Update the lpassaudio node to support the new compatible as the
lpassaudio needs to support the reset functionality on the
QCS6490 RB3Gen2 board and the rest of the Audio functionality would be
provided from the LPASS firmware.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20250221-lpass_qcm6490_resets-v5-4-6be0c0949a83@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The property qcom,ath11k-calibration-variant was deprecated in favor of
recently introduced generic qcom,calibration-variant, common to all
Qualcomm Atheros WiFi bindings.
Change will affect out of tree users, like other projects, of this DTS.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250225-dts-qcom-wifi-calibration-v1-10-347e9c72dcfc@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the PMU node for WCN6750 present on the qcs6490-rb3gen2
board and assign its power outputs to the Bluetooth module.
In WCN6750 module sw_ctrl and wifi-enable pins are handled
in the wifi controller firmware. Therefore, it is not required
to have those pins' entries in the PMU node.
Signed-off-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250221171014.120946-2-quic_janathot@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add support for vadc and adc-tm channels which are used for
monitoring thermistors present on the platform.
- Add the necessary includes for qcom,spmi-adc7-pm7325 and
qcom,spmi-adc7-pmk8350.
- Add thermal zones for quiet-thermal, sdm-skin-thermal, and
xo-thermal, and define their polling delays and thermal sensors.
- Configure the pm7325_temp_alarm node to use the pmk8350_vadc
channel for thermal monitoring.
- Configure the pmk8350_adc_tm node to enable its thermal sensors
and define their registers and settings.
- Configure the pmk8350_vadc node to define its channels and settings
Signed-off-by: Rakesh Kota <quic_kotarake@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250212113342.873086-1-quic_kotarake@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
RB3 Gen2 has a trio of LEDs connected to the PM8350C's Light Pulse
Generator. Describe them.
Use the "red channel" as a panic indicator by default.
Signed-off-by: Konrad Dybcio <quic_kdybcio@quicinc.com>
[bjorn: Corrected colors]
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241004-rb3gen2-leds-v1-2-437cdbb4f6c0@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable PCIe1 controller and its corresponding PHY nodes on
qcs6490-rb3g2 platform.
SMMU v2 has limited SID's to assign dynamic SID's with the existing
logic. For now, use static iommu-map table assigning unique SID's for
each port as dynamic approach needs boarder community discussions.
PCIe switch connected to this board has 3 downstream ports and
to the one of the downstream an embedded ethernet is connected.
Assign unique SID for each downstream port and to embedded ethernet,
and also reserve a SID for the endpoints which are going to be
connected to the other two downstream ports.
As this PCIe switch is present in this platform only update iommu-map
in this platform only as other board variants might have different
PCIe topology and might need different mapping.
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Link: https://lore.kernel.org/r/20241024-enable_pcie-v2-1-e5a6f5da74e4@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
RB3Gen2 has three tiny buttons located under the blue USB-A ports.
They're all connected through the various PMICs and are used for
volume and power.
Describe them.
Signed-off-by: Konrad Dybcio <quic_kdybcio@quicinc.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241004-rb3gen2-pwr-vol-keys-v1-1-4b1859c7cc4f@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Per the binding, omitting the clock frequency from a Geni I2C controller
node defaults the bus to 100Khz. But at least in Linux, a friendly info
print highlights the lack of explicitly defined frequency in the
DeviceTree.
Specify the frequency, to give it an explicit value, and to silence the
log print in Linux.
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241004-i2c1-frequency-v1-1-77a359015d54@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable the venus node on Qualcomm Rb3gen2 so that the
video decoder will start working.
Signed-off-by: Vedang Nagar <quic_vnagar@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240917-venus_rb3_gen2-v1-1-8fea70733592@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On SC7280 and derivative platforms GPU by default requires a signed
binary, a660_zap.mbn. Disable GPU by default and enable it only when
the binary is actually available (QCM6490-IDP, RB3gen2). ChromeOS
devices do not use TrustZone, so GPU can be enabled by default in
sc7280-chrome-common.dtsi. FairPhone5 and SHIFTphone8 DTS already
enable GPU (even though it wasn't required beforehand).
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
Link: https://lore.kernel.org/r/20240907-rb3g2-fixes-v1-2-eb9da98e9f80@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Newer boards should always use squashed MBN firmware instead of split
MDT+bNN. Use qcom/qcs6490/modem.mbn as the firmware for the modem on
RB3gen2.
Fixes: ac6d35b9b7 ("arm64: dts: qcom: qcs6490-rb3gen2: Enable various remoteprocs")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
Link: https://lore.kernel.org/r/20240907-rb3g2-fixes-v1-1-eb9da98e9f80@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Rb3Gen2 has a lt9611uxc DSI-to-HDMI bridge on i2c0, with
reset gpio from pm7250b gpio2 and irq gpio from tlmm gpio24.
Bridge supplies are Vdd connected to input supply directly
and vcc to L11c. Enable HDMI output, bridge and corresponding
DSI output.
Signed-off-by: Venkata Prahlad Valluru <quic_vvalluru@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240528141954.7567-1-quic_vvalluru@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
For IDP variant, GPIO 20/21 is used by camera use case and camera
driver is not able acquire these GPIOs as it is acquired by UART5
driver as RTS/CTS pin.
UART5 is designed for debug UART for all the board variants of the
sc7280 chipset and RTS/CTS configuration is not required for debug
uart usecase.
Remove CTS/RTS configuration for UART5 instance and change compatible
string to debug UART.
Remove overwriting compatible property from individual target specific
file as it is not required.
Fixes: 38cd93f413 ("arm64: dts: qcom: sc7280: Update QUPv3 UART5 DT node")
Signed-off-by: Viken Dadhaniya <quic_vdadhani@quicinc.com>
Link: https://lore.kernel.org/r/20240424075853.11445-1-quic_vdadhani@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable the ADSP, CDSP and WPSS that are found on qcs6490-rb3gen2.
Signed-off-by: Komal Bajaj <quic_kbajaj@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240417120928.32344-3-quic_kbajaj@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The rb3gen2 has UFS memory, adjust the necessary supply voltage and add
the controller and phy nodes to enable this.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240327-rb3gen2-ufs-v2-1-3de6b5dd78dd@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
With the ADSP remoteproc loaded pmic_glink can be introduced and
together with the redriver wired up to provide role and orientation
switching signals as well as USB Type-C display on the RB3gen2.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-By: Krishna Kurapati PSSNV <quic_kriskura@quicinc.com>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240326-rb3gen2-dp-connector-v2-5-a9f1bc32ecaf@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The RB3gen2 has a USB redriver on APPS_I2C, enable the bus and introduce
the redriver. The plumbing with other components is kept separate for
clarity.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240326-rb3gen2-dp-connector-v2-4-a9f1bc32ecaf@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The RB3Gen2 board comes with a mini DP connector, describe this, enable
MDSS, DP controller and the PHY that drives this.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240326-rb3gen2-dp-connector-v2-2-a9f1bc32ecaf@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Without explicitly specifying names for the regulators they are named
based on the DeviceTree node name. This results in multiple regulators
with the same name, making debug prints and regulator_summary impossible
to reason about.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240227-rb3gen2-regulator-names-v1-1-63ceb845dcc8@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Underscores should not be used in node names (dtc with W=2 warns about
them), so replace them with hyphens.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20240213145124.342514-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The SC7280 GCC binding describes clocks which, due to the difference in
security model, are not accessible on the RB3gen2 - in the same way seen
on QCM6490.
Mark these clocks as protected, to allow the board to boot. In contrast
to the present QCM6490 boards GCC_EDP_CLKREF_EN is left out, as this
does not need to be "protected" and is used on the RB3Gen2 board.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20240209-qcm6490-gcc-protected-clocks-v2-1-11cd5fc13bd0@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Min and max voltages for vph_pwr should be same, otherwise rpmh
will not probe, so correcting the min and max voltages for vph_pwr.
Fixes: 04cf333afc ("arm64: dts: qcom: Add base qcs6490-rb3gen2 board dts")
Signed-off-by: Komal Bajaj <quic_kbajaj@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231220110015.25378-3-quic_kbajaj@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
It appears that all SC7280-based devices so far have mpss_mem and
wpss_mem on the same reg with the same size.
Also these memory regions are referenced already in sc7280.dtsi so
that's where they should also be defined.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20231208-sc7280-remoteprocs-v3-4-6aa394d33edf@fairphone.com
[bjorn: delete-node &wpss_mem in qcs6490 rb3gen2, and qcm6490 idp]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the node for the ADSP found on the SC7280 SoC, using standard
Qualcomm firmware.
Remove the reserved-memory node from sc7280-chrome-common since CDSP is
currently not used there.
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20231208-sc7280-remoteprocs-v3-9-6aa394d33edf@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add DTS for Qualcomm qcs6490-rb3gen2 board which uses
QCS6490 SoC. This adds debug uart and usb support along
with regulators found on this board.
Co-developed-by: Naina Mehta <quic_nainmeht@quicinc.com>
Signed-off-by: Naina Mehta <quic_nainmeht@quicinc.com>
Signed-off-by: Komal Bajaj <quic_kbajaj@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Link: https://lore.kernel.org/r/20231129065816.26409-4-quic_kbajaj@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
