Define the GPIO expander which controls at least some camera gpios.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241010122957.85164-5-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Set them to the state seen in a running system, initialized
by vendor u-boot or kernel. Add line names where they are defined in the
vendor kernel.
gpio15 resets something in the display, otherwise meaning of the
gpios is not known.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241010122957.85164-4-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Wire up the regulators where usage is plausible. Do not
wire them if purpose/usage is unclear like 5V for
many things requiring lower voltages.
Tested on vendor kernel that backlight definitively does not react
on blc_[rl] GPIOs.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241010122957.85164-3-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
To properly have things running after cold boot, define
GPIO regulators. Naming is based on board file.
In the vendor kernel they are enabled in a function
called bt2ws_dcdc_init() if the system is not booted just
to charge the battery.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241010122957.85164-2-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Configure the TWL6032 as system power controller to let the device
power off.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-ID: <20240217082007.3238948-4-andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since the required clock is now available, add bluetooth.
Note: Firmware (bts file) from device vendor reroutes tx for some time
during initialisation and later put it back, producing timeouts in
bluetooth initialisation but ignoring that command leads to proper
initialisation.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-ID: <20231004070309.2408745-1-andreas@kemnade.info>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
WLAN did only work if clock was left enabled by the original system,
so make it fully enable the needed resources itself.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-ID: <20230916100515.1650336-6-andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like one pinctrl single binding warning sneaked in while we were
implementing the yaml binding. Let's fix the 'pinmux-wl12xx-gpio' does not
match any of the regexes warning by adding -pins suffix.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add also the level-shifter flag to avoid probe failure in magnetometer
probe.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-ID: <20230927173245.2151083-4-andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Possibility to use the i2c gate is only for compatibility reasons,
so avoid messing around with additional i2c busses.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-ID: <20230924222718.2038849-1-andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add LED since the driver is now available.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-ID: <20230819143109.471615-1-andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.
There's no change to dtbs_install as the flat structure is maintained on
install.
The naming of vendor directories is roughly in this order of preference:
- Matching original and current SoC vendor prefix/name (e.g. ti, qcom)
- Current vendor prefix/name if still actively sold (SoCs which have
been aquired) (e.g. nxp/imx)
- Existing platform name for older platforms not sold/maintained by any
company (e.g. gemini, nspire)
The whole move was scripted with the exception of MAINTAINERS and a few
makefile fixups.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com> #Xilinx
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Paul Barker <paul.barker@sancloud.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Wei Xu <xuwei5@hisilicon.com> #hisilicon
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #broadcom
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
