Add operating points for A64. These are taken from FEX file from BSP
for A64.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Add cooling maps and thermal tripping points to prevent CPU overheating when
running at the highest frequency. Tripping points are taken from A33 dts since
A64 user manual doesn't mention when we should start throttling.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Add CPU clock to the CPU nodes since it is a prerequisite for enabling
DVFS.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
[wens@csie.org: Replace CLK_CPUX macro with raw number]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
A few clocks from the CCU were exported later, and references to them in
the device tree were using raw numbers.
Now that the DT binding header changes are in as well, switch to the
macros for more clarity.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The Libre Computer ALL-H5-CC board is an upgraded version of the
ALL-H3-CC. Changes include:
- Gigabit Ethernet via external RTL8211E Ethernet PHY
- 16 MiB SPI NOR flash memory
- PoE tap header
- Line out jack removed
Only H5 variant test samples were made available, and the vendor is not
certain whether other SoC variants would be made or not. Furthermore the
board is a minor upgrade compared to the ALL-H3-CC. Thus the device tree
simply includes the one for the ALL-H3-CC, and adds the changes on top.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
By default, gpio-keys configures the pin to trigger wakeup IRQs on
either edge. The lid switch should only trigger wakeup when opening the
lid, not when closing it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
There are two sensors, one for CPU, one for GPU.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The Libre Computer ALL-H3-IT board is a small single board computer that
is roughly the same size as the Raspberry Pi Zero, or around 20% smaller
than a credit card.
The board features:
- H2, H3, or H5 SoC from Allwinner
- 2 DDR3 DRAM chips
- Realtek RTL8821CU based WiFi module
- 128 Mbit SPI-NOR flash
- micro-SD card slot
- micro HDMI video output
- FPC connector for camera sensor module
- generic Raspberri-Pi style 40 pin GPIO header
- additional pin headers for extra USB host ports, ananlog audio and
IR receiver
Only H5 variant test samples were made available, but the vendor does
have plans to include at least an H3 variant. Thus the device tree is
split much like the ALL-H3-CC, with a common dtsi file for the board
design, and separate dts files including the common board file and the
SoC dtsi file. The other variants will be added as they are made
available.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Add MIPI DSI pipeline for Allwinner A64.
- dsi node, with A64 compatible since it doesn't support
DSI_SCLK gating unlike A33
- dphy node, with A64 compatible with A33 fallback since
DPHY on A64 and A33 is similar
- finally, attach the dsi_in to tcon0 for complete MIPI DSI
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
A64 has 3 thermal sensors: 1 for CPU, 2 for GPU.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
There are two sensors, one for CPU, one for GPU.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Allwinner device tree files used different comment style for
copyright notice.
Update this to keep a coherency.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Use a shorter SPDX identifier instead of pasting the
whole license.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Some headers specify that files are under dual-licensed GPL2.0+
and X11. But in fact, it turns out that the full licenses texts
associated are GPL2.0+ and MIT.
Fix license headers to reflect real licenses associated.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
With dual licensed SPDX identifier the "OR" should
be uppercase.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Allwinner A64 SoC has separate supplies for PC, PD, PE, PG and PL. This
patch adds regulators for them to the pinctrl node.
Exception is PL which is used by the RSB bus. To avoid circular
dependencies, VCC-PL is omitted.
On boards with eMMC, VCC-PC is supplied by ELDO1, instead of DCDC1.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
[Maxime: Changed the r_pio comment a bit]
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Allwinner H6 PWM is similar to that in A20 except that it has additional
bus clock and reset line.
Note that first PWM channel is connected to output pin and second
channel is used internally, as a clock source to AC200 co-packaged chip.
This means that any combination of these two channels can be used and
thus it doesn't make sense to add pinctrl nodes at this point.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Add the Performance Monitoring Unit (PMU) device tree node to the H5
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core.
As with the A64, the interrupt numbers from the manual were wrong (off
by 4), the actual SPI IDs have been gathered in U-Boot, and were
verified with perf in Linux.
Tested with perf record and taskset on an OrangePi PC2.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Add the Performance Monitoring Unit (PMU) device tree node to the H6
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core. The numbers come from the manual and have
been checked in U-Boot and with perf in Linux.
Tested with perf record and taskset on a Pine H64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tanix TX6 box comes with a remote. Add a mapping for it.
Suggested-by: Michael Lange <linuxstuff@milaw.biz>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This patch adds the model B of the PineH64.
The model B is smaller than the pine64 model A and has no PCIE slot.
The only devicetree difference with the pineH64 model A, is the PHY
regulator and the HDMI connector node.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current sun50i-h6-pine-h64 DT does not specify which model (A or B)
it supports.
When this file was created, only modelA was existing, but now both model
exists and with the time, this DT drifted to support the model B since it is
the most common one.
Furtheremore, some part of the model A does not work with it like ethernet and
HDMI connector (as confirmed by Jernej on IRC).
So it is time to settle the issue, and the easiest way was to state that
this DT is for model B.
Easiest since only a small name changes is required.
Doing the opposite (stating this file is for model A) will add changes (for
ethernet and HDMI) and so, will break too many setup.
But as asked by the maintainer this patch state this file is for model A.
In the process this patch adds the missing compoments to made it work on
model A.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
A new variant of Emlid Neutis has been inroduced. This one uses H3
instead of H5. The boards are essentially the same. This commit moves
non-SoC-specific parts out so that the common parts could be reused with
ease.
Signed-off-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Enable USB 3.0 phy and host controller.
VBUS is directly connected to DCIN 5V and doesn't
require to be switched on.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Orange Pi 3 has an on-board IR receiver, enable it.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
A64-OLinuXino uses DCDC1 (VCC-IO) for MMC1 supply. In commit 916b68cfe4
("arm64: dts: a64-olinuxino: Enable RTL8723BS WiFi") ALDO2 is set, which is
VCC-PL. Since DCDC1 is always present, the boards are working without a
problem.
This patch sets the correct regulator.
Fixes: 916b68cfe4 ("arm64: dts: a64-olinuxino: Enable RTL8723BS WiFi")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
A64-OLinuXino-eMMC uses 1.8V for eMMC supply. This is done via a triple
jumper, which sets VCC-PL to either 1.8V or 3.3V. This setting is different
for boards with and without eMMC.
This is not a big issue for DDR52 mode, however the eMMC will not work in
HS200/HS400, since these modes explicitly requires 1.8V.
Fixes: 94f68f3a4b ("arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)")
Cc: stable@vger.kernel.org # v5.4
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+QmuaPwR3wnBdVwACF8+vY7k4RUFAl3dKsYACgkQCF8+vY7k
4RWmzBAAnIL1V0Jb6vJo9AJUmntDiO/3lVGjz+6bzvlhsjbPD0/6r1AY2ZRZxO97
U3TTnB9m1nRjtJaaZ5Lmx9kc9suB8u1s9HziTcKIQ971goSZapmrx3IKPK64jt5D
Uw6nzfinvAgRw0Rt0t6yd+yciw5bsqmGR5iIz/A29BXHnVu5P2TcGE8IM/oloxqV
ZQkff30jieSM3CXq9hQSoekJkipyCXN3xbKncVVHc4TEonvXSCcAQxC6tRulKpi/
Y/MOxB3v7Vh3snVe5lI3fBYPr8Iw8xpBTMXg7s5e4Sb9aCeZioF0cb2nLJFG8tw8
2TviW1Fktt/N1nwZreRgVMkl19fGm3IdVd+1ukWgXS4EvV3FFsx3FZMFgAebhvKZ
1SHxhGyC5yc5yDl8f9/yo/cyKRzeDj7h6SSD2TUKRmnKXWBin9cNr3CPNJDvTk6Q
rgb2B/Sbs00fZFihRdkt8n6SmHpARS4QBZiAKpHECZhmBKNqFLg050v0uzB1Z7D8
r7gK8NIWQORnmLWmHCa/kCAB8syUm8cW6LibWAvCbfN0FEaYdujFtvC+v0BQSTVJ
f9BNFwUs3mCJ6x30F2DN60f2z3G1ehuNPMxFBFJpa9sLgh2wEPVaqEakGWE2iMUP
Rv/cz0CJQweJutdhIAHtk3nVOQZeiAcqZMeHYemX9lL62Mjprmo=
=VN90
-----END PGP SIGNATURE-----
Merge tag 'media/v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- uAPI documentation for stateless decoders
- Added a new CEC ioctl together with its documentation
- Improved IPU3 documentation
- New i2c drivers: hi556 and imx290
- Added support on Vivid driver for meta streams
- Added de-interlace support for sunxi subdriver
- Added a few new remote controler keymaps
- Added H.265 support for Sunxi Cedrus driver
- Another round of random driver cleanups, fixes and improvements
* tag 'media/v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (361 commits)
media: Revert "media: mtk-vcodec: Remove extra area allocation in an input buffer on encoding"
media: hantro: Set H264 FIELDPIC_FLAG_E flag correctly
media: hantro: Remove now unused H264 pic_size
media: hantro: Use output buffer width and height for H264 decoding
media: hantro: Reduce H264 extra space for motion vectors
media: hantro: Fix H264 motion vector buffer offset
media: ti-vpe: vpe: fix compatible to match bindings
media: dt-bindings: media: ti-vpe: Document VPE driver
media: zr364xx: remove redundant assigmnent to idx, clean up code
media: Documentation: media: *_DEFAULT targets for subdevs
media: hantro: Fix s_fmt for dynamic resolution changes
media: i2c: Use the correct style for SPDX License Identifier
media: siano: Use the correct style for SPDX License Identifier
media: vicodec: media_device_cleanup was called too early
media: vim2m: media_device_cleanup was called too early
media: cedrus: Increase maximum supported size
media: cedrus: Fix H264 4k support
media: cedrus: Properly signal size in mode register
media: v4l2-ctrl: Lock main_hdl on operations of requests_queued.
media: si470x-i2c: add missed operations in remove
...
Beelink GS1 ships with a NEC remote control.
Add the rc keymap to the device-tree.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
- USB3 support for the H6
- Deinterlacer support for the H3
- eDP Bridge support on the Teres-I
- More DT cleanups thanks to the validation
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXcK5xwAKCRDj7w1vZxhR
xZagAP9dDphr5+3Ah5E01ANIbI3xiEITkMm55DjahFUtcoygogEA82VvUmCNMzRx
UVt2+k/eLB12V0RPsCCeCKXGCt34OgI=
=arSK
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-5.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
A few more DT patches for 5.5, mostly:
- USB3 support for the H6
- Deinterlacer support for the H3
- eDP Bridge support on the Teres-I
- More DT cleanups thanks to the validation
* tag 'sunxi-dt-for-5.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h6: Remove useless reset name
ARM: dts: sun6i: Remove useless reset-names
arm64: dts: allwinner: orange-pi-3: Enable USB 3.0 host support
arm64: dts: allwinner: h6: add USB3 device nodes
dt-bindings: Add ANX6345 DP/eDP transmitter binding
arm64: dts: allwinner: a64: enable ANX6345 bridge on Teres-I
dts: arm: sun8i: h3: Enable deinterlace unit
ARM: dts: sunxi: h3/h5: Add MBUS controller node
dt-bindings: bus: sunxi: Add H3 MBUS compatible
Link: https://lore.kernel.org/r/58ad00a8-9579-4811-969a-a74e331ee9a2.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
interrupts were improper in a previous fixes PR.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXcK4vQAKCRDj7w1vZxhR
xYicAP47+z/2soJsnUf1jahKsVFqYoxKa+Z+qYg/f/hdphEvCwD+JqY46XbjbaL7
hzHqYYQvJ1OAO/Mks3ms01/0ZnhbKww=
=9zaU
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-5.4-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
One patch to add back the PMU node that was removed because the
interrupts were improper in a previous fixes PR.
* tag 'sunxi-fixes-for-5.4-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: Re-add PMU node
ARM: sunxi: Fix CPU powerdown on A83T
ARM: dts: sun8i-a83t-tbs-a711: Fix WiFi resume from suspend
ARM: dts: sun7i: Drop the module clock from the device tree
dt-bindings: media: sun4i-csi: Drop the module clock
media: dt-bindings: Fix building error for dt_binding_check
arm64: dts: allwinner: a64: sopine-baseboard: Add PHY regulator delay
arm64: dts: allwinner: a64: Drop PMU node
arm64: dts: allwinner: a64: pine64-plus: Add PHY regulator delay
Link: https://lore.kernel.org/r/45023fa6-b2bc-4934-b85c-3e7841dde0b1.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
As it was found recently, the Performance Monitoring Unit (PMU) on the
Allwinner A64 SoC was not generating (the right) interrupts. With the
SPI numbers from the manual the kernel did not receive any overflow
interrupts, so perf was not happy at all.
It turns out that the numbers were just off by 4, so the PMU interrupts
are from 148 to 151, not from 152 to 155 as the manual describes.
This was found by playing around with U-Boot, which typically does not
use interrupts, so the GIC is fully available for experimentation:
With *every* PPI and SPI enabled, an overflowing PMU cycle counter was
found to set a bit in one of the GICD_ISPENDR registers, with careful
counting this was determined to be number 148.
Tested with perf record and perf top on a Pine64-LTS. Also tested with
tasksetting to every core to confirm the assignment between IRQs and
cores.
This somewhat "revert-fixes" commit ed3e9406bc ("arm64: dts: allwinner:
a64: Drop PMU node").
Fixes: 34a97fcc71 ("arm64: dts: allwinner: a64: Add PMU node")
Fixes: ed3e9406bc ("arm64: dts: allwinner: a64: Drop PMU node")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Enable Allwinner's USB 3.0 phy and the host controller. Orange Pi 3
board has GL3510 USB 3.0 4-port hub connected to the SoC's USB 3.0
port. All four ports are exposed via USB3-A connectors. VBUS is
always on, since it's powered directly from DCIN (VCC-5V) and
not switchable.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Allwinner H6 SoC features USB3 functionality, with a DWC3 controller and
a custom PHY.
Add device tree nodes for them.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Teres-I has an anx6345 bridge connected to the RGB666 LCD output, and
the I2C controlling signals are connected to I2C0 bus.
Enable it in the device tree, and enable the display engine, video mixer
and tcon0 as well.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Unlike other H6 boards, Tanix TX6 doesn't have a PMIC so we can enable
the GPU without providing a specific power supply.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The Emlid Neutis N5 board has AP6212 BT+WiFi chip. This patch is in
line with 8558c6e21c ("ARM: dts: sun8i: h3: bluetooth for Banana Pi
M2 Zero board") and other commits that add Bluetooth support for
similar boards.
Signed-off-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The Crypto Engine is a hardware cryptographic accelerator that supports
many algorithms.
This patch enables the Crypto Engine on the Allwinner H6 SoC Device-tree.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The Crypto Engine is a hardware cryptographic accelerator that supports
many algorithms.
It could be found on most Allwinner SoCs.
This patch enables the Crypto Engine on the Allwinner H5 SoC Device-tree.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The Crypto Engine is a hardware cryptographic accelerator that supports
many algorithms.
It could be found on most Allwinner SoCs.
This patch enables the Crypto Engine on the Allwinner A64 SoC Device-tree.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Enable and add supply to the Mali GPU node on all the
H6 boards.
Regarding the datasheet the maximum time for supply to reach
its voltage is 32ms.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
A slightly larger set of fixes have accrued in the last two weeks.
Mostly a collection of the usual smaller fixes:
- Marvell Armada: USB phy setup issues on Turris Mox
- Broadcom: GPIO/pinmux DT mapping corrections for Stingray, MMC bus
width fix for RPi Zero W, GPIO LED removal for RPI CM3. Also some
maintainer updates.
- OMAP: Fixlets for display config, interrupt settings for wifi, some
clock/PM pieces. Also IOMMU regression fix and a ti-sysc no-watchdog
regression fix.
- i.MX: A few fixes around PM/settings, some devicetree fixlets and
catching up with config option changes in DRM
- Rockchip: RockRro64 misc DT fixups, Hugsun X99 USB-C, Kevin display
panel settings
... and some smaller fixes for Davinci (backlight, McBSP DMA), Allwinner
(phy regulators, PMU removal on A64, etc).
-----BEGIN PGP SIGNATURE-----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=Jy/6
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A slightly larger set of fixes have accrued in the last two weeks.
Mostly a collection of the usual smaller fixes:
- Marvell Armada: USB phy setup issues on Turris Mox
- Broadcom: GPIO/pinmux DT mapping corrections for Stingray, MMC bus
width fix for RPi Zero W, GPIO LED removal for RPI CM3. Also some
maintainer updates.
- OMAP: Fixlets for display config, interrupt settings for wifi, some
clock/PM pieces. Also IOMMU regression fix and a ti-sysc
no-watchdog regression fix.
- i.MX: A few fixes around PM/settings, some devicetree fixlets and
catching up with config option changes in DRM
- Rockchip: RockRro64 misc DT fixups, Hugsun X99 USB-C, Kevin display
panel settings
... and some smaller fixes for Davinci (backlight, McBSP DMA),
Allwinner (phy regulators, PMU removal on A64, etc)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
MAINTAINERS: Update the Spreadtrum SoC maintainer
MAINTAINERS: Remove Gregory and Brian for ARCH_BRCMSTB
ARM: dts: bcm2837-rpi-cm3: Avoid leds-gpio probing issue
bus: ti-sysc: Fix watchdog quirk handling
ARM: OMAP2+: Add pdata for OMAP3 ISP IOMMU
ARM: OMAP2+: Plug in device_enable/idle ops for IOMMUs
ARM: davinci_all_defconfig: enable GPIO backlight
ARM: davinci: dm365: Fix McBSP dma_slave_map entry
ARM: dts: bcm2835-rpi-zero-w: Fix bus-width of sdhci
ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM
arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk
ARM: dts: imx7s: Correct GPT's ipg clock source
ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect'
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
arm64: dts: lx2160a: Correct CPU core idle state name
mailmap: Add Simon Arlott (replacement for expired email address)
arm64: dts: rockchip: Fix override mode for rk3399-kevin panel
...
Follow what the sun50i-a64-pine64.dts does and expose all 5 serial
connections.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
The board contains AP6256 WiFi/BT module that has its bluetooth part
connected to SoC's UART1 port. Enable this port, and add node for the
bluetooth device.
Bluetooth part is named bcm4345c5.
You'll need a BCM4345C5.hcd firmware file that can be found in the
Xulongs's repository for H6:
https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256
The driver expects the firmware at the following path relative to the
firmware directory:
brcm/BCM4345C5.hcd
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Orange Pi 3 uses UART1 for bluetooth. Add pinconfigs so that we can use
them.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
This patch enables internal audio codec on OrangePi Win board by
enabling all relevant nodes and adding appropriate routing. Board has
on-board microphone (MIC1) and 3.5 mm jack with stereo audio and
microphone (MIC2).
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
This reverts commits 3d109bdca9 ("ARM: dts: sunxi: Remove useless
phy-names from EHCI and OHCI"), 0a3df8bb6d ("ARM: dts: sunxi: h3/h5:
Remove useless phy-names from EHCI and OHCI") and 3c7ab90aaa ("arm64:
dts: allwinner: Remove useless phy-names from EHCI and OHCI").
It turns out that while the USB bindings were not mentionning it, the PHY
client bindings were mandating that phy-names is set when phys is. Let's
add it back.
Fixes: 3d109bdca9 ("ARM: dts: sunxi: Remove useless phy-names from EHCI and OHCI")
Fixes: 0a3df8bb6d ("ARM: dts: sunxi: h3/h5: Remove useless phy-names from EHCI and OHCI")
Fixes: 3c7ab90aaa ("arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191002112651.100504-1-mripard@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out that sopine-baseboard needs same fix as pine64-plus
for ethernet PHY. Here too Realtek ethernet PHY chip needs additional
power on delay to properly initialize. Datasheet mentions that chip
needs 30 ms to be properly powered on and that it needs some more time
to be initialized.
Fix that by adding 100ms ramp delay to regulator responsible for
powering PHY.
Note that issue was found out and fix tested on pine64-lts, but it's
basically the same as sopine-baseboard, only layout and connectors
differ.
Fixes: bdfe4cebea ("arm64: allwinner: a64: add Ethernet PHY regulator for several boards")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Looks like PMU in A64 is broken, it generates no interrupts at all and
as result 'perf top' shows no events.
Tested on Pine64-LTS.
Fixes: 34a97fcc71 ("arm64: dts: allwinner: a64: Add PMU node")
Cc: Harald Geyer <harald@ccbib.org>
Cc: Jared D. McNeill <jmcneill@NetBSD.org>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Emmanuel Vadot <manu@FreeBSD.org>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Depending on kernel and bootloader configuration, it's possible that
Realtek ethernet PHY isn't powered on properly. According to the
datasheet, it needs 30ms to power up and then some more time before it
can be used.
Fix that by adding 100ms ramp delay to regulator responsible for
powering PHY.
Fixes: 94dcfdc77f ("arm64: allwinner: pine64-plus: Enable dwmac-sun8i")
Suggested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Orange Pi 3 has AP6256 WiFi/BT module. WiFi part of the module is called
bcm43356 and can be used with the brcmfmac driver. The module is powered by
the two always on regulators (not AXP805).
WiFi uses a PG port with 1.8V voltage level signals. SoC needs to be
configured so that it sets up an 1.8V input bias on this port. This is done
by the pio driver by reading the vcc-pg-supply voltage.
You'll need a fw_bcm43456c5_ag.bin firmware file and nvram.txt
configuration that can be found in the Xulongs's repository for H6:
https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256
Mainline brcmfmac driver expects the firmware and nvram at the following
paths relative to the firmware directory:
brcm/brcmfmac43456-sdio.bin
brcm/brcmfmac43456-sdio.txt
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The watchdog has a clock on all our SoCs, but it wasn't always listed.
Add it to the devicetree where it's missing.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This patch adds RTC node and fixes the clock properties and nodes
to reflect the real clock tree.
The device nodes for the internal oscillator and osc32k are removed,
as these clocks are now provided by the RTC device. Clock references
are fixed accordingly, too.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.
This patch has been tested on A64-OLinuXino-1Ge16GW with Linux 5.0 from Debain.
Basic benchmarks using Flexible IO Tester show reasonable performance from the
eMMC.
eMMC - Random Write: 21.3MiB/s
eMMC - Sequential Write: 68.2MiB/s
SD Card - Random Write: 1690KiB/s
SD Card - Sequential Write: 11.0MiB/s
Changes:
v3: Separate dts for eMMC variants
v2: Fix descriptions for VCC and VCCQ
Link: 174953de1e
Signed-off-by: Martin Ayotte <martinayotte@gmail.com>
[sunil@medhas.org Fix descriptions for VCC and VCCQ, separate dts for eMMC]
Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org>
Tested-by: Sunil Mohan Adapa <sunil@medhas.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tanix TX6 is an Allwinner H6 based TV box, which supports:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 4GiB DDR3 RAM (3GiB useable)
- 100Mbps EMAC via AC200 EPHY
- Cdtech 47822BS Wifi/BT
- 2x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- IR receiver
- 64GiB eMMC
- 5V/2A DC power supply
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add device-tree nodes for i2c0 to i2c2, and also add relevant pinctrl
nodes.
Suggested-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Beelink GS1 has a DDC I2C bus voltage shifter. This is actually missing
and video is limited to 1024x768 due to missing EDID information.
Add the DDC regulator in the device-tree.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Beelink GS1 board has a SPDIF out connector, so enable it in
the device-tree and add a simple SPDIF soundcard.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner H6 has a SPDIF controller called OWA (One Wire Audio).
Only one pinmuxing is available so set it as default.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Orange Pi 3 has a DDC_CEC_EN signal connected to PH2, that enables the DDC
I2C bus voltage shifter. Before EDID can be read, we need to pull PH2 high.
This is realized by the ddc-en-gpios property.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Beelink GS1, OrangePi H6 boards and Pine H64 have an IR receiver.
Enable it in their device-tree.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 IR is similar to A31 and can use same driver.
Add support for it.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
OrangePi Win board contains IR receiver. Enable it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
IR peripheral is completely compatible with A31 one.
Signed-off-by: Igors Makejevs <git_bb@bwzone.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Even though the binding mentions that the PHY name must be "phy", it turns
out that all our DTs had "hdmi-phy" instead.
The code doesn't care about the phy-names property, so we can just change
our DTs to match the binding, without any side effect.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The SID node one the H6 doesn't have a standard node name. Switch to the
one we use for the other SoCs.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The DE2 bus takes two clocks, named bus and mod according to the binding.
However, the order of these clocks change from one SoC to another. Even
though it might not be an issue in most cases, having consistency will help
if we ever need to have some code to deal with deprecated bindings, and in
general it's just better.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
One extra change wiring up the interrupt line for the external RTC chip
on the Pine H64.
-----BEGIN PGP SIGNATURE-----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=cinn
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-5.3-round-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner DT64 Changes for 5.3 - Round 2
One extra change wiring up the interrupt line for the external RTC chip
on the Pine H64.
* tag 'sunxi-dt64-for-5.3-round-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h6: Pine H64: Add interrupt line for RTC
Link: https://lore.kernel.org/r/20190704065326.GA19010@wens.csie.org
Signed-off-by: Olof Johansson <olof@lixom.net>
arm and arm64, a fix for the array syntax raised by our DT schemas.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXQyRegAKCRDj7w1vZxhR
xQ7SAP9gWeCGiyq+N2lvgFUOMVUezlDcJx2IVjoJvSQcyjeD2QD/W0m+fldHe7BB
PEv3s5BbYAYFHe+krqTPejcLK+c5hwg=
=4UQl
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-5.3-201906210812' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
This time we only have a single patch for our command branch between
arm and arm64, a fix for the array syntax raised by our DT schemas.
* tag 'sunxi-h3-h5-for-5.3-201906210812' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sunxi: h3/h5: Fix GPIO regulator state array
Signed-off-by: Olof Johansson <olof@lixom.net>
The external PCF8563 RTC chip's interrupt line is connected to the NMI
line on the SoC.
Add the interrupt line to the device tree.
Fixes: 17ebc33afc ("arm64: allwinner: h6: add PCF8563 RTC on Pine H64 board")
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
H6 has DMA controller which supports 16 channels.
Add a node for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Even though it translates to the same thing down to the binary level, we
should have an array of 2 number cells to describe each voltage state,
which in turns create a validation warning.
Let's fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 has a r_watchdog similar to A64.
Declare it in the device-tree.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 has a watchog node which seems broken
on some boards.
Test has been performed on several boards.
Chen-Yu Tsai boards:
Pine H64 - H6448BA 7782 => OK
OrangePi Lite 2 - H8068BA 61C2 => KO
Martin Ayotte boards:
Pine H64 - H8069BA 6892 => OK
OrangePi 3 - HA047BA 69W2 => KO
OrangePi One Plus - H7310BA 6842 => KO
OrangePi Lite2 - H6448BA 6662 => KO
Clément Péron board:
Beelink GS1 - H7309BA 6842 => KO
As it seems not fixable for now, declare the node
but leave it disable with a comment.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The TERES-I has internal speakers (left, right), internal microphone
and a headset combo jack (headphones + mic), "CTIA" (android) pinout.
The headphone and mic detect lines of the A64 are connected properly,
but AFAIK currently unsupported by the driver.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Bananapi M64 has a micro-USB connector with USB OTG support (that
is already enabled). VBUS from this connector is wired to the PMIC's
VBUS input.
Enable the PMIC's USB power supply on this board, and also hook it up
to the USB PHY.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AXP803 has a VBUS power input. Add a device node for it,
now that we support it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side
identifies as BCM43430, while the Bluetooth side identifies as BCM43438.
WiFi is connected to mmc1 and the Bluetooth side is connected to UART1
in a 4 wire configuration. Same as the WiFi side, due to being the same
chip and package, DLDO2 provides overall power via VBAT, and DLDO4
provides I/O power via VDDIO. The RTC clock output provides the LPO low
power clock at 32.768 kHz.
This patch enables WiFi and Bluetooth on OrangePi Win boards and adds
missing LPO clock on the WiFi side. PCM connection also exists for
Bluetooth audio, but it's not used here.
Bluetooth UART speed is set to 1.5 MBaud in order to be able transmit
audio. While module supports even higher speeds, currently sunxi clock
driver doesn't support higher speed.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner H6 SoC features tweakable VCC for PC, PD, PG, PL and PM
banks.
This patch adds supplies for these banks except PL bank. PL bank is
where PMIC is attached, and currently if a PMIC regulator is added
for it a dependency loop will happen.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Goodix GT911 CTP is bound with Oceanic 5205 5inMFD board.
The CTP connected to board with,
- SDA, SCK from i2c0
- GPIO-LD0 as AVDD28 supply
- PH4 gpio as interrupt pin
- PH11 gpio as reset pin
- X axis is inverted
- Y axis is inverted
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add Goodix GT5663 capacitive touch controller node on
Amarula A64-Relic board.
The CTP connected to board with,
- SDA, SCK from i2c1
- GPIO-LD0 as AVDD28 supply
- PH4 gpio as interrupt pin
- PH8 gpio as reset pin
- X axis is inverted
- Y axis is inverted
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
There is only one pinmuxing available for each I2C controller.
So, move pinctrl for i2c0, i2c1 from board dts files into SoC dtsi.
By moving these pinctrls the i2c1 node from Nanopi A64 just have a
status, which is disabled already so remove the entire node from it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Our usual bunch of changes shared between arm and arm64, the most notable
one being:
- Fix of improper usage of DT bindings, thanks to the DT validation
- Add the SID for the H3 and H5
- New board: RerVision H3-DVK
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXLm2aQAKCRDj7w1vZxhR
xQJYAQDs7mcoEHwBqw+1iZGmHZuvj4jJXdAd/FkmoujMawaGoQD/a4zddy8AL7s9
WA9I42cSuBwfZjftLX/br4Ycssd1sgQ=
=90I8
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner H3/H5 changes for 5.2
Our usual bunch of changes shared between arm and arm64, the most notable
one being:
- Fix of improper usage of DT bindings, thanks to the DT validation
- Add the SID for the H3 and H5
- New board: RerVision H3-DVK
* tag 'sunxi-h3-h5-for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: mapleboard: Remove cd-inverted
ARM: dts: sunxi: h3/h5: Remove useless phy-names from EHCI and OHCI
ARM: dts: sun8i: h3: bluetooth for Banana Pi M2 Zero board
ARM: dts: sun8i: h3: Add default dr_mode
ARM: dts: sun8i: h3: Refactor the pinctrl node names
ARM: dts: sunxi: h3/h5: Remove stale pinctrl-names entry
ARM: dts: sunxi: h3/h5: Add device node for SID
ARM: dts: sun8i-h3: Add support for the RerVision H3-DVK board
Signed-off-by: Olof Johansson <olof@lixom.net>
Amarula A64-Relic board by default bound with OV5640 camera,
so add support for it with below pin information.
- PE13, PE12 via i2c-gpio bitbanging
- CLK_CSI_MCLK as external clock
- PE1 as external clock pin muxing
- ALDO1 as AVDD supply
- DLDO3 as DOVDD supply
- ELDO3 as DVDD supply
- PE14 gpio for reset pin
- PE15 gpio for powerdown pin
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Some camera modules have the SoC feeding a master clock to the sensor
instead of having a standalone crystal. This clock signal is generated
from the clock control unit and output from the CSI MCLK function of
pin PE1.
Add a pinmux setting for it for camera sensors to reference.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
According to the device tree specification, any bus should have a 'bus'
node name.
Since it isn't the case for us on the DE2 bus, fix that.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Neither the OHCI or EHCI bindings are using the phy-names property, so we
can just drop it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
MMC1 is used on some H6 boards we want to support. Typical use is 4-bit
SDIO interface with a WiFi chip. Add pin definitions for this use case.
As this is the only possible configration for mmc1, make it the default
one, too.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Orange Pi 3 is a H6 based SBC made by Xulong, released in January 2019. It
has the following features:
- Allwinner H6 quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB or 2GB LPDDR3 RAM
- AXP805 PMIC
- AP6256 Wifi/BT 5.0
- USB 2.0 host port (A)
- USB 2.0 micro usb, OTG
- USB 3.0 Host + 4 port USB hub (GL3510)
- Gigabit Ethernet (Realtek RTL8211E phy)
- HDMI 2.0 port
- soldered eMMC (optional)
- 3x LED (one is on the bottom)
- microphone
- audio jack
- PCIe
Add basic support for the board.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- FN-Link 6222B-SRB Wifi/BT
- 1x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- S/PDIF Tx
- IR receiver
- 5V/2A DC power supply
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
There is only one pinmuxing available for each MMC controller.
Move the pinctrl to the SOC
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The device tree binding already lists compatible strings for H6
SoC, so add a device node for it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The I2S binding never mentions a reset-names property, or mentions which
value it should have. To avoid any further issue, remove it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The USB OTG binding we have mandates to have a dr_mode property, yet not
all boards are setting it.
Since the generic otg binding states that the default mode should be the
OTG mode, let's use that one in our DTSI.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The H3 and H5 have never been converted to the new convention we want to
have for the pinctrl nodes.
Convert them.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Some nodes still have pinctrl-names entry, yet they don't have any pinctrl
group anymore. Drop them.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Some pinctrl node names for the A64 and H6 do not follow the convention
that we switched to and enforced, most notably by using underscores in node
names, which also trigger a DTC warning.
Let's change that.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The pinctrl binding mandates that we have the three clocks fed into the PIO
described.
Even though the old case is still supported for backward compatibility, we
should update our DTs to fix this.
Fixes: 6bc37fac30 ("arm64: dts: add Allwinner A64 SoC .dtsi")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Commit a7f7047ffc ("arm64: dts: allwinner: a64: Add cross links for the
mixers") introduced a few errors while fixing the cross links. Make sure to
correct them.
Fixes: a7f7047ffc ("arm64: dts: allwinner: a64: Add cross links for the mixers")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Even though we shouldn't really have any external user of the clock
provided by the TCON, if clock-output-names is set, then #clock-cells must
be there as well.
Fix this.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A64 datasheet lists the supply rail for the headphone amp's charge
pump as "CPVDD". cpvdd-supply is the name of the property for this power
rail specified in the device tree bindings. "HPVCC" was the name used in
the A33 datasheet for the same function.
Rename the supply so it matches the datasheet and bindings.
Fixes: c56689e6f2 ("arm64: dts: allwinner: a64: bananapi-m64: Enable audio codec")
Fixes: 6de8e71784 ("arm64: dts: allwinner: a64: enable sound on Pinebook")
Fixes: 498c21f233 ("arm64: dts: allwinner: a64: enable sound on Pine64 and SoPine")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The device tree binding already lists compatible strings for these two
SoCs. Add a device node for them.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This adds the Video engine node for H6. It can use whole DRAM range so
there is no need for reserved memory node.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Unlike what the binding for multiple pipeline documents, the A64 doesn't
have the cross links between the TCON and the mixers.
Let's add them.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Oceanic 5205 5inMFD is a 5 inch Multi function display baseboard
designed to mount SoPine SOM.
Key features:
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 2GB DDR3 RAM
- SD Slot
- SPI-NOR flash
- EMAC, RTL8211E
- MCP2515 CAN
- 4-lane, MIPI-DSI panel
- Goodix 911 CTP
- USB Host
- 12V DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Amarula A64 Relic has STLM75 sensor for digital temperature
and thermal watchdog.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Enable pwm and add a pretty standard backlight node.
The regulator is always on, but we include it anyway, because it is
required by the binding document.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This is a smaller update than the past few times, but with just over
500 non-merge changesets still dwarfes the rest of the SoC tree.
Three new SoC platforms get added, each one a follow-up to an existing
product, and added here in combination with a reference platform:
- Renesas RZ/A2M (R7S9210) 32-bit Cortex-A9 Real-time imaging processor
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rza/rza2m.html
- Renesas RZ/G2E (r8a774c0) 64-bit Cortex-A53 SoC "for
Rich Graphics Applications".
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg2e.html
- NXP i.MX8QuadXPlus 64-bit Cortex-A35 SoC
https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/i.mx-applications-processors/i.mx-8-processors/i.mx-8x-family-arm-cortex-a35-3d-graphics-4k-video-dsp-error-correcting-code-on-ddr:i.MX8X
These are actual commercial products we now support with an in-kernel
device tree source file:
- Bosch Guardian is a product made by Bosch Power
Tools GmbH, based on the Texas Instruments AM335x chip
- Winterland IceBoard is a Texas Instruments AM3874 based
machine used in telescopes at the south pole and elsewhere, see commit
d031773169 for some pointers:
- Inspur on5263m5 is an x86 server platform with an Aspeed
ast2500 baseboard management controller. This is for running on
the BMC.
- Zodiac Digital Tapping Unit, apparently a kind of ethernet
switch used in airplanes.
- Phicomm K3 is a WiFi router based on Broadcom bcm47094
- Methode Electronics uDPU FTTdp distribution point unit
- X96 Max, a generic TV box based on Amlogic G12a (S905X2)
- NVIDIA Shield TV (Darcy) based on Tegra210
And then there are several new SBC, evaluation, development or modular
systems that we add:
- Three new Rockchips rk3399 based boards:
- FriendlyElec NanoPC-T4 and NanoPi M4
- Radxa ROCK Pi 4
- Five new i.MX6 family SoM modules and boards for industrial
products:
- Logic PD i.MX6QD SoM and evaluation baseboad
- Y Soft IOTA Draco/Hydra/Ursa family boards based on i.MX6DL
- Phytec phyCORE i.MX6 UltraLite SoM and evaluation module
- MYIR Tech MYD-LPC4357 development based on the NXP lpc4357
microcontroller
- Chameleon96, an Intel/Altera Cyclone5 based FPGA development
system in 96boards form factor
- Arm Fixed Virtual Platforms(FVP) Base RevC, a purely
virtual platform for corresponding to the latest "fast model"
- Another Raspberry Pi variant: Model 3 A+, supported both
in 32-bit and 64-bit mode.
- Oxalis Evalkit V100 based on NXP Layerscape LS1012a,
in 96Boards enterprise form factor
- Elgin RV1108 R1 development board based on 32-bit Rockchips RV1108
For already supported boards and SoCs, we often add support for new
devices after merging the drivers. This time, the largest changes include
updates for
- STMicroelectronics stm32mp1, which was now formally
launched last week
- Qualcomm Snapdragon 845, a high-end phone and low-end laptop chip
- Action Semi S700
- TI AM654x, their recently merged 64-bit SoC from the OMAP family
- Various Amlogic Meson SoCs
- Mediatek MT2712
- NVIDIA Tegra186 and Tegra210
- The ancient NXP lpc32xx family
- Samsung s5pv210, used in some older mobile phones
Many other chips see smaller updates and bugfixes beyond that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=1goV
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"This is a smaller update than the past few times, but with just over
500 non-merge changesets still dwarfes the rest of the SoC tree.
Three new SoC platforms get added, each one a follow-up to an existing
product, and added here in combination with a reference platform:
- Renesas RZ/A2M (R7S9210) 32-bit Cortex-A9 Real-time imaging
processor:
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rza/rza2m.html
- Renesas RZ/G2E (r8a774c0) 64-bit Cortex-A53 SoC "for Rich Graphics
Applications":
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg2e.html
- NXP i.MX8QuadXPlus 64-bit Cortex-A35 SoC:
https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/i.mx-applications-processors/i.mx-8-processors/i.mx-8x-family-arm-cortex-a35-3d-graphics-4k-video-dsp-error-correcting-code-on-ddr:i.MX8X
These are actual commercial products we now support with an in-kernel
device tree source file:
- Bosch Guardian is a product made by Bosch Power Tools GmbH, based
on the Texas Instruments AM335x chip
- Winterland IceBoard is a Texas Instruments AM3874 based machine
used in telescopes at the south pole and elsewhere, see commit
d031773169 for some pointers:
- Inspur on5263m5 is an x86 server platform with an Aspeed ast2500
baseboard management controller. This is for running on the BMC.
- Zodiac Digital Tapping Unit, apparently a kind of ethernet switch
used in airplanes.
- Phicomm K3 is a WiFi router based on Broadcom bcm47094
- Methode Electronics uDPU FTTdp distribution point unit
- X96 Max, a generic TV box based on Amlogic G12a (S905X2)
- NVIDIA Shield TV (Darcy) based on Tegra210
And then there are several new SBC, evaluation, development or modular
systems that we add:
- Three new Rockchips rk3399 based boards:
- FriendlyElec NanoPC-T4 and NanoPi M4
- Radxa ROCK Pi 4
- Five new i.MX6 family SoM modules and boards for industrial
products:
- Logic PD i.MX6QD SoM and evaluation baseboad
- Y Soft IOTA Draco/Hydra/Ursa family boards based on i.MX6DL
- Phytec phyCORE i.MX6 UltraLite SoM and evaluation module
- MYIR Tech MYD-LPC4357 development based on the NXP lpc4357
microcontroller
- Chameleon96, an Intel/Altera Cyclone5 based FPGA development system
in 96boards form factor
- Arm Fixed Virtual Platforms(FVP) Base RevC, a purely virtual
platform for corresponding to the latest "fast model"
- Another Raspberry Pi variant: Model 3 A+, supported both in 32-bit
and 64-bit mode.
- Oxalis Evalkit V100 based on NXP Layerscape LS1012a, in 96Boards
enterprise form factor
- Elgin RV1108 R1 development board based on 32-bit Rockchips RV1108
For already supported boards and SoCs, we often add support for new
devices after merging the drivers. This time, the largest changes
include updates for
- STMicroelectronics stm32mp1, which was now formally launched last
week
- Qualcomm Snapdragon 845, a high-end phone and low-end laptop chip
- Action Semi S700
- TI AM654x, their recently merged 64-bit SoC from the OMAP family
- Various Amlogic Meson SoCs
- Mediatek MT2712
- NVIDIA Tegra186 and Tegra210
- The ancient NXP lpc32xx family
- Samsung s5pv210, used in some older mobile phones
Many other chips see smaller updates and bugfixes beyond that"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (506 commits)
ARM: dts: exynos: Fix max voltage for buck8 regulator on Odroid XU3/XU4
dt-bindings: net: ti: deprecate cpsw-phy-sel bindings
ARM: dts: am335x: switch to use phy-gmii-sel
ARM: dts: am4372: switch to use phy-gmii-sel
ARM: dts: dm814x: switch to use phy-gmii-sel
ARM: dts: dra7: switch to use phy-gmii-sel
arch: arm: dts: kirkwood-rd88f6281: Remove disabled marvell,dsa reference
ARM: dts: exynos: Add support for secondary DAI to Odroid XU4
ARM: dts: exynos: Add support for secondary DAI to Odroid XU3
ARM: dts: exynos: Disable ARM PMU on Odroid XU3-lite
ARM: dts: exynos: Add stdout path property to Arndale board
ARM: dts: exynos: Add minimal clkout parameters to Exynos3250 PMU
ARM: dts: exynos: Enable ADC on Odroid HC1
arm64: dts: sprd: Remove wildcard compatible string
arm64: dts: sprd: Add SC27XX fuel gauge device
arm64: dts: sprd: Add SC2731 charger device
arm64: dts: sprd: Add ADC calibration support
arm64: dts: sprd: Remove PMIC INTC irq trigger type
arm64: dts: rockchip: Enable tsadc device on rock960
ARM: dts: rockchip: add chosen node on veyron devices
...
Our usual round of DT changes for the arm64 Allwinner SoCs:
- Enabling of the various power supplies on most a64 boards
- H6 SRAM controller support
- A64 CSI support
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXF1ZiQAKCRDj7w1vZxhR
xeeaAQCuII0MyMyRYhk4XPkjRncEks7A1Fp7u1kjR4VjbNq8JQD+OhCbKMAz4DVv
T7DeI92HwEO2Dx/ggNMVYDCUDyH55gI=
=Pd5b
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner arm64 DT changes for 5.1, take 2
Our usual round of DT changes for the arm64 Allwinner SoCs:
- Enabling of the various power supplies on most a64 boards
- H6 SRAM controller support
- A64 CSI support
* tag 'sunxi-dt64-for-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: Enable PMIC power supplies on various boards
arm64: dts: allwinner: a64: teres-i: enable power supplies
arm64: dts: allwinner: h6: Add support for the SRAM C1 section
dt-bindings: sram: sunxi: Add compatible for the H6 SRAM C1
arm64: dts: allwinner: a64: Add A64 CSI controller
arm64: dts: allwinner: h6: Move GIC device node fix base address ordering
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Our usual round of DT changes shared between arm and arm64.
We have a bunch of changes for board, improving the eMMC support on the H5
variant of the All-H3-CC, enabling HDMI and reworking the CSI driver.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXF1X8QAKCRDj7w1vZxhR
xX9ZAP9KwFKKehrS1QJjTHKeowUKEnRHuDj2MlwTZJgCw/AMMgEAzgRZwY/VH/Os
aQIhJho9hWmBE0dePIZuWzzCp1giNw8=
=7jQV
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner H3 and H5 changes for 5.1
Our usual round of DT changes shared between arm and arm64.
We have a bunch of changes for board, improving the eMMC support on the H5
variant of the All-H3-CC, enabling HDMI and reworking the CSI driver.
* tag 'sunxi-h3-h5-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h5: libretech-all-h3-cc: Mark eMMC HS-DDR 3.3V capable
ARM: dts: sunxi: h3/h5: Drop A31 fallback compatible for CSI controller
ARM: dts: sun8i-h3: nanopi-m1-plus: enable HDMI
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Libre Computer ALL-H3-CC H5 is one of the few boards that can have
its eMMC run at HS-DDR speed mode. Mark it as such.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
On these A64 devices, the DC input jacks are wired to the ACIN pins of
the PMIC, which is represented by the AC power supply. With the
exception of the Nanopi A64, all devices include LiPo batteries or have
connectors for them, which are represented by the battery power supply.
Enable these power supplies in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
A few small improvements for the A64 this cycle:
- ARM PMU added
- Allwinner ARM architected timer workaround enabled
This works around timer value wrapping found in the Allwinner
implementation of the ARM architected timer.
-----BEGIN PGP SIGNATURE-----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=kZwf
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner DT64 changes for 5.1
A few small improvements for the A64 this cycle:
- ARM PMU added
- Allwinner ARM architected timer workaround enabled
This works around timer value wrapping found in the Allwinner
implementation of the ARM architected timer.
* tag 'sunxi-dt64-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: Enable A64 timer workaround
arm64: dts: allwinner: a64: Fix a typo
arm64: dts: allwinner: a64: Add PMU node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The 'arm,armv8' compatible string is only for software models. It adds
little value otherwise and is inconsistently used as a fallback on some
platforms. Remove it from those platforms.
This fixes warnings generated by the DT schema.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Chanho Min <chanho.min@lge.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a node for H6 SRAM C1 section.
Manual calls it VE SRAM, but for consistency with older SoCs, SRAM C1
name is used.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add dts node details for Allwinner A64 CSI controller.
A64 CSI has similar features as like in H3, but the CSI_SCLK
need to update it to 300MHz than default clock rate.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The GIC device node was placed out of order in the initial device tree
submission. Move it so the nodes are correctly sorted by base address
again.
Fixes: e54be32d02 ("arm64: allwinner: h6: add the basical Allwinner H6 DTSI file")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As instability in the architectural timer has been observed on multiple
devices using this SoC, inluding the Pine64 and the Orange Pi Win,
enable the workaround in the SoC's device tree.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This typo inverted the meaning of the comment, but the rest of the
comment and the code reveal that the regulator in question needs to be
on at all times.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Currently, AXP803 driver assumes that reg_drivevbus is input which is
wrong. Unfortunate consequence of that is that none of the USB ports
work on the board, even USB HOST port, because USB PHY driver probing
fails due to missing regulator.
Fix that by adding "x-powers,drive-vbus-en" property to AXP803 node.
Fixes: 14ff5d8f91 ("arm64: dts: allwinner: a64: Orange Pi Win: Enable USB OTG socket")
Cc: stable@vger.kernel.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
When introducing the video-codec node for the video engine, the
compatible for the H5 was used instead of the compatible for the
A64. Use the right compatible instead.
Fixes: d60ce24740 ("arm64: dts: allwinner: a64: Add Video Engine node")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This is necessary to use 'perf' for cache profiling etc.
Tested on Teres I Laptop.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Bluetooth using a Broadcom (now Cypress) chip connected to an UART on
the Bananapi M64 is enabled using serdev and the updated bindings for
Broadcom Bluetooth. The patch series had been sitting on the mailing
lists for a month, and the driver bits were just merged on 2018/12/19.
-----BEGIN PGP SIGNATURE-----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=Ks3Q
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner arm64 DT changes for 4.21 - round 2
Bluetooth using a Broadcom (now Cypress) chip connected to an UART on
the Bananapi M64 is enabled using serdev and the updated bindings for
Broadcom Bluetooth. The patch series had been sitting on the mailing
lists for a month, and the driver bits were just merged on 2018/12/19.
* tag 'sunxi-dt64-for-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: bananapi-m64: Add Bluetooth device node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side
identifies as BCM43430, while the Bluetooth side identifies as BCM43438.
The Bluetooth side is connected to UART1 in a 4 wire configuration. Same
as the WiFi side, due to being the same chip and package, DLDO2 provides
overall power via VBAT, and DLDO4 provides I/O power via VDDIO. The RTC
clock output provides the LPO low power clock at 32.768 kHz.
This patch enables Bluetooth on this board, and also adds the missing
LPO clock on the WiFi side. There is also a PCM connection for Bluetooth,
but this is not covered here.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Our usual pull request with the changes shared between the H3 and H5 SoCs.
The major changes for this release are:
- Addition of the video engine for the H5
- H3 Camera support
- New board: Emlid Neutis N5, Mapleboard MP130
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXAqJJwAKCRDj7w1vZxhR
xTq4AP9SxrPeKDTBD4mKV+PVuJ2qq919M6o+mcxDkCecEMfbagD+JLkt2uGzdpb8
eC6CuieHvJq1y/akfDpRBf0ZZD0/bw0=
=yRd0
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner H3/H5 changes for 4.21
Our usual pull request with the changes shared between the H3 and H5 SoCs.
The major changes for this release are:
- Addition of the video engine for the H5
- H3 Camera support
- New board: Emlid Neutis N5, Mapleboard MP130
* tag 'sunxi-h3-h5-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h5: Add Video Engine node
ARM/arm64: dts: allwinner: Move H3/H5 syscon label over to soc-specific nodes
arm64: dts: allwinner: h5: Add system-control node with SRAM C1
ARM: dts: sun8i: h3: Fix the system-control register range
ARM: dts: sun8i: Add the H3/H5 CSI controller
ARM: dts: sun8i-h3: Add dts for the Mapleboard MP130
arm64: dts: allwinner: new board - Emlid Neutis N5
dt-bindings: vendor-prefix: new vendor - Emlid
ARM: dts: sun8i-h3: add sy8106a to orange pi plus
Signed-off-by: Olof Johansson <olof@lixom.net>
Our usual set of arm64 DT changes, with the biggest additions being:
- Support for the video decoding engine in the A64
- Support for the audio codec in the A64
- USB Support in the H6
- HDMI Support in the H6
- EMAC Support in the H6
- New board: Orange Pi Lite2
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXAqGvQAKCRDj7w1vZxhR
xeObAQDZGMVjFjiWlC0jYjBQoCHMf1dlu6iPd4qe8h3GS1XUVQD/c8SJaMj5oLX1
HKjtqQD+sJRUQdcWlwAsqEEKyKUhfQs=
=aAr3
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner arm64 DT changes for 4.21
Our usual set of arm64 DT changes, with the biggest additions being:
- Support for the video decoding engine in the A64
- Support for the audio codec in the A64
- USB Support in the H6
- HDMI Support in the H6
- EMAC Support in the H6
- New board: Orange Pi Lite2
* tag 'sunxi-dt64-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (27 commits)
arm64: dts: allwinner: a64: Fix up RTC device node and clock references
arm64: dts: allwinner: a64: Add Video Engine node
arm64: dts: allwinner: a64: Add support for the SRAM C1 section
arm64: dts: allwinner: a64: pinebook: enable power supplies
arm64: dts: allwinner: a64: sopine-baseboard: enable power supplies
arm64: dts: allwinner: axp803: add AC and battery power supplies
arm64: dts: allwinner: a64: bananapi-m64: Enable audio codec
arm64: dts: allwinner: a64: enable sound on Pinebook
arm64: dts: allwinner: a64: enable sound on Pine64 and SoPine
arm64: dts: allwinner: a64: add nodes necessary for analog sound support
arm64: dts: allwinner: h6: orangepi: Add device nodes for LEDs
arm64: dts: allwinner: h6: orangepi: Enable USB 2.0 host and OTG ports
arm64: dts: allwinner: h6: orangepi: Add board-wide 5V regulator
arm64: dts: allwinner: h6: fix EMAC compatible string sequence
arm64: dts: allwinner: a64: Add device node for Mali-400 GPU
dt-bindings: gpu: mali-utgard: Add compatible for A64 Mali
arm64: dts: allwinner: h6: enable USB2 on Pine H64
arm64: dts: allwinner: h6: add USB Vbus regulator for Pine H64
arm64: dts: allwinner: h6: add USB2-related device nodes
arm64: dts: allwinner: h6: Enable HDMI output on Pine H64 board
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The RTC module on the A64 was claimed to be the same as on the A31, when
in fact it is not. It is actually compatible to the H3's RTC. The A64's
RTC has some extra crypto-related registers which the H3's does not, but
the exact function of these is not clear.
This patch fixes the compatible string and clock properties to conform
to the updated bindings. The device node for the internal oscillator is
removed, as it is internalized into the RTC device. Clock references to
the IOSC and LOSC are also fixed.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The RTC module on the H3 was claimed to be the same as on the A31, when
in fact it is not. The A31 does not have an RTC external clock output,
and its internal RC oscillator's average clock rate is not in the same
range. The H5's RTC has some extra crypto-related registers compared to
the H3. Their exact functions are not clear. Also the RTC-VIO regulator
has different settings.
This patch fixes the compatible string and clock properties to conform
to the updated bindings. The device node for the internal oscillator is
removed, as it is internalized into the RTC device. Clock references to
the IOSC and LOSC are also fixed.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This adds the Video Engine node for the A64. Since it can map the whole
DRAM range, there is no particular need for a reserved memory node
(unlike platforms preceding the A33).
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the description for the SRAM C1 section to the A64 device-tree.
Since there is no entry for this section in the A64 manual, the base
address and size were only verified to be consistent empirically.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds the Video Engine node for the H5. Since it can map the whole
DRAM range, there is no particular need for a reserved memory node
(unlike platforms preceding the A33).
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The EMAC driver requires a syscon node to access the EMAC clock
configuration register (that is part of the system-control register
range and controlled). For this purpose, a dummy syscon node was
introduced to let the driver access the register freely.
Recently, the EMAC driver was tuned to get access to the register when
the SRAM driver is registered (as used on the A64). As a result, it is
no longer necessary to have a dummy syscon node for that purpose.
Now that we have a proper system-control node for both the H3 and H5,
we can get rid of that dummy syscon node and have the EMAC driver use
the node corresponding to the proper SRAM driver (by switching the
syscon label over to each dtsi). This way, we no longer have two
separate nodes for the same register space.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the H5-specific system control node description to its device-tree
with support for the SRAM C1 section, that will be used by the video
codec node later on.
The CPU-side SRAM address was obtained empirically while the size was
taken from the documentation. They may not be entirely accurate.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
AXP803 ACIN pins are routed from SOM to the DC jack on the baseboard.
AXP803 charger pins BATSENSE, LOADSENSE, N_BATDRV, LX_CHG, VIN_CHG
and IPSOUT are connected via PMOS driver to SOM VBAT pins. VBAT and
AXP803 TS pins are routed to the baseboard 3-pin battery connector.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Parts of the AXP803 are compatible with their counterparts on the AXP813.
Add DT nodes ADC, GPIO, AC and battery power supplies.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This patch enables audio via the SoC's internal audio codec. All
relevant device nodes are enabled, and the routing is set to match
the board design. MIC1 is routed to an onboard microphone, with MBIAS
providing power. MIC2 and HP are routed to the 3.5mm headset TRRS jack.
No phantom power is provided to the headset microphone.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Pinebook has a headphone jack tied to the HP headphone output of
the SoC, and internal speakers connected to the LINEOUT of the SoC,
through a standalone amplifier.
This commit enables I2S, digital and analog parts of audio codec on
Pinebook, along with a device node for the external amplifier.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[wens@csie.org: dropped headphone_amp; added headphone amp regulator supply;
fixed speaker_amp node name and sound-name-prefix name]
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This commit enables I2S, digital and analog parts of audiocodec on
Pine64 and SoPine boards.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[wens@csie.org: Dropped headphone_amp; added headphone amp regulator supply]
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add nodes for i2s, digital and analog parts of audiocodec on A64.
The routing paths listed are entries connecting the digital and analog
side of the audio codec together. Due to how device tree works, these
must be copied over to each board device tree, in addition to any board
level routes.
The oversampling rate is set to 128, so that when playing back 192 kHz
audio samples, the MCLK runs at the same rate as the module clock, at
24.576 MHz.
The user manual suggests using different oversampling rates for different
sample rates, but that's not possible without a platform-specific machine
driver.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[wens@csie.org: Lowered oversampling rate to 128; expanded commit message]
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Lite 2 and Orange Pi One Plus both have two LEDs, one red
and one green. These are driven directly by GPIO lines in an active high
arrangement. The red LED is labeled "power", so it is set to be on by
default.
Note that the default drive current for the GPIO lines makes the LEDs
very bright.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Orange Pi Lite 2 and Orange Pi One Plus share the same design for
their USB 2.0 ports. VBUS is directly tied to the board wide 5V rail,
which is also directly tied to the DC jack. There is no current limiting
in this design.
This patch enables all the USB 2.0 related device nodes, and sets the
VBUS regulator supplies and OTG ID detection GPIO.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Orange Pi Lite 2 and Orange Pi One Plus share the same design for
their USB 2.0 ports. VBUS is directly tied to the board wide 5V rail,
which is also directly tied to the DC jack. There is no current limiting
in this design. This 5V rail also supplies the various inputs to the
PMIC.
This patch adds a board wide 5V regulator and sets it as the input to
the PMIC inputs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The SoC-specific compatible should come before the fallback compatible
string when multiple compatible strings are present, but the sequence is
wrong currently on H6 EMAC node (A64 fallback before H6 compatible).
Fix the sequence.
Fixes: c8ced5516d ("arm64: allwinner: h6: add EMAC device nodes")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add support for Allwinner A64 has Mali-400MP2.
All interrupt lines are mentioned in the manual so used the same.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pine H64 board has both the USB2 OTG pins and the USB2 host pins on H6
SoC wired out to USB Type-A ports.
Enable them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The 5V output of the USB ports on Pine H64 is controlled via a GPIO.
Add the USB Vbus regulator device tree node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Allwinner H6 has two USB2 ports, one OTG and one host-only.
Add device tree nodes related to them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Pine H64 board has HDMI type A connector.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This commit adds all entries needed for HDMI to function properly.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[added DE3 bus]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
OrangePi Lite2 is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- AP6356S Wifi/BT
- USB 2.0, USB 3.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Based on the information from hardware schematics and orangepi
vendor orangepi H6 boards, One Plus and Lite2 shares common nodes
like axp805, uart, mmc0 etc. The common differences between them is
- One Plus, has Ethernet
- Lite2, has Wifi, USB3, CSI port.
So, add common orangepi nodes into sun50i-h6-orangepi.dtsi so-that
it case use on respective orangepi h6 board dts files.
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Pine H64 board has an Ethernet port, which is connected to a
RTL8211E PHY, then the PHY is connected to the MAC on H6 SoC.
Add support for the Ethernet port.
The PHY needs some time to start up, and the time is modelled as enable
ramp delay of the regulator.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 SoC has an EMAC like the one in A64.
Add device tree nodes for the H6 DTSI file.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
module, DDR3 RAM and eMMC.
- add neutis n5 dtsi file for SoM needs
- add neutis devboard dts file
- add neutis devboard target to dtb makefile
Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Backlight power is controlled by PH6 GPIO, so add corresponding
regulator-fixed node for it. Otherwise backlight won't light up
if bootloader doesn't enable it.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
There are close to 800 indivudal changesets in this branch again, which
feels like a lot. There are particularly many changes for the NVIDIA
Tegra platform this time, in fact more than it has seen in the two years
since the v4.9 merge window. Aside from this, it's been fairly normal,
with lots of changes going into Renesas R-CAR, NXP i.MX, Allwinner Sunxi,
Samsung Exynos, and TI OMAP.
Most of the changes are for adding new features into existing boards,
for brevity I'm only mentioning completely new machines and SoCs here.
For the first time I think we have (slightly) more new 64-bit hardware
than 32-bit:
Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5
is a minor variation of the motherboards of the GTA04 phone, see
https://shop.goldelico.com/wiki.php?page=GTA04A5
Clearfog is a nice little board for quad-core
Marvell Armada 8040 network processor, see
https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/
Two additional server boards come with the Aspeed baseboard management
controllers: Stardragon4800 is an arm64 reference platform made by HXT
(based on Qualcomm's server chips), and TiogaPass is an Open Compute
mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in
the BMC.
NXP i.MX usually sees a lot of new boards each release. This time there
we only add one minor variant: ConnectCore 6UL SBC Pro uses the same
SoM design as the ConnectCore 6UL SBC Express added later. However,
there is a new chip, the i.MX6ULZ, which is an even smaller variant
of the i.MX6ULL, with features removed. There is also support for the
reference board design, the i.MX6ULZ 14x14 EVK.
A new Raspberry Pi variant gets added, this one is the CM3 compute module
based on bcm2837, it was launched in early 2017 but only now added to
the kernel, both as 32-bit and as 64-bit files, as we tend to do for
Raspberry Pi.
On the Allwinner side, everything is again about cheap development
boards, usually of the "Fruit Pi" variety. The new ones this time
are:
Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
The last one of these is now a 64-bit version of the earlier Banana
Pi M2+ H3, with the same board layout.
Similarly, for Rockchips, get get another variant of the 32-bit
Asus Tinker board, the model 'S' based on rk3288, and three now
boards based on the popular RK3399 chip:
ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
Rock960: https://www.96boards.org/product/rock960/
RockPro64: https://www.pine64.org/?page_id=61454
These are all quite powerful boards with lots of RAM and I/O, and
the RK3399 is the same chip used in several Chromebooks. Finally,
we get support for the PX30 (aka rk3326) chip, which is based on the
low-end 64-bit Cortex-A35 CPU core. So far, only the evaluation board
is supported.
One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is based
on the MT7622 WiFi router platform, and the first product I've seen with
a 64-bit Mediatek chip in that market: http://www.banana-pi.org/r64.html
For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
development board, which are similar to the Hi3660 and Hikey 360
respectively, but add support for an NPU.
Amlogic gets initial support for the Meson-G12A chip (S905D2),
another quad-core Cortex-A53 SoC, and its evaluation platform.
On the 32-bit side, we gain support for an actual end-user product,
the Endless Computers Endless Mini based on Meson8b (S805), see
https://endlessos.com/computers/
Qualcomm adds support for their MSM8998 SoC and evaluation platform. This
chip is commonly known as the Snapdragon 835, and is used in high-end
phones as well as low-end laptops.
For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
but no boards for this one. However, we do add boards for the previously
added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the M3NULCB
Starter Kit Pro.
While we have lots of DT changes for NVIDIA to update the existing files,
the only board that gets added is the Toradex Colibri T20 on Colibri
Evaluation Board for the old Tegra2.
Synaptics add support for their AS370 SoC, which is part of the (formerly
Marvell) Berlin line of set-top-box chips used e.g. in the various Google
Chromecast. Only the .dtsi gets added at this point, no actual machines.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJb1224AAoJEGCrR//JCVIn9uYP/jLMoGkVQRS5L9sRjOci1l5b
EHl8veJ+uNJaTStp5XAZk90MoBcSdXtnISSEiR7a3qKJw1mYfgAWyPtQCttRFUCo
rDp4GJpJ96TBg1tyt5Lop3V9eIYbCh9epf2foKTTdpRiX022AFk1031jvnh2Teuy
fKA2VNeoyyOZqxh0ysJq7G8kWt8PTQTKXDebYPWEbsu0AFmqQ84lz7oGNdPk0GPm
krtQIO6rh+sJR/8wWGYfnTYAIOk6jNrPhiyjEcyu+x2525rwKxJNKVY8P9PuNhrl
hzqld1dPtb3gfdcxWxZUznHmVUGkVEIa1QNC6csSmLzuxqJJE0/J5u2P8lIfrhVI
c5C8r3eaTxFM0s5uKhNhhewlJ6uiDhUQy13AG0JXteujP23BGObYstnV10pJrH75
xq7uSUiU04v95MocPjodJ2I7dIlAoFCd6ELnsmD/mz743gY9AZ6DHaOBMMwIzK3H
EQifF5E/4PWOjBx7fonumBm0LebPjWGmv4CNyCK5Q93ylK7U/kFDdjiNjNhyks5E
CVQBFhA7sshKJQRDOiaofMxOfKJHeKGU2PR7yGRpT3YWQD/apIL/elG4qUNjLX46
2Dwdgq8nDdbY2SzPwwy7ncTtyDRYcsFCtScT5slu1I1UxIhwEYJurzCKDM4jJNZb
Cg2D7a+AlZ8N5Vsr1ldV
=yaED
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"There are close to 800 indivudal changesets in this branch again,
which feels like a lot. There are particularly many changes for the
NVIDIA Tegra platform this time, in fact more than it has seen in the
two years since the v4.9 merge window. Aside from this, it's been
fairly normal, with lots of changes going into Renesas R-CAR, NXP
i.MX, Allwinner Sunxi, Samsung Exynos, and TI OMAP.
Most of the changes are for adding new features into existing boards,
for brevity I'm only mentioning completely new machines and SoCs here.
For the first time I think we have (slightly) more new 64-bit hardware
than 32-bit:
Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5 is a
minor variation of the motherboards of the GTA04 phone, see
https://shop.goldelico.com/wiki.php?page=GTA04A5
Clearfog is a nice little board for quad-core Marvell Armada 8040
network processor, see
https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/
Two additional server boards come with the Aspeed baseboard management
controllers: Stardragon4800 is an arm64 reference platform made by HXT
(based on Qualcomm's server chips), and TiogaPass is an Open Compute
mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in the
BMC.
NXP i.MX usually sees a lot of new boards each release. This time
there we only add one minor variant: ConnectCore 6UL SBC Pro uses the
same SoM design as the ConnectCore 6UL SBC Express added later.
However, there is a new chip, the i.MX6ULZ, which is an even smaller
variant of the i.MX6ULL, with features removed. There is also support
for the reference board design, the i.MX6ULZ 14x14 EVK.
A new Raspberry Pi variant gets added, this one is the CM3 compute
module based on bcm2837, it was launched in early 2017 but only now
added to the kernel, both as 32-bit and as 64-bit files, as we tend to
do for Raspberry Pi.
On the Allwinner side, everything is again about cheap development
boards, usually of the "Fruit Pi" variety. The new ones this time are:
- Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
- Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
- Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
- Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
The last one of these is now a 64-bit version of the earlier Banana Pi
M2+ H3, with the same board layout.
Similarly, for Rockchips, get get another variant of the 32-bit Asus
Tinker board, the model 'S' based on rk3288, and three now boards
based on the popular RK3399 chip:
- ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
- Rock960: https://www.96boards.org/product/rock960/
- RockPro64: https://www.pine64.org/?page_id=61454
These are all quite powerful boards with lots of RAM and I/O, and the
RK3399 is the same chip used in several Chromebooks. Finally, we get
support for the PX30 (aka rk3326) chip, which is based on the low-end
64-bit Cortex-A35 CPU core. So far, only the evaluation board is
supported.
One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is
based on the MT7622 WiFi router platform, and the first product I've
seen with a 64-bit Mediatek chip in that market:
http://www.banana-pi.org/r64.html
For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
development board, which are similar to the Hi3660 and Hikey 360
respectively, but add support for an NPU.
Amlogic gets initial support for the Meson-G12A chip (S905D2), another
quad-core Cortex-A53 SoC, and its evaluation platform. On the 32-bit
side, we gain support for an actual end-user product, the Endless
Computers Endless Mini based on Meson8b (S805), see
https://endlessos.com/computers/
Qualcomm adds support for their MSM8998 SoC and evaluation platform.
This chip is commonly known as the Snapdragon 835, and is used in
high-end phones as well as low-end laptops.
For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
but no boards for this one. However, we do add boards for the
previously added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the
M3NULCB Starter Kit Pro.
While we have lots of DT changes for NVIDIA to update the existing
files, the only board that gets added is the Toradex Colibri T20 on
Colibri Evaluation Board for the old Tegra2.
Synaptics add support for their AS370 SoC, which is part of the
(formerly Marvell) Berlin line of set-top-box chips used e.g. in the
various Google Chromecast. Only the .dtsi gets added at this point, no
actual machines"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (721 commits)
ARM: dts: socfgpa: remove ethernet aliases from dtsi
arm64: dts: stratix10: add ethernet aliases
dt-bindings: mediatek: Add bindig for MT7623 IOMMU and SMI
dt-bindings: mediatek: Add JPEG Decoder binding for MT7623
dt-bindings: iommu: mediatek: Add binding for MT7623
dt-bindings: clock: mediatek: add support for MT7623
ARM: dts: mvebu: armada-385-db-88f6820-amc: auto-detect nand ECC properites
ARM: dts: da850-lego-ev3: slow down A/DC as much as possible
ARM: dts: da850-evm: Enable tca6416 on baseboard
arm64: dts: uniphier: Add USB2 PHY nodes
arm64: dts: uniphier: Add USB3 controller nodes
ARM: dts: uniphier: Add USB2 PHY nodes
ARM: dts: uniphier: Add USB3 controller nodes
arm64: dts: meson-axg: s400: disable emmc
arm64: dts: meson-axg: s400: add missing emmc pwrseq
arm64: dts: clearfog-gt-8k: add PCIe slot description
ARM: dts: at91: sama5d4_xplained: even nand memory partitions
ARM: dts: at91: sama5d3_xplained: even nand memory partitions
ARM: dts: at91: at91sam9x5cm: even nand memory partitions
ARM: dts: at91: sama5d2_ptc_ek: fix bootloader env offsets
...
Our usual set of DT changes for the arm64 Allwinner SoCs.
The most notable things are:
- HDMI support on the A64
- New boards: OrangePi One Plus
-----BEGIN PGP SIGNATURE-----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=sPs9
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner arm64 DT changes for 4.20
Our usual set of DT changes for the arm64 Allwinner SoCs.
The most notable things are:
- HDMI support on the A64
- New boards: OrangePi One Plus
* tag 'sunxi-dt64-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (28 commits)
arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay
arm64: dts: allwinner: a64: Enable HDMI output on A64 boards w/ HDMI
arm64: dts: allwinner: a64: Add display pipeline
arm64: dts: allwinner: h6: add system controller device tree node
arm64: dts: allwinner: h6: Add OrangePi One Plus initial support
arm64: dts: allwinner: a64: Rename r_i2c_pins_a label to r_i2c_pl89_pins
arm64: dts: allwinner: a64: Rename uart0_pins_a label to uart0_pb_pins
arm64: dts: allwinner: a64: Split out data strobe pin from mmc2 pinmux
arm64: dts: allwinner: a64: NanoPi-A64: Add blue status LED
arm64: dts: allwinner: a64: NanoPi-A64: Add Wifi chip
arm64: dts: allwinner: a64: NanoPi-A64: Add Ethernet
arm64: dts: allwinner: a64: NanoPi-A64: Fix DCDC1 voltage
arm64: dts: allwinner: a64: Olinuxino: enable USB
arm64: dts: allwinner: a64: Olinuxino: add Ethernet nodes
arm64: dts: allwinner: a64: Olinuxino: fix DRAM voltage
arm64: dts: allwinner: a64: Orange Pi Win: Adjust CSI power rails
arm64: dts: allwinner: a64: Orange Pi Win: Add SPI flash node
arm64: dts: allwinner: a64: Orange Pi Win: Add SDIO node
arm64: dts: allwinner: a64: Orange Pi Win: Add LED node
arm64: dts: allwinner: a64: Orange Pi Win: Add UARTs
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Bananapi released an updated revision of the H3/H5 based Bananapi M2+.
Version 1.2 enables voltage control for the CPU's regulator by using
a GPIO line to toggle a MOSFET that can change the effective resistance
value in the regulator's feedback network.
This patch adds a common .dtsi file for this new revision, which
includes the original common sunxi-bananapi-m2-plus.dtsi file, and
adds the GPIO-controlled regulator and a cpu-supply reference. H3
and H5 variant dts files are added as well.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Bananapi M2 Plus H5 is a variant of the original Bananapi M2 Plus,
with the H3 SoC replaced with an H5. Everything else is the same.
Add a stub device tree incorporating the shared bananapi-m2-plus dtsi
file.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The H5 has a Mali-450 GPU with 4 Pixel Processor cores.
Interestingly, while the datasheet lists an interrupt line for the GPU's
PMU, the hardware block itself doesn't seem to have it. Reads from the
PMU address range all return zero, and writes are ignored.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The PHY found on the A64-OLinuXino requires a TX delay in order to
operate properly. Olimex uses a 600ps second delay in their BSP, and
that has been found to work, so let's use that value in the current
DT.
Signed-off-by: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Enable all necessary device tree nodes and add connector node to device
trees for all supported A64 boards with HDMI.
Jagan, tested on BPI-M64, OPI-Win, A64-Olinuxino, NPI-A64
Vasily, tested on pine64-lts
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Icenowy: squash all board patches altogether and change supply name]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Allwinner A64 have a display pipeline with 2 mixers/TCONs, the first
TCON is connected to LCD and the second is to HDMI.
The HDMI controller/PHY pair is similar to the one on H3/H5.
Add all required device tree nodes of the display pipeline, including
the TCON0 LCD one and the TCON1 HDMI one.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Icenowy: refactor commit message and add 1st pipeline]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
As we have already binding for the H6 system controller, add its node
to the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[fixed compatible string]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211
- USB 2.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The pinmux name and label for a specific function should denote which
pingroup it is on, or if there is only one option for the function, have
not enumerating prefix/suffix at all.
The "r_i2c_pins_a" label is renamed to "r_i2c_pl89_pins" to fit our
current style. The node name "i2c" is also changed to "r-i2c-pl89-pins"
to match. The reason for the peculiar name is that the other option for
muxing R_I2C is on the PL0/PL1 pins, so the name has to mention the pin
numbers in addition to the pingroup.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The pinmux name and label for a specific function should denote which
pingroup it is on, or if there is only one option for the function, have
not enumerating prefix/suffix at all.
The "uart0_pins_a" label is renamed to "uart0_pb_pins" to fit our
current style. The node name "uart0" is also changed to "uart0-pb-pins"
to match.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The eMMC 5.0 standard introduced the data strobe (DS) pin. This pin is
not used for pre-5.0 data modes, nor is it found on pre-5.0 eMMC chips.
On the A64, this pin is muxed with spi0's MISO pin. If the DS pin is
included in the mmc2 pinmux by default, this wil prevent the usage
of both mmc2 and spi0 together.
Instead, split out the DS pin to a separate pinmux that only gets used
by boards that actually have it wired up. Currently supported ones
include the Bananapi M64 and Pine64 Pinebook. These are fixed up.
Fixes: a3e8f49262 ("arm64: allwinner: a64: Add MMC pinctrl nodes")
Fixes: b8bcf0e1b2 ("arm64: allwinner: add BananaPi-M64 support")
Fixes: df35fbcfa3 ("arm64: dts: allwinner: add support for Pinebook")
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Beside the non-controllable green power LED, the NanoPi-A64 features a
blue "status" LED, connected to PD24.
Add the device tree node to make it usable.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The NanoPi-A64 has an on-board WiFi chip, connected to the usual MMC1 SDIO
interface. The AXP power line is the always-on VDD_SYS_3.3V, but it uses
pin L2 to enable the regulator.
As the actual WiFi driver is not in mainline Linux, it doesn't have a
compatible string, so we omit this from the node.
Add the respective nodes to the DT to make it usable.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[wens@csie.org: Add RTL8189ETV LPO clock to pwrseq node]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The NanoPi-A64 has the usual Realtek Gbit PHY connected to the EMAC,
so add the respective nodes to the DT. The PHY is powered by the
VDD_SYS_3.3V line, which is always on.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
According to the NanoPi-A64 schematics, DCDC1 is connected to a voltage
rail named "VDD_SYS_3.3V". All users seem to expect 3.3V here: the
Ethernet PHY, the uSD card slot, the camera interface and the GPIO pins
on the headers.
Fix up the voltage on the regulator to lift it up to 3.3V.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Olinuxino has two USB sockets:
USB0 is connected to a micro B socket. As it has the ID pin wired and
the VBUS line connected to the PMIC, we describe it as a proper OTG socket,
which switches between host and device automatically.
USB1 is connected to a normal USB A socket. PG9 enables the power line,
so add the required regulator as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add the DT nodes required to enable the Gigabit Ethernet on the board.
The PHY is powered by the always-on power rail VDD_SYS_3.3V (DCDC1).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Olinuxino board uses DDR3L chips which are supposed to be driven
with 1.35V. The reset default of the AXP is properly set to 1.36V.
While technically the chips can also run at 1.5 volts, changing the
voltage on the fly while booting Linux is asking for trouble. Also
running at a lower voltage saves power.
So fix the DCDC5 value to match the actual board design.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Martin Lucina <martin@lucina.net>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win board uses the AXP's ALDO1 power rail to drive the
VCC-CSI line, which, according to the schematic, needs to be set to 2.8V.
Also the ELDO3 power rail is connected to the CSI, with somewhat unclear
voltage requirements. Add this regulator and allow the voltage to be set
between 1.5V and 1.8V, which are the voltages mentioned in the
schematic.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win comes with 2 MB SPI flash, add the node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win features a soldered WiFi chip on the board, connected
via the SDIO interface. Add the required DT nodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has a green status LED, add the DT node for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win exposes several UARTs on header pins, and connects one
to the on-board WiFi/Bluetooth chip.
Add the pinmux definitions to the UART nodes, but keep them disabled.
Enable the UART1, which is wired to the Bluetooth chip, and add a serdev
node. There is no binding for the BT8723 yet, so leave this mostly empty
for now.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has the usual Gigabit PHY connected to the EMAC.
Its power is controlled by GPIO PD14.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has a micro USB-B socket, connected to the SoC's
USB-OTG port. Its power is supplied by the AXP PMIC, and the ID pin is
connected to GPIO PH9. It can serve both as a host or a client port.
Add the respective DT nodes to enable it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[wens@csie.org: enable paired EHCI/OHCI device nodes and regulator supply]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has four standard USB-A sockets, connected to an
on-board USB hub. The hub's and socket's power regulators are enabled by
GPIO PD7.
Add the regulator to the DT to enable the power supply.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has a microSD card slot which is connected via all
four SD data lines. As the DT was not mentioning this fact, we got the
default single bit transfers, losing out on performance.
Also, as microSD does not have a write protect switch, we disable this
feature in the DT node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Pine64-LTS is a variant of the Pine64 board, from the software
visible side resembling a SoPine module on a baseboard, though the
board has the SoC and DRAM integrated on one PCB.
Due to this it basically shares the DT with the SoPine baseboard, which
we mimic in our DT by inclucing the boardboard .dts into the new file,
just overwriting the model name.
Having a separate .dts for this seems useful, since we don't know yet if
there are subtle differences between the two. Also the SoC on the LTS
board is technically an "R18" instead of the original "A64", although as
far as we know this is just a relabelled version of the original SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Current kernels complain when booting on an A64 Soc:
....
[ 1.904297] cacheinfo: Unable to detect cache hierarchy for CPU 0
....
Not a real biggie on this flat topology, but also easy enough to fix.
Add the L2 cache node and let each CPU point to it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Currently the enabled MMC controllers on Pine H64 do not have bus-width
set, which make them fall back to 1-bit mode and become quite slow.
Fix this by add the corresponding bus-width properties.
Fixes: ecbd611882 ("arm64: allwinner: h6: enable MMC0/2 on Pine H64")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Another user of cd-inverted seems to have crept in. Switch it away from
cd-inverted to be consistent with other sunxi boards.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A64 have a SID controller which consist of EFUSE (starting at 0x200)
and three registers to read/write some of the protected efuses.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Pine H64 board have a MicroSD slot connected to MMC0 controller of
the H6 SoC and a eMMC slot connected to MMC2.
Enable them in the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner H6 SoC have 3 MMC controllers.
Add device tree nodes for them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
address-cells/size-cells is unnecessary for dwmac-sun8i node.
It was in early days, but since a mdio node is used, it could be
removed.
This patch fix the following DT warning:
Warning (avoid_unnecessary_addr_size): /soc/ethernet@1c50000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pine H64 board has an AXP805 PMIC on it, wired up in standalone, or
self-working, mode.
Enable it in the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Now that the device tree binding headers for the R_CCU have been merged,
we can use the macros, instead of raw numbers.
Switch to R_CCU macros for clock and reset indices.
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
On usual A64 board design the power of HDMI controller is connected to
DLDO1 of the AXP803 PMIC. If this regulator is shut down, the HDMI
output will be blank. Therefore the simplefb driver should keep this
regulator on.
Add the regulator to all currently available A64 boards' simplefb_hdmi
device node, if the board is capable of outputing HDMI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As the U-Boot bootloader now is also capable of initialize the HDMI on
A64 boards, add a simplefb device tree node for accessing the HDMI
framebuffer initialized by the bootloader.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As we have all necessary parts to enable the DE2 CCU on the Allwinner
A64 SoC, add the needed device tree nodes, including the DE2 CCU itself
and the DE2 bus.
The "mixer0-lcd0" simplefb device node is updated to use the DE2 CCU.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Pine H64 has 3 GPIO-controlled LEDs, which are labeled "heartbeat",
"link", and "status".
Add device nodes for them.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Currently all ARM kernels will have s2idle enabled if CONFIG_SUSPEND is
present. In this case if the lid is closed, systemd-logind will enter
s2idle mode by default; however there's no possible wakeup source
defined, so the system will enter a forever idle.
Add the lid itself as a wakeup source, thus the system can wakeup when
the lid is opened.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Originally the name of the DLDO3 regulator on TERES-I is "eDP12", which
is not consistent with other regulator names.
Change it to "vdd-edp", in order to make it more consistent.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The card detect GPIO for Sopine and Pine64-LTS is PF6.
Add this to the dts.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner A64 has a SRAM controller, and in the device tree currently
we have a syscon node to enable EMAC driver to access the EMAC clock
register. As SRAM controller driver can now export regmap for this
register, replace the syscon node to the SRAM controller device node,
and let EMAC driver to acquire its EMAC clock regmap.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[wens@csie.org: Updated compatible string]
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Pinebook is a A64-based laptop produced by Pine64, with the following
peripherals:
USB:
- Two external USB ports (one is directly connected to A64's OTG
controller, the other is under a internal hub connected to the host-only
controller.)
- USB HID keyboard and touchpad connected to the internal hub.
- USB UVC camera connected to the internal hub.
Power-related:
- A DC IN jack connected to AXP803's DCIN pin.
- A Li-Polymer battery connected to AXP803's battery pins.
Storage:
- An eMMC by Foresee on the main board (in the product revision of the
main board it's designed to be switchable).
- An external MicroSD card slot.
Display:
- An eDP LCD panel (1366x768) connected via an ANX6345 RGB-eDP bridge.
- A mini HDMI port.
Misc:
- A Hall sensor designed to detect the status of lid, connected to GPIO PL12.
- A headphone jack connected to the SoC's internal codec.
- A debug UART port muxed with headphone jack.
This commit adds basical support for it.
[vasily: squashed several commits into one, added simplefb node, added usbphy
to ehci0 and ohci0 nodes and other cosmetic changes to dts]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner A64 SoC features two PWM controllers, which are fully
compatible to the one used in the A13 and H3 chips.
Add the nodes for the devices (one for the "normal" PWM, the other for
the one in the CPUS domain) and the pins their outputs are connected to.
On the A64 the "normal" PWM is muxed together with one of the MDIO pins
used to communicate with the Ethernet PHY, so it won't be usable on many
boards. But the Pinebook laptop uses this pin for controlling the LCD
backlight.
On Pine64 the CPUS PWM pin however is routed to the "RPi2" header,
at the same location as the PWM pin on the RaspberryPi.
Tested on Pinebook and Teres-I
[vasily: fixed comment message as requested by Stefan Bruens, added default
muxing options to pwm and r_pwm nodes]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner A64 has a I2C controller, which is in the R_ MMIO zone and has
two groups of pinmuxes on PL bank, so it's called R_I2C.
Add support for this I2C controller and the pinmux which doesn't conflict
with RSB.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Outside of SOC few chips need external clock source
through RTC example Wifi chip. So RTC clock nodes to
phandle 32kHz external oscillator.
prefix rtc- with clock-output-names defined in
dt-binding to avoid confusion with existing osc32k name.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The OrangePi PC2 have an mx25l1606e spi flash.
Add a node for it.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Sopine and Pine64-LTS have a winbond w25q128 spi flash on spi0.
Add a node for it.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
We mostly have some changes to support the H6, Allwinner latest SoC. We're
still in the preliminary phase, with I2C, pinctrl and clock support.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE0VqZU19dR2zEVaqr0rTAlCFNr3QFAlsCsQwACgkQ0rTAlCFN
r3S9EhAAifnKDgAqWGuLR9xau3nK8CbjSLyFAba9ARdIuwxO3D0p6xgNkogve3o9
huwtx60TPfZeg86e5dqKmuC7gO/AKK0TaFDQcTXR4dEF6eH635J9yh1G5L6LjrLA
X9+EjuIL7a6HgolwyssRLLQETq3w5Pc+xMcoIc0J4ey0a4H8GjvXQWMzB+ytJWA1
Ykih6hMqJiR1VWbqSefx24+4X7RaBSwqu2S/GDk9Fi6Fabg5rbzH2tgolr0fK2BA
QtGx9LvJFsjpUwa2rOBom1EvEOoFri2ef3D06vOq8Nc0UA9G41JkWBXYczxRP1m5
0SEZUybyudIJMn+X3arEOklEEN5dsfzLnbpT7xWgjocPyt1foPtBYg/usPb8bvwn
k58j/nQDDrVPADEonbWmSBJ+5mtGl7pamJtm6GE0kCAe9eG8kLt0mkL5EH4X2Sq2
0P5q6HAjA866IACZzu4CRipXlBNCY+oMXSeaOkOYIfyIshNKkWPyxqim98FDtm6Y
66nfON3yXWOmbWwIW2z7HSJXpIn4L+qMD0OvTZWDISANQWybaKxeytVMcB65iEGQ
LzhfZi8K1tZdTN0cvsdKXrTTMnkcU4a1OZbDLe6vBPAengX219MYu1uCd+ArQ1Md
Rd1rjT+Nv2JpVTFV1AUgeoA1Yhu1Nw1zQTAu5y3d64HJCnybamU=
=d7Ql
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner arm64 changes for 4.18
We mostly have some changes to support the H6, Allwinner latest SoC. We're
still in the preliminary phase, with I2C, pinctrl and clock support.
* tag 'sunxi-dt64-for-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: h6: add PCF8563 RTC on Pine H64 board
arm64: allwinner: h6: add R_I2C controller
arm64: allwinner: h6: add R_INTC interrupt controller
arm64: allwinner: h6: add node for R_PIO pin controller
arm64: allwinner: h6: add PRCM CCU device node
arm64: dts: allwinner: a64: bananapi-m64: add usb otg
arm64: dts: allwinner: axp803: Add drivevbus regulator
arm64: allwinner: h6: restore the usage of CCU slice macros
Signed-off-by: Olof Johansson <olof@lixom.net>
Pine H64 board has a PCF8563 dedicated RTC connected to its R_I2C bus.
Enable the R_I2C bus and add the RTC to the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 SoC has a R_I2C controller wired to the PL0/PL1 pins, which
are used in the reference design to connect AXP805 PMIC.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 SoC has also a R_INTC interrupt controller like Allwinner
A64 SoC, but has its base address changed due to the memory map change
in H6.
Add it into the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 SoC has a R_PIO pin controller which controls PL and PM
GPIO banks.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 has also a PRCM CCU.
Add its device node into the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry
Pi B+ form factor single board computer based on the Allwinner H2+, H3,
or H5 SoCs with the same PCB.
The board has 2GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes
and connectors are in the exact same position as on the Raspberry Pi B+.
This patch enables the H5 variant using the H3 board definition moved to
a common dtsi in an earlier patch. The dts simply include the common dtsi
and declares the correct compatible and model of the H5 variant.
Suggested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The dtb entries for NanoPi boards in the device tree makefile somehow
ended up after the Orange Pi boards.
Move them so the list is properly sorted.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
At the board level, we want to be able to specify what regulator
supplies power to the cpu domain.
Add a label to the first cpu node so we can reference it later.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add usb otg support for bananapi-m64 board,
- USB-ID connected with PH9
- USB-DRVVBUS controlled by N_VBUSEN pin from PMIC
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add reg_drivevbus regualtor for boards which are using
external regulator to drive the OTG VBus through N_VBUSEN
PMIC pin.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
As the definition of CCU slice macros are already merged into the source
tree, restore the usage of the macros now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Here is our usual bunch of changes to the common DTSI shared between arm
and arm64, and their associated device trees.
Even though the diffstat is quite big, it's been mostly just cleanups. The
big feature is that the HDMI is now suported on H3 and H5 boards.
-----BEGIN PGP SIGNATURE-----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=hXvM
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner H3/H5 changes for 4.17" from Maxime Ripard:
Here is our usual bunch of changes to the common DTSI shared between arm
and arm64, and their associated device trees.
Even though the diffstat is quite big, it's been mostly just cleanups. The
big feature is that the HDMI is now suported on H3 and H5 boards.
* tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus
ARM: dts: sun8i-h3: Add Mali node
ARM64: dts: sun50i: h5: Enable HDMI output on H5 boards
ARM: dts: sun8i: h3: Enable HDMI output on H3 boards
ARM: dts: sunxi: h3/h5: Add HDMI pipeline
ARM: dts: sun8i: h2-plus: remove unnecessary mmc1_pins node
ARM: dts: sunxi: h3-h5: rename mmc0_pins_a and mmc1_pins_a
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc1 from dts to dtsi
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc0 from dts to dtsi
ARM: dts: sunxi: h3-h5: remove mmc0 card detection pin from pinctrl
ARM: dts: sun8i: h2+: add support for Banana Pi M2 Zero board
ARM: dts: sunxi: Switch MMC nodes away from cd-inverted property
ARM: dts: nanopi-neo-air: Add WiFi / eMMC
The Xunlong Orange Pi Zero Plus is single board computer.
- H5 Quad-core 64-bit Cortex-A53
- 512MB DDR3
- microSD slot
- Debug TTL UART
- 1000M/100M/10M Ethernet RJ45
- Realtek RTL8189FTV
- Spi flash (2MB)
- One USB 2.0 HOST, One USB 2.0 OTG
This is based on a patch from armbian:
https://github.com/armbian/build/blob/master/patch/kernel/sunxi-next/sunxi-add-orangepi-zero-plus.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The TERES-I is an open hardware laptop built by Olimex using the
Allwinner A64 SoC.
Add the board specific .dts file, which includes the A64 .dtsi and
enables the peripherals that we support so far.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A64 SoC features two display pipelines, one has a LCD output, the
other has a HDMI output.
Add support for simplefb for the LCD output. Tested on Teres I.
This patch was inspired by work of Icenowy Zheng.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add a watchdog node for the A64, automatically enabled on all boards.
Since the device is compatible with an existing driver, we only reserve
a new compatible string to be used together with the fall back.
Tested on Olimex Teres-I.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the proper pin group node to reference in board files.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pine H64 is an Allwinner H6-based SBC from Pine64, with the following
features:
- 1GiB/2GiB/4GiB LPDDR3 DRAM (in 4GiB situation only 3GiB is
accessible)
- AXP805 PMIC
- Raspberry-Pi-compatible GPIO header, "Euler" GPIO header (not
compatible with the "Euler" on Pine A64) and "Expansion" pin header
- 2 USB 2.0 ports and 1 USB 3.0 ports
- Audio jack
- MicroSD slot and eMMC module slot
- on-board SPI NOR flash
- 1Gbps Ethernet port (via RTL8211E PHY)
- HDMI port
Adds initial support for it, including the UART on the Expansion pin
header.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 is a new SoC with Cortex-A53 cores from Allwinner, with its
memory map fully reworked and some high-speed peripherals (PCIe, USB
3.0) introduced.
This commit adds the basical DTSI file of it, including the clock
support and UART support.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Enable HDMI output on all boards with HDMI connector.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Most of the boards use the mmc1 pins and their attributes defined in
mmc1_pins_a. Let's default to that by moving the pinctrl attributes to
the dtsi file. This makes it easier to modify device trees in the
future as there is only one place to change the pinctrl attributes.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the DAI blocks to the device tree. I2S0 and I2S1 are for
connecting to an external codec.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The S/PDIF transmitter can be reached on the Euler connector.
But as this is a GPIO then leave it disabled so that an overlay
can override the status property.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the device tree sound bindings for the S/PDIF block.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the SPDIF transceiver controller block and pin to the A64 dtsi.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Most of the boards use the mmc0 pins and their attributes defined in
mmc0_pins_a. Let's default to those by moving the pinctrl attributes
to the dtsi file. This makes it easier to modify device trees in the
future as there is only one place to change the pinctrl attributes.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
We get a moderate number of new machines this time, and only one
new SoC variant (Actions S700):
Actions:
S700 Soc and CubieBoard7 development board
Allo.com Sparky Single-board-computer
Allwinner:
Orange Pi R1 development board
Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
Axentia Nattis/Natte digital signage
sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
SolidRun Humminboard2 development board
Variscite DART-MX6 SoM and Carrier-board
Technologic TS-4600 and TS-7970 development board
Toradex Colibri iMX7D SoM board
v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
Moxa UC-8410A Series industrial computer
Gemini:
D-Link DNS-313 NAS enclosure
OMAP:
LogicPD OMAP35xx SOM-LV devkit
LogicPD OMAP35xx Torpedo devkit
Renesas:
r8a77970 (V3M) Starter Kit board
r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
Aspeed clk controller support
Freescale LS1088A, LS1021A device support
Gemini Ethernet, PCI, TVE, panel
Keystone gpio, qspi, more uarts
Mediatek cpufreq, regulator, clock, reset
Marvell thermal, cpufreq, nand
Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
Rockchip Mipi, GPU, display
Samsung Exynos5433 PMU, power domain, nfc
Spreadtrum: sc9860 clocks
Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qN1F
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"We get a moderate number of new machines this time, and only one new
SoC variant (Actions S700):
Actions:
- S700 Soc and CubieBoard7 development board
- Allo.com Sparky Single-board-computer
Allwinner:
- Orange Pi R1 development board
- Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
- Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
- Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
- Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
- Axentia Nattis/Natte digital signage
- sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
- SolidRun Humminboard2 development board
- Variscite DART-MX6 SoM and Carrier-board
- Technologic TS-4600 and TS-7970 development board
- Toradex Colibri iMX7D SoM board
- v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
- Moxa UC-8410A Series industrial computer
Gemini:
- D-Link DNS-313 NAS enclosure
OMAP:
- LogicPD OMAP35xx SOM-LV devkit
- LogicPD OMAP35xx Torpedo devkit
Renesas:
- r8a77970 (V3M) Starter Kit board
- r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
- Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
- Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
- Aspeed clk controller support
- Freescale LS1088A, LS1021A device support
- Gemini Ethernet, PCI, TVE, panel
- Keystone gpio, qspi, more uarts
- Mediatek cpufreq, regulator, clock, reset
- Marvell thermal, cpufreq, nand
- Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
- Rockchip Mipi, GPU, display
- Samsung Exynos5433 PMU, power domain, nfc
- Spreadtrum: sc9860 clocks
- Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ..."
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (690 commits)
arm64: dts: stratix10: fix SPI settings
ARM: dts: socfpga: add i2c reset signals
arm64: dts: stratix10: add USB ECC reset bit
arm64: dts: stratix10: enable USB on the devkit
ARM: dts: socfpga: disable over-current for Arria10 USB devkit
ARM: dts: Nokia N9: add support for up/down keys in the dts
ARM: dts: nomadik: add interrupt-parent for clcd
ARM: dts: Add ethernet to a bunch of platforms
ARM: dts: Add ethernet to the Gemini SoC
ARM: dts: rename oxnas dts files
ARM: dts: s5pv210: add interrupt-parent for ohci
ARM: lpc3250: fix uda1380 gpio numbers
ARM: dts: STi: Add gpio polarity for "hdmi,hpd-gpio" property
ARM: dts: dra7: Reduce shut down temperature of non-cpu thermal zones
ARM: dts: n900: Add aliases for lcd and tvout displays
ARM: dts: Update ti-sysc data for existing users
ARM: dts: Fix smartreflex compatible for omap3 shared mpu-iva instance
arm64: dts: marvell: armada-80x0: Fix pinctrl compatible string
arm: spear13xx: Fix spics gpio controller's warning
arm: spear13xx: Fix dmas cells
...
A few improvements to our DT support, with:
- basic DRM support for the A83t
- simplefb support for the H3 and H5 SoCs
- One fix for the USB ethernet on the Orange Pi R1
-----BEGIN PGP SIGNATURE-----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=bDG2
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.16, bis
A few improvements to our DT support, with:
- basic DRM support for the A83t
- simplefb support for the H3 and H5 SoCs
- One fix for the USB ethernet on the Orange Pi R1
* tag 'sunxi-dt-for-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a711: Enable the LCD
ARM: dts: sun8i: a83t: Add LVDS pins group
ARM: dts: sun8i: a83t: Enable the PWM
ARM: dts: sun8i: a83t: Add display pipeline
ARM: sunxi: h3/h5: add simplefb nodes
arm64: allwinner: h5: add compatible string for DE2 CCU
ARM: sun8i: h3/h5: add DE2 CCU device node for H3
dt-bindings: simplefb-sunxi: add pipelines for DE2
ARM: dts: sun8i: fix USB Ethernet of Orange Pi R1
Signed-off-by: Olof Johansson <olof@lixom.net>
The DE2 CCU on Allwinner H5 SoC has a slightly different behavior than
the one on H3, so the compatible string is not set in the common DTSI
file.
Add the compatible string of H5 DE2 CCU in H5 DTSI file.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Bananapi-M64 has 3 LEDS in red, green, and blue. These are toggled
via GPIO lines, which drive transistors that control current across the
LEDS. The red LED is by default on, via an additional pull-up on the
control line. We consider this means that it is a power indicator.
So we set the "default-on" property for it.
The pingroups the GPIO lines belong to require external regulators be
enabled to be able to drive the GPIO high. These regulators also have
other purposes. However the pin controller does not have bindings for
regulators. Here we just set them to always-on.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The sdcard detect pin on orange-pi-zero-plus2 is pulled up.
Fix cd-gpio description to enable sdcard detect.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since current tree support AXP803 regulators,
replace fixed regulator vcc3v3 with AXP803 dcdc1 regulator where ever
it need to replace.
Tested mmc0 on sopine baseboard.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
add arm64 H5 dwmac-sun8i support for this board
Signed-off-by: Antony Antony <antony@phenome.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
PF6 is mostly used as the CD pin for the microSD slot on H5 based
boards. So far we were referencing this pin twice: once using the
mmc0_cd_pin phandle, and then again directly as a GPIO via the pinctrl
phandle.
This will cause problems if the pinctrl driver enables strict mode, as
the second request will fail now, leading to a driver init failure.
Remove the redundant pin reference via the mmc0_cd_pin phandle.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Chris Obbard <obbardc@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On several A64 boards the Ethernet PHY is powered by the DC1SW regulator
on the AXP803 PMIC.
Add phy-handle property to these boards' emac node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Corentin LABBE <clabbe.montjoie@gmail.com>
Tested-by: Corentin LABBE <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable AXP803 PMIC and regulators for Orangepi Win.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We add device tree files for a couple of additional SoCs in various areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for networking,
Amlogic A113D for audio, and Renesas R-Car V3M for automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX, Amlogic
and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues that
the latest version of 'dtc' now warns about. Unfortunately there is still
a lot left to do.
A rework of the ARM foundation model introduced several new files
for common variations of the model.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TnSo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Arnd Bergmann:
"We add device tree files for a couple of additional SoCs in various
areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for
networking, Amlogic A113D for audio, and Renesas R-Car V3M for
automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX,
Amlogic and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues
that the latest version of 'dtc' now warns about. Unfortunately there
is still a lot left to do.
A rework of the ARM foundation model introduced several new files for
common variations of the model"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (599 commits)
arm64: dts: uniphier: route on-board device IRQ to GPIO controller for PXs3
dt-bindings: bus: Add documentation for the Technologic Systems NBUS
arm64: dts: actions: s900-bubblegum-96: Add fake uart5 clock
ARM: dts: owl-s500: Add CubieBoard6
dt-bindings: arm: actions: Add CubieBoard6
ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock
ARM: dts: owl-s500: Set power domains for CPU2 and CPU3
arm: dts: mt7623: remove unused compatible string for pio node
arm: dts: mt7623: update usb related nodes
arm: dts: mt7623: update crypto node
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
...
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing memory
leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node. The
prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to dtb
compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage Technology,
shimafuji, Tecon Microprocessor Technologies, DH electronics GmbH,
Opal Kelly, and Next Thing
-----BEGIN PGP SIGNATURE-----
iQItBAABCAAXBQJaCwaSEBxyb2JoQGtlcm5lbC5vcmcACgkQ+vtdtY28YcNzeA/8
C8uQhSsX2+UQZvFzcEA8KQAMGT3kYdrcf+gidRKwCEUWg1qscUEpTb3n3Rm5NUbU
RPD1s6GSlh6fJCMHDTQ6Tti/T59L7nZa2/AIGmUishGu4x4q1o18AobpFJmYP/EM
SJPwnmm5RV9WcZFao1y+sY3Xtn8DStxHO4cS+dyF5/EvPN9D8nbLJfu7bgTBAZww
HktIMB9kx+GTipRQZBvBwXoy5MJjthIZub4XwzesA4tGananj4cXlc0xaVxpdYy3
5bO6q5F7cbrZ2uyrF+oIChpCENK4VaXh80m0WHc8EzaG++shzEkR4he1vYkwnV+I
OYo4vsUg9dP8rBksUG1eYhS8fJKPvEBRNP7ETT5utVBy5I/tDEbo/crmQZRTIDIC
hZbhcdZlISZj0DzkMK2ZHQV9UYtRWzXrJbZHFIPP12GCyvXVxYJUIWb9iYnUYSon
KugygsFSpZHMWmfAhemw5/ctJZ19qhM5UIl2KZk5tMBHAf466ILmZjg0me6fYkOp
eADfwHJ1dLMdK79CVMHSfp+vArcZXp35B16c3sWpJB36Il97Mc/9siEufCL4GKX7
IBBnQBlbpSBKBejWVyI7Ip/Xp5u4qAQD+ZMJ9oLqBRqfWerHbDuOERlEOgwGqJYr
9v4HvP7V8eVUvAdqXka4EBfCyAgUzXDAxG2Dfmv9vGU=
=jgpN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
If CONFIG_OF_ALL_DTBS is enabled, "make ARCH=arm64 dtbs" compiles each
DTB twice; one from arch/arm64/boot/dts/*/Makefile and the other from
the dtb-$(CONFIG_OF_ALL_DTBS) line in arch/arm64/boot/dts/Makefile.
It could be a race problem when building DTBS in parallel.
Another minor issue is CONFIG_OF_ALL_DTBS covers only *.dts in vendor
sub-directories, so this broke when Broadcom added one more hierarchy
in arch/arm64/boot/dts/broadcom/<soc>/.
One idea to fix the issues in a clean way is to move DTB handling
to Kbuild core scripts. Makefile.dtbinst already recognizes dtb-y
natively, so it should not hurt to do so.
Add $(dtb-y) to extra-y, and $(dtb-) as well if CONFIG_OF_ALL_DTBS is
enabled. All clutter things in Makefiles go away.
As a bonus clean-up, I also removed dts-dirs. Just use subdir-y
directly to traverse sub-directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[robh: corrected BUILTIN_DTB to CONFIG_BUILTIN_DTB]
Signed-off-by: Rob Herring <robh@kernel.org>
We need to add "clean-files" in Makfiles to clean up DT blobs, but we
often miss to do so.
Since there are no source files that end with .dtb or .dtb.S, so we
can clean-up those files from the top-level Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Reintroduction of the EMAC bindings that were reverted in 4.13.
-----BEGIN PGP SIGNATURE-----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=mDKb
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.15-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner arm64 changes, take 2" from Maxime Ripard:
Reintroduction of the EMAC bindings that were reverted in 4.13.
* tag 'sunxi-dt64-for-4.15-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: add snps,dwmac-mdio compatible to emac/mdio
arm64: dts: allwinner: A64: Restore EMAC changes
Two long awaited changes:
- Reintroduction of the new EMAC DT bindings that got reverted at the
last minute in 4.13
- Introduction of the AXP803/813 PMIC support
-----BEGIN PGP SIGNATURE-----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=96rw
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.15-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner DT changes for 4.15, take 2" from Maxime Ripard:
Here are a few commits that would be great to get in 4.15, given how
long they've been hanging around.
The first and most important one is the reintroduction of the EMAC DT
changes after they've been reverted at the last minute in 4.13.
There's a arm64 patch that crept in because the H5 and H3 share a
common DTSI that is located in arch/arm, and merging that patch
through the arm64 PR, especially given the pull requests that have
already been sent, would just have generated too many conflicts.
* tag 'sunxi-dt-for-4.15-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
ARM: dts: sunxi: Restore EMAC changes (boards)
ARM: dts: sunxi: h3/h5: represent the mdio switch used by sun8i-h3-emac
arm: dts: sunxi: h3/h5: Restore EMAC changes
dt-bindings: net: dwmac-sun8i: update documentation about integrated PHY
dt-bindings: net: Restore sun8i dwmac binding
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.
This patch restore arm64 DT about dwmac-sun8i for H5
This reverts a part of commit 87e1f5e8bb ("arm64: dts: allwinner: Revert EMAC changes")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
stmmac bindings docs said that its mdio node must have
compatible = "snps,dwmac-mdio";
Since dwmac-sun8i does not have any good reasons to not doing it, all
their MDIO node must have it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.
This patch restore arm64 DT about dwmac-sun8i for A64
This reverts commit 87e1f5e8bb ("arm64: dts: allwinner: Revert EMAC changes")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Most notable changes:
- SPI and DMA support on the a64
- New boards: NanoPi NEO Plus2
-----BEGIN PGP SIGNATURE-----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=OAav
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner arm64 DT changes for 4.15" from Maxime Ripard:
Most notable changes:
- SPI and DMA support on the a64
- New boards: NanoPi NEO Plus2
* tag 'sunxi-dt64-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: allwinner: Correct unit name in devicetree binding example
arm64: allwinner: a64: add dma controller references to spi nodes
arm64: allwinner: a64: Add device node for DMA controller
arm64: allwinner: a64: Fix node with unit name and no reg property
arm64: allwinner: a64: Fix simple-bus unit address format error
arm64: allwinner: h5: add NanoPi NEO Plus2 DT support
arm64: allwinner: a64: add SPI nodes
The most notable changes are:
- Conversion to the last SoC (A10, A20) to the new clock framework
- HDMI and dual pipeline support for the A10, A20 and A31 DRM driver
- Support for the various power supplies on a number of boards
- Fix of DTC warnings on a number of SoCs, but most of them still need
some work
- New boards: A20-OLinuXino-MICRO-eMMC, TBS A711, Banana Pi M2 Berry,
Banana Pi M2 Ultra
-----BEGIN PGP SIGNATURE-----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=HjP6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner DT changes for 4.15" from Maxime Ripard:
The most notable changes are:
- Conversion to the last SoC (A10, A20) to the new clock framework
- HDMI and dual pipeline support for the A10, A20 and A31 DRM driver
- Support for the various power supplies on a number of boards
- Fix of DTC warnings on a number of SoCs, but most of them still need
some work
- New boards: A20-OLinuXino-MICRO-eMMC, TBS A711, Banana Pi M2 Berry,
Banana Pi M2 Ultra
- New R40 SoC support
* tag 'sunxi-dt-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (63 commits)
ARM: sun8i: r40: enable USB host for Banana Pi M2 Ultra
ARM: sun8i: v40: add 5V regulator for Banana Pi M2 Berry
ARM: sun8i: r40: add 5V regulator for Banana Pi M2 Ultra
ARM: sun8i: r40: add USB host port nodes for R40
ARM: dts: sun4i: Enable HDMI support on some A10 devices
ARM: dts: sun7i: Enable HDMI support on some A20 devices
ARM: dts: sun7i: Add device nodes for display pipelines
ARM: dts: sun4i: Add device nodes for display pipelines
ARM: dts: sun8i: r40: add watchdog device node
ARM: dts: sun5i: reference-design-tablet: Enable AXP209 AC and battery
ARM: dts: sun9i: Change node names to remove underscores
ARM: dts: sun9i: Change node names to remove underscores
ARM: dts: sun4i: Remove underscores from nodes names
ARM: dts: sun4i: Provide default muxing for relevant controllers
ARM: dts: sun4i: Change pinctrl nodes to avoid warning
ARM: dts: sun6i: Enable HDMI support on some A31/A31s devices
ARM: dts: sun6i: Add device node for HDMI controller
ARM: dts: sun4i: Change LRADC node names to avoid warnings
ARM: dts: sun4i: Remove skeleton and memory to avoid warnings
ARM: dts: sun4i: Remove gpio-keys warnings
...
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm64/boot/dts -type -f -name '*.dts*'
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The spi controller nodes omit the dma controller/channel references, add
it.
This does not yet enable DMA for SPI transfers, as the spi-sun6i driver
lacks support for DMA, but always uses PIO to the FIFO.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A64 SoC has a DMA controller that supports 8 DMA channels
to and from various peripherals. The last used DRQ port is 27.
Add a device node for it.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch fix the warning "xxx has a unit name, but no reg property" by
removing "@0" from such node
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This patch remove leading 0 of unit address and so remove
lots of warning when building DT with W=1.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The A64 SPI controllers are register compatible to the h3/h5 SPI
controllers.
The A64 has two SPI controllers, each with a single chip select.
The handles for the DMA channels (23/24 for SPI0/SPI1) are omitted,
as the A64 DMA support is currently missing.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since current tree support AXP803 regulators, replace
fixed regulator with AXP803 dcdc1 regulator.
Tested on pine64.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
-----BEGIN PGP SIGNATURE-----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=0xy6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64
Allwinner fixes for 4.13, take 3
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
* tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: dts: sunxi: Revert EMAC changes
arm64: dts: allwinner: Revert EMAC changes
dt-bindings: net: Revert sun8i dwmac binding
arm64: allwinner: h5: fix pinctrl IRQs
arm64: allwinner: a64: sopine: add missing ethernet0 alias
arm64: allwinner: a64: pine64: add missing ethernet0 alias
arm64: allwinner: a64: bananapi-m64: add missing ethernet0 alias
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
Since the discussion is not settled yet for the EMAC, and that the release
in getting really close, let's revert the changes for now, and we'll
reintroduce them later.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The usual improvement patches:
- PMIC, USB and WiFi enabled for Bananapi M64
- New board added: NanoPi A64
- New board added: Olimex A64-OLinuXino
-----BEGIN PGP SIGNATURE-----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=u/18
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.14-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64
Pull "Allwinner arm64 device tree changes for 4.14, round 2" from Chen-Yu Tsai:
The usual improvement patches:
- PMIC, USB and WiFi enabled for Bananapi M64
- New board added: NanoPi A64
- New board added: Olimex A64-OLinuXino
* tag 'sunxi-dt64-for-4.14-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: a64: Add A64-OLinuXino initial support
arm64: allwinner: a64: Add initial NanoPi A64 support
arm64: allwinner: a64: add proper support for the Wi-Fi on BPi M64
arm64: allwinner: a64: enable AXP803 for Banana Pi M64
arm64: allwinner: a64: enable USB host controller for BPi M64
The usual improvement patches:
- R_INTC interrupt controller enabled for the A64 SoC
- AXP803 PMIC added and enabled on the Pine64 and SoPine boards
-----BEGIN PGP SIGNATURE-----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=9oen
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64
Pull "Allwinner arm64 DT changes for 4.14" from Chen-Yu Tsai:
The usual improvement patches:
- R_INTC interrupt controller enabled for the A64 SoC
- AXP803 PMIC added and enabled on the Pine64 and SoPine boards
* tag 'sunxi-dt64-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: a64: add AXP803 PMIC support to SoPine and the baseboard
arm64: allwinner: a64: enable AXP803 regulators for Pine64
arm64: allwinner: a64: add DTSI file for AXP803 PMIC
arm64: allwinner: a64: add AXP803 node to Pine64 device tree
arm64: allwinner: a64: add NMI (R_INTC) controller on A64
NanoPi A64 is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner A64 SOC.
Nanopi A64 features
- Allwinner A64, 64-bit Quad-core Cortex-A53@648MHz to 1.152GHz, DVFS
- 1GB DDR3 RAM
- MicroSD
- Gigabit Ethernet (RTL8211E)
- Wi-Fi 802.11b/g/n
- IR receiver
- Audio In/Out
- Video In/Out
- Serial Debug Port
- microUSB 5V 2A DC power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The pin controller of H5 has three IRQs at the chip's GIC, which
represents three banks of pinctrl IRQs. However, the device tree used to
miss the third IRQ of the pin controller, which makes the PG bank IRQ
not usable.
Add the missing IRQ to the pinctrl node.
Fixes: 4e36de179f ("arm64: allwinner: h5: add Allwinner H5 .dtsi")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
BPi M64 has an AP6212 Wi-Fi/Bluetooth combo module, and the Wi-Fi SDIO
card is connected to the mmc1 controller.
The pwrseq of the mmc1 (used to reset the card) used to missing, and the
out-of-band interrupt line of the card is not specified.
Fix these issues for proper Wi-Fi support of BPi M64.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Banana Pi M64 board uses an AXP803 PMIC.
Enable the PMIC and its regulators.
As we have now proper regulators support, missing or dummy regulators
are changed to the correct ones.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Banana Pi M64 connects the USB host-only controller on A64 SoC to a USB
hub, which provided the two USB Type-A ports on the board.
Enable the USB host controller.
The OTG function of the Micro-USB port needs the drivevbus function of
the AXP803 driver implemented, so it's not enabled now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The EMAC Ethernet controller was enabled, but an accompanying alias
was not added. This results in unstable numbering if other Ethernet
devices, such as a USB dongle, are present. Also, the bootloader uses
the alias to assign a generated stable MAC address to the device node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixes: 96219b0048 ("arm64: allwinner: a64: add device tree for SoPine
with baseboard")
[wens@csie.org: Rewrite commit log as fixing a previous patch with Fixes]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The EMAC Ethernet controller was enabled, but an accompanying alias
was not added. This results in unstable numbering if other Ethernet
devices, such as a USB dongle, are present. Also, the bootloader uses
the alias to assign a generated stable MAC address to the device node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixes: 9702394374 ("arm64: allwinner: pine64: Enable dwmac-sun8i")
[wens@csie.org: Rewrite commit log as fixing a previous patch with Fixes]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The EMAC Ethernet controller was enabled, but an accompanying alias
was not added. This results in unstable numbering if other Ethernet
devices, such as a USB dongle, are present. Also, the bootloader uses
the alias to assign a generated stable MAC address to the device node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixes: e729549990 ("arm64: allwinner: bananapi-m64: Enable dwmac-sun8i")
[wens@csie.org: Rewrite commit log as fixing a previous patch with Fixes]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The datasheet said that emac register size is 0x10000 not 0x100
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Fixed commit subject prefix]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The SoPine SoM has an AXP803 PMIC connected to the RSB bus of the A64
SoC, and the regulators of the PMIC are used both on the SoM itself and
on the official baseboard
Add related device tree parts to the SoPine SoM DTSI file and the
baseboard DT.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add support of AXP803 regulators in the Pine64 device tree.
The phy-supply regulator is also set in EMAC device node, in order to
prevent Ethernet regression by regulator get disabled by regulator
framework.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As nearly all A64 boards are using AXP803 PMIC, add a DTSI file for it,
like the old DTSI files for AXP20x/22x, for the common parts of the
PMIC.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Pine64 (including Pine64+) boards have an AXP803 as its main PMIC.
Add its device node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Allwinner A64 SoC features a R_INTC controller, which controls the NMI
line, and this interrupt line is usually connected to the AXP PMIC.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[wens@csie.org: Add fallback sun6i-a31-r-intc compatible]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Device-tree updates for arm64 platforms. For the first time I can
remember, this is actually larger than the corresponding branch for
32-bit platforms overall, though that has more individual changes.
A significant portion this time is due to added machine support:
- Initial support for the Realtek RTD1295 SoC, along with the Zidoo
X9S set-top-box
- Initial support for Actions Semi S900 and the Bubblegum-96
single-board-cёmputer.
- Rockchips support for the rk3399-Firefly single-board-computer
gets added, this one stands out for being relatively fast,
affordable and well₋supported, compared to many boards that
only fall into one or two of the above categories.
- Mediatek gains support for the mt6797 mobile-phone SoC platform
and corresponding evaluation board.
- Amlogic board support gets added for the NanoPi K2 and S905x
LibreTech CC single-board computers and the R-Box Pro set-top-box
- Allwinner board support gets added for the OrangePi Win,
Orangepi Zero Plus 2, NanoPi NEO2 and Orange Pi Prime single
board computers and the SoPine system-on-module.
- Renesas board support for Salvator-XS and H3ULCB
automotive development systems.
- Socionext Uniphier board support for LD11-global and LD20-global,
whatever those may be.
- Broadcom adds support for the new Stingray communication processor
in its iProc family, along with two reference boards.
Other updates include:
- For the hisicon platform, support for Hi3660-Hikey960 gets
extended significantly.
- Lots of smaller updates for Renesas, Amlogic, Rockchip, UniPhier,
Broadcom, Allwinner, Hisilicon, Qualcomm, Marvell, and NXP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=E8pa
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"Device-tree updates for arm64 platforms. For the first time I can
remember, this is actually larger than the corresponding branch for
32-bit platforms overall, though that has more individual changes.
A significant portion this time is due to added machine support:
- Initial support for the Realtek RTD1295 SoC, along with the Zidoo
X9S set-top-box
- Initial support for Actions Semi S900 and the Bubblegum-96
single-board-cёmputer.
- Rockchips support for the rk3399-Firefly single-board-computer gets
added, this one stands out for being relatively fast, affordable
and well₋supported, compared to many boards that only fall into one
or two of the above categories.
- Mediatek gains support for the mt6797 mobile-phone SoC platform and
corresponding evaluation board.
- Amlogic board support gets added for the NanoPi K2 and S905x
LibreTech CC single-board computers and the R-Box Pro set-top-box
- Allwinner board support gets added for the OrangePi Win, Orangepi
Zero Plus 2, NanoPi NEO2 and Orange Pi Prime single board computers
and the SoPine system-on-module.
- Renesas board support for Salvator-XS and H3ULCB automotive
development systems.
- Socionext Uniphier board support for LD11-global and LD20-global,
whatever those may be.
- Broadcom adds support for the new Stingray communication processor
in its iProc family, along with two reference boards.
Other updates include:
- For the hisicon platform, support for Hi3660-Hikey960 gets extended
significantly.
- Lots of smaller updates for Renesas, Amlogic, Rockchip, UniPhier,
Broadcom, Allwinner, Hisilicon, Qualcomm, Marvell, and NXP"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (243 commits)
ARM64: dts: marvell: armada37xx: Fix timer interrupt specifiers
Revert "arm64: dts: marvell: add dma-mask in crypto nodes for 7k/8k"
arm64: dts: mediatek: don't include missing file
ARM64: dts: meson-gxl: Add Libre Technology CC support
dt-bindings: arm: amlogic: Add Libre Technology CC board
dt-bindings: add Libre Technology vendor prefix
arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K
arm64: dts: zte: Use - instead of @ for DT OPP entries
arm64: dts: marvell: add gpio support for Armada 7K/8K
arm64: dts: marvell: add pinctrl support for Armada 7K/8K
arm64: dts: marvell: use new binding for the system controller on cp110
arm64: dts: marvell: remove *-clock-output-names on cp110
arm64: dts: marvell: use new bindings for xor clocks on ap806
arm64: dts: marvell: mcbin: enable the mdio node
arm64: dts: Add Actions Semi S900 and Bubblegum-96
dt-bindings: Add vendor prefix for uCRobotics
arm64: dts: marvell: add xmdio nodes for 7k/8k
arm64: dts: marvell: add a comment on the cp110 slave node status
arm64: dts: marvell: remove cpm crypto nodes from dts files
arm64: dts: marvell: cp110: enable the crypto engine at the SoC level
...
Just like the H3, this is mostly about enabling the EMAC on the H5, and
also has a new board, the Orange Pi Zero Plus 2
-----BEGIN PGP SIGNATURE-----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=x40b
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-h5-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64
Allwinner H5 DT changes for 4.13
Just like the H3, this is mostly about enabling the EMAC on the H5, and
also has a new board, the Orange Pi Zero Plus 2
* tag 'sunxi-dt-h5-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: h5: Add initial Orangepi Zero Plus 2 support
arm64: allwinner: h5: enable dwmac-sun8i for Nano Pi NEO2
arm64: allwinner: h5: enable dwmac-sun8i for Orange Pi Prime
arm64: allwinner: h5: sort the device nodes in / part for some boards
arm64: allwinner: h5: add support for NanoPi NEO2 board
arm64: allwinner: h5: add support for Orange Pi Prime board
arm64: allwinner: orangepi-pc2: Enable dwmac-sun8i
arm: sun8i: sunxi-h3-h5: add dwmac-sun8i ethernet driver
arm: sun8i: sunxi-h3-h5: Add dt node for the syscon control module
ARM: sunxi: h3-h5: Convert R_CCU raw numbers to macros
Signed-off-by: Olof Johansson <olof@lixom.net>
Orangepi Zero Plus 2 is an open-source single-board computer
using the Allwinner h5 SOC.
H5 Orangepi Zero Plus 2 has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG+power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Orangepi Win/WinPlus is an open-source single-board computer
using the Allwinner A64 SOC.
A64 Orangepi Win/WinPlus has
- A64 Quad-core Cortex-A53 64bit
- 1GB(Win)/2GB(Win Plus) DDR3 SDRAM
- Debug TTL UART
- Four USB 2.0
- HDMI
- LCD
- Audio and MIC
- Wifi + BT
- IR receiver
- 5V DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the required DT parts to enable Ethernet (dwmac-sun8i driver) on
the Nano Pi NEO2 board. It uses an external Realtek RTL8211E PHY
connected via RGMII to provide GbE network. Specially unlike other
Allwinner boards, the phy is connected to MDIO address 7, not 1.
This includes the regulator (which is controlled by a GPIO pin) and
the actual Ethernet MAC node, referring the RGMII pins of the device.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the required DT parts to enable Ethernet (dwmac-sun8i driver) on
the Orange Pi Prime board. It uses an external Realtek RTL8211E PHY
connected via RGMII to provide GbE network.
This includes the regulator (which is controlled by a GPIO pin) and
the actual Ethernet MAC node, referring the RGMII pins of the device.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The reg_vcc3v3 node is wrongly placed at the start of the / part, but
not with other fixed regulators used by the board, which makes the
device nodes unsorted.
As Orange Pi Prime and Nano Pi NEO2 device trees are copy'n'paste works,
they share the device node unsorted issue.
Fix this by move reg_vcc3v3 node to the position before reg_usb0_vbus.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pine64 have made an official baseboard when SoPine SoM is out.
The official baseboard is like the original Pine64 -- but with SD card
slot replaced with Pine64's eMMC module slot.
Add a device tree for SoPine with the baseboard.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the BananaPi M64.
It uses an external PHY rtl8211e via RGMII.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the pine64 plus.
It uses an external PHY rtl8211e via RGMII.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the pine64
It uses an external PHY via RMII.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i is an Ethernet MAC that supports 10/100/1000 Mbit
connections. It is very similar to the device found in the Allwinner
H3, but lacks the internal 100 Mbit PHY and its associated control
bits.
This adds the necessary bits to the Allwinner A64 SoC .dtsi, but keeps
it disabled at this level.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch add the dt node for the syscon register present on the
Allwinner A64.
Only two register are present in this syscon and the only one useful is
the one dedicated to EMAC clock.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
SoPine is a SoM by Pine64, which have a gold finger compatible with the
slot of DDR3 SODIMM (signals are not compatible), and have an A64, an
AXP803, a LPDDR3 DRAM chip, a power led and a MicroSD slot on it.
The card detect pin of the MicroSD slot on the SoM is pulled down, which
makes it unusable; however, the slot is at the surface of the SoM that
is closed to the baseboard, so it's nearly impossible to hot-swap it,
thus I make it non-removable.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A64 device tree file has some remnants of raw number references
to the CCU node, likely from when the CCU bindings and device tree
changes were first merged.
Convert these, and the R_CCU ones, to use the proper defined macros
from their respective device tree binding header files.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pine64 exposes all A64 UARTs, not just UART0.
Since the pins can be used as GPIO, don't enable the new UART nodes by
default, but prepare the pinctrl settings to aid in activating them via
overlays, i.e., overriding the status property of &uartX nodes.
For UART4 (Euler) the safer route of not including RTS/CTS pins is chosen,
whereas for UART1 (Bluetooth) they are included.
Add the corresponding pinctrl nodes where missing.
Suggested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A64 have a RSB controller like the one on A23/A33 SoCs.
Add it and its pinmux.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enabling uart2 node currently leads to a /dev/ttyS1 device, with ttyS0..4
always present, causing confusion on the user's part.
dtc cannot resolve an overlay's &uart2 reference for strings, only for
phandles, so it would need to hardcode the full node path.
Avoid this and enforce reliable numbering by adding serialX aliases for:
UART1 - on Wifi/BT connector
UART2 - on Pi-2 connector
UART3 - on Euler connector
UART4 - on Euler connector
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
UART2 is exposed on the Pi connector of Pine64. Make a pinctrl node
available at the SoC level, to simplify enabling UART2 via DT overlay.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
NanoPi NEO2 is a board with the same size factor with the original
NanoPi NEO by FriendlyELEC.
It has a H5 instead of H3 on NanoPi NEO, and the ethernet is upgraded to
1Gbps (with external RTL8211E PHY).
Add support for this board.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Orange Pi Prime is a new Allwinner H5-based SBC by Xunlong.
It's like a Orange Pi Plus 2E with H3 replaced with H5, eMMC replaced
with onboard SPI NOR Flash and wireless card changed to Realtek
RTL8723BS (with Bluetooth functionality).
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the Orange PI PC2.
It uses an external PHY rtl8211e via RGMII.
This patch create the needed regulator, emac and phy nodes.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AR100 clock within the R_CCU (PRCM) has the PLL_PERIPH0 as one of
its parents.
This adds the reference in the device tree describing this relationship.
This patch uses a raw number for the clock index to ease merging by
avoiding cross tree dependencies.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The arm64 H5 and arm H3 SoCs share roughly the same base, and therefore
share a significant part of their device tree.
The approach we took was to add a symlink from the arm64 DTSI to the arm
DTSI.
Now that the arm DT folder is exposed in the include path, we can just use
it and remove our symlink.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As we have USB0 controller switch available on A64, we should now enable
the EHCI0/OHCI0 controllers for Pine64.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A64 SoC features a pair of EHCI/OHCI controllers that can be
set to wire to USB0 port (the OTG-capable one), which can be used to
provide a better performance in host mode.
Add their device tree nodes.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch of smaller
changes, but also some new platforms that are worth mentioning:
* Rockchip RK3399 platforms for Chromebooks, including Samsung Chromebook
Plus (Kevin)
* Orange Pi PC2 (Allwinner H5)
* Freescale LS2088A and LS1088A SoCs
* Expanded support for Nvidia Tegra186 (and Jetson TX2)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=q3Ix
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Olof Johansson:
"Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch
of smaller changes, but also some new platforms that are worth
mentioning:
- Rockchip RK3399 platforms for Chromebooks, including Samsung
Chromebook Plus (Kevin)
- Orange Pi PC2 (Allwinner H5)
- Freescale LS2088A and LS1088A SoCs
- Expanded support for Nvidia Tegra186 (and Jetson TX2)"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (180 commits)
arm64: dts: Add basic DT to support Spreadtrum's SP9860G
arm64: dts: exynos: Use - instead of @ for DT OPP entries
arm64: dts: exynos: Add support for s6e3hf2 panel device on TM2e board
arm64: dts: juno: add information about L1 and L2 caches
arm64: dts: juno: fix few unit address format warnings
arm64: marvell: dts: enable the crypto engine on the Armada 8040 DB
arm64: marvell: dts: enable the crypto engine on the Armada 7040 DB
arm64: marvell: dts: add crypto engine description for 7k/8k
arm64: dts: marvell: add sdhci support for Armada 7K/8K
arm64: dts: marvell: add eMMC support for Armada 37xx
arm64: dts: hisi: add pinctrl dtsi file for HiKey960 development board
arm64: dts: hisi: add drive strength levels of the pins for Hi3660 SoC
arm64: dts: hisi: enable the NIC and SAS for the hip07-d05 board
arm64: dts: hisi: add SAS nodes for the hip07 SoC
arm64: dts: hisi: add RoCE nodes for the hip07 SoC
arm64: dts: hisi: add network related nodes for the hip07 SoC
arm64: dts: hisi: add mbigen nodes for the hip07 SoC
arm64: dts: rockchip: fix the memory size of PX5 Evaluation board
arm64: dts: hisilicon: add dts files for hi3798cv200-poplar board
dt-bindings: arm: hisilicon: add bindings for hi3798cv200 SoC and Poplar board
...
H5 patches for 4.12, which are mostly related to reworking the H3 DTSI to
be usable on the arm64 H5 DTSI, that shares almost everything with the H3
but the CPU cores.
We then have patches to support the H5 boards on top.
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJY5guIAAoJEBx+YmzsjxAgCOAP/izjrX7AD/lxwAQ1BtfIuNcK
rSpQ4TjF7hO1r0pN1XoIs538U5uYWiBPhpoL+bxu9cdv33i1jojM6MFMAGfyWES4
bjEHU/dI6zBGeJ/icwSEjP1Wl6N+h6eZwzJ01VQsdc91RZXXqgT2xCVXGIJDtuTw
H/+iwvpF6ZqyTFXzhhx8YH7Aqn0X9+nuy6WALyr7d4awa7uLw0QL54Lr3gJWaGvm
Si/o8SjZU6pLF3KyDlcOwlDem+YD6ghH+eZXa1323xoctPQRuFZTiinnolhxJWFc
w+yhK6PtfR8CJ/WlfEEtMjjYQxeefr6MCQjaPjrY67YwE61PlcOZADAB77DujZ/2
Na47Olqp7vJ1yg19X5W/GlxfWa9P0H0VuRE8ZPMfZXGIHFBTgjHuE+pGds38IDvd
Zr0z/fX9WjTUDK9qFD9JHDL9FAJo7gjNGMMMiUvEjR8xpTJhhmAeAzpgZj+Aa78f
ZOYzu8J1xYf2yT/Xj/lDz7FHcWJEc89go9fX+lc8ILaFcXYvokqjfGnD6+ODf0FW
sO54p1OhjEt8yIEnH2js9C+YCIsuMeZ6e6fHjfp/uVVLPb94fhXKSQGYKRmXPJkK
gEdd2OS+I+diM0BAd2mKRlr57mEoPtkl07yx2E2eqCjIG/8wBN0C76KM9p0yPWof
YAaV+iAHOdsvT43alrXp
=ilmt
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-h5-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64
Allwinner H5 DT changes for 4.12
H5 patches for 4.12, which are mostly related to reworking the H3 DTSI to
be usable on the arm64 H5 DTSI, that shares almost everything with the H3
but the CPU cores.
We then have patches to support the H5 boards on top.
* tag 'sunxi-dt-h5-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: sunxi: h3/h5: switch apb0-related clocks to r_ccu
arm64: allwinner: h5: enable USB OTG on Orange Pi PC 2 board
arm64: allwinner: h5: add support for the Orange Pi PC 2 board
arm64: allwinner: h5: add Allwinner H5 .dtsi
ARM: sunxi: h3/h5: add usb_otg and OHCI/EHCI for usbc0 on H3/H5
arm: sun8i: h3: split Allwinner H3 .dtsi
arm: sun8i: h3: correct the GIC compatible in H3 to gic-400
arm: sun8i: h3: drop pinctrl-a10.h inclusion for H3 DTSI
arm: sun8i: h3: drop skeleton.dtsi inclusion in H3 DTSI
Signed-off-by: Olof Johansson <olof@lixom.net>
The USB PHY in A64 has a "pmu0" region, which controls the EHCI/OHCI
controller pair that can be connected to the PHY0.
Add the MMIO region for PHY node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A64 have a dedicated pin controller to manage the PL pin bank.
As the driver and the required clock support are added, add the device
node for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A64 SoC have a CCU (r_ccu) in PRCM block.
Add the device node for it.
The mux 3 of R_CCU is an internal oscillator, which is 16MHz according
to the user manual, and has only 30% accuracy based on our experience
on older SoCs. The real mesaured value of it on two Pine64 boards is
around 11MHz, which is around 70% of 16MHz.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Orange Pi PC 2 board features a OTG port like the one on older H3 Orange
Pi's, with PG12 pin being the id det pin and PL2 being the vbus driver
pin.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orange Pi PC 2 is a typical single board computer using the
Allwinner H5 SoC. Apart from the usual suspects it features three
separately driven USB ports and a Gigabit Ethernet port.
Also it has a SPI NOR flash soldered, from which the board can boot
from. This enables the SBC to behave like a "real computer" with
built-in firmware.
Add the board specific .dts file, which includes the H5 .dtsi and
enables the peripherals that we support so far.
Reviewed-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio,
change MMC cd to active-low, rename some node names to prevent
underscores]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
Cortex-A53 cores instead.
Based on the now shared base .dtsi describing the common peripherals
describe the H5 specific nodes on top of that.
That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
refactor, commit message changed to meet new arm64 naming scheme,
drop H3 pinctrl compatible because of interrupt bank change, drop
H3 ccu compatible because of clock change, drop ccu node as it come
into h3-h5 dtsi]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Banana Pi M64 board is a typical single board computer based on the
Allwinner A64 SoC. Aside from the usual peripherals it features eMMC
storage, which is connected to the 8-bit capable SDHC2 controller.
Also it has a soldered WiFi/Bluetooth chip, so we enable UART1 and SDHC1
as those two interfaces are connected to it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
On many boards UART1 connects to a Bluetooth chip, so add the pinctrl
nodes for the only pins providing access to that UART. That includes
those pins for hardware flow control (RTS/CTS).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
All Pine64 boards connect an micro-SD card slot to the first MMC
controller.
Enable the respective DT node and specify the (always-on) regulator
and card-detect pin.
As a micro-SD slot does not feature a write-protect switch, we disable
this feature.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The eMMC controller seem to have a maximum frequency of 200MHz, while the
regular MMC controllers are capped at 150MHz.
Since older SoCs cannot go that high, we cannot change the default maximum
frequency, but fortunately for us we have a property for that in the DT.
This also has the side effect of allowing to use the MMC HS200 and SD
SDR104 modes for the boards that support it (with either 1.2v or 1.8v IOs).
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A64 only has a single set of pins for each MMC controller. Since we
already have boards that require all of them, let's add them to the DTSI.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A64 has 3 MMC controllers, one of them being especially targeted to
eMMC. Among other things, it has a data strobe signal and a 8 bits data
width.
The two other are more usual controllers that will have a 4 bits width at
most and no data strobe signal, which limits it to more usual SD or MMC
peripherals.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
All dts files for the sunxi platform have been switched to the generic
pinconf bindings. As a result, the sunxi specific pinctrl macros are
no longer used.
Remove the #include entry with the following command:
sed -i -e '/pinctrl\/sun4i-a10.h/D' \
arch/arm64/boot/dts/allwinner/*.dts?
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A64 has a MUSB controller wired to the USB PHY 0, which is connected
to the upper USB Type-A port of Pine64.
As the port is a Type-A female port, enable it in host-only mode in the
device tree, which makes devices with USB Type-A male port can work on
this port (which is originally designed by Pine64 team).
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A64 SoC has a MUSB controller like the one in A33, so add
a node for it, just use the compatible of A33 MUSB.
Host mode is tested to work properly on Pine64 and will be added into
the device tree of Pine64 in next patch.
Peripheral mode is also tested on Pine64, by changing dr_mode property
of usb_otg node and use a non-standard USB Type-A to Type-A cable.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pine64 have two USB Type-A ports, which are wired to the two ports of
A64 USB PHY, and the lower port is the EHCI/OHCI1 port.
Enable the necessary nodes to enable the lower USB port to work.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In this dts file, uart0 node is put before i2c1.
Move the uart0 node to the end to satisfy alphebetical order.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A64 have two HCI USB controllers, a OTG controller and a USB
PHY device which have two ports. One of the port is wired to both a HCI
USB controller and the OTG controller, which is currently not supported.
The another one is only wired to a HCI controller, and the device node of
OHCI/EHCI controller of the port can be added now.
Also the A64 USB PHY device node is also added for the HCI controllers to
work.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Two branches were incorrectly sent without having the necessary
header file changes. Rather than back those out now, I'm replacing
the symbolic names for the clks and resets with the numeric
values to get 'make allmodconfig dtbs' back to work.
After the header file changes are merged, we can revert this
patch.
Fixes: 6bc37fa ("arm64: dts: add Allwinner A64 SoC .dtsi")
Fixes: 50784e6 ("dts: arm64: db820c: add pmic pins specific dts file")
Acked-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Pine64 is a cost-efficient development board based on the
Allwinner A64 SoC.
There are three models: the basic version with Fast Ethernet and
512 MB of DRAM (Pine64) and two Pine64+ versions, which both
feature Gigabit Ethernet and additional connectors for touchscreens
and a camera. Or as my son put it: "Those are smaller and these are
missing." ;-)
The two Pine64+ models just differ in the amount of DRAM
(1GB vs. 2GB). Since U-Boot will figure out the right size for us and
patches the DT accordingly we just need to provide one DT for the
Pine64+.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Maxime: Removed the common DTSI and include directly the pine64 DTS]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A64 SoC is a low-cost chip with 4 ARM Cortex-A53 cores
and the typical tablet / TV box peripherals.
The SoC is based on the (32-bit) Allwinner H3 chip, sharing most of
the peripherals and the memory map.
Although the cores are proper 64-bit ones, the whole SoC is actually
limited to 4GB (including all the supported DRAM), so we use 32-bit
address and size cells. This has the nice feature of us being able to
reuse the DT for 32-bit kernels as well.
This .dtsi lists the hardware that we support so far.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
[Maxime: Convert to CCU binding, drop the MMC support for now]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
