GPIOs 34 and 35 on MT8195 are of type MTK_PULL_PU_PD_RSEL_TYPE, meaning
not only can they be configured as pull-up or pull-down, but the pull
resistance can also be configured.
The current bias setting however doesn't specify a resistance value,
resulting on the following errors:
mt8195-pinctrl 10005000.pinctrl: Not support rsel value 1 Ohm for pin = 34 (GPIO34)
mt8195-pinctrl 10005000.pinctrl: Not support rsel value 1 Ohm for pin = 35 (GPIO35)
Specify the pull resistance for those GPIOs to fix the errors.
Fixes: 5bf7dabe40 ("arm64: dts: mediatek: cherry: Document gpios and add default pin config")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240531-tomato-rsel-gpio34-35-fix-v1-1-64ab2545f182@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The external output reset signal was originally disabled and sent from
firmware. However, an unfixed bug in the firmware on tomato prevents
the signal from being sent, causing the device to fail to boot. To fix
this, enable external output reset signal to allow the device to reboot
normally.
Fixes: 5eb2e303ec ("arm64: dts: mediatek: Introduce MT8195 Cherry platform's Tomato")
Signed-off-by: Hsin-Te Yuan <yuanhsinte@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240124-send-upstream-v3-1-5097c9862a73@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The entire Cherry family has two digital microphones, for which
we use the generic dmic-codec, linked to the MT6359 PMIC.
Moreover, it uses a Realtek RT1019p amplifier for the speakers
and has either a Realtek RT5682i or RT5682s audio codec on I2C2:
specifically, RT5682i is found on Tomato's rev 1 and rev 2 boards,
while RT5682s is found in rev3 and rev4 boards.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220922094908.41623-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This platform carries a HID compatible I2C touchscreen on the i2c4 bus,
but it may be at a different address, depending on the board model.
Add the node for a touchscreen at 0x10, but enable it only in the
final board dts.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-12-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add gpio-line-names to document GPIO names and add the default basic
pin configuration to allow lower power operation by setting appropriate
state on the unused pins.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-7-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Introduce the MT8195 Cherry Chromebook platform, including three
revisions of Cherry Tomato boards.
This basic configuration allows to boot Linux on all board revisions
and get a serial console from a ramdisk.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
