Add also the level-shifter flag to avoid probe failure in magnetometer
probe.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-ID: <20230927173245.2151083-4-andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Possibility to use the i2c gate is only for compatibility reasons,
so avoid messing around with additional i2c busses.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-ID: <20230924222718.2038849-1-andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the default MODE setting of a GPIO pin that was missing from the device
tree (i.e. P2.20/gpio2_00). This is to ensure the GPIO pins match the
pocketbeagle wiring expectations.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Message-ID: <20230822143051.7640-5-twoerner@gmail.com>
[tony@atomide.com: leave out extra line break]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that the PRU code is upstream and can be loaded via remoteproc, adjust
the device tree to enable it and adjust the pin muxing so that the default
setting of the pins matches what's is given on the silkscreen and/or
pocketbeagle wiring.
Caveat:
In most cases, the silkscreen will indicate, for example, "PRU0.7",
but it doesn't indicate whether that pin should be enabled for input
or output. On the PRU a different MODE is used for input versus
output. So it is unclear which mode to enable (MODE5 = output, MODE6
= input). In cases where there is a choice (PRU1.11, PRU0.7, PRU0.4,
PRU0.1, PRU1.10, PRU0.6, PRU0.3, PRU0.2, and PRU0.5) output is assumed
(MODE5).
The remaining PRU silkscreen pins do not have a choice and are set as
follows:
PRU0.16 MODE5 input
PRU0.15i MODE6 input
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Message-ID: <20230822143051.7640-4-twoerner@gmail.com>
[tony@atomide.com: formatted description to fit 75 characters]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the self-referenceing "pinctrl-0" entry inside the pinmux clause.
This eliminates the set of boot messages (one for each referenced pin)
similar to the following:
platform 44e10800.pinmux: Fixed dependency cycle(s) with /ocp/interconnect@44c00000/segment@200000/target-module@10000/scm@0/pinmux@800/pinmux_P2_17_gpio
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Message-ID: <20230822143051.7640-3-twoerner@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add LED since the driver is now available.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-ID: <20230819143109.471615-1-andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On mapphone devices we may get lots of noise on the micro-USB port in debug
uart mode until the phy-cpcap-usb driver probes. Let's limit the noise by
using overrun-throttle-ms.
Note that there is also a related separate issue where the charger cable
connected may cause random sysrq requests until phy-cpcap-usb probes that
still remains.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 0840242e88 ("ARM: dts: Configure clock parent for pwm vibra")
attempted to fix the PWM settings but ended up causin an additional clock
reparenting error:
clk: failed to reparent abe-clkctrl:0060:24 to sys_clkin_ck: -22
Only timer9 is in the PER domain and can use the sys_clkin_ck clock source.
For timer8, the there is no sys_clkin_ck available as it's in the ABE
domain, instead it should use syc_clk_div_ck. However, for power
management, we want to use the always on sys_32k_ck instead.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fixes: 0840242e88 ("ARM: dts: Configure clock parent for pwm vibra")
Depends-on: 61978617e9 ("ARM: dts: Add minimal support for Droid Bionic xt875")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix "thermal_sys: cpu_thermal: Failed to read thermal-sensors cells: -2"
error on boot for omap3/4. This is caused by wrong addressing in the dts
for bandgap sensor for single sensor instances.
Note that omap4-cpu-thermal.dtsi is shared across omap4/5 and dra7, so
we can't just change the addressing in omap4-cpu-thermal.dtsi.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fixes: a761d517bb ("ARM: dts: omap3: Add cpu_thermal zone")
Fixes: 0bbf6c54d1 ("arm: dts: add omap4 CPU thermal data")
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are the devicetree updates for Arm and RISC-V based SoCs,
mainly from Qualcomm, NXP/Freescale, Aspeed, TI, Rockchips,
Samsung, ST and Starfive.
Only a few new SoC got added:
- TI AM62P5, a variant of the existing Sitara AM62x family
- Intel Agilex5, an FPGFA platform that includes an
Cortex-A76/A55 SoC.
- Qualcomm ipq5018 is used in wireless access points
- Qualcomm SM4450 (Snapdragon 4 Gen 2) is a new low-end mobile
phone platform.
In total, 29 machines get added, which is low because of the summer
break. These cover SoCs from Aspeed, Broadcom, NXP, Samsung, ST,
Allwinner, Amlogic, Intel, Qualcomm, Rockchip, TI and T-Head. Most of
these are development and reference boards.
Despite not adding a lot of new machines, there are over 700 patches in
total, most of which are cleanups and minor fixes.
-----BEGIN PGP SIGNATURE-----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=bO3j
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"These are the devicetree updates for Arm and RISC-V based SoCs, mainly
from Qualcomm, NXP/Freescale, Aspeed, TI, Rockchips, Samsung, ST and
Starfive.
Only a few new SoC got added:
- TI AM62P5, a variant of the existing Sitara AM62x family
- Intel Agilex5, an FPGFA platform that includes an Cortex-A76/A55
SoC.
- Qualcomm ipq5018 is used in wireless access points
- Qualcomm SM4450 (Snapdragon 4 Gen 2) is a new low-end mobile phone
platform.
In total, 29 machines get added, which is low because of the summer
break. These cover SoCs from Aspeed, Broadcom, NXP, Samsung, ST,
Allwinner, Amlogic, Intel, Qualcomm, Rockchip, TI and T-Head. Most of
these are development and reference boards.
Despite not adding a lot of new machines, there are over 700 patches
in total, most of which are cleanups and minor fixes"
* tag 'soc-dt-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (735 commits)
arm64: dts: use capital "OR" for multiple licenses in SPDX
ARM: dts: use capital "OR" for multiple licenses in SPDX
arm64: dts: qcom: sdm845-db845c: Mark cont splash memory region as reserved
ARM: dts: qcom: apq8064: add support to gsbi4 uart
riscv: dts: change TH1520 files to dual license
riscv: dts: thead: add BeagleV Ahead board device tree
dt-bindings: riscv: Add BeagleV Ahead board compatibles
ARM: dts: stm32: add SCMI PMIC regulators on stm32mp135f-dk board
ARM: dts: stm32: STM32MP13x SoC exposes SCMI regulators
dt-bindings: rcc: stm32: add STM32MP13 SCMI regulators IDs
ARM: dts: stm32: support display on stm32f746-disco board
ARM: dts: stm32: rename mmc_vcard to vcc-3v3 on stm32f746-disco
ARM: dts: stm32: add pin map for LTDC on stm32f7
ARM: dts: stm32: add ltdc support on stm32f746 MCU
arm64: dts: qcom: sm6350: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sdm670: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sa8775p: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sc8280xp: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sdm670: Add PDC
riscv: dts: starfive: fix jh7110 qspi sort order
...
The on-board eeprom on beaglebone series has a power supply from
VDD_3V3A, add that to dts to reduce dummy regulator warning.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Message-ID: <TY3P286MB2611CDC84604B11570B4A8D2980FA@TY3P286MB2611.JPNP286.PROD.OUTLOOK.COM>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds ethernet PHY reset GPIO config for Beaglebone Black
series boards with revision C3. This fixes a random phy startup failure
bug discussed at [1]. The GPIO pin used for reset is not used on older
revisions, so it is ok to apply to all board revisions. The reset timing
was discussed and tested at [2].
[1] https://forum.digikey.com/t/ethernet-device-is-not-detecting-on-ubuntu-20-04-lts-on-bbg/19948
[2] https://forum.beagleboard.org/t/recognizing-a-beaglebone-black-rev-c3-board/31249/
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Message-ID: <TY3P286MB26113797A3B2EC7E0348BBB2980FA@TY3P286MB2611.JPNP286.PROD.OUTLOOK.COM>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the opp table node names for opps to be compliant with bindings.
Signed-off-by: Nishanth Menon <nm@ti.com>
Message-ID: <20230724153911.1376830-4-nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
opp_slow is not defined in the table in dra7 or derivatives, drop the
definition.
Signed-off-by: Nishanth Menon <nm@ti.com>
Message-ID: <20230724153911.1376830-3-nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Each interrupt should be in its own cell. This is much more readable.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Message-ID: <20230730111533.98136-1-krzysztof.kozlowski@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for each
SoC vendor, following the same scheme that is used on arm64, mips and
riscv. This has been discussed for many years, but so far we never did
this as there was a plan to move the files out of the kernel entirely,
which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along
with their device drivers.
* The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the time.
* Amlogic C3 is a Cortex-A35 based smart IP camera chip
* Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
* Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
* Qualcomm SDX75 is the latest generation modem chip that is used
as a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
* Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the Xuantie
C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those included
there are 39 new board files, but only five more 32-bit this time, probably
a new low:
* Marantec Maveo board based on dhcor imx6ull module
* Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
* Epson Moverio BT-200 AR glasses based on TI OMAP4
* PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
* ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than
we had in the recent releases:
* Three boards based on NXP i.MX8: Emtop SoM & Baseboard,
NXP i.MX8MM EVKB board and i.MX8MP based Gateworks Venice
gw7905-2x device.
* NVIDIA IGX Orin and Jetson Orin Nano boards, both based on
tegra234
* Qualcomm gains support for 6 reference boards on various members
of their IPQ networking SoC series, as well as the Sony Xperia M4
Aqua phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board
on top of the various reference platforms for their new chips.
* Rockchips support for several newer boards: Indiedroid Nova (rk3588),
Edgeble Neural Compute Module 6B (rk3588), FriendlyARM NanoPi R2C
Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn Fastrhino R66S/R68S
(rk3568)
* TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex Verdin
family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
* continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
* support for devicetree overlays on at91, bcm283x
* significant additions to existing SoC support on mediatek, qualcomm,
ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST STM32MP1
As usual, a lot more detail is available in the individual merge
commits.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmSdmeUACgkQYKtH/8kJ
UieI5A//bxZXA54htEPXN5V1oIgC4JB4UYkf8fAvtyK4tdaImMn4OTwLD8/sw18X
LQHf1VOLGsGJyNCQ+cUoaBnysr2CXqL/9dA/ARTalqnrKMN/OQjt2wg62n1Ss9Pv
XRlxJABGxAokTO/SuPtOIakSkzwDkuAkIFKfmrNQGcT95XkJXJk3FlMRr84310UG
sl6jP2XFSiLSYm958MMNt+DMhxRmKuyT9gos24KGsb83lZSm9DC2hYimkjd1KF5P
CKeShWeoGoJe+YhnJx6dsDSqVgp1DFLZF1G0auSwjs9rCAKnCDMlz+T2bEzviVDh
XONBNmnOGwPRiBI+1WdzX+pZqMMWINmhIObuODV4ANCSlX3KlSaC2rropEimlW9S
CefvYJ+i7v/BQgMLhKlft0RHhsPU7Pfhfq4PWxaIMAOWA6ZaVczMCpgeUupHIwIQ
lWXZZDlqmTL6SCgkOhEtdP2GGec7YSroq7sscinBaQs1f5pfoW83CNn46gZ9Jh8S
RnXp/+vZ7+RFc15Y0VM82F6a7WN/n0BAqKmqwceDrCpf6ILrBc1lA7NhEvd80wbB
IMg8QNqIzZ9aTOoZmB/1wAXaLClKCE3poTF+Wkd5szN7qe+hKAe1M4w5XvNUO/i/
d0/X5KNA2ykuUxRMdd4lG54VsTJdDCVNaNeaEqasv9JCBBfvuwI=
=X/KE
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for
each SoC vendor, following the same scheme that is used on arm64, mips
and riscv. This has been discussed for many years, but so far we never
did this as there was a plan to move the files out of the kernel
entirely, which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along with
their device drivers.
- The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the
time.
- Amlogic C3 is a Cortex-A35 based smart IP camera chip
- Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
- Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
- Qualcomm SDX75 is the latest generation modem chip that is used as
a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
- Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
Xuantie C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those
included there are 39 new board files, but only five more 32-bit this
time, probably a new low:
- Marantec Maveo board based on dhcor imx6ull module
- Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
- Epson Moverio BT-200 AR glasses based on TI OMAP4
- PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
- ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than we had
in the recent releases:
- Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.
- NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234
- Qualcomm gains support for 6 reference boards on various members of
their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
of the various reference platforms for their new chips.
- Rockchips support for several newer boards: Indiedroid Nova
(rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
Fastrhino R66S/R68S (rk3568)
- TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
Verdin family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
- continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
- support for devicetree overlays on at91, bcm283x
- significant additions to existing SoC support on mediatek,
qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
STM32MP1
As usual, a lot more detail is available in the individual merge
commits"
* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
ARM: mvebu: fix unit address on armada-390-db flash
ARM: dts: Move .dts files to vendor sub-directories
kbuild: Support flat DTBs install
ARM: dts: Add .dts files missing from the build
ARM: dts: allwinner: Use quoted #include
ARM: dts: lan966x: kontron-d10: add PHY interrupts
ARM: dts: lan966x: kontron-d10: fix SPI CS
ARM: dts: lan966x: kontron-d10: fix board reset
ARM: dts: at91: Enable device-tree overlay support for AT91 boards
arm: dts: Enable device-tree overlay support for AT91 boards
arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
ARM: dts: at91: use generic name for shutdown controller
ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
dt-bindings: firmware: brcm,kona-smc: convert to YAML
riscv: dts: sort makefile entries by directory
riscv: defconfig: enable T-HEAD SoC
MAINTAINERS: add entry for T-HEAD RISC-V SoC
riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
riscv: dts: add initial T-HEAD TH1520 SoC device tree
riscv: Add the T-HEAD SoC family Kconfig option
...
The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.
There's no change to dtbs_install as the flat structure is maintained on
install.
The naming of vendor directories is roughly in this order of preference:
- Matching original and current SoC vendor prefix/name (e.g. ti, qcom)
- Current vendor prefix/name if still actively sold (SoCs which have
been aquired) (e.g. nxp/imx)
- Existing platform name for older platforms not sold/maintained by any
company (e.g. gemini, nspire)
The whole move was scripted with the exception of MAINTAINERS and a few
makefile fixups.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com> #Xilinx
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Paul Barker <paul.barker@sancloud.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Wei Xu <xuwei5@hisilicon.com> #hisilicon
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #broadcom
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
