'clock-latency-ns' is not a valid property for CPU nodes. It belongs in
OPP table (which has it). Drop them from the CPU nodes.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20250410-dt-cpu-schema-v2-1-63d7dc9ddd0a@kernel.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add missing cache information to the Allwinner H6 SoC dtsi, to allow
the userspace, which includes lscpu(1) that uses the virtual files provided
by the kernel under the /sys/devices/system/cpu directory, to display the
proper H6 cache information.
Adding the cache information to the H6 SoC dtsi also makes the following
warning message in the kernel log go away:
cacheinfo: Unable to detect cache hierarchy for CPU 0
The cache parameters for the H6 dtsi were obtained and partially derived
by hand from the cache size and layout specifications found in the following
datasheets and technical reference manuals:
- Allwinner H6 V200 datasheet, version 1.1
- ARM Cortex-A53 revision r0p3 TRM, version E
For future reference, here's a brief summary of the documentation:
- All caches employ the 64-byte cache line length
- Each Cortex-A53 core has 32 KB of L1 2-way, set-associative instruction
cache and 32 KB of L1 4-way, set-associative data cache
- The entire SoC has 512 KB of unified L2 16-way, set-associative cache
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/49abb93000078c692c48c0a65ff677893909361a.1714304071.git.dsimic@manjaro.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Underscores should not be used in node names (dtc with W=2 warns about
them), so replace them with hyphens. Use also generic name for pwrseq
node, because generic naming is favored by Devicetree spec. All the
clocks affected by this change use clock-output-names, so resulting
clock name should not change. Functional impact checked with comparing
before/after DTBs with dtx_diff and fdtdump.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240317184130.157695-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The SPDIF hardware found on the H6 supports both transmit and receive
functions. However it is missing the RX DMA channel.
Add the SPDIF hardware block's RX DMA channel. Also remove the
by-default pinmux, since the end device can choose to implement
either or both functionalities.
Fixes: f95b598df4 ("arm64: dts: allwinner: Add SPDIF node for Allwinner H6")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240127163247.384439-6-wens@kernel.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The Hantro G2 video decoder block sits behind the IOMMU. Without a
reference for the system to properly configure the IOMMU, it will fault
and cause the video decoder to fail.
Add a proper reference to the IOMMU port. The master ID is taken from
the IOMMU fault error message on Linux, and the number seems to match
the order in the user manual's IOMMU diagram.
Fixes: 0baddea60e ("arm64: dts: allwinner: h6: Add Hantro G2 node")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221115090644.3602573-3-wenst@chromium.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Add a simple cooling map for the GPU.
This cooling map come from the vendor kernel 4.9 with a
2°C hysteresis added.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220906153034.153321-3-peron.clem@gmail.com
The binding header provides descriptive names for the RTC clock indexes,
since the indexes were arbitrarily chosen by the binding, not by the
hardware. Let's use the names, so the meaning is clearer.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220607012438.18183-2-samuel@sholland.org
While it doesn't really matter from a functional point of view in this
driver's case, it's usually a good practice to list the clocks in a
driver in the same driver across all its users.
The H6 is using the inverse order than all the other users, so let's
make it consistent.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-49-maxime@cerno.tech
For a CPU to enter an idle state, some timer must be available to
trigger an IRQ and wake it back up. The local ARM architectural timer is
not sufficient, because that timer stops when the CPU is powered down.
The ARM architectural timer from some other CPU can be used, but doing
so prevents that other CPU from entering an idle state. For all CPUs to
power down at the same time, Linux needs a timer which is not tied to
any CPU.
Hook up the "sun4i" timer so it can be used for this purpose. It runs at
24 MHz, which balances resolution and power consumption.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210322044707.19479-5-samuel@sholland.org
There are six new SoCs added this time. Apple M1 and Nuvoton WPCM450
have separate branches because they are new SoC families that require
changes outside of device tree files. The other four are variations of
already supported chips and get merged through this branch:
- STMicroelectronics STM32H750 is one of many variants of STM32
microcontrollers based on the Cortex-M7 core. This is particularly
notable since we rarely add support for new MMU-less chips
these days. In this case, the board that gets added along with
the platform is not a SoC reference platform but the "Art Pi"
(https://art-pi.gitee.io/website/) machine that was originally design
for the RT-Thread RTOS.
- NXP i.MX8QuadMax is a variant of the growing i.MX8 embedded/industrial
SoC family, using two Cortex-A72 and four Cortex-A53 cores. It
gets added along with its reference board, the "NXP i.MX8QuadMax
Multisensory Enablement Kit".
- Qualcomm SC7280 is a Laptop SoC following the SC7180 (Snapdragon 7c)
that is used in some Chromebooks and Windows laptops. Only a reference
board is added for the moment.
- TI AM64x Sita4ra is a new version of the K3 SoC family for industrial
control, motor control, remote IO, IoT gateway etc., similar to the
older AM65x family. Two reference machines are added alongside.
Among the newly added machines, there is a very clear skew towards 64-bit
machines now, with 12 32-bit machines compared to 23 64-bit machines. The
full list sorted by SoC is:
- ASpeed AST2500 BMC: ASRock E3C246D4I Xeon server board
- Allwinner A10: Topwise A721 Tablet
- Amlogic GXL: MeCool KII TV box
- Amlogic GXM: Mecool KIII, Minix Neo U9-H TV boxes
- Broadcom BCM4908: TP-Link Archer C2300 V1 router
- MStar SSD202D: M5Stack UnitV2 camera
- Marvell Armada 38x: ATL-x530 ethernet switch
- Mediatek MT8183 Chromebooks: Lenovo 10e, Acer Spin 311,
Asus Flip CM3, Asus Detachable CM3
- Mediatek MT8516/MT8183: OLogic Pumpkin Board
- NXP i.MX7: reMarkable Tablet
- NXP i.MX8M: Kontron pitx-imx8m, Engicam i.Core MX8M Mini
- Nuvoton NPCM730: Quanta GBS BMC
- Qualcomm X55: Telit FN980 TLB SoM, Thundercomm TurboX T55 SoM
- Qualcomm MSM8998: OnePlus 5/5T phones
- Qualcomm SM8350: Snapdragon 888 Mobile Hardware Development Kit
- Rockchip RK3399: NanoPi R4S board
- STM32MP1: Engicam MicroGEA STM32MP1 MicroDev 2.0 and SOM,
EDIMM2.2 Starter Kit, Carrier, SOM
- TI AM65: Siemens SIMATIC IOT2050 gateway
There is notable work going into extending already supported machines
and SoCs:
- ASpeed AST2500
- Allwinner A23, A83t, A31, A64, H6
- Amlogic G12B
- Broadcom BCM4908
- Marvell Armada 7K/8K/CN91xx
- Mediatek MT6589, MT7622, MT8173, MT8183, MT8195
- NXP i.MX8Q, i.MX8MM, i.MX8MP
- Qualcomm MSM8916, SC7180, SDM845, SDX55, SM8350
- Renesas R-Car M3, V3U
- Rockchip RK3328, RK3399
- STEricsson U8500
- STMicroelectronics STM32MP141
- Samsung Exynos 4412
- TI K3-AM65, K3-J7200
- TI OMAP3
Among the treewide cleanups and bug fixes, two parts stand out:
- There are a number of cleanups for issues pointed out by 'make
dtbs_check' this time, and I expect more to come in the future as we
increasingly check for regressions.
- After a change to the MMC subsystem that can lead to unpredictable
device numbers, several platforms add 'aliases' properties for these
to give each MMC controller a fixed number.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=SpTo
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"There are six new SoCs added this time.
Apple M1 and Nuvoton WPCM450 have separate branches because they are
new SoC families that require changes outside of device tree files.
The other four are variations of already supported chips and get
merged through this branch:
- STMicroelectronics STM32H750 is one of many variants of STM32
microcontrollers based on the Cortex-M7 core.
This is particularly notable since we rarely add support for new
MMU-less chips these days. In this case, the board that gets added
along with the platform is not a SoC reference platform but the
"Art Pi" (https://art-pi.gitee.io/website/) machine that was
originally design for the RT-Thread RTOS.
- NXP i.MX8QuadMax is a variant of the growing i.MX8
embedded/industrial SoC family, using two Cortex-A72 and four
Cortex-A53 cores.
It gets added along with its reference board, the "NXP i.MX8QuadMax
Multisensory Enablement Kit".
- Qualcomm SC7280 is a Laptop SoC following the SC7180 (Snapdragon
7c) that is used in some Chromebooks and Windows laptops.
Only a reference board is added for the moment.
- TI AM64x Sita4ra is a new version of the K3 SoC family for
industrial control, motor control, remote IO, IoT gateway etc.,
similar to the older AM65x family.
Two reference machines are added alongside.
Among the newly added machines, there is a very clear skew towards
64-bit machines now, with 12 32-bit machines compared to 23 64-bit
machines. The full list sorted by SoC is:
- ASpeed AST2500 BMC: ASRock E3C246D4I Xeon server board
- Allwinner A10: Topwise A721 Tablet
- Amlogic GXL: MeCool KII TV box
- Amlogic GXM: Mecool KIII, Minix Neo U9-H TV boxes
- Broadcom BCM4908: TP-Link Archer C2300 V1 router
- MStar SSD202D: M5Stack UnitV2 camera
- Marvell Armada 38x: ATL-x530 ethernet switch
- Mediatek MT8183 Chromebooks: Lenovo 10e, Acer Spin 311, Asus Flip
CM3, Asus Detachable CM3
- Mediatek MT8516/MT8183: OLogic Pumpkin Board
- NXP i.MX7: reMarkable Tablet
- NXP i.MX8M: Kontron pitx-imx8m, Engicam i.Core MX8M Mini
- Nuvoton NPCM730: Quanta GBS BMC
- Qualcomm X55: Telit FN980 TLB SoM, Thundercomm TurboX T55 SoM
- Qualcomm MSM8998: OnePlus 5/5T phones
- Qualcomm SM8350: Snapdragon 888 Mobile Hardware Development Kit
- Rockchip RK3399: NanoPi R4S board
- STM32MP1: Engicam MicroGEA STM32MP1 MicroDev 2.0 and SOM, EDIMM2.2
Starter Kit, Carrier, SOM
- TI AM65: Siemens SIMATIC IOT2050 gateway
There is notable work going into extending already supported machines
and SoCs:
- ASpeed AST2500
- Allwinner A23, A83t, A31, A64, H6
- Amlogic G12B
- Broadcom BCM4908
- Marvell Armada 7K/8K/CN91xx
- Mediatek MT6589, MT7622, MT8173, MT8183, MT8195
- NXP i.MX8Q, i.MX8MM, i.MX8MP
- Qualcomm MSM8916, SC7180, SDM845, SDX55, SM8350
- Renesas R-Car M3, V3U
- Rockchip RK3328, RK3399
- STEricsson U8500
- STMicroelectronics STM32MP141
- Samsung Exynos 4412
- TI K3-AM65, K3-J7200
- TI OMAP3
Among the treewide cleanups and bug fixes, two parts stand out:
- There are a number of cleanups for issues pointed out by 'make
dtbs_check' this time, and I expect more to come in the future as
we increasingly check for regressions.
- After a change to the MMC subsystem that can lead to unpredictable
device numbers, several platforms add 'aliases' properties for
these to give each MMC controller a fixed number"
* tag 'arm-dt-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (516 commits)
dt-bindings: mali-bifrost: add dma-coherent
arm64: dts: amlogic: misc DT schema fixups
arm64: dts: qcom: sc7180: Update iommu property for simultaneous playback
arm64: dts: qcom: sc7180: pompom: Add "dmic_clk_en" + sound model
arm64: dts: qcom: sc7180: coachz: Add "dmic_clk_en"
ARM: dts: mstar: Add a dts for M5Stack UnitV2
dt-bindings: arm: mstar: Add compatible for M5Stack UnitV2
dt-bindings: vendor-prefixes: Add vendor prefix for M5Stack
arm64: dts: mt8183: fix dtbs_check warning
arm64: dts: mt8183-pumpkin: fix dtbs_check warning
ARM: dts: aspeed: tiogapass: add hotplug controller
ARM: dts: aspeed: amd-ethanolx: Enable all used I2C busses
ARM: dts: aspeed: Rainier: Update to pass 2 hardware
ARM: dts: aspeed: Rainier 1S4U: Fix fan nodes
ARM: dts: aspeed: Rainier: Fix humidity sensor bus address
ARM: dts: aspeed: Rainier: Fix PCA9552 on bus 8
ARM: dts: qcom: sdx55: add IPA information
ARM: dts: qcom: sdx55: Add basic devicetree support for Thundercomm T55
dt-bindings: arm: qcom: Add binding for Thundercomm T55 kit
ARM: dts: qcom: sdx55: Add basic devicetree support for Telit FN980 TLB
...
The macros for the clock and reset indices for the RSB hardware block
were replaced with raw numbers when the RSB controller node was added.
This was done to avoid cross-tree dependencies.
Now that both the clk and DT changes have been merged, we can switch
back to using the macros.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
All IRQs that can be used to wake up the system must be routed through
r_intc, so they are visible to firmware while the system is suspended.
In addition to the external NMI input, which is already routed through
r_intc, these include PIO and R_PIO (gpio-keys), the LRADC, and the RTC.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The binding of R_INTC was updated to allow specifying interrupts other
than the external NMI, since routing those interrupts through the R_INTC
driver allows using them for wakeup.
Update the device trees to use the new binding.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The H6 SoC contains an undocumented but fully functional RSB controller.
Add support for it. The MMIO register address matches other SoCs of the
same generation, and the IRQ matches a hole in the documented IRQ list.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
[wens@csie.org: Use raw numbers instead of macros for clock/reset index]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The H6 manual explicitly lists a frequency limit of 150 MHz for the bus
frequency of the MMC controllers. So far we had no explicit limits in the
DT, which limited eMMC to the spec defined frequencies, or whatever the
driver defines (both Linux and FreeBSD use 52 MHz here).
Put those maximum frequencies in the SoC .dtsi, to allow higher speed
modes (which still would need to be explicitly enabled, per board).
Tested with an eMMC using HS-200 on a Pine H64. Running at the spec'ed
200 MHz indeed fails with I/O errors, but 150 MHz seems to work stably.
Fixes: 8f54bd1595 ("arm64: allwinner: h6: add device tree nodes for MMC controllers")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-6-andre.przywara@arm.com
In recent Allwinner SoCs the first USB host controller (HCI0) shares
the first PHY with the MUSB controller. Probably to make this sharing
work, we were avoiding to declare this in the DT. This has two
shortcomings:
- U-Boot (which uses the same .dts) cannot use this port in host mode
without a PHY linked, so we were loosing one USB port there.
- It requires the MUSB driver to be enabled and loaded, although we
don't actually use it.
To avoid those issues, let's add this PHY link to the H6 .dtsi file.
After all PHY port 0 *is* connected to HCI0, so we should describe
it as this.
This makes it work in U-Boot, also improves compatiblity when no MUSB
driver is loaded (for instance in distribution installers).
Fixes: eabb3d424b ("arm64: dts: allwinner: h6: add USB2-related device nodes")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-3-andre.przywara@arm.com
In accordance with the DWC USB3 bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "snps,dwc3"-compatible nodes are correctly
named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201020115959.2658-25-Sergey.Semin@baikalelectronics.ru
When possible, system firmware on 64-bit Allwinner platforms disables
OSC24M during system suspend. Since this oscillator is the clock source
for the ARM architectural timer, this causes the timer to stop counting.
Therefore, the ARM architectural timer must not be marked as NONSTOP on
these platforms, or the time will be wrong after system resume.
Adding the arm,no-tick-in-suspend property forces the kernel to ignore
the ARM architectural timer when calculating sleeptime; it falls back to
reading the RTC. Note that this only affects deep suspend, not s2idle.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200809021822.5285-1-samuel@sholland.org
Now that the IOMMU driver has been introduced, it prevents any access from
a DMA master going through it that hasn't properly mapped the pages, and
that link is set up through the iommus property.
Unfortunately we forgot to add that property to the video engine node when
adding the IOMMU node, so now any DMA access is broken.
Fixes: b3a0a2f910 ("arm64: dts: allwinner: h6: Add IOMMU")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200628180804.79026-1-maxime@cerno.tech
Add an Operating Performance Points table for the CPU cores to
enable Dynamic Voltage & Frequency Scaling on the H6.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This enables passive cooling by down-regulating CPU voltage
and frequency.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The ARM CPU cores are fed by the CPU clock from the CCU. Add a
reference to the clock for each CPU core, along with the clock
transition latency.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The H6 SoC contains a message box that can be used to send messages and
interrupts back and forth between the ARM application CPUs and the ARISC
coprocessor. Add a device tree node for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
It turns out that not all H6 boards have external 32kHz oscillator.
Currently the only one known such H6 board is Tanix TX6.
Move external oscillator node from common H6 dtsi to board specific dts
files where present.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The commit 7aa9b9eb7d ("arm64: dts: allwinner: H6: Add PMU mode")
introduced support for the PMU found on the Allwinner H6. However, the
binding only allows for a single compatible, while the patch was adding
two.
Make sure we follow the binding.
Fixes: 7aa9b9eb7d ("arm64: dts: allwinner: H6: Add PMU mode")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The Allwinner H6 SoC contains two SPI controllers similar to the H3/A64,
but with the added capability of 3-wire and 4-wire operation modes.
For now the driver does not support those, but the SPI registers are
fully backwards-compatible, just adding bits and registers which were
formerly reserved. So we can use the existing driver in "legacy" SPI
modes, for instance to access the SPI NOR flash soldered on the PineH64
board.
We use an H6 specific compatible string in addition to the existing H3
string, so when the driver later gains QSPI support, it should work
automatically without any DT changes.
Tested by accessing the SPI flash on a Pine H64 board (SPI0), also
connecting another SPI flash to the SPI1 header pins.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
There are two sensors, one for CPU, one for GPU.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Allwinner device tree files used different comment style for
copyright notice.
Update this to keep a coherency.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
With dual licensed SPDX identifier the "OR" should
be uppercase.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Allwinner H6 PWM is similar to that in A20 except that it has additional
bus clock and reset line.
Note that first PWM channel is connected to output pin and second
channel is used internally, as a clock source to AC200 co-packaged chip.
This means that any combination of these two channels can be used and
thus it doesn't make sense to add pinctrl nodes at this point.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Add the Performance Monitoring Unit (PMU) device tree node to the H6
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core. The numbers come from the manual and have
been checked in U-Boot and with perf in Linux.
Tested with perf record and taskset on a Pine H64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Allwinner H6 SoC features USB3 functionality, with a DWC3 controller and
a custom PHY.
Add device tree nodes for them.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The Crypto Engine is a hardware cryptographic accelerator that supports
many algorithms.
This patch enables the Crypto Engine on the Allwinner H6 SoC Device-tree.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Orange Pi 3 uses UART1 for bluetooth. Add pinconfigs so that we can use
them.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
This reverts commits 3d109bdca9 ("ARM: dts: sunxi: Remove useless
phy-names from EHCI and OHCI"), 0a3df8bb6d ("ARM: dts: sunxi: h3/h5:
Remove useless phy-names from EHCI and OHCI") and 3c7ab90aaa ("arm64:
dts: allwinner: Remove useless phy-names from EHCI and OHCI").
It turns out that while the USB bindings were not mentionning it, the PHY
client bindings were mandating that phy-names is set when phys is. Let's
add it back.
Fixes: 3d109bdca9 ("ARM: dts: sunxi: Remove useless phy-names from EHCI and OHCI")
Fixes: 0a3df8bb6d ("ARM: dts: sunxi: h3/h5: Remove useless phy-names from EHCI and OHCI")
Fixes: 3c7ab90aaa ("arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191002112651.100504-1-mripard@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The watchdog has a clock on all our SoCs, but it wasn't always listed.
Add it to the devicetree where it's missing.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This patch adds RTC node and fixes the clock properties and nodes
to reflect the real clock tree.
The device nodes for the internal oscillator and osc32k are removed,
as these clocks are now provided by the RTC device. Clock references
are fixed accordingly, too.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add device-tree nodes for i2c0 to i2c2, and also add relevant pinctrl
nodes.
Suggested-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner H6 has a SPDIF controller called OWA (One Wire Audio).
Only one pinmuxing is available so set it as default.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 IR is similar to A31 and can use same driver.
Add support for it.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Even though the binding mentions that the PHY name must be "phy", it turns
out that all our DTs had "hdmi-phy" instead.
The code doesn't care about the phy-names property, so we can just change
our DTs to match the binding, without any side effect.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The SID node one the H6 doesn't have a standard node name. Switch to the
one we use for the other SoCs.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
H6 has DMA controller which supports 16 channels.
Add a node for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 has a r_watchdog similar to A64.
Declare it in the device-tree.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
