Tanix TX6 comes either with RTL8822BS or RTL8822CS wifi+bt combo module.
Wifi part is already enabled in tanix DTSI. Let's enable also bluetooth.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
There is another very similar device to Tanix TX6, namely Tanix TX6
mini. Because most of the board design is shared, it makes sense to have
common nodes in DTSI file.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tanix TX6 has a LED display driven by FD650.
Currently there is no Linux driver nor any binding for it. However, we
can at least provide I2C node in DT, so user space scripts or programs
can manually control it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211121115002.693329-1-jernej.skrabec@gmail.com
While there is no publicly available schematic of this board, it's not
hard to determine voltage of GPIO port C, D and G (only ones which can
be set).
Port C and G are used for MMC/SDIO communication, so they use 1.8 V
power supply. It's not clear if port D is even used, but if it is, it's
pretty safe to assume it uses 3.3 V power supply. Value read from PIO
Group Withstand Voltage Mode Select register from within pre-installed
Android agrees with that assesment.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210722161220.51181-3-jernej.skrabec@gmail.com
Enable CPU opp tables for Tanix TX6.
Also add the fixed regulator that provided vdd-cpu-gpu required for
CPU opp tables.
This voltage has been found using a voltmeter and could be wrong.
Tested-by: Jernej Škrabec <jernej.skrabec@gmail.com>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Allwinner device tree files used different comment style for
copyright notice.
Update this to keep a coherency.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
With dual licensed SPDX identifier the "OR" should
be uppercase.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tanix TX6 box comes with a remote. Add a mapping for it.
Suggested-by: Michael Lange <linuxstuff@milaw.biz>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Enable USB 3.0 phy and host controller.
VBUS is directly connected to DCIN 5V and doesn't
require to be switched on.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Unlike other H6 boards, Tanix TX6 doesn't have a PMIC so we can enable
the GPU without providing a specific power supply.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tanix TX6 is an Allwinner H6 based TV box, which supports:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 4GiB DDR3 RAM (3GiB useable)
- 100Mbps EMAC via AC200 EPHY
- Cdtech 47822BS Wifi/BT
- 2x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- IR receiver
- 64GiB eMMC
- 5V/2A DC power supply
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
