All Allwinner H616/H618 SoCs contain a Mali G31 MP2 GPU.
Enable the DT nodes for that GPU, and specify the regulator providing
power to the VDD_GPU pins of the package. The rest of the DT node is set
by the SoC, so is not board specific.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20250416224839.9840-5-andre.przywara@arm.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Now that the H616 (and variants) audio codec is supported, enable it for
boards with a mainline DTS. The Tanix TX1, Transpeed 8K618-T and X-96
Mate have all been tested with the onboard 3.5mm audio jack and the
Orange Pi Zero 3 with a 3.5mm jack connected to the audio header.
The RG35XX (2024, -H, -Plus and -SP variants) are also tested working
but have a separate mux and GPIO-controlled (PI5) power amplifier to
support both a headphone jack and onboard speakers.
The headphone jack has a GPIO for jack detection, but this is not
currently supported by the driver, so audio is heard both via the
headphone jack and speakers when the speaker amp is powered (by the
CLDO1 regulator, defined as always-on until proper jack detection is
implemented).
Define the audio codec and routing for all supported H616 and variant
boards, and power and speaker amp enablement where present on boards and
known.
Signed-off-by: Ryan Walklin <ryan@testtoast.com>
Tested-by: Philippe Simons <simons.philippe@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Link: https://patch.msgid.link/20241023075917.186835-8-ryan@testtoast.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
With the DT bindings now describing the format of the CPU OPP tables, we
can include the OPP table in each board's .dts file, and specify the CPU
power supply.
This allows to enable DVFS, and get up to 50% of performance benefit in
the highest OPP, or up to 60% power savings in the lowest OPP, compared
to the fixed 1GHz @ 1.0V OPP we are running in by default at the moment.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The Orange Pi Zero 2W is a board based on the Allwinner H618 SoC.
It uses the RaspberryPi Zero form factor, with an optional expansion
board, connected via an FPC connector, to provide more connectors.
The base board features:
- Allwinner H618 SoC (quad Cortex-A53 cores, with 1MB L2 cache)
- 1, 2 or 4GB of LPDDR4 DRAM
- SD card socket
- two USB-C sockets, one UFP, one DFP
- HDMI connector
- (yet unsupported) WiFi module
- 16 MiB SPI flash
- power supply via the UFP USB-C port
The FPC connector provides access to two more USB host ports, Fast
Ethernet, some GPIOs, Audio Line out and the IR receiver pin.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20231020145706.705420-3-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
