The PMIC regulator node is missing regulator supplies. Now that the
binding supports them, add all the power rail supplies. Most of them
are fed from a system-wide semi-regulated power rail. A couple LDOs
are fed from the PMIC's own buck regulator outputs.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230928085537.3246669-13-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add basic device-tree for the Genio 1200-EVK board. This board
is made by MediaTek and has a MT8395 SoC (MT8195 family),
associated with the MT6359 and MT6360 PMICs, and
the MT7921 connectivity chip.
The IOs available on that board are:
* 1 USB Type-C connector with DP aux mode support
* 2 USB Type-A connector with a USB hub
* 1 micro-USB port for gadget or OTG support
* 1 full size HDMI RX and 1 full size HDMI TX connector
* 1 micro SD slot
* 40 pins header
* SPI interface header
* 1 M.2 slot
* 1 audio jack
* 1 micro-USB port for serial debug
* 2 connectors for DSI displays, 1 of the DSI panel is installed
* 3 connectors for CSI cameras
* 1 connector for a eDP panel
* 1 MMC storage
* 1 Touch Panel (installed DSI display)
* 1 M.2 slot for 5G dongle
This commit adds basic support in order to be able to boot.
Signed-off-by: Ben Lok <ben.lok@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230914055145.16801-2-macpaul.lin@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
AngeloGioacchino Del Regno is stepping in as co-maintainer for the
MediaTek SoC platform and starts by sending some dts fixes for
the mt8195 platform that had been pending for a while.
On the ixp4xx platform, Krzysztof Halasa steps down as co-maintainer,
reflecting that Linus Walleij has been handling this on his own
for the past few years.
Generic RISC-V kernels are now marked as incompatible with the
RZ/Five platform that requires custom hacks both for managing
its DMA bounce buffers and for addressing low virtual memory.
Finally, there is one bugfix for the AMDTEE firmware driver
to prevent a use-after-free bug.
-----BEGIN PGP SIGNATURE-----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=Ukoh
-----END PGP SIGNATURE-----
Merge tag 'soc-fixes-6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"AngeloGioacchino Del Regno is stepping in as co-maintainer for the
MediaTek SoC platform and starts by sending some dts fixes for the
mt8195 platform that had been pending for a while.
On the ixp4xx platform, Krzysztof Halasa steps down as co-maintainer,
reflecting that Linus Walleij has been handling this on his own for
the past few years.
Generic RISC-V kernels are now marked as incompatible with the RZ/Five
platform that requires custom hacks both for managing its DMA bounce
buffers and for addressing low virtual memory.
Finally, there is one bugfix for the AMDTEE firmware driver to prevent
a use-after-free bug"
* tag 'soc-fixes-6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
IXP4xx MAINTAINERS entries
arm64: dts: mediatek: mt8195: Set DSU PMU status to fail
arm64: dts: mediatek: fix t-phy unit name
arm64: dts: mediatek: mt8195-demo: update and reorder reserved memory regions
arm64: dts: mediatek: mt8195-demo: fix the memory size to 8GB
MAINTAINERS: Add Angelo as MediaTek SoC co-maintainer
soc: renesas: Make ARCH_R9A07G043 (riscv version) depend on NONPORTABLE
tee: amdtee: fix use-after-free vulnerability in amdtee_close_session
The DSU PMU allows monitoring performance events in the DSU cluster,
which is done by configuring and reading back values from the DSU PMU
system registers. However, for write-access to be allowed by ELs lower
than EL3, the EL3 firmware needs to update the setting on the ACTLR3_EL3
register, as it is disallowed by default.
That configuration is not done on the firmware used by the MT8195 SoC,
as a consequence, booting a MT8195-based machine like
mt8195-cherry-tomato-r2 with CONFIG_ARM_DSU_PMU enabled hangs the kernel
just as it writes to the CLUSTERPMOVSCLR_EL1 register, since the
instruction faults to EL3, and BL31 apparently just re-runs the
instruction over and over.
Mark the DSU PMU node in the Devicetree with status "fail", as the
machine doesn't have a suitable firmware to make use of it from the
kernel, and allowing its driver to probe would hang the kernel.
Fixes: 37f2582883 ("arm64: dts: Add mediatek SoC mt8195 and evaluation board")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230720200753.322133-1-nfraprado@collabora.com
Link: https://lore.kernel.org/r/20231003-mediatek-fixes-v6-7-v1-5-dad7cd62a8ff@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dtbs_check throws a warning at t-phy nodes:
Warning (unit_address_vs_reg): /t-phy@1a243000: node has a unit name, but no reg or ranges property
Warning (unit_address_vs_reg): /soc/t-phy@11c00000: node has a unit name, but no reg or ranges property
The ranges is empty thus removing the `@1a243000`, `@11c00000` from
the node name.
Fixes: 6029cae696 ("arm64: dts: mediatek: mt7622: harmonize node names and compatibles")
Fixes: 918aed7abd ("arm64: dts: mt7986: add pcie related device nodes")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230814093931.9298-2-eugen.hristev@collabora.com
Link: https://lore.kernel.org/r/20231003-mediatek-fixes-v6-7-v1-4-dad7cd62a8ff@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The dts file of the MediaTek MT8195 demo board has been updated to include
new reserved memory regions.
These reserved memory regions are:
- SCP
- VPU,
- Sound DMA
- APU.
These regions are defined with the "shared-dma-pool" compatible property.
In addition, the existing reserved memory regions have been reordered by
their addresses to improve readability and maintainability of the DTS
file.
Cc: stable@vger.kernel.org # 6.1, 6.4, 6.5
Fixes: e4a4175201 ("arm64: dts: mediatek: mt8195-demo: fix the memory size of node secmon")
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230905034511.11232-2-macpaul.lin@mediatek.com
Link: https://lore.kernel.org/r/20231003-mediatek-fixes-v6-7-v1-3-dad7cd62a8ff@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Align the node name with the definition in SCP bindings.
Signed-off-by: Tinghan Shen <tinghan.shen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20230901080935.14571-3-tinghan.shen@mediatek.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
"mediatek,merge-mute" and "mediatek,merge-fifo-en" properties are defined
and used as boolean properties which in DT have no value.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230830195650.704737-1-robh@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The defined value for "status" is "disabled", not "disable".
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230804225813.12493-1-robh@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The bootrom burned into the MT7986 SoC will try multiple locations on
the SPI-NAND flash to load bl2 in case the bl2 image located at the the
previously attempted offset is corrupt.
Use 0x100000 instead of 0x80000 as partition size for bl2 on SPI-NAND,
allowing for up to four redundant copies of bl2 (typically sized a
bit less than 0x40000).
Fixes: 8e01fb15b8 ("arm64: dts: mt7986: add Bananapi R3")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/ZH9UGF99RgzrHZ88@makrotopia.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the GPU's OPP table. This is from the downstream ChromeOS kernel,
adapted to the new upstream opp-supported-hw binning format. Also add
dynamic-power-coefficient for the GPU.
Also add label for mfg1 power domain. This is to be used at the board
level to add a regulator supply for the power domain.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230609072906.2784594-5-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
On the MT8186, the chip is binned for different GPU voltages at the
highest OPPs. The binning value is stored in the efuse.
Add the NVMEM cell, and tie it to the GPU.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230609072906.2784594-4-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds clocks, dynamic power coefficients, and OPP tables for the CPU
cores, so that everything required at the SoC level for CPU freqency and
voltage scaling is available.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230609072906.2784594-3-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a device node for the CCI (cache coherent interconnect) and an OPP
table for it. The OPP table was taken from the downstream ChromeOS
kernel.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230609072906.2784594-2-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add pwm-fan and cooling-maps to BananaPi-R3 devicetree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230530201235.22330-5-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add thermal-zones to mt7986 devicetree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230530201235.22330-4-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add thermal related nodes to mt7986 devicetree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230530201235.22330-3-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The capacity-dmips-mhz parameter was miscalculated: this SoC runs
the first (Cortex-A55) cluster at a maximum of 2000MHz and the
second (Cortex-A76) cluster at a maximum of 2200MHz.
In order to calculate the right capacity-dmips-mhz, the following
test was performed:
1. CPUFREQ governor was set to 'performance' on both clusters
2. Ran dhrystone with 500000000 iterations for 10 times on each cluster
3. Calculated the mean result for each cluster
4. Calculated DMIPS/MHz: dmips_mhz = dmips_per_second / cpu_mhz
5. Scaled results to 1024:
result_c0 = dmips_mhz_c0 / dmips_mhz_c1 * 1024
The mean results for this SoC are:
Cluster 0 (LITTLE): 12016411 Dhry/s
Cluster 1 (BIG): 31702034 Dhry/s
The calculated scaled results are:
Cluster 0: 426.953226899238 (rounded to 427)
Cluster 1: 1024
Fixes: 48489980e2 ("arm64: dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230602183515.3778780-1-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In the series "Adjust the dma-ranges for MTK IOMMU", the mtk-iommu
driver was adapted to separate the iova range based on the larb used,
and a dma-ranges property was added to the soc node in the devicetree of
the affected SoCs allowing the whole 16GB iova range to be used. Except
that for mt8192, there was no patch adding dma-ranges.
Add the missing dma-ranges property to the soc node like was done for
mt8195 and mt8186. This fixes the usage of the vcodec, which would
otherwise trigger iommu faults.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230601203221.3675915-1-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add video-codec lat and core nodes for mt8192 SoC.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230303013842.23259-4-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the cpufreq nodes for MT8192 SoC.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230317061944.15434-1-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Currently a specific panel number is used in the Elm DTSI, which is
corresponded to a 12" panel. However, according to the official Chrome
OS devices document, Elm refers to Acer Chromebook R13, which, as the
name specifies, uses a 13.3" panel, which comes with EDID information.
As the kernel currently prioritizes the hardcoded timing parameters
matched with the panel number compatible, a wrong timing will be applied
to the 13.3" panel on Acer Chromebook R13, which leads to blank display.
Because the Elm DTSI is shared with Hana board, and Hana corresponds to
multiple devices from 11" to 14", a certain panel model number shouldn't
be present, and driving the panel according to its EDID information is
necessary.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230526100801.16310-1-uwu@icenowy.me
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
To store uncompressed bl2 more space is required than partition is
actually defined.
There is currently no known usage of this reserved partition.
Openwrt uses same partition layout.
We added same change to u-boot with commit d7bb1099 [1].
[1] d7bb109900
Cc: stable@vger.kernel.org
Fixes: 8e01fb15b8 ("arm64: dts: mt7986: add Bananapi R3")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20230528113343.7649-1-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add "regulator-boot-on" to "panel_fixed_3v3" to save time on powering
the regulator during boot. Also add "off-on-delay-us" to the node to
make sure the regulator never violates the panel timing requirements.
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230417123956.926266-1-treapking@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Leds for Wifi are low-active, so add property to devicetree.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230205174833.107050-1-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds pwm node to mt7986.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20230421132047.42166-5-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The chassis-type string identifies the form-factor of the system:
add this property to all device trees of devices for which the form
factor is known.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230517101108.205654-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
As all level 2 and level 3 caches are unified, add required
cache-unified properties to fix warnings like:
mt7622-rfb1.dtb: l2-cache: 'cache-unified' is a required property
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230421223157.115367-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Firmware shipped on mt8195 Chromebooks is affected by the GICR
save/restore issue as described by the patch ("dt-bindings:
interrupt-controller: arm,gic-v3: Add quirk for Mediatek SoCs w/
broken FW"). Add the quirk property.
Fixes: 5eb2e303ec ("arm64: dts: mediatek: Introduce MT8195 Cherry platform's Tomato")
Reviewed-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230515131353.v2.5.Ia0b6ebbaa351e3cd67e201355b9ae67783c7d718@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Firmware shipped on mt8192 Chromebooks is affected by the GICR
save/restore issue as described by the patch ("dt-bindings:
interrupt-controller: arm,gic-v3: Add quirk for Mediatek SoCs w/
broken FW"). Add the quirk property.
Fixes: 331fae2fc9 ("arm64: dts: mediatek: Introduce MT8192-based Asurada board family")
Reviewed-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230515131353.v2.4.Ie7e600278ffbed55a1e5a58178203787b1449b35@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Firmware shipped on mt8183 Chromebooks is affected by the GICR
save/restore issue as described by the patch ("dt-bindings:
interrupt-controller: arm,gic-v3: Add quirk for Mediatek SoCs w/
broken FW"). Add the quirk property.
Fixes: cd894e274b ("arm64: dts: mt8183: Add krane-sku176 board")
Reviewed-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230515131353.v2.3.I525a2ed4260046d43c885ee1275e91707743df1c@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
On the Cherry platform, a MT7621 WiFi+Bluetooth combo is connected
over PCI-Express (for WiFi) and USB (for BT): enable the PCIe ports
to enable enumerating this chip.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230424112523.1436926-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Assign aliases for the primary and secondary dp-intf IP to properly
and reliably enable DisplayPort functionality.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230424112523.1436926-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Hayato's Realtek WiFi/BT module has it's Bluetooth function wired to
UART1.
Add and enable the relevant device nodes for it.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20230424100409.2992418-1-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Since commit ba751e28d4 ("net: dsa: mt7530: add interrupt support")
the mt7530 driver can act as an interrupt controller. Wire up irq line
of the MT7531 switch on the BananaPi BPi-R64 board, so the status of
the PHYs of the five 1000Base-T ports doesn't need to be polled any
more.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/ZEA-DV_OsmFg5egL@makrotopia.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The SPI-NOR node in the device tree of the BananaPi R64 has most likely
been copied from the reference board's device tree even though the R64
comes with an SPI-NAND chip rather than SPI-NOR.
Setup the Serial NAND Flash Interface (SNFI) controller, enable
hardware BCH error detection and correction engine and add the SPI-NAND
chip including basic partitions,
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/ZEA96dmaXqTpk8u8@makrotopia.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This smartphone uses the Helio X10 standard MT6331+MT6332 combo PMICs:
include the mt6331 devicetree and add the required interrupt.
Note that despite there being two interrupts, one for MT6331 and one
for MT6332, in configurations using the companion PMIC, the interrupt
of the latter fires for both events on MT6331 and for ones on MT6332,
while the interrupt for the main PMIC fires only for events of the
main PMIC.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230412112739.160376-25-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT6331 is the primary PMIC for the MediaTek Helio X10 MT6795 smartphone
platforms: add a devicetree describing its regulators, Real Time Clock
and PMIC-keys.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230412112739.160376-24-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add nodes for the multimedia IOMMU and its LARBs: this includes all but
the MJC LARB, which cannot currently be used and will be added later.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230412112739.160376-19-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add AP Domain thermal zones for the mt8195 and
specify the targeted temperature thresholds.
Signed-off-by: Balsam CHIHI <bchihi@baylibre.com>
Link: https://lore.kernel.org/r/20230405100907.53740-1-bchihi@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add display nodes and the GCE (Global Command Engine) properties
to the display nodes in order to enable the usage of the CMDQ
(Command Queue), which is required for operating the display.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230324021258.15863-7-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the Global Command Engine (GCE) node for MT8186 SoC
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230324021258.15863-6-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In order to have cpufreq support, this patch adds proc-supply and
sram-supply for each CPU.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230203-evk-board-support-v8-9-7019f3fd0adf@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In order to have cpufreq support, this patch adds generic Operating
Performance Points support.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230203-evk-board-support-v8-8-7019f3fd0adf@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
- Enable "vibr" and "vsim2" regulators to power the ethernet chip.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230203-evk-board-support-v8-7-7019f3fd0adf@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch add support for SuperSpeed USB, in OTG mode, on micro connector.
It also add support for the Extensible Host Controller Interface USB.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230203-evk-board-support-v8-6-7019f3fd0adf@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
- Add EMMC support on mmc0 (internal memory)
- Add SD-UHS support on mmc1 (external memory)
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230203-evk-board-support-v8-5-7019f3fd0adf@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This power management system chip integration helps to manage regulators
and keys.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230203-evk-board-support-v8-4-7019f3fd0adf@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Including:
- Convert to platform remove callback returning void
- Extend changing default domain to normal group
- Intel VT-d updates:
- Remove VT-d virtual command interface and IOASID
- Allow the VT-d driver to support non-PRI IOPF
- Remove PASID supervisor request support
- Various small and misc cleanups
- ARM SMMU updates:
- Device-tree binding updates:
* Allow Qualcomm GPU SMMUs to accept relevant clock properties
* Document Qualcomm 8550 SoC as implementing an MMU-500
* Favour new "qcom,smmu-500" binding for Adreno SMMUs
- Fix S2CR quirk detection on non-architectural Qualcomm SMMU
implementations
- Acknowledge SMMUv3 PRI queue overflow when consuming events
- Document (in a comment) why ATS is disabled for bypass streams
- AMD IOMMU updates:
- 5-level page-table support
- NUMA awareness for memory allocations
- Unisoc driver: Support for reattaching an existing domain
- Rockchip driver: Add missing set_platform_dma_ops callback
- Mediatek driver: Adjust the dma-ranges
- Various other small fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=OvTo
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Convert to platform remove callback returning void
- Extend changing default domain to normal group
- Intel VT-d updates:
- Remove VT-d virtual command interface and IOASID
- Allow the VT-d driver to support non-PRI IOPF
- Remove PASID supervisor request support
- Various small and misc cleanups
- ARM SMMU updates:
- Device-tree binding updates:
* Allow Qualcomm GPU SMMUs to accept relevant clock properties
* Document Qualcomm 8550 SoC as implementing an MMU-500
* Favour new "qcom,smmu-500" binding for Adreno SMMUs
- Fix S2CR quirk detection on non-architectural Qualcomm SMMU
implementations
- Acknowledge SMMUv3 PRI queue overflow when consuming events
- Document (in a comment) why ATS is disabled for bypass streams
- AMD IOMMU updates:
- 5-level page-table support
- NUMA awareness for memory allocations
- Unisoc driver: Support for reattaching an existing domain
- Rockchip driver: Add missing set_platform_dma_ops callback
- Mediatek driver: Adjust the dma-ranges
- Various other small fixes and cleanups
* tag 'iommu-updates-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (82 commits)
iommu: Remove iommu_group_get_by_id()
iommu: Make iommu_release_device() static
iommu/vt-d: Remove BUG_ON in dmar_insert_dev_scope()
iommu/vt-d: Remove a useless BUG_ON(dev->is_virtfn)
iommu/vt-d: Remove BUG_ON in map/unmap()
iommu/vt-d: Remove BUG_ON when domain->pgd is NULL
iommu/vt-d: Remove BUG_ON in handling iotlb cache invalidation
iommu/vt-d: Remove BUG_ON on checking valid pfn range
iommu/vt-d: Make size of operands same in bitwise operations
iommu/vt-d: Remove PASID supervisor request support
iommu/vt-d: Use non-privileged mode for all PASIDs
iommu/vt-d: Remove extern from function prototypes
iommu/vt-d: Do not use GFP_ATOMIC when not needed
iommu/vt-d: Remove unnecessary checks in iopf disabling path
iommu/vt-d: Move PRI handling to IOPF feature path
iommu/vt-d: Move pfsid and ats_qdep calculation to device probe path
iommu/vt-d: Move iopf code from SVA to IOPF enabling path
iommu/vt-d: Allow SVA with device-specific IOPF
dmaengine: idxd: Add enable/disable device IOPF feature
arm64: dts: mt8186: Add dma-ranges for the parent "soc" node
...
Prepare for the MM nodes whose dma-ranges(iova range) is 16GB.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230411093144.2690-15-yong.wu@mediatek.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
After commit f1ad5338a4 ("of: Fix "dma-ranges" handling for bus
controllers"), the dma-ranges property is not allowed for
the leaf node. But our iommu/dma-ranges is 16GB, we still expect
separate the 16GB dma-range like:
a) display is in 0 - 4GB;
b) vcodec is in 4GB - 8GB;
c) camera is in 8GB - 12GB.
We can not expect all the masters add a parent node for them,
especial for the existed drivers/nodes.
Thus, we add whole the 16GB dma-ranges in the parent "soc" node.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230411093144.2690-14-yong.wu@mediatek.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
After we add the dma-ranges in the parent "soc" node,
this property is unnecessary for the leaf node.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230411093144.2690-13-yong.wu@mediatek.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This smartphone features a Bosch BMM050 Magnetometer on I2C3: enable
it with the BMM150 binding, as that driver supports BMM050 as well.
For this sensor, there is no interrupt pin;
readings were validated in sysfs.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230412112739.160376-28-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The PWM at 0x11006000 is the tertiary PWM; unlike PWM0, PWM1, this is
not display specific and can be used as a generic PWM controller.
This node is left disabled as usage is board-specific.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230412112739.160376-21-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In prepration for adding the IOMMUs and LARBs of this SoC, add the
VDECSYS and VENCSYS clock controller nodes, providing clocks for the
vcodec stateful decoder and stateful decoder hardware.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230327083647.22017-11-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable FHCTL with Spread Spectrum for MAINPLL, MPLL and MSDCPLL
as found on the downstream kernel for this smartphone.
Which one to enable, and at what SSC percentage, was found by
dumping the debugging data from a running downstream kernel and
checking the downstream code.
/proc/freqhopping # cat status
FH status:
===============================================
id == fh_status == pll_status == setting_id == curr_freq == user_defined
0 0 1 0 1599000 0
1 0 1 0 1716000 0
2 1 1 2 1092000 0
3 1 1 2 2912000 0
4 1 0 2 1600000 0
5 0 0 0 0 0
6 0 1 0 1518002 0
7 0 0 0 0 0
8 0 0 0 0 0
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230327083647.22017-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add FHCTL node but keep it disabled as the PLL clocks that should be
handled through FHCTL and the Spread Spectrum Clocking parameters are
board specific.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230327083647.22017-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Configure the hardware PWM for the integrated display's backlight:
all Cherry devices enable the backlight with GPIO82 and manage the
PWM via MediaTek disp-pwm on GPIO97.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230223145426.193590-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the two hardware PWMs for display backlighting but keep them
disabled by default, as usage is board-specific.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230223145426.193590-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The mt8195 SoC has several hotspots around the CPUs. Specify the
targeted temperature threshold when to apply the mitigation and define
the associated cooling devices.
Signed-off-by: Balsam CHIHI <bchihi@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230209105628.50294-7-bchihi@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add thermal zones and thermal nodes for the mt8195.
Signed-off-by: Balsam CHIHI <bchihi@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230209105628.50294-6-bchihi@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This IP is a 10/100 MAC controller compliant with IEEE 802.3 standards.
It supports power management with Energy Efficient Ethernet and Wake-on-LAN
specification. Flow control is provided for half-duplex and full-duplex
mode. For packet transmission and reception, the controller supports
IPv4/UDP/TCP checksum offload and VLAN tag insertion.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230203-evk-board-support-v3-12-0003e80e0095@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In order to use the PMIC, the pwrap support should be added
to allow communication between the SoC and the PMIC.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230203-evk-board-support-v3-6-0003e80e0095@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This new device-tree add the regulators, rtc and keys support
for the MT6357 PMIC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230203-evk-board-support-v3-5-0003e80e0095@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The reserved size for BL31 is too small.
This has been highlighted by the MPU that now restrict access to BL31
memory to secure world only.
This increase the size of the reserved memory.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230203-evk-board-support-v3-3-0003e80e0095@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable the I2C0 bus provides communication with:
- The integrated RT9466 Switching Battery Charger.
- The integrated MT6691 LP4X buck for VDDQ.
- The integrated MT6691 LP4X buck for VDD2.
- The pin header, to plug external I2C devices.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221122-mt8365-i2c-support-v6-2-e1009c8afd53@baylibre.com
[mb: move bias-pull-up below pinmux]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
There are four I2C master channels in MT8365 with a same HW architecture.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20221122-mt8365-i2c-support-v6-1-e1009c8afd53@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Override the PMIC-default voltage constraints for VGPU and VSRAM_GPU
with the platform specific vmin/vmax for the highest possible SoC
binning.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Suggested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-20-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Override the PMIC-default voltage constraints for VGPU and VSRAM_GPU
with the platform specific vmin/vmax for the highest possible SoC
binning.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Suggested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-19-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a GPU node for MT8186 SoC but keep it disabled.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-18-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable the Mali-G57 found on this platform with the open-source
Panfrost driver.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-17-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add GPU support through panfrost for the Mali-G57 GPU on MT8195
with its OPP table but keep it in disabled state.
This is expected to be enabled only on boards which make use of
the GPU.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-16-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Similarly to what can be seen in MT8192, on MT8195 the mfg_core_tmp
clock is a mux used to switch between different "safe" (and slower)
clock sources for the GPU: this is used during MFGPLL reconfiguration
and eventually during idling at very low frequencies.
This clock getting turned off means that the GPU will occasionally be
unclocked, producing obvious consequences such as system crash or
unpredictable behavior: assigning it to the top level MFG power domain
will make sure that this stays on at all times during any operation on
the MFG domain (only GPU-related transactions).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-15-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable the GPU with its power supplies described.
Signed-off-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
[wenst@: patch split out from MT8192 GPU node patch]
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
[Angelo: Minor commit title fix]
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-14-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add coupling for these regulators, as VSRAM_OTHER is used to power the
GPU SRAM, and they have a strict voltage output relation to satisfy in
order to ensure GPU stable operation.
While at it, also add voltage constraint overrides for the GPU SRAM
regulator "mt6359_vsram_others" so that we stay in a safe range of
0.75-0.80V.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-13-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The MT8192 SoC specifies a maximum voltage for the GPU's digital supply
of 0.88V and the GPU OPPs are declaring a maximum voltage of 0.80V.
In order to keep the GPU voltage in the safe range, change the maximum
voltage for mt6315@7's vbuck1 to 0.80V as sending, for any mistake,
1.193V would be catastrophic.
Fixes: 3183cb62b0 ("arm64: dts: mediatek: asurada: Add SPMI regulators")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-12-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a phandle to the MT8192_POWER_DOMAIN_MFG1 power domain and
assign the GPU VSRAM supply to this in mt8192-asurada: this allows to
keep the sram powered up while the GPU is used.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-11-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The mfg0 power domain encompasses the whole GPU and its surrounding
glue logic. This power domain has a separate power rail.
Add its power supply for Asurada.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
[wenst@chromium.org: fix subject prefix and add commit message]
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
[Angelo: Reordered commits to address DVFS stability issues]
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-10-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The mfg_ref_sel clock is a mux used to switch between different "safe"
(and slower) clock sources for the GPU: this is used during MFGPLL
reconfiguration and eventually during idling at very low frequencies.
This clock getting turned off means that the GPU will occasionally be
unclocked, producing obvious consequences such as system crash or
unpredictable behavior: assigning it to the top level MFG power domain
will make sure that this stays on at all times during any operation on
the MFG domain (only GPU-related transactions).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-9-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The MediaTek MT8192 includes a Mali-G57 GPU supported in Panfrost. Add
the GPU node to the device tree to enable 3D acceleration.
The GPU node is disabled by default. It should be enabled by board with
its power supplies correctly assigned.
Signed-off-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
[nfraprado: removed sram supply, tweaked opp node name, adjusted commit message]
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
[wenst@: disable GPU by default; adjusted prefix; split out board change]
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
[Angelo: cosmetic fixes]
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-8-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Use the new GPU related compatible to finally enable GPU DVFS on
the MT8183 SoC.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-7-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add coupling for these regulators, as they have a strict voltage output
relation to satisfy in order to ensure GPU stable operation.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add coupling for these regulators, as they have a strict voltage output
relation to satisfy in order to ensure GPU stable operation.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This was done to keep a strict relation between VSRAM and VGPU, but
it never worked: now we're doing it transparently with the new
mediatek-regulator-coupler driver.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Override the PMIC-default voltage constraints for VGPU and VSRAM_GPU
with the platform specific vmin/vmax for the highest possible SoC
binning.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add coupling for these regulators, as they have a strict voltage output
relation to satisfy in order to ensure GPU stable operation.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230301095523.428461-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds minimal support for the Mediatek 8365 SOC and the EVK reference
board, allowing the board to boot to initramfs with serial port I/O.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
[bero@baylibre.com: Removed parts depending on drivers that aren't upstream yet, cleanups, add CPU cache layout, add systimer, fix GIC]
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
[aouledameur@baylibre.com: Fix systimer properties]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230309213501.794764-4-bero@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The node name should be generic and mmsys expcets 'syscon'
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230209160357.19307-2-matthias.bgg@kernel.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In MT8195, the MMSYS has two Video Processor Pipepline Subsystems
named VPPSYS0 and VPPSYS1, each with specific MUTEX to control
Start of Frame(SOF) and End of Frame (EOF) signals.
Before working with them, the addresses, interrupts, clocks and power
domains need to be set up in dts.
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230206091109.1324-4-moudy.ho@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
With the change of the MMSYS binding file for MT8195, the compatible
name of VPPSYS in dts need to be fixed to match the definition.
Signed-off-by: Roy-CW.Yeh <roy-cw.yeh@mediatek.com>
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230206091109.1324-3-moudy.ho@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Change the existing node name in order to match NAND controller DT
bindings.
Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230201021500.26769-3-xiangsheng.hou@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
About a quarter of the changes are for 32-bit arm, mostly filling in
device support for existing machines and adding minor cleanups, mostly
for Qualcomm and Samsung based machines.
Two new 32-bit SoCs are added, both are quad-core Cortex-A7 chips from
Rockchips that have been around for a while but were lacking kernel
support so far: RV1126 is a Vision SoC with an NPU and is used in the
Edgeble Neural Compute Module 2(Neu2) board, while RK3128 is design for
TV boxes and so far only comes with a dts for its refernece design.
The other 32-bit boards that were added are two ASpeed AST2600 based BMC
boards, the Microchip sam9x60_curiosity development board (Armv5 based!),
the Enclustra PE1 FPGA-SoM baseboard, and a few more boards for i.MX53
and i.MX6ULL.
On the RISC-V side, there are fewer patches, but a total of ten new
single-board computers based on variations of the Allwinner D1/T113 chip,
plus one more board based on Microchip Polarfire.
As usual, arm64 has by far the most changes here, with over 700 non-merge
changesets, among them over 400 alone for Qualcomm. The newly added SoCs
this time are all recent high-end embedded SoCs for various markets,
each on comes with support for its reference board:
- Qualcomm SM8550 (Snapdragon 8 Gen 2) for mobile phones
- Qualcomm QDU1000/QRU1000 5G RAN platform
- Rockchips RK3588/RK3588s for tablets, chromebooks and SBCs
- TI J784S4 for industrial and automotive applications
In total, there are 46 new arm64 machines:
- Reference platforms for each of the five new SoCs
- Three Amlogic based development boards
- Six embedded machines based on NXP i.MX8MM and i.MX8MP
- The Mediatek mt7986a based Banana Pi R3 router
- Six tablets based on Qualcomm MSM8916 (Snapdragon 410),
SM6115 (Snapdragon 662) and SM8250 (Snapdragon 865)
- Two LTE dongles, also based on MSM8916
- Seven mobile phones, based on Qualcomm MSM8953 (Snapdragon 610),
SDM450 and SDM632
- Three chromebooks based on Qualcomm SC7280 (Snapdragon 7c)
- Nine development boards based on Rockchips RK3588, RK3568,
RK3566 and RK3328.
- Five development machines based on TI K3 (AM642/AM654/AM68/AM69)
The cleanup of dtc warnings continues across all platforms, adding
to the total number of changes.
-----BEGIN PGP SIGNATURE-----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=I8Ga
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC DT updates from Arnd Bergmann:
"About a quarter of the changes are for 32-bit arm, mostly filling in
device support for existing machines and adding minor cleanups, mostly
for Qualcomm and Samsung based machines.
Two new 32-bit SoCs are added, both are quad-core Cortex-A7 chips from
Rockchips that have been around for a while but were lacking kernel
support so far: RV1126 is a Vision SoC with an NPU and is used in the
Edgeble Neural Compute Module 2(Neu2) board, while RK3128 is design
for TV boxes and so far only comes with a dts for its refernece
design.
The other 32-bit boards that were added are two ASpeed AST2600 based
BMC boards, the Microchip sam9x60_curiosity development board (Armv5
based!), the Enclustra PE1 FPGA-SoM baseboard, and a few more boards
for i.MX53 and i.MX6ULL.
On the RISC-V side, there are fewer patches, but a total of ten new
single-board computers based on variations of the Allwinner D1/T113
chip, plus one more board based on Microchip Polarfire.
As usual, arm64 has by far the most changes here, with over 700
non-merge changesets, among them over 400 alone for Qualcomm. The
newly added SoCs this time are all recent high-end embedded SoCs for
various markets, each on comes with support for its reference board:
- Qualcomm SM8550 (Snapdragon 8 Gen 2) for mobile phones
- Qualcomm QDU1000/QRU1000 5G RAN platform
- Rockchips RK3588/RK3588s for tablets, chromebooks and SBCs
- TI J784S4 for industrial and automotive applications
In total, there are 46 new arm64 machines:
- Reference platforms for each of the five new SoCs
- Three Amlogic based development boards
- Six embedded machines based on NXP i.MX8MM and i.MX8MP
- The Mediatek mt7986a based Banana Pi R3 router
- Six tablets based on Qualcomm MSM8916 (Snapdragon 410), SM6115
(Snapdragon 662) and SM8250 (Snapdragon 865)
- Two LTE dongles, also based on MSM8916
- Seven mobile phones, based on Qualcomm MSM8953 (Snapdragon 610),
SDM450 and SDM632
- Three chromebooks based on Qualcomm SC7280 (Snapdragon 7c)
- Nine development boards based on Rockchips RK3588, RK3568, RK3566
and RK3328.
- Five development machines based on TI K3 (AM642/AM654/AM68/AM69)
The cleanup of dtc warnings continues across all platforms, adding to
the total number of changes"
* tag 'soc-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (1035 commits)
dt-bindings: riscv: correct starfive visionfive 2 compatibles
ARM: dts: socfpga: Add enclustra PE1 devicetree
dt-bindings: altera: Add enclustra mercury PE1
arm64: dts: qcom: msm8996: align RPM G-Link clock-controller node with bindings
arm64: dts: qcom: qcs404: align RPM G-Link node with bindings
arm64: dts: qcom: ipq6018: align RPM G-Link node with bindings
arm64: dts: qcom: sm8550: remove invalid interconnect property from cryptobam
arm64: dts: qcom: sc7280: Adjust zombie PWM frequency
arm64: dts: qcom: sc8280xp-pmics: Specify interrupt parent explicitly
arm64: dts: qcom: sm7225-fairphone-fp4: enable remaining i2c busses
arm64: dts: qcom: sm7225-fairphone-fp4: move status property down
arm64: dts: qcom: pmk8350: Use the correct PON compatible
arm64: dts: qcom: sc8280xp-x13s: Enable external display
arm64: dts: qcom: sc8280xp-crd: Introduce pmic_glink
arm64: dts: qcom: sc8280xp: Add USB-C-related DP blocks
arm64: dts: qcom: sm8350-hdk: enable GPU
arm64: dts: qcom: sm8350: add GPU, GMU, GPU CC and SMMU nodes
arm64: dts: qcom: sm8350: finish reordering nodes
arm64: dts: qcom: sm8350: move more nodes to correct place
arm64: dts: qcom: sm8350: reorder device nodes
...
When vdosys1 was initially added, it was incorrectly assumed to be
compatible with vdosys0, and thus both had the same mt8195-mmsys
compatible attached.
This has since been corrected in commit b237efd47d ("dt-bindings:
arm: mediatek: mmsys: change compatible for MT8195") and commit
82219cfbef ("dt-bindings: arm: mediatek: mmsys: add vdosys1 compatible
for MT8195"). The device tree needs to be fixed as well, otherwise
the vdosys1 block fails to work, and causes its dependent power domain
controller to not work either.
Change the compatible string of vdosys1 to "mediatek,mt8195-vdosys1".
While at it, also add the new "mediatek,mt8195-vdosys0" compatible to
vdosys0.
Fixes: 6aa5b46d17 ("arm64: dts: mt8195: Add vdosys and vppsys clock nodes")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20230202104014.2931517-1-wenst@chromium.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The proper name is 'watchdog', not 'toprgu' and remove the unused
label.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20221108033209.22751-5-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT7986's watchdog embeds a reset controller and needs only the
mediatek,mt7986-wdt compatible string as the MT6589 one is there
for watchdogs that don't have any reset controller capability.
Fixes: 50137c150f ("arm64: dts: mediatek: add basic mt7986 support")
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20221108033209.22751-4-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT8195's watchdog embeds a reset controller and needs only the
mediatek,mt8195-wdt compatible string as the MT6589 one is there
for watchdogs that don't have any reset controller capability.
Fixes: 37f2582883 ("arm64: dts: Add mediatek SoC mt8195 and evaluation board")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Co-developed-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20221108033209.22751-3-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT8186's watchdog embeds a reset controller and needs only the
mediatek,mt8186-wdt compatible string as the MT6589 one is there
for watchdogs that don't have any reset controller capability.
Fixes: 2e78620b13 ("arm64: dts: Add MediaTek MT8186 dts and evaluation board and Makefile")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Co-developed-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20221108033209.22751-2-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The names of the idle states are misleading being this a single cluster
SoC, a cluster-sleep idle state is impossible!
After some research in ATF, it emerged that the cpu-sleep state is in
reality putting CPUs in retention state, while the cluster-sleep one
is turning off the CPUs.
Summarizing renaming:
- cpu-sleep -> cpu-retention
- cluster-sleep -> cpu-off
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230126103526.417039-7-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The names of the idle states are misleading being this a single cluster
SoC, a cluster-off idle state is impossible!
After some research in ATF, it emerged that the cpu-off state is in
reality putting CPUs in retention state, while the cluster-off one
is turning off the CPUs.
Summarizing renaming:
- cpu-off -> cpu-retention
- cluster-off -> cpu-off
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230126103526.417039-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The names of the idle states are misleading being this a single cluster
SoC, a cluster-off idle state is impossible!
After some research in ATF, it emerged that the cpu-off state is in
reality putting CPUs in retention state, while the cluster-off one
is turning off the CPUs.
Summarizing renaming:
- cpu-off -> cpu-retention
- cluster-off -> cpu-off
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230126103526.417039-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT8186 features the ARM DynamIQ technology and combines both two
Cortex-A76 (big) and six Cortex-A55 (LITTLE) CPUs in one cluster:
fix the CPU map to reflect that.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Fixes: 2e78620b13 ("arm64: dts: Add MediaTek MT8186 dts and evaluation board and Makefile")
Link: https://lore.kernel.org/r/20230126103526.417039-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT8192 features the ARM DynamIQ technology and combines both four
Cortex-A76 (big) and four Cortex-A55 (LITTLE) CPUs in one cluster:
fix the CPU map to reflect that.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Fixes: 48489980e2 ("arm64: dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile")
Link: https://lore.kernel.org/r/20230126103526.417039-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT8195 features the ARM DynamIQ technology and combines both four
Cortex-A78 (big) and four Cortex-A55 (LITTLE) CPUs in one cluster:
fix the CPU map to reflect that.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Fixes: 37f2582883 ("arm64: dts: Add mediatek SoC mt8195 and evaluation board")
Link: https://lore.kernel.org/r/20230126103526.417039-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The DTSI comes with interrupts property, so it must be removed if
interrupts-extended are used:
mt8183-kukui-jacuzzi-cozmo.dtb: serial@11003000: More than one condition true in oneOf schema:
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230123151634.370011-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The serial node does not use clock-names:
mt7622-bananapi-bpi-r64.dtb: serial@1100c000: Unevaluated properties are not allowed ('clock-names' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230123151634.370011-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add efuse node.
This will be required by the thermal driver to get the calibration data.
Signed-off-by: Balsam CHIHI <bchihi@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230124131717.128660-4-bchihi@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Read edp panel edid through aux bus, which is a more preferred way. Also
use a more generic compatible since each jacuzzi models use different
panels.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20221228113204.1551180-1-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The scp_adsp clock controller is under the SCP_ADSP power domain. This
power domain is currently not supported nor defined.
Mark the clock controller as broken for now, to avoid the system from
trying to access it, and causing the CPU or bus to stall.
Fixes: 5d2b897bc6 ("arm64: dts: mediatek: Add mt8192 clock controllers")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20221229101202.1655924-1-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
- Change the node name from "mt6397" to "pmic" to be consistent
with the generic names recommendation.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221005-mt6357-support-v8-5-560caaafee53@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
- Change the node name from "mt6358" to "pmic", "mt6358rtc" to "rtc" and
"mt6358keys" to "keys" to be consistent with the generic names recommendation.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221005-mt6357-support-v8-4-560caaafee53@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add support for Bananapi R3 SBC.
- SD/eMMC support (switching first 4 bits of data-bus with sw6/D)
- SPI-NAND/NOR support (switched CS by sw5/C)
- all rj45 ports and both SFP working (eth1/lan4)
- all USB-Ports + SIM-Slot tested
- i2c and all uarts tested
- wifi tested (with eeprom calibration data)
The device can boot from all 4 storage options. Both, SPI and MMC, can
be switched using hardware switches on the board, see
https://wiki.banana-pi.org/Banana_Pi_BPI-R3#Jumper_setting
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20230106152845.88717-6-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds PCIe support for MT7986.
Signed-off-by: Jieyy Yang <jieyy.yang@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230106152845.88717-5-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds mmc support for MT7986.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20230106152845.88717-4-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds USB support for MT7986.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20230106152845.88717-3-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
For crypto support, add a crypto clock of the inline crypto engine and
expand the register size in the eMMC controller.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Link: https://lore.kernel.org/r/20221221104856.28770-1-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The entire Cherry family has two digital microphones, for which
we use the generic dmic-codec, linked to the MT6359 PMIC.
Moreover, it uses a Realtek RT1019p amplifier for the speakers
and has either a Realtek RT5682i or RT5682s audio codec on I2C2:
specifically, RT5682i is found on Tomato's rev 1 and rev 2 boards,
while RT5682s is found in rev3 and rev4 boards.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220922094908.41623-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This platform is able to use the Audio DSP embedded into the
MT8195 SoC: in preparation for adding audio support for Cherry,
add the ADSP related memory nodes and enable it.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220922094908.41623-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In preparation for adding audio support, enable the AFE HW with
the appropriate eTDM configuration and memory region.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220922094908.41623-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The node names should be generic and DT schema expects certain pattern:
mediatek/mt8183-kukui-jacuzzi-fennel-sku1.dtb: pwmleds: 'keyboard-backlight' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221125144138.477198-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add aliases for the i2c and mmc nodes on the Asurada platform DT to
ensure that we get stable ids for those devices on userspace.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20221102190611.283546-6-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable audio support for the Asurada platform. This consists of the
machine sound card, the rt1015p codec for the speakers, the rt5682 codec
for the headset, and the dmic codec for the internal microphone.
Newer revisions of spherion and hayato use the rt5682s codec for the
headset instead, so the codecs and card compatible are added through
separate dtsi files to prepare for that.
HDMI audio support is left out for now since the DisplayPort chip
required isn't enabled yet.
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221102190611.283546-5-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The asurada platform has an ANX7625 bridge connecting the DSI's output
to the internal eDP panel. Add and enable these devices in order to get
a usable internal display.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20221102190611.283546-4-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the display backlight for the Asurada platform. It relies on the
display PWM controller, so also enable and configure this component.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20221102190611.283546-3-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the regulators present on the Asurada platform that are used to
power the internal and external displays.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20221102190611.283546-2-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This SoC's AP subsystem has 8x Cortex-A53 CPUs, specifically,
four CPUs per cluster, with two CPU clusters.
Each CPU has:
- A 32KB I-cache, 2-way set associative;
- A 32KB D-cache, 4-way set associative.
Each cluster has a unified 1MB L2 cache, 16-way set associative.
With that in mind, add the appropriate properties needed to specify the
caches information for this SoC, which will now be correctly exported
to sysfs.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221206112330.78431-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This SoC features two clusters composed of:
- 4x Cortex A53: 32KB I-cache, 2-way set associative,
32KB D-cache, 4-way set associative,
unified 1MB L2 cache, 16-way set associative;
- 4x Cortex A73: 64KB I-cache and 64KB D-cache, 4-way set associative,
unified 1MB L2 cache, 16-way set associative;
With that in mind, add the appropriate properties needed to specify the
caches information for this SoC, which will now be correctly exported
to sysfs.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221206112330.78431-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This SoC features two clusters composed of:
- 6x Cortex A55: 32KB I-cache and 32KB D-cache, 4-way set associative,
per-cpu 128KB L2 cache, 4-way set associative;
- 2x Cortex A76: 64KB I-cache and 64KB D-cache, 4-way set associative,
per-cpu 256KB L2 cache, 8-way set associative;
Moreover, the two clusters are sharing a DSU L3 cache with size 1MB,
16-way set associative.
With that in mind, add the appropriate properties needed to specify the
caches information for this SoC, which will now be correctly exported
to sysfs.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221206112330.78431-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This SoC features two clusters composed of:
- 4x Cortex A55: 32KB I-cache and 32KB D-cache, 4-way set associative,
per-cpu 128KB L2 cache, 4-way set associative;
- 4x Cortex A76: 64KB I-cache and 64KB D-cache, 4-way set associative,
per-cpu 256KB L2 cache, 8-way set associative;
Moreover, the two clusters are sharing a DSU L3 cache with size 2MB,
16-way set associative.
With that in mind, add the appropriate properties needed to specify the
caches information for this SoC, which will now be correctly exported
to sysfs.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221206112330.78431-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This SoC features two clusters composed of:
- 4x Cortex A55: 32KB I-cache and 32KB D-cache, 4-way set associative,
per-cpu 128KB L2 cache, 4-way set associative;
- 4x Cortex A78: 64KB I-cache and 64KB D-cache, 4-way set associative,
per-cpu 256KB L2 cache, 8-way set associative;
Moreover, the two clusters are sharing a DSU L3 cache with size 2MB,
16-way set associative.
With that in mind, add the appropriate properties needed to specify the
caches information for this SoC, which will now be correctly exported
to sysfs.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221206112330.78431-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Remove the unnecessary pins-are-numbered property from
arm64 Mediatek DeviceTrees
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20221129023401.278780-6-bero@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The systimer block derives its 13 MHz clock by dividing the main 26 MHz
oscillator clock by 2 internally. The 13 MHz clock is not a separate
oscillator.
Fix this by making the 13 MHz clock a divide-by-2 fixed factor clock,
taking its input from the main 26 MHz oscillator.
Fixes: 2e78620b13 ("arm64: dts: Add MediaTek MT8186 dts and evaluation board and Makefile")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221201084229.3464449-5-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The systimer block derives its 13 MHz clock by dividing the main 26 MHz
oscillator clock by 2 internally, not through the TOPCKGEN clock
controller.
On the MT8195 this divider is set either by power-on-reset or by the
bootloader. The bootloader may then make the divider unconfigurable to,
but can be read out by, the operating system.
Making the systimer block take the 26 MHz clock directly requires
changing the implementations. As an ABI compatible fix, change the
input clock of the systimer block a fixed factor divide-by-2 clock
that takes the 26 MHz oscillator as its input.
Fixes: 37f2582883 ("arm64: dts: Add mediatek SoC mt8195 and evaluation board")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221201084229.3464449-4-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The systimer block derives its 13 MHz clock by dividing the main 26 MHz
oscillator clock by 2 internally, not through the TOPCKGEN clock
controller.
On the MT8192 this divider is fixed to /2 and is not configurable.
Making the systimer block take the 26 MHz clock directly requires
changing the implementations. As an ABI compatible fix, change the
input clock of the systimer block a fixed factor divide-by-2 clock
that takes the 26 MHz oscillator as its input.
Fixes: 48489980e2 ("arm64: dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221201084229.3464449-3-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The systimer block derives its 13 MHz clock by dividing the main 26 MHz
oscillator clock by 2 internally, not through the TOPCKGEN clock
controller.
On the MT8183 this divider is set either by power-on-reset or by the
bootloader. The bootloader may then make the divider unconfigurable to,
but can be read out by, the operating system.
Making the systimer block take the 26 MHz clock directly requires
changing the implementations. As an ABI compatible fix, change the
input clock of the systimer block a fixed factor divide-by-2 clock
that takes the 26 MHz oscillator as its input.
Fixes: 5bc8e2875f ("arm64: dts: mt8183: add systimer0 device node")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221201084229.3464449-2-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Assign power domain to the U3PHY1 T-PHY in otder to keep this PHY
alive after unused PD shutdown and to be able to completely cut
and restore power to it, for example, to save some power during
system suspend/sleep.
Fixes: 2b515194bf ("arm64: dts: mt8195: Add power domains controller")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221214131117.108008-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Despite there being some flexibility regarding the P0/P1 connections,
especially for TL and PERI, we must use P1 clocks on pcie1 otherwise
we'll be dealing with unclocked access.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221214131117.108008-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Kukui devices krane, kodana, and kakadu use detachable keyboards, which
only have switches to be registered.
Change the keyboard node's compatible of those boards to the newly
introduced "google,cros-ec-keyb-switches", which won't include matrix
properties.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20220527045353.2483042-1-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
These are a couple of build fixes from randconfig testing,
plus a set of Mediatek SoC specific fixes, all trivial.
-----BEGIN PGP SIGNATURE-----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=qUCm
-----END PGP SIGNATURE-----
Merge tag 'soc-fixes-6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"These are a couple of build fixes from randconfig testing, plus a set
of Mediatek SoC specific fixes, all trivial"
* tag 'soc-fixes-6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
soc: tegra: fix CPU_BIG_ENDIAN dependencies
ARM: disallow pre-ARMv5 builds with ld.lld
ARM: pxa: fix building with clang
MAINTAINERS: add related dts to IXP4xx
ARM: dts: spear: drop 0x from unit address
arm64: dts: mt8183: Fix Mali GPU clock
arm64: dts: mediatek: mt8195-demo: fix the memory size of node secmon
soc: mediatek: pm-domains: Fix the power glitch issue
The actual clock feeding into the Mali GPU on the MT8183 is from the
clock gate in the MFGCFG block, not CLK_TOP_MFGPLL_CK from the TOPCKGEN
block, which itself is simply a pass-through placeholder for the MFGPLL
in the APMIXEDSYS block.
Fix the hardware description with the correct clock reference.
Fixes: a8168cebf1 ("arm64: dts: mt8183: Add node for the Mali GPU")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220927101128.44758-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The size of device tree node secmon (bl31_secmon_reserved) was
incorrect. It should be increased to 2MiB (0x200000).
The origin setting will cause some abnormal behavior due to
trusted-firmware-a and related firmware didn't load correctly.
The incorrect behavior may vary because of different software stacks.
For example, it will cause build error in some Yocto project because
it will check if there was enough memory to load trusted-firmware-a
to the reserved memory.
When mt8195-demo.dts sent to the upstream, at that time the size of
BL31 was small. Because supported functions and modules in BL31 are
basic sets when the board was under early development stage.
Now BL31 includes more firmwares of coprocessors and maturer functions
so the size has grown bigger in real applications. According to the value
reported by customers, we think reserved 2MiB for BL31 might be enough
for maybe the following 2 or 3 years.
Cc: stable@vger.kernel.org # v5.19
Fixes: 6147314aee ("arm64: dts: mediatek: Add device-tree for MT8195 Demo board")
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Miles Chen <miles.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221111095540.28881-1-macpaul.lin@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Core
----
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations.
- Add inet drop monitor support.
- A few GRO performance improvements.
- Add infrastructure for atomic dev stats, addressing long standing
data races.
- De-duplicate common code between OVS and conntrack offloading
infrastructure.
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements.
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up
the workload with the number of available CPUs.
- Add the helper support for connection-tracking OVS offload.
BPF
---
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF.
- Make cgroup local storage available to non-cgroup attached BPF
programs.
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers.
- A relevant bunch of BPF verifier fixes and improvements.
- Veristat tool improvements to support custom filtering, sorting,
and replay of results.
- Add LLVM disassembler as default library for dumping JITed code.
- Lots of new BPF documentation for various BPF maps.
- Add bpf_rcu_read_{,un}lock() support for sleepable programs.
- Add RCU grace period chaining to BPF to wait for the completion
of access from both sleepable and non-sleepable BPF programs.
- Add support storing struct task_struct objects as kptrs in maps.
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values.
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions.
Protocols
---------
- TCP: implement Protective Load Balancing across switch links.
- TCP: allow dynamically disabling TCP-MD5 static key, reverting
back to fast[er]-path.
- UDP: Introduce optional per-netns hash lookup table.
- IPv6: simplify and cleanup sockets disposal.
- Netlink: support different type policies for each generic
netlink operation.
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support.
- MPTCP: add netlink notification support for listener sockets
events.
- SCTP: add VRF support, allowing sctp sockets binding to VRF
devices.
- Add bridging MAC Authentication Bypass (MAB) support.
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios.
- More work for Wi-Fi 7 support, comprising conversion of all
the existing drivers to internal TX queue usage.
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading.
- IPSec: extended ack support for more descriptive XFRM error
reporting.
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking.
- IEEE 802154: synchronous send frame and extended filtering
support, initial support for scanning available 15.4 networks.
- Tun: bump the link speed from 10Mbps to 10Gbps.
- Tun/VirtioNet: implement UDP segmentation offload support.
Driver API
----------
- PHY/SFP: improve power level switching between standard
level 1 and the higher power levels.
- New API for netdev <-> devlink_port linkage.
- PTP: convert existing drivers to new frequency adjustment
implementation.
- DSA: add support for rx offloading.
- Autoload DSA tagging driver when dynamically changing protocol.
- Add new PCP and APPTRUST attributes to Data Center Bridging.
- Add configuration support for 800Gbps link speed.
- Add devlink port function attribute to enable/disable RoCE and
migratable.
- Extend devlink-rate to support strict prioriry and weighted fair
queuing.
- Add devlink support to directly reading from region memory.
- New device tree helper to fetch MAC address from nvmem.
- New big TCP helper to simplify temporary header stripping.
New hardware / drivers
----------------------
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches.
- Marvel Prestera AC5X Ethernet Switch.
- WangXun 10 Gigabit NIC.
- Motorcomm yt8521 Gigabit Ethernet.
- Microchip ksz9563 Gigabit Ethernet Switch.
- Microsoft Azure Network Adapter.
- Linux Automation 10Base-T1L adapter.
- PHY:
- Aquantia AQR112 and AQR412.
- Motorcomm YT8531S.
- PTP:
- Orolia ART-CARD.
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices.
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices.
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets.
- Realtek RTL8852BE and RTL8723DS.
- Cypress.CYW4373A0 WiFi + Bluetooth combo device.
Drivers
-------
- CAN:
- gs_usb: bus error reporting support.
- kvaser_usb: listen only and bus error reporting support.
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping.
- implement devlink-rate support.
- support direct read from memory.
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate.
- Support for enhanced events compression.
- extend H/W offload packet manipulation capabilities.
- implement IPSec packet offload mode.
- nVidia/Mellanox (mlx4):
- better big TCP support.
- Netronome Ethernet NICs (nfp):
- IPsec offload support.
- add support for multicast filter.
- Broadcom:
- RSS and PTP support improvements.
- AMD/SolarFlare:
- netlink extened ack improvements.
- add basic flower matches to offload, and related stats.
- Virtual NICs:
- ibmvnic: introduce affinity hint support.
- small / embedded:
- FreeScale fec: add initial XDP support.
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood.
- TI am65-cpsw: add suspend/resume support.
- Mediatek MT7986: add RX wireless wthernet dispatch support.
- Realtek 8169: enable GRO software interrupt coalescing per
default.
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP.
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support.
- add ip6gre support.
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support.
- enable flow offload support.
- Renesas:
- add rswitch R-Car Gen4 gPTP support.
- Microchip (lan966x):
- add full XDP support.
- add TC H/W offload via VCAP.
- enable PTP on bridge interfaces.
- Microchip (ksz8):
- add MTU support for KSZ8 series.
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan.
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support.
- add ack signal support.
- enable coredump support.
- remain_on_channel support.
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities.
- 320 MHz channels support.
- RealTek WiFi (rtw89):
- new dynamic header firmware format support.
- wake-over-WLAN support.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=CbJC
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations
- Add inet drop monitor support
- A few GRO performance improvements
- Add infrastructure for atomic dev stats, addressing long standing
data races
- De-duplicate common code between OVS and conntrack offloading
infrastructure
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up the
workload with the number of available CPUs
- Add the helper support for connection-tracking OVS offload
BPF:
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF
- Make cgroup local storage available to non-cgroup attached BPF
programs
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers
- A relevant bunch of BPF verifier fixes and improvements
- Veristat tool improvements to support custom filtering, sorting,
and replay of results
- Add LLVM disassembler as default library for dumping JITed code
- Lots of new BPF documentation for various BPF maps
- Add bpf_rcu_read_{,un}lock() support for sleepable programs
- Add RCU grace period chaining to BPF to wait for the completion of
access from both sleepable and non-sleepable BPF programs
- Add support storing struct task_struct objects as kptrs in maps
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions
Protocols:
- TCP: implement Protective Load Balancing across switch links
- TCP: allow dynamically disabling TCP-MD5 static key, reverting back
to fast[er]-path
- UDP: Introduce optional per-netns hash lookup table
- IPv6: simplify and cleanup sockets disposal
- Netlink: support different type policies for each generic netlink
operation
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support
- MPTCP: add netlink notification support for listener sockets events
- SCTP: add VRF support, allowing sctp sockets binding to VRF devices
- Add bridging MAC Authentication Bypass (MAB) support
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios
- More work for Wi-Fi 7 support, comprising conversion of all the
existing drivers to internal TX queue usage
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading
- IPSec: extended ack support for more descriptive XFRM error
reporting
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking
- IEEE 802154: synchronous send frame and extended filtering support,
initial support for scanning available 15.4 networks
- Tun: bump the link speed from 10Mbps to 10Gbps
- Tun/VirtioNet: implement UDP segmentation offload support
Driver API:
- PHY/SFP: improve power level switching between standard level 1 and
the higher power levels
- New API for netdev <-> devlink_port linkage
- PTP: convert existing drivers to new frequency adjustment
implementation
- DSA: add support for rx offloading
- Autoload DSA tagging driver when dynamically changing protocol
- Add new PCP and APPTRUST attributes to Data Center Bridging
- Add configuration support for 800Gbps link speed
- Add devlink port function attribute to enable/disable RoCE and
migratable
- Extend devlink-rate to support strict prioriry and weighted fair
queuing
- Add devlink support to directly reading from region memory
- New device tree helper to fetch MAC address from nvmem
- New big TCP helper to simplify temporary header stripping
New hardware / drivers:
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches
- Marvel Prestera AC5X Ethernet Switch
- WangXun 10 Gigabit NIC
- Motorcomm yt8521 Gigabit Ethernet
- Microchip ksz9563 Gigabit Ethernet Switch
- Microsoft Azure Network Adapter
- Linux Automation 10Base-T1L adapter
- PHY:
- Aquantia AQR112 and AQR412
- Motorcomm YT8531S
- PTP:
- Orolia ART-CARD
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets
- Realtek RTL8852BE and RTL8723DS
- Cypress.CYW4373A0 WiFi + Bluetooth combo device
Drivers:
- CAN:
- gs_usb: bus error reporting support
- kvaser_usb: listen only and bus error reporting support
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping
- implement devlink-rate support
- support direct read from memory
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate
- Support for enhanced events compression
- extend H/W offload packet manipulation capabilities
- implement IPSec packet offload mode
- nVidia/Mellanox (mlx4):
- better big TCP support
- Netronome Ethernet NICs (nfp):
- IPsec offload support
- add support for multicast filter
- Broadcom:
- RSS and PTP support improvements
- AMD/SolarFlare:
- netlink extened ack improvements
- add basic flower matches to offload, and related stats
- Virtual NICs:
- ibmvnic: introduce affinity hint support
- small / embedded:
- FreeScale fec: add initial XDP support
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood
- TI am65-cpsw: add suspend/resume support
- Mediatek MT7986: add RX wireless wthernet dispatch support
- Realtek 8169: enable GRO software interrupt coalescing per
default
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support
- add ip6gre support
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support
- enable flow offload support
- Renesas:
- add rswitch R-Car Gen4 gPTP support
- Microchip (lan966x):
- add full XDP support
- add TC H/W offload via VCAP
- enable PTP on bridge interfaces
- Microchip (ksz8):
- add MTU support for KSZ8 series
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support
- add ack signal support
- enable coredump support
- remain_on_channel support
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
- 320 MHz channels support
- RealTek WiFi (rtw89):
- new dynamic header firmware format support
- wake-over-WLAN support"
* tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2002 commits)
ipvs: fix type warning in do_div() on 32 bit
net: lan966x: Remove a useless test in lan966x_ptp_add_trap()
net: ipa: add IPA v4.7 support
dt-bindings: net: qcom,ipa: Add SM6350 compatible
bnxt: Use generic HBH removal helper in tx path
IPv6/GRO: generic helper to remove temporary HBH/jumbo header in driver
selftests: forwarding: Add bridge MDB test
selftests: forwarding: Rename bridge_mdb test
bridge: mcast: Support replacement of MDB port group entries
bridge: mcast: Allow user space to specify MDB entry routing protocol
bridge: mcast: Allow user space to add (*, G) with a source list and filter mode
bridge: mcast: Add support for (*, G) with a source list and filter mode
bridge: mcast: Avoid arming group timer when (S, G) corresponds to a source
bridge: mcast: Add a flag for user installed source entries
bridge: mcast: Expose __br_multicast_del_group_src()
bridge: mcast: Expose br_multicast_new_group_src()
bridge: mcast: Add a centralized error path
bridge: mcast: Place netlink policy before validation functions
bridge: mcast: Split (*, G) and (S, G) addition into different functions
bridge: mcast: Do not derive entry type from its filter mode
...
This patch adds spi support for MT7986.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221118190126.100895-7-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Move the wed_pcie node to have node aligned by address.
Fixes: 00b9903996 ("arm64: dts: mediatek: mt7986: add support for Wireless Ethernet Dispatch")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221118190126.100895-2-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a basic support for the Sony Xperia M5 (codename "Holly")
smartphone, powered by a MediaTek Helio X10 SoC.
This achieves a console boot.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221027095504.37432-7-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the mmc nodes to support all of the four controllers, used for
eMMC, SD/MicroSD and SDIO storage.
All of these controller nodes are left disabled by default, as
usage is board dependent.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221027095504.37432-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This SoC has a DMA controller with tx/rx channels for all of the
UART controller IPs: add the apdma node and wire up the DMAs on
all controllers.
When one of the UART controllers is used as a serial console,
the DMA will be automatically ignored.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221027095504.37432-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The UART nodes had a dummy clock for early bringup, as it is
expected that these are left on by the bootloader: now that
the pericfg clock controller is supported, we can replace
them with the real clocks.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221027095504.37432-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add nodes for topckgen, infracfg and pericfg, providing various
clocks and resets and needed to support basic IPs of this SoC.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221027095504.37432-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In cherry projects, we use edptx as the internal display interface
and use dptx as the external display interface. To support this, we
need to add more properties.
- Add pinctrls for edptx and dptx.
- Add ports for edptx and dptx.
The port connections for the internal and external display:
dp-intf0 -> edptx -> panel
dp-intf1 -> dptx
The edptx endpoint is kept empty for now, as the panel addition will
come in a later commit.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221110063716.25677-5-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Dp-intfs provide the pixel data to edptx and dptx. To support edptx
and dptx, we need to add dp-intf0 and dp-intf1 ports.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221110063716.25677-4-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In MT8195, we use edptx as the internal display interface and use
dptx as the external display interface. Therefore, we need to add
these nodes to support the internal display and the external display.
- Add dp calibration data in the efuse node.
- Add edptx and dptx nodes for MT8195.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221110063716.25677-3-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Dp-intfs provide the pixel data to edptx and dptx. To support edptx
and dptx, we need to add dp-intf0 and dp-intf1 nodes.
Dp-intf0 is for edptx and dp-intf1 is for dptx.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221110063716.25677-2-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Update its unit name to oscillator-26m and remove the unneeded unit
address to fix a unit_address_vs_reg warning.
Fixes: 464c510f60 ("arm64: dts: mediatek: add mt6797 support")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-9-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Update the names to regulator-usb-p{0-3}-vbus to fix unit_address_vs_reg
warnings for those.
Fixes: 1724f4cc51 ("arm64: dts: Add USB3 related nodes for MT2712")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-7-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Update the names to regulator-vproc-buck{0,1} to fix unit_addres_vs_reg
warnings for those.
Fixes: f75dd8bdd3 ("arm64: dts: mediatek: add mt2712 cpufreq related device nodes")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The unit address for the pinctrl node is (0x)1000b000 and not
(0x)10005000, which is the syscfg_pctl_a address instead.
This fixes the following warning:
arch/arm64/boot/dts/mediatek/mt2712e.dtsi:264.40-267.4: Warning
(unique_unit_address): /syscfg_pctl_a@10005000: duplicate
unit-address (also used in node /pinctrl@10005000)
Fixes: f0c64340b7 ("arm64: dts: mt2712: add pintcrl device node.")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Rename the fixed-clock oscillators to remove the unit address.
This solves unit_address_vs_reg warnings.
Fixes: 5d4839709c ("arm64: dts: mt2712: Add clock controller device nodes")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Rename fixed-clock oscillators to oscillator-26m and oscillator-32k
and remove the unit address to fix the unit_address_vs_reg warning;
fix the unit address for interrupt and intpol controllers by
removing a leading zero in their unit address.
This commit fixes the following warnings:
(unit_address_vs_reg): /oscillator@0: node has a unit name, but
no reg or ranges property
(unit_address_vs_reg): /oscillator@1: node has a unit name, but
no reg or ranges property
(simple_bus_reg): /soc/interrupt-controller@0c000000: simple-bus
unit address format error, expected "c000000"
(simple_bus_reg): /soc/intpol-controller@0c53a650: simple-bus
unit address format error, expected "c53a650"
Fixes: 4c7a626077 ("arm64: dts: add dts nodes for MT6779")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Rename the oscillator fixed-clock to oscillator-40m and remove
the unit address to fix warnings.
arch/arm64/boot/dts/mediatek/mt7986a.dtsi:17.23-22.4: Warning
(unit_address_vs_reg): /oscillator@0: node has a unit name,
but no reg or ranges property
Fixes: 1f9986b258 ("arm64: dts: mediatek: add clock support for mt7986a")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The capacity-dmips-mhz parameter was miscalculated: this SoC runs
the first (Cortex-A55) cluster at a maximum of 2000MHz and the
second (Cortex-A78) cluster at a maximum of 3000MHz.
In order to calculate the right capacity-dmips-mhz, the following
test was performed:
1. CPUFREQ governor was set to 'performance' on both clusters
2. Ran dhrystone with 500000000 iterations for 10 times on each cluster
3. Calculate the mean result for each cluster
4. Calculate DMIPS/MHz: dmips_mhz = dmips_per_second / cpu_mhz
5. Scale results to 1024:
result_c0 = (dmips_mhz_c0 - min_dmips_mhz(c0, c1)) /
(max_dmips_mhz(c0, c1) - min_dmips_mhz(c0, c1)) * 1024
The mean results for this SoC are:
Cluster 0 (LITTLE): 11990400 Dhry/s
Cluster 1 (BIG): 59809036 Dhry/s
The calculated scaled results are:
Cluster 0: 307,934312801831 (rounded to 308)
Cluster 1: 1024
Fixes: 37f2582883 ("arm64: dts: Add mediatek SoC mt8195 and evaluation board")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221005093404.33102-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This arrange device tree nodes in alphabetical order.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221106085034.12582-2-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Similar to TX Wireless Ethernet Dispatch, introduce RX Wireless Ethernet
Dispatch to offload traffic received by the wlan interface to lan/wan
one.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Binding requires node name to be rng not trng:
trng@1020f000: $nodename:0: 'trng@1020f000' does not match '^rng@[0-9a-f]+$'
Fixes: 50137c150f ("arm64: dts: mediatek: add basic mt7986 support")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221027151022.5541-1-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This property is not defined in binding and driver.
Fixes: 2c002a3049 ("arm64: dts: mt7622: add mmc related device nodes")
Fixes: 0b6286dd96 ("arm64: dts: mt7622: add bananapi BPI-R64 board")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221025132953.81286-6-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This property is not defined in binding and driver.
Fixes: cd894e274b ("arm64: dts: mt8183: Add krane-sku176 board")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221025132953.81286-5-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
First 3 clocks for mt2712 need to be "source", "hclk", "source_cg"
so swap last 2 of mmc0 to match the binding.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221025132953.81286-4-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Remove syscon compatible string from pin controller to follow
DT bindings and pass checks. Adding the syscon compatible to
the DT bindings documentation instead causes a different check
error due to the syscon document specifying a maximum of 1 item
in the reg property, while this has 9. This pin controller has
never been, and will never be, used as a syscon, hence it is
safe to drop this compatible.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221028153505.23741-2-y.oudjana@protonmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The i2sN-share properties were never documented in the dt-binding and
thus shouldn't be used. Now that the ASoC machine drivers are setting
the I2S clock sharing internally, these properties are no longer needed,
so remove them.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220908161154.648557-8-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The DeviceTree Specification v0.3 specifies that the cache node
'compatible' and 'cache-level' properties are 'required'. Cf.
s3.8 Multi-level and Shared Cache Nodes
The 'cache-unified' property should be present if one of the
properties for unified cache is present ('cache-size', ...).
Update the Device Trees accordingly.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Link: https://lore.kernel.org/r/20221107155825.1644604-13-pierre.gondois@arm.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Most of the changes fall into one of three categories: adding support
for additional devices on existing machines, cleaning up issues found
by the ongoing conversion to machine-readable bindings, and addressing
minor mistakes in the existing DT data.
Across SoC vendors, Qualcomm and Freescale stick out as getting the most
updates, which corresponds to their dominance in the mobile phone and
embedded industrial markets, respectively.
There are 636 non-merge changeset in this branch, which is a little
lower than most times, but more importantly we only add 36 machine
files, which is about half of what we had the past few releases.
Eight new SoCs are added, but all of them are variations of already
supported SoC families, and most of them come with one reference board
design from the SoC vendor:
- Mediatek MT8186 is a Chromebook/Tablet type SoC, similar to the
MT65xx series of phone SoCs, with two Cortex-A76 and six Cortex-A55
cores.
- TI AM62A is another member of the K3 family with Cortex-A53 cores,
this one is targetted at Video/Vision processing for industrial
and automotive applications.
- NXP i.MX8DXL is another chip for this market in the ever-growing
i.MX8 family, this one again with two Cortex-A35 cores.
- Renesas R-Car H3Ne-1.7G (R8A779MB) and R-Car V3H2 (R8A77980A) are
minor updates of R8A77951 and R8A77980, respectively.
- Qualcomm IPQ8064-v2.0, IPQ8062 and IPQ8065 are all variants of the
IPQ8064 chip, with minimally different features.
The AMD Pensando Elba and Apple M1 Ultra SoC support was getting close
this time, but in the end did not make the cut.
The new machines based on existing SoC support are fairly uneventful:
- Sony Xperia 1 IV is a fairly recent phone based on Qualcomm
Snapdragon 8 Gen 1.
- Three Samsung phones based on Snapdragon 410: Galaxy E5, E7 and
Grand Max. These are added for both 32-bit and 64-bit kernels,
as they originally shipped running 32-bit code.
- Two new servers using AST2600 BMCs: AMD DaytonaX and Ampere
Mt. Mitchell
- Three new machines based on Rockchips RK3399 and RK3566:
Anberic RG353P and RG503, Pine64 Pinephone Pro, Open AI Lab
- Multiple NXP i.MX6/i.MX8 based boards: Kontron SL/BL i.MX8MM OSM-S,
i.MX8MM Gateworks GW7904, MSC SM2S-IMX8PLUS SoM and carrier board
- Two development boards in the Microchip AT91 family:
SAMA5D3-EDS and lan966x-pcb8290.
- Minor variants of existing boards using Amlogic, Broadcom, Marvell,
Rockchips, Freescale Layerscape and Socionext Uniphier SoCs.
-----BEGIN PGP SIGNATURE-----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=xPfV
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"Most of the changes fall into one of three categories: adding support
for additional devices on existing machines, cleaning up issues found
by the ongoing conversion to machine-readable bindings, and addressing
minor mistakes in the existing DT data.
Across SoC vendors, Qualcomm and Freescale stick out as getting the
most updates, which corresponds to their dominance in the mobile phone
and embedded industrial markets, respectively.
There are 636 non-merge changeset in this branch, which is a little
lower than most times, but more importantly we only add 36 machine
files, which is about half of what we had the past few releases.
Eight new SoCs are added, but all of them are variations of already
supported SoC families, and most of them come with one reference board
design from the SoC vendor:
- Mediatek MT8186 is a Chromebook/Tablet type SoC, similar to the
MT65xx series of phone SoCs, with two Cortex-A76 and six Cortex-A55
cores.
- TI AM62A is another member of the K3 family with Cortex-A53 cores,
this one is targetted at Video/Vision processing for industrial and
automotive applications.
- NXP i.MX8DXL is another chip for this market in the ever-growing
i.MX8 family, this one again with two Cortex-A35 cores.
- Renesas R-Car H3Ne-1.7G (R8A779MB) and R-Car V3H2 (R8A77980A) are
minor updates of R8A77951 and R8A77980, respectively.
- Qualcomm IPQ8064-v2.0, IPQ8062 and IPQ8065 are all variants of the
IPQ8064 chip, with minimally different features.
The AMD Pensando Elba and Apple M1 Ultra SoC support was getting close
this time, but in the end did not make the cut.
The new machines based on existing SoC support are fairly uneventful:
- Sony Xperia 1 IV is a fairly recent phone based on Qualcomm
Snapdragon 8 Gen 1.
- Three Samsung phones based on Snapdragon 410: Galaxy E5, E7 and
Grand Max. These are added for both 32-bit and 64-bit kernels, as
they originally shipped running 32-bit code.
- Two new servers using AST2600 BMCs: AMD DaytonaX and Ampere Mt.
Mitchell
- Three new machines based on Rockchips RK3399 and RK3566: Anberic
RG353P and RG503, Pine64 Pinephone Pro, Open AI Lab
- Multiple NXP i.MX6/i.MX8 based boards: Kontron SL/BL i.MX8MM OSM-S,
i.MX8MM Gateworks GW7904, MSC SM2S-IMX8PLUS SoM and carrier board
- Two development boards in the Microchip AT91 family: SAMA5D3-EDS
and lan966x-pcb8290.
- Minor variants of existing boards using Amlogic, Broadcom, Marvell,
Rockchips, Freescale Layerscape and Socionext Uniphier SoCs"
* tag 'arm-dt-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (617 commits)
Revert "ARM: dts: BCM5301X: Add basic PCI controller properties"
ARM: dts: s5pv210: correct double "pins" in pinmux node
ARM: dts: exynos: fix polarity of VBUS GPIO of Origen
arm64: dts: exynos: fix polarity of "enable" line of NFC chip in TM2
arm64: dts: uniphier: Add L2 cache node
arm64: dts: uniphier: Remove compatible "snps,dw-pcie" from pcie node
arm64: dts: uniphier: Fix opp-table node name for LD20
arm64: dts: uniphier: Add USB-device support for PXs3 reference board
arm64: dts: uniphier: Add ahci controller nodes for PXs3
arm64: dts: uniphier: Use GIC interrupt definitions
arm64: dts: uniphier: Rename gpio-hog nodes
arm64: dts: uniphier: Rename usb-glue node for USB3 to usb-controller
arm64: dts: uniphier: Rename usb-phy node for USB2 to usb-controller
arm64: dts: uniphier: Rename pvtctl node to thermal-sensor
ARM: dts: uniphier: Remove compatible "snps,dw-pcie-ep" from pcie-ep node
ARM: dts: uniphier: Move interrupt-parent property to each child node in uniphier-support-card
ARM: dts: uniphier: Add ahci controller nodes for PXs2
ARM: dts: uniphier: Add ahci controller nodes for Pro4
ARM: dts: uniphier: Use GIC interrupt definitions
ARM: dts: uniphier: Rename gpio-hog node
...
Update the name of property 'clk_csr' as 'snps,clk-csr' to align with
the property name in the binding file.
Signed-off-by: Jianguo Zhang <jianguo.zhang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce wed0 and wed1 nodes in order to enable offloading forwarding
between ethernet and wireless devices on the mt7986 chipset.
Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add a node for mt6795-systimer: this is necessary to start the
System Timer(s) for all cores, finally making CNTVCT_EL0 usable.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220729093536.27623-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
All machines in the Cherry platform use MT6315 over SPMI: add the
two instances, providing Vbcpu and Vgpu regulators.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220902081156.38526-8-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The Cherry platform uses an Elantech touchpad/trackpad: enable
probing it at address 0x15 on I2C1.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220902081156.38526-7-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
As of now, all of the boards based on the cherry platform have a
usable secondary SD/MMC controller, usually for SD cards: enable
it to allow both booting from it and generally accessing external
storage.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220902081156.38526-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Chromebooks' embedded keyboards differ from standard layouts for the
top row, as this one doesn't have the standard function keys but
shortcuts instead: map these keys to achieve the functionality that
is pictured on the printouts.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220902081156.38526-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add support for the Cr50 Google Security Chip (GSC) found on this
platform on I2C3 to support TPM and to also use it as an entropy
source for the kernel.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220902081156.38526-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Wire up the ChromeOS Embedded Controller on SPI0 and its communication
channel via SCP RPMSG along with all of the offered functionality,
including Keyboard, Smart Battery Metrics (SBS), keyboard backlight,
I2C tunnel, regulators and Type-C connector management.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220902081156.38526-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT8195 features a SCP like some other older SoCs, and Cherry uses it
for various tasks. Add the required pin configuration and DMA pool
and enable the node.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220902081156.38526-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Correct the phandle of power domain node referenced by vcodec nodes.
arch/arm64/boot/dts/mediatek/mt8173.dtsi:1450.35-1471.5: Warning (power_domains_property): /soc/vcodec@18002000: Missing property '#power-domain-cells' in node /soc/syscon@10006000 or bad phandle (referred from power-domains[0])
arch/arm64/boot/dts/mediatek/mt8173.dtsi:1502.35-1522.5: Warning (power_domains_property): /soc/vcodec@19002000: Missing property '#power-domain-cells' in node /soc/syscon@10006000 or bad phandle (referred from power-domains[0])
Fixes: d3dfd46885 ("arm64: dts: mediatek: Update mt81xx scpsys node to align with dt-bindings")
Signed-off-by: Tinghan Shen <tinghan.shen@mediatek.com>
Link: https://lore.kernel.org/r/20220831065100.27722-1-tinghan.shen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The MediaTek xHCI dt-binding expects a specific order for the clocks,
but the mt8192 and mt8195 devicetrees were skipping some of the middle
clocks. These clocks are wired to the controller hardware but aren't
controllable.
Add the missing clocks as handles to fixed clocks, so that the clock
order is respected and the dtbs_check warnings are gone.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220708194314.56922-1-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add dsi node for mt8192 SoC.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220712114046.15574-6-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add display nodes and gce info for mt8192 SoC.
GCE (Global Command Engine) properties to the display nodes in order to
enable the usage of the CMDQ (Command Queue), which is required for
operating the display.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220712114046.15574-5-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
To support reset of mmsys, we include mt8192-resets.h and add
property of #reset-cells in mmsys.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220712114046.15574-4-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add mipi_tx node for mt8192 SoC.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220712114046.15574-3-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add pwm node for mt8192 SoC.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220712114046.15574-2-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT8186 is a SoC based on 64bit ARMv8 architecture. It contains 6 CA55
and 2 CA76 cores. MT8186 share many HW IP with MT65xx series.
We add basic chip support for MediaTek MT8186 on evaluation board.
Signed-off-by: Allen-KH Cheng <Allen-KH.Cheng@mediatek.com>
Link: https://lore.kernel.org/r/20220825170448.17024-1-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The I2C0 node should not be enabled globally, as usage is board
dependent; disable it in dtsi.
Signed-off-by: Tzung-Bi Shih <tzungbi@chromium.org>
Signed-off-by: Tinghan Shen <tinghan.shen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220811025813.21492-10-tinghan.shen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Disable the external output reset signal of watchdog reset to avoid losing
the reset reason stored in the watchdog registers.
Signed-off-by: Fengquan Chen <fengquan.chen@mediatek.com>
Signed-off-by: Tinghan Shen <tinghan.shen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220811025813.21492-9-tinghan.shen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Update scpsys nodes using simple-mfd in mt81xx SoC devicetree
to align with the bindings.
Add specific compatibles for syscon node, even it's a dummy compatible,
because syscon node must come with a specific compatible.
Remove the '#power-domain-cells" propertry since the simple-mfd node is
not the power domain provider; the provider is the child node.
Signed-off-by: Tinghan Shen <tinghan.shen@mediatek.com>
Link: https://lore.kernel.org/r/20220811025813.21492-8-tinghan.shen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT8183 has an on-SoC keyboard controller commonly used for volume
up/down buttons.
List it in the SoC dts so that boards can enable/use it.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220720-mt8183-keypad-v2-6-6d42c357cb76@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add device nodes for Media Data Path 3 (MDP3) modules.
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220823023803.27850-4-moudy.ho@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text. Also included in here are a few other minor updates,
2 USB files, and one Documentation file update to get the SPDX lines
correct.
All of these have been in the linux-next tree for a very long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYupz3g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynPUgCgslaf2ssCgW5IeuXbhla+ZBRAzisAnjVgOvLN
4AKdqbiBNlFbCroQwmeQ
=v1sg
-----END PGP SIGNATURE-----
Merge tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
The bananapi R64 (BPI-R64) experiences wrong WPS button signals.
In OpenWrt pushing the WPS button while powering on the device will set
it to recovery mode. Currently, this also happens without any user
interaction. In particular, the wrong signals appear while booting the
device or restarting it, e.g. after doing a system upgrade. If the
device is in recovery mode the user needs to manually power cycle or
restart it.
The official BPI-R64 sources set the WPS button to GPIO_ACTIVE_LOW in
the device tree. This setting seems to suppress the unwanted WPS button
press signals. So this commit changes the button from GPIO_ACTIVE_HIGH to
GPIO_ACTIVE_LOW.
The official BPI-R64 sources can be found on
https://github.com/BPI-SINOVOIP/BPI-R64-openwrt
Fixes: 0b6286dd96 ("arm64: dts: mt7622: add bananapi BPI-R64 board")
Suggested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Link: https://lore.kernel.org/r/20220630111746.4098-1-vincent@systemli.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add axi clock since the driver change to DMA mode which need
to enable axi clock. And change spi clock to 26MHz as default.
Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Link: https://lore.kernel.org/r/20220630090157.29486-2-xiangsheng.hou@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This platform carries a HID compatible I2C touchscreen on the i2c4 bus,
but it may be at a different address, depending on the board model.
Add the node for a touchscreen at 0x10, but enable it only in the
final board dts.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-12-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This platform has a SPI NOR: enable support for it, completing the
storage compartment enablement for the entire platform.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-11-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
All devices of the Cherry platform have a MT6360 sub-pmic,
providing two LDOs. Add the required node to enable the PMIC
but without regulators yet, as these will be added in a
later commit.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-10-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add USB functionality by enabling the required PHYs and the XHCI
controllers.
This enables all of the supported USB ports on the Cherry boards.
Please note that u3phy1 also enables u3port1, which is configured
to be a PCI-Express PHY for the second PCIe controller that is
found on the MT8195 SoC, which will be enabled in a later commit.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-9-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This platform uses eight I2C controllers and one SPI controller:
in preparation for enabling devices attached to these controllers,
add basic configuration to enable the busses.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-8-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add gpio-line-names to document GPIO names and add the default basic
pin configuration to allow lower power operation by setting appropriate
state on the unused pins.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-7-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add mtk-sd controller and pin configuration to enable the internal
eMMC storage: now it is possible to mount a rootfs located at the
internal storage.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
To allow MT6359 peripherals to trigger interrupts and the driver to
safely handle them, assign the right interrupt line for the Cherry
platform to the MT6359 PMIC node.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the regulators layout for this platform, including the basic power
rails controlled by the EC (and/or always on).
Moreover, include the MT6359 PMIC devicetree and add some configuration
for its regulators, essential to keep the machine alive after booting.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Introduce the MT8195 Cherry Chromebook platform, including three
revisions of Cherry Tomato boards.
This basic configuration allows to boot Linux on all board revisions
and get a serial console from a ramdisk.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add support for the SPI NOR flash memory present on the Asurada
platform.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-20-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable support for the SCP co-processor present on MT8192. It is used
as part of the video encoding and decoding processes.
A region of memory is carved out for its use, and remoteproc setup for
communication with the ChromeOS EC.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-19-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable both MMC controllers present on Asurada. MMC0 is for
non-removable internal memory, while MMC1 is an SD card slot. MMC1 isn't
used on all machines, but in those cases the CD interrupt is never
triggered and thus it is basically as if it was disabled.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-18-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The Asurada platform uses regulators from MT6315 PMICs acessible through
SPMI. Add support for them.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-17-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT6359 is the primary PMIC present on the Asurada platform. Include its
dtsi and configure properties specific for the platform.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-16-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable MT8192's PCIe controller and add support for the MT7921e WiFi
card that is present on that bus for the Asurada platform.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-15-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable XHCI controller on the Asurada platform. This allows the use of
the USB ports, and therefore a rootfs can be loaded and a usable shell
reached from a live USB image.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-14-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The Spherion board has keyboard backlight controlled by the PWM signal
generated by the ChromeOS EC.
Enable PWM output for ChromeOS EC and add a PWM controlled LED node for
the keyboard backlight.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-13-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
All machines of the Asurada platform have a touchscreen at address 0x10
in the I2C0 bus, but the devices vary: Spherion has the Elan eKTH3500
touchscreen, while Hayato has a generic HID-over-i2c touchscreen.
Add common support for the touchscreens on the platform and the
specifics in each board file.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-12-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add support for the Elan eKTH3000 i2c trackpad present on Asurada. It is
connected to the I2C2 bus and has address 0x15.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-11-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The Asurada platform has a Google Security Chip connected to the SPI5
bus. It runs the cr50 firmware and provides TPM functionality. Add
support for it.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-10-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Chromebooks' embedded keyboards differ from standard layouts for the
top row in that they have shortcuts in place of the standard function
keys. Map these keys to achieve the functionality that is pictured on
the printouts.
There's a minor difference between the keys present on Hayato, which
uses an older layout, and Spherion, which uses a newer one.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-9-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add support for the ChromeOS Embedded Controller present on the Asurada
platform. It is connected through the SPI1 bus and offers several
functionalities: base detection, PWM controller, I2C tunneling,
regulators, Type-C connector management, keyboard and Smart Battery
Metrics (SBS).
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-8-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The Asurada platform has five I2C controllers and two SPI controllers
that are used. In preparation for enabling the devices connected to
these controllers, enable and configure their busses.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-7-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add system-wide power supplies present on all of the boards in the
Asurada family.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-6-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the gpio-line-names property to gpio-controller in order to
document the usage of GPIOs on the Asurada platform.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-5-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Introduce the MT8192 Asurada Chromebook platform, including the Asurada
Spherion and Asurada Hayato boards.
This is enough configuration to get serial output working on Spherion
and Hayato.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220629155956.1138955-4-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a phandle to the MT8183_POWER_DOMAIN_MFG_ASYNC power domain and
assign the GPU VSRAM supply to this in mt8183-kukui: this allows to
keep the sram powered up while the GPU is used.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220623123850.110225-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a node for the pinctrl controller found on MT6795 but without
configuration for any pin, as that's expected to be done in the
machine-specific devicetrees.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-10-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Remove the RTC and UART fixed clocks, as these were introduced to
temporarily provide a dummy clock to devices: since the two 26M/32K
fixed oscillators clocks (which do really exist in the SoC) have
been added, there's no reason to keep the aforementioned (and now
redundant) dummies in this devicetree.
In order to remove the uart dummy clock, it was necessary to also
reassign the clock of all UART nodes to clk26m.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-7-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the 32kHz and 26MHz oscillators as fixed clocks in devicetree to
provide a good initial clock spec, since this SoC features two always
on oscillators running at the aforementioned frequencies.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
At least on commercial devices like some smartphones, the bootloader
will initialize the SoC watchdog and set it to reboot the board when
it times out. The last pet that this watchdog is getting is right
before booting the kernel and left it enabled as a protection against
boot failure: this means that Linux is expected to initialize this
device and pet as soon as possible, or it will bark and reset the AP.
In order to prevent that, add the required watchdog node as default
enabled: this will have no side effects on boards that are not
performing the aforementioned watchdog setup before booting Linux.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This SoC is HMP and has two clusters with four Cortex-A53 cores each:
declare a cpu map and, while at it, also add the next-level-cache
properties.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MMIO devices should be inside of a soc bus node, as it's done for the
vast majority of ARM64 devicetrees, and for almost all MTK devicetrees.
Create a simple-bus soc node and move all devices with a MMIO address
space in there.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The IOMMU driver now looks for the "mediatek,infracfg" phandle as a
new way to retrieve a syscon to that:
even though the old way is retained, it has been deprecated and the
driver will write a message in kmsg advertising to use the phandle
way instead.
For this reason, assign the right phandle to mediatek,infracfg in
the iommu node.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Miles Chen <miles.chen@mediatek.com>
Link: https://lore.kernel.org/r/20220616110830.26037-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The IOMMU driver now looks for the "mediatek,infracfg" phandle as a
new way to retrieve a syscon to that:
even though the old way is retained, it has been deprecated and the
driver will write a message in kmsg advertising to use the phandle
way instead.
For this reason, assign the right phandle to mediatek,infracfg in
the iommu node.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Miles Chen <miles.chen@mediatek.com>
Link: https://lore.kernel.org/r/20220616110830.26037-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Need also provide a specific compatible "mediatek,mt8192-efuse" at
the same time when use the generic compatible "mediatek,efuse".
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220617093132.22578-3-chunfeng.yun@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The entry-method property of the idle-states node should be "psci" as
described in the idle-states binding, since this is already the value of
enable-method in the CPU nodes. Fix it to get rid of a dtbs_check
warning.
Fixes: 9260918d3a ("arm64: dts: mt8192: Add cpu-idle-states")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220617233150.2466344-3-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Tweak the name of the idle-states subnodes so that they follow the
binding pattern, getting rid of dtbs_check warnings.
Only the usage of "-" in the name was necessary, but "off" was also
exchanged for "sleep" since that seems to be a more common wording in
other dts files.
Fixes: 9260918d3a ("arm64: dts: mt8192: Add cpu-idle-states")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220617233150.2466344-2-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
As explained in Documentation/devicetree/bindings/mmc/mmc-controller.yaml,
the 'enable-sdio-wakeup' property is considered deprecated.
Replace it with the 'wakeup-source' property instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20220621124435.121740-1-festevam@gmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
We will use mediatek clock reset as infracfg_ao reset instead of
ti-syscon. To support this, remove property of ti reset and add
property of #reset-cells for mediatek clock reset.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220503093856.22250-17-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
To support reset of infra, we add property of #reset-cells.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220503093856.22250-16-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In order to allow modules with latency requirements such as MDP3
to set registers through CMDQ, add the relevant dts property.
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://lore.kernel.org/r/20220610063424.7800-6-moudy.ho@mediatek.com
[mb: fix commit subject]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The node names should be generic and DT schema expects certain pattern
with 'led'. Use generic color properties instead of the node name.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220616005333.18491-16-krzysztof.kozlowski@linaro.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fix whitespace coding style: use single space instead of tabs or
multiple spaces around '=' sign in property assignment. No functional
changes (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220526204402.832393-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable USB remote wakeup of all four xHCI controller
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220617072344.21461-2-chunfeng.yun@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add efuse node and cells used by t-phy to fix the bit shift issue
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220617072344.21461-1-chunfeng.yun@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add compatible/reg/irq/clock/efuse setting in svs node.
Signed-off-by: Roger Lu <roger.lu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20220516004311.18358-3-roger.lu@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license version 2 as
published by the free software foundation this program is distributed
in the hope that it will be useful merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add mediatek,cci property to support MediaTek CCI feature.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220516111130.13325-4-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
- Add cpufreq opp table.
- Add MediaTek cci opp table.
- Add property of opp table and clock fro cpufreq.
Signed-off-by: Andrew-sh.Cheng <andrew-sh.cheng@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220516111130.13325-2-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
There are 40 branches this time, adding a lot of new hardware
support, and cleanups. Krzysztof Kozlowski continues his treewide
cleanups.
There are a number of new SoCs, all of them as part of existing
families, and typically added along with a reference board:
- Renesas RZ/G2UL (R9A07G043) is the single-core version of the RZ/G2L
general-purpose MPU.
- Renesas RZ/V2M (R9A09G011) is a smart camera SoC
- Renesas R-Car V4H (R8A779G0) is an automotive chip with Cortex-A76
cores and deep learning accerlation.
- Broadcom BCM47622 is a new broadband SoC based on a quad Cortex-A7
and dual Wifi-6.
- Corstone1000 is a generic platform from Arm that is used for designing
custom SoCs, the support for now is for the Fixed Virtual Platform
emulation for it.
- Mediatek MT8195 (Kompanio 1200) is a high-end consumer chip used
in upcoming Chromebooks.
- NXP i.MXRT1050 is a Cortex-M7 based microcontroller, the first
MMU-less SoC to be added in a while
New machines based on already supported SoCs this time are mainly
for 32-bit platforms and include:
- Two wireless routers based on Broadcom bcm4708
- 30 new boards based on NXP i.MX6, i.MX7 and i.MX8 families, mostly
for the industrial embedded market, and on NXP LS1021A based
IOT board.
- Two ethernet switches based on Microchip LAN966
- Eight Qualcomm Snapdragon based machines, including a smartwatch,
a Chromebook board and some phones
- Another phone based on the old ST-Ericsson Ux500 platform
- Seven STM32MP1 based boards
- Four single-board computers based on Rockchip RK3566/RK3568
-----BEGIN PGP SIGNATURE-----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=LsM7
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM DT updates from Arnd Bergmann:
"There are 40 branches this time, adding a lot of new hardware support,
and cleanups. Krzysztof Kozlowski continues his treewide cleanups.
There are a number of new SoCs, all of them as part of existing
families, and typically added along with a reference board:
- Renesas RZ/G2UL (R9A07G043) is the single-core version of the
RZ/G2L general-purpose MPU.
- Renesas RZ/V2M (R9A09G011) is a smart camera SoC
- Renesas R-Car V4H (R8A779G0) is an automotive chip with Cortex-A76
cores and deep learning accerlation.
- Broadcom BCM47622 is a new broadband SoC based on a quad Cortex-A7
and dual Wifi-6.
- Corstone1000 is a generic platform from Arm that is used for
designing custom SoCs, the support for now is for the Fixed Virtual
Platform emulation for it.
- Mediatek MT8195 (Kompanio 1200) is a high-end consumer chip used in
upcoming Chromebooks.
- NXP i.MXRT1050 is a Cortex-M7 based microcontroller, the first
MMU-less SoC to be added in a while
New machines based on already supported SoCs this time are mainly for
32-bit platforms and include:
- Two wireless routers based on Broadcom bcm4708
- 30 new boards based on NXP i.MX6, i.MX7 and i.MX8 families, mostly
for the industrial embedded market, and on NXP LS1021A based IOT
board.
- Two ethernet switches based on Microchip LAN966
- Eight Qualcomm Snapdragon based machines, including a smartwatch, a
Chromebook board and some phones
- Another phone based on the old ST-Ericsson Ux500 platform
- Seven STM32MP1 based boards
- Four single-board computers based on Rockchip RK3566/RK3568"
* tag 'arm-dt-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (791 commits)
ARM: dts: kswitch-d10: enable networking
ARM: dts: lan966x: add switch node
ARM: dts: lan966x: add serdes node
ARM: dts: lan966x: add reset switch reset node
ARM: dts: lan966x: add MIIM nodes
ARM: dts: lan966x: add hwmon node
ARM: dts: lan966x: add basic Kontron KSwitch D10 support
ARM: dts: lan966x: add flexcom I2C nodes
ARM: dts: lan966x: add flexcom SPI nodes
ARM: dts: lan966x: add all flexcom usart nodes
ARM: dts: lan966x: add missing uart DMA channel
ARM: dts: lan966x: add sgpio node
ARM: dts: lan966x: swap dma channels for crypto node
ARM: dts: lan966x: rename pinctrl nodes
ARM: dts: at91: sama7g5: remove interrupt-parent from gic node
ARM: dts: at91: use generic node name for dataflash
ARM: dts: turris-omnia: Add atsha204a node
arm64: dts: mt8192: Follow binding order for SCP registers
arm64: dts: mediatek: add mtk-snfi for mt7622
arm64: dts: mediatek: mt8195-demo: enable uart1
...
Introduce ethernet nodes in mt7986 bindings in order to
enable mt7986a/mt7986b ethernet support.
Co-developed-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dt-binding for SCP documents the reg-names order as sram, cfg,
l1tcm. Update the SCP node on the mt8192 devicetree to follow that
order, which gets rid of a dtbs_check warning. This doesn't change any
behavior since the SCP driver accesses the memory regions through the
names anyway.
Fixes: c63556ec6b ("arm64: dts: mt8192: Add SCP node")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220504214516.2957504-1-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This property doesn't seem to exist in the documentation nor
in source code, let's remove it from the device-tree.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Link: https://lore.kernel.org/r/20220426134106.242353-7-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fix the following dtbs_check error by using the correct node name:
/home/fabo/build/linux/mt8183-pumpkin/arch/arm64/boot/dts/mediatek/mt8183-pumpkin.dtb: ntc: $nodename:0: 'ntc' does not match '^thermistor(.*)?$'
From schema: /home/fabo/devel/baylibre/linux-mainline/Documentation/devicetree/bindings/hwmon/ntc-thermistor.yaml
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20220426164755.435372-1-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
On an MT7622 system, the kernel complains of not being able to detect the cache
hierarchy of CPU 0. Specify the shared L2 cache node in the device tree, in
order to fix this.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Link: https://lore.kernel.org/r/20220428225755.785153-1-rsalvaterra@gmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The MT7622 device tree never bothered to specify the number of virtual DMA
channels for the HSDMA controller, always falling back to the default value of
3. Make this value explicit, in order to avoid the following dmesg notification:
mtk_hsdma 1b007000.dma-controller: Using 3 as missing dma-requests property
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Link: https://lore.kernel.org/r/20220429084225.298213-1-rsalvaterra@gmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This property doesn't seem to exist in the documentation nor
in source code, but for some reason it is defined in a bunch
of device trees.
Signed-off-by: Dang Huynh <danct12@riseup.net>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20220425064850.246228-1-danct12@riseup.net
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add basic device-tree for the MT8195 Demo board. The
Demo board is made by MediaTek and has a MT8195 SoC,
associated with the MT6359 and MT6360 PMICs, and
the MT7921 connectivity chip.
The IOs available on that board are:
* 1 USB Type-C connector with DP aux mode support
* 1 USB Type-A connector
* 1 full size HDMI RX and 1 full size HDMI TX connector
* 1 uSD slot
* 40 pins header
* SPI interface header
* 1 M.2 slot
* 1 audio jack
* 1 micro-USB port for serial debug
* 2 connectors for DSI displays
* 3 connectors for CSI cameras
* 1 connector for a eDP panel
* 1 MMC storage
This commit adds basic support in order to be able to boot.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20220415150003.1793063-3-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In mt8192 SoC, mmc driver dose not use the MSDC module to control
clock. It will read/write register to enable/disable clock. Also
there is no other device of mt8192 using MSDC controller.
We add mmc nodes for mt8192 SoC and remove the clock-controller in
dts for avoid a duplicate unit-address(11f60000) warning.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220407113703.26423-2-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The driver data of MT8183 and MT8173 are different.
The value of has_gamma for MT8173 is true while the value of MT8183 is
false. Therefore, the compatible of disp_aal for MT8183 is not suitable
for the compatible for MT8173.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220411035843.19847-3-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT6359 is the primary PMIC for MT8192.
Add PMIC MT6359 related node which is used for MT8192 platform.
Signed-off-by: Hui Liu <hui.liu@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220421012623.3446-2-hui.liu@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The power of encoder is not control by mediatek,larb, so we add
power domain to encoder nodes for mt8173 SoC.
Signed-off-by: Irui Wang <irui.wang@mediatek.com>
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Link: https://lore.kernel.org/r/20220421035111.7267-4-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
After adding device_link between the IOMMU consumer and smi,
the mediatek,larb is unnecessary now.
CC: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220421035111.7267-3-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Align the name of thermal zone node to dtschema to fix warnings like:
arch/arm64/boot/dts/mediatek/mt8173-elm.dt.yaml:
thermal-zones: 'cpu_thermal' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20210820081616.83674-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Align the name of operating-points node to dtschema to fix warnings like:
arch/arm64/boot/dts/mediatek/mt8173-elm.dt.yaml:
opp_table0: $nodename:0: 'opp_table0' does not match '^opp-table(-[a-z0-9]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20210820081616.83674-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
dtschema expects PWM node name to be a generic "pwm". This also matches
Devicetree specification requirements about generic node names.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220214081916.162014-3-krzysztof.kozlowski@canonical.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Rely on standard cci-control-port property to identify CCI port
reference.
Update mt7622 dts binding.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce wed0 and wed1 nodes in order to enable offloading forwarding
between ethernet and wireless devices on the mt7622 chipset.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
It improves performance by eliminating the need for a cache flush on rx and tx
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PCIe node for mt8192 SoC.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220330133816.30806-2-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add m4u and smi nodes for mt8192 SoC
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220318144534.17996-15-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add efuse node for mt8192 SoC
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220318144534.17996-12-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add xhci node for mt8192 SoC.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220318144534.17996-7-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add xhci node for mt8192 SoC.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220318144534.17996-6-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add SCP node for mt8192 SoC.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220318144534.17996-5-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add pwrap node for mt8192 SoC.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220318144534.17996-2-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Commit 39bd2b6a37 ("dt-bindings: Improve phandle-array schemas")
updated the mediatek,larbs property in the mediatek,iommu.yaml
dt-binding to make it clearer that the phandles passed to the property
are independent, rather than subsequent arguments to the first phandle.
Update the mediatek,larbs property in the arm64 Devicetrees to use the
same formatting. This change doesn't impact any behavior: the compiled
dtb is exactly the same. It does however fix the warnings generated by
dtbs_check.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220301203147.1143782-2-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Core
----
- Introduce XDP multi-buffer support, allowing the use of XDP with
jumbo frame MTUs and combination with Rx coalescing offloads (LRO).
- Speed up netns dismantling (5x) and lower the memory cost a little.
Remove unnecessary per-netns sockets. Scope some lists to a netns.
Cut down RCU syncing. Use batch methods. Allow netdev registration
to complete out of order.
- Support distinguishing timestamp types (ingress vs egress) and
maintaining them across packet scrubbing points (e.g. redirect).
- Continue the work of annotating packet drop reasons throughout
the stack.
- Switch netdev error counters from an atomic to dynamically
allocated per-CPU counters.
- Rework a few preempt_disable(), local_irq_save() and busy waiting
sections problematic on PREEMPT_RT.
- Extend the ref_tracker to allow catching use-after-free bugs.
BPF
---
- Introduce "packing allocator" for BPF JIT images. JITed code is
marked read only, and used to be allocated at page granularity.
Custom allocator allows for more efficient memory use, lower
iTLB pressure and prevents identity mapping huge pages from
getting split.
- Make use of BTF type annotations (e.g. __user, __percpu) to enforce
the correct probe read access method, add appropriate helpers.
- Convert the BPF preload to use light skeleton and drop
the user-mode-driver dependency.
- Allow XDP BPF_PROG_RUN test infra to send real packets, enabling
its use as a packet generator.
- Allow local storage memory to be allocated with GFP_KERNEL if called
from a hook allowed to sleep.
- Introduce fprobe (multi kprobe) to speed up mass attachment (arch
bits to come later).
- Add unstable conntrack lookup helpers for BPF by using the BPF
kfunc infra.
- Allow cgroup BPF progs to return custom errors to user space.
- Add support for AF_UNIX iterator batching.
- Allow iterator programs to use sleepable helpers.
- Support JIT of add, and, or, xor and xchg atomic ops on arm64.
- Add BTFGen support to bpftool which allows to use CO-RE in kernels
without BTF info.
- Large number of libbpf API improvements, cleanups and deprecations.
Protocols
---------
- Micro-optimize UDPv6 Tx, gaining up to 5% in test on dummy netdev.
- Adjust TSO packet sizes based on min_rtt, allowing very low latency
links (data centers) to always send full-sized TSO super-frames.
- Make IPv6 flow label changes (AKA hash rethink) more configurable,
via sysctl and setsockopt. Distinguish between server and client
behavior.
- VxLAN support to "collect metadata" devices to terminate only
configured VNIs. This is similar to VLAN filtering in the bridge.
- Support inserting IPv6 IOAM information to a fraction of frames.
- Add protocol attribute to IP addresses to allow identifying where
given address comes from (kernel-generated, DHCP etc.)
- Support setting socket and IPv6 options via cmsg on ping6 sockets.
- Reject mis-use of ECN bits in IP headers as part of DSCP/TOS.
Define dscp_t and stop taking ECN bits into account in fib-rules.
- Add support for locked bridge ports (for 802.1X).
- tun: support NAPI for packets received from batched XDP buffs,
doubling the performance in some scenarios.
- IPv6 extension header handling in Open vSwitch.
- Support IPv6 control message load balancing in bonding, prevent
neighbor solicitation and advertisement from using the wrong port.
Support NS/NA monitor selection similar to existing ARP monitor.
- SMC
- improve performance with TCP_CORK and sendfile()
- support auto-corking
- support TCP_NODELAY
- MCTP (Management Component Transport Protocol)
- add user space tag control interface
- I2C binding driver (as specified by DMTF DSP0237)
- Multi-BSSID beacon handling in AP mode for WiFi.
- Bluetooth:
- handle MSFT Monitor Device Event
- add MGMT Adv Monitor Device Found/Lost events
- Multi-Path TCP:
- add support for the SO_SNDTIMEO socket option
- lots of selftest cleanups and improvements
- Increase the max PDU size in CAN ISOTP to 64 kB.
Driver API
----------
- Add HW counters for SW netdevs, a mechanism for devices which
offload packet forwarding to report packet statistics back to
software interfaces such as tunnels.
- Select the default NIC queue count as a fraction of number of
physical CPU cores, instead of hard-coding to 8.
- Expose devlink instance locks to drivers. Allow device layer of
drivers to use that lock directly instead of creating their own
which always runs into ordering issues in devlink callbacks.
- Add header/data split indication to guide user space enabling
of TCP zero-copy Rx.
- Allow configuring completion queue event size.
- Refactor page_pool to enable fragmenting after allocation.
- Add allocation and page reuse statistics to page_pool.
- Improve Multiple Spanning Trees support in the bridge to allow
reuse of topologies across VLANs, saving HW resources in switches.
- DSA (Distributed Switch Architecture):
- replay and offload of host VLAN entries
- offload of static and local FDB entries on LAG interfaces
- FDB isolation and unicast filtering
New hardware / drivers
----------------------
- Ethernet:
- LAN937x T1 PHYs
- Davicom DM9051 SPI NIC driver
- Realtek RTL8367S, RTL8367RB-VB switch and MDIO
- Microchip ksz8563 switches
- Netronome NFP3800 SmartNICs
- Fungible SmartNICs
- MediaTek MT8195 switches
- WiFi:
- mt76: MediaTek mt7916
- mt76: MediaTek mt7921u USB adapters
- brcmfmac: Broadcom BCM43454/6
- Mobile:
- iosm: Intel M.2 7360 WWAN card
Drivers
-------
- Convert many drivers to the new phylink API built for split PCS
designs but also simplifying other cases.
- Intel Ethernet NICs:
- add TTY for GNSS module for E810T device
- improve AF_XDP performance
- GTP-C and GTP-U filter offload
- QinQ VLAN support
- Mellanox Ethernet NICs (mlx5):
- support xdp->data_meta
- multi-buffer XDP
- offload tc push_eth and pop_eth actions
- Netronome Ethernet NICs (nfp):
- flow-independent tc action hardware offload (police / meter)
- AF_XDP
- Other Ethernet NICs:
- at803x: fiber and SFP support
- xgmac: mdio: preamble suppression and custom MDC frequencies
- r8169: enable ASPM L1.2 if system vendor flags it as safe
- macb/gem: ZynqMP SGMII
- hns3: add TX push mode
- dpaa2-eth: software TSO
- lan743x: multi-queue, mdio, SGMII, PTP
- axienet: NAPI and GRO support
- Mellanox Ethernet switches (mlxsw):
- source and dest IP address rewrites
- RJ45 ports
- Marvell Ethernet switches (prestera):
- basic routing offload
- multi-chain TC ACL offload
- NXP embedded Ethernet switches (ocelot & felix):
- PTP over UDP with the ocelot-8021q DSA tagging protocol
- basic QoS classification on Felix DSA switch using dcbnl
- port mirroring for ocelot switches
- Microchip high-speed industrial Ethernet (sparx5):
- offloading of bridge port flooding flags
- PTP Hardware Clock
- Other embedded switches:
- lan966x: PTP Hardward Clock
- qca8k: mdio read/write operations via crafted Ethernet packets
- Qualcomm 802.11ax WiFi (ath11k):
- add LDPC FEC type and 802.11ax High Efficiency data in radiotap
- enable RX PPDU stats in monitor co-exist mode
- Intel WiFi (iwlwifi):
- UHB TAS enablement via BIOS
- band disablement via BIOS
- channel switch offload
- 32 Rx AMPDU sessions in newer devices
- MediaTek WiFi (mt76):
- background radar detection
- thermal management improvements on mt7915
- SAR support for more mt76 platforms
- MBSSID and 6 GHz band on mt7915
- RealTek WiFi:
- rtw89: AP mode
- rtw89: 160 MHz channels and 6 GHz band
- rtw89: hardware scan
- Bluetooth:
- mt7921s: wake on Bluetooth, SCO over I2S, wide-band-speed (WBS)
- Microchip CAN (mcp251xfd):
- multiple RX-FIFOs and runtime configurable RX/TX rings
- internal PLL, runtime PM handling simplification
- improve chip detection and error handling after wakeup
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ELpe
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"The sprinkling of SPI drivers is because we added a new one and Mark
sent us a SPI driver interface conversion pull request.
Core
----
- Introduce XDP multi-buffer support, allowing the use of XDP with
jumbo frame MTUs and combination with Rx coalescing offloads (LRO).
- Speed up netns dismantling (5x) and lower the memory cost a little.
Remove unnecessary per-netns sockets. Scope some lists to a netns.
Cut down RCU syncing. Use batch methods. Allow netdev registration
to complete out of order.
- Support distinguishing timestamp types (ingress vs egress) and
maintaining them across packet scrubbing points (e.g. redirect).
- Continue the work of annotating packet drop reasons throughout the
stack.
- Switch netdev error counters from an atomic to dynamically
allocated per-CPU counters.
- Rework a few preempt_disable(), local_irq_save() and busy waiting
sections problematic on PREEMPT_RT.
- Extend the ref_tracker to allow catching use-after-free bugs.
BPF
---
- Introduce "packing allocator" for BPF JIT images. JITed code is
marked read only, and used to be allocated at page granularity.
Custom allocator allows for more efficient memory use, lower iTLB
pressure and prevents identity mapping huge pages from getting
split.
- Make use of BTF type annotations (e.g. __user, __percpu) to enforce
the correct probe read access method, add appropriate helpers.
- Convert the BPF preload to use light skeleton and drop the
user-mode-driver dependency.
- Allow XDP BPF_PROG_RUN test infra to send real packets, enabling
its use as a packet generator.
- Allow local storage memory to be allocated with GFP_KERNEL if
called from a hook allowed to sleep.
- Introduce fprobe (multi kprobe) to speed up mass attachment (arch
bits to come later).
- Add unstable conntrack lookup helpers for BPF by using the BPF
kfunc infra.
- Allow cgroup BPF progs to return custom errors to user space.
- Add support for AF_UNIX iterator batching.
- Allow iterator programs to use sleepable helpers.
- Support JIT of add, and, or, xor and xchg atomic ops on arm64.
- Add BTFGen support to bpftool which allows to use CO-RE in kernels
without BTF info.
- Large number of libbpf API improvements, cleanups and deprecations.
Protocols
---------
- Micro-optimize UDPv6 Tx, gaining up to 5% in test on dummy netdev.
- Adjust TSO packet sizes based on min_rtt, allowing very low latency
links (data centers) to always send full-sized TSO super-frames.
- Make IPv6 flow label changes (AKA hash rethink) more configurable,
via sysctl and setsockopt. Distinguish between server and client
behavior.
- VxLAN support to "collect metadata" devices to terminate only
configured VNIs. This is similar to VLAN filtering in the bridge.
- Support inserting IPv6 IOAM information to a fraction of frames.
- Add protocol attribute to IP addresses to allow identifying where
given address comes from (kernel-generated, DHCP etc.)
- Support setting socket and IPv6 options via cmsg on ping6 sockets.
- Reject mis-use of ECN bits in IP headers as part of DSCP/TOS.
Define dscp_t and stop taking ECN bits into account in fib-rules.
- Add support for locked bridge ports (for 802.1X).
- tun: support NAPI for packets received from batched XDP buffs,
doubling the performance in some scenarios.
- IPv6 extension header handling in Open vSwitch.
- Support IPv6 control message load balancing in bonding, prevent
neighbor solicitation and advertisement from using the wrong port.
Support NS/NA monitor selection similar to existing ARP monitor.
- SMC
- improve performance with TCP_CORK and sendfile()
- support auto-corking
- support TCP_NODELAY
- MCTP (Management Component Transport Protocol)
- add user space tag control interface
- I2C binding driver (as specified by DMTF DSP0237)
- Multi-BSSID beacon handling in AP mode for WiFi.
- Bluetooth:
- handle MSFT Monitor Device Event
- add MGMT Adv Monitor Device Found/Lost events
- Multi-Path TCP:
- add support for the SO_SNDTIMEO socket option
- lots of selftest cleanups and improvements
- Increase the max PDU size in CAN ISOTP to 64 kB.
Driver API
----------
- Add HW counters for SW netdevs, a mechanism for devices which
offload packet forwarding to report packet statistics back to
software interfaces such as tunnels.
- Select the default NIC queue count as a fraction of number of
physical CPU cores, instead of hard-coding to 8.
- Expose devlink instance locks to drivers. Allow device layer of
drivers to use that lock directly instead of creating their own
which always runs into ordering issues in devlink callbacks.
- Add header/data split indication to guide user space enabling of
TCP zero-copy Rx.
- Allow configuring completion queue event size.
- Refactor page_pool to enable fragmenting after allocation.
- Add allocation and page reuse statistics to page_pool.
- Improve Multiple Spanning Trees support in the bridge to allow
reuse of topologies across VLANs, saving HW resources in switches.
- DSA (Distributed Switch Architecture):
- replay and offload of host VLAN entries
- offload of static and local FDB entries on LAG interfaces
- FDB isolation and unicast filtering
New hardware / drivers
----------------------
- Ethernet:
- LAN937x T1 PHYs
- Davicom DM9051 SPI NIC driver
- Realtek RTL8367S, RTL8367RB-VB switch and MDIO
- Microchip ksz8563 switches
- Netronome NFP3800 SmartNICs
- Fungible SmartNICs
- MediaTek MT8195 switches
- WiFi:
- mt76: MediaTek mt7916
- mt76: MediaTek mt7921u USB adapters
- brcmfmac: Broadcom BCM43454/6
- Mobile:
- iosm: Intel M.2 7360 WWAN card
Drivers
-------
- Convert many drivers to the new phylink API built for split PCS
designs but also simplifying other cases.
- Intel Ethernet NICs:
- add TTY for GNSS module for E810T device
- improve AF_XDP performance
- GTP-C and GTP-U filter offload
- QinQ VLAN support
- Mellanox Ethernet NICs (mlx5):
- support xdp->data_meta
- multi-buffer XDP
- offload tc push_eth and pop_eth actions
- Netronome Ethernet NICs (nfp):
- flow-independent tc action hardware offload (police / meter)
- AF_XDP
- Other Ethernet NICs:
- at803x: fiber and SFP support
- xgmac: mdio: preamble suppression and custom MDC frequencies
- r8169: enable ASPM L1.2 if system vendor flags it as safe
- macb/gem: ZynqMP SGMII
- hns3: add TX push mode
- dpaa2-eth: software TSO
- lan743x: multi-queue, mdio, SGMII, PTP
- axienet: NAPI and GRO support
- Mellanox Ethernet switches (mlxsw):
- source and dest IP address rewrites
- RJ45 ports
- Marvell Ethernet switches (prestera):
- basic routing offload
- multi-chain TC ACL offload
- NXP embedded Ethernet switches (ocelot & felix):
- PTP over UDP with the ocelot-8021q DSA tagging protocol
- basic QoS classification on Felix DSA switch using dcbnl
- port mirroring for ocelot switches
- Microchip high-speed industrial Ethernet (sparx5):
- offloading of bridge port flooding flags
- PTP Hardware Clock
- Other embedded switches:
- lan966x: PTP Hardward Clock
- qca8k: mdio read/write operations via crafted Ethernet packets
- Qualcomm 802.11ax WiFi (ath11k):
- add LDPC FEC type and 802.11ax High Efficiency data in radiotap
- enable RX PPDU stats in monitor co-exist mode
- Intel WiFi (iwlwifi):
- UHB TAS enablement via BIOS
- band disablement via BIOS
- channel switch offload
- 32 Rx AMPDU sessions in newer devices
- MediaTek WiFi (mt76):
- background radar detection
- thermal management improvements on mt7915
- SAR support for more mt76 platforms
- MBSSID and 6 GHz band on mt7915
- RealTek WiFi:
- rtw89: AP mode
- rtw89: 160 MHz channels and 6 GHz band
- rtw89: hardware scan
- Bluetooth:
- mt7921s: wake on Bluetooth, SCO over I2S, wide-band-speed (WBS)
- Microchip CAN (mcp251xfd):
- multiple RX-FIFOs and runtime configurable RX/TX rings
- internal PLL, runtime PM handling simplification
- improve chip detection and error handling after wakeup"
* tag 'net-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2521 commits)
llc: fix netdevice reference leaks in llc_ui_bind()
drivers: ethernet: cpsw: fix panic when interrupt coaleceing is set via ethtool
ice: don't allow to run ice_send_event_to_aux() in atomic ctx
ice: fix 'scheduling while atomic' on aux critical err interrupt
net/sched: fix incorrect vlan_push_eth dest field
net: bridge: mst: Restrict info size queries to bridge ports
net: marvell: prestera: add missing destroy_workqueue() in prestera_module_init()
drivers: net: xgene: Fix regression in CRC stripping
net: geneve: add missing netlink policy and size for IFLA_GENEVE_INNER_PROTO_INHERIT
net: dsa: fix missing host-filtered multicast addresses
net/mlx5e: Fix build warning, detected write beyond size of field
iwlwifi: mvm: Don't fail if PPAG isn't supported
selftests/bpf: Fix kprobe_multi test.
Revert "rethook: x86: Add rethook x86 implementation"
Revert "arm64: rethook: Add arm64 rethook implementation"
Revert "powerpc: Add rethook support"
Revert "ARM: rethook: Add rethook arm implementation"
netdevice: add missing dm_private kdoc
net: bridge: mst: prevent NULL deref in br_mst_info_size()
selftests: forwarding: Use same VRF for port and VLAN upper
...
Since there are some changes in ethernet driver:
update ethernet device node in dts to accommodate to it.
1. stmmac_probe_config_dt() in stmmac_platform.c will initialize specified
parameters according to compatible string "snps,dwmac-4.20a", then,
dwmac-mediatek.c can skip the initialization if add compatible string
"snps,dwmac-4.20a" in eth device node.
2. commit 882007ed78 ("net-next: dt-binding: dwmac-mediatek: add more
description for RMII") added rmii internal support, we should add
corresponding clocks/clocks-names in eth device node.
3. add "snps,reset-delays-us = <0 10000 10000>;" to ensure reset delay
can meet PHY requirement.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the format of memory node in DT adding the
device_type.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Link: https://lore.kernel.org/r/20220119123537.9968-3-sam.shih@mediatek.com
[mb: fixed commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch updates the format of memory node in DT adding the correct
device_type.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Link: https://lore.kernel.org/r/20220119123537.9968-2-sam.shih@mediatek.com
[mb: fixed commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add power domains controller node for SoC mt8192
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Chun-Jie Chen <chun-jie.chen@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20210825010426.30303-1-chun-jie.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add watchdog device node to MT8192 SoC.
Signed-off-by: Allen-KH Cheng <Allen-KH.Cheng@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220207094024.22674-1-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
When the initial devicetree for mt8192 was added in 48489980e2 ("arm64:
dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile"), the
clock driver for mt8192 was not yet upstream, so the clock property nodes
were set to the clk26m clock as a placeholder.
Given that the clock driver has since been added through 710573dee3 ("clk:
mediatek: Add MT8192 basic clocks support"), as well as its dt-bindings
through f35f1a23e0 ("clk: mediatek: Add dt-bindings of MT8192 clocks") and
devicetree nodes through 5d2b897bc6 ("arm64: dts: mediatek: Add mt8192
clock controllers"), fix the systimer clock property to point to the actual
clock.
Signed-off-by: Allen-KH Cheng <Allen-KH.Cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220113065822.11809-6-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
When the initial devicetree for mt8192 was added in 48489980e2 ("arm64:
dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile"), the
clock driver for mt8192 was not yet upstream, so the clock property nodes
were set to the clk26m clock as a placeholder.
Given that the clock driver has since been added through 710573dee3 ("clk:
mediatek: Add MT8192 basic clocks support"), as well as its dt-bindings
through f35f1a23e0 ("clk: mediatek: Add dt-bindings of MT8192 clocks") and
devicetree nodes through 5d2b897bc6 ("arm64: dts: mediatek: Add mt8192
clock controllers"), fix the I2C clock property to point to the actual
clock.
Signed-off-by: Allen-KH Cheng <Allen-KH.Cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220113065822.11809-5-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
When the initial devicetree for mt8192 was added in 48489980e2 ("arm64:
dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile"), the
clock driver for mt8192 was not yet upstream, so the clock property nodes
were set to the clk26m clock as a placeholder.
Given that the clock driver has since been added through 710573dee3 ("clk:
mediatek: Add MT8192 basic clocks support"), as well as its dt-bindings
through f35f1a23e0 ("clk: mediatek: Add dt-bindings of MT8192 clocks") and
devicetree nodes through 5d2b897bc6 ("arm64: dts: mediatek: Add mt8192
clock controllers"), fix the Nor Flash clock property to point to the actual
clock.
Signed-off-by: Allen-KH Cheng <Allen-KH.Cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220113065822.11809-4-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
When the initial devicetree for mt8192 was added in 48489980e2 ("arm64:
dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile"), the
clock driver for mt8192 was not yet upstream, so the clock property nodes
were set to the clk26m clock as a placeholder.
Given that the clock driver has since been added through 710573dee3 ("clk:
mediatek: Add MT8192 basic clocks support"), as well as its dt-bindings
through f35f1a23e0 ("clk: mediatek: Add dt-bindings of MT8192 clocks") and
devicetree nodes through 5d2b897bc6 ("arm64: dts: mediatek: Add mt8192
clock controllers"), fix the SPI clock property to point to the actual
clock.
Signed-off-by: Allen-KH Cheng <Allen-KH.Cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220113065822.11809-3-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
When the initial devicetree for mt8192 was added in 48489980e2 ("arm64:
dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile"), the
clock driver for mt8192 was not yet upstream, so the clock property nodes
were set to the clk26m clock as a placeholder.
Given that the clock driver has since been added through 710573dee3 ("clk:
mediatek: Add MT8192 basic clocks support"), as well as its dt-bindings
through f35f1a23e0 ("clk: mediatek: Add dt-bindings of MT8192 clocks") and
devicetree nodes through 5d2b897bc6 ("arm64: dts: mediatek: Add mt8192
clock controllers"), fix the uart clock property to point to the actual
clock.
Signed-off-by: Allen-KH Cheng <Allen-KH.Cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220113065822.11809-2-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a node describing the USB Type C connector, in order to utilize the
Chromium OS USB Type-C driver that enumerates Type-C ports and connected
cables/peripherals and makes them visible to userspace.
Cc: Alexandru M Stan <amstan@chromium.org>
Cc: Benson Leung <bleung@chromium.org>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20211209195112.366176-1-pmalani@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add basic chip support for Mediatek mt7986, include
basic uart nodes, rng node and watchdog node.
Add cpu node, timer node, gic node, psci and reserved-memory node
for ARM Trusted Firmware.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Link: https://lore.kernel.org/r/20211122123222.8016-3-sam.shih@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
According to auxadc change the readback value from raw data to Vsense.
Update the tboard table that temperature map to Vsense.
pull-up voltage: 1800 mv
pull-up resistor: 75K
Vsense = pull-up voltage * Rntc / ( pull-up resistor + Rntc )
Signed-off-by: Ben Tseng <ben.tseng@mediatek.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20211103033044.2777-1-ben.tseng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add fennel sku7 and fennel14 sku2, which use different audio codec than
previous fennel/fennel14 boards.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20211110063118.3412564-3-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The two clocks "main-source" and "main-sel" are not present in the
driver and not defined in the binding documentation. Remove them
as they are not used and not described in the documentation.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Link: https://lore.kernel.org/r/20211110193520.488-1-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fix the i2c node names to be compliant to the YAML schema. The
I2C node name should match the following pattern: "^i2c@[0-9a-f]+$".
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Link: https://lore.kernel.org/r/20211110194959.20611-4-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The the rpmsg property name is changed to "mediatek," to sync with the
vendor name defined in vendor-prefixes.yaml.
Signed-off-by: Tinghan Shen <tinghan.shen@mediatek.com>
Reviewed-By: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20210924033935.2127-7-tinghan.shen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Reset the DSI hardware is needed to prevent different settings between
the bootloader and the kernel.
While here, also remove the undocumented and also not used
'mediatek,syscon-dsi' property.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210930103105.v4.5.I933f1532d7a1b2910843a9644c86a7d94a4b44e1@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The DT binding includes for reset controllers are located in
include/dt-bindings/reset/. Move the Mediatek reset constants in there.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20210930103105.v4.1.I514d9aafff3a062f751b37d3fea7402f67595b86@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
There are two independent PCIe controllers in MT2712 and MT7622
platform. Each of them should contain an independent MSI domain.
In old dts architecture, MSI domain will be inherited from the root
bridge, and all of the devices will share the same MSI domain.
Hence that, the PCIe devices will not work properly if the irq number
which required is more than 32.
Split the PCIe node for MT2712 and MT7622 platform to comply with
the hardware design and fix MSI issue.
Signed-off-by: Chuanjia Liu <chuanjia.liu@mediatek.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Link: https://lore.kernel.org/r/20210823032800.1660-6-chuanjia.liu@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Set pin control for the SoC sound node.
The compatibles are set by each model dts.
The codecs that each models use are:
burnet ts3a227_max98357
damu da7219_max98357
fennel da7219_rt1015p
fennel14 da7219_rt1015p
juniper ts3a227_max98357
kakadu da7219_rt1015p
kappa ts3a227_max98357
kenzo ts3a227_max98357
kodama ts3a227_max98357
krane ts3a227_max98357
willow-sku0 da7219_max98357
willow-sku1 ts3a227_max98357
Signed-off-by: Kansho Nishida <kansho@chromium.org>
Link: https://lore.kernel.org/r/20210706190111.v3.2.I6e9ce0f2a489f9a52299656cd966b38ae75e7552@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
no core changes at all this time, just driver work!
New drivers:
- New subdriver for Intel Keem Bay (an ARM-based SoC)
- New subdriver for Qualcomm MDM9607 and SM6115
- New subdriver for ST Microelectronics STM32MP135
- New subdriver for Freescale i.MX8ULP ("Ultra Low Power")
- New subdriver for Ingenic X2100
- Support for Qualcomm PMC8180, PMC8180C, SA8155p-adp PMIC GPIO
- Support Samsung Exynos850
- Support Renesas RZ/G2L
Enhancements:
- A major refactoring of the Rockchip driver, breaking part of it out
to a separate GPIO driver in drivers/gpio
- Pin bias support on Renesas r8a77995
- Add SCI pins support to Ingenic JZ4755 and JZ4760
- Mediatek device tree bindings converted to YAML
-----BEGIN PGP SIGNATURE-----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=I6N/
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.15 kernel cycle, no
core changes at all this time, just driver work!
New drivers:
- New subdriver for Intel Keem Bay (an ARM-based SoC)
- New subdriver for Qualcomm MDM9607 and SM6115
- New subdriver for ST Microelectronics STM32MP135
- New subdriver for Freescale i.MX8ULP ("Ultra Low Power")
- New subdriver for Ingenic X2100
- Support for Qualcomm PMC8180, PMC8180C, SA8155p-adp PMIC GPIO
- Support Samsung Exynos850
- Support Renesas RZ/G2L
Enhancements:
- A major refactoring of the Rockchip driver, breaking part of it out
to a separate GPIO driver in drivers/gpio
- Pin bias support on Renesas r8a77995
- Add SCI pins support to Ingenic JZ4755 and JZ4760
- Mediatek device tree bindings converted to YAML"
* tag 'pinctrl-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (53 commits)
pinctrl: renesas: Add RZ/G2L pin and gpio controller driver
pinctrl: samsung: Add Exynos850 SoC specific data
dt-bindings: pinctrl: samsung: Add Exynos850 doc
MAINTAINERS: Add maintainers for amd-pinctrl driver
pinctrl: Add Intel Keem Bay pinctrl driver
dt-bindings: pinctrl: Add bindings for Intel Keembay pinctrl driver
pinctrl: zynqmp: Drop pinctrl_unregister for devm_ registered device
dt-bindings: pinctrl: qcom-pmic-gpio: Remove the interrupts property
dt-bindings: pinctrl: qcom-pmic-gpio: Convert qcom pmic gpio bindings to YAML
dt-bindings: pinctrl: mt8195: Use real world values for drive-strength arguments
dt-bindings: mediatek: convert pinctrl to yaml
arm: dts: mt8183: Move pinfunc to include/dt-bindings/pinctrl
arm: dts: mt8135: Move pinfunc to include/dt-bindings/pinctrl
pinctrl: ingenic: Add .max_register in regmap_config
pinctrl: ingenic: Fix bias config for X2000(E)
pinctrl: ingenic: Fix incorrect pull up/down info
pinctrl: Ingenic: Add pinctrl driver for X2100.
dt-bindings: pinctrl: Add bindings for Ingenic X2100.
pinctrl: Ingenic: Add SSI pins support for JZ4755 and JZ4760.
pinctrl: Ingenic: Improve the code.
...
Move mt8183-pinfunc.h into include/dt-bindings/pinctrl so that we can
include it in yaml examples.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20210804044033.3047296-2-hsinyi@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
da9211 regulator needs to be enabled before enabling the mfg_async power
domain. Otherwise the subdomain is not enabled and causes failure in
imgtec gpu driver boot.
Add the "domain-supply" property to the "mfg_async" node in DT.
Signed-off-by: Bilal Wasim <Bilal.Wasim@imgtec.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210701114012.RESEND.3.I9e27871bb700c807a564957302b292e9935dae0b@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
With commit 1796164fac ("dt-bindings: mmc: document alias support"),
a way to specify fixed index numbers was provided. This patch use aliases
to mmc nodes so the partition name for eMMC and SD card will be consistent
across boots.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20210728040710.2891955-2-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
With commit 1796164fac ("dt-bindings: mmc: document alias support"),
a way to specify fixed index numbers was provided. This patch use aliases
to mmc nodes so the partition name for eMMC and SD card will be consistent
across boots.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20210728040710.2891955-1-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a basic GPU node for mt8183, as well as OPP table.
Note that with the current panfrost driver, devfreq is not
actually functional, as the we do not have platform-specific
support for >1 supplies. Also, we are missing code to handle
frequency change, as the GPU frequency needs to be switched
away to a stable 26Mhz clock during the transition.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Link: https://lore.kernel.org/r/20210521200038.v14.1.I9f45f5c1f975422d58b5904d11546349e9ccdc94@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add tboard thermal zones.
The tboard thermal sensors are a kind of NTC sensors which are located
on PCB board to correlate the temperature of the case (Tskin).
pull-up voltage: 1800 mv
pull-up resistor: 75K
Vsense = pull-up voltage * Rntc / ( pull-up resistor + Rntc )
AuxIn = Vsense * 4096 / 1500
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Signed-off-by: Ben Tseng <ben.tseng@mediatek.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20210604093755.13288-1-ben.tseng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a 'cbas' device node for supporting tablet mode switch in
kukui devices.
Kukui platforms with detacheable base have an additional input
device under cros-ec, which reports SW_TABLET_MODE regarding
its base state (e.g. base flipped or detached).
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210609032554.2443675-1-ikjn@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
We don't need to register smi_common as syscon. Also add required
property power-domains for this node.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210601040014.2970805-1-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fennel is known as Lenovo IdeaPad Flex 3 Chromebook.
Fennel14 is known as Lenovo IdeaPad 3 Chromebook.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20210421090601.730744-11-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Kenzo is known as Acer Chromebook 311.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210421090601.730744-10-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Burnet is known as HP Chromebook x360 11MK G3 EE
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210421090601.730744-9-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Willow is known as Acer Chromebook 311 (C722/C722T)
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210421090601.730744-8-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Kappa is known as HP Chromebook 11a
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210421090601.730744-7-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add larb nodes for MT8167:
* larb0 is used for display (dsi and hdmi)
* larb1 is used for camera (csi)
* larb2 is used for the video hardware decoder
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Link: https://lore.kernel.org/r/20210406113631.2675029-1-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
There are two separate hardware encoder blocks inside MT8173.
Split the current mtk-vcodec-enc node to match the hardware architecture.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Maoguang Meng <maoguang.meng@mediatek.com>
Signed-off-by: Irui Wang <irui.wang@mediatek.com>
Acked-by: Tiffany Lin <tiffany.lin@mediatek.com>
Link: https://lore.kernel.org/r/20210325122625.15100-2-irui.wang@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The MT8183 Pumpkin board is manufactured by OLogic and includes
a MediaTek MT8183 SoC with 2GB of RAM.
The board provides the following IOs:
* 2 USB Type-A ports
* Ethernet
* Serial UART over micro-USB port
* 1 USB Type-C dual role port
* 1 USB Type-C power only port
* 1 Jack for audio
* RPI compatible header
* MT7668 wiresless chip with Wi-Fi AC and BT 5
* Micro-HDMI port
* 2 connectors for CSI cameras
* 1 connector for DSI display
* 1 JTAG port
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Link: https://lore.kernel.org/r/20210217205945.830006-2-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Kakadu is also known as ASUS Chromebook Detachable CM3.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20210331091327.1198529-3-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Due to power domain controller is added, the power domain's
phanle is also changed from 'scpsys' to 'spm', but forget to
modify pmic node's
Fixes: 8b6562644d ("arm64: dts: mediatek: Add mt8173 power domain controller")
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/1616048328-13579-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add two passive trip points at 68°C and 80°C for the CPU temperature.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add thermal zone node to Mediatek MT8183 dts file.
Evaluate the thermal zone every 500ms while not cooling
and every 100ms when passive cooling is performed.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This is used to fix dtbs_check warning:
harmonize node names and compatibles;
add property "usb-role-switch" for connector dependence.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210316092232.9806-8-chunfeng.yun@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The header file of GCE should be for MT8183 SoC instead of MT8173.
Fixes: 91f9c963ce ("arm64: dts: mt8183: Add display nodes for MT8183")
Reported-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://lore.kernel.org/r/20210131101726.804-1-matthias.bgg@kernel.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Similar to krane-sku176 but using a different panel source.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210113110400.616319-2-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Config dsi node for mt8183 kukui. Set panel and ports.
Several kukui boards share the same panel property and only compatible
is different. So compatible will be set in board dts for comparison
convenience.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Link: https://lore.kernel.org/r/20210113110400.616319-1-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The MT8183 display PWM device will not work until the associated
power-domain is enabled. Add the power-domain reference to the node
allows the display PWM driver to operate and the backlight turn on.
Fixes: f15722c0fe ("arm64: dts: mt8183: Add pwm and backlight node")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20210113215723.71966-1-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
property name must include only lowercase and '-'
Fixes: 91f9c963ce ("arm64: dts: mt8183: Add display nodes for MT8183")
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210128112314.1304160-2-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MDI_TP_P0 (gpio51) is used by pwm1 and uart2 (uart1 on gpio-header)
MDI_RP_P4 (gpio67) is used by pwm4 and spi1
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20201016204019.2606-3-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
mt7622 only supports 6 pwm-channels so drop pwm7
third pwm (pwm2) is inverted and connected to fan-socket
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20201016204019.2606-2-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
