There is no such device as "as3722@40", because its name is "pmic". Use
phandles for aliases to fix relying on full node path. This corrects
aliases for RTC devices and also fixes dtc W=1 warning:
tegra132-norrin.dts:12.3-36: Warning (alias_paths): /aliases:rtc0: aliases property is not a valid node (/i2c@7000d000/as3722@40)
Fixes: 0f279ebdf3 ("arm64: tegra: Add NVIDIA Tegra132 Norrin support")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The cros_ec driver currently assumes that cros-ec-spi compatible device
nodes are a wakeup-source even though the wakeup-source property is not
defined.
Some Chromebooks use a separate wake pin, while others overload the
interrupt for wake and IO. With the current assumption, spurious wakes
can occur on systems that use a separate wake pin. It is planned to
update the driver to no longer assume that the EC interrupt pin should
be enabled for wake.
Add the wakeup-source property to all cros-ec-spi compatible device
nodes to signify to the driver that they should still be a valid wakeup
source.
Signed-off-by: Mark Hasemeyer <markhas@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The debug UART doesn't support DMA and the DT bindings prohibit the use
of the dmas and dma-names properties for it, so remove them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Nodes in device tree should be sorted by unit-address, followed by nodes
without a unit-address, sorted alphabetically. Some exceptions are the
top-level aliases, chosen, firmware, memory and reserved-memory nodes,
which are expected to come first.
These rules apply recursively with some exceptions, such as pinmux nodes
or regulator nodes, which often follow more complicated ordering (often
by "importance").
While at it, change the name of some of the nodes to follow standard
naming conventions, which helps with the sorting order and reduces the
amount of warnings from the DT validation tools.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pinmux node names should have a pinmux- prefix and not use underscores.
Fix up some cases that didn't follow those rules.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra PMC device tree bindings don't support the "#wake-cells" and
"nvidia,reset-gpio" properties, so remove them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AS3722 pinmux device tree node doesn't have a "reg" property and
therefore must not have a unit-address, so drop it.
While at it, add missing unit-addresses for the charger and smart
battery IC's on the ChromeOS embedded controller's I2C tunnel bus.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Regulators defined at the top level in device tree are no longer part of
a simple bus and therefore don't have a reg property. Nodes without a
reg property shouldn't have a unit-address either, so drop the unit
address from the node names. To ensure nodes aren't duplicated (in which
case they would end up merged in the final DTB), append the name of the
regulator to the node name.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Clocks defined at the top level in device tree are no longer part of a
simple bus and therefore don't have a reg property. Nodes without a reg
property shouldn't have a unit-address either, so drop the unit address
from the node names. To ensure nodes aren't duplicated (in which case
they would end up merged in the final DTB), append the name of the clock
to the node name.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR controller needs the AVDD I/O and VDD HDMI PLL supplies in order
to operate correctly. Make sure to specify them for the Norrin board.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This panel supply is always on, so this does happen to work by accident.
Make sure to properly hook up the power supply to model the dependency
correctly and so that the panel continues to operate properly even if
the supply is not always on.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The standard way to do this is to list out the regulators at the top-
level. Adopt the standard way to fix validation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The standard way to do this is to list out the clocks at the top-level.
Adopt the standard way to fix validation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The new json-schema based validation tools require SD/MMC controller
nodes to be named mmc. Rename all references to them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The memory node requires a unit-address. For some boards the bootloader,
which is usually locked down, uses a hard-coded name for the memory node
without a unit-address, so we can't fix it on those boards.
Signed-off-by: Thierry Reding <treding@nvidia.com>
"simple-panel" is a Linux driver and has never been an accepted upstream
compatible string, so remove it.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Tegra boards, the device-tree alias serial0 is used for the console
and so add the stdout-path information so that the console no longer
needs to be passed via the kernel boot parameters.
For tegra132-norrin the alias serial0 is not defined and so add this.
This has been tested on tegra132-norrin and tegra210-p2371-0000.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "nvidia,wakeup-source" boolean property to enable the
wakeup source, "wakeup-source" is the new standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When Tegra124 support was first merged the unit-addresses of all devices
were listed with a "0," prefix to encode the reg property's second cell.
It turns out that this notation is not correct, and the "," separator is
only used to separate fields in the unit address (such as the device and
function number in PCI devices), not individual cells for addresses with
more than one cell.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The NVIDIA bootloader, nvtboot, expects the "chosen" node to be present
in the device-tree blob and if it is not then it fails to boot the kernel.
Add the chosen node so we can boot the kernel on Tegra132 Norrin with the
nvtboot bootloader.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Norrin is a Tegra132-based FFD used as reference platform within NVIDIA.
Based on work by Allen Martin <amartin@nvidia.com>
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Allen Martin <amartin@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
