fastrpc-compute-cb nodes")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20241104144204.114279-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
SM8650 lists two interconnects for the display subsystem, mdp0-mem
(between MDP and LLCC) and mdp1-mem (between LLCC and EBI, memory).
The second interconnect is a misuse. mdpN-mem paths should be used for
several outboud MDP interconnects rather than the path between LLCC and
memory. This kind of misuse can result in bandwidth underflows, possibly
degrading picture quality as the required memory bandwidth is divided
between all mdpN-mem paths (and LLCC-EBI should not be a part of such
division).
Drop the second path and use direct MDP-EBI path for mdp0-mem until we
support separate MDP-LLCC and LLCC-EBI paths.
Fixes: 10e0246712 ("arm64: dts: qcom: sm8650: add interconnect dependent device nodes")
Cc: stable@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241026-fix-sm8x50-mdp-icc-v2-2-fd8ddf755acc@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Each GPU OPP requires a specific peak DDR bandwidth, let's add
those to each OPP and also the related interconnect path.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241217-topic-sm8x50-gpu-bw-vote-v6-7-1adaf97e7310@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Devicetree binding has documented the node name for UFS controllers as
'ufshc'. So let's use it instead of 'ufs' which is for the UFS devices.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20240514-ufs-nodename-fix-v1-2-4c55483ac401@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
DTS coding style expects labels to be lowercase. No functional impact.
Verified with comparing decompiled DTB (dtx_diff and fdtdump+diff).
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241022-dts-qcom-label-v3-14-0505bc7d2c56@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The full register range for ICE on sm8650 is 0x18000 so update the
crypto node.
Reviewed-by: Om Prakash Singh <quic_omprsing@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Gaurav Kashyap <quic_gaurkash@quicinc.com>
Co-developed-by: Gaurav Kashyap <quic_gaurkash@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20241007-wrapped-keys-dts-v8-1-05ee041f2fc1@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Qualcomm SM8650 SoC has three CCI controllers with two I2C busses
connected to each of them.
The CCI controllers on SM8650 are compatible with the ones found on
many other older generations of Qualcomm SoCs.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20240612215835.1149199-5-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add device nodes for video and camera clock controllers on Qualcomm
SM8650 platform.
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240602114439.1611-9-quic_jkona@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Describe the ath12k WLAN on-board the WCN7850 module present on the
board.
[Neil: authored the initial version of the change]
Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240605122729.24283-3-brgl@bgdev.pl
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
There is no need to specify exact name for the second (AUX) output
clock. It has never been used for the lookups based on the system
clock name. The driver generates it on its own, in order to remain
compatible with the older DT. Drop the clock name.
Fixes: d00b42f170 ("arm64: dts: qcom: sm8650: remove pcie-1-phy-aux-clk and add pcie1_phy pcie1_phy_aux_clk")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240614-fix-pcie-phy-compat-v3-5-730d1811acf4@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add an 85C passive trip point to ensure the thermal framework takes
sufficient action to prevent reaching junction temperature and a
110C critical point to help avoid hw damage.
Also, register the GPU as a cooling device and hook it up to the
right thermal zones.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240510-topic-gpus_are_cool_now-v1-12-ababc269a438@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Chipsets before SM8450 have only one broadcast register (Broadcast_OR)
which is used to broadcast writes and check for status bit 0 only in
all channels.
>From SM8450 onwards, a new Broadcast_AND region was added which checks
for status bit 1. This hasn't been updated and Broadcast_OR region
was wrongly being used to check for status bit 1 all along.
Hence mapping Broadcast_AND region's address space to LLCC in SM8650.
Signed-off-by: Unnathi Chalicheemala <quic_uchalich@quicinc.com>
Link: https://lore.kernel.org/r/3a8804b35f44485637398faa9c0bda76813fe4d7.1717014052.git.quic_uchalich@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Arm heterogeneous configurations should have separate PMU nodes for each
CPU uarch as the uarch specific events can be different. The
"arm,armv8-pmuv3" compatible is also intended for s/w models rather than
specific uarch implementations.
All the kryo CPUs are missing PMU compatibles, so they can't be fixed.
Signed-off-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20240417204247.3216703-1-robh@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable download mode setting for sm8650 which can help collect
ramdump for this SoC.
Signed-off-by: Mukesh Ojha <quic_mojha@quicinc.com>
Reviewed-by: Elliot Berman <quic_eberman@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/1715888133-2810-1-git-send-email-quic_mojha@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Qcom SoCs doesn't support legacy PCI, but only PCIe. So use the correct
node name for the controller instances.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240321-pcie-qcom-bridge-dts-v2-21-1eb790c53e43@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The PCIe Gen4x2 PHY found in the SM8650 SoCs have a second clock named
"PHY_AUX_CLK" which is an input of the Global Clock Controller (GCC) which
is muxed & gated then returned to the PHY as an input.
Remove the dummy pcie-1-phy-aux-clk clock and now the pcie1_phy exposes
2 clocks, properly add the pcie1_phy provided clocks to the Global Clock
Controller (GCC) node clocks inputs.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240502-topic-sm8x50-upstream-pcie-1-phy-aux-clk-v5-3-10c650cfeade@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The orientation-switch of the USB+DP QMP PHY is not a property of the
board, it is a design property of the QMP PHY itself. Move the property
from board DTS to SoC DTSI.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240429-usb-link-dtsi-v1-9-87c341b55cdf@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Move the graph connection between USB host, USB SS PHY and DP port to
the SoC dtsi file. They are linked in hardware in this way.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240429-usb-link-dtsi-v1-5-87c341b55cdf@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
