This adds pinctrl node for the GPIO to be used as SPI chip select 1.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Update Aramda 7k/8k DTs to use the phy-supply property of the (recent)
generic PHY framework instead of the (legacy) usb-phy preperty. Both
enable the supply when the PHY is enabled.
The COMPHY nodes only provide SERDES lanes configuration. The power
supply that is represented by the phy-supply property is just a
regulator wired to the USB connector, hence the creation of connector
nodes as child of the COMPHY nodes and the supply attached to it.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Fill-in the missing PCIe phys/phy-names DT properties of Armada 7k/8k
based boards.
The MacchiatoBin is a bit particular as the Armada8k-PCI IP supports
x4 link widths and in this case the PHY for each lane must be
referenced.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Fill-in the missing USB3 phys/phy-names DT properties of Armada 7k/8k
based boards. Only update nodes actually enabling USB3 in the default
(mainline) configuration. A few USB nodes are enabled but there is
only USB2 working on them.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Fill-in the missing SATA phys/phy-names DT properties of Armada 7k/8k
based boards.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This adds the rWTM BIU mailbox node for communication with the secure
processor. The driver already exists in
drivers/mailbox/armada-37xx-rwtm-mailbox.c.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The GPIO interrupt controllers are missing their required
specified in DT.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Armada 7040-db USB ports deliver 500mA by default while they
could deliver up to 900mA (usually, for USB3 devices).
The board embeds a GPIO controlled regulator on each port which can be
configured to deliver each amount of current.
Add a vin-supply property to the USB3 Vbus nodes for this purpose. The
regulator will be automatically 'enabled', ie. set to limit at 900mA
instead of 500mA.
Suggested-by: Alex Leibovich <alexl@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The manufacturer of this board, ships it with various SPI NOR chips and
increments U-Boot bootloader version along the time. There is no way to
tell which is placed on the board since no revision bump takes place.
This creates two issues.
The first, cosmetic. Since the NOR chip may differ, there's message on
boot stating that kernel expected w25q32dw and found different one. To
correct this, remove optional device-specific compatible string. Being
here lets replace bogus "spi-flash" compatible string with proper one.
The second is linked to partitions layout, it changed after commit:
81e7251252 ("arm64: mvebu: config: move env to the end of the 4MB boot
device") in Marvells downstream U-Boot fork [1], shifting environment
location to the end of boot device. Since the new boards will have U-Boot
with this change, it'll lead to improper results writing or reading from
these partitions. We can't tell if users will update bootloader to recent
version provided on manufacturer website, so lets drop partitons layout.
1. https://github.com/MarvellEmbeddedProcessors/u-boot-marvell.git
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
While AP I2C bus was available to users in early revisions of the SoC,
this is not the case anymore since eMMC was connected to the AP. Most
users do not have access to this I2C bus so do not enable it in the
board device tree.
As there are three I2C buses enabled on this board, add an alias to be
sure the two other buses keep their initial numbering.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
[<miquel.raynal@bootlin.com>: Reword commit message, add alias]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Avoid critical temperatures in the AP806 by adding the relevant trip
points/cooling-maps using CPUfreq as cooling device.
So far, when the temperature reaches 100°C in the thermal IP of the
AP806 (close enough from the 2/4 cores) an overheat interrupt is
raised. The thermal core then shutdowns the system to avoid damaging
the hardware.
Adding CPUfreq as a cooling device could help avoiding such very
critical situation. For that, we enable thermal throttling by
defining, for each CPU, two trip points with the corresponding cooling
'intensity'. CPU0 and CPU1 are in the same cluster and are driven by
the same clock. Same applies for CPU2 and CPU3, if available. So
changing the frequency of one will also change the frequency of the
other one, hence the use of two cooling devices per core.
The heat map is as follow:
- Below 85°C: the cluster runs at the highest frequency
(e.g: 1200MHz).
- Between 85°C and 95°C: there are two trip points at half
(e.g: 600MHz) and a third (e.g: 400MHz) of the highest frequency.
- Above 95°C the cluster runs at a quarter of the highest frequency
(e.g: 300MHz).
- At 100°C the platform is shutdown.
Suggested-by: Omri Itach <omrii@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
When adding thermal nodes, the CPUs have been named from 1 to 4 while
usually everywhere else they are referred as 0-3. Let's change this to
be consistent with later changes when we will use CPUfreq and CPU
phandles as cooling devices to avoid inconsistencies in the nodes
numbering.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The Clearfog GT-8K board is capable of supplying power up to 2W to SFP
modules. Make that explicit in the device-tree. Without this property
current kernel does not allow SFP modules that require more than 1W.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Running a graphics adapter on the MACCHIATObin fails due to an
insufficiently sized memory window.
Enlarge the memory window for the PCIe slot to 512 MiB.
With the patch I am able to use a GT710 graphics adapter with 1 GB onboard
memory.
These are the mapped memory areas that the graphics adapter is actually
using:
Region 0: Memory at cc000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (64-bit, prefetchable) [size=128M]
Region 3: Memory at c8000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at 1000 [size=128]
Expansion ROM at ca000000 [disabled] [size=512K]
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
There is currently no DT binding for GPIO rfkill signals. To make
mini-PCIe attached WiFi devices work, use gpio-hog to hold the
wlan_disable signal de-asserted.
Signed-off-by: Thomas Schreiber <tschreibe@gmail.com>
[baruch: add pinctrl node; rename tag]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This is a smaller update than the past few times, but with just over
500 non-merge changesets still dwarfes the rest of the SoC tree.
Three new SoC platforms get added, each one a follow-up to an existing
product, and added here in combination with a reference platform:
- Renesas RZ/A2M (R7S9210) 32-bit Cortex-A9 Real-time imaging processor
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rza/rza2m.html
- Renesas RZ/G2E (r8a774c0) 64-bit Cortex-A53 SoC "for
Rich Graphics Applications".
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg2e.html
- NXP i.MX8QuadXPlus 64-bit Cortex-A35 SoC
https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/i.mx-applications-processors/i.mx-8-processors/i.mx-8x-family-arm-cortex-a35-3d-graphics-4k-video-dsp-error-correcting-code-on-ddr:i.MX8X
These are actual commercial products we now support with an in-kernel
device tree source file:
- Bosch Guardian is a product made by Bosch Power
Tools GmbH, based on the Texas Instruments AM335x chip
- Winterland IceBoard is a Texas Instruments AM3874 based
machine used in telescopes at the south pole and elsewhere, see commit
d031773169 for some pointers:
- Inspur on5263m5 is an x86 server platform with an Aspeed
ast2500 baseboard management controller. This is for running on
the BMC.
- Zodiac Digital Tapping Unit, apparently a kind of ethernet
switch used in airplanes.
- Phicomm K3 is a WiFi router based on Broadcom bcm47094
- Methode Electronics uDPU FTTdp distribution point unit
- X96 Max, a generic TV box based on Amlogic G12a (S905X2)
- NVIDIA Shield TV (Darcy) based on Tegra210
And then there are several new SBC, evaluation, development or modular
systems that we add:
- Three new Rockchips rk3399 based boards:
- FriendlyElec NanoPC-T4 and NanoPi M4
- Radxa ROCK Pi 4
- Five new i.MX6 family SoM modules and boards for industrial
products:
- Logic PD i.MX6QD SoM and evaluation baseboad
- Y Soft IOTA Draco/Hydra/Ursa family boards based on i.MX6DL
- Phytec phyCORE i.MX6 UltraLite SoM and evaluation module
- MYIR Tech MYD-LPC4357 development based on the NXP lpc4357
microcontroller
- Chameleon96, an Intel/Altera Cyclone5 based FPGA development
system in 96boards form factor
- Arm Fixed Virtual Platforms(FVP) Base RevC, a purely
virtual platform for corresponding to the latest "fast model"
- Another Raspberry Pi variant: Model 3 A+, supported both
in 32-bit and 64-bit mode.
- Oxalis Evalkit V100 based on NXP Layerscape LS1012a,
in 96Boards enterprise form factor
- Elgin RV1108 R1 development board based on 32-bit Rockchips RV1108
For already supported boards and SoCs, we often add support for new
devices after merging the drivers. This time, the largest changes include
updates for
- STMicroelectronics stm32mp1, which was now formally
launched last week
- Qualcomm Snapdragon 845, a high-end phone and low-end laptop chip
- Action Semi S700
- TI AM654x, their recently merged 64-bit SoC from the OMAP family
- Various Amlogic Meson SoCs
- Mediatek MT2712
- NVIDIA Tegra186 and Tegra210
- The ancient NXP lpc32xx family
- Samsung s5pv210, used in some older mobile phones
Many other chips see smaller updates and bugfixes beyond that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=1goV
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"This is a smaller update than the past few times, but with just over
500 non-merge changesets still dwarfes the rest of the SoC tree.
Three new SoC platforms get added, each one a follow-up to an existing
product, and added here in combination with a reference platform:
- Renesas RZ/A2M (R7S9210) 32-bit Cortex-A9 Real-time imaging
processor:
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rza/rza2m.html
- Renesas RZ/G2E (r8a774c0) 64-bit Cortex-A53 SoC "for Rich Graphics
Applications":
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg2e.html
- NXP i.MX8QuadXPlus 64-bit Cortex-A35 SoC:
https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/i.mx-applications-processors/i.mx-8-processors/i.mx-8x-family-arm-cortex-a35-3d-graphics-4k-video-dsp-error-correcting-code-on-ddr:i.MX8X
These are actual commercial products we now support with an in-kernel
device tree source file:
- Bosch Guardian is a product made by Bosch Power Tools GmbH, based
on the Texas Instruments AM335x chip
- Winterland IceBoard is a Texas Instruments AM3874 based machine
used in telescopes at the south pole and elsewhere, see commit
d031773169 for some pointers:
- Inspur on5263m5 is an x86 server platform with an Aspeed ast2500
baseboard management controller. This is for running on the BMC.
- Zodiac Digital Tapping Unit, apparently a kind of ethernet switch
used in airplanes.
- Phicomm K3 is a WiFi router based on Broadcom bcm47094
- Methode Electronics uDPU FTTdp distribution point unit
- X96 Max, a generic TV box based on Amlogic G12a (S905X2)
- NVIDIA Shield TV (Darcy) based on Tegra210
And then there are several new SBC, evaluation, development or modular
systems that we add:
- Three new Rockchips rk3399 based boards:
- FriendlyElec NanoPC-T4 and NanoPi M4
- Radxa ROCK Pi 4
- Five new i.MX6 family SoM modules and boards for industrial
products:
- Logic PD i.MX6QD SoM and evaluation baseboad
- Y Soft IOTA Draco/Hydra/Ursa family boards based on i.MX6DL
- Phytec phyCORE i.MX6 UltraLite SoM and evaluation module
- MYIR Tech MYD-LPC4357 development based on the NXP lpc4357
microcontroller
- Chameleon96, an Intel/Altera Cyclone5 based FPGA development system
in 96boards form factor
- Arm Fixed Virtual Platforms(FVP) Base RevC, a purely virtual
platform for corresponding to the latest "fast model"
- Another Raspberry Pi variant: Model 3 A+, supported both in 32-bit
and 64-bit mode.
- Oxalis Evalkit V100 based on NXP Layerscape LS1012a, in 96Boards
enterprise form factor
- Elgin RV1108 R1 development board based on 32-bit Rockchips RV1108
For already supported boards and SoCs, we often add support for new
devices after merging the drivers. This time, the largest changes
include updates for
- STMicroelectronics stm32mp1, which was now formally launched last
week
- Qualcomm Snapdragon 845, a high-end phone and low-end laptop chip
- Action Semi S700
- TI AM654x, their recently merged 64-bit SoC from the OMAP family
- Various Amlogic Meson SoCs
- Mediatek MT2712
- NVIDIA Tegra186 and Tegra210
- The ancient NXP lpc32xx family
- Samsung s5pv210, used in some older mobile phones
Many other chips see smaller updates and bugfixes beyond that"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (506 commits)
ARM: dts: exynos: Fix max voltage for buck8 regulator on Odroid XU3/XU4
dt-bindings: net: ti: deprecate cpsw-phy-sel bindings
ARM: dts: am335x: switch to use phy-gmii-sel
ARM: dts: am4372: switch to use phy-gmii-sel
ARM: dts: dm814x: switch to use phy-gmii-sel
ARM: dts: dra7: switch to use phy-gmii-sel
arch: arm: dts: kirkwood-rd88f6281: Remove disabled marvell,dsa reference
ARM: dts: exynos: Add support for secondary DAI to Odroid XU4
ARM: dts: exynos: Add support for secondary DAI to Odroid XU3
ARM: dts: exynos: Disable ARM PMU on Odroid XU3-lite
ARM: dts: exynos: Add stdout path property to Arndale board
ARM: dts: exynos: Add minimal clkout parameters to Exynos3250 PMU
ARM: dts: exynos: Enable ADC on Odroid HC1
arm64: dts: sprd: Remove wildcard compatible string
arm64: dts: sprd: Add SC27XX fuel gauge device
arm64: dts: sprd: Add SC2731 charger device
arm64: dts: sprd: Add ADC calibration support
arm64: dts: sprd: Remove PMIC INTC irq trigger type
arm64: dts: rockchip: Enable tsadc device on rock960
ARM: dts: rockchip: add chosen node on veyron devices
...
- Interrupt support to Armada 7K/8K thermal nodes
- Armada 37xx related patches allowing to enable suspend to RAM
(USB2, USB3, PCIe, SATA, DSA)
- uDPU board support (Armada-3720 based):single-port FTTdp
distribution point unit
- Fixes for EspressoBin Ethernet support when using U-Boot mainline
- cleanup for partitions under flashes nodes
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXF3x1wAKCRALBhiOFHI7
1ZtFAJ4pn8nIeHqWgYEUmWmCpQXnUoc4eQCgninj7JcAFV8KNLKhRCkKdlkeO38=
=Wt6S
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-5.1-1' of git://git.infradead.org/linux-mvebu into arm/dt
mvebu dt64 for 5.1 (part 1)
- Interrupt support to Armada 7K/8K thermal nodes
- Armada 37xx related patches allowing to enable suspend to RAM
(USB2, USB3, PCIe, SATA, DSA)
- uDPU board support (Armada-3720 based):single-port FTTdp
distribution point unit
- Fixes for EspressoBin Ethernet support when using U-Boot mainline
- cleanup for partitions under flashes nodes
* tag 'mvebu-dt64-5.1-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: armada-37xx: link USB hosts with their PHYs
arm64: dts: marvell: armada-3720-espressobin: declare SATA PHY property
arm64: dts: marvell: armada-3720-espressobin: declare PCIe PHY
arm64: dts: marvell: armada-37xx: declare the COMPHY node
arm64: dts: marvell: Remove unnecessary #address-cells/#size-cells under flashes
arm64: dts: armada-3720-espressobin: Set mv88e6341 cpu port as RGMII-ID
arm64: dts: armada-3720-espressobin: Configure RGMII and SMI pins
arm64: dts: marvell: Add device tree for uDPU board
arm64: dts: marvell: armada-3720-espressobin: declare PCIe warm reset pin
arm64: dts: marvell: armada-37xx: declare PCIe reset pin
arm64: dts: marvell: armada-37xx: declare USB2 UTMI PHYs
arm64: dts: marvell: armada-37xx: fix USB2 memory region
arm64: dts: marvell: armada-37xx: declare SATA clock
arm64: dts: marvell: armada-37xx: fix SATA node scope
arm64: dts: marvell: add interrupt support to cp110 thermal node
arm64: dts: marvell: add interrupt support to ap806 thermal node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reference the PHY nodes from the USB controller nodes.
The USB3 host controller is wired to:
* the first PHY of the COMPHY IP
* the OTG-capable UTMI PHY
The USB2 host controller is wired to:
* the host-only UTMI PHY
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The SATA node is wired to the third PHY of the COMPHY IP.
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The PCIe node is wired to the second PHY of the COMPHY IP.
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Describe the A3700 COMPHY node. It has three PHYs that can be
configured as follow:
* PCIe or GbE
* USB3 or GbE
* SATA or USB3
Each of them has its own memory area.
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
By using the new binding for the partitions for the flashes we don't need
anymore to use #size-cells and #address-cells at the flash node level.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The mv88e6341 ethernet switch needs the cpu port control register to be
set with TX and RX internal delay in order to work.
This fixes ethernet support on system booted via a bootloader that
has not already configured this register (e.g. mainline u-boot, or
vendor u-boot compiled without ethernet support).
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
In order to be able to communicate with the 88e6341 switch some pins
have to be repurposed as RGMII and SMI pins.
This fixes ethernet support on system booted via a bootloader that
has not already configured those pins (e.g. mainline u-boot, or vendor
u-boot compiled without ethernet support).
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This adds initial support for micro-DPU (uDPU) board which is based on
Armada-3720 SoC. micro-DPU is the single-port FTTdp distribution point
unit made by Methode Electronics which offers complete modularity with
replaceable SFP modules both for uplink and downlink (G.hn over
twisted-pair, G.hn over coax, 1G and 2.5G Ethernet over Cat-5e cable).
On-board features:
- 512 MiB DDR3
- 2 x 2.5G SFP via HSGMII SERDES interface to the A3720 SoC
- USB 2.0 Type-C connector
- 4GB eMMC
- ETSI TS 101548 reverse powering via twisted pair (RJ45) or coax (F Type)
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Luis Torres <luis.torres@methode.com>
Cc: Scott Roberts <scott.roberts@telus.com>
Cc: Paul Arola <paul.arola@telus.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Ensure the PCIe endpoint card reset that is toggled by the PCIe
controller itself is muxed correctly on the EspressoBin.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
One pin can be muxed as PCIe endpoint card reset.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
On Marvell Armada 3700 SoCs there are two USB2 UTMI PHYs. They are
both very similar but only one has OTG/charging capabilities.
Because there are USB host registers and PHY registers mixed in a
single area, a system controller is also created and referenced from
both the USB host node and the PHY node.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The specification splits the USB2 memory region into three sections:
1/ 0xD005E000-0xD005EFFF: USB2 Host Controller Registers
2/ 0xD005F000-0xD005F7FF: USB2 UTMI PHY Registers
3/ 0xD005F800-0xD005FFFF: USB2 Host Miscellaneous Registers
Section 1/ belongs to the USB2 node but section 2/ belongs to the UTMI
PHY node. Section 3/ can be accessed by both the USB controller and
the PHY because of the miscaellaneous nature of the registers inside
so a specific node will be created to cover the area and a handle to
it will be added in both the USB controller and the PHY node.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The SATA IP get its clock from the north-bridge.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Fix the SATA IP memory area which is only 0x178 bytes long (from
Marvell A3700 specification). Actually, starting from the offset
0xe0178, there is an area dedicated to the COMPHY driver.
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add interrupt properties in the thermal node as well as a critical trip
point in the thermal-zone.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add interrupt properties in the thermal node as well as a critical trip
point in the thermal-zone.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The 'arm,armv8' compatible string is only for software models. It adds
little value otherwise and is inconsistently used as a fallback on some
platforms. Remove it from those platforms.
This fixes warnings generated by the DT schema.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Chanho Min <chanho.min@lge.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The MPP52 signal is on the seconds GPIO instance of CP0, which
corresponds to the &cp0_gpio2 handle.
Rename the property name to the standard '-gpios' suffix while at it.
Fixes: b83e1669ad ("arm64: dts: marvell: mcbin: add support for PCIe")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The memory area [0x4000000-0x4200000[ is occupied by the PSCI firmware. Any
attempt to access it from Linux leads to an immediate crash.
So let's make the same memory reservation as the vendor kernel.
[gregory: added as comment that this region matches the mainline U-boot]
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a fragment,
that later gets filled in on later releases, and in some cases it's
near-complete platform support. The latter is more common for derivative
platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions. Allwinner
support for F1C100s, a quite old SoC (ARMv5-based) shipping in the
Lychee Pi Nano platform. At the other end is NXP Layerscape LX2160A,
a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O aimed at
infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to devicetree,
which opens up for removal of even more of their platform-specific
'hwmod' description tables over the next few releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board
-----BEGIN PGP SIGNATURE-----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=sFVi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a
fragment, that later gets filled in on later releases, and in some
cases it's near-complete platform support. The latter is more common
for derivative platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions.
Allwinner support for F1C100s, a quite old SoC (ARMv5-based) shipping
in the Lychee Pi Nano platform. At the other end is NXP Layerscape
LX2160A, a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O
aimed at infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to
devicetree, which opens up for removal of even more of their
platform-specific 'hwmod' description tables over the next few
releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (648 commits)
ARM: dts: suniv: Fix improper bindings include patch
ARM: dts: sunxi: Enable Broadcom-based Bluetooth for multiple boards
arm64: dts: allwinner: a64: bananapi-m64: Add Bluetooth device node
ARM: dts: suniv: Fix improper bindings include patch
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Remove unused properties from FSL QSPI driver nodes
arm64: dts: ti: k3-am654: Enable main domain McSPI0
arm64: dts: ti: k3-am654: Add McSPI DT nodes
arm64: dts: ti: k3-am654: Populate power-domain property for UART nodes
arm64: dts: ti: k3-am654-base-board: Enable ECAP PWM
arm64: dts: ti: k3-am65-main: Add ECAP PWM node
arm64: dts: ti: k3-am654-base-board: Add I2C nodes
arm64: dts: ti: am654-base-board: Add pinmux for main uart0
arm64: dts: ti: k3-am65: Add pinctrl regions
dt-bindings: pinctrl: k3: Introduce pinmux definitions
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
...
Enable the USB3 peripheral that is wired to CON2 on the Clearfog GT-8K
board.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add DT support for the Macchiatobin Single Shot board from SolidRun,
which is similar to the Double Shot board, but does not have the
10G 3310 PHYs - the two ethernet ports are instead connected directly
to the SFP+ cages.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The ESPRESSObin board has a emmc interface available on U11: declare it
and let the bootloader enable it if the emmc is present.
[gregory.clement@bootlin.com: disable the emmc by default]
Signed-off-by: Ding Tao <miyatsu@qq.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This reverts commit 8ed4636877.
This commit breaks boot on Armada 8K based systems. Reverting it makes
affected systems boot again.
Reported-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Deassert the reset and wireless disable signals on the CON2 mini-PCIe
socket. That allows the host to detect USB devices on the mini-PCIe
socket.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This reset signal controls the Marvell 1512 1G PHY.
Note that current implementation queries the PHY over the MDIO bus
(get_phy_device() call from of_mdiobus_register_phy()) before reset
signal deassert. If the PHY reset signal is asserted at boot time, PHY
registration fails. So current code relies on the bootloader to deassert
the reset signal.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The fixed regulator driver ignores the gpio flags, so this change has
no practical effect in the current implementation. Fix it anyway to
correct the hardware description.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This adds support for the PCIe interface on the CON4 mini-PCIe
connector.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The ICU handles several interrupt groups, each of them being a subpart
of the ICU node.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Create an ICU subnode for the NSR interrupts. This subnode becomes the
CP110 interrupt parent, removing the need for the ICU_GRP_NSR parameter.
Move all DT110 nodes to use these new bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add the System Error Interrupt node, representing an IRQ chip which is
part of the GIC. The SEI node aggregates interrupts from the AP through
wired interrupts, and from the CPs through MSIs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This patch adds CPU deep Idle and Cluster deep Idle states BUT it defines
the idle state for each cpu (defined under cpu-idle-states parameter)
only for the quad version therefore it does NOT activate CPU Idle
capability for the other version.
[gregory: extract from a larger patch]
Signed-off-by: orenbh <orenbh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Aligned with what we have done for the others nodes. It will also allow
to easily modify the cpu configuration at board (or sub-SoC) level.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This adds the system controller node for CPU Miscellaneous Registers
(which is needed for the watchdog node) and the watchdog node.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This patch describes 3 additional interrupts per PPv2 port. Those
interrupts will be used later in future versions of the Marvell PPv2
driver, and now the device tree description matches the hardware
capabilities.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This patch changes the PPv2 IRQ names in the CP110 device tree to match
a corresponding change in the Marvell PPv2 driver. The reason this was
updated is the IRQ where names after Tx/Rx interrupts, but this is not
true and can be configured. A following patch will add more of them and
the names wouldn't make sense.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The SolidRun Clearfog GT-8K is based on Marvell Armada 8040 SoC.
https://wiki.solid-run.com/doku.php?id=products:a8040:clearfoggt8k
The following devices were tested with this DT on top of kernel
v4.19-rc4:
* 1GB Ethernet WAN
* 4 ports 1GB Ethernet switch (2.5GB uplink)
* SFP port
* SATA on CON3 PCIe slot
* USB3 type A port
* SD card and eMMC
* 2 LEDs
* 2 push buttons
[gregory: fix block comment alignement]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add a thermal-zone node and fill in all the sensors available in a
cp110 (only one in the thermal IP).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Because the label is different between CPs, the full path of a node is
unique. However, when referring to the end of the path only (the node
name), this name is not unique anymore.
The *thermal_zone_of_sensor_register() functions of the thermal core
present this limitation and prevent having a thermal-zone per CP.
Add a macro to make the distinction between node names to solve this
situation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add a thermal-zone node and fill in all the sensors available in an
ap806 (one in the IC plus one per CPU).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
New bindings impose to declare the thermal IP from within a new syscon.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Use more specific compatible for the Inside Secure SafeXcel on the
Armada 37xx and the Armada 7K/8K SoCs.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCW1GhYAAKCRALBhiOFHI7
1UYeAKCZvsX0evzDYPCmL32CSuArmJ+OKwCdFYn7QoXQIYwGP60bK2UZzhcWROs=
=V7S+
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.19-2' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt64 for 4.19 (part 2)
Use more specific compatible for the Inside Secure SafeXcel on the
Armada 37xx and the Armada 7K/8K SoCs.
* tag 'mvebu-dt64-4.19-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: armada-37xx: update the crypto engine compatible
arm64: dts: marvell: armada-cp110: update the crypto engine compatible
Signed-off-by: Olof Johansson <olof@lixom.net>
Armada 3700
- Add default memory reservation for ATF
- Add a node for AVS support
Fix eth3 connector name on the Macchiatobin
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCW0hwpQAKCRALBhiOFHI7
1WtcAKCGbi1l3gHxOT0WdMtx3vjxIlySYgCgknnIsyIO3uDuujsEOH9nGhzyDAo=
=KfNs
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.19-1' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt64 for 4.19 (part 1)
Armada 3700
- Add default memory reservation for ATF
- Add a node for AVS support
Fix eth3 connector name on the Macchiatobin
* tag 'mvebu-dt64-4.19-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: armada-37xx: reserve memory for ATF
arm64: dts: marvell: armada-37xx: add the node allowing AVS support
arm64: dts: marvell: mcbin: fix eth3 connector name
Signed-off-by: Olof Johansson <olof@lixom.net>
New compatibles are now supported by the Inside Secure SafeXcel driver.
As they are more specific than the old ones, they should be used
whenever possible. This patch updates the Marvell Armada 37xx device
tree accordingly.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
New compatibles are now supported by the Inside Secure SafeXcel driver.
As they are more specific than the old ones, they should be used
whenever possible. This patch updates the Marvell cp110 device tree
accordingly.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The PSCI area should be reserved in Linux for PSCI operations such as
suspend/resume.
Reserve 2MiB of memory which matches the area used by ATF (BL1, BL2,
BL3x, see [1] in ATF source code). This covers all PSCI code and data
area and is 2MiB aligned, which is required by Linux for huge pages
handling.
Please note that this is a default setup allowing to perform PSCI
operations with legacy bootloaders. Recent bootloaders should update the
region size/position accordingly.
[1] plat/marvell/a3700/common/include/platform_def.h
Signed-off-by: Victor Gu <xigu@marvell.com>
[miquel.raynal@bootlin.com: reword of commit message, comment in the DTSI]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
In order to be able to use Adaptive Voltage Scaling, we need to add a
reference to these registers.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The right most SFP connector on the Macchiatobin board and schematics is
marked as CON13/CON14.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
- Use correct size for ICU nodes (irq controller) on Armada 7K/8K
- Fix "#cooling-cells" property's name on Synology DS116 (Armada 385)
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWwwZggAKCRALBhiOFHI7
1RZ3AJ4wjqNwkBmHpxD5DDQgNcO1WxYhFgCffMYB3qCIdYW6ROiFCs79bq/8Ldc=
=HA77
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.17-2' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 4.17 (part 2)
- Use correct size for ICU nodes (irq controller) on Armada 7K/8K
- Fix "#cooling-cells" property's name on Synology DS116 (Armada 385)
* tag 'mvebu-fixes-4.17-2' of git://git.infradead.org/linux-mvebu:
arm: dts: armada: Fix "#cooling-cells" property's name
arm64: dts: marvell: fix CP110 ICU node size
Signed-off-by: Olof Johansson <olof@lixom.net>
As always, a large number of DT updates. Too many to enumerate them all,
but at a glance:
New SoCs introduced in this release:
- Amlogic:
+ Meson 8M2 SoC, a.k.a. S812. A quad Cortex-A9 SoC used in some set
top boxes and other products.
- Mediatek:
+ MT7623A, which is a flavor of the MT7623 family with other on-chip
ethernet options.
- Qualcomm:
+ SDM845, a.k.a Snapdragon 845, an 4+4-core Kryo 385/845
(Cortex-A75/A55 derivative) SoC that's one of the current high-end
mobile SoCs.
It's great to see mainline support for it. So far, you
can't do much with it, since a lot of peripherals are not yet in the
DTs but driver support for USB, GPU and other pieces are starting to
trickle in. This might end up being a well-supported SoC upstream if
the momentum keeps up.
- Renesas:
+ R8A77990, a.k.a R-Car E3, a new automotive entertainment-targeted
SoC. Currently only one Cortex-A53 CPU is enabled, we are eagerly
awaiting more. So far, basic drivers such as serial, gpios, PMU and
ethernet are enabled.
+ R8A77470, a.k.a. RZ/G1C, a new dual Cortex-A7 SoC with PowerVR
GPU. Same here, basic set of drivers such as serial, gpios and ethernet
enabled, and SMP support is also forthcoming.
- STMicroelectronics:
+ STM32F469, very similar tih STM32F429 but with display support
Enhancements to SoCs/platforms (DTS contents, some driver portions might
not be in yet):
- Allwinner sun8i (h3/a33/a83t) SMP, DVFS tweaks, misc
- Amlogic Meson: I2C, UFS, TDM, GPIO external interrupts, MMC resets
- Hisilicon hi3660: Thermal cooling, CPU frequency scaling, mailbox interfaces
- Marvell Berlin2CD: SMP support, thermal sensors
- Mediatek MT7623: Highspeed DMA, audio support
- Qualcomm IPQ8074 PCIe support, MSM8996 UFS support
- Renesas: Watchdog and PMU support across many platforms
- Rockchip RK3399: USB3 OTG support
- Samsung Exynos: Audio-over-HDMI on Odroid X/X2/U3
- STMicro STM32: Lots of peripherals added to STM32MP175C
- Uniphier: Ethernet support
New boards:
- Allwinner A20: Olimex A20-SOM-EVB-eMMC variant
- Allwinner H2+: Libre Computer ALL-H3-CC (h2+ version)
- Allwinner A33: Nintendo NES/SuperNES Classic Edition
- Aspeed: S2600WF, Inventec Lanyang BMC, Portwell Neptune
- Berlin2CD: Valve Steam Link
- Broadcom BCM5301X: Luxul XAP-1610 and XWR-3150 V1
- Broadcom: Raspberry Pi 3 B+
- Mediatek MT7623N and MT7623A: reference boards
- Meson 8M2: Tronsmart MXIII Plus
- NXP i.MX: Engicam i.CoreM6, DHCOM iMX6 SOM, BTicino i.MX6DL Mamoj
- Qualcomm MSM8974: Sony Xperia Z1 Compact support
- Qualcomm SDM845: MTP development board
- Renesas: Ebisu R8A77990 board
- Renesas RZ/G1C: iwg23s: iWave G235-SDB
- TI am335x: Pocketbeagle support
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAlsfBtUPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3wfYQAI1hlPhRx7H1zbc59zdlW6daY7y1+dXuqoCs
K5Hxsurlsbnx9fjeGcBp/razL5YtdZmBYII8IBhKzhLKp/A0gqmX7W9pTNQj9/Sp
SOIl8dci/yr0HUpgwc4IdVhJBdpplv48GK3q8opSocI/J9dnD873NHLlvTpCB+Jy
GCD9tB56JnOfTO+n0Yg+tyuig1jIQCc52Iwnmxv2vYPbsHUaEmqz1Z+wBe0BaDk+
eVsohNQI/2xxRzv8PE13H/ojcZ532rF45aw6ypRwCvg1MzCYXSdKLJlIWx8Ci581
YmRPlCOWai+AxSATgJhIR9n9dxn6hqxEgVyu7AOxPVa0O4DKB3oy8PPo5wlOCKcU
J1n5zJwnULWw4eVa1ag/cEMbz95QMC1F9MmyiLUfz3esHwyD/Gl3ks9v1gwn9XYp
xsI+oGnMy/Uz4oZ1/XM5CO5UUDXyixVD3pYEF8wLaYX2JY8zETI5qfvNL0bwZX3P
lLFCI7Xdwsk3+HCp7aHs4KkWHLVGq65SxrXKTIpU+vEq+0RYiV/cWP9Swa/RNrMH
gB00oZ2TBRuIr/KxsCKyCkKApocW4J4WtZ2sMY7QDXzW68lq8oIbefY+6Abgk4/7
6J7D5n0gmTB38wrzZCY5UF0eQrLjPwnxuLywEll5oLFbNTr/7Aruk2kFYEMGjM9E
QmXGoHXU
=jLvk
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Olof Johansson:
"As always, a large number of DT updates. Too many to enumerate them
all, but at a glance:
New SoCs introduced in this release:
- Amlogic:
+ Meson 8M2 SoC, a.k.a. S812. A quad Cortex-A9 SoC used in some
set top boxes and other products.
- Mediatek:
+ MT7623A, which is a flavor of the MT7623 family with other
on-chip ethernet options.
- Qualcomm:
+ SDM845, a.k.a Snapdragon 845, an 4+4-core Kryo 385/845
(Cortex-A75/A55 derivative) SoC that's one of the current
high-end mobile SoCs.
It's great to see mainline support for it. So far, you can't do
much with it, since a lot of peripherals are not yet in the DTs
but driver support for USB, GPU and other pieces are starting to
trickle in. This might end up being a well-supported SoC
upstream if the momentum keeps up.
- Renesas:
+ R8A77990, a.k.a R-Car E3, a new automotive
entertainment-targeted SoC. Currently only one Cortex-A53 CPU is
enabled, we are eagerly awaiting more. So far, basic drivers
such as serial, gpios, PMU and ethernet are enabled.
+ R8A77470, a.k.a. RZ/G1C, a new dual Cortex-A7 SoC with PowerVR
GPU. Same here, basic set of drivers such as serial, gpios and
ethernet enabled, and SMP support is also forthcoming.
- STMicroelectronics:
+ STM32F469, very similar tih STM32F429 but with display support
Enhancements to SoCs/platforms (DTS contents, some driver portions
might not be in yet):
- Allwinner sun8i (h3/a33/a83t) SMP, DVFS tweaks, misc
- Amlogic Meson: I2C, UFS, TDM, GPIO external interrupts, MMC resets
- Hisilicon hi3660: Thermal cooling, CPU frequency scaling, mailbox interfaces
- Marvell Berlin2CD: SMP support, thermal sensors
- Mediatek MT7623: Highspeed DMA, audio support
- Qualcomm IPQ8074 PCIe support, MSM8996 UFS support
- Renesas: Watchdog and PMU support across many platforms
- Rockchip RK3399: USB3 OTG support
- Samsung Exynos: Audio-over-HDMI on Odroid X/X2/U3
- STMicro STM32: Lots of peripherals added to STM32MP175C
- Uniphier: Ethernet support
New boards:
- Allwinner A20: Olimex A20-SOM-EVB-eMMC variant
- Allwinner H2+: Libre Computer ALL-H3-CC (h2+ version)
- Allwinner A33: Nintendo NES/SuperNES Classic Edition
- Aspeed: S2600WF, Inventec Lanyang BMC, Portwell Neptune
- Berlin2CD: Valve Steam Link
- Broadcom BCM5301X: Luxul XAP-1610 and XWR-3150 V1
- Broadcom: Raspberry Pi 3 B+
- Mediatek MT7623N and MT7623A: reference boards
- Meson 8M2: Tronsmart MXIII Plus
- NXP i.MX: Engicam i.CoreM6, DHCOM iMX6 SOM, BTicino i.MX6DL Mamoj
- Qualcomm MSM8974: Sony Xperia Z1 Compact support
- Qualcomm SDM845: MTP development board
- Renesas: Ebisu R8A77990 board
- Renesas RZ/G1C: iwg23s: iWave G235-SDB
- TI am335x: Pocketbeagle support"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (448 commits)
ARM: dts: aspeed: Fix hwrng register address
arm64: dts: sprd: whale2: Add the rtc enable clock for watchdog
arm64: dts: sprd: Add GPIO and GPIO keys device nodes
arm64: dts: sprd: fix typo in 'remote-endpoint'
arm64: dts: apq8096-db820c: Removed bt-en-1-8v regulator
arm64: dts: fix regulator property name for wlan pcie endpoint
arm64: dts: qcom: msm8996: Use UFS_GDSC for UFS
ARM: dts: pxa3xx: fix MMC clocks
ARM: pxa: dts: add pin definitions for extended GPIOs
ARM: pxa: dts: add gpio-ranges to gpio controller
ARM: dts: ipq8074: Enable few peripherals for hk01 board
ARM: dts: ipq8074: Add pcie nodes
ARM: dts: ipq8074: Add peripheral nodes
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c2 board file
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c1 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk07.1 common data
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk04.1-c3 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk04.1-c1 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk04.dtsi
ARM: dts: ipq4019: Change the max opp frequency
...
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEE2MW6uuYZ+0zBfpF41kg+k28NbwgFAlsGU58THGpzemhhbmcz
QGdtYWlsLmNvbQAKCRDWSD6Tbw1vCOOzD/4wBhoFn/97yrZSJeOpbctEFmqjWuls
d1ogSCRTOvmlG6FwBXFoZiatF6DwMjkv0hKxuhW4wjmV6n9HwlgonAYXurHMAD0a
xSHbjEqvu1aX8XGPRq0WKa/oyQrCLCiiO6/9+hIfIZbGoRVkkLWBQ7KB+1UMpgPb
Y9BCoPaOrFR78emcNDjBVkZ+QWCnOm2MkQO7CZa8DOrgsNEW5247hE0c6H2fwRa1
5kulVElAs2XVlx9HXxiNbrhDA7kwvxCSJiFkCB/w3YsSdSk7RUN/cSXj5xSnFdPW
74gD/fCzLyL3vVkogegqBmpSh6NavppZlw0yJlDeszQGO/YXjDpu2Tol+Mp7KH0W
LdIJltdc/kqe7bw8eSm3cWwJiXtSIzFX5Rn456DxvezWUF4rjSZgUu41bnBR7KHw
Kq/w1800pU6pHFvx57Kq/zIid5usB83BoOVuMz0Ul86b/dbBvxQdzZlHbT0/ZVkD
l5UcaoCvNh4NzDbx5fRGLwTLcaUz0ZJb0M6MxM/Dm/+qebU/0tMowPsV9hk7G7Vb
QyfdU8b4dUYZAlFp+sSvEXXo1qfAREofdIpDsVYvTQqepdoelk8K93uzTUUdqWCc
INBpe0sZpT82vq1Rc2svyMysQhFKboyWwjR0DHOTOU64g8tC280M1ozB1eptf0N0
BQrlrw1ttJWmJA==
=corl
-----END PGP SIGNATURE-----
Merge tag 'berlin64-dt-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin into next/dt
Berlin64 DT changes for v4.18
* tag 'berlin64-dt-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin:
arm64: dts: move berlin SoC files from marvell dir to synaptics dir
arm64: dts: berlin4ct-*.dts: use SPDX-License-Identifier
arm64: dts: berlin4ct: use SPDX-License-Identifier
Signed-off-by: Olof Johansson <olof@lixom.net>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
ICU size in CP110 is not 0x10 but at least 0x440 bytes long (from the
specification).
Fixes: 6ef84a827c ("arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This allows to reference these gpio controller as interrupt parent. Also
add a comment which cpu line names are managed by the controllers
because "nb" and "sb" usually doesn't appear in schematics, but MPPX_Y
do.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This patch adds a fixed-link node to the 10G interface of the 7040-db
board. This is required as the mvpp2 driver now uses phylink. The best
solution would have been to describe the SFP cage but they are not
wired correctly, and thus unusable, so we chose to use fixed-link
instead.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This patch adds a fixed-link node to both 10G interfaces of the 8040-db
board. This is required as the mvpp2 driver now uses phylink. The best
solution would have been to describe the SFP cages but they are not
wired correctly, and thus unusable, so we chose to use fixed-link
instead.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This patch enables the fourth network interface on the Marvell
Macchiatobin. It is configured in the 2500Base-X PHY mode. The SFP cage
is also described.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This patch adds the SFP cage description in the Marvell Armada 8040
mcbin, for both 10G interfaces.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[Antoine: small reworks, commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Marvell PPv2.2 controller present on CP-110 need the extra "mg_core_clk"
clock to avoid system hangs when powering some network interfaces up.
This issue appeared after a recent clock rework on Armada 7K/8K platforms.
This commit adds the new clock and updates the documentation accordingly.
[gregory.clement: use the real first commit to fix and add the cc:stable
flag]
Fixes: e3af9f7c6e ("RM64: dts: marvell: armada-cp110: Fix clock resources for various node")
Cc: <stable@vger.kernel.org>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The Marvell XSMI controller needs 3 clocks to operate correctly :
- The MG clock (clk 5)
- The MG Core clock (clk 6)
- The GOP clock (clk 18)
This commit adds them, to avoid system hangs when using these
interfaces.
[gregory.clement: use the real first commit to fix and add the cc:stable
flag]
Fixes: f66b2aff46 ("arm64: dts: marvell: add xmdio nodes for 7k/8k")
Cc: <stable@vger.kernel.org>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The hardware is clearly DMA coherent and not marking it as such leads
to cache coherency problems, at least with the OpenBSD kernel.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This is the storage the machine boots from by default. The partitioning
is taken from the U-Boot that is shipped with the board. There is some
more space on the flash that isn't used.
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Ellie Reeves <ellierevves@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The schematic of the espressobin is publicly available, add a comment
where to find it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the PCIe host
controller used on CP110 component of the Armada 7K/8K SoCs.
This follow the changes already made in the binding documentation (as
well as in the driver): "PCI: armada8k: Fix clock resource by adding
a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the NAND controller
used on CP110 component of the Armada 7K/8K SoCs.
This follow the changes already made in the binding documentation (as
well as in the driver): "mtd: nand: marvell: Fix clock resource by adding
a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the safexcel EIP97
used on CP110 component of the Armada 7K/8K SoCs.
This follow the changes already made in the binding documentation (as
well as in the driver): "crypto: inside-secure - fix clock resource by
adding a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the harware RNG
used on CP110 component of the Armada 7K/8K SoCs.
This follow the changes already made in the binding documentation (as
well as in the driver): "hwrng: omap - Fix clock resource by adding a
register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the XOR engine
controller used on CP110 component of the Armada 7K/8K SoCs.
This follow the changes already made in the binding documentation (as
well as in the driver): "dmaengine: mv_xor_v2: Fix clock resource by
adding a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the USB host
controller used on Armada 7K/8K SoCs.
This follow the changes already made in the binding documentation (as
well as in the driver): "usb: host: xhci-plat: Fix clock resource by
adding a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the UARTs used on
CP110 component of the Armada 7K/8K SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Use the new bindings of the reworked Marvell NAND controller driver.
Also adapt the nand controller node organization to distinguish which
property is relevant for the controller, and which one is NAND chip
specific. Expose the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore as
the driver activates the arbiter by default for all boards (either
needed or harmless).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Use the new bindings of the reworked Marvell NAND controller driver.
Also adapt the nand controller node organization to distinguish which
property is relevant for the controller, and which one is NAND chip
specific. Expose the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore as
the driver activates the arbiter by default for all boards (either
needed or harmless).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the AHCI SATA
controller used on the Armada 7K/8K SoCs.
The ahci drivers was already designed to support up to 5 clocks so there
is only need to update the device tree to use it. It was not noticed
until now because of wrong assumption in the clock drivers, but as this
IP really needs 2 clocks, we had to declare both of them.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
A 'C' was missing in the model name, this patch fixes it.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add description of the J25 and J27 UART headers of the Macchiatobin. They use
uart peripherals that the CP0 (J25) and CP1 (J27) provide.
Even though J25 and J27 are labeled as UART header, the pins on these headers
can be muxed for other purposes. But the UART functionality is useful when the
board is mounted in an ATX style enclosure, since the console UART is not
accessible through the microUSB at CON9.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The CP110 component has 4 uart peripherals. All of them use the same clock
gate for slow peripherals that is shared with the i2c and spi peripherals.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the I2C controller
used on the Armada 7K/8K SoCs.
This follows the changes already made in the binding documentation (as
well as in the driver) in:
commit 1534156e99 ("i2c: mv64xxx: Fix clock
resource by adding an optional bus clock")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the SPI controller
used on Armada 7K/8K SoCs.
This follows the changes already made in the binding documentation (as
well as in the driver) in:
'commit 92ae112e47 ("spi: orion: Fix clock
resource by adding an optional bus clock")'.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
When replacing the cpm by cp0 and cps by cp1 [1] not only the label and
the alias were replaced but also the compatible string which was wrong.
Due to this the pinctrl driver was no more probed.
This patch fix it by reverting this change for the pinctrl compatible
string on Armada 8K.
[1]: "arm64: dts: marvell: replace cpm by cp0, cps by cp1"
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds Ethernet aliases in the Marvell Armada 7040 DB, 8040 DB
and 8040 mcbin device trees so that the bootloader setup the MAC
addresses correctly.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message, small fixes]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
In preparation for the introduction of more than 2 CPs in upcoming
SoCs, it makes sense to move away from the "CP master" (cpm) and "CP
slave" (cps) naming, and use instead cp0/cp1.
This commit is the result of:
sed 's%cpm%cp0g%' arch/arm64/boot/dts/marvell/*
sed 's%cps%cp1g%' arch/arm64/boot/dts/marvell/*
So it is a purely mechaninal change.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Suggested-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
One concept of Marvell Armada 7K/8K SoCs is that they are made of HW
blocks composed of a variety of IPs (network, PCIe, SATA, XOR, SPI,
I2C, etc.), and those HW blocks can be duplicated several times within
a given SoC. The Armada 7K SoC has a single CP110 (so no duplication),
while the Armada 8K SoC has two CP110. In the future, SoCs with more
than 2 CP110s will be introduced.
In current kernel versions, the master CP110 is described in
armada-cp110-master.dtsi and the slave CP110 is described in
armada-cp110-slave.dtsi. Those files are basically exactly the same,
since they describe the same hardware. They only have a few
differences:
- Base address of the registers is different for the "config-space"
- Base address of the PCIe registers, MEM, CONF and IO areas were
different
- Labels (and phandles pointing to them) of the nodes were different
("cpm" prefix in the master CP, "cps" prefix in the slave CP)
This duplication issue has been discussed at the DT workshop [1] in
Prague last October, and we presented on this topic [2]. The solution
of using the C pre-processor to avoid this duplication has been
validated by the people present in this DT workshop, and this patch
simply implements what has been presented.
We handle differences between the master CP and slave CP description
using the C pre-processor, by defining a set of macros with different
values armada-cp110.dtsi is included to instantiate one of the master
or slave CP110.
There are a few aspects that deserve additional explanations:
- PCIe needs to be handled separately because it is not part of the
config-space {...} node, since it has registers outside of the
range covered by config-space {...}.
- We need to defined CP110_BASE, CP110_PCIEx_BASE without 0x, because
they are used for the unit address part of some DT nodes. But since
they are also used for the "reg" property of the same nodes, we
have an ADDRESSIFY() macro that prepends 0x to those values.
We compared the resulting .dtb for armada-8040-db.dtb before and after
this patch is applied, and the result is exactly the same, except for
a few differences:
- the SDHCI controller that was only described in the master CP110 is
now also described in the slave CP110. Even though the SDHCI
controller from the slave CP110 is indeed not usable (as it isn't
wired to the outside world) it is technically part of the silicon,
and therefore it is reasonable to also describe it to be part of
the slave CP110. In addition, if we wanted to get this correct for
the SDHCI controller, we should also do it for the NAND controller,
for which the situation is even more complicated: in a single CP110
configuration (Armada 7K), the usable NAND controller is in the
master CP110, while in a dual CP110 configuration (Armada 8K), the
usable NAND controller is in the slave CP110. Since that would add
a lot of additional complexity for no good reason, and since the IP
blocks are in fact really present in both CPs, we simply describe
them in both CPs at the DT level.
- the cp110-master and cp110-slave nodes are now named cpm and
cps. We could have kept cp110-master and cp110-slave, but that
would have required adding another CP110_xyz define, which didn't
seem very useful.
Note that this commit also gets rid of the armada-cp110-master.dtsi
and armada-cp110-slave.dtsi files, as future SoCs will have more than
2 CPs. Instead, we instantiate the CPs directly from the SoC-specific
.dtsi files, i.e armada-70x0.dtsi and armada-80x0.dtsi.
[1] https://elinux.org/Device_tree_kernel_summit_2017_etherpad
[2] https://elinux.org/images/1/14/DTWorkshop2017-duplicate-data.pdf
[gregory.clement@free-electrons.com: add back the "ARM64: dts: marvell:
Fix clock resources for various node" commit]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
We are currently using the cell-index DT property to assign SPI bus
numbers. This property is specific to the spi-orion driver, and
requires each SPI controller to have a unique ID defined in the Device
Tree.
As we are about to merge armada-cp110-master.dtsi and
armada-cp110-slave.dtsi into a single file, those cell-index
properties that differ between the master CP110 and the slave CP110
are a difference that would have to be handled.
In order to avoid this, we switch to using the "aliases" DT node to
assign a unique number to each SPI controller. This is more generic,
and directly handled by the SPI core.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Back when the ICU Device Tree binding was introduced, we could not use
mvebu-icu.h from the Device Tree files, because the DT files and
mvebu-icu.h were following different merge routes towards Linus
tree. Now that both have been merged, we can switch the Marvell Armada
CP110 Device Tree files to use the mvebu-icu.h header instead of
duplicating the ICU_GRP_NSR definition.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada CP110 slave NAND controller Device Tree description lists
the compatible string in the wrong order: marvell,armada-8k-nand
should come first. This commit alignes the slave CP110 description
with the master CP110 description from that respect.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fix the same typo duplicated in both master and slave version of
armada-cp110-*.dtsi file: s/limiation/limitation/.
[gregory.clement@free-electrons.com: add the commit log]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This fixes the following DTC warning:
<stdout>: Warning (simple_bus_reg): Node /ap806/config-space@f0000000/thermal@6f808C simple-bus unit address format error, expected "6f808c"
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This fixes the following DTC warning:
Warning (simple_bus_reg): Node /ap806/config-space@f0000000/watchdog@600000 simple-bus unit address format error, expected "610000"
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds a crypto node describing the EIP97 engine found in
Armada 37xx SoCs. The cryptographic engine is enabled by default.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
On the CP modules we found on Armada 7K/8K, many IP block actually also
need a "functional" clock (from the bus). This patch add them which allows
to fix some issues hanging the kernel:
If Ethernet and sdhci driver are built as modules and sdhci was loaded
first then the kernel hang.
Fixes: bb16ea1742 ("mmc: sdhci-xenon: Fix clock resource by adding an
optional bus clock")
Cc: stable@vger.kernel.org
Reported-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
In order to be able to use cpu freq, we need to associate a clock to each
CPU and to expose the power management registers.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add NAND support on the Armada-8040-DB by adding the same tree as for
the Armada-7040-DB by using the same compatible string
"marvell,armada-8k-nand".
Do not enable the NAND node as enabling it (and changing manually the
proper DPR-76 switch) would disable MDIO from CP1 (and thus disable CPS
Ethernet PHY).
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
We add device tree files for a couple of additional SoCs in various areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for networking,
Amlogic A113D for audio, and Renesas R-Car V3M for automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX, Amlogic
and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues that
the latest version of 'dtc' now warns about. Unfortunately there is still
a lot left to do.
A rework of the ARM foundation model introduced several new files
for common variations of the model.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TnSo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Arnd Bergmann:
"We add device tree files for a couple of additional SoCs in various
areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for
networking, Amlogic A113D for audio, and Renesas R-Car V3M for
automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX,
Amlogic and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues
that the latest version of 'dtc' now warns about. Unfortunately there
is still a lot left to do.
A rework of the ARM foundation model introduced several new files for
common variations of the model"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (599 commits)
arm64: dts: uniphier: route on-board device IRQ to GPIO controller for PXs3
dt-bindings: bus: Add documentation for the Technologic Systems NBUS
arm64: dts: actions: s900-bubblegum-96: Add fake uart5 clock
ARM: dts: owl-s500: Add CubieBoard6
dt-bindings: arm: actions: Add CubieBoard6
ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock
ARM: dts: owl-s500: Set power domains for CPU2 and CPU3
arm: dts: mt7623: remove unused compatible string for pio node
arm: dts: mt7623: update usb related nodes
arm: dts: mt7623: update crypto node
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
...
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing memory
leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node. The
prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to dtb
compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage Technology,
shimafuji, Tecon Microprocessor Technologies, DH electronics GmbH,
Opal Kelly, and Next Thing
-----BEGIN PGP SIGNATURE-----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=jgpN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
If CONFIG_OF_ALL_DTBS is enabled, "make ARCH=arm64 dtbs" compiles each
DTB twice; one from arch/arm64/boot/dts/*/Makefile and the other from
the dtb-$(CONFIG_OF_ALL_DTBS) line in arch/arm64/boot/dts/Makefile.
It could be a race problem when building DTBS in parallel.
Another minor issue is CONFIG_OF_ALL_DTBS covers only *.dts in vendor
sub-directories, so this broke when Broadcom added one more hierarchy
in arch/arm64/boot/dts/broadcom/<soc>/.
One idea to fix the issues in a clean way is to move DTB handling
to Kbuild core scripts. Makefile.dtbinst already recognizes dtb-y
natively, so it should not hurt to do so.
Add $(dtb-y) to extra-y, and $(dtb-) as well if CONFIG_OF_ALL_DTBS is
enabled. All clutter things in Makefiles go away.
As a bonus clean-up, I also removed dts-dirs. Just use subdir-y
directly to traverse sub-directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[robh: corrected BUILTIN_DTB to CONFIG_BUILTIN_DTB]
Signed-off-by: Rob Herring <robh@kernel.org>
We need to add "clean-files" in Makfiles to clean up DT blobs, but we
often miss to do so.
Since there are no source files that end with .dtb or .dtb.S, so we
can clean-up those files from the top-level Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Add the extended UART support on Armada 3700
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWgHNayMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71bHpAJ0QFOqPb3Et
NHXbvRjusO7ZZ+B6+wCff8at95p9E8X5ULnGpR7qINZHKh8=
=CdWu
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.15-2' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt64 for 4.15 (part 2)" from Gregory CLEMENT:
Add the extended UART support on Armada 3700
* tag 'mvebu-dt64-4.15-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: armada-3720-espressobin: fill UART nodes
arm64: dts: marvell: armada-3720-db: enable second UART port
arm64: dts: marvell: armada-37xx: add second UART port
arm64: dts: marvell: armada-37xx: add UART clock
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fill ESPRESSObin uart0 node with pinctrl information like in the
Armada-3720-DB device tree (which uses the same node).
Also explain how to enable the second UART port available on the
headers. This second port is not enabled by default because both
headers are dedicated to expose general purpose pins and remapping
some of them to use the second UART would break existing users.
Suggested-by: László ÁSHIN <laszlo@ashin.hu>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable Armada-3720-DB second UART port by adding the corresponding
device tree node in the board DTS and enabling it.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add a node in Armada 37xx DTSI file for the second UART, with a
different compatible due to its extended IP which has some
differences with the first UART already in place.
Make use of this commit to also fully describe the first port and
use the same clear and named interrupt bindings for both ports.
The standard UART (UART0) uses level-interrupts while the extended
UART (UART1) uses edge-triggered interrupts.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the missing clock property to armada-3700 UART node.
This clock will be used to derive the prescaler value to comply with
the requested baudrate.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
On Armada 7K/8k:
- Improve network support at SoC and board level
- Enable watchdog
- Add UART muxing
- On 7040 DB: add CD SDIO and NAND support
- On 8040 DB: add PCIE more ports and SPI1
On Armada 37xx:
- Fix UART register size
- Add vmmc regulator for SD on 3720 DB
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWeoPnCMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71eWeAJ4yqhFToGh9
bLvyANmN33Lp0kYfEwCeKTJv715mvxAfJMYUMX7CUmgEAOs=
=9sls
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.15-1' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt64 for 4.15 (part 1)" from Gregory CLEMENT:
On Armada 7K/8k:
- Improve network support at SoC and board level
- Enable watchdog
- Add UART muxing
- On 7040 DB: add CD SDIO and NAND support
- On 8040 DB: add PCIE more ports and SPI1
On Armada 37xx:
- Fix UART register size
- Add vmmc regulator for SD on 3720 DB
* tag 'mvebu-dt64-4.15-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: 7040-db: Add the carrier detect pin for SD card on CP
arm64: dts: marvell: 7040-db: Document the gpio expander
arm64: dts: marvell: enable additional PCIe ports on Armada 8040 DB
arm64: dts: marvell: add NAND support on the 7040-DB board
arm64: dts: marvell: Enable Armada-8040-DB CPS SPI1
arm64: dts: marvell: 8040-db: enable the SFP ports
arm64: dts: marvell: 7040-db: enable the SFP port
arm64: dts: marvell: 7040-db: add comphy reference to Ethernet port
arm64: dts: marvell: mcbin: add comphy references to Ethernet ports
arm64: dts: marvell: 37xx: remove empty line
arm64: dts: marvell: cp110: add PPv2 port interrupts
arm64: dts: marvell: add comphy nodes on cp110 master and slave
arm64: dts: marvell: extend the cp110 syscon register area length
arm64: dts: marvell: enable AP806 watchdog
arm64: dts: marvell: Fix A37xx UART0 register size
arm64: dts: marvell: armada-3720-db: Add vmmc regulator for SD slot
arm64: dts: marvell: add UART muxing on Armada 7K/8K
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm64/boot/dts -type -f -name '*.dts*'
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The SD card slot connected to the SD controller of the CP part has a
carrier detect pin connected the gpio expander. This patch enables it
allowing supporting the hotplug event for the SD card.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 8040 DB has numerous PCIe ports, so let's enable a few more
of those PCIe ports that are enabled in the default bootloader
configuration.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The interrupt-map property used in the description of the Marvell
Armada 7K/8K PCIe controllers has a bogus extraneous 0 that causes the
interrupt conversion to not be done properly. This causes the PCIe PME
and AER root port service drivers to fail their initialization:
[ 5.019900] genirq: Setting trigger mode 7 for irq 114 failed (irq_chip_set_type_parent+0x0/0x30)
[ 5.028821] pcie_pme: probe of 0001:00:00.0:pcie001 failed with error -22
[ 5.035687] genirq: Setting trigger mode 7 for irq 114 failed (irq_chip_set_type_parent+0x0/0x30)
[ 5.044614] aer: probe of 0001:00:00.0:pcie002 failed with error -22
This problem was introduced when the interrupt description was
switched from using the GIC directly to using the ICU interrupt
controller. Indeed, the GIC has address-cells = <1>, which requires a
parent unit address, while the ICU has address-cells = <0>.
Fixes: 6ef84a827c ("arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The NAND controller used in A7K/A8K is present on the CP110 master part.
It is compatible with the pxa3xx_nand driver but requires the use of the
marvell,armada-8k-nand compatible string due to the need to first enable
the NAND controller.
Add properties to the NAND node to fit the bindings constraints of the
pxa3xx_nand driver and enable the NAND controller.
Add the 'marvell,system-controller' property to the cp110 master NAND
node with a reference to the syscon node. This is new compared to other
boards using the pxa3xx_nand driver and it is needed to be bootloader
independent and enable the NAND controller from the NAND controller
driver itself by writing in these syscon registers.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
[miquel.raynal@free-electrons.com: add NAND ready/busy MPP subnode,
change compatible string to fit the needs of the A7k/A8k SoCs and add
the system controller property]
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
This patch enables the SFP ports on the Armada 8040 DB as these ports
are now supported by the PPv2 driver (since the PHY is now optional).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch enables the SFP port on the Armada 7040 DB as this port
is now supported by the PPv2 driver (since the PHY is now optional).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds a comphy phandle to the Ethernet port in the 7040-db
device tree. The comphy is used to configure the serdes PHYs used by
these ports.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds comphy phandles to the Ethernet ports in the mcbin
device tree. The comphy is used to configure the serdes PHYs used by
these ports.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cosmetic patch removing an empty line at the end of the NB pinctrl node.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Ports interrupts are used by the PPv2 driver when no PHY is connected to
a port. This patch adds a description of these interrupts.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch describes the comphy available in the cp110 master and slave.
This comphy provides serdes lanes used by various controllers such as
the network one.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch extends on both cp110 the system register area length to
include some of the comphy registers as well.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Extend the container size to 0x2000 to include the gpio controller at
offset 0x1040.
While at it, add start address notation to the gpio node name to match
its 'offset' property.
Fixes: 63dac0f492 ("arm64: dts: marvell: add gpio support for Armada
7K/8K")
Cc: <stable@vger.kernel.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Armada-37xx UART0 registers are 0x200 bytes wide. Right next to them are
the UART1 registers that should not be declared in this node.
Update the example in DT bindings document accordingly.
Signed-off-by: allen yan <yanwei@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
By adding this regulator, a proper reset is done during boot. Without
this, the UHS failed to be detected after a warm reboot when the SD card
remained in the slot, then it fallback to an HS.
Note that the vmcc is supported by the xenon driver only with the
following fix: "mmc: sdhci-xenon: add set_power callback".
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the relevant details in the Armada 7K/8K Device Tree
to properly mux the UART used for the serial console. Since there is
basically only one possible muxing for the UART0 on the AP, the muxing
configuration is described in armada-ap806.dtsi, and selected from the
individual boards (other boards could be using a different UART).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As usual, device tree updates is the bulk of our material in this merge
window. This time around, 559 patches affecting both 32- and 64-bit
platforms.
Changes are too many to list individually, but some of the larger ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also several
new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R45j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM/arm64 Devicetree updates from Olof Johansson:
"As usual, device tree updates is the bulk of our material in this
merge window. This time around, 559 patches affecting both 32- and
64-bit platforms.
Changes are too many to list individually, but some of the larger
ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also
several new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board"
* tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (559 commits)
ARM: dts: at91: at91sam9g45: add AC97
arm64: dts: marvell: mcbin: enable more networking ports
arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
arm64: dts: marvell: add TX interrupts for PPv2.2
arm64: dts: uniphier: add PXs3 SoC support
ARM: dts: uniphier: add pinctrl groups of ethernet phy mode
ARM: dts: uniphier: fix size of sdctrl nodes
ARM: dts: uniphier: add AIDET nodes
arm64: dts: uniphier: fix size of sdctrl node
arm64: dts: uniphier: add AIDET nodes
Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
arm64: dts: uniphier: add reset controller node of analog amplifier
arm64: dts: marvell: add Device Tree files for Armada-8KP
arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
dt-bindings: add rk3399-q7 SoM
ARM: dts: rockchip: enable usb for rv1108-evb
ARM: dts: rockchip: add usb nodes for rv1108 SoCs
dt-bindings: update grf-binding for rv1108 SoCs
ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
...
This patch enables the two GE/SFP ports. They are configured in 10GKR
mode by default. To do this the cpm_xdmio is enabled as well, and two
phy descriptions are added.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The network driver on Marvell SoC (7k/8k) needs to access some registers
in the system controller to configure its ports at runtime. This patch
adds a phandle reference to the syscon system controller node in the
ppv2 node.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit updates the Marvell Armada 7K/8K Device Tree to describe
the TX interrupts of the Ethernet controllers, in both the master and
slave CP110s.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the base Device Tree files for the Armada 8KPlus.
The Armada 8KP SoCs include several hardware blocks, and this
commit only adds support for the AP810 block, that contains the CPU
core and basic peripherals.
AP810 is a high-performance die, includes octal core application
processor based ARMv8-A architecture, two standard high speed DDR4
interface, and GIC-600 interrupt controller.
AP810 Built as part of Marvell’s MoChi AP family products.
Armada-8080 (8KPlus family), include an AP810 block that contains
the CPU core and basic peripherals.
This commit creates the following hierarchy:
* armada-ap810-ap0.dtsi - definitions common to AP810
* armada-ap810-ap0-octa-core.dtsi - description of the octa cores
* armada-8080.dtsi - description of the 8080 SoC
* armada-8080-db.dts - description of the 8080 board
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable USB host on Armada-8040-DB by adding USB PHY nodes for the
following ports:
- host 0 and 1 of CPM
- host 0 of CPS
These PHY are enabled by lanes coming from regulators based on two
I2C expanders.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add I2C expander and USB host PHY (host 0 and host 1) to enable
USB VBUS on USB ports of type A on Armada-7040-DB.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The NAND controller used in A7K/A8K is present on the CP110. It is
compatible with the pxa-nand driver.
However, due to the limiation of the pins available this controller is
only usable on the CPM for A7K and on the CPS for A8K.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The ESPRESSObin board exposes one of the SDHCI interfaces
via J1 uSD slot. This patch enables it.
Tested-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Zbigniew Bodek <zbodek@gmail.com>
[gregory.clement@free-electrons.com: removed "no-1-8-v"]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Since the introduction of the CP110 dt files, the sata node was
misplaced. Move it at the right place. Thanks to this, the files are
completely ordered.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
In both the CP110 master and slave description, the node describing
the RTC was at the wrong place when taking into account increasing
register addresses. Interestingly, it was not even at the same (wrong)
place in both files.
This commit adjusts that, making the master and slave descriptions
more aligned.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds an stdout-path to the mcbin device tree. This allows to
use earlycon.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add support for PCIe with the the PCIe reset signal wired up to the
appropriate GPIO pin.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
(excepted the reset part)
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The MACCHIATOBin board has a PCA9548 I2C mux for the SFP ports on
CP100 master I2C bus 1. Add the DT description for it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Due to the lack of GPIO support, the USB3 regulator definition was
left unfinished in the MacchiatoBin DT description. Now that GPIO
support is available, this commit adjusts the Device Tree to properly
describe the USB3 regulator.
[gregory.clement@free-electrons.com: use commit log from Thomas]
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add pinctrl nodes to describe the CPM I2C0 and CPS SPI1 settings.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the GPIO interrupts for the CP110.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Espressobin SBC has a USB2 interface available on J8. Let's
enable it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Cortex-A53s that power the Armada-37xx SoCs are equipped with
a PMUv3, just like most ARMv8 cores.
Advertise the PMUv3 presence in the device tree, and wire its
interrupt. This allows the perf subsystem to work correctly.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Cortex-A53s that power the Armada-37xx SoCs are equipped with
a GIC CPU interface that gets enabled when coupled with a GICv3
interrupt controller, such as the GIC-500 on the this SoC.
Advertise the MMIO ranges provided by the CPUs, which enables
(among other things) GICv2 guests to run under a hypervisor such
as KVM.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The GIC-500 integrated in the Armada-37xx SoCs is compliant with
the GICv3 architecture, and thus provides a maintenance interrupt
that is required for hypervisors to function correctly.
With the interrupt provided in the DT, KVM now works as it should.
Tested on an Espressobin system.
Fixes: adbc3695d9 ("arm64: dts: add the Marvell Armada 3700 family and
a development board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The number of pins in South Bridge is 30 and not 29. There is a fix for
the driver for the pinctrl, but a fix is also need at device tree level
for the GPIO.
Fixes: afda007fed ("ARM64: dts: marvell: Add pinctrl nodes for Armada
3700")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The crypto engines found on the cp110 master and slave are dma coherent.
This patch adds the relevant property to their dt nodes.
Cc: stable@vger.kernel.org # v4.12+
Fixes: 973020fd94 ("arm64: marvell: dts: add crypto engine description for 7k/8k")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
When the conversion of the Marvell CP110 Device Tree description from
using GIC interrupts to using ICU interrupts was done, the RTC on the
slave CP110 was left unchanged. This commit fixes that, so that all
devices on the CP properly get their interrupt through the ICU.
Fixes: 6ef84a827c ("arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
It is actually a patch that missed the end of the 4.12 merge
window. The patch itself fix a bogus definition of the timer for the
Armada 37xx SoCs.
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWVpGxCMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71SGMAKCP9mGjMWqD
Z9uCT8swDJ8LCi/o+wCfV4Cs0eWzqkJUDMaycdJrlMjB174=
=TavE
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.13-3' of git://git.infradead.org/linux-mvebu into next/dt64
Pull "late dt64 for 4.13" from Gregory CLEMENT:
It is actually a patch that missed the end of the 4.12 merge
window. The patch itself fix a bogus definition of the timer for the
Armada 37xx SoCs.
* tag 'mvebu-dt64-4.13-3' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: armada37xx: Fix timer interrupt specifiers
Contrary to popular belief, PPIs connected to a GICv3 to not have
an affinity field similar to that of GICv2. That is consistent
with the fact that GICv3 is designed to accomodate thousands of
CPUs, and fitting them as a bitmap in a byte is... difficult.
Fixes: adbc3695d9 ("arm64: dts: add the Marvell Armada 3700 family and
a development board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As I found by chance while merging another patch, the usage of
a dma-mask in this DT node is wrong for multiple reasons:
- dma-masks are a Linux specific concept, not a general
hardware feature
- In DT, we use the "dma-ranges" property to describe how DMA
addresses related between devices.
- The 40-bit mask appears to be completely unnecessary here, as
the SoC cannot address that much memory anyway, so simply
asking for a 64-bit mask (as supported by the device) should
succeed anyway.
The patch to remove the parsing of the property is getting merged
through the crypto tree.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix the interrupt description of the crypto node for device tree of
the Armada 7K/8K SoCs
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWTAszCMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71bcsAJ4kcIDc5FwI
e9qfRomziu3A+S6K0QCfX3Ii7XGH1fANfeTCAnyZGXmYFZI=
=wjTT
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.12-1' of git://git.infradead.org/linux-mvebu into next/dt64
mvebu fixes for 4.12
Fix the interrupt description of the crypto node for device tree of
the Armada 7K/8K SoCs
* tag 'mvebu-fixes-4.12-1' of git://git.infradead.org/linux-mvebu:
arm64: marvell: dts: fix interrupts in 7k/8k crypto nodes
This commit modifies the Marvell EBU Armada 7K and 8K Device Tree files
to describe the ICU and GICP units, and use ICU interrupts for all
devices in the CP110 blocks.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable gpio support for CP and AP on the Marvell Armada 7K/8K SoCs.
The Armada 8K has two CP110 blocks, each having two GPIO controllers.
However, in each CP110 block, one of the GPIO controller cannot be
used: in the master CP110, only the second GPIO controller can be used,
while on the slave CP110, only the first GPIO controller can be used.
On the other side, the Armada 7K has only one CP110, but both its GPIO
controllers can be used.
For this reason, the GPIO controllers are marked as "disabled" in the
armada-cp110-master.dtsi and armada-cp110-slave.dtsi files, and only
enabled in the per-SoC dtsi files.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable pinctrl support for CP and AP on the Armada 7K/8K SoCs.
The CP master being different between Armada 7k and Armada 8k. This
commit introduces the intermediates files armada-70x0.dtsi and
armada-80x0.dtsi.
These new files will provide different compatible strings depending of
the SoC family. They will also be the location for the pinmux
configuration at the SoC level.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The new binding for the system controller on cp110 moved the clock
controller into a subnode. This preliminary step will allow to add gpio
and pinctrl subnodes.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The *-clock-output-names of the cp110-system-controller0 node are not
used anymore, so remove them.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
New bindings are used for the system controller on the ap806, which
means all clock properties must be converted. Use the new bindings in
the xor nodes.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Since the mdio nodes are disabled by default now, we should explicitly
enable these nodes at the board level when they are used. Enable the
cpm_mdio node for the 8040-mcbin.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the description of the xMDIO bus for the Marvell Armada 7k and
Marvell Armada 8k; for both CP110 slave and master. This bus is found
on Marvell Ethernet controllers and provides an interface with the
xMDIO bus.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The cryptographic engine found on the cp110 slave is disabled by default
because of some known limitations. Add a comment to explain why it is
disabled by default.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The cryptographic engine on the master cp110 is now enabled by default
at the SoC level. Remove its dts nodes that were only enabling it.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable the cryptographic engine at the SoC level on the master cp110.
This engine is always present and do not depends on any pinmux
configuration.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
By adding this regulator, the SD cards are usable at higher speed
protocols such as SDR104.
This patch was tested with an SD HC card compatible with UHS-I.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 37xx SoCs has 2 SDHCI interfaces. This patch adds the second
one.
Moreover, the Armada 37xx DB v2 board populates the 2 SDHCI interfaces.
The second interface is using pluggable module that can either
have an SD connector or eMMC on it.
This patch adds support for SD module in the device DT.
[ gregory.clement@free-electrons.com:
- Add more detail in commit log
- Sort the dt node in address order
- Document the SD slot in the dts ]
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
When several groups of register address and size are used with reg, then
surround each one by angle bracket.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The initial device tree file was for the board V1.4. Now the V2.0 board
is also available. The same dtb will work for both, but the CON number
have changed, so update the comment in the dts to reflect this.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Sort the reference nodes in alphabetical order to ease the merge of
future nodes.
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Disable the mdio nodes by default in the cp110 slave and master dtsi as
they're not wired on every board.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Explicitly enable the MDIO nodes in the Marvell Armada 7k DB and Marvell
Armada 8k DB. This is needed as the MDIO nodes will be disabled in the
CP 110 slave and master dtsi by a following up patch.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The EIP197 cryptographic engine supports 64 bits address width but is
limited to 40 bits on 7k/8k. Add a dma-mask property in the
cryptographic engine nodes to reflect this.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable the 1GB Ethernet interface that lives on the slave CP110,
with its corresponding phy (that oddly lives on the master CP110).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the three required clocks for the MDIO interface to be functional
on Armada 8k platforms. Without this, the CPU hangs, causing RCU
stalls or the system to become unresponsive.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[Thomas:
- remove mg_core_clock, since it's a parent of mg_clock
- also add clock references to the slave CP mdio instance]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The new binding for the system controller on ap806 moved the clock into a
subnode. This preliminary step will allow to add gpio and pinctrl
subnodes
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The clock-output-names of the ap806-system-controller node are not used
anymore, so remove them.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Armada 8040 DB is equipped with 4 (2x 10G SFI + 2x 1G RGMII)
ethernet ports of which only one was hitherto enabled.
Because currently mvpp2 driver is capable of supporting only
1G RGMII/SGMII, enable second port from CP slave HW block.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add sdhci support for MACCHIATOBin boards. This uses the AP806 SDHCI
for eMMC and CP110 master for the SD card slot.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The XORv2 engines in the AP side of the Armada 7K/8K SoCs are using the
AP MS core clock as input, so this commit adds the appropriate clocks
properties.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The cryptographic engine nodes have an interrupt which is configured as
both edge and level, which makes no sense at all. Fix this by
configuring it the right way (level).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
pinctrl and GPIO description for Armada 37xx SoCs
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWQNYziMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71cGmAJ4yR6i1f8EZ
25RXPzm/6ubxAYiRMgCfWVjipw6KD0s2muMylnk8ppz4PaM=
=NOR2
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.12-3' of git://git.infradead.org/linux-mvebu into fixes
Pull "mvebu dt64 for 4.12 (part 3)" from Gregory CLEMENT:
pinctrl and GPIO description for Armada 37xx SoCs
* tag 'mvebu-dt64-4.12-3' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: armada37xx: add pinctrl definition
ARM64: dts: marvell: Add pinctrl nodes for Armada 3700
Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch of smaller
changes, but also some new platforms that are worth mentioning:
* Rockchip RK3399 platforms for Chromebooks, including Samsung Chromebook
Plus (Kevin)
* Orange Pi PC2 (Allwinner H5)
* Freescale LS2088A and LS1088A SoCs
* Expanded support for Nvidia Tegra186 (and Jetson TX2)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=q3Ix
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Olof Johansson:
"Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch
of smaller changes, but also some new platforms that are worth
mentioning:
- Rockchip RK3399 platforms for Chromebooks, including Samsung
Chromebook Plus (Kevin)
- Orange Pi PC2 (Allwinner H5)
- Freescale LS2088A and LS1088A SoCs
- Expanded support for Nvidia Tegra186 (and Jetson TX2)"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (180 commits)
arm64: dts: Add basic DT to support Spreadtrum's SP9860G
arm64: dts: exynos: Use - instead of @ for DT OPP entries
arm64: dts: exynos: Add support for s6e3hf2 panel device on TM2e board
arm64: dts: juno: add information about L1 and L2 caches
arm64: dts: juno: fix few unit address format warnings
arm64: marvell: dts: enable the crypto engine on the Armada 8040 DB
arm64: marvell: dts: enable the crypto engine on the Armada 7040 DB
arm64: marvell: dts: add crypto engine description for 7k/8k
arm64: dts: marvell: add sdhci support for Armada 7K/8K
arm64: dts: marvell: add eMMC support for Armada 37xx
arm64: dts: hisi: add pinctrl dtsi file for HiKey960 development board
arm64: dts: hisi: add drive strength levels of the pins for Hi3660 SoC
arm64: dts: hisi: enable the NIC and SAS for the hip07-d05 board
arm64: dts: hisi: add SAS nodes for the hip07 SoC
arm64: dts: hisi: add RoCE nodes for the hip07 SoC
arm64: dts: hisi: add network related nodes for the hip07 SoC
arm64: dts: hisi: add mbigen nodes for the hip07 SoC
arm64: dts: rockchip: fix the memory size of PX5 Evaluation board
arm64: dts: hisilicon: add dts files for hi3798cv200-poplar board
dt-bindings: arm: hisilicon: add bindings for hi3798cv200 SoC and Poplar board
...
Here is the big USB patchset for 4.12-rc1.
Lots of good stuff here, after many many many attempts, the kernel
finally has a working typeC interface, many thanks to the Heikki and
Guenter and others who have taken the time to get this merged. It
wasn't an easy path for them at all.
There's also a staging driver that uses this new api, which is why it's
coming in through this tree.
Along with that, there's the usual huge number of changes for gadget
drivers, xhci, and other stuff. Johan also finally refactored pretty
much every driver that was looking at USB endpoints to do it in a common
way, which will help prevent any "badly-formed" devices from causing
problems in drivers. That too wasn't a simple task.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQvEIQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yny4gCePCXxnrQdMWE+IMXf1H1hMubLkVkAn0ZWgQkq
BspgO7ZmGb+9Fpf6YvNz
=nwAu
-----END PGP SIGNATURE-----
Merge tag 'usb-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB patchset for 4.12-rc1.
Lots of good stuff here, after many many many attempts, the kernel
finally has a working typeC interface, many thanks to Heikki and
Guenter and others who have taken the time to get this merged. It
wasn't an easy path for them at all.
There's also a staging driver that uses this new api, which is why
it's coming in through this tree.
Along with that, there's the usual huge number of changes for gadget
drivers, xhci, and other stuff. Johan also finally refactored pretty
much every driver that was looking at USB endpoints to do it in a
common way, which will help prevent any "badly-formed" devices from
causing problems in drivers. That too wasn't a simple task.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
staging: typec: Fairchild FUSB302 Type-c chip driver
staging: typec: Type-C Port Controller Interface driver (tcpci)
staging: typec: USB Type-C Port Manager (tcpm)
usb: host: xhci: remove #ifdef around PM functions
usb: musb: don't mark of_dev_auxdata as initdata
usb: misc: legousbtower: Fix buffers on stack
USB: Revert "cdc-wdm: fix "out-of-sync" due to missing notifications"
usb: Make sure usb/phy/of gets built-in
USB: storage: e-mail update in drivers/usb/storage/unusual_devs.h
usb: host: xhci: print correct command ring address
usb: host: xhci: delete sp_dma_buffers for scratchpad
usb: host: xhci: using correct specification chapter reference for DCBAAP
xhci: switch to pci_alloc_irq_vectors
usb: host: xhci-plat: set resume_quirk() for R-Car controllers
usb: host: xhci-plat: add resume_quirk()
usb: host: xhci-plat: enable clk in resume timing
usb: host: plat: Enable xHCI plat runtime PM
USB: serial: ftdi_sio: add device ID for Microsemi/Arrow SF2PLUS Dev Kit
USB: serial: constify static arrays
usb: fix some references for /proc/bus/usb
...
Start to populate the device tree of the Armada 37xx with the pincontrol
configuration used on the board providing a dts.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the nodes for the two pin controller present in the Armada 37xx SoCs.
Initially the node was named gpio1 using the same name that for the
register range in the datasheet. However renaming it pinctr_nb (nb for
North Bridge) makes more sens.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add fixed clock of 400MHz to system controller driver. This clock is
used as SD/eMMC clock source.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Omri Itach <omrii@marvell.com>
Reviewed-by: Hanna Hawa <hannah@marvell.com>
[fixed up conflicts, added error handling --rmk]
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable the cryptographic engine available in the CP110 master on the
Armada 8040 DB. Do not enable the one in the CP110 salve for now, as we
do not support multiple cryptographic engines yet.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable the cryptographic engine available in the CP110 master on the
Armada 7040 DB.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the description of the crypto engine hardware block for the Marvell
Armada 7k and Armada 8k processors; for both the CP110 slave and master.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the eMMC support for Armada 37xx SoC and enable it in the Armada 3720
DB board.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the description of the PPv2.2 hardware block for the
Marvell Armada 7K and Armada 8K processors, and their corresponding Armada
7040 and 8040 Development boards.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 3720 DB board has an RTC on the I2C bus. It's a PT7C4337A from
Pericom but which claims to be fully compatible with the ds1337.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Now that the gpio expander is present in the dts, use it to add an USB3
PHY using one of these gpio as a regulator.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Armada 37xx SoC embedded an EHCI controller. This patch adds the device
tree node enabling its support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A gpio expander is present on the i2c bus on the Armada 3720 DB board. This
patch add it to the device tree.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
These property were missing when the nodes were added and their lack
generate warning messages when adding i2c device in the subnodes.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This RTC IP is found in the CP110 master and slave which are part of the
Armada 8K SoCs and of the subset family the Armada 7K.
There is one RTC in each CP but the RTC requires an external
oscillator. However on the Armada 80x0, the RTC clock in CP master is not
connected (by package) to the oscillator. So this one is disabled for the
Armada 8020 and the Armada 8040.
As the RTC clock in CP slave is connected to the oscillator this one is
let enabled. and will be used on these SoCs (80x0).
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adjusts the names of gatable clock #18 of the Marvell Armada
CP110 system controller. This clock not only controls SD/MMC, but also
the GOP (Group Of Ports) used for networking. So the clock is renamed to
{cpm,cps}-sd-mmc-gop instead of {cpm,cps}-sd-mmc.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Testing with an Armada 8040 board shows that adding the generic-ahci
compatible to the CP110 AHCI nodes gets us working AHCI on the board.
A previous patch series posted by Thomas Petazzoni was retracted when
it was realised that the IP was supposed to be, and is, compatible
with the standard register layout.
Add this compatible.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add a cut-down version of the DTS file for the community board
MACCHIATOBin from SolidRun based on Marvell Armada 8040 SoC to suit
the current mainlined Armada 8040 state.
This brings support for mainly SATA, SPI flash and UART. The USB
descriptions are included but are not tested in this form due to the
lack of mainline GPIO.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Acked-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The license text has been mangled at some point then copy pasted across
multiple files. Restore it to what it should be.
Note that this is not intended as a license change.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 3700 has two i2c bus interface units, this commit adds the
definitions of the corresponding device nodes. It also enables the node
on the development board for this SoC.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit enables the device node spi0 on the official development
board for the Marvell Armada 3700. It also adds sub-node for the 128Mb
SPI-NOR present on the board.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Armada 3700 SoC has an SPI Controller, this commit adds the definition
of the SPI device node at the SoC level.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This defines and enables the Marvell ethernet switch MVE886341 on the
Marvell ESPRESSObin board.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
A couple of interesting new SoC platforms are now supported, these are
the respective DTS sources:
- Samsung Exynos5433 mobile phone platform, including an (almost) fully
supported phone reference board.
- Hisilicon Hip07 server platform and D05 board, the latest iteration
of their product line, now with 64 Cortex-A72 cores across two
sockets.
- Allwinner A64 SoC, the first 64-bit chip from their "sunxi" product
line, used in Android tablets and ultra-cheap development boards
- NXP LS1046A Communication processor, improving on the earlier LS1043A
with faster CPU cores
- Qualcomm MSM8992 (Snapdragon 808) and MSM8994 (Snapdragon 810)
mobile phone SoCs
- Early support for the Nvidia Tegra Tegra186 SoC
- Amlogic S905D is a minor variant of their existing Android consumer
product line
- Rockchip PX5 automotive platform, a close relative of their popular
rk3368 Android tablet chips
Aside from the respective evaluation platforms for the above
chips, there are only a few consumer devices and boards added
this time:
- Huawei Nexus 6P (Angler) mobile phone
- LG Nexus 5x (Bullhead) mobile phone
- Nexbox A1 and A95X Android TV boxes
- Pine64 development board based on Allwinner A64
- Globalscale Marvell ESPRESSOBin community board based on Armada 3700
- Renesas "R-Car Starter Kit Pro" (M3ULCB) low-cost automotive board
For the existing platforms, we get bug fixes and new peripheral support
for Juno, Renesas, Uniphier, Amlogic, Samsung, Broadcom, Rockchip, Berlin,
and ZTE.
Conflicts:
- Documentation/devicetree/bindings/arm/shmobile.txt: a
rename/add conflict, keep both modifications and maintain
alphabetical ordering.
- arch/arm64/boot/dts/*/*.dtsi: nodes were added in netdev,
mmc and clk, keep both sides in each case.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=geT0
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"A couple of interesting new SoC platforms are now supported, these are
the respective DTS sources:
- Samsung Exynos5433 mobile phone platform, including an (almost)
fully supported phone reference board.
- Hisilicon Hip07 server platform and D05 board, the latest iteration
of their product line, now with 64 Cortex-A72 cores across two
sockets.
- Allwinner A64 SoC, the first 64-bit chip from their "sunxi" product
line, used in Android tablets and ultra-cheap development boards
- NXP LS1046A Communication processor, improving on the earlier
LS1043A with faster CPU cores
- Qualcomm MSM8992 (Snapdragon 808) and MSM8994 (Snapdragon 810)
mobile phone SoCs
- Early support for the Nvidia Tegra Tegra186 SoC
- Amlogic S905D is a minor variant of their existing Android consumer
product line
- Rockchip PX5 automotive platform, a close relative of their popular
rk3368 Android tablet chips
Aside from the respective evaluation platforms for the above chips,
there are only a few consumer devices and boards added this time:
- Huawei Nexus 6P (Angler) mobile phone
- LG Nexus 5x (Bullhead) mobile phone
- Nexbox A1 and A95X Android TV boxes
- Pine64 development board based on Allwinner A64
- Globalscale Marvell ESPRESSOBin community board based on Armada 3700
- Renesas "R-Car Starter Kit Pro" (M3ULCB) low-cost automotive board
For the existing platforms, we get bug fixes and new peripheral
support for Juno, Renesas, Uniphier, Amlogic, Samsung, Broadcom,
Rockchip, Berlin, and ZTE"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (168 commits)
arm64: dts: fix build errors from missing dependencies
ARM64: dts: meson-gxbb: add SCPI pre-1.0 compatible
ARM64: dts: meson-gxl: Add support for Nexbox A95X
ARM64: dts: meson-gxm: Add support for the Nexbox A1
ARM: dts: artpec: add pcie support
arm64: dts: berlin4ct-dmp: add missing unit name to /memory node
arm64: dts: berlin4ct-stb: add missing unit name to /memory node
arm64: dts: berlin4ct: add missing unit name to /soc node
arm64: dts: qcom: msm8916: Add ddr support to sdhc1
arm64: dts: exynos: Enable HS400 mode for eMMC for TM2
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM64: dts: Add support for Meson GXM
dt-bindings: add rockchip RK1108 Evaluation board
arm64: dts: NS2: Add PCI PHYs
arm64: dts: NS2: enable sdio1
arm64: dts: exynos: Add the mshc_2 node for supporting T-Flash
arm64: tegra: Add NVIDIA P2771 board support
arm64: tegra: Enable PSCI on P3310
arm64: tegra: Add NVIDIA P3310 processor module support
arm64: tegra: Add GPIO controllers on Tegra186
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.10:
API:
- add skcipher walk interface
- add asynchronous compression (acomp) interface
- fix algif_aed AIO handling of zero buffer
Algorithms:
- fix unaligned access in poly1305
- fix DRBG output to large buffers
Drivers:
- add support for iMX6UL to caam
- fix givenc descriptors (used by IPsec) in caam
- accelerated SHA256/SHA512 for ARM64 from OpenSSL
- add SSE CRCT10DIF and CRC32 to ARM/ARM64
- add AEAD support to Chelsio chcr
- add Armada 8K support to omap-rng"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (148 commits)
crypto: testmgr - fix overlap in chunked tests again
crypto: arm/crc32 - accelerated support based on x86 SSE implementation
crypto: arm64/crc32 - accelerated support based on x86 SSE implementation
crypto: arm/crct10dif - port x86 SSE implementation to ARM
crypto: arm64/crct10dif - port x86 SSE implementation to arm64
crypto: testmgr - add/enhance test cases for CRC-T10DIF
crypto: testmgr - avoid overlap in chunked tests
crypto: chcr - checking for IS_ERR() instead of NULL
crypto: caam - check caam_emi_slow instead of re-lookup platform
crypto: algif_aead - fix AIO handling of zero buffer
crypto: aes-ce - Make aes_simd_algs static
crypto: algif_skcipher - set error code when kcalloc fails
crypto: caam - make aamalg_desc a proper module
crypto: caam - pass key buffers with typesafe pointers
crypto: arm64/aes-ce-ccm - Fix AEAD decryption length
MAINTAINERS: add crypto headers to crypto entry
crypt: doc - remove misleading mention of async API
crypto: doc - fix header file name
crypto: api - fix comment typo
crypto: skcipher - Add separate walker for AEAD decryption
..
Add neta nodes for network support both in device tree for the SoC and
the board.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix some dtc compiler warnings
-----BEGIN PGP SIGNATURE-----
iQJIBAABCAAyFiEE2MW6uuYZ+0zBfpF41kg+k28NbwgFAlg4AYgUHGpzemhhbmdA
bWFydmVsbC5jb20ACgkQ1kg+k28Nbwgagw//V2xn6tlMIniGrEFjeePy3EQs3EpJ
AKzJ4/XvJItN5cheNbg4aoCLMa6LZuz7P0LhwcIxm1v9pIgx0qBhsElS6UuDpUs8
XszCryYtpkFmT3MHsRX5qU2zPjHsQn5MqIi0V4SQeEc/ELSZAaroqiC85bjo8Qoy
jYccHVPxwmdFZbIuNQNyg+GalpEyHo3jbOumc07dcf7z9zup3y2oknBJ+19v9Cs2
7zl9/i4SOlRQfXBTyYqmz5aAsAvffMSEYDmXdwLirZHr3W5ZCbg791NLG72MxeKl
iuLKvNbNUyumiUxVAKey4V1Yqa75w2JyDMNpy0yrmbgukD1zR48MLg3Zak9wvuJH
i9F3Iwd4+WiwihA+ulVwDYLICf/xofV+6CcxXSveHKnn8UFHK8qpdjTX0NAxTi94
61epxAmubpQ/mbLtrH0nJiJP6RvghvZHjz7gDRFvPapSefSU8hEM/RI39o9U20hR
vYDFLb0m9WYhJvuBXgXVM7gbDQPrErQwyL+/SEtIrjnnHt74V4iPhECm7m8fTgL7
1zFj4Vq2iwsNyy0vEPINzxc0hlmYVzwpKKaMof5HdyR5a7vqm6KsmozDBavyLOar
dYTrZeIUqmtwozBUHdpVQv/DKRs1IcjNuMM3uKEurQMfgIj2gRKCKOJghVgs9xSu
fgqkBWEkW6ad3yM=
=JqjI
-----END PGP SIGNATURE-----
Merge tag 'berlin64-dt-for-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin into next/dt64
Pull "Berlin64 DT changes for v4.10" from Jisheng Zhang:
- fix some dtc compiler warnings
* tag 'berlin64-dt-for-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin:
arm64: dts: berlin4ct-dmp: add missing unit name to /memory node
arm64: dts: berlin4ct-stb: add missing unit name to /memory node
arm64: dts: berlin4ct: add missing unit name to /soc node
Fix DTC warning on Armada 37xx and 7K/8K
-----BEGIN PGP SIGNATURE-----
iGkEABECACoFAlgwEHAjHGdyZWdvcnkuY2xlbWVudEBmcmVlLWVsZWN0cm9ucy5j
b20ACgkQCwYYjhRyO9VIzACgpB+IM/uM1EMD3IUQM3Wk8TodfwQAmLUWZdt1at2+
VU9vmax2KRbR00I=
=K7yX
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.10-2' of git://git.infradead.org/linux-mvebu into next/dt64
Pull "mvebu dt64 for 4.10 (part 2)" from Gregory CLEMENT:
Fix DTC warning on Armada 37xx and 7K/8K
* tag 'mvebu-dt64-4.10-2' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: Fixup memory DT warning for Armada 37xx
arm64: dts: marvell: Fixup config-space DT warning For Armada 7K/8K
arm64: dts: marvell: Fixup internal-regs DT warning for Armada 37xx
This patch fixes the following DTC warning with W=1:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
This patch fixes the following DTC warning with W=1:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
This patch fixes the following DTC warning with W=1:
"Node /soc has a reg or ranges property, but no unit name"
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
