In preparation for introducing the Genio 510 EVK board support, split
mt8390-genio-700-evk.dts file in two to create mt8390-genio-common.dtsi
file, containing common definitions for both boards.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Link: https://lore.kernel.org/r/20250206-dts_mt8370-genio-510-v3-3-5ca5c3257a4c@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Describe all the components to get sound output working on the two audio
jacks, Earphone and Speaker, present on the Genio 700 EVK board with the
audio DSP enabled.
Co-developed-by: Aary Patil <aary.patil@mediatek.com>
Signed-off-by: Aary Patil <aary.patil@mediatek.com>
Co-developed-by: Suhrid Subramaniam <suhrid.subramaniam@mediatek.com>
Signed-off-by: Suhrid Subramaniam <suhrid.subramaniam@mediatek.com>
Co-developed-by: parkeryang <Parker.Yang@mediatek.com>
Signed-off-by: parkeryang <Parker.Yang@mediatek.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20241210-genio700-audio-output-v2-2-c50886ae0be2@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Enable ethernet on the Genio 700 EVK board. It has been tested to work
with speeds up to 1000Mbps.
[Cleaned up to pass dtbs_check, follow DTS style guidelines, and split
between mt8188 and genio700 commits, and addressed further feedback from
the mailing list]
Signed-off-by: Jianguo Zhang <jianguo.zhang@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Hsuan-Yu Lin <shane.lin@canonical.com>
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Signed-off-by: fanyi zhang <fanyi.zhang@mediatek.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20241018-genio700-eth-v2-2-f3c73b85507b@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Update regulator names to match schematics, replacing generic terms.
1. Add system wide 'reg_vsys' node for 4.2V power rail.
2. Add 'reg_vsys' node as 'vin-supply' for the following nodes
- common_fixed_5v, edp_panel_fixed_3v3, gpio_fixed_3v3, sdio_fixed_3v3,
touch0_fixed_3v3, usb_hub_fixed_3v3, usb_p0_vbus, and usb_p1_vbus.
3. Update regulator names according to the stable output name on
schematics.
- vdd_5v, vedp_3v3, ext_3v3, vio18_conn, wifi_3v3, vio33_tp1, vhub_3v3,
vbus_p0, vbus_p1.
- vcn18_pmu, vcn33_2_pmu, dvdd_proc_l, dvdd_core, vpa_pmu, dvdd_adsp,
va12_abb2_pmu, vsim1_pmu, vufs18_pmu.
4. Remove usb_hub_reset_1v8. Use 'hub' node to probe USB HUB
in subsequent patches.
Suggested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20241007090244.1731-1-macpaul.lin@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Enable PCIE, PCIEPHY and related Pinctrls for mt8390-genio-700-evk
board.
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20241007100749.6657-1-macpaul.lin@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Configure GPU regulator supplies and enable GPU for GENIO 700 EVK.
The GPU in MT8390 & MT8188 has two power inputs: "DVDD_GPU" and
"DVDD_SRAM_GPU". In Genio 700 EVK, DVDD_GPU is supplied by
mt6359_vproc2_buck_reg, and DVDD_SRAM_GPU is supplied by
mt6359_vsram_others_ldo_reg.
According to section 5.2 "Recommended Operating Conditions" in
MT8390 IoT Application Processor Datasheet v1.9, The recommended
operating voltage ranges are:
- DVDD_GPU: min 0.55V, max 0.86V, typical 0.75V
- DVDD_SRAM_GPU: min 0.71V, max 0.92V, typical 0.85V
To further optimize power saving, we couple DVDD_SRAM_GPU to
DVDD_GPU according to the following relation:
- For opp-880000000 or lower frequency, keep 0.75V
- For opp-915000000 and higher, DVDD_SRAM_GPU should follow
DVDD_GPU. The exact voltage for DVDD_GPU should be decided by
speed binning.
This rule is derived from the OPP table in the link.
In addition, set the voltage spread to 6250 uV, the step size of
'ldo_vsram_others' regulator of mt6359, otherwise the regulator
set_voltage operation fails.
Link: eedd6aedd4/recipes-kernel/dtbo/mt8390/gpu-mali.dts
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20241002022138.29241-7-pablo.sun@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
On some devicetrees, the drive-strength property gets assigned a
MTK_DRIVE_(x)_mA definition, which matches with (x).
For example, MTK_DRIVE_8mA equals to 8 and MTK_DRIVE_30mA equals
to 30.
Also keeping in mind that the drive-strength property is, by
(binding) definition, taking a number in milliamperes unit,
change all devicetrees to avoid the usage of any MTK_DRIVE_(x)
definition.
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240620101656.1096374-2-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add basic device-tree for the Genio 700 EVK board. The
Genio 700 EVK is based on MediaTek MT8390 SoC.
MT8390 hardware register maps are identical to MT8188.
The Genio 700 EVK has following features:
- MT8390 SoC
- MT6365 PMIC
- MT6319 Buck IC
- 12V DC Jack
- 2x4GB LPDDR4X
- 64GB eMMC 5.1
- 64Mb SPI NOR
- M.2 Key A-E slot with PCIe Gen2 and USB 2.0
- 2x DSI LCM ports
- 2x touch sensor ports
- 2x MIPI-CSI, as camera daughter board slots
- USB 2 micro USB connector
- USB 3 with 1 to 2 hub:
- M.2 Key B slot
- Type-C connector, with DisplayPort over Type-C
- HDMI 2.0 TX port with Type A HDMI connector
- eDP port
- Gigabit Ethernet with RJ45 connector
- SD card slot
- Earphone Jack
- Analog Microphone
- 2x Digital Microphone
- 3x UART with serial-to-usb converters and micro USB connectors
Signed-off-by: Chris-QJ Chen <chris-qj.chen@mediatek.com>
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230915081212.13959-2-macpaul.lin@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
