Underscores should not be used in node names (dtc with W=2 warns about
them), so replace them with hyphens. Use also generic name for pwrseq
node, because generic naming is favored by Devicetree spec. All the
clocks affected by this change use clock-output-names, so resulting
clock name should not change. Functional impact checked with comparing
before/after DTBs with dtx_diff and fdtdump.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240317184130.157695-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
A new 'chassis-type' root node property has recently been approved for
the device-tree specification, in order to provide a simple way for
userspace to detect the device form factor and adjust their behavior
accordingly.
This patch fills in this property for end-user devices (such as laptops,
smartphones and tablets) based on Allwinner ARM64 processors.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211016102025.23346-2-arnaud.ferraris@collabora.com
This patch enables HDMI display on PINE64 PineTab.
The PineTab has a HDMI Type C (mini) port.
Signed-off-by: Dang Huynh <danct12@disroot.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210914193732.3047668-1-danct12@disroot.org
The fixed regulator clock name has a unit address, but no reg property,
which generates a warning in DTC. Change its name to remove its useless
unit address.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-51-maxime@cerno.tech
The binding of R_INTC was updated to allow specifying interrupts other
than the external NMI, since routing those interrupts through the R_INTC
driver allows using them for wakeup.
Update the device trees to use the new binding.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
As the original PineTab DT (which uses sun50i-a64-pinetab name) is only
for development samples, document this.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201224024138.19422-1-icenowy@aosc.io
make dtbs_check warm about unknown address/size-cells property in the
pinetab device-tree.
This is because these information are not necessary.
Drop them.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201011211514.155266-1-peron.clem@gmail.com
The sun8i-codec driver introduced a new set of DAPM widgets that more
accurately describe the hardware topology. Update the various device
trees to use the new widget names.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200726012557.38282-7-samuel@sholland.org
An older version of the analog codec binding referenced the headphone
amplifier binding as "hpvcc". However, by the time it was merged in
commit 21dd30200e ("ASoC: dt-bindings: sun50i-codec-analog: Add
headphone amp regulator supply"), the regulator reference was renamed to
"cpvdd". This board's device tree still uses the old name, which fails
to work at runtime, and which causes a warning from `make dtbs_check`.
Resolve both by fixing the name.
Fixes: 674ef1d0a7 ("arm64: dts: allwinner: a64: add support for PineTab")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
PineTab is a 10.1" tablet by Pine64 with Allwinner A64 inside.
It includes the following peripherals:
USB:
- A microUSB Type-B port connected to the OTG-capable USB PHY of
Allwinner A64. The ID pin is connected to a GPIO of the A64 SoC, and the
Vbus is connected to the Vbus of AXP803 PMIC. These enables OTG
functionality on this port.
- A USB Type-A port is connected to the internal hub attached to the
non-OTG USB PHY of Allwinner A64.
- There are reserved pins for an external keyboard connected to the
internal hub.
Power:
- The microUSB port has its Vbus connected to AXP803, mentioned above.
- A DC jack (of a strange size, 2.5mm outer diameter) is connected to
the ACIN of AXP803.
- A Li-Polymer battery is connected to the battery pins of AXP803.
Storage:
- An tradition Pine64 eMMC slot is on the board, mounted with an eMMC
module by factory.
- An external microSD slot is hidden under a protect case.
Display:
- A MIPI-DSI LCD panel (800x1280) is connected to the DSI port of A64 SoC.
- A mini HDMI port.
Input:
- A touch panel attached to a Goodix GT9271 touch controller.
- Volume keys connected to the LRADC of the A64 SoC.
Camera:
- An OV5640 CMOS camera is at rear, connected to the CSI bus of A64 SoC.
- A GC2145 CMOS camera is at front, shares the same CSI bus with OV5640.
Audio:
- A headphone jack is conencted to the SoC's internal codec.
- A speaker connected is to the Line Out port of SoC's internal codec, via
an amplifier.
Misc:
- Debug UART is muxed with the headphone jack, with the switch next to
the microSD slot.
- A bosch BMA223 accelerometer is connected to the I2C bus of A64 SoC.
- Wi-Fi and Bluetooth are available via a RTL8723CS chip, similar to the
one in Pinebook.
This commit adds a basically usable device tree for it, implementing
most of the features mentioned above. HDMI is not supported now because
bad LCD-HDMI coexistence situation of mainline A64 display driver, the
front camera currently lacks a driver and a facility to share the bus
with the rear one, and the accelerometer currently lacks a DT binding.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
