There is no 'msg-size' property in ramoops, so assume intention was for
'pmsg-size':
sm6125-sony-xperia-seine-pdx201.dtb: ramoops@ffc00000: Unevaluated properties are not allowed ('msg-size' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230618114442.140185-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-7-krzysztof.kozlowski@linaro.org
Underscores should not be used in node names (dtc with W=2 warns about
them), so replace them with hyphens. In few places adjust the name to
match other nodes (e.g. xxx-regulator).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221214110448.86268-1-krzysztof.kozlowski@linaro.org
Enable I2C Serial Engines 1, 2 and 3 which are known to have hardware
connected to them, leaving the rest disabled to save on power. For
this, only GPI DMA 0 and QUP 0 need to be enabled, as nothing seems to
be connected to Serial Engines on GPU DMA 1 / QUP 1. Beyond this
downstream only defines a UART console available on Serial Engine 4
which also resides on QUP 0.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Martin Botka <martin.botka@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221216233408.1283581-4-marijn.suijten@somainline.org
- Remove autorepeat (leave key repetition to userspace);
- Remove unneeded status = "okay" (this is the default);
- Remove unneeded linux,input-type <EV_KEY> (this is the default for
gpio-keys);
- Allow the interrupt line for this button to be disabled;
- Use a full, descriptive node name;
- Set proper bias on the GPIO via pinctrl;
- Sort properties;
- Replace deprecated gpio-key,wakeup property with wakeup-source.
Fixes: 82e1783890 ("arm64: dts: qcom: sm6125: Add support for Sony Xperia 10II")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221222192443.119103-1-marijn.suijten@somainline.org
Sony's seine board features an SD Card slot on SDHCI 2, that is to be
powered by l5 and l22. The card detect pin is already biased via
updates on the generic sdc2_*_state pinctrl nodes.
As usual regulator voltages are decreased to the maximum voted by the
downstream driver for safety. SDHCI 2 is the only hardware block
feeding off of these.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221222203636.250190-5-marijn.suijten@somainline.org
While SDHCI 1 appears to work out of the box, we cannot rely on the
bootloader-enabled regulators nor expect them to remain enabled (e.g.
when finally dropping pd_ignore_unused). Provide it the necessary l24
and l11 regulators now that PM6125 regulators have been made available
on this board.
As usual regulator voltages are decreased to the maximum voted by the
downstream driver for safety. No other hardware feeds off of these
regulators anyway (except UFS, which isn't used on the seine board in
favour of a DV6DMB eMMC card connected to SDHCI 1).
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221222203636.250190-4-marijn.suijten@somainline.org
Document the use of l7, l10 and l15 in the High Speed Qualcomm USB2 PHY,
in order to keep the regulators voted on when USB is active.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221222203636.250190-3-marijn.suijten@somainline.org
Configure PM6125 regulators based on availability and voltages defined
downstream, to allow powering up (and/or keeping powered) other hardware
blocks going forward.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221222203636.250190-2-marijn.suijten@somainline.org
The gpio node in PMIC dts'es define access to multiple GPIOs. Most Qcom
PMICs were already using the plural _gpios label to point to this node,
but a few PMICs were left behind including the recently-pulled
pm(i)8950.
Rename it from *_gpio to *_gpios for pm6125, pm6150(l), pm8005,
pm(i)8950, and pm(i)8998.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221209220450.1793421-1-marijn.suijten@somainline.org
In addition to PMIC-specific (pm6125) thermistors downstream extends
this set with the rf-pa0/rf-pa1, quiet, camera-flash and UFS/eMMC
thermistors in sm6125 (trinket) board and seine-specific DT files. All
thermistors report sensible temperature readings in userspace.
The sensors are also added to their respective Thermal Monitor node,
with thermal zones to match where applicable: emmc-ufs and camera-flash
are not available on the TM5 block, hence cannot be configured with a
tripping point and will not have a thermal zone.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220926190148.283805-6-marijn.suijten@somainline.org
The Sony Xperia Seine board uses the PM6125; include it and configure
the PON buttons that provide the power and volume-up key.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220926190148.283805-5-marijn.suijten@somainline.org
Add default GPIO function to SD card detect pins on SM6125 Sony Xperia,
as required by bindings:
qcom/sm6125-sony-xperia-seine-pdx201.dtb: pinctrl@500000: sdc2-off-state: 'oneOf' conditional failed, one must be fixed:
'pins' is a required property
'function' is a required property
'clk-pins', 'cmd-pins', 'data-pins', 'sd-cd-pins' do not match any of the regexes: 'pinctrl-[0-9]+'
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220930192954.242546-10-krzysztof.kozlowski@linaro.org
DT schema expects TLMM pin configuration nodes to be named with '-state'
suffix and their optional children with '-pins' suffix.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220912061746.6311-35-krzysztof.kozlowski@linaro.org
According to qcom,sm6125-pinctrl.yaml all nodes inside the tlmm must be
suffixed by -state:
qcom/sm6125-sony-xperia-seine-pdx201.dtb: pinctrl@500000: 'sdc2-off', 'sdc2-on' do not match any of the regexes: '-state$', 'pinctrl-[0-9]+'
The label names have been updated to match, going from sdc2_state_X to
sdc2_X_state.
Fixes: cff4bbaf2a ("arm64: dts: qcom: Add support for SM6125")
Fixes: 82e1783890 ("arm64: dts: qcom: sm6125: Add support for Sony Xperia 10II")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220508100336.127176-2-marijn.suijten@somainline.org
Both the sdc2-on and sdc2-off pinctrl nodes are used by the
sdhci@4784000 node in sm6125.dtsi. Surprisingly sdc2-off is defined in
sm6125, yet its sdc2-on counterpart is only defined in board-specific DT
for the Sony Seine PDX201 board/device resulting in an "undefined label
&sdc2_state_on" error if sm6125.dtsi were included elsewhere.
This sm6125 base dtsi should not rely on externally defined labels; the
properties referencing it should then also be written externally.
Since the sdc2-on pin configuration is board-independent just like
sdc2-off, move it from seine-pdx201.dts into sm6125.dtsi.
The SDCard-detect pin (gpio98) is however board-specific, and remains as
an overwrite in seine-pdx201.dts for both the on and off state.
As a drive-by cleanup, reorder bias- and drive-strength properties.
Fixes: cff4bbaf2a ("arm64: dts: qcom: Add support for SM6125")
Fixes: 82e1783890 ("arm64: dts: qcom: sm6125: Add support for Sony Xperia 10II")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220508100336.127176-1-marijn.suijten@somainline.org
This property doesn't seem to exist in the documentation nor
in source code, but for some reason it is defined in a bunch
of device trees.
Signed-off-by: Dang Huynh <danct12@riseup.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211123162436.1507341-1-danct12@riseup.net
A new 'chassis-type' root node property has recently been approved for
the device-tree specification, in order to provide a simple way for
userspace to detect the device form factor and adjust their behavior
accordingly.
This patch fills in this property for end-user devices (such as laptops,
smartphones and tablets) based on Qualcomm ARM64 processors.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net> # msm8916
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211016102025.23346-4-arnaud.ferraris@collabora.com
This commits add support for Sony Xperia 10II based on the SM6125 SoC.
Currently working features:
- dmesg output to bootloader preconfigured display
- USB
- eMMC
- Volume down button
Signed-off-by: Martin Botka <martin.botka@somainline.org>
Link: https://lore.kernel.org/r/20210621195308.654587-2-martin.botka@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
