Unlike typical GIC interrupts, first cell for SPMI interrupts is the
USID rather than GIC_SPI/GIC_PPI/GIC_LPI qualifier. Fix the resin
interrupt to use USID value 0x0 rather than GIC_SPI define.
Fixes: f86ae6f23a ("arm64: dts: qcom: sagit: add initial device tree for sagit")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230409182145.122895-1-dmitry.baryshkov@linaro.org
Add a PM8998-specific compatible to the coincell charger and keep the
PM8941 one as fallback.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230214090849.2186370-3-konrad.dybcio@linaro.org
The gpio node in PMIC dts'es define access to multiple GPIOs. Most Qcom
PMICs were already using the plural _gpios label to point to this node,
but a few PMICs were left behind including the recently-pulled
pm(i)8950.
Rename it from *_gpio to *_gpios for pm6125, pm6150(l), pm8005,
pm(i)8950, and pm(i)8998.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221209220450.1793421-1-marijn.suijten@somainline.org
New device support - Xiaomi Mi6 phone
What works:
- storage
- usb
- power regulators
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Konrad Dybcio <konra.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221112203300.536010-3-dsankouski@gmail.com
The spmi-pmic bindings say that pm8941-coincell should be called
'charger'.
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221031175119.939860-3-luca@z3ntu.xyz
Add a node for the ADC Thermal Monitor found in the PM8998 PMIC. This is
used to connect thermal zones with ADC channels.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211005032531.2251928-4-bjorn.andersson@linaro.org
The thermal devicetree binding requires the "-thermal" suffix for all
thermal zones. Hence, add the missing suffix for PMIC based thermal
zones.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210118051005.55958-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We don't use the power key from the PMIC on Cheza. Disable this node so
that we don't probe the driver for this device.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200121171806.9933-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Unit name is supposed to be a number, using a macro with hex value is
not recommended, so add the value in unit name.
arch/arm64/boot/dts/qcom/pm8998.dtsi:81.18-84.6: Warning (unit_address_format): /soc/spmi@c440000/pmic@0/adc@3100/adc-chan@0x06: unit name should not have leading "0x"
arch/arm64/boot/dts/qcom/pm8998.dtsi:81.18-84.6: Warning (unit_address_format): /soc/spmi@c440000/pmic@0/adc@3100/adc-chan@0x06: unit name should not have leading 0s
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This changes pm8998 to use the new qcom,pm8998-pon compatible
string for the pon in order to support the gen2 pon
functionality properly.
Cc: Andy Gross <agross@kernel.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
The temperature information from the temp-alarm block itself is very
coarse ("temperature is above/below trip points"). Provide the driver
with the die temperature channel of the ADC on the PMIC for more precise
readings.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <agross@kernel.org>
This adds the gpio-ranges property so that the GPIO pins are initialized
by the GPIO framework and not pinctrl. This fixes a circular dependency
between these two frameworks so GPIO hogging can be used on this board.
This was not tested on this particular hardware, however this same
change was tested on qcom-pm8941 using a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a channel node for the die temperature to the ADC.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The thermal zone uses spmi-temp-alarm as sensor, the trip points
correspond to the PMIC thermal stages 1 and 2. The critical trip
point at 125°C disables the partial PMIC shutdown at stage 2.
Without an IIO input the sensor only reports a limited number of
temperatures:
- 37°C for temperatures below 105°C
- 107°C for temperatures >= 105°C and < 125°C
- 127°C for temperatures >= 125°C
(the numbers correspond to a stage 1 threshold of 105°C)
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the spmi-temp-alarm node to pm8998 based on the examples in the
bindings.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add pon, coincell and rtc to the first pm8998 sid.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the adc node to pm8998 based on the examples in the
bindings. It also fixes the order of the included headers.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add basic support for the pm8005 and pm8998 PMICs. For now just support
the GPIO controllers.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
