Commit 4fc8cb47fc ("drm/display: Move HDMI helpers into display-helper
module") turned the DRM_DW_HDMI dependency of DRM_SUN8I_DW_HDMI into a
depends on which ended up disabling the driver in the defconfig. Make
sure it's still enabled.
Fixes: 4fc8cb47fc ("drm/display: Move HDMI helpers into display-helper module")
Reported-by: Mark Brown <broonie@kernel.org>
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240403-fix-dw-hdmi-kconfig-v1-5-afbc4a835c38@kernel.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
According to https://www.kernel.org/doc/html/latest/timers/no_hz.html,
CONFIG_NO_HZ=y should be replaced by CONFIG_NO_HZ_IDLE=y for newer
kernels, so let's reflect that in the 32-bit ARM defconfigs.
Signed-off-by: Stefan Hansson <newbie13xd@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> # Samsung
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220825162034.5901-1-newbie13xd@gmail.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The debug-info and can subystem options have moved around in the
'savedefconfig' output, so fix these up to reduce the clutter
from the savedefconfig command.
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A lot of Kconfig options have changed over the years, and we tend
to not do a blind 'make defconfig' to refresh the files, to ensure
we catch options that should not have gone away.
I used some a bit of scripting to only rework the bits where an
option moved around in any of the defconfig files, without also
dropping any of the other lines, to make it clearer which options
we no longer have.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In the patch ("drm/panel-simple-edp: Split eDP panels out of
panel-simple") we will split the PANEL_SIMPLE driver in two. By
default let's give everyone who had the old driver enabled the new
driver too. If folks want to opt-out of one or the other they always
can later.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.5.I02250cd7d4799661b068bcc65849a456ed411734@changeid
Commit 7ecdea4a02 ("backlight: generic_bl: Remove this driver as it is
unused") removed geenric_bl driver from the tree, together with
corresponding config option.
Remove BACKLIGHT_GENERIC config item from all ARM configurations.
Fixes: 7ecdea4a02 ("backlight: generic_bl: Remove this driver as it is unused")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Link: https://lore.kernel.org/r/20201201222922.3183-2-andrey.zhizhikin@leica-geosystems.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Lot of sunxi boards has a Realtek PHY, so let's enable it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201112202652.27676-1-clabbe@baylibre.com
The mailbox found on the A31 and later SoCs have recently gained some
support in Linux. Since it's going to be useful for crust, let's enable it
in our defconfig.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200706132323.147562-2-maxime@cerno.tech
We're missing a bunch of options related to the DRM driver options (panels,
HDMI, CEC) that seems useful. Let's add them in the defconfig.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200705091904.42795-5-maxime@cerno.tech
Acked-by: Chen-Yu Tsai <wens@csie.org>
We've had drivers for the deinterlace and rotation engines for a while now,
let's enable them in the defconfig.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200705091904.42795-3-maxime@cerno.tech
Acked-by: Chen-Yu Tsai <wens@csie.org>
We've had CSI drivers for the older and newer SoCs for a while now, let's
enable them in the defconfig.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200705091904.42795-2-maxime@cerno.tech
Acked-by: Chen-Yu Tsai <wens@csie.org>
We haven't run savedefconfig for a while and some options have moved
around. In order to ease the patch application / conflict resolution, let's
run it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200705091904.42795-1-maxime@cerno.tech
On my orange pi PC, I got lot of "sun4i-codec 1c22c00.codec: Failed to register our card".
This was due to a missing component: the sun8i analog codec.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The dumb-vga-dac driver can support simple DRM bridges without being
limited to VGA DACs. Rename it to simple-bridge.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-12-laurent.pinchart@ideasonboard.com
Many sunxi based board needs CONFIG_SUN8I_THERMAL for thermal support.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Include support for Micrel KSZ9031 PHY driver in sunxi_defconfig,
which fixes issues of link not coming up at boot time with
certain link partners.
Micrel KSZ9031 PHY chip is used on Olimex A20-OLinuXino-LIME2
boards.
The errata fix itself has been implemented in commit
"3aed3e2a143c96: net: phy: micrel: add Asym Pause workaround"
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This patch adds the new Allwinner crypto configs to sunxi_defconfig
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The DRM driver most notably, but also out of tree drivers (for now) like
the VPU or GPU drivers, are quite big consumers of large, contiguous memory
buffers. However, the sunxi_defconfig doesn't enable CMA in order to
mitigate that, which makes them almost unusable.
Enable it to make sure it somewhat works.
Cc: <stable@vger.kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This branch contains platform updates for 32- and 64-bit ARM,
including defconfig updates to enable new options, drivers and
platforms. There are also a few fixes and cleanups for some existing vendors.
Some of the things worth highlighting here are:
- Enabling new crypt drivers on arm64 defconfig
- QCOM IPQ8074 clocks and pinctrl drivers on arm64 defconfig
- Debug support enabled for Renesas r8a7743
- Various config updates for Renesas platforms (sound, USB, other drivers)
- Platform support (including SMP) for TI dra762
- OMAP cleanups: Move to use generic 8250 debug_ll, removal of stale DMA code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZtdXjAAoJEIwa5zzehBx3ExIQAJQ6anSZlkGysXqptA4c1HuL
vgGq/U5xZ1Wa4Z/YX7//wuCMwRClc1j/zSJ5PP+wP0YsaviN7iF/8H1P/HQtCiTT
DcEQPSI770829wzW4oMNW0PyU/ZnWMtuiMB+FAjdPVjbS8bT4PIK72D8PYKrT7f8
8bU51+QezjSLamQaA8S2RyX+kYI/4znTa/9Aco4AlCtioV8h9gQanFYd2EI/EMhU
1uvR3xUFf/YK49+M5J6m3DvtFffllHU9TKV/EAQD1Bhl1s5VPfem+a8JbVh1m7M+
NzQOOoPJ9jYOGfjlaQQVmZ/1E4iKac1oK4x44Djk/i+RFjl+AT/2co3RcaEq9Npw
5HNsK8ujnjzWB3xHu5wK5CbrjLNYco9hOpJaGkSeClo4ElDJVSKxyqWkZuhhnSA8
bXXV5VraMX67tjG7Ou8+NtdbMkGdOUqnNbuBlCxkxpWxhtaUQG1YHHQDofUXNguy
rtVhKRZRSkNYrp4lDCKCXVFFO077FGzP2Boq6JVzLv+U1l6JlZkkr3EWKYMY45HC
o2rVcAB4lMR/k6tqE5MAmQC53jCNlFZt2xtf1WRVKf+0TfBVIGX3MxvFxl4E9wA+
9pdJ9ujZWsPjTcZcktA6AsaK7uevRxcB2YZYv4pXVjR1RcZ/SfiEf4UW+md3j4QB
igKej5WsRiCPwnkMFKs0
=g8cF
-----END PGP SIGNATURE-----
Merge tag 'armsoc-platforms' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM/arm64 SoC platform updates from Olof Johansson: "This branch
contains platform updates for 32- and 64-bit ARM, including defconfig
updates to enable new options, drivers and platforms. There are also a
few fixes and cleanups for some existing vendors.
Some of the things worth highlighting here are:
- Enabling new crypt drivers on arm64 defconfig
- QCOM IPQ8074 clocks and pinctrl drivers on arm64 defconfig
- Debug support enabled for Renesas r8a7743
- Various config updates for Renesas platforms (sound, USB, other
drivers)
- Platform support (including SMP) for TI dra762
- OMAP cleanups: Move to use generic 8250 debug_ll, removal of stale
DMA code"
* tag 'armsoc-platforms' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (109 commits)
ARM: multi_v7_defconfig: make eSDHC driver built-in
arm64: defconfig: enable rockchip graphics
MAINTAINERS: Update Cavium ThunderX2 entry
ARM: config: aspeed: Add I2C, VUART, LPC Snoop
ARM: configs: aspeed: Update Aspeed G4 with VMSPLIT_2G
ARM: s3c24xx: Fix NAND ECC mode for mini2440 board
ARM: davinci_all_defconfig: enable tinydrm and ST7586
arm64: defconfig: Enable QCOM IPQ8074 clock and pinctrl
ARM: defconfig: tegra: Enable ChipIdea UDC driver
ARM: configs: Add Tegra I2S interfaces to multi_v7_defconfig
ARM: tegra: Add Tegra I2S interfaces to defconfig
ARM: tegra: Update default configuration for v4.13-rc1
MAINTAINERS: update ARM/ZTE entry
soc: versatile: remove unnecessary static in realview_soc_probe()
ARM: Convert to using %pOF instead of full_name
ARM: hisi: Fix typo in comment
ARM: multi_v7_defconfig: add CONFIG_BRCMSTB_THERMAL
arm64: defconfig: add CONFIG_BRCMSTB_THERMAL
arm64: defconfig: add recently added crypto drivers as modules
arm64: defconfig: enable CONFIG_UNIPHIER_WATCHDOG
...
There is no dependency between the two, so remove the dependency in
Kconfig files.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
AXP20X_POWER depends on IIO. Even though it does not depend on AXP20X_ADC,
it is the new, preferred way of getting power supply configuration, it's
going to be enabled anyway.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A bunch of new power supplies have been added recently to handle the
batteries and the AC-IN plugs. Add them to our defconfig.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Update the defconfig with the current state of defaults.
This was done using make sunxi_defconfig; make savedefconfig
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the AC100 RTC driver so boards with it can keep track of time.
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This enables CONFIG_THERMAL_OF by default for sunxi_defconfig. It is
required to get Allwinner SoCs' temperature from the GPADC driver.
The Allwinner SoCs all have an ADC that can also act as a touchscreen
controller and a thermal sensor. The first four channels can be used
either for the ADC or the touchscreen and the fifth channel is used for
the thermal sensor.
The thermal sensor requires the IP to be in touchscreen mode to return
correct values. Therefore, if the user is continuously reading the ADC
channel(s), the thermal framework in which the thermal sensor is
registered will switch the IP in touchscreen mode to get a temperature
value and requires a delay of 100ms (because of the mode switching),
then the ADC will switch back to ADC mode and requires also a delay of
100ms. If the ADC readings are critical to user and the SoC temperature
is not, the GPADC driver is capable of not registering the thermal
sensor in the thermal framework and thus, "quicken" the ADC readings. In
most use cases, the SoC temperature is more critical (for cpu throttling
for example or activating cooling devices) than ADC readings, thus it is
now enabled by default.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the new DRM driver in the sunxi default configuration
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner SoCs typically have a Mentor Graphics Inventra MUSB dual role
controller for USB OTG.
Now that the issue with MUSB and USB gadget registration order has been
resolved, we can enable this driver in dual role mode. This requires the
NOP USB transceiver driver, which is also enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sunxi_defconfig already enables INPUT_AXP20X_PEK, but the device is not
exposed to userspace. Enable INPUT_EVDEV so it is.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A consumer IR receiver is commonly found on Allwinner SoC based
development boards and set top boxes. The driver has been available
for some time. Enable it by default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As usual, a bunch of commits, mostly adding drivers and other options to
defconfigs because it makes sense to have them enabled on various development
or product boards. Too much to enumerate each here.
There's an introduction of a pxa_defconfig, since PXA finally will allow
building a shared kernel for all boards. With this, we can hopefully
remove a bunch of individual defconfigs down the road but it requires
a bit of real life testing and transition period.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YsCa
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Olof Johansson:
"As usual, a bunch of commits, mostly adding drivers and other options
to defconfigs because it makes sense to have them enabled on various
development or product boards. Too much to enumerate each here.
There's an introduction of a pxa_defconfig, since PXA finally will
allow building a shared kernel for all boards. With this, we can
hopefully remove a bunch of individual defconfigs down the road but it
requires a bit of real life testing and transition period"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (65 commits)
ARM: Add CONFIG_DEPRECATED_PARAM_STRUCT to netwinder_defconfig
ARM: multi_v7_defconfig: Add rockchip audio support
arm: multi_v7_defconfig: Add virtio drivers
ARM: zx_defconfig: remove CONFIG_MMC_DW_IDMAC
ARM: versatile: enable the right LEDs
ARM: pxa: add defconfig covering all the boards
ARM: versatile: select some defaults in defconfig
ARM: multi_v7_defconfig: Enable fan, sensors and audio for Odroid XU3
ARM: bcm2835: enable auxiliary spi driver in defconfig
ARM: bcm2835: enable all bcm2835-relevant in defconfig
ARM: default to multi_v7_defconfig
ARM: multi_v7_defconfig: enable rk808 clkout module
ARM: multi_v7_defconfig: enable rockchip crypto module
ARM: multi_v7_defconfig: enable Rockchip io-domain driver
ARM: multi_v7_defconfig: Enable generic SoC internal OMAP regulators
ARM: multi_v7_defconfig: Enable AM437x PMIC TPS65218
ARM: multi_v7_defconfig: enable TPS65217 regulator
ARM: realview: select apropriate targets
ARM: defconfig: qcom: Enable SSBI drivers
ARM: defconfig: Update qcom_defconfig
...
Commit 69fb4dcada ("power: Add an axp20x-usb-power driver") introduced a new
driver for the USB power supply used on various Allwinner based SBCs. However,
the driver was not added to sunxi_defconfig which breaks USB support for some
boards (e.g. LeMaker BananaPi) as the kernel will now turn off the USB power
supply during boot by default if the driver isn't present. (This was not the
case in linux 4.3 or lower where the USB power was always left on.)
Hence, add the driver to sunxi_defconfig in order to keep USB support working
on those boards that require it.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Reported-by: David Tulloh <david@tulloh.id.au>
Tested-by: David Tulloh <david@tulloh.id.au>
Tested-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Clean up sunxi_defconfig by generating a fresh file via
make sunxi_defconfig
make savedefconfig
While this moves around a few lines and removes unnecessary symbols,
it doesn't introduce any functional changes. The resulting .config is
identical before and after this patch.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Commit be8becb81b ("ARM: sunxi_defconfig: Enable LRADC keys
(KEYBOARD_SUN4I_LRADC)") added CONFIG_KEYBOARD_SUN4I_LRADC=y to
sunxi_defconfig. However, it depends on CONFIG_KEYBOARD which is
explicitly disabled in sunxi_defconfig. Hence, the LRADC keys were
never actually enabled. Remove the line disabling CONFIG_KEYBOARD in
order to really enable KEYBOARD_SUN4I_LRADC.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Commit 3d0b16a66c ("nvmem: sunxi: Move the SID driver to the nvmem
framework") moved the the sunxi SID driver to a new framework, but left
sunxi_defconfig with the deprecated config symbol EEPROM_SUNXI_SID
instead of the new symbol NVMEM_SUNXI_SID. Hence, re-enable the driver
in sunxi_defconfig.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
axp20x support has been split into 2 parts, I2C and RSB interface
variants.
Update the MFD_AXP20X symbol for I2C support, and also enable
MFD_AXP20X_RSB to support RSB variants.
Keep MFD_AXP20X enabled for now, to ease migration for automated boot
farms while the patches are being merged. This should be removed in the
next release.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Loadable module support is enabled so we should allow unloading
modules too. This also allows lsmod to show values other than "-2" in
the "Used by" column.
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Defconfig sunxi for Allwinner A10/A20 CAN driver
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable sun6i DMA engine, sun6i P2WI, PWM, and crypto engine (Security
System) drivers by default. EXTCON is needed by the updated sun4i USB
PHY driver.
While at it, enable FHANDLE, which is needed by systemd and newer
versions of udev. Also enable CGROUPS for systemd.
And get rid of POWER_RESET, as the sun6i power reset driver has been
removed in favor of proper sun6i watchdog support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have simplefb support, we can enable it in our defconfig. Also
enable the framebuffer console, so that we are sure that we actually get
something displayed in any case.
And while we're at it, enable the module support.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Commit b2b3a8b934 ("power/reset: Remove sun6i reboot driver") removed
the sun6i reboot driver. But sunxi_defconfig and multi_v7_defconfig
still contain the symbol CONFIG_POWER_RESET_SUN6I that was deprecated
by that commit, so remove it.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The a80 optimus has 8 CPUs. I propose we increase the maximum number of CPUs to 8 to avoid the following warning identified during automated boot testing [1].
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at ../arch/arm/kernel/devtree.c:144 arm_dt_init_cpu_maps+0x110/0x1e0()
DT /cpu 5 nodes greater than max cores 4, capping them
CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-00528-gbdccc4edeb03 #1
Hardware name: Allwinner sun9i Family
[] (unwind_backtrace) from [] (show_stack+0x10/0x14)
[] (show_stack) from [] (dump_stack+0x74/0x90)
[] (dump_stack) from [] (warn_slowpath_common+0x70/0xac)
[] (warn_slowpath_common) from [] (warn_slowpath_fmt+0x30/0x40)
[] (warn_slowpath_fmt) from [] (arm_dt_init_cpu_maps+0x110/0x1e0)
[] (arm_dt_init_cpu_maps) from [] (setup_arch+0x634/0x8d4)
[] (setup_arch) from [] (start_kernel+0x88/0x3ac)
[] (start_kernel) from [<20008074>] (0x20008074)
---[ end trace cb88537fdc8fa200 ]---
[1] http://storage.kernelci.org/mainline/v3.19-528-gbdccc4edeb03/arm-sunxi_defconfig/lab-tbaker/boot-sun9i-a80-optimus.html
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
