Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add pinmux support for UART1 on MediatekX20 Development board based
on Mediatek MT6797 SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a fragment,
that later gets filled in on later releases, and in some cases it's
near-complete platform support. The latter is more common for derivative
platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions. Allwinner
support for F1C100s, a quite old SoC (ARMv5-based) shipping in the
Lychee Pi Nano platform. At the other end is NXP Layerscape LX2160A,
a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O aimed at
infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to devicetree,
which opens up for removal of even more of their platform-specific
'hwmod' description tables over the next few releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board
-----BEGIN PGP SIGNATURE-----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=sFVi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a
fragment, that later gets filled in on later releases, and in some
cases it's near-complete platform support. The latter is more common
for derivative platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions.
Allwinner support for F1C100s, a quite old SoC (ARMv5-based) shipping
in the Lychee Pi Nano platform. At the other end is NXP Layerscape
LX2160A, a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O
aimed at infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to
devicetree, which opens up for removal of even more of their
platform-specific 'hwmod' description tables over the next few
releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (648 commits)
ARM: dts: suniv: Fix improper bindings include patch
ARM: dts: sunxi: Enable Broadcom-based Bluetooth for multiple boards
arm64: dts: allwinner: a64: bananapi-m64: Add Bluetooth device node
ARM: dts: suniv: Fix improper bindings include patch
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Remove unused properties from FSL QSPI driver nodes
arm64: dts: ti: k3-am654: Enable main domain McSPI0
arm64: dts: ti: k3-am654: Add McSPI DT nodes
arm64: dts: ti: k3-am654: Populate power-domain property for UART nodes
arm64: dts: ti: k3-am654-base-board: Enable ECAP PWM
arm64: dts: ti: k3-am65-main: Add ECAP PWM node
arm64: dts: ti: k3-am654-base-board: Add I2C nodes
arm64: dts: ti: am654-base-board: Add pinmux for main uart0
arm64: dts: ti: k3-am65: Add pinctrl regions
dt-bindings: pinctrl: k3: Introduce pinmux definitions
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
...
The "num-lanes" property for PCIe is not used, remove it.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This patch adds the device node of the GCE hardware for CMDQ module.
Signed-off-by: Houlong Wei <houlong.wei@mediatek.com>
Signed-off-by: HS Liao <hs.liao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MediaTeks general purpose timer register into system in early phase
during kernel boot, but the clock sources aren't probed at this point.
The system has the ARM architecture timer, so we don't need the GPT
timer from mediatek. Drop the DT node for it.
Fixes: 9cc7f0de9e ("arm64: dts: mt7622: add timer, CCI-400 and PMU nodes")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
[mb: fix commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fix this by using a 'stdout-path' property that points to the device.
Fixes: 0b6286dd96 ("arm64: dts: mt7622: add bananapi BPI-R64 board")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
No default serial console on boot.
Fix this by using a 'stdout-path' property that points to the device.
Fixes: c0d9f9ad4f ("arm64: dts: mt7622: add earlycon to mt7622-rfb1 board")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
[mb: Fix commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add support for the bananapi R64 (BPI-R64) development board from
BIPAI KEJI. Detailed hardware information for BPI-R64 which could be
found on http://wiki.banana-pi.org/Banana_Pi_BPI-R64
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fix ram size to 512 megabytes and sort nodes in alphabetical order.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a built-in bluetooth 5 support for MT7622.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add device tree entries for timer, ARM CCI-400 and its PMU.
Otherwise, we add a cortex-a53-pmu node to enable hw perfevents.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
A couple of late-merged changes that would be useful to get in this
merge window:
- Driver support for reset of audio complex on Meson platforms. The
audio driver went in this merge window, and these changes have been
in -next for a while (just not in our tree).
- Power management fixes for IOMMU on Rockchip platforms, getting
closer to kexec working on them, including Chromebooks.
- Another pass updating "arm,psci" -> "psci" for some properties that
have snuck in since last time it was done.
-----BEGIN PGP SIGNATURE-----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=dQaG
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late updates from Olof Johansson:
"A couple of late-merged changes that would be useful to get in this
merge window:
- Driver support for reset of audio complex on Meson platforms. The
audio driver went in this merge window, and these changes have been
in -next for a while (just not in our tree).
- Power management fixes for IOMMU on Rockchip platforms, getting
closer to kexec working on them, including Chromebooks.
- Another pass updating "arm,psci" -> "psci" for some properties that
have snuck in since last time it was done"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
iommu/rockchip: Move irq request past pm_runtime_enable
iommu/rockchip: Handle errors returned from PM framework
arm64: rockchip: Force CONFIG_PM on Rockchip systems
ARM: rockchip: Force CONFIG_PM on Rockchip systems
arm64: dts: Fix various entry-method properties to reflect documentation
reset: imx7: Fix always writing bits as 0
reset: meson: add meson audio arb driver
reset: meson: add dt-bindings for meson-axg audio arb
The idle-states binding documentation[1] mentions that the
'entry-method' property is required on 64-bit platforms and must be
set to "psci".
commit a13f18f59d ("Documentation: arm: Fix typo in the idle-states
bindings examples") attempted to fix this earlier but clearly more is
needed.
Fix the cpu-capacity.txt documentation that uses the incorrect value so
we don't get copy-paste errors like these. Clarify the language in
idle-states.txt by removing the reference to the psci bindings that
might be causing this confusion.
Finally, fix devicetrees of various boards to reflect current
documentation.
[1] Documentation/devicetree/bindings/arm/idle-states.txt (see
idle-states node)
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add initial device tree support for Mediatek X20 Development Board
based on MT6797 Deca core SoC. This board is one of the 96Boards
Consumer Edition platform.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The input clock of UART0 should be CLK_PERI_UART0_PD.
Fixes: 13f36c326c ("arm64: dts: mt7622: turn uart0 clock to real ones")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add earlycon to mt7622-rfb1 as to know what was going on when a certain
fault is happening at the early initialization stage.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Using gpio-ranges property represent which GPIOs correspond to which pins
on MT7622 pin controllers. For details, we can see section 2.1 of
Documentation/devicetree/bindings/gpio/gpio.txt to know how to bind pinctrl
and gpio drivers via the "gpio-ranges" property.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add EINT support to pinctrl and set those GPIO keys as interrupt-driven
keys.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add audio device nodes and its proper setup for all used pins
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds pinctrl file for mt2712.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
add mmc device nodes and proper setup for used pins
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Jimin Wang <jimin.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds SATA support fot MT7622.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds PCIe support for MT7622.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
[mb: fix type in commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
add ethernet device nodes which enable GMAC1 with SGMII interface
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
add nodes for NOR flash, parallel Nand flash with error correction code
support.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: RogerCC Lin <rogercc.lin@mediatek.com>
Cc: Guochun Mao <guochun.mao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch also cleans up two oscillators that provide clocks for MT7623.
Switch the uart clocks to the real ones while at it.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add clocks, regulators and opp information into cpu nodes.
In addition, the power supply for cpu nodes is deployed on
mt7622-rfb1 board.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable pwrap and MT6380 on mt7622-rfb1 board. Also add all mt6380
regulator nodes in an alone file to allow similar boards using MT6380
able to resue the configuration.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
[mb: add missing space]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
add pinctrl device nodes and rfb1 board, additionally include all pin
groups possible being used on rfb1 board and available gpio keys.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add clock controller nodes for MT7622 and include header for topckgen,
infracfg, pericfg, apmixedsys, ethsys, sgmiisys, pciesys and ssusbsys
for those devices nodes to be added afterwards.
In addition, provides an oscillator node for the source of PLLs and dummy
clock for PWARP to complement missing support of clock gate for the
wrapper circuit in the driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We get a moderate number of new machines this time, and only one
new SoC variant (Actions S700):
Actions:
S700 Soc and CubieBoard7 development board
Allo.com Sparky Single-board-computer
Allwinner:
Orange Pi R1 development board
Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
Axentia Nattis/Natte digital signage
sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
SolidRun Humminboard2 development board
Variscite DART-MX6 SoM and Carrier-board
Technologic TS-4600 and TS-7970 development board
Toradex Colibri iMX7D SoM board
v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
Moxa UC-8410A Series industrial computer
Gemini:
D-Link DNS-313 NAS enclosure
OMAP:
LogicPD OMAP35xx SOM-LV devkit
LogicPD OMAP35xx Torpedo devkit
Renesas:
r8a77970 (V3M) Starter Kit board
r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
Aspeed clk controller support
Freescale LS1088A, LS1021A device support
Gemini Ethernet, PCI, TVE, panel
Keystone gpio, qspi, more uarts
Mediatek cpufreq, regulator, clock, reset
Marvell thermal, cpufreq, nand
Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
Rockchip Mipi, GPU, display
Samsung Exynos5433 PMU, power domain, nfc
Spreadtrum: sc9860 clocks
Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qN1F
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"We get a moderate number of new machines this time, and only one new
SoC variant (Actions S700):
Actions:
- S700 Soc and CubieBoard7 development board
- Allo.com Sparky Single-board-computer
Allwinner:
- Orange Pi R1 development board
- Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
- Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
- Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
- Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
- Axentia Nattis/Natte digital signage
- sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
- SolidRun Humminboard2 development board
- Variscite DART-MX6 SoM and Carrier-board
- Technologic TS-4600 and TS-7970 development board
- Toradex Colibri iMX7D SoM board
- v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
- Moxa UC-8410A Series industrial computer
Gemini:
- D-Link DNS-313 NAS enclosure
OMAP:
- LogicPD OMAP35xx SOM-LV devkit
- LogicPD OMAP35xx Torpedo devkit
Renesas:
- r8a77970 (V3M) Starter Kit board
- r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
- Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
- Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
- Aspeed clk controller support
- Freescale LS1088A, LS1021A device support
- Gemini Ethernet, PCI, TVE, panel
- Keystone gpio, qspi, more uarts
- Mediatek cpufreq, regulator, clock, reset
- Marvell thermal, cpufreq, nand
- Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
- Rockchip Mipi, GPU, display
- Samsung Exynos5433 PMU, power domain, nfc
- Spreadtrum: sc9860 clocks
- Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ..."
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (690 commits)
arm64: dts: stratix10: fix SPI settings
ARM: dts: socfpga: add i2c reset signals
arm64: dts: stratix10: add USB ECC reset bit
arm64: dts: stratix10: enable USB on the devkit
ARM: dts: socfpga: disable over-current for Arria10 USB devkit
ARM: dts: Nokia N9: add support for up/down keys in the dts
ARM: dts: nomadik: add interrupt-parent for clcd
ARM: dts: Add ethernet to a bunch of platforms
ARM: dts: Add ethernet to the Gemini SoC
ARM: dts: rename oxnas dts files
ARM: dts: s5pv210: add interrupt-parent for ohci
ARM: lpc3250: fix uda1380 gpio numbers
ARM: dts: STi: Add gpio polarity for "hdmi,hpd-gpio" property
ARM: dts: dra7: Reduce shut down temperature of non-cpu thermal zones
ARM: dts: n900: Add aliases for lcd and tvout displays
ARM: dts: Update ti-sysc data for existing users
ARM: dts: Fix smartreflex compatible for omap3 shared mpu-iva instance
arm64: dts: marvell: armada-80x0: Fix pinctrl compatible string
arm: spear13xx: Fix spics gpio controller's warning
arm: spear13xx: Fix dmas cells
...
dtc complains about the lack of #coolin-cells properties for the
CPU nodes that are referred to as "cooling-device":
arch/arm64/boot/dts/mediatek/mt8173-evb.dtb: Warning (cooling_device_property): Missing property '#cooling-cells' in node /cpus/cpu@0 or bad phandle (referred from /thermal-zones/cpu_thermal/cooling-maps/map@0:cooling-device[0])
arch/arm64/boot/dts/mediatek/mt8173-evb.dtb: Warning (cooling_device_property): Missing property '#cooling-cells' in node /cpus/cpu@100 or bad phandle (referred from /thermal-zones/cpu_thermal/cooling-maps/map@1:cooling-device[0])
Apparently this property must be '<2>' to match the binding.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Use new binding about USB wakeup which now supports multi USB
wakeup glue layer between SSUSB and SPM.
Meanwhile remove dummy clocks of USB wakeup.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add opp v2 information,
and also add clocks, regulators and opp information into cpu nodes
Signed-off-by: Andrew-sh Cheng <andrew-sh.cheng@mediatek.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add clock controller nodes for MT2712, include topckgen, infracfg,
pericfg, mcucfg and apmixedsys. This patch also add six oscillators that
provide clocks for MT2712.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add opp v2 information,
and also add clocks, regulators and opp information into cpu nodes
Signed-off-by: Andrew-sh Cheng <andrew-sh.cheng@mediatek.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
We add device tree files for a couple of additional SoCs in various areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for networking,
Amlogic A113D for audio, and Renesas R-Car V3M for automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX, Amlogic
and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues that
the latest version of 'dtc' now warns about. Unfortunately there is still
a lot left to do.
A rework of the ARM foundation model introduced several new files
for common variations of the model.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TnSo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Arnd Bergmann:
"We add device tree files for a couple of additional SoCs in various
areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for
networking, Amlogic A113D for audio, and Renesas R-Car V3M for
automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX,
Amlogic and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues
that the latest version of 'dtc' now warns about. Unfortunately there
is still a lot left to do.
A rework of the ARM foundation model introduced several new files for
common variations of the model"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (599 commits)
arm64: dts: uniphier: route on-board device IRQ to GPIO controller for PXs3
dt-bindings: bus: Add documentation for the Technologic Systems NBUS
arm64: dts: actions: s900-bubblegum-96: Add fake uart5 clock
ARM: dts: owl-s500: Add CubieBoard6
dt-bindings: arm: actions: Add CubieBoard6
ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock
ARM: dts: owl-s500: Set power domains for CPU2 and CPU3
arm: dts: mt7623: remove unused compatible string for pio node
arm: dts: mt7623: update usb related nodes
arm: dts: mt7623: update crypto node
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
...
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing memory
leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node. The
prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to dtb
compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage Technology,
shimafuji, Tecon Microprocessor Technologies, DH electronics GmbH,
Opal Kelly, and Next Thing
-----BEGIN PGP SIGNATURE-----
iQItBAABCAAXBQJaCwaSEBxyb2JoQGtlcm5lbC5vcmcACgkQ+vtdtY28YcNzeA/8
C8uQhSsX2+UQZvFzcEA8KQAMGT3kYdrcf+gidRKwCEUWg1qscUEpTb3n3Rm5NUbU
RPD1s6GSlh6fJCMHDTQ6Tti/T59L7nZa2/AIGmUishGu4x4q1o18AobpFJmYP/EM
SJPwnmm5RV9WcZFao1y+sY3Xtn8DStxHO4cS+dyF5/EvPN9D8nbLJfu7bgTBAZww
HktIMB9kx+GTipRQZBvBwXoy5MJjthIZub4XwzesA4tGananj4cXlc0xaVxpdYy3
5bO6q5F7cbrZ2uyrF+oIChpCENK4VaXh80m0WHc8EzaG++shzEkR4he1vYkwnV+I
OYo4vsUg9dP8rBksUG1eYhS8fJKPvEBRNP7ETT5utVBy5I/tDEbo/crmQZRTIDIC
hZbhcdZlISZj0DzkMK2ZHQV9UYtRWzXrJbZHFIPP12GCyvXVxYJUIWb9iYnUYSon
KugygsFSpZHMWmfAhemw5/ctJZ19qhM5UIl2KZk5tMBHAf466ILmZjg0me6fYkOp
eADfwHJ1dLMdK79CVMHSfp+vArcZXp35B16c3sWpJB36Il97Mc/9siEufCL4GKX7
IBBnQBlbpSBKBejWVyI7Ip/Xp5u4qAQD+ZMJ9oLqBRqfWerHbDuOERlEOgwGqJYr
9v4HvP7V8eVUvAdqXka4EBfCyAgUzXDAxG2Dfmv9vGU=
=jgpN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
- Introduce host claiming by context to support blkmq
- Preparations for enabling CQE (eMMC CMDQ) requests
- Re-factorizations to prepare for blkmq support
- Re-factorizations to prepare for CQE support
- Fix signal voltage switch for SD cards without power cycle
- Convert RPMB to a character device
- Export eMMC revision via sysfs
- Support eMMC DT binding for fixed driver type
- Document mmc_regulator_get_supply() API
MMC host:
- omap_hsmmc: Updated regulator management for PBIAS
- sdhci-omap: Add new OMAP SDHCI driver
- meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
- sdhci-pci: Add support for Intel CDF
- sdhci-acpi: Fix voltage switch for some Intel host controllers
- sdhci-msm: Enable delay circuit calibration clocks
- sdhci-msm: Manage power IRQ properly
- mediatek: Add support of mt2701/mt2712
- mediatek: Updates management of clocks and tunings
- mediatek: Upgrade eMMC HS400 support
- rtsx_pci: Update tuning for gen3 PCI-Express
- renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
- Catch all errors when getting regulators
- Various additional improvements and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3Gvx
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Introduce host claiming by context to support blkmq
- Preparations for enabling CQE (eMMC CMDQ) requests
- Re-factorizations to prepare for blkmq support
- Re-factorizations to prepare for CQE support
- Fix signal voltage switch for SD cards without power cycle
- Convert RPMB to a character device
- Export eMMC revision via sysfs
- Support eMMC DT binding for fixed driver type
- Document mmc_regulator_get_supply() API
MMC host:
- omap_hsmmc: Updated regulator management for PBIAS
- sdhci-omap: Add new OMAP SDHCI driver
- meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
- sdhci-pci: Add support for Intel CDF
- sdhci-acpi: Fix voltage switch for some Intel host controllers
- sdhci-msm: Enable delay circuit calibration clocks
- sdhci-msm: Manage power IRQ properly
- mediatek: Add support of mt2701/mt2712
- mediatek: Updates management of clocks and tunings
- mediatek: Upgrade eMMC HS400 support
- rtsx_pci: Update tuning for gen3 PCI-Express
- renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
- Catch all errors when getting regulators
- Various additional improvements and cleanups"
* tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (91 commits)
sdhci-fujitsu: add support for setting the CMD_DAT_DELAY attribute
dt-bindings: sdhci-fujitsu: document cmd-dat-delay property
mmc: tmio: Replace msleep() of 20ms or less with usleep_range()
mmc: dw_mmc: Convert timers to use timer_setup()
mmc: dw_mmc: Cleanup the DTO timer like the CTO one
mmc: vub300: Use common code in __download_offload_pseudocode()
mmc: tmio: Use common error handling code in tmio_mmc_host_probe()
mmc: Convert timers to use timer_setup()
mmc: sdhci-acpi: Fix voltage switch for some Intel host controllers
mmc: sdhci-acpi: Let devices define their own private data
mmc: mediatek: perfer to use rise edge latching for cmd line
mmc: mediatek: improve eMMC hs400 mode read performance
mmc: mediatek: add latch-ck support
mmc: mediatek: add support of source_cg clock
mmc: mediatek: add stop_clk fix and enhance_rx support
mmc: mediatek: add busy_check support
mmc: mediatek: add async fifo and data tune support
mmc: mediatek: add pad_tune0 support
mmc: mediatek: make hs400_tune_response only for mt8173
arm64: dts: mt8173: remove "mediatek, mt8135-mmc" from mmc nodes
...
If CONFIG_OF_ALL_DTBS is enabled, "make ARCH=arm64 dtbs" compiles each
DTB twice; one from arch/arm64/boot/dts/*/Makefile and the other from
the dtb-$(CONFIG_OF_ALL_DTBS) line in arch/arm64/boot/dts/Makefile.
It could be a race problem when building DTBS in parallel.
Another minor issue is CONFIG_OF_ALL_DTBS covers only *.dts in vendor
sub-directories, so this broke when Broadcom added one more hierarchy
in arch/arm64/boot/dts/broadcom/<soc>/.
One idea to fix the issues in a clean way is to move DTB handling
to Kbuild core scripts. Makefile.dtbinst already recognizes dtb-y
natively, so it should not hurt to do so.
Add $(dtb-y) to extra-y, and $(dtb-) as well if CONFIG_OF_ALL_DTBS is
enabled. All clutter things in Makefiles go away.
As a bonus clean-up, I also removed dts-dirs. Just use subdir-y
directly to traverse sub-directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[robh: corrected BUILTIN_DTB to CONFIG_BUILTIN_DTB]
Signed-off-by: Rob Herring <robh@kernel.org>
We need to add "clean-files" in Makfiles to clean up DT blobs, but we
often miss to do so.
Since there are no source files that end with .dtb or .dtb.S, so we
can clean-up those files from the top-level Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <robh@kernel.org>
devicetree bindings has been updated to support multi-platforms,
so that each platform has its owns compatible name.
And, this compatible name may used in driver to distinguish with
other platform.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add CPU idle state nodes to enable C1/C2 idle states.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
After adding the clock subsystem to the SOC, the dummy
clock clk32k is not longer needed. Delete it.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the support for the MT7622 reference board variant 1 from
MediaTek.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
add basic nodes into the mt7622.dtsi for the system
bring-up which includes ARM CPU, GIC, timer, MediaTek
UART, SYSIRQ and one reserved memory region for ATF.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This resolves a build error in the next/dt branch:
In file included from arch/arm64/boot/dts/mediatek/mt6797-evb.dts:16:0:
arch/arm64/boot/dts/mediatek/mt6797.dtsi:15:10: fatal error: dt-bindings/power/mt6797-power.h: No such file or directory
003f5d0c34 ("arm64: dts: mediatek: add clk and scp nodes for MT6797")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mt8173:
- split USB SuperSpeed port in HighSpeed and SuperSpeed ports.
- move USB phy clocks up in hierarchy to met new bindings description
- move MDP nodes up in hierarchy to met new bindings description
mt6797:
- add basic SoC support
- add clock driver
- add power domain
dt-bindings:
- clean-up i2c binding description
- add binding for mt2701 i2c node
- add fallback compatible to scpsys binding description
- add bindings description for mt7622 and mt6796
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=H12B
-----END PGP SIGNATURE-----
Merge tag 'v4.12-next-dts64' of https://github.com/mbgg/linux-mediatek into next/dt64
Add device tree nodes for
mt8173:
- split USB SuperSpeed port in HighSpeed and SuperSpeed ports.
- move USB phy clocks up in hierarchy to met new bindings description
- move MDP nodes up in hierarchy to met new bindings description
mt6797:
- add basic SoC support
- add clock driver
- add power domain
dt-bindings:
- clean-up i2c binding description
- add binding for mt2701 i2c node
- add fallback compatible to scpsys binding description
- add bindings description for mt7622 and mt6796
* tag 'v4.12-next-dts64' of https://github.com/mbgg/linux-mediatek:
dt-bindings: mediatek: add bindings for MediaTek MT7622 SoC
arm64: dts: mt8173: Fix mdp device tree
dt-bindings: i2c: Add Mediatek MT2701 i2c binding
dt-bindings: i2c-mtk: Add mt7623 binding
dt-bindings: i2c-mtk: Delete bindings
dt-bindings: i2c-mt6577: Rename file to reflect bindings
dt-bindings: mtk-sysirq: Correct bindings for supported SoCs
arm64: dts: mediatek: add clk and scp nodes for MT6797
dt-bindings: mediatek: add MT6797 power dt-bindings
arm64: dts: mediatek: add mt6797 support
dt-bindings: mediatek: Add bindings for mediatek MT6797 Platform
arm64: dts: mt8173: move clock from phy node into port nodes
arm64: dts: mt8173: split usb SuperSpeed port into two ports
Signed-off-by: Olof Johansson <olof@lixom.net>
If the mdp_* nodes are under an mdp sub-node, their corresponding
platform device does not automatically get its iommu assigned properly.
Fix this by moving the mdp component nodes up a level such that they are
siblings of mdp and all other SoC subsystems. This also simplifies the
device tree.
Although it fixes iommu assignment issue, it also break compatibility
with old device tree. So, the patch in driver is needed to iterate over
sibling mdp device nodes, not child ones, to keep driver work properly.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Minghsiu Tsai <minghsiu.tsai@mediatek.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds basic chip support for MT6797 SoC.
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
there is a reference clock for each port, HighSpeed port is 48M,
and SuperSpeed port is usually 26M. it is flexible to move it
into port node, then unused clock can be disabled.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
split the old SuperSpeed port node into a HighSpeed one and a new
SuperSpeed one.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
ARM64 DT updates are fairly small this time, only two new SoCs and a handful
of new machines get added, all of them similar to other hardware we already
support.
New SoC:
- HiSilicon Kirin960/Hi3660 and HiKey960 development board
- NXP LS1012a with three reference boards
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A
New development board:
- Banana Pi M64, based on Allwinner A64
http://www.banana-pi.org/m64.html
- SolidRun MACCHIATOBin based on Marvell Armada 8K
https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/
- Broadcom BCM958712DxXMC NorthStar2 reference board (another one)
A lot of platforms improve support for existing machines by adding
extra devices for which a binding and driver is availabe:
Allwinner: MMC, USB
ARM Juno: Coresight, STM
Broadcom: NS2 GICv2m irqchip and PCIe
Marvell: Armada 3700 SPI, I2C, ethernet switch
Mediatek: MT8173 thermal
NXP i.MX: LS1046A thermal
Qualcomm: coresight on MSM8916, HDMI, WCNSS, SCM
Renesas: r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd
Rockchip: thermal, eDP, pinctrl enhancements
Samsung: TM2 touchkey, Exynos5433 HDMI and power management improvements
UniPhier: SD reset, eMMC controller
ZTE: oppv2 cpufreq
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=glug
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"ARM64 DT updates are fairly small this time, only two new SoCs and a
handful of new machines get added, all of them similar to other
hardware we already support.
New SoC:
- HiSilicon Kirin960/Hi3660 and HiKey960 development board
- NXP LS1012a with three reference boards:
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A
New development board:
- Banana Pi M64, based on Allwinner A64:
http://www.banana-pi.org/m64.html
- SolidRun MACCHIATOBin based on Marvell Armada 8K:
https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/
- Broadcom BCM958712DxXMC NorthStar2 reference board (another one)
A lot of platforms improve support for existing machines by adding
extra devices for which a binding and driver is availabe:
Allwinner:
- MMC, USB
ARM Juno:
- Coresight, STM
Broadcom:
- NS2 GICv2m irqchip and PCIe
Marvell:
- Armada 3700 SPI, I2C, ethernet switch
Mediatek:
- MT8173 thermal
NXP i.MX:
- LS1046A thermal
Qualcomm:
- coresight on MSM8916, HDMI, WCNSS, SCM
Renesas:
- r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd
Rockchip:
- thermal, eDP, pinctrl enhancements
Samsung:
- TM2 touchkey, Exynos5433 HDMI and power management improvements
UniPhier:
- SD reset, eMMC controller
ZTE:
- oppv2 cpufreq"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (110 commits)
arm64: dts: qcom: Add msm8916 CoreSight components
arm64: dts: marvell: adjust name of sd-mmc-gop clock in syscon
arm64: allwinner: add BananaPi-M64 support
arm64: allwinner: a64: add UART1 pin nodes
arm64: allwinner: pine64: add MMC support
arm64: allwinner: a64: Increase the MMC max frequency
arm64: allwinner: a64: Add MMC pinctrl nodes
arm64: allwinner: a64: Add MMC nodes
dt-bindings: clockgen: Add compatible string for LS1012A
Documentation: DT: add LS1012A compatible for SCFG and DCFG
Documentation: DT: Add entry for FSL LS1012A RDB, FRDM, QDS boards
arm64: dts: marvell: add generic-ahci compatibles for CP110 ahci
arm64: tegra: Use symbolic reset identifiers
arm64: dts: r8a7796: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: tidyup audma definition order
arm64: dts: r8a7796: Link ARM GIC to clock and clock domain
arm64: dts: r8a7795: Link ARM GIC to clock and clock domain
arm64: dts: r8a7796: Add R-Car Gen3 thermal support
arm64: dts: r8a7795: Add R-Car Gen3 thermal support
...
Due to the reference clock comes from 26M oscillator directly
on mt8173, and it is a fixed-clock in DTS which always turned
on, we ignore it before. But on some platforms, it comes
from PLL, and need be controlled, so here add it, no matter
it is a fixed-clock or not.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to [0], the contribution field for each cooling-device express
their relative power efficiency. Higher weights express higher power
efficiency. Weighting is relative such that if each cooling device has a
weight of 1 they are considered equal. This is particularly useful in
heterogeneous systems where two cooling devices may perform the same kind
of compute, but with different efficiency.
[0] Documentation/thermal/power_allocator.txt
According to Mediatek IC designer, the power efficiency ratio between the
LITTLE core cluster (cooling-device cpu0) and big core cluster
(cooling-device cpu1) is around 3:1 (3072:1024).
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
To support HDMI 4K resolution, mmsys need clcok
mm_sel to be 400MHz.
The board .dts file should override the clock rate
property with the higher VENCPLL frequency the board
supports HDMI 4K resolution.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
-----BEGIN PGP SIGNATURE-----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=ADpU
-----END PGP SIGNATURE-----
Merge tag 'media/v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new Mediatek drivers: mtk-mdp and mtk-vcodec
- some additions at the media documentation
- the CEC core and drivers were promoted from staging to mainstream
- some cleanups at the DVB core
- the LIRC serial driver got promoted from staging to mainstream
- added a driver for Renesas R-Car FDP1 driver
- add DVBv5 statistics support to mn88473 driver
- several fixes related to printk continuation lines
- add support for HSV encoding formats
- lots of other cleanups, fixups and driver improvements.
* tag 'media/v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (496 commits)
[media] v4l: tvp5150: Add missing break in set control handler
[media] v4l: tvp5150: Don't inline the tvp5150_selmux() function
[media] v4l: tvp5150: Compile tvp5150_link_setup out if !CONFIG_MEDIA_CONTROLLER
[media] em28xx: don't store usb_device at struct em28xx
[media] em28xx: use usb_interface for dev_foo() calls
[media] em28xx: don't change the device's name
[media] mn88472: fix chip id check on probe
[media] mn88473: fix chip id check on probe
[media] lirc: fix error paths in lirc_cdev_add()
[media] s5p-mfc: Add support for MFC v8 available in Exynos 5433 SoCs
[media] s5p-mfc: Rework clock handling
[media] s5p-mfc: Don't keep clock prepared all the time
[media] s5p-mfc: Kill all IS_ERR_OR_NULL in clocks management code
[media] s5p-mfc: Remove dead conditional code
[media] s5p-mfc: Ensure that clock is disabled before turning power off
[media] s5p-mfc: Remove special clock rate management
[media] s5p-mfc: Use printk_ratelimited for reporting ioctl errors
[media] s5p-mfc: Set DMA_ATTR_ALLOC_SINGLE_PAGES
[media] vivid: Set color_enc on HSV formats
[media] v4l2-tpg: Init hv_enc field with a valid value
...
Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where things
come together.
We get a DT descriptions for a couple of new SoCs, all of them variants
of other chips we already support, and usually coming with a new
evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers
or industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on
Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it into
products and have served their purpose in the kernel as a template
for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree
Conflicts:
arch/arm/boot/dts/r8a*.dtsi: a node was added
the clk tree, keep both sides and watch out for git
dropping the required '};' at the end of each side.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wJt3
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where
things come together.
We get a DT descriptions for a couple of new SoCs, all of them
variants of other chips we already support, and usually coming with a
new evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers or
industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it
into products and have served their purpose in the kernel as a
template for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (422 commits)
arm: dts: zynq: Add MicroZed board support
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: artpec: add pcie support
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
ARM: dts: berlin2q-marvell-dmp: fix regulators' name
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM: dts: r8a7794: Add device node for PRR
ARM: dts: r8a7793: Add device node for PRR
ARM: dts: r8a7792: Add device node for PRR
ARM: dts: r8a7791: Add device node for PRR
ARM: dts: r8a7790: Add device node for PRR
ARM: dts: r8a7779: Add device node for PRR
ARM: dts: r8a73a4: Add device node for PRR
ARM: dts: sk-rzg1e: add Ether support
ARM: dts: sk-rzg1e: initial device tree
...
The devicetree node for mt8173-auxadc lacks the clock and
io-channel-cells property. This leads to a non-working driver.
mt6577-auxadc 11001000.auxadc: failed to get auxadc clock
mt6577-auxadc: probe of 11001000.auxadc failed with error -2
Fix these fields to get the device up and running.
Fixes: 748c7d4de4 ("ARM64: dts: mt8173: Add thermal/auxadc device
nodes")
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add video decoder node for MT8173
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add an HDMI connector node and enable the devices that are part of the
HDMI display path: cec, dpi0, hdmi_phy, and hdmi0.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds the device nodes for the HDMI encoder, HDMI PHY,
and HDMI CEC modules.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Cawa Cheng <cawa.cheng@mediatek.com>
Signed-off-by: Jie Qiu <jie.qiu@mediatek.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add video encoder node for MT8173
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds basic chip support for MT6755 SoC.
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds the device nodes for the DISP function blocks
comprising the display subsystem.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Cawa Cheng <cawa.cheng@mediatek.com>
Signed-off-by: Jie Qiu <jie.qiu@mediatek.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds the thermal controller and auxadc nodes to the Mediatek MT8173
dtsi file.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This time with:
* Updates for the Exynos IOMMU driver to make use of default
domains and to add support for the SYSMMU v5
* New Mediatek IOMMU driver
* Support for the ARMv7 short descriptor format in the
io-pgtable code
* Default domain support for the ARM SMMU
* Couple of other small fixes all over the place
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=uiAk
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- updates for the Exynos IOMMU driver to make use of default domains
and to add support for the SYSMMU v5
- new Mediatek IOMMU driver
- support for the ARMv7 short descriptor format in the io-pgtable code
- default domain support for the ARM SMMU
- couple of other small fixes all over the place
* tag 'iommu-updates-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (41 commits)
iommu/ipmmu-vmsa: Add r8a7795 DT binding
iommu/mediatek: Check for NULL instead of IS_ERR()
iommu/io-pgtable-armv7s: Fix kmem_cache_alloc() flags
iommu/mediatek: Fix handling of of_count_phandle_with_args result
iommu/dma: Fix NEED_SG_DMA_LENGTH dependency
iommu/mediatek: Mark PM functions as __maybe_unused
iommu/mediatek: Select ARM_DMA_USE_IOMMU
iommu/exynos: Use proper readl/writel register interface
iommu/exynos: Pointers are nto physical addresses
dts: mt8173: Add iommu/smi nodes for mt8173
iommu/mediatek: Add mt8173 IOMMU driver
memory: mediatek: Add SMI driver
dt-bindings: mediatek: Add smi dts binding
dt-bindings: iommu: Add binding for mediatek IOMMU
iommu/ipmmu-vmsa: Use ARCH_RENESAS
iommu/exynos: Support multiple attach_device calls
iommu/exynos: Add Maintainers entry for Exynos SYSMMU driver
iommu/exynos: Add support for v5 SYSMMU
iommu/exynos: Update device tree documentation
iommu/exynos: Add support for SYSMMU controller with bogus version reg
...
This patch add the iommu/larbs nodes for mt8173
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
MT8173 E1 chip has one bug that if turn off USB power domain, vcore
power will also be off, thus cause modules using vcore power domain
fail, like MMC. The E1 chip only found on MT8173-evb board and this
board only has E1 chip, so implement this as a board specific
workaround.
Pwrapper use vcore power, so add pwrapper using USB power domain to
keep USB power domain not to zero and disabled.
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This is the first release where we split up the 64-bit contributions a
bit more, and in particular we are having a separate DT branch for them.
Contents:
- New devices added to Broadcom NorthStar2
- Misc fixes for Exynos7 boards
- QCOM updates for MSM8916
- Rockchip tweaks for rk3368 SoC and eval board
- A series of fixes for APM X-Gene v1 and v2
- Renesas R8A7795 CPU/PSCI additions
- Marvell Berlin4CT PSCI, cpuidle, watchdog portions
- Freescale LS1043a SoC and dev board support
+ some treewide or other misc changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWnr//AAoJEIwa5zzehBx35r0P/jyMtxtcXn9v9Tsdcenu91B/
wLVUHuVUtTQMq8nBHp3NUjFFPi51B7pKYT3uaPOE+r9TjHrwDgFP5rNVJwD3Jyn3
BTmGTM/4HNPTc+eLFk7yn0j/4xR6Njwf7DI5tjK4Xq6UC+xVk7v7Gy0dOcLPGUs4
x5hxSGSY6ncgEpABnK/w+GhxNfc6ua8TM3T7ZK9VeA9aZXFdp8lCWBGj4TyTT1By
m2E/uwzhFeN2PQ4MLDI3MvDQoGWsOcsDLTB0oltdCSRdJoGn3Zbl+xG9/tMZTDiy
pa8ItMb7VmQQdS/WNgAT3obgqvcfelSNvFaVWoLfjamb0bPVaz55bM+IjTqHr5kE
ZjdDMq1kP4DdIPIFHs/4cmSkG7OUf+PO4/2BzqzroKCgZPXZX9NRr3aDQQYAzLlr
yLUAGkY5O1cGP8CXP1zFZTiHjEmbCFX3XOpi6obTnyElxxxX3LDFsqrRSmFs41HF
V7AKraWoEZ1GWWycRMC8SRo/OuEgx6aCRzNVR+0NwLk6AP6Kdxsb9naq3I2wfS5L
+9KnNN7nNhRYMP0L53aMEhYrxkajeUrO3a8JbfowBlCwXlvLBPysGu11yWvI8flG
9SLK/TMmsa1Yk+XDjjVSHn8BKsYI1iCGnrxXjb2ZYNimqSPliMNxGr8lKvJ1L1Bz
ELq+CpJizQ4tzuJpk6xv
=f4yG
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Olof Johansson:
"This is the first release where we split up the 64-bit contributions a
bit more, and in particular we are having a separate DT branch for
them.
Contents:
- New devices added to Broadcom NorthStar2
- Misc fixes for Exynos7 boards
- QCOM updates for MSM8916
- Rockchip tweaks for rk3368 SoC and eval board
- A series of fixes for APM X-Gene v1 and v2
- Renesas R8A7795 CPU/PSCI additions
- Marvell Berlin4CT PSCI, cpuidle, watchdog portions
- Freescale LS1043a SoC and dev board support
+ some treewide or other misc changes"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (104 commits)
dts/ls2080a: Update DTSI to add support of SP805 WDT
Documentation: DT: Add entry for ARM SP805-WDT
arm64: dts: X-Gene v2: I2C1 clock is always on
arm64: dts: X-Gene v1: I2C0 clock is always on
arm64: dts: Fix to use standard DT node names for X-Gene 1 and X-Gene 2 platforms
arm64: dts: hikey: add label properties to UARTs
arm64: dts: apq8016-sbc: add label properties for UART, I2C, and SPI
arm64: dts: apq8016-sbc: enable UART0 on LS connector
arm64: dts: juno: Add idle-states to device tree
arm64: dts: Added syscon-reboot node for FSL's LS2080A SoC
arm64: dts: add LS1043a-RDB board support
arm64: dts: add Freescale LS1043a SoC support
Documentation: DT: Add entry for Freescale LS1043a-RDB board
arm64: dts: uniphier: add PH1-LD10 SoC/board support
arm64: renesas: r8a7795: fix SATA clock assignment
arm64: dts: salvator-x: Enable SATA controller
arm64: dts: r8a7795: Add SATA controller node
arm64: renesas: r8a7795: add internal delay for i2c IPs
arm64: renesas: salvator-x: Add board part number to DT bindings
arm64: dts: r8a7795: Add pmu device nodes
...
As usual, the bulk of this release is again DT file contents.
There's a huge number of changes here, and it's challenging to give a crisp
overview of just what is in here. To start with:
New boards:
- TI-based DM3730 from LogicPD (Torpedo)
- Cosmic+ M4 (nommu) initial support (Freescale Vybrid)
- Raspberry Pi 2 DT files
- Watchdog on Meson8b
- Veyron-mickey (ASUS Chromebit) DTS
- Rockchip rk3228 SoC and eval board
- Sigma Designs Tango4
Improvements:
- Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files
- Misc new devices for Rockchip rk3036 and rk3288
- Allwinner updates for misc SoCs and systems
... and a _large_ number of other changes across the field. Devices
added to SoC DTSI and board DTS files for a number of SoC vendors, new
product boards on already-supported SoCs, cleanups and refactorings of
existing DTS/DTSI files and a bunch of other changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XDLa
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, the bulk of this release is again DT file contents.
There's a huge number of changes here, and it's challenging to give a
crisp overview of just what is in here. To start with:
New boards:
- TI-based DM3730 from LogicPD (Torpedo)
- Cosmic+ M4 (nommu) initial support (Freescale Vybrid)
- Raspberry Pi 2 DT files
- Watchdog on Meson8b
- Veyron-mickey (ASUS Chromebit) DTS
- Rockchip rk3228 SoC and eval board
- Sigma Designs Tango4
Improvements:
- Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files
- Misc new devices for Rockchip rk3036 and rk3288
- Allwinner updates for misc SoCs and systems
... and a _large_ number of other changes across the field. Devices
added to SoC DTSI and board DTS files for a number of SoC vendors, new
product boards on already-supported SoCs, cleanups and refactorings of
existing DTS/DTSI files and a bunch of other changes"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (469 commits)
ARM: dts: compulab: add new board description
ARM: versatile: add the syscon LEDs to the DT
dts: vt8500: Fix errors in SDHC node for WM8505
ARM: dts: imx6q: clean up unused ipu2grp
ARM: dts: silk: Add compatible property to "partitions" node
ARM: dts: gose: Add compatible property to "partitions" node
ARM: dts: porter: Add compatible property to "partitions" node
ARM: dts: koelsch: Add compatible property to "partitions" node
ARM: dts: lager: Add compatible property to "partitions" node
ARM: dts: bockw: Add compatible property to "partitions" node
ARM: dts: meson8b: Add watchdog node
Documentation: watchdog: Add new bindings for meson8b
ARM: meson: Add status LED for Odroid-C1
ARM: dts: uniphier: fix a typo in comment block
ARM: bcm2835: Add the auxiliary clocks to the device tree.
ARM: bcm2835: Add devicetree for bcm2836 and Raspberry Pi 2 B
ARM: bcm2835: Move the CPU/peripheral include out of common RPi DT.
ARM: bcm2835: Split the DT for peripherals from the DT for the CPU
ARM: realview: set up cache correctly on the PB11MPCore
ARM: dts: Unify G2D device node with other devices on exynos4
...
By popular vote, the DT binding includes for reset controllers are located
in include/dt-bindings/reset/. Move the mediatek reset constants in there,
too, to avoid confusion.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds psci comatible properties to support all mandatory
functions of PSCI-1.0, PSCI-0.2 and PSCI-0.1, and system suspend
can be supported in PSCI-1.0.
Signed-off-by: Fan Chen <fan.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add spi DTS node to the mt8173 and mt8173-evb.
Add dts nodes for the subsystem clocks on mt8173.
This includes mmsys, imgsys, vdecsys, vencsys, vencltsys.
Add clock nodes to the scpsys binding, which are needed to
access the registers of venc and venc_lt power domains.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=laqA
-----END PGP SIGNATURE-----
Merge tag 'v4.3-next-arm64' of https://github.com/mbgg/linux-mediatek into next/arm64
Correct i2c DTS node names in mt8173.dtsi.
Add spi DTS node to the mt8173 and mt8173-evb.
Add dts nodes for the subsystem clocks on mt8173.
This includes mmsys, imgsys, vdecsys, vencsys, vencltsys.
Add clock nodes to the scpsys binding, which are needed to
access the registers of venc and venc_lt power domains.
* tag 'v4.3-next-arm64' of https://github.com/mbgg/linux-mediatek:
arm64: dts: mt8173: Add clocks for SCPSYS unit
arm64: dts: mt8173: Add subsystem clock controller device nodes
arm64: dts: Add spi bus dts
arm64: mt8173.dtsi: correct i2c node names
Signed-off-by: Olof Johansson <olof@lixom.net>
Add clocks needed by Mediatek VENC and VENC_LT power domianis.
These clocks were needed by accessing subsystem's registers,
so they need to be enabled before power on these subsystems.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds MT8173 spi bus controllers into device tree.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Reviewed-and-Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Node name in device tree should describe general class of the
device. Correct incorrect i2c node names.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The idle-states bindings mandate that the entry-method string
in the idle-states node must be "psci" for ARM v8 64-bit systems,
but the examples in the bindings report a wrong entry-method string.
Owing to this typo, some dts in the kernel wrongly defined the
entry-method property, since they likely cut and pasted the example
definition without paying attention to the bindings definitions.
This patch fixes the typo in the DT idle states bindings examples and
respective dts in the kernel so that the bindings and related dts
files are made compliant.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Howard Chen <howard.chen@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rob Herring <robh@kernel.org>
This patch adds support SMP on MediaTek MT6795 Cortex-A53 Octa-core SoC.
Signed-off-by: Scott Shu <scott.shu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds basic chip support for MT6795 SoC
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds afe (audio front end) device node to the MT8173 dtsi file.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The MT8173 eval board contains a MT6397 PMIC. This adds the
corresponding device node to the dts file.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a DA9211 dual-channel BUCK regulator to i2c1.
This regulator supplies GPU and DVFS1 voltages.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds an idle-states node to describe the mt8173 idle states and
also adds references to the idle-states node in all CPU nodes.
Signed-off-by: Howard Chen <howard.chen@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds the SCPSYS device node to the MT8173 dtsi file.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add MT8173 I2C device nodes, include I2C controllers and pins.
MT8173 has six I2C controllers, from i2c0 to i2c6, exclude i2c5.
The 6th I2C controller register base doesn't next to 5th I2C,
and there is a hardware between 5th and 6th I2C controller. So
SoC designer name 6th controller as "i2c6", not "i2c5".
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds the device node for the PMIC wrapper.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
We used to use a fixed rate clock for the UARTs. Now that we have clock
support we can associate the correct clocks to the UARTs and drop the
26MHz fixed rate UART clock.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds the device nodes providing clocks on the Mediatek MT8173.
These are: topckgen, infracfg, pericfg and apmixedsys. These are
fed by two oscillators also added by this patch.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
As usual, quite a few device-tree updates in ARM land. There was ome
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33, Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey
Conflicts: None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wWIc
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Kevin Hilman:
"As usual, quite a few device-tree updates in ARM land. There was one
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS
RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill
SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33,
Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (462 commits)
ARM: hisi: revert changes from hisi/hip04-dt branch
ARM: nomadik: set proper compatible for accelerometer
ARM64: juno: add GPIO keys
ARM: at91/dt: sama5d4: fix dma conf for aes, sha and tdes nodes
ARM: dts: Introduce STM32F429 MCU
ARM: socfpga: dts: enable ethernet for Arria10 devkit
ARM: dts: k2l: fix the netcp range size
ARM: dts: k2e: fix the netcp range size
ARM: dts: k2hk: fix the netcp range size
ARM: dts: k2l-evm: Add device bindings for netcp driver
ARM: dts: k2e-evm: Add device bindings for netcp driver
ARM: dts: k2hk-evm: Add device bindings for netcp driver
ARM: BCM5301X: Add DT for Asus RT-AC87U
ARM: BCM5301X: add IRQ numbers for PCIe controller
ARM: BCM5301X: add NAND flash chip description
arm64: dts: Add dts files for Hisilicon Hi6220 SoC
clk: hi6220: Document devicetree bindings for hi6220 clock
arm64: hi6220: Document devicetree bindings for Hisilicon hi6220 SoC
ARM: at91/dt: sama5d4ek: mci0 uses slot 0
ARM: at91/dt: kizbox: fix mismatch LED PWM device
...
Model name in mt8173-evb.dts doesn't follow dts convention (it should
be human readable model name). Fix it.
Fixes: b3a3724841 ("arm64: dts: Add mediatek MT8173 SoC and evaluation board dts and Makefile")
Cc: <stable@vger.kernel.org> # v4.0+
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fix indentation nits to make mt8173.dtsi more consistent.
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The 8173 pinctrl node doesn't follow dts convention. Fix them.
Also add a comment to explain pinctrl register usage to make it
more clear.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add device tree support for MT8173 SoC and evaluation board based on it.
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Acked-by: Arnd Bergmann <arnd at arndb.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
