The OrangePi 4A is a typical Raspberry Pi model B sized development
board from Xunlong designed around an Allwinner T527 SoC.
The board has the following features:
- Allwinner T527 SoC
- AXP717B + AXP323 PMICs
- Up to 4GB LPDDR4 DRAM
- micro SD slot
- optional eMMC module
- M.2 slot for PCIe 2.0 x1
- 16 MB SPI-NOR flash
- 4x USB 2.0 type-A ports (one can be used in gadget mode)
- 1x Gigabit ethernet w/ Motorcomm PHY (through yet to be supported GMAC200)
- 3.5mm audio jack via internal audio codec
- HDMI 2.0 output
- eDP, MIPI CSI (2-lane and 4-lane) and MIPI DSI (4-lane) connectors
- USB type-C port purely for power
- AP6256 (Broadcom BCM4345) WiFi 5.0 + BT 5.0
- unsoldered headers for ADC and an additional USB 2.0 host port
- 40-pin GPIO header
Add a device tree for it, enabling all peripherals currently supported.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://patch.msgid.link/20250628161608.3072968-6-wens@kernel.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The H-A133L board is an industrial development board made by Liontron.
It contains a number of dedicated JST connectors, to connect external
peripherals. It features:
- Allwinner A133 SoC (4 * Arm Cortex-A53 cores at up to 1.6 GHz)
- 1 GiB, 2 GiB or 4 GiB of LPDDR4 DRAM
- between 16 and 128 GiB eMMC flash
- AXP707 PMIC (compatible to AXP803)
- 100 Mbit/s RJ45 Ethernet socket, using an JLSemi JL1101 PHY
- XR829 WIFI+Bluetooth chip
- 2 * USB 2.0 USB-A ports, plus three sets of USB pins on connectors
(connected via a USB hub connected to USB1 on the SoC)
- microSD card slot
- 3.5mm A/V port
- 12V power supply
- connectors for an LVDS or MIPI-DSI panel
Add the devicetree describing the board's peripherals and their
connections.
Despite being a devboard, the manufacturer does not publish a schematic
(I asked), so the PMIC rail assignments were bases on BSP dumps,
educated guesses and some experimentation. Dropping the always-on
property from any of the rails carrying it will make the board hang as
soon as the kernel turns off unused regulators.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Link: https://patch.msgid.link/20250505164729.18175-4-andre.przywara@arm.com
[wens@csie.org: fix property in &usbphy; fix comment typo in &usb_otg]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Chameleon board is an OpenHardware devboard made by YuzukiTsuru.
The form factor resembles the Raspberry Pi Model A boards, though it
differs significantly in its features:
- Allwinner H618 SoC (4 * Arm Cortex-A53 cores, 1MB L2 cache, 1.4 GHz)
- between 512MiB and 2GiB DDR3 DRAM
- up to 128 GiB eMMC flash
- AXP313a PMIC
- 100 Mbit/s Ethernet pins on a header
- XR829 WIFI+Bluetooth chip
- 4 * USB 2.0 USB-C ports
- microSD card slot
- 3.5mm A/V port
Add the devicetree describing the board's peripherals and their
connections.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20250307005712.16828-16-andre.przywara@arm.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Radxa A5E is a development board using the Allwinner A527 SoC, which
is using the same die as the A523 SoC, just exposing the pins of more
peripherals (like HDMI or the 2nd MAC). The board features:
- Allwinner A527/T527 SoC: 8 ARM Cortex-A55 cores, Mali-G57 MC1 GPU
- 1GiB/2GiB/4GiB LPDDR4 DRAM
- AXP717 + AXP323 PMICs
- Raspberry-Pi-2 compatible 40pin GPIO header
- 1 USB 2.0 type C port (OTG), also power supply
- 1 USB 3.0 type A host port (multiplexed with M.2 slot)
- 1 M.2 M-key 2230 slot, with 1 PCIe2.1 lane connected (multiplexed
with USB 3.0 port)
- MicroSD slot
- optional eMMC, 8, 16 or 32GB available
- optional on-board 16MiB bootable SPI NOR flash
- two 1Gbps Ethernet ports (via MAXIO MAE0621A PHYs)
- PoE header for optional supply circuit on one Ethernet port
- WiFi 802.11 a/b/g/n/ac/ax (LB-Link BL-M8800DS2 module using AIC8800)
- HDMI port
- camera and LCD connectors
- power supply via USB-C connector (but no PD) or GPIO header pins
This .dts describes the devices as far as we support them at the moment.
The PMIC rails have been assigned as per the schematics.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20250307005712.16828-14-andre.przywara@arm.com
[wens@csie.org: Squash in SD card detect pull resistor fix]
Link: https://patch.msgid.link/20250425003422.3465-1-andre.przywara@arm.com
[wens@csie.org: Rename dts file to sun55i-a527-cubie-a5e.dts]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The X96QPro+ is a TV box using the Allwinner H728 SoC. That SoC seems to
be a package variant of the A523 family, at least it uses the same SoC
ID and is compatible as far as we can assess.
It comes with the following specs:
- Allwinner H728 SoC: 8 Arm Cortex-A55 cores, Mali-G57 MC1 GPU
- 2 or 4GiB DDR3L DRAM
- 32, 64, or 128 GiB eMMC flash
- AXP717 + AXP323 PMICs
- Gigabit Ethernet (using MAXIO PHY)
- HDMI port
- 2 * USB 2.0 ports
- 1 * USB 3.0 port
- microSD card slot
- TOSLINK digital audio output
- 3.5mm A/V port
- infrared sensor
- 7-segment display
- 5V barrel plug power supply
- power button
The PCB provides holes for soldering a UART header or cable, this is
connected to the debug UART0. There is another set of UART pins
available. The board also features a FEL button (accessible through the
3.5mm socket) and a reset button (only accessible when case is open).
This .dts just describes the basic peripherals as far as we support them
at the moment. The PMIC rail assignments are reverse engineered as far
as possible, by dumping them from a running Android system, and correlating
them to other boards using the same SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20250307005712.16828-13-andre.przywara@arm.com
[wens@csie.org: Squash in SD card detect pull resistor fix]
Link: https://patch.msgid.link/20250425003422.3465-1-andre.przywara@arm.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Avaota A1 router board is an Open Source hardware board, designed
by YuzukiHD. Pine64 produces some boards and sells them. It uses the
Allwinner A527 or T527 SoC, and comes with the following features:
- Eight ARM Cortex-A55 cores, Mali-G57 MC1 GPU
- 1GiB/2GiB/4GiB LPDDR4 DRAM
- AXP717 + AXP323 PMIC
- Raspberry-Pi-2 compatible GPIO header
- 1 USB 2.0 type A host port, 1 USB 3.0 type A host post
- 1 USB 2.0 type C port (OTG + serial debug)
- MicroSD slot
- eMMC between 16 and 128 GiB
- on-board 16MiB bootable SPI NOR flash
- two 1Gbps Ethernet ports (via RTL8211F PHYs)
- HDMI port
- DP port
- camera and LCD connectors
- 3.5mm headphone jack
- (yet) unsupported WiFi/BT chip
- 1.3" LC display, connected via SPI
- 12 V barrel plug for power supply
Add the devicetree file describing the currently supported features.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patch.msgid.link/20250307005712.16828-12-andre.przywara@arm.com
[wens@csie.org: Squash in SD card detect pull resistor fix]
Link: https://patch.msgid.link/20250425003422.3465-1-andre.przywara@arm.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Anbernic RG35XXSP is almost identical to the RG35XX-Plus, but in a
clamshell form-factor. The key differences between the SP and the Plus
is a lid switch and an RTC on the same i2c bus as the PMIC.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20240710231718.106894-5-macroalpha82@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The RG35XX-H adds thumbsticks, a stereo speaker, and a second USB port to
the RG35XX-Plus, and has a horizontal form factor.
Enabled in this DTS:
- Thumbsticks
- Second USB port
Signed-off-by: Ryan Walklin <ryan@testtoast.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240427110225.727472-8-ryan@testtoast.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The RG35XX-Plus adds a RTL8221CS SDIO Wifi/BT chip to the RG35XX (2024).
Enabled in this DTS:
- WiFi
- Bluetooth
- Supporting power sequence and GPIOs
Signed-off-by: Ryan Walklin <ryan@testtoast.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240427110225.727472-7-ryan@testtoast.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The base model RG35XX (2024) is a handheld gaming device based on an
Allwinner H700 chip.
The H700 is a H616 variant (4x ARM Cortex-A53 cores @ 1.5Ghz with Mali G31
GPU) which exposes RGB LCD and NMI pins.
Device features:
- Allwinner H700 @ 1.5GHz
- 1GB LPDDR4 DRAM
- X-Powers AXP717 PMIC
- 3.5" 640x480 RGB LCD
- Two microSD slots
- Mini-HDMI out
- GPIO keypad
- 3.5mm headphone jack
- USB-C charging port
Enabled in this DTS:
- AXP717 PMIC with RSB serial interface, regulators and NMI interrupt
controller
- Power LED (charge LED on device controlled directly by PMIC)
- Serial UART (accessible from headers on the board)
- First SD slot (SD2 appears to have a GPIO-switched regulator for 1.8v
low-voltage signalling, this is not yet modeled. Enablement with a
switched regulator will be confirmed and posted in a follow-up patch).
Signed-off-by: Ryan Walklin <ryan@testtoast.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20240427110225.727472-6-ryan@testtoast.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The Tanix TX1 is a tiny TV box with the Allwinner H313 SoC. The box
features no Ethernet or an SD card slot, which makes booting from it
somewhat interesting: Pressing the hidden FEL button and using a USB-A
to USB-A cable to upload code from a host PC is one way to run mainline.
The box features:
- Allwinner H313 SoC (4 * Arm Cortex-A53 cores)
- 1 or 2 GB DRAM
- 8 or 16 GB eMMC flash
- SCI S9082H WiFi chip
- HDMI port
- one USB 2.0 port
- 3.5mm AV port
- barrel plug 5V DC input via barrel plug
The devicetree covers most peripherals.
The eMMC did not work properly in HS200 speed mode, so this mode property
is omitted. HS-DDR seems to work fine.
The blue LED is connected to the same GPIO pin as the red LED, just
using the opposite polarity. Apparently there is no way of describing
this in DT, so the red LED is omitted.
Next to the FEL button is a hidden button, that can be pushed by using
something like a paperclip, through the ventilation vents of the case.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240418104942.1556914-3-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The Sipeed Longan SoM 3H is a system on module based on the Allwinner
H618 SoC. The SoM features:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 2/4 GiB LPDDR4 DRAM SoMs
- AXP313a PMIC
- eMMC
The Sipeed Longan PI 3H is a development board based on the above SoM.
The board features:
- Longan SoM 3H
- Raspberry-Pi-1 compatible GPIO header
- 2 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- 1Gbps Ethernet port (via RTL8211 PHY)
- HDMI port
- WiFi/BT chip
Add the devicetree file describing the currently supported features,
namely PMIC, LEDs, UART, SD card, eMMC, USB and Ethernet.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240211081739.395-3-jszhang@kernel.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The Remix Mini PC is a "mini computer" using the Allwinner H64 SoC,
which appears to be just a relabelled A64. It was launched in 2015 by
the now defunct company Jide, and shipped with a desktop optimised
version of Android. It features
- Allwinner H64 Soc (4 * Arm Cortex-A53 cores)
- 1 or 2 GB DRAM
- 8 or 16 GB eMMC flash
- 100 MBit Ethernet port (using an X-Powers AC200 PHY)
- RTL8723BS WiFi & Bluetooth chip
- HDMI port
- two USB 2.0 ports
- 3.5mm AV port
- microSD card slot
The devicetree covers most peripherals, though there is no agreed
binding for the PHY chip yet, so this is left out.
The eMMC did not work with the MMC DDR speed mode, so this mode property
is omitted.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240209114018.3580370-4-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Orange Pi Zero 2W dts file is not included in Makefile. Fix this.
Fixes: c505ee1eae ("arm64: dts: allwinner: h616: add Orange Pi Zero 2W support")
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20240222211326.114955-1-jernej.skrabec@gmail.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
This is a Chinese TV box, probably very similar if not identical to
various other cheap TV boxes with the same specs:
- Allwinner H618 SoC (4 * Arm Cortex-A53 cores, 1MB L2 cache)
- 2 or 4GiB DDR3L DRAM
- 32, 64, or 128 GiB eMMC flash
- AXP313a PMIC
- 100 Mbit/s Ethernet (using yet unsupported internal PHY)
- HDMI port
- 2 * USB 2.0 ports
- microSD card slot
- 3.5mm A/V port
- 7-segment display
- 5V barrel plug power supply
The PCB provides holes for soldering a UART header or cable, this is
connected to the debug UART0. UART1 is used for the Bluetooth chip,
although this isn't working yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20231214015312.17363-4-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The BigTreeTech Pi is an H616 based board based on CB1.
Just in Rpi format board.
It features the same internals as BTT CB1 but adds:
- Fan port
- IR receiver
- ADXL345 Accelerometer connector via SPI
- 24V DC power supply via terminal plugs
- USB to CAN module connector (External Module)
List of currently working things is same as BTT CB1 but also:
- IR receiver
- ADXL345 connector
Signed-off-by: Martin Botka <martin@biqu3d.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230912-b4-cb1-v6-4-bb11238f3a9c@somainline.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
CB1 is Compute Module style board that plugs into Rpi board style adapter or
Manta 3D printer boards (M4P/M8P).
The SoM features:
- H616 SoC
- 1GiB of RAM
- AXP313A PMIC
- RTL8189FTV WiFi
Boards feature:
- 4x USB via USB2 hub (usb1 on SoM).
- SDcard slot for loading images.
- Ethernet port wired to the internal PHY. (100M)
- 2x HDMI 2.0. (Only 1 usable on CB1)
- Power and Status LEDs. (Only Status LED usable on CB1)
- 40 pin GPIO header
Currently working:
- Booting
- USB
- UART
- MMC
- Status LED
- WiFi (RTL8189FS via out of tree driver)
I didnt want to duplicate things so the manta DTS can also be used on BTT pi4b adapter.
CB1 SoM has its own DTSI file in case other boards shows up that accept this SoM.
Signed-off-by: Martin Botka <martin.botka@somainline.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230912-b4-cb1-v6-3-bb11238f3a9c@somainline.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The OrangePi Zero 3 is a development board based on the Allwinner H618 SoC,
which seems to be just an H616 with more L2 cache. The board itself is a
slightly updated version of the Orange Pi Zero 2. It features:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 1/1.5/2/4 GiB LPDDR4 DRAM SKUs (only up to 1GB on the Zero2)
- AXP313a PMIC (more capable AXP305 on the Zero2)
- Raspberry-Pi-1 compatible GPIO header
- extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
- 1 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- on-board 16MiB bootable SPI NOR flash (only 2MB on the Zero2)
- 1Gbps Ethernet port (via Motorcomm YT8531 PHY) (RTL8211 on the Zero2)
- micro-HDMI port
- (yet) unsupported Allwinner WiFi/BT chip
Add the devicetree file describing the currently supported features,
namely LEDs, SD card, PMIC, SPI flash, USB. Ethernet seems unstable at
the moment, though the basic functionality works.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230804170856.1237202-4-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The X96 Mate is an Allwinner H616 based TV box, featuring:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 2GiB/4GiB RAM (fully usable!)
- 16/32/64GiB eMMC
- 100Mbps Ethernet (via embedded AC200 EPHY, not yet supported)
- Unsupported Allwinner WiFi chip
- 2 x USB 2.0 host ports
- HDMI port
- IR receiver
- 5V/2A DC power supply via barrel plug
Add a basic devicetree for it, with SD card and eMMC working, as
well as serial and the essential peripherals, like the AXP PMIC.
This DT is somewhat minimal, and should work on many other similar TV
boxes with the Allwinner H616 chip.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220708105235.3983266-8-andre.przywara@arm.com
The OrangePi Zero 2 is a development board with the new H616 SoC. It
comes with the following features:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 512MiB/1GiB DDR3 DRAM
- AXP305 PMIC
- Raspberry-Pi-1 compatible GPIO header
- extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
- 1 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- on-board 2MiB bootable SPI NOR flash
- 1Gbps Ethernet port (via RTL8211F PHY)
- micro-HDMI port
- (yet) unsupported Allwinner WiFi/BT chip
Add the devicetree file describing the currently supported features.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220708105235.3983266-7-andre.przywara@arm.com
Tanix TX6 mini is less capable version of Tanix TX6 although it comes
with some features not present on Tanix TX6.
Basic specs:
- H6 SoC
- 2 GiB DDR3 RAM
- HDMI
- SPDIF
- 2x USB
- analogue audio
- CVBS
- SD card
- IR remote
- LED display
- fast ethernet
- XR819 wifi
- 16 GiB eMMC
Currently supported features doesn't differ that much from Tanix TX6,
but that will change soon.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The NanoPi R1S H5 is a open source board made by FriendlyElec.
It has the following features:
- Allwinner H5, Quad-core Cortex-A53
- 512MB DDR3 RAM
- 10/100/1000M Ethernet x 2
- RTL8189ETV WiFi 802.11b/g/n
- USB 2.0 host port (A)
- MicroSD Slot
- Serial Debug Port
- 5V 2A DC power-supply
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210516163523.9484-2-amadeus@jmu.edu.cn
PineTabs since Early Adopter batch will use a new LCD panel.
Add device tree for PineTab with the new panel.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201224024001.19248-2-icenowy@aosc.io
A100 perf1 is an Allwinner A100-based SBC, with the following features:
- 1GiB DDR3 DRAM
- AXP803 PMIC
- 2 USB 2.0 ports
- MicroSD slot and on-board eMMC module
- on-board Nand flash
- ···
Adds initial support for it, including UART and PMU.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/30f4a3fc6ac84d05094e2c3b89d1dddc8ff6b7fc.1595572867.git.frank@allwinnertech.com
Revision 1.2 should be the final production version of the PinePhone.
It has most of the known HW quirks fixed.
Interrupt to the magnetometer is routed correctly, in this revision.
The bulk of the changes are in how modem and the USB-C HDMI bridge
chip is powered and where the signals from the modem are connected.
Also backlight intensity seemingly behaves differently, than on the
1.1 and 1.0 boards, and the PWM duty cycle where backlight starts
to work is 10% (as tested on 2 1.2 PinePhones I have access to).
Signed-off-by: Ondrej Jirman <megous@megous.com>
Link: https://lore.kernel.org/r/20200703194842.111845-3-megous@megous.com
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
At the moment PinePhone comes in two slightly incompatible variants:
- 1.0: Early Developer Batch
- 1.1: Braveheart Batch
There will be at least one more incompatible variant in the very near
future, so let's start by sharing the dtsi among multiple variants,
right away, even though the HW description doesn't yet include the
different bits.
The differences between 1.0 and 1.1 are: change in pins that control
the flash LED, differences in modem power status signal routing, and
maybe some other subtler things, that have not been determined yet.
This is a basic DT that includes only features that are already
supported by mainline drivers.
Co-developed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Co-developed-by: Martijn Braam <martijn@brixit.nl>
Signed-off-by: Martijn Braam <martijn@brixit.nl>
Co-developed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
PineTab is a 10.1" tablet by Pine64 with Allwinner A64 inside.
It includes the following peripherals:
USB:
- A microUSB Type-B port connected to the OTG-capable USB PHY of
Allwinner A64. The ID pin is connected to a GPIO of the A64 SoC, and the
Vbus is connected to the Vbus of AXP803 PMIC. These enables OTG
functionality on this port.
- A USB Type-A port is connected to the internal hub attached to the
non-OTG USB PHY of Allwinner A64.
- There are reserved pins for an external keyboard connected to the
internal hub.
Power:
- The microUSB port has its Vbus connected to AXP803, mentioned above.
- A DC jack (of a strange size, 2.5mm outer diameter) is connected to
the ACIN of AXP803.
- A Li-Polymer battery is connected to the battery pins of AXP803.
Storage:
- An tradition Pine64 eMMC slot is on the board, mounted with an eMMC
module by factory.
- An external microSD slot is hidden under a protect case.
Display:
- A MIPI-DSI LCD panel (800x1280) is connected to the DSI port of A64 SoC.
- A mini HDMI port.
Input:
- A touch panel attached to a Goodix GT9271 touch controller.
- Volume keys connected to the LRADC of the A64 SoC.
Camera:
- An OV5640 CMOS camera is at rear, connected to the CSI bus of A64 SoC.
- A GC2145 CMOS camera is at front, shares the same CSI bus with OV5640.
Audio:
- A headphone jack is conencted to the SoC's internal codec.
- A speaker connected is to the Line Out port of SoC's internal codec, via
an amplifier.
Misc:
- Debug UART is muxed with the headphone jack, with the switch next to
the microSD slot.
- A bosch BMA223 accelerometer is connected to the I2C bus of A64 SoC.
- Wi-Fi and Bluetooth are available via a RTL8723CS chip, similar to the
one in Pinebook.
This commit adds a basically usable device tree for it, implementing
most of the features mentioned above. HDMI is not supported now because
bad LCD-HDMI coexistence situation of mainline A64 display driver, the
front camera currently lacks a driver and a facility to share the bus
with the rear one, and the accelerometer currently lacks a DT binding.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The Libre Computer ALL-H5-CC board is an upgraded version of the
ALL-H3-CC. Changes include:
- Gigabit Ethernet via external RTL8211E Ethernet PHY
- 16 MiB SPI NOR flash memory
- PoE tap header
- Line out jack removed
Only H5 variant test samples were made available, and the vendor is not
certain whether other SoC variants would be made or not. Furthermore the
board is a minor upgrade compared to the ALL-H3-CC. Thus the device tree
simply includes the one for the ALL-H3-CC, and adds the changes on top.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The Libre Computer ALL-H3-IT board is a small single board computer that
is roughly the same size as the Raspberry Pi Zero, or around 20% smaller
than a credit card.
The board features:
- H2, H3, or H5 SoC from Allwinner
- 2 DDR3 DRAM chips
- Realtek RTL8821CU based WiFi module
- 128 Mbit SPI-NOR flash
- micro-SD card slot
- micro HDMI video output
- FPC connector for camera sensor module
- generic Raspberri-Pi style 40 pin GPIO header
- additional pin headers for extra USB host ports, ananlog audio and
IR receiver
Only H5 variant test samples were made available, but the vendor does
have plans to include at least an H3 variant. Thus the device tree is
split much like the ALL-H3-CC, with a common dtsi file for the board
design, and separate dts files including the common board file and the
SoC dtsi file. The other variants will be added as they are made
available.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This patch adds the model B of the PineH64.
The model B is smaller than the pine64 model A and has no PCIE slot.
The only devicetree difference with the pineH64 model A, is the PHY
regulator and the HDMI connector node.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.
This patch has been tested on A64-OLinuXino-1Ge16GW with Linux 5.0 from Debain.
Basic benchmarks using Flexible IO Tester show reasonable performance from the
eMMC.
eMMC - Random Write: 21.3MiB/s
eMMC - Sequential Write: 68.2MiB/s
SD Card - Random Write: 1690KiB/s
SD Card - Sequential Write: 11.0MiB/s
Changes:
v3: Separate dts for eMMC variants
v2: Fix descriptions for VCC and VCCQ
Link: 174953de1e
Signed-off-by: Martin Ayotte <martinayotte@gmail.com>
[sunil@medhas.org Fix descriptions for VCC and VCCQ, separate dts for eMMC]
Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org>
Tested-by: Sunil Mohan Adapa <sunil@medhas.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tanix TX6 is an Allwinner H6 based TV box, which supports:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 4GiB DDR3 RAM (3GiB useable)
- 100Mbps EMAC via AC200 EPHY
- Cdtech 47822BS Wifi/BT
- 2x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- IR receiver
- 64GiB eMMC
- 5V/2A DC power supply
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Orange Pi 3 is a H6 based SBC made by Xulong, released in January 2019. It
has the following features:
- Allwinner H6 quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB or 2GB LPDDR3 RAM
- AXP805 PMIC
- AP6256 Wifi/BT 5.0
- USB 2.0 host port (A)
- USB 2.0 micro usb, OTG
- USB 3.0 Host + 4 port USB hub (GL3510)
- Gigabit Ethernet (Realtek RTL8211E phy)
- HDMI 2.0 port
- soldered eMMC (optional)
- 3x LED (one is on the bottom)
- microphone
- audio jack
- PCIe
Add basic support for the board.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- FN-Link 6222B-SRB Wifi/BT
- 1x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- S/PDIF Tx
- IR receiver
- 5V/2A DC power supply
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Oceanic 5205 5inMFD is a 5 inch Multi function display baseboard
designed to mount SoPine SOM.
Key features:
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 2GB DDR3 RAM
- SD Slot
- SPI-NOR flash
- EMAC, RTL8211E
- MCP2515 CAN
- 4-lane, MIPI-DSI panel
- Goodix 911 CTP
- USB Host
- 12V DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Our usual pull request with the changes shared between the H3 and H5 SoCs.
The major changes for this release are:
- Addition of the video engine for the H5
- H3 Camera support
- New board: Emlid Neutis N5, Mapleboard MP130
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXAqJJwAKCRDj7w1vZxhR
xTq4AP9SxrPeKDTBD4mKV+PVuJ2qq919M6o+mcxDkCecEMfbagD+JLkt2uGzdpb8
eC6CuieHvJq1y/akfDpRBf0ZZD0/bw0=
=yRd0
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner H3/H5 changes for 4.21
Our usual pull request with the changes shared between the H3 and H5 SoCs.
The major changes for this release are:
- Addition of the video engine for the H5
- H3 Camera support
- New board: Emlid Neutis N5, Mapleboard MP130
* tag 'sunxi-h3-h5-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h5: Add Video Engine node
ARM/arm64: dts: allwinner: Move H3/H5 syscon label over to soc-specific nodes
arm64: dts: allwinner: h5: Add system-control node with SRAM C1
ARM: dts: sun8i: h3: Fix the system-control register range
ARM: dts: sun8i: Add the H3/H5 CSI controller
ARM: dts: sun8i-h3: Add dts for the Mapleboard MP130
arm64: dts: allwinner: new board - Emlid Neutis N5
dt-bindings: vendor-prefix: new vendor - Emlid
ARM: dts: sun8i-h3: add sy8106a to orange pi plus
Signed-off-by: Olof Johansson <olof@lixom.net>
OrangePi Lite2 is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- AP6356S Wifi/BT
- USB 2.0, USB 3.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
module, DDR3 RAM and eMMC.
- add neutis n5 dtsi file for SoM needs
- add neutis devboard dts file
- add neutis devboard target to dtb makefile
Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Our usual set of DT changes for the arm64 Allwinner SoCs.
The most notable things are:
- HDMI support on the A64
- New boards: OrangePi One Plus
-----BEGIN PGP SIGNATURE-----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=sPs9
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner arm64 DT changes for 4.20
Our usual set of DT changes for the arm64 Allwinner SoCs.
The most notable things are:
- HDMI support on the A64
- New boards: OrangePi One Plus
* tag 'sunxi-dt64-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (28 commits)
arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay
arm64: dts: allwinner: a64: Enable HDMI output on A64 boards w/ HDMI
arm64: dts: allwinner: a64: Add display pipeline
arm64: dts: allwinner: h6: add system controller device tree node
arm64: dts: allwinner: h6: Add OrangePi One Plus initial support
arm64: dts: allwinner: a64: Rename r_i2c_pins_a label to r_i2c_pl89_pins
arm64: dts: allwinner: a64: Rename uart0_pins_a label to uart0_pb_pins
arm64: dts: allwinner: a64: Split out data strobe pin from mmc2 pinmux
arm64: dts: allwinner: a64: NanoPi-A64: Add blue status LED
arm64: dts: allwinner: a64: NanoPi-A64: Add Wifi chip
arm64: dts: allwinner: a64: NanoPi-A64: Add Ethernet
arm64: dts: allwinner: a64: NanoPi-A64: Fix DCDC1 voltage
arm64: dts: allwinner: a64: Olinuxino: enable USB
arm64: dts: allwinner: a64: Olinuxino: add Ethernet nodes
arm64: dts: allwinner: a64: Olinuxino: fix DRAM voltage
arm64: dts: allwinner: a64: Orange Pi Win: Adjust CSI power rails
arm64: dts: allwinner: a64: Orange Pi Win: Add SPI flash node
arm64: dts: allwinner: a64: Orange Pi Win: Add SDIO node
arm64: dts: allwinner: a64: Orange Pi Win: Add LED node
arm64: dts: allwinner: a64: Orange Pi Win: Add UARTs
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Bananapi released an updated revision of the H3/H5 based Bananapi M2+.
Version 1.2 enables voltage control for the CPU's regulator by using
a GPIO line to toggle a MOSFET that can change the effective resistance
value in the regulator's feedback network.
This patch adds a common .dtsi file for this new revision, which
includes the original common sunxi-bananapi-m2-plus.dtsi file, and
adds the GPIO-controlled regulator and a cpu-supply reference. H3
and H5 variant dts files are added as well.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Bananapi M2 Plus H5 is a variant of the original Bananapi M2 Plus,
with the H3 SoC replaced with an H5. Everything else is the same.
Add a stub device tree incorporating the shared bananapi-m2-plus dtsi
file.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211
- USB 2.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Pine64-LTS is a variant of the Pine64 board, from the software
visible side resembling a SoPine module on a baseboard, though the
board has the SoC and DRAM integrated on one PCB.
Due to this it basically shares the DT with the SoPine baseboard, which
we mimic in our DT by inclucing the boardboard .dts into the new file,
just overwriting the model name.
Having a separate .dts for this seems useful, since we don't know yet if
there are subtle differences between the two. Also the SoC on the LTS
board is technically an "R18" instead of the original "A64", although as
far as we know this is just a relabelled version of the original SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Pinebook is a A64-based laptop produced by Pine64, with the following
peripherals:
USB:
- Two external USB ports (one is directly connected to A64's OTG
controller, the other is under a internal hub connected to the host-only
controller.)
- USB HID keyboard and touchpad connected to the internal hub.
- USB UVC camera connected to the internal hub.
Power-related:
- A DC IN jack connected to AXP803's DCIN pin.
- A Li-Polymer battery connected to AXP803's battery pins.
Storage:
- An eMMC by Foresee on the main board (in the product revision of the
main board it's designed to be switchable).
- An external MicroSD card slot.
Display:
- An eDP LCD panel (1366x768) connected via an ANX6345 RGB-eDP bridge.
- A mini HDMI port.
Misc:
- A Hall sensor designed to detect the status of lid, connected to GPIO PL12.
- A headphone jack connected to the SoC's internal codec.
- A debug UART port muxed with headphone jack.
This commit adds basical support for it.
[vasily: squashed several commits into one, added simplefb node, added usbphy
to ehci0 and ohci0 nodes and other cosmetic changes to dts]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry
Pi B+ form factor single board computer based on the Allwinner H2+, H3,
or H5 SoCs with the same PCB.
The board has 2GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes
and connectors are in the exact same position as on the Raspberry Pi B+.
This patch enables the H5 variant using the H3 board definition moved to
a common dtsi in an earlier patch. The dts simply include the common dtsi
and declares the correct compatible and model of the H5 variant.
Suggested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The dtb entries for NanoPi boards in the device tree makefile somehow
ended up after the Orange Pi boards.
Move them so the list is properly sorted.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Here is our usual bunch of changes to the common DTSI shared between arm
and arm64, and their associated device trees.
Even though the diffstat is quite big, it's been mostly just cleanups. The
big feature is that the HDMI is now suported on H3 and H5 boards.
-----BEGIN PGP SIGNATURE-----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=hXvM
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner H3/H5 changes for 4.17" from Maxime Ripard:
Here is our usual bunch of changes to the common DTSI shared between arm
and arm64, and their associated device trees.
Even though the diffstat is quite big, it's been mostly just cleanups. The
big feature is that the HDMI is now suported on H3 and H5 boards.
* tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus
ARM: dts: sun8i-h3: Add Mali node
ARM64: dts: sun50i: h5: Enable HDMI output on H5 boards
ARM: dts: sun8i: h3: Enable HDMI output on H3 boards
ARM: dts: sunxi: h3/h5: Add HDMI pipeline
ARM: dts: sun8i: h2-plus: remove unnecessary mmc1_pins node
ARM: dts: sunxi: h3-h5: rename mmc0_pins_a and mmc1_pins_a
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc1 from dts to dtsi
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc0 from dts to dtsi
ARM: dts: sunxi: h3-h5: remove mmc0 card detection pin from pinctrl
ARM: dts: sun8i: h2+: add support for Banana Pi M2 Zero board
ARM: dts: sunxi: Switch MMC nodes away from cd-inverted property
ARM: dts: nanopi-neo-air: Add WiFi / eMMC
The Xunlong Orange Pi Zero Plus is single board computer.
- H5 Quad-core 64-bit Cortex-A53
- 512MB DDR3
- microSD slot
- Debug TTL UART
- 1000M/100M/10M Ethernet RJ45
- Realtek RTL8189FTV
- Spi flash (2MB)
- One USB 2.0 HOST, One USB 2.0 OTG
This is based on a patch from armbian:
https://github.com/armbian/build/blob/master/patch/kernel/sunxi-next/sunxi-add-orangepi-zero-plus.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The TERES-I is an open hardware laptop built by Olimex using the
Allwinner A64 SoC.
Add the board specific .dts file, which includes the A64 .dtsi and
enables the peripherals that we support so far.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
