Add the pin muxing and GPIO settings for SCL/SDA for i2c2 & i2c3.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the pin muxing and GPIO settings for SCL/SDA for i2c1.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ensure the RTC devices are numbered correctly.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This allows using S10 for power down / shutdown.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I2C expander is capable of generating an IRQ during powersave, so the
attached buttons can be used for waking up the system.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
PCIE_DIS & PCIE_RST (correctly named W_DISABLE# & PERST#) affect USB
devices as well. So hog them to make USB devices attached to Mini PCIe
connector available, despite PCIe being disabled.
Supply voltages are enabled unconditionally.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using internal PHY refclk is not supported yet.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
USB host is an HSIC interface directly connected to a USB hub. USB OTG2
is a direct connection to Mini PCIe interface without any OC signaling.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Split pinctrl as well. 'reset-deassert-us' is added with a small safe
margin.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
make dtbs_check does not warn about this anymore, but bindings mandate
a uint32-matrix.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is one new SoC for each 32-bit Arm and 64-bit RISC-V, but both
the Rockchips rv1109 and Sopgho CV1812H are just minor variations of
already supported chips.
The other six new SoCs are all part of existing arm64 families, but
are somewhat more interesting:
- Samsung ExynosAutov920 is an automotive chip, and the first one
we support based on the Cortex-A78AE core with lockstep mode.
- Google gs101 (Tensor G1) is the chip used in a number of Pixel phones,
and is grouped with Samsung Exynos here since it is based on the same
SoC design, sharing most of its IP blocks with that series.
- MediaTek MT8188 is a new chip used for mid-range tablets and Chromebooks,
using two Cortex-A78 cores where the older MT8195 had four of them.
- Qualcomm SM8650 (Snapdragon 8 Gen 3) is their current top range
phone SoC and the first supported chip based on Cortex-X4, Cortex-A720
and Cortex-A520.
- Qualcomm X1E80100 (Snapdragon X Elite) in turn is the latest
Laptop chip using the custom Oryon cores.
- Unisoc UMS9620 (Tanggula 7 series) is a 5G phone SoC based on
Cortex-A76 and Cortex-A55
In terms of boards, we have
- Five old Microsoft Lumia phones, the HTC One Mini 2, Motorola Moto
G 4G, and Huawei Honor 5X/GR5, all based on Snapdragon SoCs.
- Multiple Rockchips mobile gaming systems (Anbernic RG351V,
Powkiddy RK2023, Powkiddy X55) along with the Sonoff iHost Smart
Home Hub and a few Rockchips SBCs
- Some ComXpress boards based on Marvell CN913x, which is the
follow-up to Armada 7xxx/8xxx.
- Six new industrial/embedded boards based on NXP i.MX8 and i.MX9
- Mediatek MT8183 based Chromebooks from Lenovo, Asus and Acer.
- Toradex Verdin AM62 Mallow carrier for TI AM62
- Huashan Pi board based on the SophGo CV1812H RISC-V chip
- Two boards based on Allwinner H616/H618
- A number of reference boards for various added SoCs from Qualcomm,
Mediatek, Google, Samsung, NXP and Spreadtrum
As usual, there are cleanups and warning fixes across all platforms as
well as added features for several of them.
-----BEGIN PGP SIGNATURE-----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=zR3G
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC DT updates from Arnd Bergmann:
"There is one new SoC for each 32-bit Arm and 64-bit RISC-V, but both
the Rockchips rv1109 and Sopgho CV1812H are just minor variations of
already supported chips.
The other six new SoCs are all part of existing arm64 families, but
are somewhat more interesting:
- Samsung ExynosAutov920 is an automotive chip, and the first one we
support based on the Cortex-A78AE core with lockstep mode.
- Google gs101 (Tensor G1) is the chip used in a number of Pixel
phones, and is grouped with Samsung Exynos here since it is based
on the same SoC design, sharing most of its IP blocks with that
series.
- MediaTek MT8188 is a new chip used for mid-range tablets and
Chromebooks, using two Cortex-A78 cores where the older MT8195 had
four of them.
- Qualcomm SM8650 (Snapdragon 8 Gen 3) is their current top range
phone SoC and the first supported chip based on Cortex-X4,
Cortex-A720 and Cortex-A520.
- Qualcomm X1E80100 (Snapdragon X Elite) in turn is the latest Laptop
chip using the custom Oryon cores.
- Unisoc UMS9620 (Tanggula 7 series) is a 5G phone SoC based on
Cortex-A76 and Cortex-A55
In terms of boards, we have
- Five old Microsoft Lumia phones, the HTC One Mini 2, Motorola Moto
G 4G, and Huawei Honor 5X/GR5, all based on Snapdragon SoCs.
- Multiple Rockchips mobile gaming systems (Anbernic RG351V, Powkiddy
RK2023, Powkiddy X55) along with the Sonoff iHost Smart Home Hub
and a few Rockchips SBCs
- Some ComXpress boards based on Marvell CN913x, which is the
follow-up to Armada 7xxx/8xxx.
- Six new industrial/embedded boards based on NXP i.MX8 and i.MX9
- Mediatek MT8183 based Chromebooks from Lenovo, Asus and Acer.
- Toradex Verdin AM62 Mallow carrier for TI AM62
- Huashan Pi board based on the SophGo CV1812H RISC-V chip
- Two boards based on Allwinner H616/H618
- A number of reference boards for various added SoCs from Qualcomm,
Mediatek, Google, Samsung, NXP and Spreadtrum
As usual, there are cleanups and warning fixes across all platforms as
well as added features for several of them"
* tag 'soc-dt-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (857 commits)
ARM: dts: usr8200: Fix phy registers
arm64: dts: intel: minor whitespace cleanup around '='
arm64: dts: socfpga: agilex: drop redundant status
arm64: dts: socfpga: agilex: add unit address to soc node
arm64: dts: socfpga: agilex: move firmware out of soc node
arm64: dts: socfpga: agilex: move FPGA region out of soc node
arm64: dts: socfpga: agilex: align pin-controller name with bindings
arm64: dts: socfpga: stratix10_swvp: drop unsupported DW MSHC properties
arm64: dts: socfpga: stratix10_socdk: align NAND chip name with bindings
arm64: dts: socfpga: stratix10: add unit address to soc node
arm64: dts: socfpga: stratix10: move firmware out of soc node
arm64: dts: socfpga: stratix10: move FPGA region out of soc node
arm64: dts: socfpga: stratix10: align pincfg nodes with bindings
arm64: dts: socfpga: stratix10: add clock-names to DWC2 USB
arm64: dts: socfpga: drop unsupported cdns,page-size and cdns,block-size
ARM: dts: socfpga: align NAND controller name with bindings
ARM: dts: socfpga: drop unsupported cdns,page-size and cdns,block-size
arm64: dts: rockchip: Fix led pinctrl of lubancat 1
arm64: dts: rockchip: correct gpio_pwrctrl1 typo on nanopc-t6
arm64: dts: rockchip: correct gpio_pwrctrl1 typo on rock-5b
...
Node names should be generic.
Use 'rtc' for the rtc node to fix the following dt-schema warning:
imx27-phytec-phycore-rdk.dtb: pcf8563@51: $nodename:0: 'pcf8563@51' does not match '^rtc(@.*|-([0-9]|[1-9][0-9]+))?$'
from schema $id: http://devicetree.org/schemas/rtc/nxp,pcf8563.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per imx-keypad.yaml, '#address-cells', '#size-cells', 'clock-names'
are not valid properties.
Remove them to fix the following dt-schema warning:
imx25-pdk.dtb: kpp@43fa8000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'clock-names' were unexpected)
from schema $id: http://devicetree.org/schemas/input/imx-keypad.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per leds-gpio.yaml, the led names should start with 'led'.
Change it to fix the following dt-schema warning:
imx27-apf27dev.dtb: leds: 'user' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per display-timings.yaml, the 'timing' pattern should be used to
describe the display timings.
Change it accordingly to fix the following dt-schema warning:
imx27-apf27dev.dtb: display-timings: '800x480' does not match any of the regexes: '^timing', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/panel/display-timings.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per imx-iim.yaml, the compatible string should only contain a single
entry.
Use it as "fsl,imx25-iim" to fix the following dt-schema warning:
imx25-karo-tx25.dtb: efuse@53ff0000: compatible: ['fsl,imx25-iim', 'fsl,imx27-iim'] is too long
from schema $id: http://devicetree.org/schemas/nvmem/imx-iim.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The USB PHY nodes should not be described under 'simple-bus'.
Move it out of simple-bus.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per simple-bus.yaml, 'aipi' is not a valid node name.
Change it to 'bus' to fix the following dt-schema warning:
imx1-apf9328.dtb: aipi@200000: $nodename:0: 'aipi@200000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The USB PHY nodes should not be described under 'simple-bus'.
Move it out of simple-bus.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The USB PHY should not be described under 'simple-bus'.
Move it out of simple-bus.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per simple-bus.yaml, 'emi' is not a valid node name.
Change it to 'bus' to fix the following dt-schema warning:
imx25-pdk.dtb: emi@80000000: $nodename:0: 'emi@80000000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per simple-bus.yaml, 'aipi' is not a valid node name.
Change it to 'bus' to fix the following dt-schema warning:
imx27-pdk.dtb: aipi@10020000: $nodename:0: 'aipi@10020000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to Documentation/devicetree/bindings/sound/imx-audmux.yaml,
there must be a "mux-" prefix in the audmux port nodes.
Add the "mux-" prefix to avoid the following dt-schema warning:
imx27-phytec-phycore-rdk.dtb: audmux@10016000: 'pins4', 'ssi0' do not match any of the regexes: '^mux-[0-9a-z]*$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/sound/imx-audmux.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
The node name should be sram.
Change the node name and pass the required properties to fix the
following dt-schema warnings:
imx1-apf9328.dtb: esram@300000: $nodename:0: 'esram@300000' does not match '^sram(@.*)?'
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#address-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#size-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: 'ranges' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
Pass them to fix the following dt-schema warnings:
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per mtd-physmap.yaml, 'nor@0,0' is not a valid node pattern.
Change it to 'flash@0,0' to fix the following dt-schema warning:
imx1-ads.dtb: nor@0,0: $nodename:0: 'nor@0,0' does not match '^(flash|.*sram|nand)(@.*)?$'
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node names should be generic. Use 'rtc' as node name to fix
the following dt-schema warning:
imx25-eukrea-mbimxsd25-baseboard.dtb: pcf8563@51: $nodename:0: 'pcf8563@51' does not match '^rtc(@.*|-([0-9]|[1-9][0-9]+))?$'
from schema $id: http://devicetree.org/schemas/rtc/nxp,pcf8563.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per sgtl5000.yaml, '#sound-dai-cells' is a required property.
Pass it to fix the following dt-schema warning:
imx25-pdk.dtb: sgtl5000@a: '#sound-dai-cells' is a required property
from schema $id: http://devicetree.org/schemas/sound/sgtl5000.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per i2c-imx.yaml, 'clock-names' is a required property.
Pass it to fix the following dt-schema warning:
imx25-pdk.dtb: i2c@43f80000: clock-names:0: 'ipg' was expected
from schema $id: http://devicetree.org/schemas/i2c/i2c-imx.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The timer nodes declare compatibility with "fsl,imx6sx-gpt", which
itself is compatible with "fsl,imx6dl-gpt". Switch the fallback
compatible from "fsl,imx6sx-gpt" to "fsl,imx6dl-gpt".
Fixes: 9496734502 ("ARM: dts: add imx7d soc dtsi file")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Roland Hieber <rhi@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the device tree support for the MIPI-DSI block. The block can
be used as encoder for the parallel signals coming from the lcdif block.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Roland Hieber <rhi@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The DTS code coding style expects exactly one space before and after '='
sign.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add mmc aliases to ensure a consistent mmc device naming across the
Toradex SoM family, with this commit mmc0 is the on-module eMMC
boot device and the not available mmc interfaces are removed.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add mmc aliases to ensure a consistent mmc device naming across the
Toradex SoM family, with this commit mmc0 is the on-module eMMC
boot device and the not available mmc interfaces are removed.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add mmc aliases to ensure a consistent mmc device naming across the
Toradex SoM family, with this commit mmc0 is the on-module eMMC
boot device and the not available mmc interfaces are removed.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PICO-IMX7D SoM has the usual power supply configuration using
output sw1a of PF3000 PMIC, which was defined in downstream derivative
of linux-imx (see link) in the sources for "Android Things" devkit.
It is required to support CPU frequency scaling.
Map the respective "cpu-supply" nodes of each core to sw1a of the PMIC.
Enabling them causes cpufreq-dt, and imx-thermal drivers to probe
successfully, and CPU frequency scaling to function.
Link: https://android.googlesource.com/platform/hardware/bsp/kernel/nxp/imx-v4.1/+/o-iot-preview-5/arch/arm/boot/dts/imx7d-pico.dtsi#849
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit c7e73b5051 ("ARM: imx: mach-imx6ul: remove 14x14 EVK
specific PHY fixup")thet Ethernet PHY is no longer configured via code
in board file.
This caused Ethernet to stop working.
Fix this problem by describing the clocks and clock-names to the
Ethernet PHY node so that the KSZ8081 chip can be clocked correctly.
Fixes: c7e73b5051 ("ARM: imx: mach-imx6ul: remove 14x14 EVK specific PHY fixup")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
TQMa7x (revision 01xxx) uses a LM75A temperature sensor.
The two sensors use different I2C addresses, so we can set both sensors
simultaneously.
Signed-off-by: João Rodrigues <jrodrigues@ubimet.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Newer variants of Ixora boards require a power-up delay when powering up
the CAN transceiver of up to 1ms.
Cc: stable@vger.kernel.org
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A regression was introduced in the Skov specific i.MX6 flavor
reve-mi1010ait-1cp1 device tree causing the external ethernet controller
to not being selected as the clock source for the i.MX6 ethernet MAC,
resulting in a none functional ethernet interface. The root cause is
that the ethernet clock selection is now part of the clocks node, which
is overwritten in the specific device tree and wasn't updated to contain
these ethernet clocks.
Fixes: c89614079e ("ARM: dts: imx6qdl-skov-cpu: configure ethernet reference clock parent")
Signed-off-by: Stefan Kerkmann <s.kerkmann@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the rx/tx DMA channels for CSPI peripherals. Channel numbers
are taken from i.MX7D RM Rev1 01/2018.
Peripheral types ID (7) is selected according to fsl,imx-sdma.yaml and
is similar to i.MX6 and i.MX8M platforms. Same goes for transfer
priority ID (last number).
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx-thermal.yaml is referencing thermal-sensor.yaml, thus this property
is required. Fixes the dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx7d-mba7.dtb: tempmon:
'#thermal-sensor-cells' is a required property
from schema $id: http://devicetree.org/schemas/thermal/imx-thermal.yaml#
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
nand-controller.yaml bindings says #size-cells shall be set to 0.
Fixes the dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx7s-mba7.dtb: nand-controller@33002000:
#size-cells:0:0: 0 was expected
from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml#
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7d-lcdif is compatible to imx6sx-lcdif. MXSFB_V6 supports overlay
by using LCDC_AS_CTRL register. This registers used by overlay plane:
* LCDC_AS_CTRL
* LCDC_AS_BUF
* LCDC_AS_NEXT_BUF
are listed in i.MX7D RM as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7d uses two ports for 'in-ports', so the syntax port@<num> has to
be used. imx7d has both port and port@1 nodes present, raising these
error:
funnel@30041000: in-ports: More than one condition true in oneOf schema
funnel@30041000: Unevaluated properties are not allowed
('in-ports' was unexpected)
Fix this by also using port@0 for imx7s as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx7d-pico-pi board does not have an SD card slot
connected to the USDHC1 port. Only eMMC and Wifi SDIO ports
are used.
Disable the USDHC1 node.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per fsl,imx-gpcv2.yaml, '#power-domain-cells' is not a valid
property for the top-level gpcv2 node. It is only valid
for its children nodes.
Remove it to fix the following schema warning:
gpc@303a0000: '#power-domain-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/power/fsl,imx-gpcv2.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per fsl-imx-wdt, 'clock-names' is not a valid property.
Remove it to fix the following schema warning:
watchdog@53fdc000: Unevaluated properties are not allowed ('clock-names' was unexpected)
from schema $id: http://devicetree.org/schemas/watchdog/fsl-imx-wdt.yaml
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
Pass them to fix the following schema warnings:
sram@78000000: '#address-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
sram@78000000: '#size-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
sram@78000000: 'ranges' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per imxdi-rtc.yaml, there is only one valid compatible entry and
clock-names is not a valid property.
Change it to fix the following schema warnings:
dryice@53ffc000: compatible: ['fsl,imx25-dryice', 'fsl,imx25-rtc'] is too long
from schema $id: http://devicetree.org/schemas/rtc/imxdi-rtc.yaml#
dryice@53ffc000: 'clock-names' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/rtc/imxdi-rtc.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node names should be generic, so use 'eeprom' to fix the
following schema warnings:
at24@52: $nodename:0: 'at24@52' does not match '^eeprom@[0-9a-f]{1,2}$'
from schema $id: http://devicetree.org/schemas/eeprom/at24.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per fsl-imx-sahara.yaml, there should not be a 'fsl,imx51-sahara'
compatible.
Remove it to fix the following schema warning:
imx51-apf51.dtb: crypto@83ff8000: compatible: ['fsl,imx53-sahara', 'fsl,imx51-sahara'] is too long
from schema $id: http://devicetree.org/schemas/crypto/fsl-imx-sahara.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per fsl-imx-cspi.yaml, "fsl,imx53-ecspi" should not contain addtional
compatible entries.
Change it accordingly to fix the following schema warning:
spi@63fac000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx53-ecspi', 'fsl,imx51-ecspi'] is too long
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per fsl,mxs-usbphy.yaml, fsl,imx7ulp-usbphy is not compatible
with fsl,imx6ul-usbphy.
Remove 'fsl,imx6ul-usbphy' from the compatible string to fix the
following schema warning:
imx7ulp-com.dtb: usb-phy@40350000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx7ulp-usbphy', 'fsl,imx6ul-usbphy'] is too long
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Passing 5 to fsl,tx-d-cal is not valid as per fsl,mxs-usbphy.yaml:
imx6q-pistachio.dtb: usbphy@20c9000: fsl,tx-d-cal:0:0: 5 is less than the minimum of 79
from schema $id: http://devicetree.org/schemas/phy/fsl,mxs-usbphy.yaml#
Pass the minimum value of 79 instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Passing 55 to fsl,tx-cal-45-dn-ohms is not valid as per fsl,mxs-usbphy.yaml:
imx6q-b650v3.dtb: usbphy@20c9000: fsl,tx-cal-45-dn-ohms:0:0: 55 is greater than the maximum of 54
from schema $id: http://devicetree.org/schemas/phy/fsl,mxs-usbphy.yaml#
Pass the maximum value of 54 instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds support for the Variscite MX6 SoM Carrier Board.
This Carrier-Board has the following :
- LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch display
- HDMI Connector
- USB Host + USB OTG Connector
- 10/100/1000 Mbps Ethernet
- miniPCI-Express slot
- SD Card connector
- Audio Headphone/Line In jack connectors
- S-ATA
- On-board DMIC
- RS485 Header
- CAN bus header
- SPI header
- Camera Interfaces header
- OnBoard RTC with Coin Backup battery socket
- RS232 Debug Header (IDC10)
- RS232 DTE
Product Page : https://www.variscite.com/product/single-board-computers/var-mx6customboard
The dts file based on the ones provided by Variscite on their own
kernel, but adapted for mainline.
Cc: Pierluigi Passaro <pierluigi.p@variscite.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds support for the Variscite VAR_SOM-MX6 SoM with :
- i.MX6 Quad or Dual Lite SoC
- 256 – 4096 MB DDR3
- 4-64 GB eMMC
- 128 – 1024 MB SLC NAND
- Camera Interface
- HDMI+CEC interface
- LVDS / DSI / Parallel RGB interfaces
- Ethernet RGMII interface
- On-SoM Wi-Fi/Bluetooth with WiLink wl183x SDIO Module
- SD/MMC/SDIO interface
- USB Host + USB OTG interface
- I2C interfaces
- SPI interfaces
- PCI-Express 2.0 interface
- on-SoM Audio Codec with HP/Line-In interfaces + DMIC interface
- Digital Audio interface
- S/PDIF interface
Product website : https://www.variscite.com/product/system-on-module-som/cortex-a9/var-som-mx6-cpu-freescale-imx6/
Support is handled with a SoM-centric dtsi exporting the default interfaces
along the default pinmuxing to be enabled by the board dts file.
This file is based on the one provided by Variscite on their own
kernel, but adapted for mainline.
Cc: Pierluigi Passaro <pierluigi.p@variscite.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the imx6ull/7d-colibri devicetrees as per the rules defined
at fsl.yaml.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per fsl.yaml, the order of the compatible strings are not correct for
imx6ull-phytec-tauri-emmc and imx6ull-phytec-tauri-nand.
Fix them accordingly.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx6ull-phytec-tauri.dtsi file is included in two places:
imx6ull-phytec-tauri-emmc.dts
imx6ull-phytec-tauri-nand.dts
These two files overwrite the board model and compatible locally, so
there is no need for describing them in imx6ull-phytec-tauri.dtsi.
Remove the board model and compatible.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per nxp,imx7-csi.yaml, there is only one CSI clock entry.
Fix it.
This fixes the following schema warnings:
imx7d-zii-rpu2.dtb: csi@30710000: clocks: [[1, 413], [1, 326], [1, 413]] is too long
from schema $id: http://devicetree.org/schemas/media/nxp,imx7-csi.yaml#
imx7d-zii-rpu2.dtb: csi@30710000: clock-names:0: 'mclk' was expected
from schema $id: http://devicetree.org/schemas/media/nxp,imx7-csi.yaml#
imx7d-zii-rpu2.dtb: csi@30710000: clock-names: ['axi', 'mclk', 'dcic'] is too long
from schema $id: http://devicetree.org/schemas/media/nxp,imx7-csi.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 'gpios' property to describe the SDA and SCL GPIOs is considered
deprecated according to i2c-gpio.yaml.
Switch to the preferred 'sda-gpios' and 'scl-gpios' properties.
This fixes the following schema warnings:
imx51-zii-rdu1.dtb: i2c-gpio: 'sda-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
imx51-zii-rdu1.dtb: i2c-gpio: 'scl-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 'gpios' property to describe the SDA and SCL GPIOs is considered
deprecated according to i2c-gpio.yaml.
Switch to the preferred 'sda-gpios' and 'scl-gpios' properties.
This fixes the following schema warnings:
imx6ul-tx6ul-0011.dtb: i2c-gpio: 'sda-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
imx6ul-tx6ul-0011.dtb: i2c-gpio: 'scl-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to st,st-sensors.yaml, the 'interrupt-names' property is
not a valid one.
Remove it to fix the following schema warnings:
imx6dl-gw5912.dtb: accel@19: 'interrupt-names' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/iio/st,st-sensors.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Complete the switch definition by adding the internal mdio nodes.
This does not change behavior on Linux but is required if the dt is used
for U-Boot which requires the internal PHY ports to be defined for
DSA.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SK-ATM0700D4-Plug is an extension board (provided by the same
manufacturer, [1]) which can be connected to the SK-IMX53 panel kit. The
panel can be connected either using the RGB parallel bus or using the
LVDS connector (recommended). Add DT files describing this "shield",
both RGB and LVDS connections.
[1] http://starterkit.ru/html/index.php?name=shop&op=view&id=64
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Root node is not a bus, thus top-level nodes do not have unit addresses.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Numbers are separated by dashes. Fixes the warnings:
arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2-mba6ulx.dtb: gpio-keys:
'button1', 'button2', 'button3' do not match any of the regexes:
'^(button|event|key|switch|(button|event|key|switch)-[a-z0-9-]+|[a-z0-9-]+-(button|event|key|switch))$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/input/gpio-keys.yaml#
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I2C expander is capable of generating an IRQ during powersave, so the
attached buttons can be used for waking up the system.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These are the devicetree updates for Arm and RISC-V based SoCs,
mainly from Qualcomm, NXP/Freescale, Aspeed, TI, Rockchips,
Samsung, ST and Starfive.
Only a few new SoC got added:
- TI AM62P5, a variant of the existing Sitara AM62x family
- Intel Agilex5, an FPGFA platform that includes an
Cortex-A76/A55 SoC.
- Qualcomm ipq5018 is used in wireless access points
- Qualcomm SM4450 (Snapdragon 4 Gen 2) is a new low-end mobile
phone platform.
In total, 29 machines get added, which is low because of the summer
break. These cover SoCs from Aspeed, Broadcom, NXP, Samsung, ST,
Allwinner, Amlogic, Intel, Qualcomm, Rockchip, TI and T-Head. Most of
these are development and reference boards.
Despite not adding a lot of new machines, there are over 700 patches in
total, most of which are cleanups and minor fixes.
-----BEGIN PGP SIGNATURE-----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=bO3j
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"These are the devicetree updates for Arm and RISC-V based SoCs, mainly
from Qualcomm, NXP/Freescale, Aspeed, TI, Rockchips, Samsung, ST and
Starfive.
Only a few new SoC got added:
- TI AM62P5, a variant of the existing Sitara AM62x family
- Intel Agilex5, an FPGFA platform that includes an Cortex-A76/A55
SoC.
- Qualcomm ipq5018 is used in wireless access points
- Qualcomm SM4450 (Snapdragon 4 Gen 2) is a new low-end mobile phone
platform.
In total, 29 machines get added, which is low because of the summer
break. These cover SoCs from Aspeed, Broadcom, NXP, Samsung, ST,
Allwinner, Amlogic, Intel, Qualcomm, Rockchip, TI and T-Head. Most of
these are development and reference boards.
Despite not adding a lot of new machines, there are over 700 patches
in total, most of which are cleanups and minor fixes"
* tag 'soc-dt-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (735 commits)
arm64: dts: use capital "OR" for multiple licenses in SPDX
ARM: dts: use capital "OR" for multiple licenses in SPDX
arm64: dts: qcom: sdm845-db845c: Mark cont splash memory region as reserved
ARM: dts: qcom: apq8064: add support to gsbi4 uart
riscv: dts: change TH1520 files to dual license
riscv: dts: thead: add BeagleV Ahead board device tree
dt-bindings: riscv: Add BeagleV Ahead board compatibles
ARM: dts: stm32: add SCMI PMIC regulators on stm32mp135f-dk board
ARM: dts: stm32: STM32MP13x SoC exposes SCMI regulators
dt-bindings: rcc: stm32: add STM32MP13 SCMI regulators IDs
ARM: dts: stm32: support display on stm32f746-disco board
ARM: dts: stm32: rename mmc_vcard to vcc-3v3 on stm32f746-disco
ARM: dts: stm32: add pin map for LTDC on stm32f7
ARM: dts: stm32: add ltdc support on stm32f746 MCU
arm64: dts: qcom: sm6350: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sdm670: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sa8775p: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sc8280xp: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sdm670: Add PDC
riscv: dts: starfive: fix jh7110 qspi sort order
...
Documentation/process/license-rules.rst and checkpatch expect the SPDX
identifier syntax for multiple licenses to use capital "OR". Correct it
to keep consistent format and avoid copy-paste issues.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230823085146.113562-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Numbers are separated by dashes. Fixes the warnings:
arch/arm/boot/dts/nxp/imx/imx6q-mba6a.dtb: gpio-buttons: 'button1',
'button2', 'button3' do not match any of the regexes:
'^(button|event|key|switch|(button|event|key|switch)-[a-z0-9-]+|[a-z0-9-]+-(button|event|key|switch))$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/input/gpio-keys.yaml#
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
nand-controller.yaml bindings says #size-cells shall be set to 0.
Fixes the dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2l-mba6ulx.dtb:
nand-controller@1806000: #size-cells:0:0: 0 was expected
from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml#
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
interrupt-controller is only valid for gpio subnode, remove it.
Rename touchscreen subnode according to bindings.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per simple-card.yaml, 'simple-audio-card,audio-routing' is not a valid
property.
Change it to 'simple-audio-card,routing'.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Wifi chip description, which causes the following schema warning:
imx6q-prti6q.dtb: mmc@2194000: Unevaluated properties are not allowed ('wifi' was unexpected)
Pass the missing items to fix it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"st,m25p" is not a valid compatible according to jedec,spi-nor.yaml.
Remove it.
Also, node names should be generic, so use 'flash' as the SPI NOR flash
node name.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node names should be generic, so use 'flash' as the SPI NOR flash node
name.
This fixes the following schema warning:
imx53-smd.dtb: m25p32@1: $nodename:0: 'm25p32@1' does not match '^(flash|.*sram|nand)(@.*)?$'
from schema $id: http://devicetree.org/schemas/mtd/jedec,spi-nor.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"st,m25p" is not a valid compatible according to jedec,spi-nor.yaml.
Remove it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Passing the 'compatible' property inside the pfuze100 regulator nodes
is not allowed per pfuze100.yaml and results in the following
warning:
imx6q-bosch-acc.dtb: pmic@8: regulators:sw3a: Unevaluated properties are not allowed ('compatible' was unexpected)
Remove it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As per sgtl5000.yaml, '#sound-dai-cells' is a required property.
Pass it to fix the following schema warnings:
imx53-mba53.dtb: sgtl5000@a: '#sound-dai-cells' is a required property
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As per sgtl5000.yaml, 'clock-names' is not a valid property.
Remove it to fix the following schema warning:
imx6ul-isiot-nand.dtb: codec@a: Unevaluated properties are not allowed ('clock-names' was unexpected)
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
If the tuning step is not set, the tuning step is set to 1.
For some sd cards, the following Tuning timeout will occur.
Tuning failed, falling back to fixed sampling clock
So set the default tuning step. This refers to the NXP vendor's
commit below:
https://github.com/nxp-imx/linux-imx/blob/lf-6.1.y/
arch/arm/boot/dts/imx6sx.dtsi#L1108-L1109
Fixes: 1e336aa0c0 ("mmc: sdhci-esdhc-imx: correct the tuning start tap and step setting")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fixed regulators are not in some bus and bindings do not allow a "reg"
property. Move them out of "regulators" node to top-level.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fixed regulators are not in some bus and bindings do not allow a "reg"
property. Move them out of "regulators" node to top-level.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The recommended name for enable GPIOs property in regulator-gpio is
"enable-gpios". This is also required by bindings:
imx50-kobo-aura.dtb: gpio-regulator: Unevaluated properties are not allowed ('enable-gpio' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
regulator-fixed-clock does not take "regulator-type" property:
imx6ull-colibri-iris-v2.dtb: regulator-eth-phy: Unevaluated properties are not allowed ('regulator-type' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
regulator-fixed does not take "clock-names" property:
imx6sx-nitrogen6sx.dtb: regulator-wlan: Unevaluated properties are not allowed ('clock-names' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
MX53_PAD_GPIO_1__PWM2_PWMO controls the backlight of the parallel
Seiko display and MX53_PAD_EIM_D24__GPIO3_24 controls the display power.
Reflect that in the devicetree for better description of the board.
Without these entries there is no LCD output on the Seiko display, unless
the bootloader has previously configured these pins.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
If the tuning step is not set, the tuning step is set to 1.
For some sd cards, the following Tuning timeout will occur.
Tuning failed, falling back to fixed sampling clock
mmc0: Tuning failed, falling back to fixed sampling clock
So set the default tuning step. This refers to the NXP vendor's
commit below:
https://github.com/nxp-imx/linux-imx/blob/lf-6.1.y/
arch/arm/boot/dts/imx7s.dtsi#L1216-L1217
Fixes: 1e336aa0c0 ("mmc: sdhci-esdhc-imx: correct the tuning start tap and step setting")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fixes the warning:
lm75 0-0048: supply vs not found, using dummy regulator
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Due to the missing signal connection between i.MX6 WDOG_B pin and the
PMICs external reset, the internal i.MX6 watchdog is not able to reset
the phyCORE i.MX6 SoM properly. Thus disable the internal i.MX6 watchdog
to prevent unexpected PMIC settings after reset.
NOTE: This patch should not be backported as it might break existing
uses and fixes in bootloaders.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Stefan Riedmüller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Due to the missing signal connection between i.MX6 WDOG_B pin and the
PMICs external reset, the internal i.MX6 watchdog is not able to reset
the phyFLEX SoM properly. Thus disable the internal i.MX6 watchdog to
prevent unexpected PMIC settings after reset.
NOTE: This patch should not be backported as it might break existing
uses and fixes in bootloaders.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Stefan Riedmüller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RTC interrupt level should be set to "LOW". This was revealed by the
introduction of commit:
f181987ef4 ("rtc: m41t80: use IRQ flags obtained from fwnode")
which changed the way IRQ type is obtained.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Stefan Riedmüller <s.riedmueller@phytec.de>
Fixes: 800d595151 ("ARM: dts: imx6: Add initial support for phyBOARD-Mira")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A suitable default for the LCDIF parent is the PLL5 clock, so
describe it in the device tree.
The imx6sx clock driver harcodes PLL5 as the LCDIF1 parent, but
in preparation for removing such hardcoding, describe the parent
relationship via devicetree.
There are some boards that may want to use a different parent
for the LCDIF due to EMI reasons, for example.
With this approch, the user can change the LCDIF parent in the board
devicetree if needed.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the LDB endpoint description from the common imx6sx.dtsi
as it causes regression for boards that has the LCDIF connected
directly to a parallel display.
Let the LDB endpoint be described in the board devicetree file
instead.
Cc: stable@vger.kernel.org
Fixes: b74edf626c ("ARM: dts: imx6sx: Add LDB support")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fixes the warnings:
at24 0-0057: supply vcc not found, using dummy regulator
lm75 0-0049: supply vs not found, using dummy regulator
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Describe the Ethernet aliases so that the second MAC address
can be retrieved from the bootloader.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Regulators should not be placed under simple-bus.
Move it outside simple-bus to fix the following schema warnings:
regulators: $nodename:0: 'regulators' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
From schema: site-packages/dtschema/schemas/simple-bus.yaml
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SK-IMX53 board, bearing i.MX536A CPU, is not stable when running at
1.2 GHz (default iMX53 maximum). The SoC is only rated up to 800 MHz.
Disable 1.2 GHz and 1 GHz frequencies.
Fixes: 0b8576d844 ("ARM: dts: imx: Add support for SK-iMX53 board")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Property name "phy-3p0-supply" is used instead of "phy-reg_3p0-supply".
Fixes: 9f30b6b1a9 ("ARM: dts: imx: Add basic dtsi file for imx6sll")
cc: <stable@vger.kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Instead of using 0x80000000 explicitly specify the reset defaults for
the pad settings. This way the pad configuration is explicit and so
isn't affected by changes that might have been done in the bootloader.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for each
SoC vendor, following the same scheme that is used on arm64, mips and
riscv. This has been discussed for many years, but so far we never did
this as there was a plan to move the files out of the kernel entirely,
which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along
with their device drivers.
* The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the time.
* Amlogic C3 is a Cortex-A35 based smart IP camera chip
* Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
* Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
* Qualcomm SDX75 is the latest generation modem chip that is used
as a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
* Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the Xuantie
C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those included
there are 39 new board files, but only five more 32-bit this time, probably
a new low:
* Marantec Maveo board based on dhcor imx6ull module
* Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
* Epson Moverio BT-200 AR glasses based on TI OMAP4
* PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
* ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than
we had in the recent releases:
* Three boards based on NXP i.MX8: Emtop SoM & Baseboard,
NXP i.MX8MM EVKB board and i.MX8MP based Gateworks Venice
gw7905-2x device.
* NVIDIA IGX Orin and Jetson Orin Nano boards, both based on
tegra234
* Qualcomm gains support for 6 reference boards on various members
of their IPQ networking SoC series, as well as the Sony Xperia M4
Aqua phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board
on top of the various reference platforms for their new chips.
* Rockchips support for several newer boards: Indiedroid Nova (rk3588),
Edgeble Neural Compute Module 6B (rk3588), FriendlyARM NanoPi R2C
Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn Fastrhino R66S/R68S
(rk3568)
* TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex Verdin
family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
* continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
* support for devicetree overlays on at91, bcm283x
* significant additions to existing SoC support on mediatek, qualcomm,
ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST STM32MP1
As usual, a lot more detail is available in the individual merge
commits.
-----BEGIN PGP SIGNATURE-----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=X/KE
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for
each SoC vendor, following the same scheme that is used on arm64, mips
and riscv. This has been discussed for many years, but so far we never
did this as there was a plan to move the files out of the kernel
entirely, which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along with
their device drivers.
- The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the
time.
- Amlogic C3 is a Cortex-A35 based smart IP camera chip
- Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
- Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
- Qualcomm SDX75 is the latest generation modem chip that is used as
a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
- Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
Xuantie C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those
included there are 39 new board files, but only five more 32-bit this
time, probably a new low:
- Marantec Maveo board based on dhcor imx6ull module
- Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
- Epson Moverio BT-200 AR glasses based on TI OMAP4
- PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
- ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than we had
in the recent releases:
- Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.
- NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234
- Qualcomm gains support for 6 reference boards on various members of
their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
of the various reference platforms for their new chips.
- Rockchips support for several newer boards: Indiedroid Nova
(rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
Fastrhino R66S/R68S (rk3568)
- TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
Verdin family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
- continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
- support for devicetree overlays on at91, bcm283x
- significant additions to existing SoC support on mediatek,
qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
STM32MP1
As usual, a lot more detail is available in the individual merge
commits"
* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
ARM: mvebu: fix unit address on armada-390-db flash
ARM: dts: Move .dts files to vendor sub-directories
kbuild: Support flat DTBs install
ARM: dts: Add .dts files missing from the build
ARM: dts: allwinner: Use quoted #include
ARM: dts: lan966x: kontron-d10: add PHY interrupts
ARM: dts: lan966x: kontron-d10: fix SPI CS
ARM: dts: lan966x: kontron-d10: fix board reset
ARM: dts: at91: Enable device-tree overlay support for AT91 boards
arm: dts: Enable device-tree overlay support for AT91 boards
arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
ARM: dts: at91: use generic name for shutdown controller
ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
dt-bindings: firmware: brcm,kona-smc: convert to YAML
riscv: dts: sort makefile entries by directory
riscv: defconfig: enable T-HEAD SoC
MAINTAINERS: add entry for T-HEAD RISC-V SoC
riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
riscv: dts: add initial T-HEAD TH1520 SoC device tree
riscv: Add the T-HEAD SoC family Kconfig option
...
The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.
There's no change to dtbs_install as the flat structure is maintained on
install.
The naming of vendor directories is roughly in this order of preference:
- Matching original and current SoC vendor prefix/name (e.g. ti, qcom)
- Current vendor prefix/name if still actively sold (SoCs which have
been aquired) (e.g. nxp/imx)
- Existing platform name for older platforms not sold/maintained by any
company (e.g. gemini, nspire)
The whole move was scripted with the exception of MAINTAINERS and a few
makefile fixups.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com> #Xilinx
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Paul Barker <paul.barker@sancloud.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Wei Xu <xuwei5@hisilicon.com> #hisilicon
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #broadcom
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
