Add audio support for the NVIDIA Jetson Orin NX (p3767, SKU0) module and
Jetson Orin Nano (p3767, SKU5) module Developer Kit with P3768 carrier
board.
APE and HDA sound cards are enabled.
Supported IO interfaces: I2S2 and I2S4.
Signed-off-by: sheetal <sheetal@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra234 boards use a mixture of aliases for the SD/MMC hardware blocks,
which can lead to confusion. A common method was to use mmc3 as the
alias for the eMMC because "SDMMC3" happens to be the name of the
corresponding controller in the reference manual. This isn't a great
choice because there is no hardware named SDMMC0, so the mmc0 alias
would never get used with that nomenclature and in fact mmc1 and mmc2
wouldn't either in many configurations, thereby creating weird
discontiguous enumeration.
Instead of trying to match the aliases to the hardware block names, use
mmc0 to denote the device's primary SD/MMC controller (typically eMMC)
and mmc1 for the secondary SD/MMC controller (typically removable SD).
In cases where eMMC is the only controller we can omit the mmc1 alias
and if a device has no eMMC, the removable SD card can be aliased to
mmc0 instead.
Co-developed-by: Russell Xiao <russellx@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate the ina219 and ina3221 power-sensors for the various Tegra234
boards. These sensors are located on the Tegra234 module boards and the
configuration of some sensors is common across the different Tegra234
modules. Therefore, add any common sensor configurations to appropriate
device tree source file so it can be re-used across modules.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The QSPI device used on Jetson Orin NX and Nano modules (p3767) is
the same as Jetson AGX Orin (p3701) and should have a maximum speed of
102 MHz.
Fixes: 13b0aca303 ("arm64: tegra: Support Jetson Orin NX")
Signed-off-by: Brad Griffis <bgriffis@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SD card detect pin is active-low on all Orin Nano and NX SKUs that
have an SD card slot.
Fixes: 13b0aca303 ("arm64: tegra: Support Jetson Orin NX")
Signed-off-by: Brad Griffis <bgriffis@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
It turns out that these devices can get quite hot to the touch with the
standard cooling configuration, so add another trip point at 35°C along
with a cooling map to help keep the system reasonably cool at very low
system load.
Reviewed-by: Yi-Wei Wang <yiweiw@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable the TJ thermal zone and hook up cooling maps for the PWM-
controlled fan and two trip points.
This also removes a duplicate definition of the PWM fan and changes its
cooling levels. This should have no effect, though, because the fan
wasn't previously connected to anything and by default would be turned
off at probe time.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds a device tree for the Jetson Orin NX module, which is Jetson
AGX Orin's little sibling with 6 or 8 ARM Cortex-A78AE cores, an Ampere
GPU (1024 GPU and 32 tensor cores) and a number of accelerators for
machine learning, image processing and more.
The Jetson Orin NX comes with either 8 or 16 GiB of 128-bit LPDDR5 and
supports NVME for mass storage.
Signed-off-by: Thierry Reding <treding@nvidia.com>
