The phones listed below have Richtek RT5033 PMIC and charger.
Add them to the device trees.
- Samsung Galaxy A3/A5/A7 2015
- Samsung Galaxy E5/E7
- Samsung Galaxy Grand Max
Signed-off-by: Raymond Hackley <raymondhackley@protonmail.com>
Link: https://lore.kernel.org/r/20240424143158.24358-1-raymondhackley@protonmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Now that we no longer have fixed addresses for the firmware memory
regions, disable them by default and only enable them together with
the actual user in the board DT.
This frees up unnecessary reserved memory for boards that do not use
some of the remoteprocs and allows moving selected device-specific
properties (such as firmware size) to the board-specific DT part in
the next step.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230911-msm8916-rmem-v1-7-b7089ec3e3a1@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
MSM8916 is the only ARM64 Qualcomm SoC that is still using the old
&msmgpio name. Change this to &tlmm to avoid confusion.
Note that the node ordering does not change because the MSM8916 device
trees have pinctrl separated at the bottom (similar to sc7180).
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230525-msm8916-labels-v1-1-bec0f5fb46fb@gerhold.net
On MSM8916 the wireless connectivity functionality (WiFi/Bluetooth) is
split into the digital part inside the SoC and the analog RF part inside
a supplementary WCN36xx chip. For MSM8916, three different options
exist:
- WCN3620 (WLAN 802.11 b/g/n 2.4 GHz + Bluetooth)
- WCN3660B (WLAN 802.11 a/b/g/n 2.4/5 GHz + Bluetooth)
- WCN3680B (WLAN 802.11ac 2.4/5 GHz + Bluetooth)
Choosing one of these is up to the board vendor. This means that the
compatible belongs into the board-specific DT part so people porting
new boards pay attention to set the correct compatible.
Right now msm8916.dtsi sets "qcom,wcn3620" as default compatible,
which does not work at all for boards that have WCN3660B or WCN3680B.
Remove the default compatible from msm8196.dtsi and move it to the board
DT as follows:
- Boards with only &pronto { status = "okay"; } used the default
"qcom,wcn3620" so far. They now set this explicitly for &wcnss_iris.
- Boards with &pronto { ... iris { compatible = "qcom,wcn3660b"; }};
already had an override that just moves to &wcnss_iris now.
- For msm8916-samsung-a2015-common.dtsi the WCN compatible differs for
boards making use of it (a3u: wcn3620, a5u: wcn3660b, e2015: wcn3620)
so the definitions move to the board-specific DT part.
Since this requires touching all the board DTs, use this as a chance to
name the WCNSS-related labels consistently, so everything is grouped
properly when sorted alphabetically.
No functional change, just clean-up for more clarity & easier porting.
Aside from ordering the generated DTBs are identical.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230309091452.1011776-1-stephan.gerhold@kernkonzept.com
DT schema expects TLMM pin configuration nodes to be named with
'-state' suffix and their optional children with '-pins' suffix.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221024002356.28261-2-krzysztof.kozlowski@linaro.org
Both a2015 devices use motor drivers controlled with PWM signal.
A5 additionally has a fixed regulator that powers the driver and is
controlled by enable signal. A3 routes that enable signal to the
motor driver itself.
To simplify the description, add the motor to the common dtsi and
assume a regulator is used for both.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
[Rename the nodes to be reusable in msm8916-sansung-e2015]
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221020115255.2026-1-linmengbo0689@protonmail.com
reg_vdd_tsp: regulator-vdd-tsp is actually used as an analog regulator for
touchscreen on all of a2015 and e2015 devices.
Rename it into reg_vdd_tsp_a: regulator-vdd-tsp-a to reduce confusion.
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220724095438.14252-1-linmengbo0689@protonmail.com
A3, A5 and most of the Samsung phones with MSM8916 SoC use GPIO pin 13 for
touchscreen interrupts. Add touchscreen pinctrl to a2015 common dtsi.
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220610175332.104154-1-linmengbo0689@protonmail.com
A new 'chassis-type' root node property has recently been approved for
the device-tree specification, in order to provide a simple way for
userspace to detect the device form factor and adjust their behavior
accordingly.
This patch fills in this property for end-user devices (such as laptops,
smartphones and tablets) based on Qualcomm ARM64 processors.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net> # msm8916
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211016102025.23346-4-arnaud.ferraris@collabora.com
On the Samsung Galaxy A5 the touch key is supplied by a single fixed
regulator (enabled via GPIO 97) that supplies both MCU and LED.
Add it to the device tree.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Unlike most MSM8916 boards, samsung-a5u uses WCN3660B instead of
WCN3620 to support the 5 GHz band additionally.
WCN3660B has similar requirements as WCN3620, but it needs the XO
clock to run at 48 MHz instead of 19.2 MHz. So far it was possible
to describe that configuration using the qcom,wcn3680 compatible.
However, as of commit 8490987bdb ("wcn36xx: Hook and identify RF_IRIS_WCN3680"),
the wcn36xx driver will now use the qcom,wcn3680 compatible
to enable functionality specific to WCN3680. In particular,
WCN3680 supports 802.11ac, which is not available in WCN3660B.
Use the new qcom,wcn3660b compatible to describe the chip properly.
Fixes: 0d70519991 ("arm64: dts: msm8916-samsung-a5u: Override iris compatible")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210106102134.59801-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A3U/A5U both use a Bosch BMC150 accelerometer/magnetometer combo.
The chip provides two separate I2C devices for the accelerometer
and magnetometer that are already supported by the bmc150-accel
and bmc150-magn driver.
The only difference between A3U/A5U is the way the sensor is
mounted on the mainboard - set the mount-matrix in the
device-specific device tree part to handle that difference.
Co-developed-by: Michael Srba <michael.srba@seznam.cz>
Signed-off-by: Michael Srba <michael.srba@seznam.cz>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200622151751.408995-5-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
So far we have been separating pinctrl entries into pinmux/pinconf.
It turns out it is also possible to combine them: The advantage is
that the device tree is overall more concise because the "pins"
to configure just need to be specified once, not separately for
pinmux/pinconf.
Using the simpler form only for new entries would be rather confusing.
This commit makes all MSM8916 device trees use the simplfied form.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200622151751.408995-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A5U uses a Melfas MMS345L touchscreen that is connected to
blsp_i2c5. Add it to the device tree.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200426140642.204395-5-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
msm8916.dtsi sets the iris compatible to "qcom,wcn3620".
While WCN3620 seems to be used on most MSM8916 devices,
MSM8916 can also be paired with another chip (e.g. for WiFi dual-band).
A5U uses WCN3660B instead, so the compatible needs to be overridden
to apply the correct configuration.
However, simply using "qcom,wcn3660" would be incorrect,
since WCN3660B requires a slightly different regulator configuration
compared to WCN3660.
Instead, it requires the same configuration as "qcom,wcn3680".
Replace the compatible with "qcom,wcn3680" for A5U to make WCNSS
work correctly.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Samsung Galaxy A3 (SM-A300FU) and Samsung Galaxy A5 (SM-A500FU)
are smartphones using the MSM8916 SoC released in 2015.
Add a device tree for A3U and A5U with initial support for:
- SDHCI (internal and external storage)
- USB Device Mode
- UART (on USB connector via the SM5502 MUIC)
- Regulators
The two devices (and all other variants of A3/A5 released in 2015)
are very similar, with some differences in display, touchscreen
and sensors. The common parts are shared in
msm8916-samsung-a2015-common.dtsi to reduce duplication.
The device tree is loosely based on apq8016-sbc.dtsi and the
downstream kernel provided by Samsung, mixed with a lot of own
research.
Co-developed-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
