A platform display clock controller is expected to be enabled by default
for all boards, however in particular cases preset display clock setting
is expected. To avoid any probable regression before enabling display
clock controller for all SM8450 platforms disable it for SM8450 powered
Sony Xperia phones.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20240924100602.3813725-4-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Interrupt flags 0x2008 looks like some downstream copy-paste, because
generic GPIOLIB code, used by Qualcomm pin controller drivers, ignores
flags outside of IRQ_TYPE_SENSE_MASK. Probably the intention was to
pass just 0x8, so IRQ_TYPE_LEVEL_LOW.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org> # SM8450 PDX223
Link: https://lore.kernel.org/r/20240605160032.150587-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Since we have those defines available in a header, let's use them
everywhere where qcom,vmid property is used.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230818-qcom-vmid-defines-v1-1-45b610c96b13@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-10-krzysztof.kozlowski@linaro.org
Device node names should be generic and bindings expect certain pattern
for RPMh regulator nodes.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230127114347.235963-11-krzysztof.kozlowski@linaro.org
As much as it hurts me, there is no FM radio chips on these devices.
It seems to be present on Japanese models, but these are not available
globally and differ in a few more ways anyway (such as a super high-tech
NFC chip). Since it's the only subdevice of its I2C host bus, disable
said bus to save some power.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221213132517.203609-3-konrad.dybcio@linaro.org
Nagara devices use the Dialog SLG51000 PMIC for powering some camera
sensors. Add the required nodes to support it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221229103212.984324-7-konrad.dybcio@linaro.org
Set up gpio-controlled fixed regulators for camera on PDX223 and fix
up the existing ones in common and PDX224 trees.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221229103212.984324-5-konrad.dybcio@linaro.org
Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).
Add these to the PDX223&224 DTSIs to better document the hardware.
Diff between 223 and 224:
pm8350b
< "CAM_PWR_LD_EN",
> "NC",
pm8350c
< "RGBC_IR_PWR_EN",
> "NC",
Which is due to different camera power wiring on 223 and lack of a
ToF sensor on 224.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221229103212.984324-3-konrad.dybcio@linaro.org
Now that SPMI is finally in place, include the DTSIs of PMICs present
on Nagara.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221229103212.984324-2-konrad.dybcio@linaro.org
Add device node and required pinctrl settings (as well as a fixup for
an existing one, whoops!) to support the Samsung Electronics
touchscreen on Nagara devices.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221114095654.34561-4-konrad.dybcio@linaro.org
