Adding disable-wp property for micro SD nodes of Allwinner arm64 devices.
Boards were verified from online pictures/tables
that they have micro SD slots.
Signed-off-by: Kryštof Černý <cleverline1mc@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://patch.msgid.link/20240919-b4-nanopineoplus2-fix-mmc0-wp-v2-1-c708a9abc9eb@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Now that the H616 (and variants) audio codec is supported, enable it for
boards with a mainline DTS. The Tanix TX1, Transpeed 8K618-T and X-96
Mate have all been tested with the onboard 3.5mm audio jack and the
Orange Pi Zero 3 with a 3.5mm jack connected to the audio header.
The RG35XX (2024, -H, -Plus and -SP variants) are also tested working
but have a separate mux and GPIO-controlled (PI5) power amplifier to
support both a headphone jack and onboard speakers.
The headphone jack has a GPIO for jack detection, but this is not
currently supported by the driver, so audio is heard both via the
headphone jack and speakers when the speaker amp is powered (by the
CLDO1 regulator, defined as always-on until proper jack detection is
implemented).
Define the audio codec and routing for all supported H616 and variant
boards, and power and speaker amp enablement where present on boards and
known.
Signed-off-by: Ryan Walklin <ryan@testtoast.com>
Tested-by: Philippe Simons <simons.philippe@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Link: https://patch.msgid.link/20241023075917.186835-8-ryan@testtoast.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Now that the sun4i codec driver supports the H616, add a node in the
device tree for it (correcting the spdif block location at the same
time).
Signed-off-by: Ryan Walklin <ryan@testtoast.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://patch.msgid.link/20241023075917.186835-7-ryan@testtoast.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Pin controllers pio and r_pio will have proper regulators assigned.
Signed-off-by: Kryštof Černý <cleverline1mc@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20240905-nanopi-neo-plus2-regfix-v3-2-1895dff59598@gmail.com
[wens@csie.org: Make "h5" lowercase to match most commits]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Added the main board 5 V supply regulator,
a 2.5 V supply regulator for GMAC PHY IO and correct vin-supply elements.
Signed-off-by: Kryštof Černý <cleverline1mc@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20240905-nanopi-neo-plus2-regfix-v3-1-1895dff59598@gmail.com
[wens@csie.org: Make "h5" lowercase to match most commits]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add thermal trips for the two GPU thermal sensors found in the Allwinner A64.
There's only one GPU OPP defined since the commit 1428f0c19f ("arm64: dts:
allwinner: a64: Run GPU at 432 MHz"), so defining only the critical thermal
trips makes sense for the A64's two GPU thermal zones.
Having these critical thermal trips defined ensures that no hot spots develop
inside the SoC die that exceed the maximum junction temperature. That might
have been possible before, although quite unlikely, because the CPU and GPU
portions of the SoC are packed closely inside the SoC, so the overheating GPU
would inevitably result in the heat soaking into the CPU portion of the SoC,
causing the CPU thermal sensor to return high readings and trigger the CPU
critical thermal trips. However, it's better not to rely on the heat soak
and have the critical GPU thermal trips properly defined instead.
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Tested-by: Norayr Chilingarian <norayr@arnet.am>
Link: https://lore.kernel.org/r/0a6110a7b27a050bd58ab3663087eecd8e873ac0.1724126053.git.dsimic@manjaro.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Anbernic RG35XXSP is almost identical to the RG35XX-Plus, but in a
clamshell form-factor. The key differences between the SP and the Plus
is a lid switch and an RTC on the same i2c bus as the PMIC.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20240710231718.106894-5-macroalpha82@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Change the Anbernic RG35XX series to use the r_i2c bus for the PMIC
instead of the r_rsb bus. This is to keep the device tree consistent
as there are at least 3 devices (the RG35XX-SP, RG28XX, and RG40XX-H)
that have an external RTC on the r_i2c bus.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Ryan Walklin <ryan@testtoast.com>
Link: https://lore.kernel.org/r/20240710231718.106894-4-macroalpha82@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add pinctrl nodes for the r_i2c node. Without the pinmux defined the
r_i2c bus may fail to work, possibly if the bootloader uses rsb mode
for the PMIC.
Fixes: 0d17c86511 ("arm64: dts: allwinner: Add Allwinner H616 .dtsi file")
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Fixes: 0d17c86511 ("arm64: dts: allwinner: Add Allwinner H616 .dtsi file")
Link: https://lore.kernel.org/r/20240710231718.106894-3-macroalpha82@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The devicetree updates are fairly well spread out across platforms,
with Qualcomm making up about a third of the total.
There are three new SoCs in existing product families this:
- NXP i.MX95 is a variant of i.MX93, now with six Cortex-A55 cores
instead of just two as well as a GPU and more high-speed I/O
devices.
- Qualcomm QCS8550 is a variant of SM8550 for IOT devices
- Airoha EN7581 is a 10G-PON network chip and related to
the MT7981 Wireless router chip from its parent Mediatek.
In total there are 58 new machines, including four riscv
boards and eight for 32-bit arm.
The most exciting new addition is probably a pair of laptops
based on the Qualcomm x1e80100 (Snapdragon X1 Elite) chip,
the Asus Vivobook S15 and the Lenovo Yoga Slim7x.
Other noteworthy new additions are:
- A total of 20 Qualcomm based machines, mostly Android devices
from Samsung, Motorola and LG, as well as a wireless router
and some reference designs
- Six NXP i.MX based machines, mostly industrial boards along
with some reference designs
- Mediatek sees some interesting Filogic based routers
including the "OpenWRT One", a few new Chromebooks as
well as single-board computers.
- Four machines from Solidrun based on Marvell cn913x,
replacing the older Armada 8000 based counterparts
- The four Amlogic machines are all set top boxes or reference
designs for them
- The nine new Rockchips machines are mostly single-board
computers including some interesting ones based on the
rk3588 chip like the ROCK 5 ITX board and the CM3588
with its four NVMe slots
- The RISC-V boards are all single-board computers based on
Starfive JH7110, Microchip MPFS and Allwinner D1, which all
had similar boards already
There are also a lot of updates to already supported machines,
notably for the TI K3, Rockchips, Freescale and of course
Qualcomm platforms.
-----BEGIN PGP SIGNATURE-----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=xGqj
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC dt updates from Arnd Bergmann:
"The devicetree updates are fairly well spread out across platforms,
with Qualcomm making up about a third of the total.
There are three new SoCs in existing product families this:
- NXP i.MX95 is a variant of i.MX93, now with six Cortex-A55 cores
instead of just two as well as a GPU and more high-speed I/O
devices.
- Qualcomm QCS8550 is a variant of SM8550 for IOT devices
- Airoha EN7581 is a 10G-PON network chip and related to the MT7981
Wireless router chip from its parent Mediatek.
In total there are 58 new machines, including four riscv boards and
eight for 32-bit arm.
The most exciting new addition is probably a pair of laptops based on
the Qualcomm x1e80100 (Snapdragon X1 Elite) chip, the Asus Vivobook
S15 and the Lenovo Yoga Slim7x.
Other noteworthy new additions are:
- A total of 20 Qualcomm based machines, mostly Android devices from
Samsung, Motorola and LG, as well as a wireless router and some
reference designs
- Six NXP i.MX based machines, mostly industrial boards along with
some reference designs
- Mediatek sees some interesting Filogic based routers including the
"OpenWRT One", a few new Chromebooks as well as single-board
computers.
- Four machines from Solidrun based on Marvell cn913x, replacing the
older Armada 8000 based counterparts
- The four Amlogic machines are all set top boxes or reference
designs for them
- The nine new Rockchips machines are mostly single-board computers
including some interesting ones based on the rk3588 chip like the
ROCK 5 ITX board and the CM3588 with its four NVMe slots
- The RISC-V boards are all single-board computers based on Starfive
JH7110, Microchip MPFS and Allwinner D1, which all had similar
boards already
There are also a lot of updates to already supported machines, notably
for the TI K3, Rockchips, Freescale and of course Qualcomm platforms"
* tag 'soc-dt-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (846 commits)
arm64: dts: allwinner: h616: add crypto engine node
riscv: dts: add clock generator for Sophgo SG2042 SoC
arm64: dts: rockchip: Add Xunlong Orange Pi 3B
dt-bindings: arm: rockchip: Add Xunlong Orange Pi 3B
arm64: dts: rockchip: Add Radxa ROCK 3B
dt-bindings: arm: rockchip: Add Radxa ROCK 3B
mailmap: Update Luca Weiss's email address
ARM: dts: ixp4xx: nslu2: beeper uses PWM
arm64: dts: rockchip: add ROCK 5 ITX board
dt-bindings: arm: rockchip: Add ROCK 5 ITX board
arm64: dts: rockchip: Add dma-names to uart1 on Pine64 rk3566 devices
arm64: dts: rockchip: Add avdd supplies to hdmi on rock64
arm64: dts: qcom: msm8916-lg-c50: add initial dts for LG Leon LTE
arm64: dts: qcom: msm8916-lg-m216: Add initial device tree
dt-bindings: arm: qcom: Add msm8916 based LG devices
ARM: dts: qcom: msm8960: correct memory base
arm64: dts: qcom: ipq9574: Add icc provider ability to gcc
dt-bindings: interconnect: Add Qualcomm IPQ9574 support
arm64: dts: qcom: sm8150: Add video clock controller node
arm64: dts: qcom: pm6150: Add vibrator
...
The Allwinner H616 SoC contains a crypto engine very similar to the H6
version, but with all base addresses in the DMA descriptors shifted by
two bits. This requires a new compatible string.
Also the H616 CE relies on the internal osciallator for the TRNG
operation, so we need to reference this clock.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20240624232110.9817-5-andre.przywara@arm.com
[wens@csie.org: fix up register range size]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Allwinner H616 contains a scatter-gather IOMMU connected to some
video related devices. It's almost compatible to the one used in the H6,
though with minor incompatibilities.
Add the DT node describing its resources, so that devices like the video
or display engine can connect to it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Ryan Walklin <ryan@testtoast.com>
Link: https://lore.kernel.org/r/20240616224056.29159-6-andre.przywara@arm.com
[wens@csie.org: Move IOMMU node after GIC node for address order]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Anbernic RG35XX device variants (-2024, -H, -Plus and -SP) are the
only currently known devices to have an Allwinner H700 SoC. The closely
related RG28XX also has the H700 but a mainline DT for this device has
not yet been submitted.
Include the H616 CPU OPP table in the base device DTS, and increase the
DCDC1 regulator (vdd-cpu) upper voltage range to 1.16V, allowing the
CPU to reach 1.5GHz.
Signed-off-by: Ryan Walklin <ryan@testtoast.com>
Tested-by: Philippe Simons <simons.philippe@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20240607092140.33112-4-ryan@testtoast.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The H700 now shows stable operation with the 1.008, 1.032 and 1.512 GHz
DVFS operating points. The 1.5GHz OPP requires a VDD-CPU of 1.16V,
obtained from the vendor BSP. This voltage is slightly above the
recommended operating voltage for the H616 (H700 datasheet not publicly
available) but well within the absolute maximum of 1.3V.
Add the additional 1.032 GHz operating point to the H616 CPU-OPP table,
and enable the 1.008 and 1.512 points for the H700.
Signed-off-by: Ryan Walklin <ryan@testtoast.com>
Tested-by: Philippe Simons <simons.philippe@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20240607092140.33112-3-ryan@testtoast.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add support for the ADC joysticks found on the Anbernic RG35XX-H. The
joysticks use one channel of the GPADC which is muxed 4 ways by an ADC
mux.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240605172049.231108-5-macroalpha82@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The H616 has a GPADC controller which is identical to the one found on
the D1/T113s/R329/T507 SoCs.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240605172049.231108-4-macroalpha82@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add missing cache information to the Allwinner H616 SoC dtsi, to allow
the userspace, which includes lscpu(1) that uses the virtual files provided
by the kernel under the /sys/devices/system/cpu directory, to display the
proper H616 cache information.
Adding the cache information to the H616 SoC dtsi also makes the following
warning message in the kernel log go away:
cacheinfo: Unable to detect cache hierarchy for CPU 0
Rather conspicuously, almost no cache-related information is available in
the publicly available Allwinner H616 datasheet (version 1.0) and H616 user
manual (version 1.0). Thus, the cache parameters for the H616 SoC dtsi were
obtained and derived by hand from the cache size and layout specifications
found in the following technical reference manual, and from the cache size
and die revision hints available from the following community-provided data
and memory subsystem benchmarks:
- ARM Cortex-A53 revision r0p4 TRM, version J
- Summary of the two available H616 die revisions and their differences
in cache sizes observed from the CSSIDR_EL1 register readouts, provided
by Andre Przywara [1][2]
- Tinymembench benchmark results of the H616-based OrangePi Zero 2 SBC,
provided by Thomas Kaiser [3]
For future reference, here's a brief summary of the available documentation
and the community-provided data and memory subsystem benchmarks:
- All caches employ the 64-byte cache line length
- Each Cortex-A53 core has 32 KB of L1 2-way, set-associative instruction
cache and 32 KB of L1 4-way, set-associative data cache
- The size of the L2 cache depends on the actual H616 die revision (there
are two die revisions), so the entire SoC can have either 256 KB or 1 MB
of unified L2 16-way, set-associative cache [1]
Also for future reference, here's the relevant excerpt from the community-
provided H616 memory subsystem benchmark, [3] which confirms that 32 KB and
256 KB are the L1 data and L2 cache sizes, respectively:
block size : single random read / dual random read
1024 : 0.0 ns / 0.0 ns
2048 : 0.0 ns / 0.0 ns
4096 : 0.0 ns / 0.0 ns
8192 : 0.0 ns / 0.0 ns
16384 : 0.0 ns / 0.0 ns
32768 : 0.0 ns / 0.0 ns
65536 : 4.3 ns / 7.3 ns
131072 : 6.6 ns / 10.5 ns
262144 : 9.8 ns / 15.2 ns
524288 : 91.8 ns / 142.9 ns
1048576 : 138.6 ns / 188.3 ns
2097152 : 163.0 ns / 204.8 ns
4194304 : 178.8 ns / 213.5 ns
8388608 : 187.1 ns / 217.9 ns
16777216 : 192.2 ns / 220.9 ns
33554432 : 196.5 ns / 224.0 ns
67108864 : 215.7 ns / 259.5 ns
The changes introduced to the H616 SoC dtsi by this patch specify 256 KB as
the L2 cache size. As outlined by Andre Przywara, [2] a follow-up TF-A patch
will perform runtime adjustment of the device tree data, making the correct
L2 cache size of 1 MB present in the device tree for the boards based on the
revision of H616 that actually provides 1 MB of L2 cache.
[1] https://lore.kernel.org/linux-sunxi/20240430114627.0cfcd14a@donnerap.manchester.arm.com/
[2] https://lore.kernel.org/linux-sunxi/20240501103059.10a8f7de@donnerap.manchester.arm.com/
[3] https://raw.githubusercontent.com/ThomasKaiser/sbc-bench/master/results/4knM.txt
Suggested-by: Andre Przywara <andre.przywara@arm.com>
Helped-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/e4b9cc3e3d366a571e552c31dafa5de847bc1c12.1716914537.git.dsimic@manjaro.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add missing cache information to the Allwinner A64 SoC dtsi, to allow
the userspace, which includes lscpu(1) that uses the virtual files provided
by the kernel under the /sys/devices/system/cpu directory, to display the
proper A64 cache information.
While there, use a more self-descriptive label for the L2 cache node, which
also makes it more consistent with other SoC dtsi files.
The cache parameters for the A64 dtsi were obtained and partially derived
by hand from the cache size and layout specifications found in the following
datasheets and technical reference manuals:
- Allwinner A64 datasheet, version 1.1
- ARM Cortex-A53 revision r0p3 TRM, version E
For future reference, here's a brief summary of the documentation:
- All caches employ the 64-byte cache line length
- Each Cortex-A53 core has 32 KB of L1 2-way, set-associative instruction
cache and 32 KB of L1 4-way, set-associative data cache
- The entire SoC has 512 KB of unified L2 16-way, set-associative cache
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/6a772756c2c677dbdaaab4a2c71a358d8e4b27e9.1714304058.git.dsimic@manjaro.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add missing cache information to the Allwinner H6 SoC dtsi, to allow
the userspace, which includes lscpu(1) that uses the virtual files provided
by the kernel under the /sys/devices/system/cpu directory, to display the
proper H6 cache information.
Adding the cache information to the H6 SoC dtsi also makes the following
warning message in the kernel log go away:
cacheinfo: Unable to detect cache hierarchy for CPU 0
The cache parameters for the H6 dtsi were obtained and partially derived
by hand from the cache size and layout specifications found in the following
datasheets and technical reference manuals:
- Allwinner H6 V200 datasheet, version 1.1
- ARM Cortex-A53 revision r0p3 TRM, version E
For future reference, here's a brief summary of the documentation:
- All caches employ the 64-byte cache line length
- Each Cortex-A53 core has 32 KB of L1 2-way, set-associative instruction
cache and 32 KB of L1 4-way, set-associative data cache
- The entire SoC has 512 KB of unified L2 16-way, set-associative cache
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/49abb93000078c692c48c0a65ff677893909361a.1714304071.git.dsimic@manjaro.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add a DT node for the Allwinner H616 LRADC describing the base address,
interrupt, reset and clock gates.
Signed-off-by: James McGregor <jamcgregor@protonmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240426092924.15489-3-jamcgregor@protonmail.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The "r_intc" interrupt controller on the A64 uses a mapping scheme, so
the first (and only) NMI interrupt #0 appears as interrupt number 32
(cf. the top comment in drivers/irqchip/irq-sun6i-r.c).
Fix that number in the interrupts property to properly forward PMIC
interrupts to the CPU.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Fixes: 4d39a8eb07 ("arm64: dts: allwinner: Add Jide Remix Mini PC support")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20240515234852.26929-1-andre.przywara@arm.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
- Rework the handling of disabled turbo in the intel_pstate driver and
make it update the maximum CPU frequency consistently regardless of
the reason on top of a number of cleanups (Rafael Wysocki).
- Add missing checks for NULL .exit() cpufreq driver callback to the
cpufreq core (Viresh Kumar).
- Prevent pulicy->max from going above the frequency QoS maximum value
when cpufreq_frequency_table_verify() is used (Xuewen Yan).
- Prevent a negative CPU number or frequency value from being printed
if they are really large (Joshua Yeong).
- Update MAINTAINERS entry for amd-pstate to add two new submaintainers
and a designated reviewer (Huang Rui).
- Clean up the amd-pstate driver and update its documentation (Gautham
Shenoy).
- Fix the highest frequency issue in the amd-pstate driver which limits
performance (Perry Yuan).
- Enable CPPC v2 for certain processors in the family 17H, as requested
by TR40 processor users who expect improved performance and lower
system temperature (Perry Yuan).
- Change latency and delay values to be read from platform firmware
firstly for more accurate timing (Perry Yuan).
- A new quirk is introduced for supporting amd-pstate on legacy
processors which either lack CPPC capability, or only only have CPPC
v2 capability (Perry Yuan).
- Sun50i cpufreq: Add support for opp_supported_hw, H616 platform and
general cleanups (Andre Przywara, Martin Botka, Brandon Cheo Fusi,
Dan Carpenter, Viresh Kumar).
- CPPC cpufreq: Fix possible null pointer dereference (Aleksandr
Mishin).
- Eliminate uses of of_node_put() from cpufreq (Javier Carrasco,
Shivani Gupta).
- brcmstb-avs: ISO C90 forbids mixed declarations (Portia Stephens).
- mediatek cpufreq: Add support for MT7988A (Sam Shih).
- cpufreq-qcom-hw: Add SM4450 compatibles in DT bindings (Tengfei Fan).
- Fix struct cpudata::epp_cached kernel-doc in the intel_pstate cpufreq
driver (Jeff Johnson).
- Fix kerneldoc description of ladder_do_selection() (Jeff Johnson).
- Convert the cpuidle kirkwood driver to platform remove callback
returning void (Yangtao Li).
- Replace deprecated strncpy() with strscpy() in the hibernation core
code (Justin Stitt).
- Use %ps to simplify debug output in the core system-wide suspend and
resume code (Len Brown).
- Remove unnecessary else from device_init_wakeup() and make
device_wakeup_disable() return void (Dhruva Gole).
- Enable PMU support in the Intel TPMI RAPL driver (Zhang Rui).
- Add support for ArrowLake-H platform to the Intel RAPL driver (Zhang
Rui).
- Avoid explicit cpumask allocation on stack in DTPM (Dawei Li).
- Make the Samsung exynos-asv driver update the Energy Model after
adjusting voltage on top of some preliminary changes of the OPP and
Enery Model generic code (Lukasz Luba).
- Remove a reference to a function that has been dropped from the power
management documentation (Bjorn Helgaas).
- Convert the platfrom remove callback to .remove_new for the
exyno-nocp, exynos-ppmu, mtk-cci-devfreq, sun8i-a33-mbus, and
rk3399_dmc devfreq drivers (Uwe Kleine-König).
- Use DEFINE_SIMPLE_PM_OPS for exyno-bus.c driver (Anand Moon).
-----BEGIN PGP SIGNATURE-----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=el5Y
-----END PGP SIGNATURE-----
Merge tag 'pm-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These are mostly cpufreq updates, including a significant intel-pstate
driver update and several amd-pstate improvements plus some updates of
ARM cpufreq drivers, general fixes and cleanups.
Also included are changes related to system sleep, power capping
updates adding support for a new platform and a new hardware feature
(among other things), a Samsung exynos-asv driver update allowing it
to change its Energy Model after adjusting voltage, minor cpuidle and
devfreq updates and a small documentation cleanup.
Specifics:
- Rework the handling of disabled turbo in the intel_pstate driver
and make it update the maximum CPU frequency consistently
regardless of the reason on top of a number of cleanups (Rafael
Wysocki)
- Add missing checks for NULL .exit() cpufreq driver callback to the
cpufreq core (Viresh Kumar)
- Prevent pulicy->max from going above the frequency QoS maximum
value when cpufreq_frequency_table_verify() is used (Xuewen Yan)
- Prevent a negative CPU number or frequency value from being printed
if they are really large (Joshua Yeong)
- Update MAINTAINERS entry for amd-pstate to add two new
submaintainers and a designated reviewer (Huang Rui)
- Clean up the amd-pstate driver and update its documentation
(Gautham Shenoy)
- Fix the highest frequency issue in the amd-pstate driver which
limits performance (Perry Yuan)
- Enable CPPC v2 for certain processors in the family 17H, as
requested by TR40 processor users who expect improved performance
and lower system temperature (Perry Yuan)
- Change latency and delay values to be read from platform firmware
firstly for more accurate timing (Perry Yuan)
- A new quirk is introduced for supporting amd-pstate on legacy
processors which either lack CPPC capability, or only only have
CPPC v2 capability (Perry Yuan)
- Sun50i cpufreq: Add support for opp_supported_hw, H616 platform and
general cleanups (Andre Przywara, Martin Botka, Brandon Cheo Fusi,
Dan Carpenter, Viresh Kumar)
- CPPC cpufreq: Fix possible null pointer dereference (Aleksandr
Mishin)
- Eliminate uses of of_node_put() from cpufreq (Javier Carrasco,
Shivani Gupta)
- brcmstb-avs: ISO C90 forbids mixed declarations (Portia Stephens)
- mediatek cpufreq: Add support for MT7988A (Sam Shih)
- cpufreq-qcom-hw: Add SM4450 compatibles in DT bindings (Tengfei
Fan)
- Fix struct cpudata::epp_cached kernel-doc in the intel_pstate
cpufreq driver (Jeff Johnson)
- Fix kerneldoc description of ladder_do_selection() (Jeff Johnson)
- Convert the cpuidle kirkwood driver to platform remove callback
returning void (Yangtao Li)
- Replace deprecated strncpy() with strscpy() in the hibernation core
code (Justin Stitt)
- Use %ps to simplify debug output in the core system-wide suspend
and resume code (Len Brown)
- Remove unnecessary else from device_init_wakeup() and make
device_wakeup_disable() return void (Dhruva Gole)
- Enable PMU support in the Intel TPMI RAPL driver (Zhang Rui)
- Add support for ArrowLake-H platform to the Intel RAPL driver
(Zhang Rui)
- Avoid explicit cpumask allocation on stack in DTPM (Dawei Li)
- Make the Samsung exynos-asv driver update the Energy Model after
adjusting voltage on top of some preliminary changes of the OPP and
Enery Model generic code (Lukasz Luba)
- Remove a reference to a function that has been dropped from the
power management documentation (Bjorn Helgaas)
- Convert the platfrom remove callback to .remove_new for the
exyno-nocp, exynos-ppmu, mtk-cci-devfreq, sun8i-a33-mbus, and
rk3399_dmc devfreq drivers (Uwe Kleine-König)
- Use DEFINE_SIMPLE_PM_OPS for exyno-bus.c driver (Anand Moon)"
* tag 'pm-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (68 commits)
PM / devfreq: exynos: Use DEFINE_SIMPLE_DEV_PM_OPS for PM functions
PM / devfreq: rk3399_dmc: Convert to platform remove callback returning void
PM / devfreq: sun8i-a33-mbus: Convert to platform remove callback returning void
PM / devfreq: mtk-cci: Convert to platform remove callback returning void
PM / devfreq: exynos-ppmu: Convert to platform remove callback returning void
PM / devfreq: exynos-nocp: Convert to platform remove callback returning void
cpufreq: amd-pstate: fix the highest frequency issue which limits performance
cpufreq: intel_pstate: fix struct cpudata::epp_cached kernel-doc
cpuidle: ladder: fix ladder_do_selection() kernel-doc
powercap: intel_rapl_tpmi: Enable PMU support
powercap: intel_rapl: Introduce APIs for PMU support
PM: hibernate: replace deprecated strncpy() with strscpy()
cpufreq: Fix up printing large CPU numbers and frequency values
MAINTAINERS: cpufreq: amd-pstate: Add co-maintainers and reviewer
cpufreq: amd-pstate: remove unused variable lowest_nonlinear_freq
cpufreq: amd-pstate: fix code format problems
cpufreq: amd-pstate: Add quirk for the pstate CPPC capabilities missing
cppc_acpi: print error message if CPPC is unsupported
cpufreq: amd-pstate: get transition delay and latency value from ACPI tables
cpufreq: amd-pstate: Bail out if min/max/nominal_freq is 0
...
The RG35XX-H adds thumbsticks, a stereo speaker, and a second USB port to
the RG35XX-Plus, and has a horizontal form factor.
Enabled in this DTS:
- Thumbsticks
- Second USB port
Signed-off-by: Ryan Walklin <ryan@testtoast.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240427110225.727472-8-ryan@testtoast.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The RG35XX-Plus adds a RTL8221CS SDIO Wifi/BT chip to the RG35XX (2024).
Enabled in this DTS:
- WiFi
- Bluetooth
- Supporting power sequence and GPIOs
Signed-off-by: Ryan Walklin <ryan@testtoast.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240427110225.727472-7-ryan@testtoast.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The base model RG35XX (2024) is a handheld gaming device based on an
Allwinner H700 chip.
The H700 is a H616 variant (4x ARM Cortex-A53 cores @ 1.5Ghz with Mali G31
GPU) which exposes RGB LCD and NMI pins.
Device features:
- Allwinner H700 @ 1.5GHz
- 1GB LPDDR4 DRAM
- X-Powers AXP717 PMIC
- 3.5" 640x480 RGB LCD
- Two microSD slots
- Mini-HDMI out
- GPIO keypad
- 3.5mm headphone jack
- USB-C charging port
Enabled in this DTS:
- AXP717 PMIC with RSB serial interface, regulators and NMI interrupt
controller
- Power LED (charge LED on device controlled directly by PMIC)
- Serial UART (accessible from headers on the board)
- First SD slot (SD2 appears to have a GPIO-switched regulator for 1.8v
low-voltage signalling, this is not yet modeled. Enablement with a
switched regulator will be confirmed and posted in a follow-up patch).
Signed-off-by: Ryan Walklin <ryan@testtoast.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20240427110225.727472-6-ryan@testtoast.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Add device node for the H616 Non Maskable Interrupt (NMI) controller.
This controller is present on all H616 boards and derivatives such as
the T507 and H700. Note that on the H616 no NMI pad is exposed.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240418181615.1370179-3-macroalpha82@gmail.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The Tanix TX1 is a tiny TV box with the Allwinner H313 SoC. The box
features no Ethernet or an SD card slot, which makes booting from it
somewhat interesting: Pressing the hidden FEL button and using a USB-A
to USB-A cable to upload code from a host PC is one way to run mainline.
The box features:
- Allwinner H313 SoC (4 * Arm Cortex-A53 cores)
- 1 or 2 GB DRAM
- 8 or 16 GB eMMC flash
- SCI S9082H WiFi chip
- HDMI port
- one USB 2.0 port
- 3.5mm AV port
- barrel plug 5V DC input via barrel plug
The devicetree covers most peripherals.
The eMMC did not work properly in HS200 speed mode, so this mode property
is omitted. HS-DDR seems to work fine.
The blue LED is connected to the same GPIO pin as the red LED, just
using the opposite polarity. Apparently there is no way of describing
this in DT, so the red LED is omitted.
Next to the FEL button is a hidden button, that can be pushed by using
something like a paperclip, through the ventilation vents of the case.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240418104942.1556914-3-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
With the DT bindings now describing the format of the CPU OPP tables, we
can include the OPP table in each board's .dts file, and specify the CPU
power supply.
This allows to enable DVFS, and get up to 50% of performance benefit in
the highest OPP, or up to 60% power savings in the lowest OPP, compared
to the fixed 1GHz @ 1.0V OPP we are running in by default at the moment.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Add an Operating Performance Points table for the CPU cores to enable
Dynamic Voltage & Frequency Scaling (DVFS) on the H616.
The values were taken from the BSP sources. There is a separate OPP set
seen on some H700 devices, but they didn't really work out in testing, so
they are not included for now.
Also add the needed cpu_speed_grade nvmem cell and the cooling cells
properties, to enable passive cooling.
Signed-off-by: Martin Botka <martin.botka@somainline.org>
[Andre: rework to minimise opp-microvolt properties]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Currently we specify the pins for the I2C0 function as PI6 and PI7, even
though they are actually PI5 and PI6. Linux' pinctrl driver and the H616
user manual confirm this.
Fix the pin names in the pins property. None of the existing DTs in the
tree seems to use I2C0, which explains why this went unnoticed.
Fixes: 0d17c86511 ("arm64: dts: allwinner: Add Allwinner H616 .dtsi file")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240329103825.25463-1-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The Allwinner A64's GPU has currently three operating points. However,
the BSP runs the GPU fixed at 432 MHz. In addition, at least one of the
devices using that SoC - the pinephone - shows unstabilities (see link)
that can be circumvented by running the GPU at a fixed rate.
Therefore, remove the other two operating points from the GPU OPP table,
so that the GPU runs at a fixed rate of 432 MHz.
Link: https://gitlab.com/postmarketOS/pmaports/-/issues/805
Acked-by: Erico Nunes <nunes.erico@gmail.com>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240310-pinephone-pll-fixes-v4-5-46fc80c83637@oltmanns.dev
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Underscores should not be used in node names (dtc with W=2 warns about
them), so replace them with hyphens. Use also generic name for pwrseq
node, because generic naming is favored by Devicetree spec. All the
clocks affected by this change use clock-output-names, so resulting
clock name should not change. Functional impact checked with comparing
before/after DTBs with dtx_diff and fdtdump.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240317184130.157695-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
There is no "reg_gmac_3v3" device node in sun50i-h6-pine-h64.dts,
although there is "gmac-3v3" with "reg_gmac_3v3" label, so let's assume
author wanted to remove that node. Delete node via phandle, not via
full node path, to fix this.
Fixes: f33a911750 ("arm64: dts: allwinner: add pineh64 model B")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240317184130.157695-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The red, green, and blue LEDs currently in the device tree represent a
single RGB LED on the front of the PinePhone.
Signed-off-by: Aren Moynihan <aren@peacevolution.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240317004116.1473967-2-aren@peacevolution.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Allows user to set a LED before entering suspend to know that
the phone is still on (or could be used for notifications etc).
Signed-off-by: Miles Alan <m@milesalan.com>
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Aren Moynihan <aren@peacevolution.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240317004116.1473967-1-aren@peacevolution.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
There are four thermal sensors:
- CPU
- GPU
- VE
- DRAM
Add the thermal sensor configuration and the thermal zones.
Signed-off-by: Martin Botka <martin.botka@somainline.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240219153639.179814-8-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The Sipeed Longan SoM 3H is a system on module based on the Allwinner
H618 SoC. The SoM features:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 2/4 GiB LPDDR4 DRAM SoMs
- AXP313a PMIC
- eMMC
The Sipeed Longan PI 3H is a development board based on the above SoM.
The board features:
- Longan SoM 3H
- Raspberry-Pi-1 compatible GPIO header
- 2 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- 1Gbps Ethernet port (via RTL8211 PHY)
- HDMI port
- WiFi/BT chip
Add the devicetree file describing the currently supported features,
namely PMIC, LEDs, UART, SD card, eMMC, USB and Ethernet.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240211081739.395-3-jszhang@kernel.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The DTS code coding style expects exactly one space before '{'
character.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240208105301.129005-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Documentation/process/license-rules.rst and checkpatch expect the SPDX
identifier syntax for multiple licenses to use capital "OR". Correct it
to keep consistent format and avoid copy-paste issues.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240208105301.129005-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
In contrast to other devices using Allwinner SoCs, the Transpeed 8K618-T
TV box uses a mainline supported WiFi chip: it's Broadcom 4335 compatible,
packaged by Murata.
Add the required DT nodes to let DT users know about the SDIO device.
There is an otherwise empty MMC device node, to receive the MAC address,
that firmware might want to write in there.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240209115759.3582869-3-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
On some boards the designers saved on a 32KHz crystal for some external
chips, so the SoC has to help out, with providing a 32 KHz clock signal.
Add a pinctrl group node to allow DT nodes to reference this fanout signal.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240209115759.3582869-2-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The Remix Mini PC is a "mini computer" using the Allwinner H64 SoC,
which appears to be just a relabelled A64. It was launched in 2015 by
the now defunct company Jide, and shipped with a desktop optimised
version of Android. It features
- Allwinner H64 Soc (4 * Arm Cortex-A53 cores)
- 1 or 2 GB DRAM
- 8 or 16 GB eMMC flash
- 100 MBit Ethernet port (using an X-Powers AC200 PHY)
- RTL8723BS WiFi & Bluetooth chip
- HDMI port
- two USB 2.0 ports
- 3.5mm AV port
- microSD card slot
The devicetree covers most peripherals, though there is no agreed
binding for the PHY chip yet, so this is left out.
The eMMC did not work with the MMC DDR speed mode, so this mode property
is omitted.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240209114018.3580370-4-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The H616 SoC has an SPDIF transmitter hardware block, which has the same
layout as the one in the H6, minus the receiver side.
Add a device node for it, and a default pinmux.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240127163247.384439-8-wens@kernel.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The DMA controllers found on the H616 and H618 are the same as the one
found on the A100. The only difference is the DMA endpoint (DRQ) layout.
Add a device node for it, and add DMA channels for existing peripherals.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20240127163247.384439-7-wens@kernel.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The SPDIF hardware found on the H6 supports both transmit and receive
functions. However it is missing the RX DMA channel.
Add the SPDIF hardware block's RX DMA channel. Also remove the
by-default pinmux, since the end device can choose to implement
either or both functionalities.
Fixes: f95b598df4 ("arm64: dts: allwinner: Add SPDIF node for Allwinner H6")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240127163247.384439-6-wens@kernel.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Orange Pi Zero 2W dts file is not included in Makefile. Fix this.
Fixes: c505ee1eae ("arm64: dts: allwinner: h616: add Orange Pi Zero 2W support")
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20240222211326.114955-1-jernej.skrabec@gmail.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
There is one new SoC for each 32-bit Arm and 64-bit RISC-V, but both
the Rockchips rv1109 and Sopgho CV1812H are just minor variations of
already supported chips.
The other six new SoCs are all part of existing arm64 families, but
are somewhat more interesting:
- Samsung ExynosAutov920 is an automotive chip, and the first one
we support based on the Cortex-A78AE core with lockstep mode.
- Google gs101 (Tensor G1) is the chip used in a number of Pixel phones,
and is grouped with Samsung Exynos here since it is based on the same
SoC design, sharing most of its IP blocks with that series.
- MediaTek MT8188 is a new chip used for mid-range tablets and Chromebooks,
using two Cortex-A78 cores where the older MT8195 had four of them.
- Qualcomm SM8650 (Snapdragon 8 Gen 3) is their current top range
phone SoC and the first supported chip based on Cortex-X4, Cortex-A720
and Cortex-A520.
- Qualcomm X1E80100 (Snapdragon X Elite) in turn is the latest
Laptop chip using the custom Oryon cores.
- Unisoc UMS9620 (Tanggula 7 series) is a 5G phone SoC based on
Cortex-A76 and Cortex-A55
In terms of boards, we have
- Five old Microsoft Lumia phones, the HTC One Mini 2, Motorola Moto
G 4G, and Huawei Honor 5X/GR5, all based on Snapdragon SoCs.
- Multiple Rockchips mobile gaming systems (Anbernic RG351V,
Powkiddy RK2023, Powkiddy X55) along with the Sonoff iHost Smart
Home Hub and a few Rockchips SBCs
- Some ComXpress boards based on Marvell CN913x, which is the
follow-up to Armada 7xxx/8xxx.
- Six new industrial/embedded boards based on NXP i.MX8 and i.MX9
- Mediatek MT8183 based Chromebooks from Lenovo, Asus and Acer.
- Toradex Verdin AM62 Mallow carrier for TI AM62
- Huashan Pi board based on the SophGo CV1812H RISC-V chip
- Two boards based on Allwinner H616/H618
- A number of reference boards for various added SoCs from Qualcomm,
Mediatek, Google, Samsung, NXP and Spreadtrum
As usual, there are cleanups and warning fixes across all platforms as
well as added features for several of them.
-----BEGIN PGP SIGNATURE-----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=zR3G
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC DT updates from Arnd Bergmann:
"There is one new SoC for each 32-bit Arm and 64-bit RISC-V, but both
the Rockchips rv1109 and Sopgho CV1812H are just minor variations of
already supported chips.
The other six new SoCs are all part of existing arm64 families, but
are somewhat more interesting:
- Samsung ExynosAutov920 is an automotive chip, and the first one we
support based on the Cortex-A78AE core with lockstep mode.
- Google gs101 (Tensor G1) is the chip used in a number of Pixel
phones, and is grouped with Samsung Exynos here since it is based
on the same SoC design, sharing most of its IP blocks with that
series.
- MediaTek MT8188 is a new chip used for mid-range tablets and
Chromebooks, using two Cortex-A78 cores where the older MT8195 had
four of them.
- Qualcomm SM8650 (Snapdragon 8 Gen 3) is their current top range
phone SoC and the first supported chip based on Cortex-X4,
Cortex-A720 and Cortex-A520.
- Qualcomm X1E80100 (Snapdragon X Elite) in turn is the latest Laptop
chip using the custom Oryon cores.
- Unisoc UMS9620 (Tanggula 7 series) is a 5G phone SoC based on
Cortex-A76 and Cortex-A55
In terms of boards, we have
- Five old Microsoft Lumia phones, the HTC One Mini 2, Motorola Moto
G 4G, and Huawei Honor 5X/GR5, all based on Snapdragon SoCs.
- Multiple Rockchips mobile gaming systems (Anbernic RG351V, Powkiddy
RK2023, Powkiddy X55) along with the Sonoff iHost Smart Home Hub
and a few Rockchips SBCs
- Some ComXpress boards based on Marvell CN913x, which is the
follow-up to Armada 7xxx/8xxx.
- Six new industrial/embedded boards based on NXP i.MX8 and i.MX9
- Mediatek MT8183 based Chromebooks from Lenovo, Asus and Acer.
- Toradex Verdin AM62 Mallow carrier for TI AM62
- Huashan Pi board based on the SophGo CV1812H RISC-V chip
- Two boards based on Allwinner H616/H618
- A number of reference boards for various added SoCs from Qualcomm,
Mediatek, Google, Samsung, NXP and Spreadtrum
As usual, there are cleanups and warning fixes across all platforms as
well as added features for several of them"
* tag 'soc-dt-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (857 commits)
ARM: dts: usr8200: Fix phy registers
arm64: dts: intel: minor whitespace cleanup around '='
arm64: dts: socfpga: agilex: drop redundant status
arm64: dts: socfpga: agilex: add unit address to soc node
arm64: dts: socfpga: agilex: move firmware out of soc node
arm64: dts: socfpga: agilex: move FPGA region out of soc node
arm64: dts: socfpga: agilex: align pin-controller name with bindings
arm64: dts: socfpga: stratix10_swvp: drop unsupported DW MSHC properties
arm64: dts: socfpga: stratix10_socdk: align NAND chip name with bindings
arm64: dts: socfpga: stratix10: add unit address to soc node
arm64: dts: socfpga: stratix10: move firmware out of soc node
arm64: dts: socfpga: stratix10: move FPGA region out of soc node
arm64: dts: socfpga: stratix10: align pincfg nodes with bindings
arm64: dts: socfpga: stratix10: add clock-names to DWC2 USB
arm64: dts: socfpga: drop unsupported cdns,page-size and cdns,block-size
ARM: dts: socfpga: align NAND controller name with bindings
ARM: dts: socfpga: drop unsupported cdns,page-size and cdns,block-size
arm64: dts: rockchip: Fix led pinctrl of lubancat 1
arm64: dts: rockchip: correct gpio_pwrctrl1 typo on nanopc-t6
arm64: dts: rockchip: correct gpio_pwrctrl1 typo on rock-5b
...
This is a Chinese TV box, probably very similar if not identical to
various other cheap TV boxes with the same specs:
- Allwinner H618 SoC (4 * Arm Cortex-A53 cores, 1MB L2 cache)
- 2 or 4GiB DDR3L DRAM
- 32, 64, or 128 GiB eMMC flash
- AXP313a PMIC
- 100 Mbit/s Ethernet (using yet unsupported internal PHY)
- HDMI port
- 2 * USB 2.0 ports
- microSD card slot
- 3.5mm A/V port
- 7-segment display
- 5V barrel plug power supply
The PCB provides holes for soldering a UART header or cable, this is
connected to the debug UART0. UART1 is used for the Bluetooth chip,
although this isn't working yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20231214015312.17363-4-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The current emac setting is not suitable for Orange Pi Zero 3,
move it back to Orange Pi Zero 2 DT. Also update phy mode and
delay values for emac on Orange Pi Zero 3.
With these changes, Ethernet now looks stable.
Fixes: 322bf10320 ("arm64: dts: allwinner: h616: Split Orange Pi Zero 2 DT")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20231029074009.7820-2-amadeus@jmu.edu.cn
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The Orange Pi Zero 2W is a board based on the Allwinner H618 SoC.
It uses the RaspberryPi Zero form factor, with an optional expansion
board, connected via an FPC connector, to provide more connectors.
The base board features:
- Allwinner H618 SoC (quad Cortex-A53 cores, with 1MB L2 cache)
- 1, 2 or 4GB of LPDDR4 DRAM
- SD card socket
- two USB-C sockets, one UFP, one DFP
- HDMI connector
- (yet unsupported) WiFi module
- 16 MiB SPI flash
- power supply via the UFP USB-C port
The FPC connector provides access to two more USB host ports, Fast
Ethernet, some GPIOs, Audio Line out and the IR receiver pin.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20231020145706.705420-3-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The BigTreeTech Pi is an H616 based board based on CB1.
Just in Rpi format board.
It features the same internals as BTT CB1 but adds:
- Fan port
- IR receiver
- ADXL345 Accelerometer connector via SPI
- 24V DC power supply via terminal plugs
- USB to CAN module connector (External Module)
List of currently working things is same as BTT CB1 but also:
- IR receiver
- ADXL345 connector
Signed-off-by: Martin Botka <martin@biqu3d.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230912-b4-cb1-v6-4-bb11238f3a9c@somainline.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
CB1 is Compute Module style board that plugs into Rpi board style adapter or
Manta 3D printer boards (M4P/M8P).
The SoM features:
- H616 SoC
- 1GiB of RAM
- AXP313A PMIC
- RTL8189FTV WiFi
Boards feature:
- 4x USB via USB2 hub (usb1 on SoM).
- SDcard slot for loading images.
- Ethernet port wired to the internal PHY. (100M)
- 2x HDMI 2.0. (Only 1 usable on CB1)
- Power and Status LEDs. (Only Status LED usable on CB1)
- 40 pin GPIO header
Currently working:
- Booting
- USB
- UART
- MMC
- Status LED
- WiFi (RTL8189FS via out of tree driver)
I didnt want to duplicate things so the manta DTS can also be used on BTT pi4b adapter.
CB1 SoM has its own DTSI file in case other boards shows up that accept this SoM.
Signed-off-by: Martin Botka <martin.botka@somainline.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230912-b4-cb1-v6-3-bb11238f3a9c@somainline.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The OrangePi Zero 3 is a development board based on the Allwinner H618 SoC,
which seems to be just an H616 with more L2 cache. The board itself is a
slightly updated version of the Orange Pi Zero 2. It features:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 1/1.5/2/4 GiB LPDDR4 DRAM SKUs (only up to 1GB on the Zero2)
- AXP313a PMIC (more capable AXP305 on the Zero2)
- Raspberry-Pi-1 compatible GPIO header
- extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
- 1 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- on-board 16MiB bootable SPI NOR flash (only 2MB on the Zero2)
- 1Gbps Ethernet port (via Motorcomm YT8531 PHY) (RTL8211 on the Zero2)
- micro-HDMI port
- (yet) unsupported Allwinner WiFi/BT chip
Add the devicetree file describing the currently supported features,
namely LEDs, SD card, PMIC, SPI flash, USB. Ethernet seems unstable at
the moment, though the basic functionality works.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230804170856.1237202-4-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The Orange Pi Zero 2 got a successor (Zero 3), which shares quite some
DT nodes with the Zero 2, but comes with a different PMIC.
Move the common parts (except the PMIC) into a new shared file, and
include that from the existing board .dts file.
No functional change, the generated DTB is the same, except for some
phandle numbering differences.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230804170856.1237202-2-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.
There's no change to dtbs_install as the flat structure is maintained on
install.
The naming of vendor directories is roughly in this order of preference:
- Matching original and current SoC vendor prefix/name (e.g. ti, qcom)
- Current vendor prefix/name if still actively sold (SoCs which have
been aquired) (e.g. nxp/imx)
- Existing platform name for older platforms not sold/maintained by any
company (e.g. gemini, nspire)
The whole move was scripted with the exception of MAINTAINERS and a few
makefile fixups.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com> #Xilinx
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Paul Barker <paul.barker@sancloud.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Wei Xu <xuwei5@hisilicon.com> #hisilicon
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #broadcom
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
While the rate of TCON0's DCLK matches dotclock for parallel and LVDS
outputs, this doesn't hold for DSI. According manuals from Allwinner,
DCLK is an abbreviation of Data Clock, not dotclock, so go with that
instead.
Signed-off-by: Roman Beranek <me@crly.cz>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20230505052110.67514-3-me@crly.cz
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
As all level 2 and level 3 caches are unified, add required
cache-unified property to fix warnings like:
sun50i-a64-pine64-lts.dtb: l2-cache: 'cache-unified' is a required property
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230421223137.115015-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
So far the OrangePi PC2 board was running at a fixed frequency, set by
U-Boot to 816 MHz, which is the best achievable frequency at the 1.1V
CPU voltage provided by the PMIC at reset.
We already describe the CPU voltage regulator in the DT, but were
missing the OPP table. Just include the default H5 OPP table, as used
by other boards. My OrangePi PC2 runs just fine with those values, and
now goes up to 1.15 GHz.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230228114112.3340715-1-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The devicetree changes contain exactly 1000 non-merge changesets,
including a number of new arm64 SoC variants from Qualcomm and Apple,
as well as the Renesas r9a07g043f/u chip in both arm64 and riscv variants
While we have occasionally merged support for non-arm SoCs in the past,
this is now the normal path for riscv devicetree files.
The most notable changes, by SoC platform, are:
- The Apple T6000 (M1 Pro), T6001 (M1 Max) and T6002 (M2 Ultra)
chips now have initial support. This is particularly nice as I am
typing this on a T6002 Mac Studio with only a small number of driver
patches.
- Qualcomm MSM8996 Pro (Snapdragon 821), SM6115 (Snapdragon 662), SM4250
(Snapdragon 460), SM6375 (Snapdragon 695), SDM670 (Snapdragon 670),
MSM8976 (Snapdragon 652) and MSM8956 (Snapdragon 650) are all mobile
phone chips that are closely related to others we already support.
Adding those helps support more phones and we add several models
from Sony (Xperia 10 IV, 5 IV, X, and X compact), OnePlus (One, 3,
3T, and Nord N100), Xiaomi (Poco F1, Mi6), Huawei (Watch) and Google
(Pixel 3a). There are also new variants of the Herobrine and Trogdor
chromebook motherboards. SA8540P is an automotive SoC used in the
Qdrive-3 development platform
- Rockchips gains no new SoC variants, but a lot of new boards:
three mobile gaming systems based on RK3326 Odroid-Go/rg351 family,
two more Anbernic gaming systems based on RK3566 and a number of
other RK356x based single-board computers.
- Renesas RZ/G2UL (r9a07g043) was already supported for arm64, but as
the newly added RZ/Five is based on the same design, this now gets
reorganized in order to share most of the dts description between
the two and add the RZ/Five SMARC EVK board support.
Aside from that, there are the usual changes all over the tree:
- New boards on other platforms contain two ASpeed BMC users, two
Broadcom based Wifi routers, Zyxel NSA310S NAS, the i.MX6 based Kobo
Aura2 ebook reader, two i.MX8 based development boards, two Uniphier
Pro5 development boards, the STM32MP1 testbench board from DHCOR,
the TI K3 based BeagleBone AI-64 board, and the Mediatek Helio X10
based Sony Xperia M5 phone.
- The Starfive JH7100 source gets reorganized in order to support the
VisionFive V1 board.
- Minor updates and cleanups for Intel SoCFPGA, Marvell PXA168,
TI, ST, NXP, Apple, Broadcom, Juno, Marvell MVEBU, at91, nuvoton,
Tegra, Mediatek, Renesas, Hisilicon, Allwinner, Samsung, ux500,
spear, ... The treewide cleanups now have a lot of fixes for cache
nodes and other binding violoations.
- Somewhat larger sets of reworks for NVIDIA Tegra, Qualcomm
and Renesas platforms, adding a lot more on-chip device support
- A rework of the way that DTB overlays are built.
-----BEGIN PGP SIGNATURE-----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=WCFd
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC DT updates from Arnd Bergmann:
"The devicetree changes contain exactly 1000 non-merge changesets,
including a number of new arm64 SoC variants from Qualcomm and Apple,
as well as the Renesas r9a07g043f/u chip in both arm64 and riscv
variants.
While we have occasionally merged support for non-arm SoCs in the
past, this is now the normal path for riscv devicetree files.
The most notable changes, by SoC platform, are:
- The Apple T6000 (M1 Pro), T6001 (M1 Max) and T6002 (M1 Ultra) chips
now have initial support. This is particularly nice as I am typing
this on a T6002 Mac Studio with only a small number of driver
patches.
- Qualcomm MSM8996 Pro (Snapdragon 821), SM6115 (Snapdragon 662),
SM4250 (Snapdragon 460), SM6375 (Snapdragon 695), SDM670
(Snapdragon 670), MSM8976 (Snapdragon 652) and MSM8956 (Snapdragon
650) are all mobile phone chips that are closely related to others
we already support.
Adding those helps support more phones and we add several models
from Sony (Xperia 10 IV, 5 IV, X, and X compact), OnePlus (One, 3,
3T, and Nord N100), Xiaomi (Poco F1, Mi6), Huawei (Watch) and
Google (Pixel 3a).
There are also new variants of the Herobrine and Trogdor chromebook
motherboards. SA8540P is an automotive SoC used in the Qdrive-3
development platform
- Rockchips gains no new SoC variants, but a lot of new boards: three
mobile gaming systems based on RK3326 Odroid-Go/rg351 family, two
more Anbernic gaming systems based on RK3566 and a number of other
RK356x based single-board computers.
- Renesas RZ/G2UL (r9a07g043) was already supported for arm64, but as
the newly added RZ/Five is based on the same design, this now gets
reorganized in order to share most of the dts description between
the two and add the RZ/Five SMARC EVK board support.
Aside from that, there are the usual changes all over the tree:
- New boards on other platforms contain two ASpeed BMC users, two
Broadcom based Wifi routers, Zyxel NSA310S NAS, the i.MX6 based
Kobo Aura2 ebook reader, two i.MX8 based development boards, two
Uniphier Pro5 development boards, the STM32MP1 testbench board from
DHCOR, the TI K3 based BeagleBone AI-64 board, and the Mediatek
Helio X10 based Sony Xperia M5 phone.
- The Starfive JH7100 source gets reorganized in order to support the
VisionFive V1 board.
- Minor updates and cleanups for Intel SoCFPGA, Marvell PXA168, TI,
ST, NXP, Apple, Broadcom, Juno, Marvell MVEBU, at91, nuvoton,
Tegra, Mediatek, Renesas, Hisilicon, Allwinner, Samsung, ux500,
spear, ... The treewide cleanups now have a lot of fixes for cache
nodes and other binding violoations.
- Somewhat larger sets of reworks for NVIDIA Tegra, Qualcomm and
Renesas platforms, adding a lot more on-chip device support
- A rework of the way that DTB overlays are built"
* tag 'soc-dt-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (979 commits)
arm64: dts: apple: t6002: Fix GPU power domains
arm64: dts: apple: t600x-pmgr: Fix search & replace typo
arm64: dts: apple: Add t8103 L1/L2 cache properties and nodes
arm64: dts: apple: Rename dart-sio* to sio-dart*
arch: arm64: apple: t600x: Use standard "iommu" node name
arch: arm64: apple: t8103: Use standard "iommu" node name
ARM: dts: socfpga: Fix pca9548 i2c-mux node name
dt-bindings: iio: adc: qcom,spmi-vadc: fix PM8350 define
dt-bindings: iio: adc: qcom,spmi-vadc: extend example
arm64: dts: qcom: sc8280xp: fix UFS DMA coherency
arm64: dts: qcom: sc7280: Add DT for sc7280-herobrine-zombie
arm64: dts: qcom: sm8250-sony-xperia-edo: fix no-mmc property for SDHCI
arm64: dts: qcom: sdm845-sony-xperia-tama: fix no-mmc property for SDHCI
arm64: dts: qcom: sda660-inforce-ifc6560: fix no-mmc property for SDHCI
arm64: dts: qcom: sa8155p-adp: fix no-mmc property for SDHCI
arm64: dts: qcom: qrb5165-rb: fix no-mmc property for SDHCI
arm64: dts: qcom: sm8450: align MMC node names with dtschema
arm64: dts: qcom: sc7180-trogdor: use generic node names
arm64: dts: qcom: sm8450-hdk: add sound support
arm64: dts: qcom: sm8450: add Soundwire and LPASS
...
The Hantro G2 video decoder block sits behind the IOMMU. Without a
reference for the system to properly configure the IOMMU, it will fault
and cause the video decoder to fail.
Add a proper reference to the IOMMU port. The master ID is taken from
the IOMMU fault error message on Linux, and the number seems to match
the order in the user manual's IOMMU diagram.
Fixes: 0baddea60e ("arm64: dts: allwinner: h6: Add Hantro G2 node")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221115090644.3602573-3-wenst@chromium.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Pinebook has an RTL8723CS WiFi + BT chip. BT is connected to UART1
and uses PL5 as device wake GPIO and PL6 as host wake GPIO.
Enable it in the device tree.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Bastian Germann <bage@debian.org>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20221105153319.19345-2-bage@debian.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The X96 Mate TV box has two USB-A ports, VBUS is always on and connected
to the DC input.
Since USB port 0 is connected to an USB-A receptable, we configure it
as a host port. Using it as a peripheral is dangerous, because VBUS is
always on.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221031111358.3387297-8-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The OrangePi Zero 2 has one USB-A host port, VBUS is provided by
a GPIO controlled regulator.
The USB-C port is meant to power the board, but is also connected to
the USB 0 port, which we configure as an MUSB peripheral.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221031111358.3387297-7-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Add the nodes for the MUSB and the four USB host controllers to the SoC
.dtsi, along with the PHY node needed to bind all of them together.
EHCI/OHCI and MUSB are compatible to previous SoCs, but the PHY requires
some quirks (handled in the driver).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221031111358.3387297-6-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The "ldo-io0" and "ldo-io1" regulators are enabled/disabled by toggling
the pinmux between two functions. This happens in the regulator driver.
Setting the pinmux to "ldo" in the DT is inappropriate because it would
enable the regulator before the driver has a chance to set the correct
initial voltage.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220916042751.47906-2-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Add an Operating Performance Points table for the GPU to
enable Dynamic Voltage & Frequency Scaling on the H6.
The voltage range is set with minimal voltage set to the target
and the maximal voltage set to 1.2V. This allow DVFS framework to
work properly on board with fixed regulator.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220906153034.153321-4-peron.clem@gmail.com
Add a simple cooling map for the GPU.
This cooling map come from the vendor kernel 4.9 with a
2°C hysteresis added.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220906153034.153321-3-peron.clem@gmail.com
The I2C controllers in the A100 SoC are all connected to the DMA engine.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220830020824.62288-4-samuel@sholland.org
The A100 SoC has a DMA controller that supports 8 DMA channels
to and from various peripherals.
Add a device node for it.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220830020824.62288-3-samuel@sholland.org
The X96 Mate is an Allwinner H616 based TV box, featuring:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 2GiB/4GiB RAM (fully usable!)
- 16/32/64GiB eMMC
- 100Mbps Ethernet (via embedded AC200 EPHY, not yet supported)
- Unsupported Allwinner WiFi chip
- 2 x USB 2.0 host ports
- HDMI port
- IR receiver
- 5V/2A DC power supply via barrel plug
Add a basic devicetree for it, with SD card and eMMC working, as
well as serial and the essential peripherals, like the AXP PMIC.
This DT is somewhat minimal, and should work on many other similar TV
boxes with the Allwinner H616 chip.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220708105235.3983266-8-andre.przywara@arm.com
The OrangePi Zero 2 is a development board with the new H616 SoC. It
comes with the following features:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 512MiB/1GiB DDR3 DRAM
- AXP305 PMIC
- Raspberry-Pi-1 compatible GPIO header
- extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
- 1 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- on-board 2MiB bootable SPI NOR flash
- 1Gbps Ethernet port (via RTL8211F PHY)
- micro-HDMI port
- (yet) unsupported Allwinner WiFi/BT chip
Add the devicetree file describing the currently supported features.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220708105235.3983266-7-andre.przywara@arm.com
This (relatively) new SoC is similar to the H6, but drops the (broken)
PCIe support and the USB 3.0 controller. It also gets the management
controller removed, which in turn removes *some*, but not all of the
devices formerly dedicated to the ARISC (CPUS).
And while there is still the extra sunxi interrupt controller, the
package lacks the corresponding NMI pin, so no interrupts for the PMIC.
The reserved memory node is actually handled by Trusted Firmware now,
but U-Boot fails to propagate this to a separately loaded DTB, so we
keep it in here for now, until U-Boot learns to do this properly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220708105235.3983266-4-andre.przywara@arm.com
Revisions 1.0 and 1.1 of the PinePhone mainboard do not have an external
resistor connecting HBIAS to MIC2P. Enable the internal resistor to
provide the necessary headeset microphone bias.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220621035452.60272-4-samuel@sholland.org
The I2C controllers in the A100 SoC are newer-generation hardware
which includes an offload engine. Signify that by including the
allwinner,sun8i-v536-i2c fallback compatible, as V536 is the first
SoC with this generation of I2C controller.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220702052544.31443-2-samuel@sholland.org
"status" does not match any pattern in the gpio-leds binding. Rename the
node to the preferred pattern. This fixes a `make dtbs_check` error.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220702132816.46456-1-samuel@sholland.org
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220609113911.380368-4-krzysztof.kozlowski@linaro.org
The binding header provides descriptive names for the RTC clock indexes,
since the indexes were arbitrarily chosen by the binding, not by the
hardware. Let's use the names, so the meaning is clearer.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220607012438.18183-2-samuel@sholland.org
Allwinner A64 SoC has separate supplies for PC, PD, PE, PG and PL.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220430191009.73946-1-harald@ccbib.org
Enable the audio hardware on the Olimex A64-OLinuXino board family.
Tested on the A64-OLinuXino-2Ge8G-IND variant.
Signed-off-by: Philip Rinn <rinni@inventati.org>
Acked-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220407155145.10891-1-rinni@inventati.org
As usual, this is the bulk of the updates for the SoC tree, adding
more devices to existing files, addressing issues from ever improving
automated checking, and fixing minor issues.
The most interesting bits as usual are the new platforms.
All the newly supported SoCs belong into existing families
this time:
- Qualcomm gets support for two newly announced platforms, both
of which can now work in production environments: the SDX65
5G modem that can run a minimal Linux on its Cortex-A7 core,
and the Snapdragon 8 Gen 1, their latest high-end phone SoC.
- Renesas adds support for R-Car S4-8, the most recent automotive
Server/Communication SoC.
- TI adds support for J721s2, a new automotive SoC in the K3
family.
- Mediatek MT7986a/b is a SoC used in Wifi routers, the latest
generation following their popular MT76xx series. Only basic
support is added for now.
- NXP i.MX8 ULP8 is a new low-power variant of the widespread
i.MX8 series.
- TI SPEAr320s is a minor variant of the old SPEAr320 SoC that
we have supported for a long time.
New boards with the existing SoCs include
- Aspeed AST2500/AST2600 BMCs in TYAN, Facebook and Yadro servers
- AT91/SAMA5 based evaluation board
- NXP gains twenty new development and industrial boards for their
i.MX and Layerscape SoCs
- Intel IXP4xx now supports the final two machines in device tree
that were previously only supported in old style board files.
- Mediatek MT6589 is used in the Fairphone FP1 phone from 2013,
while MT8183 is used in the Acer Chromebook 314.
- Qualcomm gains support for the reference machines using the two
new SoCs, plus a number of Chromebook variants and phones based
on the Snapdragon 7c, 845 and 888 SoCs, including various
Sony Xperia devices and the Microsoft Surface Duo 2.
- ST STM32 now supports the Engicam i.Core STM32MP1 carrier board.
- Tegra now boots various older Android devices based on 32-bit
chips out of the box, including a number of ASUS Transformer
tablets.
There is also a new Jetson AGX Orin developer kit.
- Apple support adds the missing device trees for all the remaining
M1 Macbook and iMac variants, though not yet the M1 Pro/Max
versions.
- Allwinner now supports another version of the Tanix TX6 set-top
box based on the H6 SoC.
- Broadcom gains support for the Netgear RAXE500 Wireless router
based on BCM4908.
-----BEGIN PGP SIGNATURE-----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=IF3G
-----END PGP SIGNATURE-----
Merge tag 'dt-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC devicetree updates from Arnd Bergmann:
"As usual, this is the bulk of the updates for the SoC tree, adding
more devices to existing files, addressing issues from ever improving
automated checking, and fixing minor issues.
The most interesting bits as usual are the new platforms. All the
newly supported SoCs belong into existing families this time:
- Qualcomm gets support for two newly announced platforms, both of
which can now work in production environments: the SDX65 5G modem
that can run a minimal Linux on its Cortex-A7 core, and the
Snapdragon 8 Gen 1, their latest high-end phone SoC.
- Renesas adds support for R-Car S4-8, the most recent automotive
Server/Communication SoC.
- TI adds support for J721s2, a new automotive SoC in the K3 family.
- Mediatek MT7986a/b is a SoC used in Wifi routers, the latest
generation following their popular MT76xx series. Only basic
support is added for now.
- NXP i.MX8 ULP8 is a new low-power variant of the widespread i.MX8
series.
- TI SPEAr320s is a minor variant of the old SPEAr320 SoC that we
have supported for a long time.
New boards with the existing SoCs include
- Aspeed AST2500/AST2600 BMCs in TYAN, Facebook and Yadro servers
- AT91/SAMA5 based evaluation board
- NXP gains twenty new development and industrial boards for their
i.MX and Layerscape SoCs
- Intel IXP4xx now supports the final two machines in device tree
that were previously only supported in old style board files.
- Mediatek MT6589 is used in the Fairphone FP1 phone from 2013, while
MT8183 is used in the Acer Chromebook 314.
- Qualcomm gains support for the reference machines using the two new
SoCs, plus a number of Chromebook variants and phones based on the
Snapdragon 7c, 845 and 888 SoCs, including various Sony Xperia
devices and the Microsoft Surface Duo 2.
- ST STM32 now supports the Engicam i.Core STM32MP1 carrier board.
- Tegra now boots various older Android devices based on 32-bit chips
out of the box, including a number of ASUS Transformer tablets.
There is also a new Jetson AGX Orin developer kit.
- Apple support adds the missing device trees for all the remaining
M1 Macbook and iMac variants, though not yet the M1 Pro/Max
versions.
- Allwinner now supports another version of the Tanix TX6 set-top box
based on the H6 SoC.
- Broadcom gains support for the Netgear RAXE500 Wireless router
based on BCM4908"
* tag 'dt-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (574 commits)
Revert "ARM: dts: BCM5301X: define RTL8365MB switch on Asus RT-AC88U"
arm64: dts: qcom: sm6125: Avoid using missing SM6125_VDDCX
arm64: dts: qcom: sm8450-qrd: Enable USB nodes
arm64: dts: qcom: sm8450: Add usb nodes
ARM: dts: aspeed: add LCLK setting into LPC KCS nodes
dt-bindings: ipmi: bt-bmc: add 'clocks' as a required property
ARM: dts: aspeed: add LCLK setting into LPC IBT node
ARM: dts: aspeed: p10: Add TPM device
ARM: dts: aspeed: p10: Enable USB host ports
ARM: dts: aspeed: Add TYAN S8036 BMC machine
ARM: dts: aspeed: tyan-s7106: Add uart_routing and fix vuart config
ARM: dts: aspeed: Adding Facebook Bletchley BMC
ARM: dts: aspeed: g220a: Enable secondary flash
ARM: dts: Add openbmc-flash-layout-64-alt.dtsi
ARM: dts: aspeed: Add secure boot controller node
dt-bindings: aspeed: Add Secure Boot Controller bindings
ARM: dts: Remove "spidev" nodes
dt-bindings: pinctrl: samsung: Add pin drive definitions for Exynos850
dt-bindings: arm: samsung: Document E850-96 board binding
dt-bindings: Add vendor prefix for WinLink
...
Tanix TX6 comes either with RTL8822BS or RTL8822CS wifi+bt combo module.
Wifi part is already enabled in tanix DTSI. Let's enable also bluetooth.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Both, Tanix TX6 and Tanix TX6 mini, have SDIO wifi module, albeit
different. However, driver can be autoprobed via SDIO ID.
Add MMC1 node, so kernel can discover wifi module and load driver for
it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tanix TX6 mini is less capable version of Tanix TX6 although it comes
with some features not present on Tanix TX6.
Basic specs:
- H6 SoC
- 2 GiB DDR3 RAM
- HDMI
- SPDIF
- 2x USB
- analogue audio
- CVBS
- SD card
- IR remote
- LED display
- fast ethernet
- XR819 wifi
- 16 GiB eMMC
Currently supported features doesn't differ that much from Tanix TX6,
but that will change soon.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
There is another very similar device to Tanix TX6, namely Tanix TX6
mini. Because most of the board design is shared, it makes sense to have
common nodes in DTSI file.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In order to support memory dynamic frequency scaling (MDFS), the MBUS
binding now requires enumerating more resources. Provide them in the
device tree.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211118031841.42315-6-samuel@sholland.org
In order to support memory dynamic frequency scaling (MDFS), the MBUS
binding now requires enumerating more resources. Provide them in the
device tree.
Since the H3 and H5 have different clock divider limits, they need
separate compatibles.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211118031841.42315-5-samuel@sholland.org
Experimentation determined that HDMI CEC controller inside DW HDMI block
depends on 32k clock from RTC. If this clock is tampered with, HDMI CEC
communication starts or stops working, depending on situation.
SoC user manual doesn't say anything about CEC, so this was overlooked.
Fix this by adding dependency to RTC 32k clock.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211120073448.32480-2-jernej.skrabec@gmail.com
Tanix TX6 has a LED display driven by FD650.
Currently there is no Linux driver nor any binding for it. However, we
can at least provide I2C node in DT, so user space scripts or programs
can manually control it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211121115002.693329-1-jernej.skrabec@gmail.com
Orange Pi Zero Plus uses a Realtek RTL8211E RGMII Gigabit PHY, but its
currently set to plain RGMII mode meaning that it doesn't introduce
delays.
With this setup, TX packets are completely lost and changing the mode to
RGMII-ID so the PHY will add delays internally fixes the issue.
Fixes: a7affb13b2 ("arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Ron Goossens <rgoossens@gmail.com>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211117140222.43692-1-robert.marko@sartura.hr
A new 'chassis-type' root node property has recently been approved for
the device-tree specification, in order to provide a simple way for
userspace to detect the device form factor and adjust their behavior
accordingly.
This patch fills in this property for end-user devices (such as laptops,
smartphones and tablets) based on Allwinner ARM64 processors.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211016102025.23346-2-arnaud.ferraris@collabora.com
This is a rather large update for the ARM devicetree files, after a few
quieter releases, with 775 total commits and 47 branches pulled into
this one. There are 5 new SoC types plus some minor variations, and
a total of 60 new machines, so I'm limiting the summary to the main
noteworthy items:
- Apple M1 gain support for PCI and pinctrl, getting a bit
closer to a usable system out of the box.
- Qualcomm gains support for Snapdragon 690 (aka SM6350) as
well as SM7225, 11 new smartphones, and three additional
Chromebooks, and improvements all over the place.
- Samsung gains support for ExynosAutov9, an automotive version
of their smartphone SoC, but otherwise no major changes.
- Microchip adds the SAMA5D29 SoC in the SAMA5 family, and a
number of improvements for the recently added SAMA7 family.
The LAN966 SoC that was added in the platform code does not
have dts files yet. Two board files are added for the older
at91sam9g20 SoC
- Aspeed supports two additional server boards using their AST2600
as BMC, and improves support for qemu models
- Rockchip RK3566/RK3688 gets added, along with six new
development boards using RK3328/RK3399/RK3566, and one
Chromebook tablet.
- Two NAS boxes are added using the ARMv4 based Gemini platform
- One new board is added to the Intel Arria SoC FPGA family
- Marvell adds one network switch based on Armada 381 and the
new MOCHAbin 7040 development board
- NXP adds support for the S32G2 automotive SoC, two imx6 based
ebook readers, and three additional development boards, which
is notably less than their usual additions, but they also gain
improvements to their many existing boards
- STmicroelectronics adds their stm32mp13 SoC family along with
a reference board
- Renesas adds new versions of their R-Car Gen3 SoCs and many
updates for their older generations
- Broadcom adds support for a number of Cisco Meraki wireless
controllers, along with two new boards and other updates for
BCM53xx/BCM47xx networking SoCs and the Raspberry Pi
boards
- Mediatek improves support for the MT81xx SoCs used in Chromebooks
as well as the MT76xx networking SoCs
- NVIDIA adds a number of cleanups and additional support for
more hardware on the already supported machines
- TI K3 adds support for three new boards along with cleanups
- Toshiba adds one board for the Visconti family
- Xilinx adds five new ZynqMP based machines
- Amlogic support is added for the Radxa Zero and two Jethub
home automation controllers, along with changes to other
machines
- Rob Herring continues his work on fixing dtc warnings all over
the tree.
- Minor updates for TI OMAP, Mstar, Allwinner/sunxi, Hisilicon,
Ux500, Unisoc
-----BEGIN PGP SIGNATURE-----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=jp4P
-----END PGP SIGNATURE-----
Merge tag 'dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC DT updates from Arnd Bergmann:
"This is a rather large update for the ARM devicetree files, after a
few quieter releases, with 775 total commits and 47 branches pulled
into this one.
There are 5 new SoC types plus some minor variations, and a total of
60 new machines, so I'm limiting the summary to the main noteworthy
items:
- Apple M1 gain support for PCI and pinctrl, getting a bit closer to
a usable system out of the box.
- Qualcomm gains support for Snapdragon 690 (aka SM6350) as well as
SM7225, 11 new smartphones, and three additional Chromebooks, and
improvements all over the place.
- Samsung gains support for ExynosAutov9, an automotive version of
their smartphone SoC, but otherwise no major changes.
- Microchip adds the SAMA5D29 SoC in the SAMA5 family, and a number
of improvements for the recently added SAMA7 family. The LAN966 SoC
that was added in the platform code does not have dts files yet.
Two board files are added for the older at91sam9g20 SoC
- Aspeed supports two additional server boards using their AST2600 as
BMC, and improves support for qemu models
- Rockchip RK3566/RK3688 gets added, along with six new development
boards using RK3328/RK3399/RK3566, and one Chromebook tablet.
- Two NAS boxes are added using the ARMv4 based Gemini platform
- One new board is added to the Intel Arria SoC FPGA family
- Marvell adds one network switch based on Armada 381 and the new
MOCHAbin 7040 development board
- NXP adds support for the S32G2 automotive SoC, two imx6 based ebook
readers, and three additional development boards, which is notably
less than their usual additions, but they also gain improvements to
their many existing boards
- STmicroelectronics adds their stm32mp13 SoC family along with a
reference board
- Renesas adds new versions of their R-Car Gen3 SoCs and many updates
for their older generations
- Broadcom adds support for a number of Cisco Meraki wireless
controllers, along with two new boards and other updates for
BCM53xx/BCM47xx networking SoCs and the Raspberry Pi boards
- Mediatek improves support for the MT81xx SoCs used in Chromebooks
as well as the MT76xx networking SoCs
- NVIDIA adds a number of cleanups and additional support for more
hardware on the already supported machines
- TI K3 adds support for three new boards along with cleanups
- Toshiba adds one board for the Visconti family
- Xilinx adds five new ZynqMP based machines
- Amlogic support is added for the Radxa Zero and two Jethub home
automation controllers, along with changes to other machines
- Rob Herring continues his work on fixing dtc warnings all over the
tree.
- Minor updates for TI OMAP, Mstar, Allwinner/sunxi, Hisilicon,
Ux500, Unisoc"
* tag 'dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (720 commits)
arm64: dts: apple: j274: Expose PCI node for the Ethernet MAC address
arm64: dts: apple: t8103: Add root port interrupt routing
arm64: dts: apple: t8103: Add PCIe DARTs
arm64: apple: Add PCIe node
arm64: apple: Add pinctrl nodes
ARM: dts: arm: Update ICST clock nodes 'reg' and node names
ARM: dts: arm: Update register-bit-led nodes 'reg' and node names
arm64: dts: exynos: add chipid node for exynosautov9 SoC
ARM: dts: qcom: fix typo in IPQ8064 thermal-sensor node
Revert "arm64: dts: qcom: msm8916-asus-z00l: Add sensors"
arm64: dts: qcom: ipq6018: Remove unused 'iface_clk' property from dma-controller node
arm64: dts: qcom: ipq6018: Remove unused 'qcom,config-pipe-trust-reg' property
arm64: dts: qcom: sm8350: Add CPU topology and idle-states
arm64: dts: qcom: Drop unneeded extra device-specific includes
arm64: dts: qcom: msm8916: Drop standalone smem node
arm64: dts: qcom: Fix node name of rpm-msg-ram device nodes
arm64: dts: qcom: msm8916-asus-z00l: Add sensors
arm64: dts: qcom: msm8916-asus-z00l: Add SDCard
arm64: dts: qcom: msm8916-asus-z00l: Add touchscreen
arm64: dts: qcom: sdm845-oneplus: remove devinfo-size from ramoops node
...
