Commit b9bf561261 ("ARM: dts: am335x-bone-common: Increase MDIO
reset deassert time") already increased the MDIO reset deassert delay
from 6.5 to 13 ms, but this may still cause Ethernet PHY probe failures:
SMSC LAN8710/LAN8720 4a101000.mdio:00: probe with driver SMSC LAN8710/LAN8720 failed with error -5
On BeagleBone Black Rev. C3, ETH_RESETn is controlled by an open-drain
AND gate. It is pulled high by a 10K resistor, and has a 4.7µF
capacitor to ground, giving an RC time constant of 47ms. As it takes
0.7RC to charge the capacitor above the threshold voltage of a CMOS
input (VDD/2), the delay should be at least 33ms. Considering the
typical tolerance of 20% on capacitors, 40ms would be safer. Add an
additional safety margin and settle for 50ms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/9002a58daa1b2983f39815b748ee9d2f8dcc4829.1730366936.git.geert+renesas@glider.be
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Prior to commit df16c1c51d ("net: phy: mdio_device: Reset device only
when necessary") MDIO reset deasserts were performed twice during boot.
Now that the second deassert is no longer performed, device probe
failures happen due to the change in timing with the following error
message:
SMSC LAN8710/LAN8720: probe of 4a101000.mdio:00 failed with error -5
Restore the original effective timing, which resolves the probe
failures.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://lore.kernel.org/r/20240531183817.2698445-1-colin.foster@in-advantage.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Move the pending urls back to https:// and mark the ones that are no
longer accessible (http or https) as defunct.
Signed-off-by: Nishanth Menon <nm@ti.com>
Message-ID: <20240109195500.3833121-1-nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The on-board eeprom on beaglebone series has a power supply from
VDD_3V3A, add that to dts to reduce dummy regulator warning.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Message-ID: <TY3P286MB2611CDC84604B11570B4A8D2980FA@TY3P286MB2611.JPNP286.PROD.OUTLOOK.COM>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds ethernet PHY reset GPIO config for Beaglebone Black
series boards with revision C3. This fixes a random phy startup failure
bug discussed at [1]. The GPIO pin used for reset is not used on older
revisions, so it is ok to apply to all board revisions. The reset timing
was discussed and tested at [2].
[1] https://forum.digikey.com/t/ethernet-device-is-not-detecting-on-ubuntu-20-04-lts-on-bbg/19948
[2] https://forum.beagleboard.org/t/recognizing-a-beaglebone-black-rev-c3-board/31249/
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Message-ID: <TY3P286MB26113797A3B2EC7E0348BBB2980FA@TY3P286MB2611.JPNP286.PROD.OUTLOOK.COM>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.
There's no change to dtbs_install as the flat structure is maintained on
install.
The naming of vendor directories is roughly in this order of preference:
- Matching original and current SoC vendor prefix/name (e.g. ti, qcom)
- Current vendor prefix/name if still actively sold (SoCs which have
been aquired) (e.g. nxp/imx)
- Existing platform name for older platforms not sold/maintained by any
company (e.g. gemini, nspire)
The whole move was scripted with the exception of MAINTAINERS and a few
makefile fixups.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com> #Xilinx
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Paul Barker <paul.barker@sancloud.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Wei Xu <xuwei5@hisilicon.com> #hisilicon
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #broadcom
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
