"marvell,armada3700" is not a documented compatible value. According to
the schema, "marvell,armada3720" SoCs should have a "marvell,armada3710"
fallback compatible.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The Espressobin Ultra DTS includes Espressobin DTSI which defines
ethernet-switch@1 node. The Ultra DTS overrides "reg" to 3, but that
leaves still old unit address which conflicts with the new phy@1 node
(W=1 dtc warning):
armada-3720-espressobin.dtsi:148.29-203.4: Warning (unique_unit_address_if_enabled): /soc/internal-regs@d0000000/mdio@32004/ethernet-switch@1: duplicate unit-address (also used in node /soc/internal-regs@d0000000/mdio@32004/ethernet-phy@1)
Fix this by deleting ethernet-switch@1 node and merging original node
with code from Ultra DTS into new ethernet-switch@3.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Fix some errors in the Marvell MV88E6xxx switch descriptions:
- The top node had no address size or cells.
- switch0@0 is not OK, should be ethernet-switch@0.
- ports should be ethernet-ports
- port@0 should be ethernet-port@0
- PHYs should be named ethernet-phy@
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Boot hangs on EspressoBIN Ultra (Armada 3720) after a message that device
vcc_sd1 had been disabled. The device manufacturer patched this issue in
their kernel fork noting that vcc_sd1 is used by the EspressoBIN model
but not the EspressoBIN Ultra. Removing the device from the tree fixes
the boot hang and wifi.
Signed-off-by: Ben Schneider <ben@bens.haus>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
All Armada 3720 boards have Armada 3720 processor which is of Armada 3700
family and do not have Armada 3710 processor. So none of them should have
compatible string for Armada 3710 processor.
Fix compatible string for all these boards by removing wrong processor
string "marvell,armada3710" and adding family string "marvell,armada3700"
as the last one. (Note that this is same way how are defined Armada 3710
DTS files).
[gclement: fix conflict for v6.2]
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Espressobin Ultra is part of the Espressobin family and shares the basic
design, so add the generic "globalscale,espressobin" compatible to it as
well.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Espressobin Ultra has a front panel USB3.0 Type-A port which works
just fine so enable it.
I dont see a reason why it was disabled in the first place anyway.
Fixes: 3404fe15a6 ("arm64: dts: marvell: add DT for ESPRESSObin-Ultra")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Both the Topaz switch and 88E1512 PHY have their reset and interrupts
connected to the SoC.
So, define the Topaz and 88E1512 reset pins in the DTS.
Defining the interrupt pins wont work as both the 88E1512 and the
Topaz switch uses active LOW IRQ signals but the A37xx GPIO controller
only supports edge triggers.
88E1512 would require special setup anyway as its INT pin is shared with
the LED2 and you first need to configure it as INT.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
SPI config for the SPI-NOR is incorrect and completely breaking
reading/writing to the onboard SPI-NOR.
SPI-NOR is connected in the single(x1) IO mode and not in the quad
(x4) mode.
Also, there is no need to override the max frequency from the DTSI
as the mx25u3235f that is used supports 104Mhz.
Fixes: 3404fe15a6 ("arm64: dts: marvell: add DT for ESPRESSObin-Ultra")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This adds support for ESPRESSObin-Ultra from Globalscale.
Specifications are similar to the base ESPRESSObin board, with main
difference being being WAN port with PoE capability and 2 additional ethernet ports.
Full specifications:
1x Marvell 64 bit Dual Core ARM A53 Armada 3700 SOC clocked up to 1.2Ghz
1x Topaz 6341 Networking Switch
1GB DDR4
8GB eMMC
1x WAN with 30W POE
4x Gb LAN
1x RTC Clock and battery
1x DC Jack
1x USB 3.0 Type A
1x USB 2.0 Type A
1x SIM NanoSIM card Slot
1x Power Button
4x LED
1x Reset button
1x microUSB for UART
1x M.2 2280 slot for memory
1x 2x2 802.11ac Wi-Fi
1x MiniPCIE slot for Wi-Fi (PCIe interface)
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
