Remove the generic UART pinctrl templates from msm8916.dtsi and copy the
definition for the custom UART use cases into the board DT files. This
makes it clear that the set of pins/pull etc are specific to the board and
UART use case.
No functional change.
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20250422-msm8916-console-pinctrl-v2-5-f345b7a53c91@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Convert the majority of MSM8916/39-based boards, which use UART2 with 2
pins (TX, RX) for the debug UART console. This adds the needed bias-pull-up
and bootph-all properties to avoid garbage input when UART is disconnected.
apq8016-schneider-hmibsc.dts does not use UART2 as a debug console, so it's
left as-is in this commit.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20250422-msm8916-console-pinctrl-v2-3-f345b7a53c91@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
In preparation of adding a new console UART specific pinctrl template, move
the pinctrl reference to the board DT part. This forces people porting new
boards to consider what exactly they need for their board.
No functional change for the boards upstream.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20250422-msm8916-console-pinctrl-v2-1-f345b7a53c91@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the missing regulator supplies to the ADV7533 HDMI bridge to fix
the following dtbs_check warnings. They are all also supplied by
pm8916_l6 so there is no functional difference.
apq8016-sbc.dtb: bridge@39: 'dvdd-supply' is a required property
apq8016-sbc.dtb: bridge@39: 'pvdd-supply' is a required property
apq8016-sbc.dtb: bridge@39: 'a2vdd-supply' is a required property
from schema display/bridge/adi,adv7533.yaml
Fixes: 28546b0955 ("arm64: dts: apq8016-sbc: Add HDMI display support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230922-db410c-adv7533-regulators-v1-1-68aba71e529b@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The modem firmware size is typically highly device-specific.
The current size of the mpss_mem region in msm8916.dtsi (0x2b00000)
only works for some APQ8016 devices without full-featured modem,
such as the DragonBoard 410c.
The full modem firmware is typically about twice as large (~45 MiB
-> ~90 MiB) but also varies by a few MiB from device to device. Since
these devices are quite memory-constrained nowadays it's important to
minimize the unnecessary memory reservations.
Make it clear that each board needs to specify the necessary mpss_mem
size by replacing the DB410c-specific size in msm8916.dtsi with a
simple comment. &mpss_mem is disabled by default so it's fine to leave
some properties up to the boards if they want to enable it.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230911-msm8916-rmem-v1-8-b7089ec3e3a1@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Now that we no longer have fixed addresses for the firmware memory
regions, disable them by default and only enable them together with
the actual user in the board DT.
This frees up unnecessary reserved memory for boards that do not use
some of the remoteprocs and allows moving selected device-specific
properties (such as firmware size) to the board-specific DT part in
the next step.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230911-msm8916-rmem-v1-7-b7089ec3e3a1@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
MSM8916/39 do not need signed GPU firmware so it is generally okay to
have it enabled by default. However, currently the GPU does not work
without also enabling MDSS and it's questionable if someone would
really need it without a display in practice.
For consistency let's follow newer SoCs and disable the GPU by default.
Enable it for all existing devices that already have &mdss enabled.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230911-msm8916-rmem-v1-2-b7089ec3e3a1@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Venus needs firmware that is usually signed with a device-specific key.
There are also devices that might not need it (especially during
bring-up), so let's follow more recent SoCs and disable it by default.
Enable it explicitly for all current devices except msm8916-mtp. That
one has just UART enabled currently so it cannot really benefit from
Venus.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230911-msm8916-rmem-v1-1-b7089ec3e3a1@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Drop the redundant reg-names and mclk from the PM8916 analog codec that
were removed from the DT schema. Having the mclk on the analog codec is
incorrect because only the digital codec consumes it directly.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230718-pm8916-mclk-v1-6-4b4a58b4240a@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
At the moment we define a single ov5640 sensor in the apq8016-sbc and
disable that sensor.
The sensor mezzanine for this is a D3 Engineering Dual ov5640 mezzanine
card. Move the definition from the apq8016-sbc where it shouldn't be to a
standalone dts.
Enables the sensor by default, as we are adding a standalone mezzanine
structure.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230811234738.2859417-7-bryan.odonoghue@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
There are two control lines controlled by GPIO going into ov5640
- Reset
- Powerdown
The driver and yaml expect "reset-gpios" and "powerdown-gpios" there has
never been an "enable-gpios".
Fixes: 39e0ce6cd1 ("arm64: dts: qcom: apq8016-sbc: Add CCI/Sensor nodes")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230811234738.2859417-6-bryan.odonoghue@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The driver for the ov5640 doesn't do a set-rate, instead it expects the
clock to already be set at an appropriate rate.
Similarly the yaml for ov5640 doesn't understand clock-frequency. Convert
from clock-rate to assigned-clock and assigned-clock-rate to remediate.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230811234738.2859417-5-bryan.odonoghue@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The yaml constraint for data-lanes is [1, 2] not [0, 2]. The driver itself
doesn't do anything with the data-lanes declaration save count the number
of specified data-lanes and calculate the link rate so, this change doesn't
have any functional side-effects.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230811234738.2859417-4-bryan.odonoghue@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The ov5640 driver expects DOVDD, AVDD and DVDD as regulator supply names.
The ov5640 has depended on these names since the driver was committed
upstream in 2017. Similarly apq8016-sbc.dtsi has had completely different
regulator names since its own initial commit in 2020.
Perhaps the regulators were left on in previous 410c bootloaders. In any
case today on 6.5 we won't switch on the ov5640 without correctly naming
the regulators.
Fixes: 39e0ce6cd1 ("arm64: dts: qcom: apq8016-sbc: Add CCI/Sensor nodes")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230811234738.2859417-3-bryan.odonoghue@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
I2C and SPI controller bindings do not allow label property:
apq8016-sbc.dtb: spi@78b7000: Unevaluated properties are not allowed ('label' was unexpected)
apq8016-sbc.dtb: i2c@78b6000: Unevaluated properties are not allowed ('label' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230617171541.286957-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The audio pinctrl in MSM8916/MSM8939 is very similar but still has
subtle differences, e.g. &cdc_pdm_lines_act on MSM8916 vs
&cdc_pdm_lines_default on MSM8939.
Make this consistent and use the chance to cleanup all of the audio
pinctrl: Drop unneeded outer nodes and replace the names taken over
from the vendor kernel with more clear ones that are similar to the
actual pinctrl function.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230529-msm8916-pinctrl-v1-4-11f540b51c93@gerhold.net
GPIO116 is not connected (NC) on DB410c so there is no need to route
MCLK there. The MSM8916 digital codec receives the MCLK internally
without leaving the SoC through a GPIO.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230529-msm8916-pinctrl-v1-3-11f540b51c93@gerhold.net
MSM8939 has the SDC pinctrl consolidated in two &sdcN_default and
&sdcN_sleep states, while MSM8916 has all pins separated. Make this
consistent by consolidating them for MSM8916 well.
Use this as a chance to define default pinctrl in the SoC.dtsi and only
let boards that add additional definitions (such as cd-gpios) override it.
For MSM8939 just make the label consistent with the other pinctrl
definitions (they do not have a _state suffix).
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230529-msm8916-pinctrl-v1-2-11f540b51c93@gerhold.net
The current SD card detect pinctrl setup configures bias-pull-up for
the "default" (active) case and bias-disable for the "sleep" case.
Before commit b5c833b703 ("mmc: sdhci-msm: Set IO pins in low power
state during suspend") the pull up was permanently active. Since then
it is only active when a valid SD card is inserted.
This does not really make sense: For an active-low CD, the pull up is
needed to pull the GPIO high when the card is not inserted. When the
card gets inserted CD is shorted to ground (low). This means right now
the pull-up is removed exactly when it is needed to detect the next
card insertion. Generally, applying different bias for CD does not
really make sense. It should always stay the same so card removals and
insertions can be detected properly.
The reason why card detection still works fine in practice is that most
boards seem to have external pull up on the CD pin. However, this means
that there is no need to configure an internal pull-up at all and we
can keep bias-disable permanently.
There are also some boards with different CD polarity (acer-a1-724) and
with different GPIO number (huawei-g7). All in all this makes it
obvious that the CD pin is board-specific and the pinctrl for it should
be defined in the board DT.
Move it to the boards that need it and use bias-disable permanently for
the boards that seem to have external pull-up. The vendor device tree
for msm8939-sony-xperia-kanuti-tulip suggests that it needs the
internal pull-up permanently [1] so it gets bias-pull-up to be sure.
[1]: 57b5050e34/arch/arm/boot/dts/qcom/msm8939-kanuti_tulip.dtsi (L634-L636)
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230529-msm8916-pinctrl-v1-1-11f540b51c93@gerhold.net
MSM8939 has the aliases defined separately for each board (because
there could be (theoretically) a board where the slots are numbered
differently. To make MSM8916 and MSM8939 more consistent do the same
for all MSM8916 boards and move aliases there.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230525-msm8916-labels-v1-6-bec0f5fb46fb@gerhold.net
All definitions in pm8916.dtsi use the &pm8916_ label prefix, only the
codec uses the &wcd_codec label. &wcd_codec is confusing because the
codec on MSM8916 is split into a "wcd-digital" and "wcd-analog" part
and both could be described with &wcd_codec.
Let's just name it &pm8916_codec so it's consistent with all other PMIC
device nodes.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230525-msm8916-labels-v1-5-bec0f5fb46fb@gerhold.net
Right now MDSS related definitions cannot be properly grouped together
in board DTs because the labels do not use consistent prefixes. The DSI
PHY label is particularly weird because the DSI number is at the end
(&dsi_phy0) while DSI itself is called &dsi0.
Follow the example of more recent SoCs and give all the MDSS related
nodes a consistent label that allows proper grouping.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230525-msm8916-labels-v1-4-bec0f5fb46fb@gerhold.net
Make the labels for the BLSP I2C/SPI pinctrl consistent with the one
used for UART by adding the missing blsp_ prefix. This allows having
them properly grouped together.
The nodes are only reordered in msm8939.dtsi for now since the pinctrl
definitions in msm8916-pins.dtsi are currently still unordered anyway.
(I will try fixing this in a future patch.)
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230525-msm8916-labels-v1-3-bec0f5fb46fb@gerhold.net
For some reason the BLSP UART controllers have a label with a number
behind blsp (&blsp1_uartN) while I2C/SPI are named without (&blsp_i2cN).
This is confusing, especially for proper node ordering in board DTs.
Right now all board DTs are ordered as if the number behind blsp does
not exist (&blsp_i2cN comes before &blsp1_uartN). Strictly speaking
correct ordering would be the other way around ('1' comes before '_').
End this confusion by giving the UART controllers consistent labels.
There is just one BLSP on MSM8916/39 so the number is redundant.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230525-msm8916-labels-v1-2-bec0f5fb46fb@gerhold.net
MSM8916 is the only ARM64 Qualcomm SoC that is still using the old
&msmgpio name. Change this to &tlmm to avoid confusion.
Note that the node ordering does not change because the MSM8916 device
trees have pinctrl separated at the bottom (similar to sc7180).
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230525-msm8916-labels-v1-1-bec0f5fb46fb@gerhold.net
Some of the regulators must be always-on to ensure correct operation of
the system, e.g. PM8916 L2 for the LPDDR RAM, L5 for most digital I/O
and L7 for the CPU PLL (strictly speaking the CPU PLL might only need
an active-only vote but this is not supported for regulators in
mainline currently).
The RPM firmware seems to enforce that internally, these supplies stay
on even if we vote for them to power off (and there is no other
processor running). This means it's pointless to keep sending
enable/disable requests because they will just be ignored.
Also, drivers are much more likely to get a wrong impression of the
regulator status, because regulator_is_enabled() will return false when
there are no users, even though the regulator is always on.
Describe this properly by marking the regulators as always-on.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-8-54d4960a05fc@gerhold.net
Right now each MSM8916 device has a huge block of regulator constraints
with allowed voltages for each regulator. For lack of better
documentation these voltages are often copied as-is from the vendor
device tree, without much extra thought.
Unfortunately, the voltages in the vendor device trees are often
misleading or even wrong, e.g. because:
- There is a large voltage range allowed and the actual voltage is
only set somewhere hidden in some messy vendor driver. This is often
the case for pm8916_{l14,l15,l16} because they have a broad range of
1.8-3.3V by default.
- The voltage is actually wrong but thanks to the voltage constraints
in the RPM firmware it still ends up applying the correct voltage.
To have proper regulator constraints it is important to review them in
context of the usage. The current setup in the MSM8916 device trees
makes this quite hard because each device duplicates the standard
voltages for components of the SoC and mixes those with minor
device-specific additions and dummy voltages for completely unused
regulators.
The actual usage of the regulators for the SoC components is in
msm8916-pm8916.dtsi, so it can and should also define the related
voltage constraints. These are not board-specific but defined in the
APQ8016E/PM8916 Device Specification. The board DT can then focus on
describing the actual board-specific regulators, which makes it much
easier to review and spot potential mistakes there.
Note that this commit does not make any functional change. All used
regulators still have the same regulator constraints as before. Unused
regulators do not have regulator constraints anymore because most of
these were too broad or even entirely wrong. They should be added back
with proper voltage constraints when there is an actual usage.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-7-54d4960a05fc@gerhold.net
Not every device has something connected to the digital audio codec
in MSM8916 and/or the analog audio codec in PM8916. Disable those by
default so the hardware is only powered up when necessary.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-4-54d4960a05fc@gerhold.net
The 96Boards specification expects a 1.8V power rail on the low-speed
expansion connector that is able to provide at least 0.18W / 100 mA.
According to the DB410c hardware user manual this is done by connecting
both L15 and L16 in parallel with up to 55mA each (for 110 mA total) [1].
Unfortunately the current regulator setup in the DB410c device tree
does not implement the specification correctly and only provides 5 mA:
- Only L15 is marked always-on, so L16 is never enabled.
- Without specifying a load the regulator is put into LPM where
it can only provide 5 mA.
Fix this by:
- Adding proper voltage constraints for L16.
- Making L16 always-on.
- Adding regulator-system-load for both L15 and L16. 100 mA should be
available in total, so specify 50 mA for each. (The regulator
hardware can only be in normal (55 mA) or low-power mode (5 mA) so
this will actually result in the expected 110 mA total...)
[1]: https://www.96boards.org/documentation/consumer/dragonboard/dragonboard410c/hardware-docs/hardware-user-manual.md.html#power-supplies
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 828dd5d66f ("arm64: dts: apq8016-sbc: make 1.8v available on LS expansion")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-2-54d4960a05fc@gerhold.net
For some reason DB410c has completely bogus regulator constraints that
actually just correspond to the programmable voltages which are already
provided by the regulator driver. Some of them are not just outside the
recommended operating conditions of the APQ8016E SoC but even exceed
the absolute maximum ratings, potentially risking permanent device
damage.
In practice it's not quite as dangerous thanks to the RPM firmware:
It turns out that it has its own voltage constraints and silently
clamps all regulator requests. For example, requesting 3.3V for L5
(allowed by the current regulator constraints!) still results in 1.8V
being programmed in the actual regulator hardware.
Experimentation with various voltages shows that the internal RPM
voltage constraints roughly correspond to the safe "specified range"
in the PM8916 Device Specification (rather than the "programmable
range" used inside apq8016-sbc.dtsi right now).
Combine those together with some fixed voltages used in the old
msm-3.10 device tree from Qualcomm to give DB410c some actually valid
voltage constraints.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 4c7d53d16d ("arm64: dts: apq8016-sbc: add regulators support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-1-54d4960a05fc@gerhold.net
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407180045.126952-1-krzysztof.kozlowski@linaro.org
On MSM8916 the wireless connectivity functionality (WiFi/Bluetooth) is
split into the digital part inside the SoC and the analog RF part inside
a supplementary WCN36xx chip. For MSM8916, three different options
exist:
- WCN3620 (WLAN 802.11 b/g/n 2.4 GHz + Bluetooth)
- WCN3660B (WLAN 802.11 a/b/g/n 2.4/5 GHz + Bluetooth)
- WCN3680B (WLAN 802.11ac 2.4/5 GHz + Bluetooth)
Choosing one of these is up to the board vendor. This means that the
compatible belongs into the board-specific DT part so people porting
new boards pay attention to set the correct compatible.
Right now msm8916.dtsi sets "qcom,wcn3620" as default compatible,
which does not work at all for boards that have WCN3660B or WCN3680B.
Remove the default compatible from msm8196.dtsi and move it to the board
DT as follows:
- Boards with only &pronto { status = "okay"; } used the default
"qcom,wcn3620" so far. They now set this explicitly for &wcnss_iris.
- Boards with &pronto { ... iris { compatible = "qcom,wcn3660b"; }};
already had an override that just moves to &wcnss_iris now.
- For msm8916-samsung-a2015-common.dtsi the WCN compatible differs for
boards making use of it (a3u: wcn3620, a5u: wcn3660b, e2015: wcn3620)
so the definitions move to the board-specific DT part.
Since this requires touching all the board DTs, use this as a chance to
name the WCNSS-related labels consistently, so everything is grouped
properly when sorted alphabetically.
No functional change, just clean-up for more clarity & easier porting.
Aside from ordering the generated DTBs are identical.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230309091452.1011776-1-stephan.gerhold@kernkonzept.com
Adding the "dmas" to the I2C controllers prevents probing them if
blsp_dma is disabled (infinite probe deferral). Avoid this by enabling
blsp_dma by default - it's an integral part of the SoC that is almost
always used (even if just for UART).
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230107110958.5762-2-stephan@gerhold.net
Switch '//' comments to C-style /* */ and fix up the contents of some.
Make sure all multiline C-style commends begin with just '/*' with
the comment text starting on a new line.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221107145522.6706-2-konrad.dybcio@linaro.org
DT schema expects TLMM pin configuration nodes to be named with
'-state' suffix and their optional children with '-pins' suffix.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221024002356.28261-2-krzysztof.kozlowski@linaro.org
Fix whitespace coding style: use single space instead of tabs or
multiple spaces around '=' sign in property assignment. No functional
changes (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220526204248.832139-1-krzysztof.kozlowski@linaro.org
DT schema expects PMIC GPIO pin configuration nodes to be named with
'-state' suffix. Optional children should be either 'pinconf' or
followed with '-pins' suffix. This fixes dtbs_check warnings like:
sdm845-xiaomi-beryllium.dtb: gpios@c000: 'vol-up-active' does not match any of the regexes: '-state$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220507194913.261121-6-krzysztof.kozlowski@linaro.org
qcom,apq8016-sbc-sndcard is now covered by the qcom,sm8250.yaml schema
which has slightly different recommendations for the naming of
properties and nodes. The old naming is still functional but
deprecated. Update the &sound node in apq8016-sbc to fix the following
dtbs_check warnings:
apq8016-sbc.dt.yaml: sound@7702000: 'model' is a required property
From schema: sound/qcom,sm8250.yaml
apq8016-sbc.dt.yaml: sound@7702000: 'external-dai-link@0', ...
do not match any of the regexes: '.*-dai-link$', ...
From schema: sound/qcom,sm8250.yaml
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211214135124.2380-1-stephan@gerhold.net
The clock-lanes property is no longer used as it is not programmable by
the CSIPHY hardware block of Qcom ISPs and should be removed.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211206154003.39892-2-robert.foss@linaro.org
For some reason apq8016-sbc, apq8096-db820c, msm8916-mtp and msm8996-mtp
were added as separate .dts and .dtsi files where the first only contains
the model name and the latter contains most of the actual definitions.
Perhaps this was done with the expectation that there would be other
devices also making use of exactly the same. However, this has not
been the case until now and it also seems unlikely in the future.
Having the extra .dtsi only clutters the file list and provides
little benefit.
Move the contents of the .dtsi into the .dts file to make this consistent
with most other devices that simply define everything in the .dts.
There are no functional changes introduced by this patch:
The compiled ".dtb"s are completely identical.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211018133656.32649-1-stephan@gerhold.net
apq8016-sbc is one of the compaitibles for this board, but is not
documented, so drop it. This fixes these two warns:
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: /: compatible: ['qcom,apq8016-sbc', 'qcom,apq8016', 'qcom,sbc']
is not valid under any of the given schemas (Possible causes of the failure):
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: /: compatible: ['qcom,apq8016-sbc', 'qcom,apq8016', 'qcom,sbc'] is too long
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: /: compatible:0: 'qcom,apq8016-sbc'
is not one of ['qcom,apq8064-cm-qs600', 'qcom,apq8064-ifc6410']
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: /: compatible:0: 'qcom,apq8016-sbc'
is not one of ['qcom,apq8074-dragonboard']
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-2-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add initial device tree support for Qualcomm APQ8016 SBC Evaluation board.
This board is also referred to as the DragonBoard 410c.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
