Device node names should be generic and bindings expect certain pattern
for RPMh regulator nodes.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230217155838.848403-3-krzysztof.kozlowski@linaro.org
DT schema expects PMIC GPIO pin configuration nodes to be named with
'-state' suffix:
qcom/sc7280-herobrine-crd.dtb: pmic@2: gpio@8800: 'edp-bl-reg-en' does not match any of the regexes: '-state$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220828084341.112146-11-krzysztof.kozlowski@linaro.org
Zoglin is a Hoglin Chromebook with SPI Flash reduced from 64MB to 8MB.
Zoglin is identical to Hoglin except for the SPI Flash.
The actual SPI Flash is dynamically probed at and not specified in DTS.
Signed-off-by: Bob Moragues <moragues@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220728143215.v3.2.I7d57fb9c4806a8b3fe3501c766b64f4987c271ef@changeid
Move wcd specific pin conf to common file to support various
herbronie variant boards and to avoid duplicate nodes in dts files.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1657197381-1271-1-git-send-email-quic_srivasam@quicinc.com
This adds the touchscreen to the sc7280-herobrine-villager device
tree. Note that the touchscreen on villager actually uses the reset
line and thus we use the more specific "elan,ekth6915" compatible
which allows us to specify the reset.
The fact that villager's touchscreen uses the reset line can be
contrasted against the touchscreen for CRD/herobrine-r1. On those
boards, even though the touchscreen goes to the display, it's not
hooked up to anything there.
In order to keep the line parked on herobrine/CRD, we'll move the
pullup from the qcard.dtsi file to the specific boards. This allows us
to disable the pullup in the villager device tree since the pin is an
output.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220524134840.1.I80072b8815ac08c12af8f379a33cc2d83693dc51@changeid
Add eDP support to herobrine boards, splitting up amongst the
different files as makes sense. Rationale for the current split of
things:
* The eDP connector itself is on qcard. However, not all devices with
a qcard will use an eDP panel. Some might use MIPI and, presumably,
someone could build a device with qcard that had no display at all.
* The qcard provides a PWM for backlight that goes to the eDP
connector. This PWM is also provided to the board and it's expected
that it would be used as the backlight PWM even for herobrine
devices with MIPI displays.
* It's currently assumed that all herobrine boards will have some sort
of display, either MIPI or eDP (but not both).
* We will assume herobrine-rev1 has eDP. The schematics allow for a
MIPI panel to be hooked up but, aside from some testing, nobody is
doing this and most boards don't have all the parts stuffed for
it. The two panels would also share a PWM for backlight, which is
weird.
* herobrine-villager and herobrine-hoglin (crd) also have eDP.
* herobrine-hoglin (crd) has slightly different regulator setup for
the backlight. It's expected that this is unique to this board. See
comments in the dts file.
* There are some regulators that are defined in the qcard schematic
but provided by the board like "vreg_edp_bl" and
"vreg_edp_3p3". While we could put references to these regulators
straight in the qcard.dtsi file, this would force someone using
qcard that didn't provide those regulators to provide a dummy or do
an ugly /delete-node/. Instead, we'll add references in
herobrine.dtsi.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220426124053.v2.1.Iedd71976a78d53c301ce0134832de95a989c9195@changeid
