* 'clk-3.7' of git://git.linaro.org/people/mturquette/linux:
clk: add of_clk_src_onecell_get() support
clk: ux500: Define smp_twd clock for u8500
mfd: dbx500: Provide a more accurate smp_twd clock
clk: ux500: Support for prmcu_rate clock
clk: Provide option for clk_get_rate to issue hw for new rate
clock: max77686: Add driver for Maxim 77686 32Khz crystal oscillator.
ARM: ux500: Switch to use common clock framework
clk: ux500: Clock definitions for u8500
clk: ux500: First version of clock definitions for ux500
clk: ux500: Adapt PRCMU and PRCC clocks for common clk
clk: versatile: make config option boolean
clk: add Loongson1B clock support
arm: mmp: make all SOCs use common clock by default
clk: mmp: add clock definition for mmp2
clk: mmp: add clock definition for pxa910
clk: mmp: add clock definition for pxa168
clk: mmp: add mmp specific clocks
clk: convert ARM RealView to common clk
clk: prima2: move from arch/arm/mach to drivers/clk
ARM: PRIMA2: convert to common clk and finish full clk tree
Pull DMA-mapping fixes from Marek Szyprowski:
"Another set of fixes for ARM dma-mapping subsystem.
Commit e9da6e9905 replaced custom consistent buffer remapping code
with generic vmalloc areas. It however introduced some regressions
caused by limited support for allocations in atomic context. This
series contains fixes for those regressions.
For some subplatforms the default, pre-allocated pool for atomic
allocations turned out to be too small, so a function for setting its
size has been added.
Another set of patches adds support for atomic allocations to
IOMMU-aware DMA-mapping implementation.
The last part of this pull request contains two fixes for Contiguous
Memory Allocator, which relax too strict requirements."
* 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: IOMMU allocates pages from atomic_pool with GFP_ATOMIC
ARM: dma-mapping: Introduce __atomic_get_pages() for __iommu_get_pages()
ARM: dma-mapping: Refactor out to introduce __in_atomic_pool
ARM: dma-mapping: atomic_pool with struct page **pages
ARM: Kirkwood: increase atomic coherent pool size
ARM: DMA-Mapping: print warning when atomic coherent allocation fails
ARM: DMA-Mapping: add function for setting coherent pool size from platform code
ARM: relax conditions required for enabling Contiguous Memory Allocator
mm: cma: fix alignment requirements for contiguous regions
Even though system suspend/resume hasn't been validated on Tegra yet,
this Kconfig option needs to be enabled so that system shutdown is
reliable on an SMP system. Without it, I2C interrupts may be routed
to CPU0, whereas shutdown code may be running on CPU1, causing I2C
timeouts, preventing communication with the external PMIC.
This reverts 3d5e8af "ARM: disable SUSPEND/ARCH_SUSPEND_POSSIBLE for
ARCH_TEGRA".
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch converts tegra clock code to generic clock framework in following way:
- Implement clk_ops as required by generic clk framework. (tegraXX_clocks.c)
- Use platform specific struct clk_tegra in clk_ops implementation instead of struct clk.
- Initialize all clock data statically. (tegraXX_clocks_data.c)
Legacy framework did not have recalc_rate and is_enabled functions. Implemented these functions.
Removed init function. It's functionality is splitted into recalc_rate and is_enabled.
Static initialization is used since slab is not up in .init_early and clock
is needed to be initialized before clockevent/clocksource initialization.
Macros redefined for clk_tegra.
Also, single struct clk_tegra is used for all type of clocks (PLL, peripheral etc.). This
is to move quickly to generic common clock framework so that other dependent features will
not be blocked (such as DT binding).
Enabling COMMON_CLOCK config moved to ARCH_TEGRA since it is enabled for both Tegra20
and Tegra30.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Removes the pnx4008 platform support, which hasn't seen any active
development since 2006 and seems to be unused these days.
* 'pnx4008-removal' of git://git.antcom.de/linux-2.6:
ARM: mach-pnx4008: Remove architecture
it to use generic time and clock events.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=6GPY
-----END PGP SIGNATURE-----
Merge tag 'ks8695-time-for-arm-soc' of http://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/cleanup
This cleans up the ks8695 timer driver and converts
it to use generic time and clock events.
* tag 'ks8695-time-for-arm-soc' of http://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ks8695: convert to generic time and clocksource
ARM: ks8695: delete resume hook from timer
ARM: ks8695: use [readl|writel]_relaxed()
ARM: ks8695: merge the timer header into the timer driver
Old platforms using ancient gettimeoffset() and other arcane
APIs are standing in the way of cleaning up the ARM kernel.
The gettimeoffset() was also broken: it would try to read out
the timer counter value, while this would not work (the
counter statically returns the initially programmed value)
so the implementation would anyway fall back to a homebrew
version of jiffie calculation.
This is an attempt at blind-coding a generic time and clocksource
driver for the platform by way of a datasheet and looking at the
old code.
Tested-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
big.LITTLE support in the future. The separation of CPU and PMU code
is also the start of being able to move some of this stuff under
drivers/.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vfXN
-----END PGP SIGNATURE-----
Merge tag 'arm-perf-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into next/cleanup
From Will Deacon:
Bunch of perf updates for the ARM backend that pave the way for
big.LITTLE support in the future. The separation of CPU and PMU code
is also the start of being able to move some of this stuff under
drivers/.
* tag 'arm-perf-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux:
ARM: perf: move irq registration into pmu implementation
ARM: perf: move CPU-specific PMU handling code into separate file
ARM: perf: prepare for moving CPU PMU code into separate file
ARM: perf: probe devicetree in preference to current CPU
ARM: perf: remove mysterious compiler barrier
ARM: pmu: remove arm_pmu_type enumeration
ARM: pmu: remove unused reservation mechanism
ARM: perf: add devicetree bindings for 11MPcore, A5, A7 and A15 PMUs
ARM: PMU: Add runtime PM Support
* 'marco-prepare' of git://gitorious.org/sirfprima2-kernel/sirfprima2-kernel:
ARM: SIRF: make sirf irqchip driver optional since new SoCs will have GIC
ARM: PRIMA2: adjust Kconfig to support select SoC features
ARM: PRIMA2: use DT_MACHINE_START and convert to generic board
clk: prima2: move from arch/arm/mach to drivers/clk
ARM: PRIMA2: convert to common clk and finish full clk tree
The io-pci series has gained a merge to resolve a nontrivial
conflict.
* cleanup/io-pci:
ARM: Fix ioremap() of address zero
Also includes an update to Linux 3.6-rc3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As Stephen Rothwell reports, a849088aa1 ("ARM: Fix ioremap() of
address zero") from the arm-current tree and commit c279443709 ("ARM:
Add fixed PCI i/o mapping") from the arm-soc tree conflict in
a nontrivial way in arch/arm/mm/mmu.c.
Rob Herring explains:
The PCI i/o reserved area has a dummy physical address of 0 and
needs to be skipped by ioremap searches. So we don't set
VM_ARM_STATIC_MAPPING to prevent matches by ioremap. The vm_struct
settings don't really matter when we do the real mapping of the
i/o space.
Since commit a849088aa1 is at the start of the fixes branch
in the arm tree, we can merge it into the branch that contains
the other ioremap changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Now that ATAGS support is well contained, we can easily remove it from
the kernel build if so desired. It has to explicitly be disabled, and
only when DT support is selected.
Note: disabling kernel ATAGS support does not prevent the usage of
CONFIG_ARM_ATAG_DTB_COMPAT.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This converts the Nomadik to using pin control using the
driver for the STN8815 ASIC.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With icoll and gpio interrupt controllers adopt irqdomain support and
all interrupt nubmers are retrieved from device tree, it's safe to
select SPARSE_IRQ for mxs now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
As part of multi-platform effort, let's enable MULTI_IRQ_HANDLER for
mach-mxs and remove entry-macro.S.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Contiguous Memory Allocator requires only paging and MMU enabled not
particular CPU architectures, so there is no need for strict dependency
on CPU type. This enables to use CMA on some older ARM v5 systems which
also might need large contiguous blocks for the multimedia processing hw
modules.
Reported-by: Prabhakar Lad <prabhakar.lad@ti.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Prabhakar Lad <prabhakar.lad@ti.com>
Now we have primaII, but will include Marco and Polo in mach-prima2
as well. We add Kconfig menu so that we can select necessary SoC
features.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
This patch removes the ARM architecture mach-pnx4008. No direct support or user
feedback since 2006. Acknowledgements from NXP/Philips and Linux arm-soc
maintainers.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Bug fixes for various ARM platforms. About half of these are
for OMAP and submitted before but did not make it into v3.6-rc2.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tupl
-----END PGP SIGNATURE-----
Merge tag 'fixes-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc fixes from Arnd Bergmann:
"Bug fixes for various ARM platforms. About half of these are for OMAP
and submitted before but did not make it into v3.6-rc2."
* tag 'fixes-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: ux500: don't select LEDS_GPIO for snowball
ARM: imx: build i.MX6 functions only when needed
ARM: imx: select CPU_FREQ_TABLE when needed
ARM: imx: fix ksz9021rn_phy_fixup
ARM: imx: build pm-imx5 code only when PM is enabled
ARM: omap: allow building omap44xx without SMP
ARM: dts: imx51-babbage: fix esdhc cd/wp properties
ARM: imx6: spin the cpu until hardware takes it down
ARM: ux500: Ensure probing of Audio devices when Device Tree is enabled
ARM: ux500: Fix merge error, no matching driver name for 'snd_soc_u8500'
ARM i.MX6q: Add virtual 1/3.5 dividers in the LDB clock path
ARM: Kirkwood: fix Makefile.boot
ARM: Kirkwood: Fix iconnect leds
ARM: Orion: Set eth packet size csum offload limit
ARM: mv78xx0: fix win_cfg_base prototype
ARM: OMAP: dmtimers: Fix locking issue in omap_dm_timer_request*()
ARM: mmp: fix potential NULL dereference
ARM: OMAP4: Register the OPP table only for 4430 device
cpufreq: OMAP: Handle missing frequency table on SMP systems
ARM: OMAP4: sleep: Save the complete used register stack frame
...
This converts the ARM RealView machine over to using the common
clock. The approach is similar to the one used for the Integrator,
and we're reusing the ICST wrapper code.
We have to put the clock intialization in the timer init function
for the clocks to be available when initializing the timer,
keeping them in early_init() is too early for the common clk.
Since we now have to go down and compile drivers/clk/versatile
a CONFIG_COMMON_CLK_VERSATILE symbol has been added so the proper
code gets compiled into the kernel for either machine. A leftover
CLK_VERSATILE in the Integrator Kconfig was fixed up to use
the new symbol as well.
Tested on ARM RealView PB1176.
Cc: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Commit 02c981c07b only implements a little part of primaII clk tree
due to common clk framework was not ready at that time.
This patch converts the old driver to common clk and finish the full clk
tree.
Signed-off-by: Binghua Duan <Binghua.Duan@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The i.MX cpufreq implementation uses the CPU_FREQ_TABLE helpers,
so it needs to select that code to be built. This problem has
apparently existed since the i.MX cpufreq code was first merged
in v2.6.37.
Building IMX without CPU_FREQ_TABLE results in:
arch/arm/plat-mxc/built-in.o: In function `mxc_cpufreq_exit':
arch/arm/plat-mxc/cpufreq.c:173: undefined reference to `cpufreq_frequency_table_put_attr'
arch/arm/plat-mxc/built-in.o: In function `mxc_set_target':
arch/arm/plat-mxc/cpufreq.c:84: undefined reference to `cpufreq_frequency_table_target'
arch/arm/plat-mxc/built-in.o: In function `mxc_verify_speed':
arch/arm/plat-mxc/cpufreq.c:65: undefined reference to `cpufreq_frequency_table_verify'
arch/arm/plat-mxc/built-in.o: In function `mxc_cpufreq_init':
arch/arm/plat-mxc/cpufreq.c:154: undefined reference to `cpufreq_frequency_table_cpuinfo'
arch/arm/plat-mxc/cpufreq.c:162: undefined reference to `cpufreq_frequency_table_get_attr'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Yong Shen <yong.shen@linaro.org>
Cc: stable@vger.kernel.org
The PMU reservation mechanism was originally intended to allow OProfile
and perf-events to co-ordinate over access to the CPU PMU. Since then,
OProfile for ARM has moved to using perf as its backend, so the
reservation code is no longer used.
This patch removes the reservation code for the CPU PMU on ARM.
Signed-off-by: Will Deacon <will.deacon@arm.com>
From Linus Walleij <linus.walleij@linaro.org>
This patch set does a number of cleanups and a minor improvement
to U300, paving the way for single zImage and device tree:
- Deprecate ancient platforms to make the following patches easier to
make...
- Move out one header to platform data and one to the mach-u300 proper
to depopulate <mach/*>
- Consolidate core machine files
- Convert to sparse IRQs
* 'u300-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: u300: convert to sparse IRQs
ARM: u300: move DMA channel header into mach-u300
ARM: u300: delete remnant clkdev.h file
ARM: u300: merge u300.c into core.c and rid headers
pinctrl/coh901: move header to platform data dir
pinctrl/coh901: retire ancient GPIO block versions
ARM: u300: retire ancient platforms
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Seems that Thomas' and my patches collided during the last merge
window.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From Rob Herring <robherring2@gmail.com>:
This is the 2nd part of mach/io.h removals. This series removes io.h on
platforms with PCI by creating a fixed virtual I/O mapping and a common
__io() macro.
This version has changed a bit to accommodate Tegra converting its PCIe
host to a platform driver. Now the virtual space is only reserved during
early boot before .map_io() is called. The mapping is not created until
calling pci_ioremap_io which can be done at any point after vmalloc is
initialized.
I've gone back to fixed 64K windows for each PCI bus. This allows
removing all the i/o resource setup from the individually platforms and
placing it within the common ARM PCI code.
I've only tested versatilepb under qemu (with the model hacked up to
actually enable i/o space), so any testing is appreciated. iop3xx and
mv78xx0 have some risk of breaking as the PCI bus addresses are moved
to 0 from matching the cpu host bus addesss.
* cleanup/io-pci:
ARM: iop3xx: use fixed PCI i/o mapping
ARM: mv78xx0: use fixed pci i/o mapping
ARM: iop13xx: use fixed PCI i/o mapping
iop13xx: use more regular PCI I/O space handling
ARM: orion5x: use fixed PCI i/o mapping
ARM: kirkwood: use fixed PCI i/o mapping
ARM: dove: use fixed PCI i/o mapping
ARM: footbridge: use fixed PCI i/o mapping
ARM: shark: use fixed PCI i/o mapping
ARM: integrator: remove trailing whitespace on pci_v3.c
ARM: integrator: use fixed PCI i/o mapping
ARM: tegra: use fixed PCI i/o mapping
ARM: versatile: use fixed PCI i/o mapping
ARM: move PCI i/o resource setup into common code
ARM: Add fixed PCI i/o mapping
i2c: iop3xx: use standard gpiolib functions
i2c: iop3xx: clean-up trailing whitespace
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Bryan Wu <bryan.wu@canonical.com>:
Based on Linus Walleij's ARM LED consolidation work, this patchset introduce a
new generic led trigger for CPU not only for ARM but also for others.
For enabling CPU idle event, CPU arch code should call ledtrig_cpu() stub to
trigger idle start or idle end event.
These patches convert old style LED driver in arch/arm to gpio_led or new led
driver interface. Against 3.5 release and build successfully for all the machines.
Test ledtrig-cpu driver on OMAP4 Panda board.
v9 --> v10
* fix compiling issue on versatile_defconfig reported by Russell King
* rebase to 3.5 kernel and move patches to new git tree
v8 --> v9:
* use mutex to replace rw_sema pointed out by Tim Gardner
* add a new struct led_trigger_cpu
* add lock_is_inited to record mutex lock initialization
v6 --> v7:
* add a patch to unify the led-trigger name
* fix some typo pointed
* use BUG_ON to detect CPU numbers during building stage
v5 --> v6:
* replace __get_cpu_var() to per_cpu()
* remove smp_processor_id() which is wrong with for_each_possible_cpu()
* test on real OMAP4 Panda board
* add comments about CPU hotplug in the CPU LED trigger driver
v4 --> v5:
* rebase all the patches on top of latest linux-next
* replace on_each_cpu() with for_each_possible_cpu()
* add some description of ledtrig_cpu() API
* remove old leds code from driver nwflash.c, which should use a new led trigger then
* this trigger driver can be built as module now
v3 --> v4:
* fix a typo pointed by Jochen Friedrich
* fix some building errors
* add Reviewed-by and Tested-by into patch log
v2 --> v3:
* almost rewrote the whole ledtrig-cpu driver, which is more simple
* every CPU will have a per-CPU trigger
* cpu trigger can be assigned to any leds
* fix a lockdep issue in led-trigger common code
* other fix according to review
v1 --> v2:
* remove select operations in Kconfig of every machines
* add back supporting of led in core module of mach-integrator
* solidate name scheme in ledtrig-cpu.c
* add comments of CPU_LED_* cpu led events
* fold patches of RealView and Versatile together
* add machine_is_ check during assabet led driver init
* add some Acked-by in patch logs
* remove code for simpad machine in machine-sa11000, since Jochen Friedrich
introduced gpiolib and gpio-led driver for simpad
* on Assabet and Netwinder machine, LED operations is reversed like:
setting bit means turn off leds
clearing bit means turn on leds
* add a new function to read CM_CTRL register for led driver
* 'for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
ARM: use new LEDS CPU trigger stub to replace old one
ARM: mach-sa1100: retire custom LED code
ARM: mach-omap1: retire custom LED code
ARM: mach-pnx4008: remove including old leds event API header file
ARM: plat-samsung: remove including old leds event API header file
ARM: mach-pxa: retire custom LED code
char: nwflash: remove old led event code
ARM: mach-footbridge: retire custom LED code
ARM: mach-ebsa110: retire custom LED code
ARM: mach-clps711x: retire custom LED code of P720T machine
ARM: mach-integrator: retire custom LED code
ARM: mach-integrator: move CM_CTRL to header file for accessing by other functions
ARM: mach-orion5x: convert custom LED code to gpio_led and LED CPU trigger
ARM: mach-shark: retire custom LED code
ARM: mach-ks8695: remove leds driver, since nobody use it
ARM: mach-realview and mach-versatile: retire custom LED code
ARM: at91: convert old leds drivers to gpio_led and led_trigger drivers
led-triggers: create a trigger for CPU activity
Conflicts:
arch/arm/mach-clps711x/p720t.c
arch/arm/mach-sa1100/leds-cerf.c
arch/arm/mach-sa1100/leds-lart.c
Let's hope this is the last time we pull this and it doesn't cause
more trouble. I have verified that version 10 causes no build
warnings or errors any more, and the patches still look good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This converts the U300 to use sparse IRQs, which is simple now
that the number of machines are reduced.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that ARM has implemented its spinlocks with tickets we don't
need to use the generic lockbreak algorithm. Remove the Kconfig
from ARM so that we use the arch_spin_is_contended() definition
from the asm header. This also saves a word in each lock because
we don't need the break_lock member anymore.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Changes in v5:
- make XEN_DOM0 depend on XEN;
- avoid "select XEN_DOM0" in XEN.
Changes in v2:
- mark Xen guest support on ARM as EXPERIMENTAL.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
CC: Sergei Shtylyov <sshtylyov@mvista.com>
This branch contains a set of device-tree conversions for Marvell Orion
platforms that were staged early but took a few tries to get the branch
into a format where it was suitable for us to pick up.
Given that most people working on these platforms are hobbyists with
limited time, we were a bit more flexible with merging it even though
it came in late.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xb8w
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc Marvell Orion device-tree updates from Olof Johansson:
"This contains a set of device-tree conversions for Marvell Orion
platforms that were staged early but took a few tries to get the
branch into a format where it was suitable for us to pick up.
Given that most people working on these platforms are hobbyists with
limited time, we were a bit more flexible with merging it even though
it came in late."
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: Kirkwood: Replace mrvl with marvell
ARM: Kirkwood: Describe GoFlex Net LEDs and SATA in DT.
ARM: Kirkwood: Describe Dreamplug LEDs in DT.
ARM: Kirkwood: Describe iConnects LEDs in DT.
ARM: Kirkwood: Describe iConnects temperature sensor in DT.
ARM: Kirkwood: Describe IB62x0 LEDs in DT.
ARM: Kirkwood: Describe IB62x0 gpio-keys in DT.
ARM: Kirkwood: Describe DNS32? gpio-keys in DT.
ARM: Kirkwood: Move common portions into a kirkwood-dnskw.dtsi
ARM: Kirkwood: Replace DNS-320/DNS-325 leds with dt bindings
ARM: Kirkwood: Describe DNS325 temperature sensor in DT.
ARM: Kirkwood: Use DT to configure SATA device.
ARM: kirkwood: use devicetree for SPI on dreamplug
ARM: kirkwood: Add LS-XHL and LS-CHLv2 support
ARM: Kirkwood: Initial DTS support for Kirkwood GoFlex Net
ARM: Kirkwood: Add basic device tree support for QNAP TS219.
ATA: sata_mv: Add device tree support
ARM: Orion: DTify the watchdog timer.
ARM: Orion: Add arch support needed for I2C via DT.
ARM: kirkwood: use devicetree for orion-spi
...
Conflicts:
drivers/watchdog/orion_wdt.c
Merge Andrew's first set of patches:
"Non-MM patches:
- lots of misc bits
- tree-wide have_clk() cleanups
- quite a lot of printk tweaks. I draw your attention to "printk:
convert the format for KERN_<LEVEL> to a 2 byte pattern" which
looks a bit scary. But afaict it's solid.
- backlight updates
- lib/ feature work (notably the addition and use of memweight())
- checkpatch updates
- rtc updates
- nilfs updates
- fatfs updates (partial, still waiting for acks)
- kdump, proc, fork, IPC, sysctl, taskstats, pps, etc
- new fault-injection feature work"
* Merge emailed patches from Andrew Morton <akpm@linux-foundation.org>: (128 commits)
drivers/misc/lkdtm.c: fix missing allocation failure check
lib/scatterlist: do not re-write gfp_flags in __sg_alloc_table()
fault-injection: add tool to run command with failslab or fail_page_alloc
fault-injection: add selftests for cpu and memory hotplug
powerpc: pSeries reconfig notifier error injection module
memory: memory notifier error injection module
PM: PM notifier error injection module
cpu: rewrite cpu-notifier-error-inject module
fault-injection: notifier error injection
c/r: fcntl: add F_GETOWNER_UIDS option
resource: make sure requested range is included in the root range
include/linux/aio.h: cpp->C conversions
fs: cachefiles: add support for large files in filesystem caching
pps: return PTR_ERR on error in device_create
taskstats: check nla_reserve() return
sysctl: suppress kmemleak messages
ipc: use Kconfig options for __ARCH_WANT_[COMPAT_]IPC_PARSE_VERSION
ipc: compat: use signed size_t types for msgsnd and msgrcv
ipc: allow compat IPC version field parsing if !ARCH_WANT_OLD_COMPAT_IPC
ipc: add COMPAT_SHMLBA support
...
Rather than #define the options manually in the architecture code, add
Kconfig options for them and select them there instead. This also allows
us to select the compat IPC version parsing automatically for platforms
using the old compat IPC interface.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE and use this instead
of the multitude of #if defined() checks in atomic64_test.c
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull PWM subsystem from Thierry Reding:
"The new PWM subsystem aims at collecting all implementations of the
legacy PWM API and to eventually replace it completely.
The subsystem has been in development for over half a year now and
many drivers have already been converted. It has been in linux-next
for a couple of weeks and there have been no major issues so I think
it is ready for inclusion in your tree."
Arnd Bergmann <arnd@arndb.de>:
"Very much Ack on the new subsystem. It uses the interface
declarations as the previously separate pwm drivers, so nothing
changes for now in the drivers using it, although it enables us to
change those more easily in the future if we want to.
This work is also one of the missing pieces that are required to
eventually build ARM kernels for multiple platforms, which is
currently prohibited (amongs other things) by the fact that you cannot
have more than one driver exporting the pwm functions."
Tested-and-acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Philip, Avinash <avinashphilip@ti.com> # TI's AM33xx platforms
Acked-By: Alexandre Pereira da Silva <aletes.xgr@gmail.com> # LPC32XX
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sachin Kamat <sachin.kamat@linaro.org>
Fix up trivial conflicts with other cleanups and DT updates.
* 'for-3.6' of git://gitorious.org/linux-pwm/linux-pwm: (36 commits)
pwm: pwm-tiehrpwm: PWM driver support for EHRPWM
pwm: pwm-tiecap: PWM driver support for ECAP APWM
pwm: fix used-uninitialized warning in pwm_get()
pwm: add lpc32xx PWM support
pwm_backlight: pass correct brightness to callback
pwm: Use pr_* functions in pwm-samsung.c file
pwm: Convert pwm-samsung to use devm_* APIs
pwm: Convert pwm-tegra to use devm_clk_get()
pwm: pwm-mxs: Return proper error if pwmchip_remove() fails
pwm: pwm-bfin: Return proper error if pwmchip_remove() fails
pwm: pxa: Propagate pwmchip_remove() error
pwm: Convert pwm-pxa to use devm_* APIs
pwm: Convert pwm-vt8500 to use devm_* APIs
pwm: Convert pwm-imx to use devm_* APIs
pwm: Conflict with legacy PWM API
pwm: pwm-mxs: add pinctrl support
pwm: pwm-mxs: use devm_* managed functions
pwm: pwm-mxs: use global reset function stmp_reset_block
pwm: pwm-mxs: encode soc name in compatible string
pwm: Take over maintainership of the PWM subsystem
...
Pull ARM updates from Russell King:
"First ARM push of this merge window, post me coming back from holiday.
This is what has been in linux-next for the last few weeks. Not much
to say which isn't described by the commit summaries."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (32 commits)
ARM: 7463/1: topology: Update cpu_power according to DT information
ARM: 7462/1: topology: factorize the update of sibling masks
ARM: 7461/1: topology: Add arch_scale_freq_power function
ARM: 7456/1: ptrace: provide separate functions for tracing syscall {entry,exit}
ARM: 7455/1: audit: move syscall auditing until after ptrace SIGTRAP handling
ARM: 7454/1: entry: don't bother with syscall tracing on ret_from_fork path
ARM: 7453/1: audit: only allow syscall auditing for pure EABI userspace
ARM: 7452/1: delay: allow timer-based delay implementation to be selected
ARM: 7451/1: arch timer: implement read_current_timer and get_cycles
ARM: 7450/1: dcache: select DCACHE_WORD_ACCESS for little-endian ARMv6+ CPUs
ARM: 7449/1: use generic strnlen_user and strncpy_from_user functions
ARM: 7448/1: perf: remove arm_perf_pmu_ids global enumeration
ARM: 7447/1: rwlocks: remove unused branch labels from trylock routines
ARM: 7446/1: spinlock: use ticket algorithm for ARMv6+ locking implementation
ARM: 7445/1: mm: update CONTEXTIDR register to contain PID of current process
ARM: 7444/1: kernel: add arch-timer C3STOP feature
ARM: 7460/1: remove asm/locks.h
ARM: 7439/1: head.S: simplify initial page table mapping
ARM: 7437/1: zImage: Allow DTB command line concatenation with ATAG_CMDLINE
ARM: 7436/1: Do not map the vectors page as write-through on UP systems
...
Both IRQ and GPIO controllers can now be represented in DT. The IRQ
controllers are setup first, and then the GPIO controllers. Interrupts
for GPIO lines are placed directly after the main interrupts in the
interrupt space.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Josh Coombs <josh.coombs@gmail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Move iop33x and iop32x PCI to fixed i/o mapping and remove io.h. This
changes the PCI bus addresses from the cpu address to 0 based. It appears
that there is translation h/w for this, but its untested.
Not sure what to do with io_offset. I think it should always be 0.
AFAICT, PCI setup is skipped if the ATU is already setup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move mv78xx0 PCI to fixed i/o mapping and remove io.h. This changes the PCI
bus addresses from the cpu address to 0 based. It appears that there is
translation h/w for this, but its untested.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move iop13xx PCI to fixed i/o mapping and remove io.h.
This changes the PCIe bus address to start at 0x10000. Let's hope this
works. If it does not, the alternative would be to revert the value we
write into OIOTVR to zero and set sys->io_offset to 64K.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move orion5x PCI to fixed i/o mapping and remove io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move kirkwood PCI to fixed i/o mapping and remove io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
The i/o regions are changed from 1MB to 64KB. It's likely that the 2nd
bus is not setup correctly.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move footbridge PCI to fixed i/o mapping. io.h is still needed for the
!MMU case.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Convert shark to use the fixed i/o mapping and remove io.h.
This shrinks the mapping from 256MB to 1MB, but nothing is using that much
space AFAICT.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move tegra PCI to fixed i/o mapping and remove io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Colin Cross <ccross@android.com>
Cc: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Due to automatic merge of a613163dff
"ARM: integrator: convert to common clock" and
56a34b03ff "ARM: versatile: Make
plat-versatile clock optional" two platforms: Integrator and
Versatile Express now select both COMMON_CLK and
PLAT_VERSATILE_CLOCK which breaks building them. Fixed now.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
framework improvments, platform ports and new DT bindings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=V8ad
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull common clk framework changes from Michael Turquette:
"This includes a small number of core framework improvments, platform
ports and new DT bindings."
Fix up trivial conflicts in drivers/clk/Makefile
* tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux: (21 commits)
clk: fix compile for OF && !COMMON_CLK
clk: fix clk_get on of_clk_get_by_name return check
clk: mxs: clk_register_clkdev mx28 usb clocks
clk: add highbank clock support
dt: add clock binding doc to primecell bindings
clk: add DT fixed-clock binding support
clk: add DT clock binding support
ARM: integrator: convert to common clock
clk: add versatile ICST307 driver
ARM: integrator: put symbolic bus names on devices
ARM: u300: convert to common clock
clk: cache parent clocks only for muxes
clk: wm831x: Add initial WM831x clock driver
clk: Constify struct clk_init_data
clk: Add CLK_IS_BASIC flag to identify basic clocks
clk: Add support for rate table based dividers
clk: Add support for power of two type dividers
clk: mxs: imx28: decrease the frequency of ref_io1 for SSP2 and SSP3
clk: mxs: add clkdev lookup for pwm
clk: mxs: Fix the GPMI clock name
...
We are converting platforms to use the pinctrl framework over time,
rather than using platform specific code for the same effect. This
adds the respective driver for the prima2 platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YodD
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc pincontrol drivers update from Arnd Bergmann:
"We are converting platforms to use the pinctrl framework over time,
rather than using platform specific code for the same effect. This
adds the respective driver for the prima2 platform."
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: prima2: enable gpiolib unconditionally
PINCTRL: SiRF: add GPIO and GPIO irq support in CSR SiRFprimaII
The I.MX platform is getting converted to use sparse IRQs. We are doing
this for all platforms over time, because this is one of the
requirements for building a multiplatform kernel, and generally a good
idea.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Y2Sm
-----END PGP SIGNATURE-----
Merge tag 'irq' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc sparse IRQ conversion from Arnd Bergmann:
"The I.MX platform is getting converted to use sparse IRQs. We are
doing this for all platforms over time, because this is one of the
requirements for building a multiplatform kernel, and generally a good
idea."
* tag 'irq' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx: select USE_OF
ARM: imx: Fix build error due to missing irqs.h include
ARM: imx: enable SPARSE_IRQ for imx platform
ARM: fiq: change FIQ_START to a variable
tty: serial: imx: remove the use of MXC_INTERNAL_IRQS
ARM: imx: remove unneeded mach/irq.h inclusion
i2c: imx: remove unneeded mach/irqs.h inclusion
ARM: imx: add a legacy irqdomain for mx31ads
ARM: imx: add a legacy irqdomain for 3ds_debugboard
ARM: imx: pass gpio than irq number into mxc_expio_init
ARM: imx: leave irq_base of wm8350_platform_data uninitialized
dma: ipu: remove the use of ipu_platform_data
ARM: imx: move irq_domain_add_legacy call into avic driver
ARM: imx: move irq_domain_add_legacy call into tzic driver
gpio/mxc: move irq_domain_add_legacy call into gpio driver
ARM: imx: eliminate macro IRQ_GPIOx()
ARM: imx: eliminate macro IOMUX_TO_IRQ()
ARM: imx: eliminate macro IMX_GPIO_TO_IRQ()
These changes are all for individual board files. In the long run, those
files will largely go away, and the amount of changes appears to be
continuously decreasing, which is a good sign. This time around, changes
are focused on tegra, omap and samsung.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nKn1
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc board specific updates from Arnd Bergmann:
"These changes are all for individual board files. In the long run,
those files will largely go away, and the amount of changes appears to
be continuously decreasing, which is a good sign. This time around,
changes are focused on tegra, omap and samsung."
Fix conflicts in arch/arm/mach-{omap2/common-board-devices.c,tegra/Makefile.boot}
as per the 'for-linus' branch.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: EXYNOS: Add leds status1 and status2 on Origen board
ARM: S3C64XX: Mark most Cragganmore initdata devinitdata
ARM: EXYNOS: Add missing .reserve field to SMDKC210
ARM: EXYNOS: Add DRM device to SMDK4X12 board
ARM: S3C64XX: Clean up after SPI driver platform data updates
ARM: SAMSUNG: no need to set the value for clk_xusbxti when it is 24Mhz
ARM: EXYNOS: Add framebuffer support for SMDK4X12
ARM: EXYNOS: Add HSOTG support to SMDK4X12
ARM: S5PV210: Add audio platform device in Goni board
ARM: S5PV210: Add audio platform device in Aquila board
ARM: EXYNOS: Add audio platform device in SMDKV310 board
ARM: S3C64XX: Don't specify an irq_base for WM1192-EV1 board
ARM: OMAP3: Fix omap3evm randconfig error introduced by VBUS support
ARM: OMAP: board-omap4panda: MUX configuration for sys_nirq2
ARM: OMAP: board-4430sdp: MUX configuration for sys_nirq2
ARM: OMAP3530evm: set pendown_state and debounce time for ads7846
ARM: omap3evm: enable VBUS switch for EHCI tranceiver
ARM: OMAP3EVM: Adding USB internal LDOs board file
ARM: OMAP3EVM: Add NAND flash definition
ARM: OMAP3: cm-t35: add tvp5150 decoder support
...
This adds support for three new SoC types:
* The mvebu platform includes Marvell's Armada XP and Armada 370 chips,
made by the mvebu business unit inside of Marvell. Since the same
group also made the older but similar platforms we call "orion5x",
"kirkwood", "mv78xx0" and "dove", we plan to move all of them into
the mach-mvebu directory in the future.
* socfpga is Altera's platform based on Cortex-A9 cores and a lot of
FPGA space. This is similar to the Xilinx zynq platform we already
support. The code is particularly clean, which is helped by the fact
that the hardware doesn't do much besides the parts that are
expected to get added in the FPGA.
* The OMAP subarchitecture gains support for the latest generation,
the OMAP5 based on the new Cortex-A15 core. Support is rather
rudimentary for now, but will be extended in the future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIVAwUAUA2deGCrR//JCVInAQJLxg/8DHL6usaciRX0rDzxAkv2h0cezjgR/ect
OfHdxhge7R50NEbf4Jayyly8fIvADJB5nIgk1jhYzAOroVAGxiZQxhyGn3p+Cpbm
4weu78Uk5habgGA3DmV/R8rKhd1iFtr1DSHbogU43UjPj9Zz5WOREGNJehvxOr/2
hUfymdqxNg4ivCWyA3w4IKhxA/Hrs351n3J3sY3wjLRPn/uZIlvyx4Q8InteAJZp
96u5F9y34CxB9SkXAX0P+Bdb0L1fWhZ1J6E8wjOMp/t3LaSXvvWVgCl6MxTcERpf
jeeABKPTQx99zkH3MdPRQfgBMwsez4L4dXh3qcJaEoqF//UXpE9cTTdjqYu6NRsJ
znO8Ns8a2X4zX6KF4ySQf2jtLzH4aF21nq6NTJyYyfDWZixqRSKawbSsYqc1vtmi
ReQ00feJrO60/A4Ks25asUfubqm/SXZ6BfHSgS/ZaOjgJaW9X42CUKnuIywXPTrY
cAGDh4v1ZrWdXiQIu7oKgESSQNi4GrAEDYqVYs/PmSk2UiuzHcSuPMYxsCmLk8mH
By7CLByXGOjzD9678LX2VHvKhK2l7Wd+Vkp/pGk4N4fK581JBfyBWfE0T5rpOU28
+fIFVAV6U0I1OW879b5LmC/kjtmHPxePP6XUcHE152ef1CiT6zm5IE+C2Ukso71V
+WKxBRBOxII=
=MwdJ
-----END PGP SIGNATURE-----
Merge tag 'newsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull support for three new arm SoC types from Arnd Bergmann:
- The mvebu platform includes Marvell's Armada XP and Armada 370 chips,
made by the mvebu business unit inside of Marvell. Since the same
group also made the older but similar platforms we call "orion5x",
"kirkwood", "mv78xx0" and "dove", we plan to move all of them into
the mach-mvebu directory in the future.
- socfpga is Altera's platform based on Cortex-A9 cores and a lot of
FPGA space. This is similar to the Xilinx zynq platform we already
support. The code is particularly clean, which is helped by the fact
that the hardware doesn't do much besides the parts that are expected
to get added in the FPGA.
- The OMAP subarchitecture gains support for the latest generation, the
OMAP5 based on the new Cortex-A15 core. Support is rather
rudimentary for now, but will be extended in the future.
* tag 'newsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
ARM: socfpga: initial support for Altera's SOCFPGA platform
arm: mvebu: generate DTBs for supported SoCs
ARM: mvebu: MPIC: read number of interrupts from control register
arm: mach-mvebu: add entry to MAINTAINERS
arm: mach-mvebu: add compilation/configuration change
arm: mach-mvebu: add defconfig
arm: mach-mvebu: add documentation for new device tree bindings
arm: mach-mvebu: add support for Armada 370 and Armada XP with DT
arm: mach-mvebu: add source files
arm: mach-mvebu: add header
clocksource: time-armada-370-xp: Marvell Armada 370/XP SoC timer driver
ARM: Kconfig update to support additional GPIOs in OMAP5
ARM: OMAP5: Add the build support
arm/dts: OMAP5: Add omap5 dts files
ARM: OMAP5: board-generic: Add device tree support
ARM: omap2+: board-generic: clean up the irq data from board file
ARM: OMAP5: Add SMP support
ARM: OMAP5: Add the WakeupGen IP updates
ARM: OMAP5: l3: Add l3 error handler support for omap5
ARM: OMAP5: gpmc: Update gpmc_init()
...
Conflicts:
Documentation/devicetree/bindings/arm/omap/omap.txt
arch/arm/mach-omap2/Makefile
drivers/clocksource/Kconfig
drivers/clocksource/Makefile
This contains two branches dealing with timers, one for the picoxcell
platform that is now using DT with the platform-independent
dw_apb_timer driver. The other change is for the omap-specific
dmtimer driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2bZ2
-----END PGP SIGNATURE-----
Merge tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc timer updates from Arnd Bergmann:
"This contains two branches dealing with timers, one for the picoxcell
platform that is now using DT with the platform-independent
dw_apb_timer driver. The other change is for the omap-specific
dmtimer driver."
* tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
clocksource: dw_apb_timer: Add common DTS glue for dw_apb_timer
ARM: OMAP2+: Simplify dmtimer clock aliases
ARM: OMAP2+: Move dmtimer clock set function to dmtimer driver
ARM: OMAP1: Fix dmtimer support
ARM: OMAP: Add flag to indicate if a timer needs a manual reset
ARM: OMAP: Remove timer function pointer for context loss counter
ARM: OMAP: Remove loses_context variable from timer platform data
ARM: OMAP2+: Fix external clock support for dmtimers
ARM: OMAP2+: HWMOD: Correct timer device attributes
ARM: OMAP: Add DMTIMER capability variable to represent timer features
ARM: OMAP2+: Add dmtimer platform function to reserve systimers
ARM: OMAP2+: Remove unused max number of timers definition
ARM: OMAP: Remove unnecessary clk structure
This is stuff that does not fit well into another category and in
particular is not related to a particular board. The largest part
in here is extending the am33xx support in the omap platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Qclg
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific updates from Arnd Bergmann:
"This is stuff that does not fit well into another category and in
particular is not related to a particular board. The largest part in
here is extending the am33xx support in the omap platform."
Fix up trivial conflicts in arch/arm/mach-{imx/mach-mx35_3ds.c, tegra/Makefile}
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (74 commits)
ARM: LPC32xx: Add PWM support
ARM: LPC32xx: Add PWM clock
ARM: LPC32xx: Set system serial based on cpu unique id
ARM: vexpress: Config option for early printk console
ARM: vexpress: Add Device Tree for V2P-CA15_CA7 core tile
ARM: vexpress: Convert V2P-CA15 Device Tree to 64 bit addresses
ARM: vexpress: Add fixed regulator for SMSC
ARM: vexpress: Add missing SP804 interrupt in motherboard's DTS files
ARM: vexpress: Initial common clock support
ARM: SAMSUNG: Introduce Kconfig variable for Samsung custom clk API
ARM: EXYNOS: Add missing static storage class specifier in pmu.c file
ARM: EXYNOS: Make combiner_init function static
ARM: EXYNOS: Update HSOTG PHY clock setting for EXYNOS4X12
ARM: versatile: Make plat-versatile clock optional
ARM: vexpress: Check master site in daughterboard's sysctl operations
ARM: vexpress: remove automatic errata workaround selection
ARM: LPC32xx: Adjust to pl08x DMA interface changes
ARM: EXYNOS: Clear SYS_WDTRESET bit to use watchdog reset
ARM: imx: fix mx51 ehci setup errors
ARM: imx: make ehci power/oc polarities configurable
...
From Roland Stigge <stigge@antcom.de>:
this LPC32xx core update (branch lpc32xx/core2) builds upon the
previously provided lpc32xx/core-fixes. Basically including PWM support
(for the PWM driver from Alexandre already in the pwm tree), and
CPU ID.
* 'lpc32xx/core2' of git://git.antcom.de/linux-2.6:
ARM: LPC32xx: Add PWM support
ARM: LPC32xx: Add PWM clock
ARM: LPC32xx: Set system serial based on cpu unique id
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
SMSC driver requires "vdd33a" and "vddvario" regulator supplies now.
Add fixed regulator describing 3V3 power line (in both motherboard's
Device Trees and the non-DT code) and force fixed regulator config
option if regulators framework is enabled.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
This patch makes Versatile Express use the common clock framework
instead of the plat-versatile implementation.
It defines clock provider for VE's OSCs (clock generators) and
registers all required fixed and variable clock sources (for both
motherboard and core tile).
This is a simple conversion of the existing state and will be
extended (and migrated to drivers/clk) in the near future.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Make a common device tree glue for clocksource/dw_apb_timer.
Move mach-picoxcell/time.c to be a generic device tree application
of the dw_apb_timer.
Configure mach-picoxcell to use the dw_apb_timer_of device tree
implementation in drivers/clocksource.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
... in preparation for common clock coming for Integrator
and Versatile Express.
Based on Linus Walleij's "ARM: integrator: convert to common
clock" patch.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
This adds real clock support to Calxeda Highbank SOC using the common
clock infrastructure.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
[mturquette@linaro.org: fixed up invalid writes to const struct member]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This converts the Integrator platform to use common clock
and the ICST driver. Since from this point not all ARM
reference platforms use the clock, we define
CONFIG_PLAT_VERSATILE_CLOCK and select it for all platforms
except the Integrator.
Open issue: I could not use the .init_early() field of the
machine descriptor to initialize the clocks, but had to
move them to .init_irq(), so presumably .init_early() is
so early that common clock is not up, and .init_machine()
is too late since it's needed for the clockevent/clocksource
initialization. Any suggestions on how to solve this is
very welcome.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[mturquette@linaro.org: use 'select' instead of versatile Kconfig]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This converts the U300 clock implementation over to use the common
struct clk and moves the implementation down into drivers/clk.
Since VCO isn't used in tree it was removed, it's not hard to
put it back in if need be.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[mturquette@linaro.org: trivial Makefile conflict]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
From Tony Lindgren <tony@atomide.com>:
This branch contains minimal support for omap5 to boot to a
console without clock framework support. This branch depends
on omap-cleanup-part2-for-v3.6.
* 'devel-omap5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: Kconfig update to support additional GPIOs in OMAP5
ARM: OMAP5: Add the build support
arm/dts: OMAP5: Add omap5 dts files
ARM: OMAP5: board-generic: Add device tree support
ARM: omap2+: board-generic: clean up the irq data from board file
ARM: OMAP5: Add SMP support
ARM: OMAP5: Add the WakeupGen IP updates
ARM: OMAP5: l3: Add l3 error handler support for omap5
ARM: OMAP5: gpmc: Update gpmc_init()
ARM: OMAP5: timer: Add clocksource, clockevent support
ARM: OMAP5: Add minimal support for OMAP5430 SOC
ARM: OMAP5: id: Add cpu id for ES versions
ARM: OMAP: counter-32k: Select the CR register offset using the IP scheme
ARM: OMAP2+: Move stubbed secure_sram_reserve function to a common.c and call it __weak
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
DCACHE_WORD_ACCESS uses the word-at-a-time API for optimised string
comparisons in the vfs layer.
This patch implements support for load_unaligned_zeropad for ARM CPUs
with native support for unaligned memory accesses (v6+) when running
little-endian.
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch implements the word-at-a-time interface for ARM using the
same algorithm as x86. We use the fls macro from ARMv5 onwards, where
we have a clz instruction available which saves us a mov instruction
when targetting Thumb-2. For older CPUs, we use the magic 0x0ff0001
constant. Big-endian configurations make use of the implementation from
asm-generic.
With this implemented, we can replace our byte-at-a-time strnlen_user
and strncpy_from_user functions with the optimised generic versions.
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch allows the ATAG_CMDLINE provided by the bootloader to be
concatenated to the bootargs property of the device tree.
This is useful to merge static values defined in the device tree
with the boot loader's (possibly) more dynamic values, such as
startup reasons and more.
The bootloader should use the device tree to pass those values to
the kernel, but that's not always simple (old bootloader or very
small one).
The behaviour is the same as the one introduced by Victor Boivie in
4394c12442 by extending the CONFIG_CMDLINE.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
OMAP5 has 8 GPIO banks so that there are 32x8 = 256 GPIOs.
In order for the gpiolib to detect and initialize these
additional GPIOs and other TWL GPIOs, ARCH_NR_GPIO is set
to 512 instead of present 256.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Reported-by: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
From Stephen Warren <swarren@wwwdotorg.org>
This branch contains changes to Tegra board files, and related Kconfig and
Makefile changes. Highlights include:
* Removal of Seaboard/Springbank board files; these boards can now only be
used with device tree.
* Use of small parts of some non-DT board files from the DT board files. This
enables all features that the non-DT board files have, when booting from DT.
This will allow almost complete removal of all non-DT board files in v3.7.
* Other miscellaneous changes.
This branch is based on Tegra's for-3.6/cleanup branch from a previous pull
request.
* 'for-3.6/boards' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: use of_default_bus_match_table
ARM: tegra: add device tree AUXDATA for APBDMA
ARM: tegra: paz00: enable WiFi rfkill when booting from device tree
ARM: tegra: harmony: init regulators, PCIe when booting from DT
ARM: tegra: trimslice: enable PCIe when booting from device tree
ARM: tegra: remove Seaboard board files
ARM: tegra: remove CONFIG_MACH_TEGRA_DT
ARM: tegra: make .dts compilation depend on Tegra2 support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Two bug fixes for the previous state of the imx sparse irq changes.
* 'imx/sparse-irq' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: select USE_OF
ARM: imx: Fix build error due to missing irqs.h include
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit
544496a (ARM: imx: move irq_domain_add_legacy call into avic driver)
introduced unconditional calls to irq_find_mapping and
irq_domain_add_legacy, but it's still possible to have a .config without
CONFIG_IRQ_DOMAIN=y resulting in
CC arch/arm/plat-mxc/avic.o
arch/arm/plat-mxc/avic.c: In function 'avic_handle_irq':
arch/arm/plat-mxc/avic.c:172: error: implicit declaration of function 'irq_find_mapping'
arch/arm/plat-mxc/avic.c: In function 'mxc_init_irq':
arch/arm/plat-mxc/avic.c:207: error: implicit declaration of function 'irq_domain_add_legacy'
arch/arm/plat-mxc/avic.c:208: error: 'irq_domain_simple_ops' undeclared (first use in this function)
arch/arm/plat-mxc/avic.c:208: error: (Each undeclared identifier is reported only once
arch/arm/plat-mxc/avic.c:208: error: for each function it appears in.)
arch/arm/plat-mxc/avic.c:208: warning: assignment makes pointer from integer without a cast
make[3]: *** [arch/arm/plat-mxc/avic.o] Error 1
make[2]: *** [arch/arm/plat-mxc/avic.o] Error 2
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
While selecting CONFIG_IRQ_DOMAIN would be enough, USE_OF is the future
and implies CONFIG_IRQ_DOMAIN. So select USE_OF for ARCH_MXC and drop
other explicit selects that are superflous now.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The pinctrl code needs GPIOLIB to be enabled, so make
sure that it cannot be built otherwise. This fixes
the prima2_defconfig.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <21cnbao@gmail.com>
From Shawn Guo <shawn.guo@linaro.org>, this makes it possible to use
sparse irqs with mach-imx.
* 'imx/sparse-irq' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: enable SPARSE_IRQ for imx platform
ARM: fiq: change FIQ_START to a variable
tty: serial: imx: remove the use of MXC_INTERNAL_IRQS
ARM: imx: remove unneeded mach/irq.h inclusion
i2c: imx: remove unneeded mach/irqs.h inclusion
ARM: imx: add a legacy irqdomain for mx31ads
ARM: imx: add a legacy irqdomain for 3ds_debugboard
ARM: imx: pass gpio than irq number into mxc_expio_init
ARM: imx: leave irq_base of wm8350_platform_data uninitialized
dma: ipu: remove the use of ipu_platform_data
ARM: imx: move irq_domain_add_legacy call into avic driver
ARM: imx: move irq_domain_add_legacy call into tzic driver
gpio/mxc: move irq_domain_add_legacy call into gpio driver
ARM: imx: eliminate macro IRQ_GPIOx()
ARM: imx: eliminate macro IOMUX_TO_IRQ()
ARM: imx: eliminate macro IMX_GPIO_TO_IRQ()
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Move the driver to drivers/pwm/ and convert it to use the framework.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
In SiRFprimaII, Each GPIO pin can be configured as input or output
independently. If a GPIO is configured as input, it can also be
enabled as an interrupt source (either edge or level triggered).
These pins must be either MUXed as GPIO or other function pads.
Signed-off-by: Yuping Luo <yuping.luo@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
As all irqchips on imx have been changed to allocate their irq_descs,
and all unneeded mach/irqs.h inclusions on imx have been cleaned up,
now it's time to select SPARSE_IRQ for imx/mxc.
The SPARSE_IRQ support forces irqs allocation starting from 16. All
those static irq number definition for SoCs need to shift 16 to keep
non-DT boot works.
With all those static IRQ number and start definitions removed from
mach/irqs.h, the header becomes just a container of a couple of
mach-imx specific irq/fiq calls. Since mach/irqs.h is not included
by asm/irq.h now, the users of mxc_set_irq_fiq needs to explicitly
include mach/irqs.h themselves.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
The powerdomain and clockdomain data for the AM35xx are finally fixed.
The AM35xx EMAC/MDIO Ethernet controller integration code has been
converted to use the OMAP device and hwmod framework. Also the UART4
and HSOTGUSB warnings have been fixed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=2b0z
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-d-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes-non-critical
Some OMAP AM35xx fixes.
The powerdomain and clockdomain data for the AM35xx are finally fixed.
The AM35xx EMAC/MDIO Ethernet controller integration code has been
converted to use the OMAP device and hwmod framework. Also the UART4
and HSOTGUSB warnings have been fixed.
There is no way to build OMAP kernels without an MMU
at this point because of dependencies on MMU-only functions.
As long as nobody is interested in fixing this, let's just disable
this platforms for nommu kernels.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 4d5fc58dbe (ARM: remove bunch of
now unused mach/io.h files) removed the orion5x io.h. Unfortunately,
this is still needed for the definition of IO_SPACE_LIMIT which
overrides the default 64K. All Orion based systems have 1Mbyte of IO
space per PCI[e] bus, and try to request_resource() this size. Orion5x
has two such PCI buses.
It is likely that the original, removed version, was broken. This
version might be less broken. However, it has not been tested on
hardware with a PCI card, let alone hardware with a PCI card with IO
capabilities.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* Make ARCH_TEGRA select USE_OF; DT is the way forward.
* Build board-dt-tegra*.c when the relevant Tegra SoC support is enabled,
rather than requiring a specific config option for this.
* The board-specific config options already build board-*-pinmux.o, and
when booting from device tree these files are no longer needed, so we
can remove some Makefile commands related to those files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
A bit larger set than usual, unfortunately -- I've been sitting on them
longer than I meant to so it's really more like 2 -rc pull requests in
one, volume-wise.
Nearly everything is fixes for fallout from the merge window, or other
fixes for bugs. The one exception is the highbank L2-enablement patch,
but it was contained enough that I picked it up anyway:
- i.MX fixes, mostly for clock and pinctrl changes
- OMAP fixes, mostly PM-related
- A patch to enable L2 on highbank
- A couple of fixes for PXA, Kirkwood, Versatile
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=x9VX
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A bit larger set than usual, unfortunately -- I've been sitting on
them longer than I meant to so it's really more like 2 -rc pull
requests in one, volume-wise.
Nearly everything is fixes for fallout from the merge window, or other
fixes for bugs. The one exception is the highbank L2-enablement
patch, but it was contained enough that I picked it up anyway:
- i.MX fixes, mostly for clock and pinctrl changes
- OMAP fixes, mostly PM-related
- A patch to enable L2 on highbank
- A couple of fixes for PXA, Kirkwood, Versatile"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (30 commits)
ARM: Kirkwood: Fix clk problems modular ethernet driver
arm: versatile: fix and enable PCI I/O space
ARM: highbank: Add smc calls to enable/disable the L2
ARM i.MX imx21ads: Fix overlapping static i/o mappings
ARM: imx6: exit coherency when shutting down a cpu
ARM: mx51: Add pinctrl_provide_dummies()
ARM: mx31: Add pinctrl_provide_dummies()
ARM: OMAP2+: Fix compile for CONFIG_TIDSPBRIDGE platform init code
ARM: OMAP3: Fix omap3_l3_block_irq warning when CONFIG_BUG is not set
ARM: OMAP: Fix MMC_OMAP build when only MMC_OMAP_HS is selected
OMAP2+: UART: Add mechanism to probe uart pins and configure rx wakeup
ARM: mmp: fix missing cascade_irq in irq handler
ARM: dts: update memory size on brownstone
ARM i.MX27 Visstrim M10: fix gpio handling.
ARM i.MX53: Fix PLL4 base address
ARM i.MX pllv2: make round_rate accurate
ARM i.MX pllv2: use standard register set unconditionally
ARM: OMAP: Fix lis3lv02d accelerometer to use gpio_to_irq
ARM: imx: only call l2x0_init if it's available
ARM: imx: only specify i2c device type once
...
With commit 4d5fc58dbe (ARM: remove bunch of now unused
mach/io.h files), the I/O space setup was completely broken on
versatile. This patch fixes that and prepares for further
I/O space clean-up.
I/O space handling on the versatile platform is currently
broken in multiple ways. Most importantly, the ports do
not get mapped into the virtual address space at all.
Also, there is some amount of confusion between PCI I/O
space and other statically mapped MMIO registers in the
platform code:
* The __io_address() macro that is used to access the
platform register maps to the same __io macro that gets
used for I/O space.
* The IO_SPACE_LIMIT is set to a value that is much larger
than the total available space.
* The I/O resource of the PCI bus is set to the physical
address of the mapping, which is way outside of the
actual I/O space limit as well as the address range that
gets decoded by traditional PCI cards.
* No attempt is made to stay outside of the ISA port range
that some device drivers try access.
* No resource gets requested as a child of ioport_resource,
but an IORESOURCE_IO type mapping gets requested
as a child of iomem_resource.
This patch attempts to correct all of the above. This makes
it possible to use virtio-pci based virtual devices as well
as actual PCI cards including those with legacy ISA port
ranges like VGA.
Some of the issues seem to be duplicated on other platforms.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[rob: update to 3.5-rc2 and io.h cleanup related changes]
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch switches from static serial driver initialization to devicetree
configuration. This way, the Standard UARTs of the LPC32xx SoC can be enabled
individually via DT.
E.g., instead of Kconfig configuration, the phy3250.dts activates
UARTs 3 and 5.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Remove more custom stuff by simply converting the Nomadik machine
to use generic clocks and move the driver to drivers/clk.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mike Turquette <mturquette@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CMA has been enabled unconditionally on all ARMv6+ systems to solve the
long standing issue of double kernel mappings for all dma coherent
buffers. This however created a dependency on CONFIG_EXPERIMENTAL for
the whole ARM architecture what should be really avoided. This patch
removes this dependency and lets one use old, well-tested dma-mapping
implementation also on ARMv6+ systems without the need to use
EXPERIMENTAL stuff.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPuex7AAoJEIwa5zzehBx3xsQP/jkyt74MvuKUi8pi2zkeMIgn
4XieyqcA0KZjJzfB22q3GIZjNIf/mEIGE4E/3bneVMPh/E2zaiohaXFExBmjNjml
hhzWeZlFGPBjrZsfpIXJIIUhwSI7gX2rjYh4npJmdNhZmy8Y89XnpNJhN1kOwMuV
oN23hPWoSVGbyDMQ0fmHx9GyOL8m7yap+joG13aljDa2OKpQg+pYvdwft+k1K9di
8yPF+qA043UUR7dSsjmTbiCcjZy2eySdCmfOAkEG4inSgxNoM7GBs3MuwZo/veCD
v5WssJqWDbLXtqKn5Uo2bvGWiEcf0xtwOAqhSpbaup3dQFJSWMEenBTtA9UlxFhk
6gdY62O+7k6N0thkxXyLNGkgaGzexZAsK7dM6XSDB+PqD+OSNJS7dvmxZM8tuaRn
rvCM1XWcNeN/dpnLbgwCR12efkwWtJoqqUZUUp/tFFaTo8HriqeAIYk7obnR8s9n
S5x9LeueQGNgaxXJzVdh481YKG/1lqjG/a06HbVgYS4XQvtdA+4khalOefJv10tm
Nkg8+4/8pMthWJfhhlfPUgWFXOXFF2AGPG4su2XwKuFXypO8599lzi7gUQaEZu2U
7caqoWP69KsKvK5iAAmA4DQ2rcsgHd44NXx/8Jjes9ma8knlYjrf42dBH6AZMQBG
69I9sJ1cyqusBwx72NPN
=WeDQ
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc device tree conversions (part 2) from Olof Johansson:
"These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier."
Fix up trivial conflicts due to nearby changes in
drivers/{gpio/gpio,i2c/busses/i2c}-mxs.c
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: dt: tegra: invert status=disable vs status=okay
ARM: dt: tegra: consistent basic property ordering
ARM: dt: tegra: sort nodes based on bus order
ARM: dt: tegra: remove duplicate device_type property
ARM: dt: tegra: consistenly use lower-case for hex constants
ARM: dt: tegra: format regs properties consistently
ARM: dt: tegra: gpio comment cleanup
ARM: dt: tegra: remove unnecessary unit addresses
ARM: dt: tegra: whitespace cleanup
ARM: dt: tegra cardhu: fix typo in SDHCI node name
ARM: dt: tegra: cardhu: register core regulator tps62361
ARM: dt: tegra30.dtsi: Add SMMU node
ARM: dt: tegra20.dtsi: Add GART node
ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra: Add device tree support for AHB
ARM: dts: enable audio support for imx28-evk
ARM: dts: enable i2c device for imx28-evk
i2c: mxs: add device tree probe support
ARM: dts: enable mmc for imx28-evk
...
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
More cleanups, continuing an earlier set with omap and samsung specific
cleanups. These could not go into the first set because they have
dependencies on various other series that in turn depend on the first
cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7UKB
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc cleanups (part 2) from Olof Johansson:
"More cleanups, continuing an earlier set with omap and samsung
specific cleanups. These could not go into the first set because they
have dependencies on various other series that in turn depend on the
first cleanups."
Fixed up conflicts in arch/arm/plat-omap/counter_32k.c due to commit
bd0493eaaf: "move read_{boot,persistent}_clock to the architecture
level" that changed how the persistent clocks were handled. And trivial
conflicts in arch/arm/mach-omap1/common.h due to just independent
changes close to each other.
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
ARM: SAMSUNG: merge plat-s5p into plat-samsung
ARM: SAMSUNG: move options for common s5p into plat-samsung/Kconfig
ARM: SAMSUNG: move setup code for s5p mfc and mipiphy into plat-samsung
ARM: SAMSUNG: move platform device for s5p uart into plat-samsung
ARM: SAMSUNG: move hr timer for common s5p into plat-samsung
ARM: SAMSUNG: move pm part for common s5p into plat-samsung
ARM: SAMSUNG: move interrupt part for common s5p into plat-samsung
ARM: SAMSUNG: move clock part for common s5p into plat-samsung
ARM: S3C24XX: Use common macro to define resources on dev-uart.c
ARM: S3C24XX: move common clock init into common.c
ARM: S3C24XX: move common power-management code to mach-s3c24xx
ARM: S3C24XX: move plat-s3c24xx/dev-uart.c into common.c
ARM: S3C24XX: move plat-s3c24xx/cpu.c
ARM: OMAP2+: Kconfig: convert SOC_OMAPAM33XX to SOC_AM33XX
ARM: OMAP2+: Kconfig: convert SOC_OMAPTI81XX to SOC_TI81XX
GPMC: add ECC control definitions
ARM: OMAP2+: dmtimer: remove redundant sysconfig context restore
ARM: OMAP: AM35xx: convert 3517 detection/flags to AM35xx
ARM: OMAP: AM35xx: remove redunant cpu_is checks for AM3505
ARM: OMAP1: Pass dma request lines in platform data to MMC driver
...
Pull CMA and ARM DMA-mapping updates from Marek Szyprowski:
"These patches contain two major updates for DMA mapping subsystem
(mainly for ARM architecture). First one is Contiguous Memory
Allocator (CMA) which makes it possible for device drivers to allocate
big contiguous chunks of memory after the system has booted.
The main difference from the similar frameworks is the fact that CMA
allows to transparently reuse the memory region reserved for the big
chunk allocation as a system memory, so no memory is wasted when no
big chunk is allocated. Once the alloc request is issued, the
framework migrates system pages to create space for the required big
chunk of physically contiguous memory.
For more information one can refer to nice LWN articles:
- 'A reworked contiguous memory allocator':
http://lwn.net/Articles/447405/
- 'CMA and ARM':
http://lwn.net/Articles/450286/
- 'A deep dive into CMA':
http://lwn.net/Articles/486301/
- and the following thread with the patches and links to all previous
versions:
https://lkml.org/lkml/2012/4/3/204
The main client for this new framework is ARM DMA-mapping subsystem.
The second part provides a complete redesign in ARM DMA-mapping
subsystem. The core implementation has been changed to use common
struct dma_map_ops based infrastructure with the recent updates for
new dma attributes merged in v3.4-rc2. This allows to use more than
one implementation of dma-mapping calls and change/select them on the
struct device basis. The first client of this new infractructure is
dmabounce implementation which has been completely cut out of the
core, common code.
The last patch of this redesign update introduces a new, experimental
implementation of dma-mapping calls on top of generic IOMMU framework.
This lets ARM sub-platform to transparently use IOMMU for DMA-mapping
calls if one provides required IOMMU hardware.
For more information please refer to the following thread:
http://www.spinics.net/lists/arm-kernel/msg175729.html
The last patch merges changes from both updates and provides a
resolution for the conflicts which cannot be avoided when patches have
been applied on the same files (mainly arch/arm/mm/dma-mapping.c)."
Acked by Andrew Morton <akpm@linux-foundation.org>:
"Yup, this one please. It's had much work, plenty of review and I
think even Russell is happy with it."
* 'for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping: (28 commits)
ARM: dma-mapping: use PMD size for section unmap
cma: fix migration mode
ARM: integrate CMA with DMA-mapping subsystem
X86: integrate CMA with DMA-mapping subsystem
drivers: add Contiguous Memory Allocator
mm: trigger page reclaim in alloc_contig_range() to stabilise watermarks
mm: extract reclaim code from __alloc_pages_direct_reclaim()
mm: Serialize access to min_free_kbytes
mm: page_isolation: MIGRATE_CMA isolation functions added
mm: mmzone: MIGRATE_CMA migration type added
mm: page_alloc: change fallbacks array handling
mm: page_alloc: introduce alloc_contig_range()
mm: compaction: export some of the functions
mm: compaction: introduce isolate_freepages_range()
mm: compaction: introduce map_pages()
mm: compaction: introduce isolate_migratepages_range()
mm: page_alloc: remove trailing whitespace
ARM: dma-mapping: add support for IOMMU mapper
ARM: dma-mapping: use alloc, mmap, free from dma_ops
ARM: dma-mapping: remove redundant code and do the cleanup
...
Conflicts:
arch/x86/include/asm/dma-mapping.h
Lots of gpio changes, both to core code and drivers. Changes do touch
architecture code to remove the need for separate arm/gpio.h includes
in most architectures. Some new drivers are added, and a number of
gpio drivers are converted to use irq_domains for gpio inputs used as
interrupts. Device tree support has been amended to allow multiple
gpio_chips to use the same device tree node. Remaining changes are
primarily bug fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=U6hj
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO driver changes from Grant Likely:
"Lots of gpio changes, both to core code and drivers.
Changes do touch architecture code to remove the need for separate
arm/gpio.h includes in most architectures.
Some new drivers are added, and a number of gpio drivers are converted
to use irq_domains for gpio inputs used as interrupts. Device tree
support has been amended to allow multiple gpio_chips to use the same
device tree node.
Remaining changes are primarily bug fixes."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (33 commits)
gpio/generic: initialize basic_mmio_gpio shadow variables properly
gpiolib: Remove 'const' from data argument of gpiochip_find()
gpio/rc5t583: add gpio driver for RICOH PMIC RC5T583
gpiolib: quiet gpiochip_add boot message noise
gpio: mpc8xxx: Prevent NULL pointer deref in demux handler
gpio/lpc32xx: Add device tree support
gpio: Adjust of_xlate API to support multiple GPIO chips
gpiolib: Implement devm_gpio_request_one()
gpio-mcp23s08: dbg_show: fix pullup configuration display
Add support for TCA6424A
gpio/omap: (re)fix wakeups on level-triggered GPIOs
gpio/omap: fix broken context restore for non-OFF mode transitions
gpio/omap: fix missing check in *_runtime_suspend()
gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()
gpio/omap: remove suspend/resume callbacks
gpio/omap: remove retrigger variable in gpio_irq_handler
gpio/omap: remove saved_wakeup field from struct gpio_bank
gpio/omap: remove suspend_wakeup field from struct gpio_bank
gpio/omap: remove saved_fallingdetect, saved_risingdetect
gpio/omap: remove virtual_irq_start variable
...
Conflicts:
drivers/gpio/gpio-samsung.c
Pull timer updates from Thomas Gleixner.
Various trivial conflict fixups in arch Kconfig due to addition of
unrelated entries nearby. And one slightly more subtle one for sparc32
(new user of GENERIC_CLOCKEVENTS), fixed up as per Thomas.
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
timekeeping: Fix a few minor newline issues.
time: remove obsolete declaration
ntp: Fix a stale comment and a few stray newlines.
ntp: Correct TAI offset during leap second
timers: Fixup the Kconfig consolidation fallout
x86: Use generic time config
unicore32: Use generic time config
um: Use generic time config
tile: Use generic time config
sparc: Use: generic time config
sh: Use generic time config
score: Use generic time config
s390: Use generic time config
openrisc: Use generic time config
powerpc: Use generic time config
mn10300: Use generic time config
mips: Use generic time config
microblaze: Use generic time config
m68k: Use generic time config
m32r: Use generic time config
...
Pull the MCA deletion branch from Paul Gortmaker:
"It was good that we could support MCA machines back in the day, but
realistically, nobody is using them anymore. They were mostly limited
to 386-sx 16MHz CPU and some 486 class machines and never more than
64MB of RAM. Even the enthusiast hobbyist community seems to have
dried up close to ten years ago, based on what you can find searching
various websites dedicated to the relatively short lived hardware.
So lets remove the support relating to CONFIG_MCA. There is no point
carrying this forward, wasting cycles doing routine maintenance on it;
wasting allyesconfig build time on validating it, wasting I/O on git
grep'ping over it, and so on."
Let's see if anybody screams. It generally has compiled, and James
Bottomley pointed out that there was a MCA extension from NCR that
allowed for up to 4GB of memory and PPro-class machines. So in *theory*
there may be users out there.
But even James (technically listed as a maintainer) doesn't actually
have a system, and while Alan Cox claims to have a machine in his cellar
that he offered to anybody who wants to take it off his hands, he didn't
argue for keeping MCA support either.
So we could bring it back. But somebody had better speak up and talk
about how they have actually been using said MCA hardware with modern
kernels for us to do that. And David already took the patch to delete
all the networking driver code (commit a5e371f61a: "drivers/net:
delete all code/drivers depending on CONFIG_MCA").
* 'delete-mca' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
MCA: delete all remaining traces of microchannel bus support.
scsi: delete the MCA specific drivers and driver code
serial: delete the MCA specific 8250 support.
arm: remove ability to select CONFIG_MCA
Once again, ixp4xx no longer even compiles. This patch fixes the issue
by converting over to gpiolib. This patch was first made by Imre and
posted by Marc, and I added in Russell's suggestion to empty the gpio
header file.
This fix should also go for 3.1, 3.2, 3.3, and 3.4.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
Power management changes here are mostly for the omap platform, but also
include cpuidle changes for ux500 and suspend/resume code for mmp.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=oGcZ
-----END PGP SIGNATURE-----
Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc power management changes from Olof Johansson:
"Power management changes here are mostly for the omap platform, but
also include cpuidle changes for ux500 and suspend/resume code for
mmp."
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
ARM: OMAP2+: WDTIMER integration: fix !PM boot crash, disarm timer after hwmod reset
ARM: OMAP2/3: hwmod data: Add 32k-sync timer data to hwmod database
ARM: OMAP4: hwmod_data: Name the common irq for McBSP ports
ARM: OMAP4: hwmod data: I2C: add flag for context restore
ARM: OMAP3: hwmod_data: Rename the common irq for McBSP ports
ARM: OMAP2xxx: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP3: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP2+: hwmod data: add HDQ/1-wire hwmod shared data
ARM: OMAP2+: HDQ1W: add custom reset function
ARM: OMAP2420: hwmod data: Add MMC hwmod data for 2420
arm: omap3: clockdomain data: Remove superfluous commas from gfx_sgx_3xxx_wkdeps[]
ARM: OMAP2+: powerdomain: Get rid off duplicate pwrdm_clkdm_state_switch() API
ARM: OMAP3: clock data: add clockdomain for HDQ functional clock
ARM: OMAP3+: dpll: Configure autoidle mode only if it's supported
ARM: OMAP2+: dmtimer: cleanup iclk usage
ARM: OMAP4+: Add prm and cm base init function.
ARM: OMAP2/3: Add idle_st bits for ST_32KSYNC timer to prcm-common header
ARM: OMAP3: Fix CM register bit masks
ARM: OMAP: clock: convert AM3517/3505 detection/flags to AM35xx
ARM: OMAP3: clock data: treat all AM35x devices the same
...
With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. but the payback comes later when adding
new boards can be done by only providing new device trees instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HIfz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game of
booting using device trees, which is a great step forward for them. at91
and spear have pretty much completed this process with a huge amount of
work being put into at91. The other platforms are continuing the process.
We finally start to see the payback on this investment, as new machines
are getting supported purely by adding a .dts source file that can be
completely independent of the kernel source.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7DYv
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull device tree conversions for arm-soc, part 1, from Olof Johansson:
"The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game
of booting using device trees, which is a great step forward for them.
at91 and spear have pretty much completed this process with a huge
amount of work being put into at91. The other platforms are
continuing the process.
We finally start to see the payback on this investment, as new
machines are getting supported purely by adding a .dts source file
that can be completely independent of the kernel source."
Fix up trivial conflict in arch/arm/Kconfig
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: at91: Add ADC driver to at91sam9260/at91sam9g20 dtsi files
arm/dts: omap4-panda: Add LEDs support
arm/dts: omap4-sdp: Add LEDs support
arm/dts: twl4030: Add twl4030-gpio node
OMAP4: devices: Do not create mcpdm device if the dtb has been provided
OMAP4: devices: Do not create dmic device if the dtb has been provided
Documentation: update docs for mmp dt
ARM: dts: refresh dts file for arch mmp
ARM: mmp: support pxa910 with device tree
ARM: mmp: support mmp2 with device tree
gpio: pxa: parse gpio from DTS file
ARM: mmp: support DT in timer
ARM: mmp: support DT in irq
ARM: mmp: append CONFIG_MACH_MMP2_DT
ARM: mmp: fix build issue on mmp with device tree
ARM: ux500: Enable PRCMU Timer 4 (clocksource) for Device Tree
ARM: ux500: Disable SMSC911x platform code registration when DT is enabled
ARM: ux500: Fork cpu-db8500 platform_devs for sequential DT enablement
ARM: ux500: Do not attempt to register non-existent i2c devices on Snowball
ARM: SPEAr3xx: Correct keyboard data passed from DT
...
These bug fixes were not important enough to have them included in the
v3.4 release, mostly because they cover harmless warnings or unrealistic
configurations. Instead we queue them up to be picked up in the next
merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yCUM
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-critical arm-soc bug fixes from Olof Johansson:
"These bug fixes were not important enough to have them included in the
v3.4 release, mostly because they cover harmless warnings or
unrealistic configurations. Instead we queue them up to be picked up
in the next merge window."
Fixed up trivial conflict in arch/arm/mach-omap2/board-omap4panda.c
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: spear6xx: remove board selection options
ARM: OMAP: igep0020: Specify the VPLL2 regulator unconditionally
ARM: OMAP2+: INTC: fix Kconfig option for TI81XX
ARM: OMAP2+: remove incorrect irq_chip ack field
ARM: OMAP4: Adding ID for OMAP4460 ES1.1
ARM: OMAP4: panda: add statics to remove warnings
ARM: OMAP2+: Incorrect Register Offsets in OMAP Mailbox
ARM: OMAP: fix trivial warnings for dspbridge
arm: davinci: use for_each_set_bit_from
ARM: OMAP4: hsmmc: check for null pointer
ARM: OMAP1: fix compilation issue in board-sx1.c
ARM: disable SUSPEND/ARCH_SUSPEND_POSSIBLE for ARCH_TEGRA
ARM: davinci: da850-evm: fix section mismatch
ARM: tegra: add pll_x freq table entry for 750MHz
ARM: davinci: mark spi_board_info arguments as const
ARM: davinci: fix incorrect pdctl next bit position
These cleanups are basically all over the place. The idea is to collect
changes with minimal impact but large number of changes so we can avoid
them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPuemiAAoJEIwa5zzehBx3L9oQAKiu0bsCiT6BM3VC5VGpluk7
YVLH/fkYGdSUTeGrpjeaoxxZnN5M1CLwErg3DxWcyYidy0zfmqitC8t2KQxZMxuf
bt+hn4flpFnXMNm31B9xBCXOOVAvteZHYS35FdSKGyWo5Kz2WKM8ZrrihkAA7jVi
U75x4+shFPtIhLNg2sJg4e/9D1T14ypElB7W989NzxMtco5fbukVd6vDBHPlFDG3
RVI2z2MbWUj3HVmdoyB+09ekruys0MQsbPOGo8D4aeJicrli/JBtL1r1w6ZZ6I8v
Pe0+CbgemMWS69I37Zuxt35Bejpdofa8nKhT1jBrH4uHYxroKkhhx+VMTtuCcFVw
Q2DhbbHImiW3598c0jkGi7Gk+TalTxkStMQiO3bqYAHApftdqFUgkpFSnOC/Jxgj
Y6nUmd+GVPS+r0dDwZg4z5/AnUQd6t8Azp784muPDDxgTV1ZfdaC0LlLjdWesvMO
x+PQib/U7NdxN5lifV6xCXpPoCQsgshrOkVUQiKVHmzaghm9MXgB8qrzXdTz3dLL
XtR3+1KmSDTfHPSlTq/9vIN4RJtsKUnDWzNViTElEql36KzT7l5mJnBe6CJWirJh
7JNyH0p6XDZfc2q7LgdiSU0dv/j9LzBaYUukQCyUI3Tk+5zKgAdKbYNJpRcfPuoO
BK6OKbjCAoAHL+/nDU2s
=Hcjs
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull first batch of arm-soc cleanups from Olof Johansson:
"These cleanups are basically all over the place. The idea is to
collect changes with minimal impact but large number of changes so we
can avoid them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases."
Trivial modify-delete conflicts in arch/arm/mach-{ixp2000,ixp23xx}
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (152 commits)
ARM: clps711x: Cleanup IRQ handling
ARM clps711x: Removed unused header mach/time.h
ARM: clps711x: Added note about support EP731x CPU to Kconfig
ARM: clps711x: Added missing register definitions
ARM: clps711x: Used own subarch directory for store header file
Dove: Fix Section mismatch warnings
ARM: orion5x: ts78xx debugging changes
ARM: orion5x: remove PM dependency from ts78xx
ARM: orion5x: ts78xx fix NAND resource off by one
ARM: orion5x: ts78xx whitespace cleanups
Orion5x: Fix Section mismatch warnings
Orion5x: Fix warning: struct pci_dev declared inside paramter list
ARM: clps711x: Combine header files into one for clps711x-targets
ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
ARM: S5PV210: Use common macro to define resources on dev-audio.c
ARM: S5PC100: Use common macro to define resources on dev-audio.c
ARM: S5P64X0: Use common macro to define resources on dev-audio.c
...
Pull core irq changes from Ingo Molnar:
"A collection of small fixes."
By Thomas Gleixner
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hexagon: Remove select of not longer existing Kconfig switches
arm: Select core options instead of redefining them
genirq: Do not consider disabled wakeup irqs
genirq: Allow check_wakeup_irqs to notice level-triggered interrupts
genirq: Be more informative on irq type mismatch
genirq: Reject bogus threaded irq requests
genirq: Streamline irq_action
Pull smp hotplug cleanups from Thomas Gleixner:
"This series is merily a cleanup of code copied around in arch/* and
not changing any of the real cpu hotplug horrors yet. I wish I'd had
something more substantial for 3.5, but I underestimated the lurking
horror..."
Fix up trivial conflicts in arch/{arm,sparc,x86}/Kconfig and
arch/sparc/include/asm/thread_info_32.h
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
um: Remove leftover declaration of alloc_task_struct_node()
task_allocator: Use config switches instead of magic defines
sparc: Use common threadinfo allocator
score: Use common threadinfo allocator
sh-use-common-threadinfo-allocator
mn10300: Use common threadinfo allocator
powerpc: Use common threadinfo allocator
mips: Use common threadinfo allocator
hexagon: Use common threadinfo allocator
m32r: Use common threadinfo allocator
frv: Use common threadinfo allocator
cris: Use common threadinfo allocator
x86: Use common threadinfo allocator
c6x: Use common threadinfo allocator
fork: Provide kmemcache based thread_info allocator
tile: Use common threadinfo allocator
fork: Provide weak arch_release_[task_struct|thread_info] functions
fork: Move thread info gfp flags to header
fork: Remove the weak insanity
sh: Remove cpu_idle_wait()
...
Pull core ARM updates from Russell King:
"This is the bulk of the core ARM updates for this merge window.
Included in here is a different way to handle the VIVT cache flushing
on context switch, which should allow scheduler folk to remove a
special case in their core code.
We have architectured timer support here, which is a set of timers
specified by the ARM architecture for future SoCs. So we should see
less variability in timer design going forward.
The last big thing here is my cleanup to the way we handle PCI across
ARM, fixing some oddities in some platforms which hadn't realised
there was a way to deal with their private data already built in to
our PCI backend.
I've also removed support for the ARMv3 architecture; it hasn't worked
properly for years so it seems pointless to keep it around."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (47 commits)
ARM: PCI: remove per-pci_hw list of buses
ARM: PCI: dove/kirkwood/mv78xx0: use sys->private_data
ARM: PCI: provide a default bus scan implementation
ARM: PCI: get rid of pci_std_swizzle()
ARM: PCI: versatile: fix PCI interrupt setup
ARM: PCI: integrator: use common PCI swizzle
ARM: 7416/1: LPAE: Remove unused L_PTE_(BUFFERABLE|CACHEABLE) macros
ARM: 7415/1: vfp: convert printk's to pr_*'s
ARM: decompressor: avoid speculative prefetch from non-RAM areas
ARM: Remove ARMv3 support from decompressor
ARM: 7413/1: move read_{boot,persistent}_clock to the architecture level
ARM: Remove support for ARMv3 ARM610 and ARM710 CPUs
ARM: 7363/1: DEBUG_LL: limit early mapping to the minimum
ARM: 7391/1: versatile: add some auxdata for device trees
ARM: 7389/2: plat-versatile: modernize FPGA IRQ controller
AMBA: get rid of last two uses of NO_IRQ
ARM: 7408/1: cacheflush: return error to userspace when flushing syscall fails
ARM: 7409/1: Do not call flush_cache_user_range with mmap_sem held
ARM: 7404/1: cmpxchg64: use atomic64 and local64 routines for cmpxchg64
ARM: 7347/1: SCU: use cpu_logical_map for per-CPU low power mode
...
Sigh, I missed to check which architecture Kconfig files actually
include the core Kconfig file. There are a few which did not. So we
broke them.
Instead of adding the includes to those, we are better off to move the
include to init/Kconfig like we did already with irqs and others.
This does not change anything for the architectures using the old
style periodic timer mode. It just solves the build wreckage there.
For those architectures which use the clock events infrastructure it
moves the include of the core Kconfig file to "General setup" which is
a way more logical place than having it at random locations specified
by the architecture specific Kconfigs.
Reported-by: Ingo Molnar <mingo@kernel.org>
Cc: Anna-Maria Gleixner <anna-maria@glx-um.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is no point having the NET dependency on the select target, as it
forces all users to depend on NET to tell they support BPF_JIT. Move
the config option to the bottom of the file - this could be a nice place
also for future "selectable" config symbols.
Fix up all users to drop the dependency on NET now that it is not
required to supress warnings for non-NET builds.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for CMA to dma-mapping subsystem for ARM
architecture. By default a global CMA area is used, but specific devices
are allowed to have their private memory areas if required (they can be
created with dma_declare_contiguous() function during board
initialisation).
Contiguous memory areas reserved for DMA are remapped with 2-level page
tables on boot. Once a buffer is requested, a low memory kernel mapping
is updated to to match requested memory access type.
GFP_ATOMIC allocations are performed from special pool which is created
early during boot. This way remapping page attributes is not needed on
allocation time.
CMA has been enabled unconditionally for ARMv6+ systems.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
This patch add a complete implementation of DMA-mapping API for
devices which have IOMMU support.
This implementation tries to optimize dma address space usage by remapping
all possible physical memory chunks into a single dma address space chunk.
DMA address space is managed on top of the bitmap stored in the
dma_iommu_mapping structure stored in device->archdata. Platform setup
code has to initialize parameters of the dma address space (base address,
size, allocation precision order) with arm_iommu_create_mapping() function.
To reduce the size of the bitmap, all allocations are aligned to the
specified order of base 4 KiB pages.
dma_alloc_* functions allocate physical memory in chunks, each with
alloc_pages() function to avoid failing if the physical memory gets
fragmented. In worst case the allocated buffer is composed of 4 KiB page
chunks.
dma_map_sg() function minimizes the total number of dma address space
chunks by merging of physical memory chunks into one larger dma address
space chunk. If requested chunk (scatter list entry) boundaries
match physical page boundaries, most calls to dma_map_sg() requests will
result in creating only one chunk in dma address space.
dma_map_page() simply creates a mapping for the given page(s) in the dma
address space.
All dma functions also perform required cache operation like their
counterparts from the arm linear physical memory mapping version.
This patch contains code and fixes kindly provided by:
- Krishna Reddy <vdumpa@nvidia.com>,
- Andrzej Pietrasiewicz <andrzej.p@samsung.com>,
- Hiroshi DOYU <hdoyu@nvidia.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-By: Subash Patel <subash.ramaswamy@linaro.org>
This patch modifies dma-mapping implementation on ARM architecture to
use common dma_map_ops structure and asm-generic/dma-mapping-common.h
helpers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-By: Subash Patel <subash.ramaswamy@linaro.org>
HARDIRQS_SW_RESEND and GENERIC_IRQ_PROBE are already defined as config
switches in the core Kconfig file. Select them instead of defining
them in ARM.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It isn't clear to me why this ever existed, as I've never heard
of an ARM board with an MCA bus. Regardless, the MCA bus support
is going away, so remove the ability to select it from ARM.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'clk-next' of git://git.linaro.org/people/mturquette/linux:
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
ARM: Orion: SDIO: Add support for clk.
ARM: Orion: NAND: Add support for clk, if there is one.
ARM: Orion: EHCI: Add support for enabling clocks
ARM: Orion: SATA: Add per channel clk/clkdev support.
ARM: Orion: UART: Get the clock rate via clk_get_rate().
ARM: Orion: WDT: Add clk/clkdev support
ARM: Orion: Eth: Add clk/clkdev support.
ARM: Orion: SPI: Add clk/clkdev support.
ARM: Orion: Add clocks using the generic clk infrastructure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* clps711x/cleanup:
ARM: clps711x: Cleanup IRQ handling
ARM clps711x: Removed unused header mach/time.h
ARM: clps711x: Added note about support EP731x CPU to Kconfig
ARM: clps711x: Added missing register definitions
ARM: clps711x: Used own subarch directory for store header file
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The nomadik gpio code has been converted to pinctrl, but the nomadik platform
still expects the old code to be present. Change it to use the new one instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
* 'dt' of git://github.com/hzhuang1/linux:
Documentation: update docs for mmp dt
ARM: dts: refresh dts file for arch mmp
ARM: mmp: support pxa910 with device tree
ARM: mmp: support mmp2 with device tree
gpio: pxa: parse gpio from DTS file
ARM: mmp: support DT in timer
ARM: mmp: support DT in irq
ARM: mmp: append CONFIG_MACH_MMP2_DT
ARM: mmp: fix build issue on mmp with device tree
Includes an update to v3-4-rc5
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ep7312 has been supported for a very long time, but has never
been mentioned in the Kconfig file.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Since just plat-samsung can support all of Samsung stuff so
that there is no more need to keep the plat-s5p for S5P SoCs.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
SPEAr SoCs used its own clock framework since now. From now on they will move to
use common clock framework.
This patch updates existing SPEAr machine support to adapt for common clock
framework.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
As the ultimate for mxs platform is to convert over to device tree,
let's start always building in device tree support for the platform.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Rather than requiring architectures that use gpiolib but don't have any
need to define anything custom to copy an asm/gpio.h provide a Kconfig
symbol which architectures must select in order to include gpio.h and
for other architectures just provide the trivial implementation directly.
This makes it much easier to do gpiolib updates and is also a step towards
making gpiolib APIs available on every architecture.
For architectures with existing boilerplate code leave a stub header in
place which warns on direct inclusion of asm/gpio.h and includes
linux/gpio.h to catch code that's doing this. Direct inclusion of
asm/gpio.h has long been deprecated.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jonas Bonn <jonas@southpole.se>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
By Stephen Warren
via Stephen Warren
* 'for-3.5/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: disable SUSPEND/ARCH_SUSPEND_POSSIBLE for ARCH_TEGRA
ARM: tegra: add pll_x freq table entry for 750MHz
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPpvY9AAoJEHm+PkMAQRiGpEoIAJgbu+Y8gITnBK/wh9O6zy3S
5jie5KK4YWdbJsvO58WbNr3CyVIwGIqQ2dUZLiU59aBVLarlGw8xor0MmW+cZwhp
6fBHaf0qDYAV0MZjD+mnnExOiCRyISa2lPmsfu9dAWywh5KGe6/oAP6/qcXIyok3
KZyl3qQf4ENpaZPHwZPXCEkUvtuyHgNiszN+QXEadA3s19Ot4VGe9A3VGw+GNrSm
JqFIq3acQAbKa5BYaqf7TQC02v2FI7//eqt6QHxTqbE6a7LGbTvLfX3HlJ2mnfqa
1R6QHhM4y4OZDHbaMT2raHZ8WuLXzhehJzhP8Co7AHFOKwVKOb5XbcUr2RrukMU=
=HkMd
-----END PGP SIGNATURE-----
Merge tag 'v3.4-rc6' into next/cleanup
Linux 3.4-rc6
Resolve conflict where an u5500 file had a bugfix go in, but was
deleted in the branch staged for next merge window.
Signed-off-by: Olof Johansson <olof@lixom.net>
"Jean-Christophe PLAGNIOL-VILLARD" <plagnioj@jcrosoft.com> writes:
ARM: AT91 more DT material
New SoC conversion and boards support
SoC convertion to DT:
- at91sam9260
- at91sam9263
boards:
- Atmel at91sam9g20ek/9263ek
- Calao TNY-A9260/A9263/A9G20
- Calao USB-A9260/A9263
- Ethernnut 5
- Kizbox
* tag 'at91-for-next-dt' of git://github.com/at91linux/linux-at91: (32 commits)
Ethernut 5 board support
ARM: at91: add kizbox board dt support.
ARM: at91: DT: add Calao TNY A9263 board support
ARM: at91: DT: add Calao USB A9263 board support
ARM: at91: add at91sam9263ek DT support
ARM: at91: add at91sam9263 DT support
ARM: at91: standard device init only if DT is not populated.
ARM: at91: DT: add Calao USB A9260 DT support
ARM: at91: Calao USB A926x factorize common binding in usb_a9260_common
ARM: at91: USB A926x update nand partition
ARM: at91: add at91sam9g20ek boards dt support
arm: at91: add Calao TNY-A9260 and TNY-A9G20 board support
ARM: at91: add at91sam9260 DT support
ARM: at91: add defconfig for device tree
ARM: at91/dt: do not specify the board any more
ARN: at91: introduce SOC_AT91xxx define to allow to compile SoC core support
ARM: at91: add SOC_AT91SAM9 kconfig option to factorise select
ARM: at91: pm select memory controler at runtime
ARM: at91: move at91_init_leds to board init
ARM: at91: do not pin mux the UARTs in init_early
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
Add tclk as a fixed rate clock for all platforms. In addition, on
kirkwood, add a gated clock for most of the clocks which can be gated.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
[mturquette@linaro.org: removed redundant CLKDEV_LOOKUP from Kconfig]
[mturquette@linaro.org: removed redundant clk.h from mach-dove/common.c]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
cpuidle uses a generic function now. Remove the unused code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/20120507175652.260797846@linutronix.de
When enable ARCH_SUSPEND_POSSIBLE, it need defintion of
cpu_mohawk_do_suspend and cpu_mohawk_do_resume
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <<haojian.zhuang@gmail.com>
Same code. Use the generic version. The special Makefile treatment is
pointless anyway as init_task.o contains only data which is handled by
the linker script. So no point on being treated like head text.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Russell King <linux@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/20120503085034.221811388@linutronix.de
Merge irq-pxa168 and irq-mmp2. And support device tree also.
Since CONFIG_SPARSE_IRQ is enabled in arch-mmp, base irq starts from
NR_IRQS_LEGACY.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This does two things to the FPGA IRQ controller in the versatile
family:
- Convert to MULTI_IRQ_HANDLER so we can drop the entry macro
from the Integrator. The C IRQ handler was inspired from
arch/arm/common/vic.c, recent bug discovered in this handler was
accounted for.
- Convert to using IRQ domains so we can get rid of the NO_IRQ
mess and proceed with device tree and such stuff.
As part of the exercise, bump all the low IRQ numbers on the
Integrator PIC to start from 1 rather than 0, since IRQ 0 is
now NO_IRQ. The Linux IRQ numbers are thus entirely decoupled
from the hardware IRQ numbers in this controller.
I was unable to split this patch. The main reason is the half-done
conversion to device tree in Versatile.
Tested on Integrator/AP and Integrator/CP.
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the A15 generic timer and clocksource.
As the timer generates interrupts on a different PPI depending
on the execution mode (normal or secure), it is possible to
register two different PPIs.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Tested-by: Frank Rowand <frank.rowand@am.sony.com>
Link: http://lkml.kernel.org/r/20120420124557.448826362@linutronix.de
Add calls to tracehook_report_syscall_{entry,exit} and tracehook_signal_handler
Signed-off-by: Steven Walter <stevenrwalter@gmail.com>
Signed-off-by: Wade Farnsworth <wade_farnsworth@mentor.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In 3872c48b (tick: Document TICK_ONESHOT config option) Thomas describes
the circumstances under which TICK_ONESHOT should be selected. This is
an internal time keeping configuration symbol which should not be
selected by platform or arch code. So remove our select statements for
it.
This kills these warnings in OMAP builds:
kernel/time/tick-sched.c:47: warning: 'tick_do_update_jiffies64' defined but not used
kernel/time/tick-sched.c:89: warning: 'tick_init_jiffy_update' defined but not used
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Erratum #326103 ("FSR write bit incorrect on a SWP to read-only memory")
only affects the ARM 1136 core prior to r1p0. The workaround
disassembles the faulting instruction to determine whether it was a read
or write access on all v6 cores.
An issue has been reported on the ARM 11MPCore whereby loading the
faulting instruction may happen in parallel with that page being
unmapped, resulting in a deadlock due to the lack of TLB broadcasting
in hardware:
http://lists.infradead.org/pipermail/linux-arm-kernel/2012-March/091561.html
This patch limits the workaround so that it is only used on affected
cores, which are known to be UP only. Other v6 cores can rely on the
FSR to indicate the access type correctly.
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- The biggest improvement of this series is the ability to compile several
AT91 SoCs in one kernel image.
For now on it's limited to the DT-enabled boards but we can compile all
the core together.
- The Kconfig series is stacked before other patches as it is simple and
non-intrusive. Its goal is to remove too restrictive dependencies on
SoC names. This will allow to add support for newer SoC seamlessly.
- Some very "cosmetic" Kconfig changes are also added (entry names,
comments, etc.).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPjYz4AAoJEAf03oE53VmQ/0wH/3kXJYM/8nX8fqlQ8eTh0SHi
lRsoNL+4arHFKcocYhZyiXEidUKCUMLuQSdvL9MWy1e286+ABsaFgrjfLsp/ZDqE
jDJBCZIxUD6rL94VRnYEHrhWqGzzPKi8/syVZ8JOv/1HGml402CqPcRDKmWY/e4Q
ajl/d463q0ufwfQ4LMP+DsR29TxEdecs4DkxnhwcrRCbJ2hDPLmWVER+tPITPwqp
R8qVGY3K6axG68b964B/hsACjRF7C1lqRQsiQbi8pVPPGEhekmgnW8hF6dNdy1VW
wVo8F0GCST6jLk9YFbirBdKsDRJTLc+WsyP6jUZyWkrrM6p4ycs+voGFDNZbhPw=
=CXyd
-----END PGP SIGNATURE-----
Merge tag 'at91-3.5-cleanup' of git://github.com/at91linux/linux-at91 into next/cleanup
Nicolas Ferre <nicolas.ferre@atmel.com> writes:
First batch of AT91 cleanup for 3.5 kernel.
- The biggest improvement of this series is the ability to compile several
AT91 SoCs in one kernel image.
For now on it's limited to the DT-enabled boards but we can compile all
the core together.
- The Kconfig series is stacked before other patches as it is simple and
non-intrusive. Its goal is to remove too restrictive dependencies on
SoC names. This will allow to add support for newer SoC seamlessly.
- Some very "cosmetic" Kconfig changes are also added (entry names,
comments, etc.).
* tag 'at91-3.5-cleanup' of git://github.com/at91linux/linux-at91: (19 commits)
ARM: at91: add defconfig for device tree
ARM: at91/dt: do not specify the board any more
ARN: at91: introduce SOC_AT91xxx define to allow to compile SoC core support
ARM: at91: add SOC_AT91SAM9 kconfig option to factorise select
ARM: at91: pm select memory controler at runtime
ARM: at91: move at91_init_leds to board init
ARM: at91: do not pin mux the UARTs in init_early
ARM: at91: drop at91_set_serial_console
ARM: at91: uncompress: autodetect the uart to use
ARM: at91: uncompress Store UART address in a variable
hwrng: Kconfig: remove dependency for atmel-rng driver
Input: Kconfig: remove dependency for atmel_tsadcc driver
rtc: Kconfig: remove dependency for AT91 rtc driver
ARM: at91/Kconfig: website link for AT91SAM9G20-EK
ARM: at91/Kconfig: add AT91SAM9x5 family to AT91_EARLY_DBGU0 entry
ARM: at91/Kconfig: add clarifications to AT91SAM9M10G45-EK entry
ARM: at91/Kconfig: add comment to at91sam9x5 family entry
ARM: at91/Kconfig: change at91sam9g45 entry
ARM: at91: change AT91 Kconfig entry comment
Also updates the cleanup branch to v3.4-rc3.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These kconfig entries are already defined in kernel/irq/Kconfig
so select them instead of redefining them.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ixp2xxx platforms have had no real changes since ~2006 and the maintainer
has said on irc that they can be removed:
13:05 < nico> do you still care about ixp2000?
13:22 < lennert> not really, no
13:58 < nico> do you think we could remove it from the kernel tree?
14:01 < lennert> go for it, and remove ixp23xx too while you're at it
Removing will help simplify ARM consolidation in general and PCI re-work
specifically.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
With commit c334bc1 (ARM: make mach/io.h include optional), PCMCIA was
broken. PCMCIA depends on __io() returning a valid i/o address, and most
ARM platforms require IO_SPACE_LIMIT be set to 0xffffffff for PCMCIA. This
needs a better fix with a fixed i/o address mapping, but for now we just
restore things to the previous behavior.
This fixes at91, omap1, pxa and sa11xx. pxa needs io.h if PCI is enabled,
but PCMCIA is not. sa11xx already has IO_SPACE_LIMIT set to 0xffffffff,
so it doesn't need an io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Joachim Eastwood <joachim.eastwood@jotron.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com> (pxa270)
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Rob Herring has done a sweeping change cleaning up all of the mach/io.h includes,
moving some of the oft-repeated macros to a common location and removing a bunch of
boiler plate. This is another step closer to a common zImage for multiple platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YIsn
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: cleanups of io includes" from Olof Johansson:
"Rob Herring has done a sweeping change cleaning up all of the
mach/io.h includes, moving some of the oft-repeated macros to a common
location and removing a bunch of boiler plate. This is another step
closer to a common zImage for multiple platforms."
Fix up various fairly trivial conflicts (<mach/io.h> removal vs changes
around it, tegra localtimer.o is *still* gone, yadda-yadda).
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: tegra: Include assembler.h in sleep.S to fix build break
ARM: pxa: use common IOMEM definition
ARM: dma-mapping: convert ARCH_HAS_DMA_SET_COHERENT_MASK to kconfig symbol
ARM: __io abuse cleanup
ARM: create a common IOMEM definition
ARM: iop13xx: fix missing declaration of iop13xx_init_early
ARM: fix ioremap/iounmap for !CONFIG_MMU
ARM: kill off __mem_pci
ARM: remove bunch of now unused mach/io.h files
ARM: make mach/io.h include optional
ARM: clps711x: remove unneeded include of mach/io.h
ARM: dove: add explicit include of dove.h to addr-map.c
ARM: at91: add explicit include of hardware.h to uncompressor
ARM: ep93xx: clean-up mach/io.h
ARM: tegra: clean-up mach/io.h
ARM: orion5x: clean-up mach/io.h
ARM: davinci: remove unneeded mach/io.h include
[media] davinci: remove includes of mach/io.h
ARM: OMAP: Remove remaining includes for mach/io.h
ARM: msm: clean-up mach/io.h
...
Pull more ARM updates from Russell King.
This got a fair number of conflicts with the <asm/system.h> split, but
also with some other sparse-irq and header file include cleanups. They
all looked pretty trivial, though.
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (59 commits)
ARM: fix Kconfig warning for HAVE_BPF_JIT
ARM: 7361/1: provide XIP_VIRT_ADDR for no-MMU builds
ARM: 7349/1: integrator: convert to sparse irqs
ARM: 7259/3: net: JIT compiler for packet filters
ARM: 7334/1: add jump label support
ARM: 7333/2: jump label: detect %c support for ARM
ARM: 7338/1: add support for early console output via semihosting
ARM: use set_current_blocked() and block_sigmask()
ARM: exec: remove redundant set_fs(USER_DS)
ARM: 7332/1: extract out code patch function from kprobes
ARM: 7331/1: extract out insn generation code from ftrace
ARM: 7330/1: ftrace: use canonical Thumb-2 wide instruction format
ARM: 7351/1: ftrace: remove useless memory checks
ARM: 7316/1: kexec: EOI active and mask all interrupts in kexec crash path
ARM: Versatile Express: add NO_IOPORT
ARM: get rid of asm/irq.h in asm/prom.h
ARM: 7319/1: Print debug info for SIGBUS in user faults
ARM: 7318/1: gic: refactor irq_start assignment
ARM: 7317/1: irq: avoid NULL check in for_each_irq_desc loop
ARM: 7315/1: perf: add support for the Cortex-A7 PMU
...
Pull ARM platform updates from Russell King:
"This covers platform stuff for platforms I have a direct interest in
(iow, I have the hardware). Essentially:
- as we no longer support any other Acorn platforms other than RiscPC
anymore, we can collect all that code into mach-rpc.
- convert Acorn expansion card stuff to use IRQ allocation functions,
and get rid of NO_IRQ from there.
- cleanups to the ebsa110 platform to move some private stuff out of
its header files.
- large amount of SA11x0 updates:
- conversion of private DMA implementation to DMA engine support
(this actually gives us greater flexibility in drivers over the old
API.)
- re-worked ucb1x00 updates - convert to genirq, remove sa11x0
dependencies, fix various minor issues
- move platform specific sa11x0 framebuffer data into platform files
in arch/arm instead of keeping this in the driver itself
- update sa11x0 IrDA driver for DMA engine, and allow it to use DMA
for SIR transmissions as well as FIR
- rework sa1111 support for genirq, and irq allocation
- fix sa1111 IRQ support so it works again
- use sparse IRQ support
After this, I have one more pull request remaining from my current
set, which I think is going to be the most problematical as it
generates 8 conflicts."
Fixed up the trivial conflict in arch/arm/mach-rpc/Makefile as per
Russell.
* 'platforms' of git://git.linaro.org/people/rmk/linux-arm: (125 commits)
ARM: 7343/1: sa11x0: convert to sparse IRQ
ARM: 7342/2: sa1100: prepare for sparse irq conversion
ARM: 7341/1: input: prepare jornada720 keyboard and ts for sa11x0 sparse irq
ARM: 7340/1: rtc: sa1100: include mach/irqs.h instead of asm/irq.h
ARM: sa11x0: remove unused DMA controller definitions
ARM: sa11x0: remove old SoC private DMA driver
USB: sa1111: add hcd .reset method
USB: sa1111: add OHCI shutdown methods
USB: sa1111: reorganize ohci-sa1111.c
USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__)
USB: sa1111: sparse and checkpatch cleanups
ARM: sa11x0: don't static map sa1111
ARM: sa1111: use dev_err() rather than printk()
ARM: sa1111: cleanup sub-device registration and unregistration
ARM: sa1111: only setup DMA for DMA capable devices
ARM: sa1111: register sa1111 devices with dmabounce in bus notifier
ARM: sa1111: move USB interface register definitions to ohci-sa1111.c
ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c
ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c
ARM: sa1111: delete unused physical GPIO register definitions
...
Most of these patches convert code from using static platform data to
describing the hardware in the device tree. This is only the first
half of the changes for v3.4 because a lot of patches for this topic
came in the last week before the merge window.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fMC+
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: device tree work" from Arnd Bergmann:
"Most of these patches convert code from using static platform data to
describing the hardware in the device tree. This is only the first
half of the changes for v3.4 because a lot of patches for this topic
came in the last week before the merge window.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fix up trivial conflicts in arch/arm/mach-vexpress/{Kconfig,core.h}
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (86 commits)
Document: devicetree: add OF documents for arch-mmp
ARM: dts: append DTS file of pxa168
ARM: mmp: append OF support on pxa168
ARM: mmp: enable rtc clk in pxa168
i2c: pxa: add OF support
serial: pxa: add OF support
arm/dts: mt_ventoux: very basic support for TeeJet Mt.Ventoux board
ARM: OMAP2+: Remove extra ifdefs for board-generic
ARM: OMAP2+: Fix build error when only ARCH_OMAP2/3 or 4 is selected
ASoC: DT: Add digital microphone binding to PAZ00 board.
ARM: dt: Add ARM PMU to tegra*.dtsi
ARM: at91: at91sam9x5cm/dt: add leds support
ARM: at91: usb_a9g20/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add leds support
ARM: at91: usb_a9g20/dt: add leds support
ARM: at91/pio: add new PIO3 features
ARM: at91: add sam9_smc.o to at91sam9x5 build
ARM: at91/tc/clocksource: Add 32 bit variant to Timer Counter
ARM: at91/tc: add device tree support to atmel_tclib
...
These are all specific to some driver. They are typically the platform
side of a change in the drivers directory, such as adding a new driver
or extending the interface to the platform. In cases where there is no
maintainer for the driver, or the maintainer prefers to have the
platform changes in the same branch as the driver changes, the patches
to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in fuse.c.
In rtc-sa1100.c, the global removal of IRQF_DISABLED conflicts with
the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pQ3X
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: driver specific updates" from Arnd Bergmann:
"These are all specific to some driver. They are typically the
platform side of a change in the drivers directory, such as adding a
new driver or extending the interface to the platform. In cases where
there is no maintainer for the driver, or the maintainer prefers to
have the platform changes in the same branch as the driver changes,
the patches to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in
fuse.c. In rtc-sa1100.c, the global removal of IRQF_DISABLED
conflicts with the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up aforementioned trivial conflicts.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: SAMSUNG: change the name from s3c-sdhci to exynos4-sdhci
mmc: sdhci-s3c: add platform data for the second capability
ARM: SAMSUNG: support the second capability for samsung-soc
ARM: EXYNOS: add support DMA for EXYNOS4X12 SoC
ARM: EXYNOS: Add apb_pclk clkdev entry for mdma1
ARM: EXYNOS: Enable MDMA driver
regulator: Remove bq24022 regulator driver
rtc: sa1100: add OF support
pxa: magician/hx4700: Convert to gpio-regulator from bq24022
ARM: OMAP3+: SmartReflex: fix error handling
ARM: OMAP3+: SmartReflex: fix the use of debugfs_create_* API
ARM: OMAP3+: SmartReflex: micro-optimization for sanity check
ARM: OMAP3+: SmartReflex: misc cleanups
ARM: OMAP3+: SmartReflex: move late_initcall() closer to its argument
ARM: OMAP3+: SmartReflex: add missing platform_set_drvdata()
ARM: OMAP3+: hwmod: add SmartReflex IRQs
ARM: OMAP3+: SmartReflex: clear ERRCONFIG_VPBOUNDINTST only on a need
ARM: OMAP3+: SmartReflex: Fix status masking in ERRCONFIG register
ARM: OMAP3+: SmartReflex: Add a shutdown hook
ARM: OMAP3+: SmartReflex Class3: disable errorgen before disable VP
...
Conflicts:
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/fuse.c
drivers/rtc/rtc-sa1100.c
These changes are all specific to one board only. We're trying to keep
the number of board files low, but generally board level updates are
ok on platforms that are working on moving towards DT based probing,
which will eventually lead to removing them.
The board-ams-delta.c board file gets a conflict between the removal of
ams_delta_config and the addition of a lot of other data. The Kconfig
file has two changes in the same line, and in exynos, the power domain
cleanup conflicts with the addition of the image sensor device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: Amended a fix for a mismerge to board-omap4panda.c]
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HPiJ
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: board specific updates" from Arnd Bergmann/Olof Johansson:
"These changes are all specific to one board only. We're trying to
keep the number of board files low, but generally board level updates
are ok on platforms that are working on moving towards DT based
probing, which will eventually lead to removing them.
The board-ams-delta.c board file gets a conflict between the removal
of ams_delta_config and the addition of a lot of other data. The
Kconfig file has two changes in the same line, and in exynos, the
power domain cleanup conflicts with the addition of the image sensor
device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: Amended a fix for a mismerge to board-omap4panda.c]
Signed-off-by: Olof Johansson <olof@lixom.net>"
Fixed up some fairly trivial conflicts manually.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (82 commits)
i.MX35-PDK: Add Camera support
ARM : mx35: 3ds-board: add framebuffer device
pxa/hx4700: Remove pcmcia platform_device structure
ARM: pxa/hx4700: Reduce sleep mode battery discharge by 35%
ARM: pxa/hx4700: Remove unwanted request for GPIO105
ARM: EXYNOS: support Exynos4210-bus Devfreq driver on Nuri board
ARM: EXYNOS: Register JPEG on nuri
ARM: EXYNOS: Register JPEG on universal_c210
ARM: S5PV210: Enable JPEG on SMDKV210
ARM: S5PV210: Add JPEG board definition
ARM: EXYNOS: Enable JPEG on Origen
ARM: EXYNOS: Enable JPEG on SMDKV310
ARM: EXYNOS: Add __init attribute to universal_camera_init()
ARM: EXYNOS: Add __init attribute to nuri_camera_init()
ARM: S5PV210: Enable FIMC on SMDKC110
ARM: S5PV210: Enable FIMC on SMDKV210
ARM: S5PV210: Enable MFC on SMDKC110
ARM: S5PV210: Enable MFC on SMDKV210
ARM: EXYNOS: Enable G2D on SMDKV310
ARM: tegra: update defconfig
...
These changes are all specific to an soc family or the code for
one soc. Lots of work for Tegra3 this time, but also a lot of other
platforms. There will be another (smaller) set of soc patches later in
the merge window for stuff that has dependencies on external trees or
that was sent just before the merge window opened.
The asoc tree added a few devices to the i.mx platform, which conflict
with other devices added in the same place here.
The tegra Makefile conflicts between a number of branches, mostly because
of changes regarding localtimer.c, which was removed in the end.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WdYR
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: SoC specific updates" from Arnd Bergmann:
"These changes are all specific to an soc family or the code for one
soc. Lots of work for Tegra3 this time, but also a lot of other
platforms. There will be another (smaller) set of soc patches later
in the merge window for stuff that has dependencies on external trees
or that was sent just before the merge window opened.
The asoc tree added a few devices to the i.mx platform, which conflict
with other devices added in the same place here.
The tegra Makefile conflicts between a number of branches, mostly
because of changes regarding localtimer.c, which was removed in the
end.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fix up some trivial conflicts, including the mentioned Tegra Makefile.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: EXYNOS: fix cycle count for periodic mode of clock event timers
ARM: EXYNOS: add support JPEG
ARM: EXYNOS: Add DMC1, allow PPMU access for DMC
ARM: SAMSUNG: Correct MIPI-CSIS io memory resource definition
ARM: SAMSUNG: fix __init attribute on regarding s3c_set_platdata()
ARM: SAMSUNG: Add __init attribute to samsung_bl_set()
ARM: S5PV210: Add usb otg phy control
ARM: S3C64XX: Add usb otg phy control
ARM: EXYNOS: Enable l2 configuration through device tree
ARM: EXYNOS: remove useless code to save/restore L2
ARM: EXYNOS: save L2 settings during bootup
ARM: S5P: add L2 early resume code
ARM: EXYNOS: Add support AFTR mode on EXYNOS4210
ARM: mx35: Setup the AIPS registers
ARM: mx5: Use common function for configuring AIPS
ARM: mx3: Setup AIPS registers
ARM: mx3: Let mx31 and mx35 enter in LPM mode in WFI
ARM: defconfig: imx_v6_v7: build in REGULATOR_FIXED_VOLTAGE
ARM: imx: update imx_v6_v7_defconfig
ARM: tegra: Demote EMC clock inconsistency BUG to WARN
...
Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=o5Xl
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: global cleanups" from Arnd Bergmann:
"Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up trivial conflicts mainly due to #include's being changes on
both sides.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
ARM: OMAP2+: Fix build error after merge
ARM: S3C24XX: remove call to s3c24xx_setup_clocks
...
Simple bug fixes that were not considered important enough for inclusion
into 3.3. One bug fix was originally intended for 3.3 but accidentally
got missed, but is not marked stable because it should only get
backported once later fixes also make it into v3.4.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=eLYz
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: Non-critical bug fixes" from Ardn Bergmann:
"Simple bug fixes that were not considered important enough for
inclusion into 3.3. One bug fix was originally intended for 3.3 but
accidentally got missed, but is not marked stable because it should
only get backported once later fixes also make it into v3.4.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (66 commits)
iomux-mx25.h slew rate adjusted for LCD __LD pins
ARM: davinci: DA850: move da850_register_pm to .init.text
ARM: davinci: cpufreq: fix compiler warning
ARM: OMAP2+: Fix build for omap4 only builds with missing include of linux/bug.h
ARM: OMAP2+: Fix section warnings for hsmmc_init_one
ARM: OMAP2+: Fix build issues with missing include of linux/bug.h
ARM: OMAP2+: gpmc-smsc911x: only register regulator for first instance
ARM: OMAP3+: PM: VP: fix integer truncation error
ARM: OMAP2+: PM: fix wakeupgen warning when hotplug disabled
ARM: OMAP2+: PM: fix section mismatch with omap2_init_processor_devices()
ARM: OMAP2: Fix section warning for n8x0 when CONFIG_MMC_OMAP is not set
ARM: OMAP2+: Fix omap24xx_io_desc warning if SoC subtypes are not selected
ARM: OMAP1: Fix section mismatch for omap1_init_early()
ARM: OMAP1: Fix typo in lcd_dma.c
ARM: OMAP: mailbox: trivial whitespace fix
ARM: OMAP: Remove definition cpu_is_omap4430()
ARM: OMAP2+: included some headers twice
ARM: OMAP: clock.c: included linux/debugfs.h twice
ARM: OMAP: don't build hwspinlock in vain
ARM: OMAP2+: ads7846_init: put gpio_pendown into pdata if it's provided
...
Last night's randconfig and the allnoconfig builds spat out the
following warning while building:
warning: (ARM) selects HAVE_BPF_JIT which has unmet direct dependencies (NET)
Acked-by: Mircea Gherzan <mgherzan@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The only users of ARCH_HAS_DMA_SET_COHERENT_MASK are 2 ARM platforms:
ixp4xx and pxa cm_x2xx. We've been getting lucky that the define is
implicitly included before dma-mapping.h, but the removal of io.h broke
things (c334bc1 ARM: make mach/io.h include optional). Since memory.h
is the correct place, but no longer exists, convert the define to a
kconfig entry.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
This converts the Integrator AP/CP to use sparse IRQs.
Tested on both machines.
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Based of Matt Evans's PPC64 implementation.
The compiler generates ARM instructions but interworking is
supported for Thumb2 kernels.
Supports both little and big endian. Unaligned loads are emitted
for ARMv6+. Not all the BPF opcodes that deal with ancillary data
are supported. The scratch memory of the filter lives on the stack.
Hardware integer division is used if it is available.
Enabled in the same way as for x86-64 and PPC64:
echo 1 > /proc/sys/net/core/bpf_jit_enable
A value greater than 1 enables opcode output.
Signed-off-by: Mircea Gherzan <mgherzan@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the arch-specific code to support jump labels for ARM and Thumb-2.
This code will only be activated on compilers that are capable of
building it. It has been tested with GCC 4.6 patched with the patch
from GCC bug 48637.
Cc: Jason Baron <jbaron@redhat.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On Versatile Express, the PCI Express buses are broken and unusable, so
we aren't going to support PCI/ISA IO cycles on this platform. Remove
the PCI/ISA IO inb et.al. support for this platform.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull #1 ARM updates from Russell King:
"This one covers stuff which Arnd is waiting for me to push, as this is
shared between both our trees and probably other trees elsewhere.
Essentially, this contains:
- AMBA primecell device initializer updates - mostly shrinking the
size of the device declarations in platform code to something more
reasonable.
- Getting rid of the NO_IRQ crap from AMBA primecell stuff.
- Nicolas' idle cleanups. This in combination with the restart
cleanups from the last merge window results in a great many
mach/system.h files being deleted."
Yay: ~80 files, ~2000 lines deleted.
* 'for-armsoc' of git://git.linaro.org/people/rmk/linux-arm: (60 commits)
ARM: remove disable_fiq and arch_ret_to_user macros
ARM: make entry-macro.S depend on !MULTI_IRQ_HANDLER
ARM: rpc: make default fiq handler run-time installed
ARM: make arch_ret_to_user macro optional
ARM: amba: samsung: use common amba device initializers
ARM: amba: spear: use common amba device initializers
ARM: amba: nomadik: use common amba device initializers
ARM: amba: u300: use common amba device initializers
ARM: amba: lpc32xx: use common amba device initializers
ARM: amba: netx: use common amba device initializers
ARM: amba: bcmring: use common amba device initializers
ARM: amba: ep93xx: use common amba device initializers
ARM: amba: omap2: use common amba device initializers
ARM: amba: integrator: use common amba device initializers
ARM: amba: realview: get rid of private platform amba_device initializer
ARM: amba: versatile: get rid of private platform amba_device initializer
ARM: amba: vexpress: get rid of private platform amba_device initializer
ARM: amba: provide common initializers for static amba devices
ARM: amba: make use of -1 IRQs warn
ARM: amba: u300: get rid of NO_IRQ initializers
...
Conflicts:
arch/arm/mach-lpc32xx/clock.c
arch/arm/mach-pxa/pxa25x.c
arch/arm/mach-pxa/pxa27x.c
The conflicts with pxa are non-obvious, we have multiple branches
adding and removing the same clock settings. According to
Haojian Zhuang, removing the sa1100 rtc dummy clock is the correct
fix here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'ep93xx-for-arm-soc' of git://github.com/RyanMallon/linux-2.6:
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
(update to v3.3-rc7)
Conflicts:
arch/arm/mach-s3c2440/common.h
The S3C2416 now reuses the dma selection of the S3C2443.
Therefore it is not necessary to keep the S3C2416_DMA option around.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add a kconfig option NEED_MACH_IO_H to conditionally include mach/io.h.
Basing this on CONFIG_PCI and CONFIG_ISA doesn't quite work. Most ISA
platforms don't need mach/io.h, but ebsa110 does. Most PCI platforms need
mach/io.h for now, but ks8695 doesn't which means i/o accesses are broken.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
This patch moves S3C2443 stuff into mach-s3c24xx/ directory
so that we can merge the s3c24 series' directories to the
just one mach-s3c24xx/ directory.
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves S3C2410 stuff into mach-s3c24xx/ directory
so that we can merge the s3c24 series' directories to the
just one mach-s3c24xx/ directory.
And this patch is including following.
- re-ordered alphabetically by option text at Kconfig and Makefile
- removed unused option, MACH_N35
- fixed duplcated option name, S3C2410_DMA to S3C24XX_DMA which is
in plat-s3c24xx/
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the ARCH name to "ARCH_S3C24XX" for Samsung
S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443,
and S3C2450 SoCs so that we can merge the mach-xxx directories
and plat-s3c24xx dir. to just one mach-s3c24xx for them.
I think this should be sent to upstream via samsung tree because
this touches many samsung stuff.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
[for the gadget part:]
Acked-by: Felipe Balbi <balbi@ti.com>
[for the framebuffer (video) part:]
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
[For the watchdog-part:]
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add an irqdomain for the AIC interrupt controller.
The device tree support is mapping the registers and
is using the irq_domain_add_legacy() to manage hwirq
translation.
The documentation is describing the meaning of the
two cells required for using this "interrupt-controller"
in a device tree node.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix L4_EMU_34XX_BASE error after iomap changes
ARM: OMAP2+: Limit omap_read/write usage to legacy USB drivers
ARM: OMAP: Remove plat/io.h by splitting it into mach/io.h and mach/hardware.h
ARM: OMAP2+: Move most of plat/io.h into local iomap.h
ARM: OMAP1: Move most of plat/io.h into local iomap.h
ARM: OMAP1: Move 16xx GPIO system clock to platform init code
ARM: OMAP: Move omap_init_consistent_dma_size() to local common.h
ARM: OMAP2+: Move SDRC related functions from io.h into local common.h
ARM: OMAP2+: Drop DISPC L3 firewall code
ARM: OMAP2xxx: PM: remove obsolete timer disable code in the suspend path
ARM: OMAP: McSPI: Remove unused flag from struct omap2_mcspi_device_config
(update to latest rmk/for-arm-soc branch)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is no way to build U8500 kernels without an MMU
at this point because of dependencies on MMU-only functions.
As long as nobody is interested in fixing this, let's just disable
the platforms for nommu kernels.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is due to the increased number of AB8500 GPIOs.
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The hx4700 platform has 72 board gpios: 64 ASIC3 gpios numbered 192..255, and
8 EGPIO gpios numbered 256..263 (plus a 9th which is not used).
Thus the new CONFIG_ARCH_NR_GPIO config option must be set to 264.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Add rtc clock support and clean clock support for gpio.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Erratum #743622 affects all r2 variants of the Cortex-A9 processor, so
ensure that the workaround is applied regardless of the revision.
Cc: <stable@vger.kernel.org>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only 3 platforms need arch_ret_to_user macro, so add ARCH_HAS_RET_TO_USER
kconfig option and make iop13xx, iop32x and iop33x select it.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Add a sched_clock support for the sp804 timer. The clocksource timer
can optionally initialize itself as sched_clock timer.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Following removal announce and addition to feature-removal-schedule.txt,
here is the actual source code deletion for Atmel CAP9 family.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
All sched_clock() providers have been converted to the sched_clock
framework, which also provides a jiffy based implementation for
the platforms that do not provide a counter.
It is now possible to make the sched_clock framework mandatory,
effectively preventing new platforms to add new sched_clock()
functions, which would be detrimental to the single zImage work.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Prima2 has its own sched_clock() implementation, which gets in the
way of a single zImage. Moving to the common sched_clock framework
makes the code slightly cleaner (the mapping hack in sched_clock()
goes away...).
Acked-by: Barry Song <baohua.song@csr.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Davinci has its own sched_clock() implementation, which gets in the
way of a single zImage. Moving to the common sched_clock framework
makes the code slightly cleaner.
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On ARM, we don't want SPARSE_IRQ to be a user visible option. Make
SPARSE_IRQ visible based on MAY_HAVE_SPARSE_IRQ instead of depending
on HAVE_SPARSE_IRQ.
With this, SPARSE_IRQ is not visible on C6X and ARM.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-c6x-dev@linux-c6x.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-sh@vger.kernel.org
To ensure correct alignment of cacheline-aligned data, the maximum
cacheline size needs to be known at compile time.
Since Cortex-A8 and Cortex-A15 have 64-byte cachelines (and it is likely
that there will be future ARMv7 implementations with the same line size)
then it makes sense to assume that CPU_V7 implies a 64-byte L1 cacheline
size. For CPUs with smaller caches, this will result in some harmless
padding but will help with single zImage work and avoid hitting subtle
bugs with misaligned data structures.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many architectures don't want to pull in iomap.c,
so they ended up duplicating pci_iomap from that file.
That function isn't trivial, and we are going to modify it
https://lkml.org/lkml/2011/11/14/183
so the duplication hurts.
This reduces the scope of the problem significantly,
by moving pci_iomap to a separate file and
referencing that from all architectures.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPBZXBAAoJECgfDbjSjVRpuuYIAIMD0wE96MuTOSBJX4VG8VAP
UyjL9dsfMRy8CKioQo5/fxpTY07YBCWmNauSSX7pzgcoUKBfYIGn4Z1qwGYsWK9M
CzLs6PXLTugw0FtKobHZl/klRTWEBS6YOUjp9x568rplwF+Ppk7b993uj7eS/g+e
T0mUKzqg4/UavbHd9+W5KgC4drQ5hgtu2WZHoUxBK4umnd3C2G+U82Sthg50o/XU
SC8IGm39K8I36HoIWgXj3Y7nkOP3mQELohOT4ZPiVSmLvGS4i47+ix75anO+8ZvZ
jxHr8RC85IK1Nd89NZhbKOyvx0QQiwoKUZaTwcWXJNSOADzZnM6icdIsodc+Elo=
=ccQZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
lib: use generic pci_iomap on all architectures
Many architectures don't want to pull in iomap.c,
so they ended up duplicating pci_iomap from that file.
That function isn't trivial, and we are going to modify it
https://lkml.org/lkml/2011/11/14/183
so the duplication hurts.
This reduces the scope of the problem significantly,
by moving pci_iomap to a separate file and
referencing that from all architectures.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
alpha: drop pci_iomap/pci_iounmap from pci-noop.c
mn10300: switch to GENERIC_PCI_IOMAP
mn10300: add missing __iomap markers
frv: switch to GENERIC_PCI_IOMAP
tile: switch to GENERIC_PCI_IOMAP
tile: don't panic on iomap
sparc: switch to GENERIC_PCI_IOMAP
sh: switch to GENERIC_PCI_IOMAP
powerpc: switch to GENERIC_PCI_IOMAP
parisc: switch to GENERIC_PCI_IOMAP
mips: switch to GENERIC_PCI_IOMAP
microblaze: switch to GENERIC_PCI_IOMAP
arm: switch to GENERIC_PCI_IOMAP
alpha: switch to GENERIC_PCI_IOMAP
lib: add GENERIC_PCI_IOMAP
lib: move GENERIC_IOMAP to lib/Kconfig
Fix up trivial conflicts due to changes nearby in arch/{m68k,score}/Kconfig
Randomization of PIE load address is hard coded in binfmt_elf.c for X86
and ARM. Create a new Kconfig variable
(CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE) for this and use it instead. Thus
architecture specific policy is pushed out of the generic binfmt_elf.c and
into the architecture Kconfig files.
X86 and ARM Kconfigs are modified to select the new variable so there is
no change in behavior. A follow on patch will select it for MIPS too.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Another simple series related to clock management, this time only for
imx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=czKE
-----END PGP SIGNATURE-----
Merge tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
clock management changes for i.MX
Another simple series related to clock management, this time only for
imx.
* tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mxs: select HAVE_CLK_PREPARE for clock
clk: add config option HAVE_CLK_PREPARE into Kconfig
ASoC: mxs-saif: convert to clk_prepare/clk_unprepare
video: mxsfb: convert to clk_prepare/clk_unprepare
serial: mxs-auart: convert to clk_prepare/clk_unprepare
net: flexcan: convert to clk_prepare/clk_unprepare
mtd: gpmi-lib: convert to clk_prepare/clk_unprepare
mmc: mxs-mmc: convert to clk_prepare/clk_unprepare
dma: mxs-dma: convert to clk_prepare/clk_unprepare
net: fec: add clk_prepare/clk_unprepare
ARM: mxs: convert platform code to clk_prepare/clk_unprepare
clk: add helper functions clk_prepare_enable and clk_disable_unprepare
Fix up trivial conflicts in drivers/net/ethernet/freescale/fec.c due to
commit 0ebafefcaa ("net: fec: add clk_prepare/clk_unprepare") clashing
trivially with commit e163cc97f9 ("net/fec: fix the .remove code").
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIVAwUATwtZUmCrR//JCVInAQL93hAAzBbSkswA4SD09UXHPSLGpbWd7JYuax9T
sR17FvnQCV+0T8c7ORRbjoBrCrxKkxuPMkFrfIHuTaP+beYe13CwTf2mV+dtnuv2
hSjSjdgCq+yv+CvRZhRnmHqmEePN1dvRoC9Q/EVPEibJNJ4BjrTALMfkXbsTz861
BOmcD7VGi0YfPhwRQ3D00MjohCflRoV2EmceHCUvH4HLEgpWcWl16UZeuWGn6BiA
GJK37O2ubKz0hkExAH6NHEaRxeFsapjh8kkR8/dOoNh/iIlmmR5SRPOxMPWFD0ui
lUeSc6QjMipHCzkfE7jUx6MICDZfRx+WRWVTwa/OTLJjJtY+zcRnUvoLl84XJqgX
EG5YhyL+Os4Z0ci92uSK3rwYQ2AJz/r4dS6VWnAVVJHSc8zHCuioJL4KcF81llcz
1dshlHkB1H1EeVrf08OM/1xX0X7SNzVJlQ801OZj31DYYtMqvrev72vn+tvJh6kL
o9gZsOSl3cIlFi8cAK0WmZmwGHw4wfUDZb1ojN6GDctdrp/Vmwe3exHleWvfSDtN
QBw4WyHl46JGw4bFVQ4hRH3vJZNuiso+ZNZvG3qGaEMfpNY5aMTy7lrxI/GFbFkA
tEnhkDgjutEZ/B6nEF1h8cCrcLND7u4n209kJh6UR1Qx3a6xD/M/ycE4tisNuPE3
wSSYuM1ZGTU=
=vPhu
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Driver specific changes
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq()
pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq()
ARM: EXYNOS: Modified files for SPI consolidation work
ARM: S5P64X0: Enable SDHCI support
ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names
ARM: S5P64X0: Add HSMMC setup for host Controller
ARM: EXYNOS: Add USB OHCI support to ORIGEN board
USB: Add Samsung Exynos OHCI diver
ARM: EXYNOS: Add USB OHCI support to SMDKV310 board
ARM: EXYNOS: Add USB OHCI device
net: macb: fix build break with !CONFIG_OF
i2c: tegra: Support DVC controller in device tree
i2c: tegra: Add __devinit/exit to probe/remove
net/at91_ether: use gpio_is_valid for phy IRQ line
ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT
...
Cleanup patches for various ARM platforms and some of their associated
drivers, the bulk of these is for mach-91.
I ended up pulling in the restart branch from Russell in order to
fix up some simple but annoying merge conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9q+1
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Cleanups on various subarchitectures
Cleanup patches for various ARM platforms and some of their associated
drivers, the bulk of these is for mach-91.
Arnd ended up pulling in the restart branch from Russell in order to
fix up some simple but annoying merge conflicts.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
arm/at91: fix build of stamp9g20
ARM: u300: delete memory.h
MAINTAINERS: add maintainer entry for Picochip picoxcell
ARM: picoxcell: move io mappings to common.c
ARM: picoxcell: don't reserve irq_descs
ARM: picoxcell: remove mach/memory.h
ARM: at91: delete the pcontrol_g20_defconfig
arm/tegra: Remove code that's ifndef CONFIG_ARM_GIC
arm/tegra: remove unused defines
arm/tegra: fix variable formatting in makefile
ARM: davinci: vpif: move code to driver core header from platform
ARM: at91/gpio: fix display of number of irq setuped
ARM: at91/gpio: drop PIN_BASE
ARM: at91/udc: use gpio_is_valid to check the gpio
ARM: at91/ohci: use gpio_is_valid to check the gpio
ARM: at91/nand: use gpio_is_valid to check the gpio
ARM: at91/mmc: use gpio_is_valid to check the gpio
ARM: at91/ide: use gpio_is_valid to check the gpio
ARM: at91/pata: use gpio_is_valid to check the gpio
ARM: at91/soc: use gpio_is_valid to check the gpio
...
Conflicts:
arch/arm/mach-mxs/include/mach/common.h
Pull in previous samsung conflict merges and do a trivial
merge of an mxs double-add conflict.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
Conflicts:
arch/arm/mach-exynos/common.c
The common.c file gets changes from rmk/stable-devel (part of
next/cleanup), rmk/restart, samsung/dt and follow-on branches
from the samsung tree.
Pulling it all together here hopefully avoids having to do
even more conflicting merge changesets in this one file. What
a mess!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-at91/at91cap9.c
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-at91/at91sam9rl.c
arch/arm/mach-exynos/cpu.c
arch/arm/mach-shmobile/board-kota2.c
This resolves a bunch of conflicts between the arm-soc tree
and changes from the arm tree that have gone upstream.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Telechips subarchitecture is being completely removed.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Harry Sievers <hsievers@csselectronic.com>
Signed-off-by: Hans J. Koch <hjk@hansjkoch.de>
This patch adds clk_prepare/clk_unprepare for mxs clock api by
renaming the existing non-atomic clk_enable/clk_disable to
clk_prepare/clk_unprepare and adding a pair of dummy
clk_enable/clk_disable. Then with selecting HAVE_CLK_PREPARE for
mxs clock, we can fix the mutex locking warning that has been
reported for a few times.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* drivers/rtc-sa1100:
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Conflicts:
arch/arm/mach-pxa/pxa25x.c
arch/arm/mach-pxa/pxa27x.c
Add default value for CONFIG_ARCH_NR_GPIO to Kconfig and remove the
definition in gpio.h. We can't remove gpio.h yet as asm/gpio.h still
includes it.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add default value for CONFIG_ARCH_NR_GPIO to Kconfig and remove the
definition in gpio.h.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change ARCH_NR_GPIO into a Kconfig variable as suggested by Russel King.
This makes ARCH_NR_GPIO single zImage friendly. The default value for
tegra is defined as well.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Activation conditions for a workaround should not be encoded in the
workaround's direct dependencies if this makes otherwise reasonable
configuration choices impossible.
This patches uses the SMP/UP patching facilities instead to compile
out the workaround if the configuration means that it is definitely
not needed.
This means that configs for buggy silicon can simply select
ARM_ERRATA_751472, without preventing a UP kernel from being built
or duplicatiing knowledge about when to activate the workaround.
This seems the correct way to do things, because the erratum is a
property of the silicon, irrespective of what the kernel config
happens to be.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Activation conditions for a workaround should not be encoded in the
workaround's direct dependencies if this makes otherwise reasonable
configuration choices impossible.
The workaround for erratum 720789 only affects a code path which is
not active in UP kernels; hence it should be safe to turn on in UP
kernels, without penalty.
This patch simply removes the extra dependency on SMP from Kconfig.
This means that configs for buggy silicon can simply select
ARM_ERRATA_720789, without preventing a UP kernel from being built
or duplicatiing knowledge about when to activate the workaround.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If running in the Normal World on a TrustZone-enabled SoC, Linux
does not have complete control over the L2 cache controller
configuration. The kernel cannot work reliably on such platforms
without the l2x0 cache support code built in.
This patch unconditionally enables l2x0 support for the Highbank
SoC.
Thanks to Rob Herring for this suggestion. [1]
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2011-November/074495.html
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Making SMP depend on (huge list of MACH_ and ARCH_ configs) is
bothersome to maintain and likely to lead to merge conflicts.
This patch moves the knowledge of which platforms are SMP-capable
to the individual machines. To enable this, a new HAVE_SMP config
option is introduced to allow machines to indicate that they can
run in a SMP configuration.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
(for nomadik, ux500)
Acked-by: Tony Lindgren <tony@atomide.com>
(for omap)
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
(for exynos)
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
(for imx)
Acked-by: Olof Johansson <olof@lixom.net>
(for tegra)
Making CACHE_L2X0 depend on (huge list of MACH_ and ARCH_ configs)
is bothersome to maintain and likely to lead to merge conflicts.
This patch moves the knowledge of which platforms have a L2x0 or
PL310 cache controller to the individual machines. To enable this,
a new MIGHT_HAVE_CACHE_L2X0 config option is introduced to allow
machines to indicate that they may have such a cache controller
independently of each other.
Boards/SoCs which cannot reliably operate without the L2 cache
controller support will need to select CACHE_L2X0 directly from
their own Kconfigs instead. This applies to some TrustZone-enabled
boards where Linux runs in the Normal World, for example.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
(for cns3xxx)
Acked-by: Tony Lindgren <tony@atomide.com>
(for omap)
Acked-by: Shawn Guo <shawn.guo@linaro.org>
(for imx)
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
(for exynos)
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
(for imx)
Acked-by: Olof Johansson <olof@lixom.net>
(for tegra)
Last merge window the memory maps for U300 were simplified so
we can now safely delete memory.h.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All irq_desc's are now dynamically allocated so we don't need to
statically reserve them.
v2: - select SPARSE_IRQ and set .nr_irqs to NR_IRQS_LEGACY to skip
ISA and IRQ 0.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Some Integrator core modules have TCM memory, so let's turn it on
if it's there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the sizing of NR_BANKS to a Kconfig control instead of selecting
it in a header file depending on platform selection. This allows new
additions to its dependencies to be handled more gracefully.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sending IPI_CPU_STOP to a CPU causes it to execute a busy cpu_relax
loop forever. This makes it impossible to kexec successfully on an SMP
system since the secondary CPUs do not reset.
This patch adds a callback to platform_cpu_kill, defined when
CONFIG_HOTPLUG_CPU=y, from the ipi_cpu_stop handling code. This function
currently just returns 1 on all platforms that define it but allows them
to do something more sophisticated in the future.
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds the ARM_LPAE and ARCH_PHYS_ADDR_T_64BIT Kconfig entries
allowing LPAE support to be compiled into the kernel.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit 1b9f95f8ad (ARM: prepare for removal of a bunch of <mach/memory.h>
files) introduced CONFIG_PHYS_OFFSET but the Kconfig hex prompt did not
provide a default value.
This has the undesired side effect of breaking a reportedly used
trick for updating defconfigs on the fly for routine buildtesting
across all arch and all platforms, i.e.
cp /path/to/somedefconfig .config ; yes "" | make oldconfig
because the config system will endlessly loop until a valid address is
provided.
However we can't just pick a random default value since it is likely to
be wrong for the majority of the boards as the right answer for this
option is quite varied. So the fact that the config system insists on
having a proper value be entered is actually a good thing.
It turns out that only at91x40_defconfig has this problem because it has
CONFIG_MMU=n. However, in the !MMU case, there is already a CONFIG_DRAM_BASE
value that can be used here. So let's use that as a default in that case
and suppress the redundant CONFIG_PHYS_OFFSET prompt.
Eventually the DRAM_BASE config option could simply be replaced by
PHYS_OFFSET directly, but that's a larger change better suited for later.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arm copied pci_iomap from generic code, probably to avoid
pulling the rest of iomap.c in. Since that's in
a separate file now, we can reuse the common implementation.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The Kconfig options for the PL310 errata workarounds do not use a
consistent naming scheme for either the config option or the bool
description.
This patch tidies up the options by ensuring that the bool descriptions
are prefixed with "PL310 errata:" and the config options are prefixed
with PL310_ERRATA_, making it much clearer in menuconfig as to what the
workarounds are for.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch implements a workaround for PL310 erratum 769419. On
revisions of the PL310 prior to r3p2, the Store Buffer does not
automatically drain. This can cause normal, non-cacheable writes to be
retained when the memory system is idle, leading to suboptimal I/O
performance for drivers using coherent DMA.
This patch adds an optional wmb() call to the cpu_idle loop. On systems
with an outer cache, this causes an explicit flush of the store buffer.
Cc: stable@vger.kernel.org
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The arch/arm/mach-exynos4 directory (CONFIG_ARCH_EXYNOS4) has
made for plaforms based on EXYNOS4 SoCs. But since upcoming
Samsung's SoCs such as EXYNOS5 (ARM Cortex A15) can reuse most
codes in current mach-exynos4, one mach-exynos directory will
be used for them.
This patch changes to CONFIG_ARCH_EXYNOS (arch/arm/mach-exynos)
but keeps original CONFIG_ARCH_EXYNOS4 in mach-exynos/Kconfig to
avoid changing in driver side.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'next/devel2' of git://git.linaro.org/people/arnd/arm-soc: (30 commits)
ARM: mmp: register internal sram bank
ARM: mmp: register audio sram bank
ARM: mmp: add sram allocator
gpio/samsung: Complain loudly if we don't know the SoC
ARM: S3C64XX: Fix SoC identification for S3C64xx devices
ARM: S3C2443: Remove redundant s3c_register_clocks call for init_clocks
ARM: S3C24XX: Add devname for hsmmc1 pclk
ARM: S3C24XX: use clk_get_rate to init fclk in common_setup_clocks
ARM: S3C2443: Accommodate cpufreq frequency scheme in armdiv
ARM: S3C2443: handle unset armdiv values gracefully
ARM: S3C2443: Add get_rate operation for clk_armdiv
ARM: S3C2416: Add comment describing the armdiv/armclk
ARM: S3C2443: Move clk_arm and clk_armdiv to common code
ARM: S3C24XX: Add infrastructure to transmit armdiv to common code
ARM: S3C2416: Add armdiv_mask constant
ARM: EXYNOS4: Add support for M-5MOLS camera on Nuri board
ARM: EXYNOS4: Enable MFC on ORIGEN
ARM: SAMSUNG: Add support s3c2416-adc for S3C2416/S3C2450
ARM: SAMSUNG: Add support s3c2443-adc for S3C2443
ARM: SAMSUNG: Allow overriding of adc device name for S3C24XX
...
* 'next/cleanup3' of git://git.linaro.org/people/arnd/arm-soc: (79 commits)
ARM: SAMSUNG: Move fimc plat. device from board files to plat-samsung
ARM: SAMSUNG: Cleanup resources by using macro
ARM: SAMSUNG: Cleanup plat-samsung/devs.c and devs.h
ARM: S5P: To merge devs.c files to one devs.c
ARM: S3C64XX: To merge devs.c files to one devs.c
ARM: S3C24XX: To merge s3c24xx devs.c files to one devs.c
ARM: S5P64X0: Add Power Management support
ARM: S5P: Make the sleep code common for S5P series SoCs
ARM: S5P: Make the common S5P PM code conditionally compile
ARM: SAMSUNG: Move S5P header files to plat-samsung
ARM: SAMSUNG: Move S3C24XX header files to plat-samsung
ARM: SAMSUNG: Moving each SoC support header files
ARM: SAMSUNG: Consolidate plat/pll.h
ARM: SAMSUNG: Consolidate plat/pwm-clock.h
ARM: SAMSUNG: Cleanup mach/clkdev.h
ARM: SAMSUNG: remove sdhci default configuration setup platform helper
ARM: EXYNOS4: Add FIMC device on SMDKV310 board
ARM: EXYNOS4: Add header file protection macros
ARM: EXYNOS4: Add usb ehci device to the SMDKV310
ARM: S3C2443: Add hsspi-clock from pclk and rename S3C2443 hsspi sclk
...
Fix up conflicts in
- arch/arm/mach-exynos4/{Kconfig,clock.c}
ARM_CPU_SUSPEND, various random device tables (gah!)
- drivers/gpio/Makefile
sa1100 gpio added, samsung gpio drivers merged
* 'next/soc' of git://git.linaro.org/people/arnd/arm-soc: (21 commits)
MAINTAINERS: add ARM/FREESCALE IMX6 entry
arm/imx: merge i.MX3 and i.MX6
arm/imx6q: add suspend/resume support
arm/imx6q: add device tree machine support
arm/imx6q: add smp and cpu hotplug support
arm/imx6q: add core drivers clock, gpc, mmdc and src
arm/imx: add gic_handle_irq function
arm/imx6q: add core definitions and low-level debug uart
arm/imx6q: add device tree source
ARM: highbank: add suspend support
ARM: highbank: Add cpu hotplug support
ARM: highbank: add SMP support
MAINTAINERS: add Calxeda Highbank ARM platform
ARM: add Highbank core platform support
ARM: highbank: add devicetree source
ARM: l2x0: add empty l2x0_of_init
picoxcell: add a definition of VMALLOC_END
picoxcell: remove custom ioremap implementation
picoxcell: add the DTS for the PC7302 board
picoxcell: add the DTS for pc3x2 and pc3x3 devices
...
Fix up trivial conflicts in arch/arm/Kconfig, and some more header file
conflicts in arch/arm/mach-omap2/board-generic.c (as per an ealier merge
by Arnd).
* 'next/devel' of git://git.linaro.org/people/arnd/arm-soc: (50 commits)
ARM: tegra: update defconfig
arm/tegra: Harmony: Configure PMC for low-level interrupts
arm/tegra: device tree support for ventana board
arm/tegra: add support for ventana pinmuxing
arm/tegra: prepare Seaboard pinmux code for derived boards
arm/tegra: pinmux: ioremap registers
gpio/tegra: Convert to a platform device
arm/tegra: Convert pinmux driver to a platform device
arm/dt: Tegra: Add pinmux node to tegra20.dtsi
arm/tegra: Prep boards for gpio/pinmux conversion to pdevs
ARM: mx5: fix clock usage for suspend
ARM i.MX entry-macro.S: remove now unused code
ARM i.MX boards: use CONFIG_MULTI_IRQ_HANDLER
ARM i.MX tzic: add handle_irq function
ARM i.MX avic: add handle_irq function
ARM: mx25: Add the missing IIM base definition
ARM i.MX avic: convert to use generic irq chip
mx31moboard: Add poweroff support
ARM: mach-qong: Add watchdog support
ARM: davinci: AM18x: Add wl1271/wlan support
...
Fix up conflicts in:
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-mx5/devices-imx53.h
arch/arm/plat-mxc/include/mach/memory.h
* 'next/deletion' of git://git.linaro.org/people/arnd/arm-soc:
ARM: mach-nuc93x: delete
Fix up trivial delete/edit conflicts in
arch/arm/mach-nuc93x/{Makefile.boot,mach-nuc932evb.c,time.c}
* 'next/fixes' of git://git.linaro.org/people/arnd/arm-soc: (28 commits)
ARM: pxa/cm-x300: properly set bt_reset pin
ARM: mmp: rename SHEEVAD to GPLUGD
ARM: imx: Fix typo 'MACH_MX31_3DS_MXC_NAND_USE_BBT'
ARM: i.MX28: shift frac value in _CLK_SET_RATE
plat-mxc: iomux-v3.h: implicitly enable pull-up/down when that's desired
ARM: mx5: fix clock usage for suspend
ARM: pxa: use correct __iomem annotations
ARM: pxa: sharpsl pm needs SPI
ARM: pxa: centro and treo680 need palm27x
ARM: pxa: make pxafb_smart_*() empty when not enabled
ARM: pxa: select POWER_SUPPLY on raumfeld
ARM: pxa: pxa95x is incompatible with earlier pxa
ARM: pxa: CPU_FREQ_TABLE is needed for CPU_FREQ
ARM: pxa: pxa95x/saarb depends on pxa3xx code
ARM: pxa: allow selecting just one of TREO680/CENTRO
ARM: pxa: export symbols from pxa3xx-ulpi
ARM: pxa: make zylonite_pxa*_init declaration match code
ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer available
ARM: at91: add defconfig for at91sam9g45 family
ARM: at91: remove dependency for Atmel PWM driver selector in Kconfig
...
The board changes in the imx/devel branch conflict with other changes in
the device imx/dt branch.
Conflicts:
arch/arm/mach-mx5/board-mx53_loco.c
arch/arm/mach-mx5/board-mx53_smd.c
arch/arm/plat-mxc/include/mach/common.h
arch/arm/plat-mxc/include/mach/memory.h
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are lots of conflicts between the omap and exynos cleanups
and the memory.h remove series.
Conflicts:
arch/arm/mach-exynos4/mach-smdkc210.c
arch/arm/mach-exynos4/mach-smdkv310.c
arch/arm/mach-imx/mach-cpuimx27.c
arch/arm/mach-omap1/board-ams-delta.c
arch/arm/mach-omap1/board-generic.c
arch/arm/mach-omap1/board-h2.c
arch/arm/mach-omap1/board-h3.c
arch/arm/mach-omap1/board-nokia770.c
arch/arm/mach-omap1/board-osk.c
arch/arm/mach-omap1/board-palmte.c
arch/arm/mach-omap1/board-palmtt.c
arch/arm/mach-omap1/board-palmz71.c
arch/arm/mach-omap1/board-sx1.c
arch/arm/mach-omap1/board-voiceblue.c
arch/arm/mach-omap1/io.c
arch/arm/mach-omap2/board-generic.c
arch/arm/mach-omap2/io.c
arch/arm/plat-omap/io.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This enables SMP support on highbank processor.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
This adds basic support for the Calxeda Highbank platform.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
These comments mention CONFIG options that do not exist: not as a symbol
in a Kconfig file (without the CONFIG_ prefix) and neither as a symbol
(with that prefix) in the code.
There's one reference to XSCALE_PMU_TIMER as a negative dependency.
But XSCALE_PMU_TIMER is never defined (CONFIG_XSCALE_PMU_TIMER is
also unused in the code). It shows up with type "unknown" if you search
for it in menuconfig. Apparently a negative dependency on an unknown
symbol is always true. That negative dependency can be removed too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
time, s390: Get rid of compile warning
dw_apb_timer: constify clocksource name
time: Cleanup old CONFIG_GENERIC_TIME references that snuck in
time: Change jiffies_to_clock_t() argument type to unsigned long
alarmtimers: Fix error handling
clocksource: Make watchdog reset lockless
posix-cpu-timers: Cure SMP accounting oddities
s390: Use direct ktime path for s390 clockevent device
clockevents: Add direct ktime programming function
clockevents: Make minimum delay adjustments configurable
nohz: Remove "Switched to NOHz mode" debugging messages
proc: Consider NO_HZ when printing idle and iowait times
nohz: Make idle/iowait counter update conditional
nohz: Fix update_ts_time_stat idle accounting
cputime: Clean up cputime_to_usecs and usecs_to_cputime macros
alarmtimers: Rework RTC device selection using class interface
alarmtimers: Add try_to_cancel functionality
alarmtimers: Add more refined alarm state tracking
alarmtimers: Remove period from alarm structure
alarmtimers: Remove interval cap limit hack
...
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (79 commits)
TTY: serial_core: Fix crash if DCD drop during suspend
tty/serial: atmel_serial: bootconsole removed from auto-enumerates
Revert "TTY: call tty_driver_lookup_tty unconditionally"
tty/serial: atmel_serial: add device tree support
tty/serial: atmel_serial: auto-enumerate ports
tty/serial: atmel_serial: whitespace and braces modifications
tty/serial: atmel_serial: change platform_data variable name
tty/serial: RS485 bindings for device tree
TTY: call tty_driver_lookup_tty unconditionally
TTY: pty, release tty in all ptmx_open fail paths
TTY: make tty_add_file non-failing
TTY: drop driver reference in tty_open fail path
8250_pci: Fix kernel panic when pch_uart is disabled
h8300: drivers/serial/Kconfig was moved
parport_pc: release IO region properly if unsupported ITE887x card is found
tty: Support compat_ioctl get/set termios_locked
hvc_console: display printk messages on console.
TTY: snyclinkmp: forever loop in tx_load_dma_buffer()
tty/n_gsm: avoid fifo overflow in gsm_dlci_data_output
tty/n_gsm: fix a bug in gsm_dlci_data_output (adaption = 2 case)
...
Fix up Conflicts in:
- drivers/tty/serial/8250_pci.c
Trivial conflict with removed duplicate device ID
- drivers/tty/serial/atmel_serial.c
Annoying silly conflict between "specify the port num via
platform_data" and other changes to atmel_console_init
On mmp platform, there have two sram banks:
audio sram and internal sram. The audio sram is mainly for audio;
the internal sram is for video, wtm and power management.
So add the sram allocator using genalloc to manage them.
Every sram bank will register its own platform device
info, after the sram allocator create the generic pool
for the sram bank, the user module can use the pool's
name to get the pool handler; then it can use the handler
to alloc/free memory with genalloc APIs.
Signed-off-by: Leo Yan <leoy@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
ARM uses its own BUG() handler which makes its output slightly different
from other archtectures.
One of the problems is that the ARM implementation doesn't report the function
with the BUG() in it, but always reports the PC being in __bug(). The generic
implementation doesn't have this problem.
Currently we get something like:
kernel BUG at fs/proc/breakme.c:35!
Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
PC is at __bug+0x20/0x2c
With this patch it displays:
kernel BUG at fs/proc/breakme.c:35!
Internal error: Oops - undefined instruction: 0 [#1] PREEMPT SMP
...
PC is at write_breakme+0xd0/0x1b4
This implementation uses an undefined instruction to implement BUG, and sets up
a bug table containing the relevant information. Many versions of gcc do not
support %c properly for ARM (inserting a # when they shouldn't) so we work
around this using distasteful macro magic.
v1: Initial version to replace existing ARM BUG() implementation with something
more similar to other architectures.
v2: Add Thumb support, remove backtrace whitespace output changes. Change to
use macros instead of requiring the asm %d flag to work (thanks to
Dave Martin <dave.martin@linaro.org>)
v3: Remove old BUG() implementation in favor of this one.
Remove the Backtrace: message (will submit this separately).
Use ARM_EXIT_KEEP() so that some architectures can dump exit text at link time
thanks to Stephen Boyd <sboyd@codeaurora.org> (although since we always
define GENERIC_BUG this might be academic.)
Rebase to linux-2.6.git master.
v4: Allow BUGS in modules (these were not reported correctly in v3)
(thanks to Stephen Boyd <sboyd@codeaurora.org> for suggesting that.)
Remove __bug() as this is no longer needed.
v5: Add %progbits as the section flags.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The affinity between ARM processors is defined in the MPIDR register.
We can identify which processors are in the same cluster,
and which ones have performance interdependency. We can define the
cpu topology of ARM platform, that is then used by sched_mc and sched_smt.
The default state of sched_mc and sched_smt config is disable.
When enabled, the behavior of the scheduler can be modified with
sched_mc_power_savings and sched_smt_power_savings sysfs interfaces.
Changes since v4 :
* Remove unnecessary parentheses and blank lines
Changes since v3 :
* Update the format of printk message
* Remove blank line
Changes since v2 :
* Update the commit message and some comments
Changes since v1 :
* Update the commit message
* Add read_cpuid_mpidr in arch/arm/include/asm/cputype.h
* Modify header of arch/arm/kernel/topology.c
* Modify tests and manipulation of MPIDR's bitfields
* Modify the place and dependancy of the config
* Modify Noop functions
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Given that we want the default to not have any <mach/memory.h> and given
that there are now fewer cases where it is still provided than the cases
where it is not at this point, this makes sense to invert the logic and
just identify the exception cases.
The word "need" instead of "have" was chosen to construct the config
symbol so not to suggest that having a mach/memory.h file is actually
a feature that one should aim for.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
This also removes the mach/s3c2400 version which was probably never used
due to the fact that we have this line in arch/arm/Makefile:
machine-$(CONFIG_ARCH_S3C2410) := s3c2410 s3c2400 [...]
This is later used to construct the search path for:
The compiler would be looking into mach-s3c2410 and picking up this
version first. Any config that was actually expecting the mach-s3c2400
version was therefore producing a broken kernel binary. Not relying on
any of them anymore would fix that issue.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The S3C64xx CPUs have TCMs so enable the kernel support for it
on these systems.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The pxa specific cpufreq code is based on the cpu_freq_table
module, so we have to select that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Awhile back I removed all the CONFIG_GENERIC_TIME referecnes as
the last of the non-GENERIC_TIME arches were converted.
However, due to the functionality being important and around for
awhile, there apparently were some out of tree hardware enablement
patches that used it and have since been merged.
This patch removes the remaining instances of GENERIC_TIME.
Singed-off-by: John Stultz <john.stultz@linaro.org>
Support for IDE drivers should not be automatic, since most platforms
cannot actually support any IDE low-level drivers. This partly
reverts 2064c946e "ARM: always select HAVE_IDE" to set this symbol
only when either a PC-style bus (PCI, ISA, PCMCIA) is enabled or
a platform is used that is known to have an existing driver in
drivers/ide.
New platforms should not need this option and just use CONFIG_ATA
with drivers/ata/.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Support for the cpu_suspend functions is only built-in
when CONFIG_PM_SLEEP is enabled, but omap3/4, exynos4
and pxa always call cpu_suspend when CONFIG_PM is enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Thumb2 kernels cannot be built with frame pointers, but can use the
ARM_UNWIND feature for unwinding instead. This makes sure that all
features that rely on unwinding includeing CONFIG_LATENCYTOP and
FAULT_INJECTION_STACKTRACE_FILTER do not enable frame pointers
when the unwinder is already selected, and we always build with
the unwinder when we want a thumb2 kernel, to make sure we do not
get the frame pointers instead.
A different option would be to redefine the CONFIG_FRAME_POINTERS
option on ARM to mean builing with either frame pointers or
the unwinder, and then select which one to use based on the
CPU architecture or another user option. That would still allow
building thumb2 kernels without the unwinder but would also be
more confusing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The SMP implementation on ARM heavily depends on MMU-only code.
As long as nobody is interested in fixing this, let's disable the
SMP option when building for nommu.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
picoXcell is a family of femtocell devices with an ARM application
processor and picoArray DSP processor array.
This patch adds support for picoXcell boards to be booted using the
device tree registering the VIC's, UART's and timers.
v3: - fixup vic compatible string in binding
v2: - cleanup empty mach headers
- convert to of_platform_populate()
- simplify uncompress.h
- split vic node into 2 devices
- add missing __initconst attributes
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
When the CONFIG_NO_MACH_MEMORY_H symbol is selected by a particular
machine class, the machine specific memory.h include file is no longer
used and can be removed. In that case the equivalent information can
be obtained dynamically at runtime by enabling CONFIG_ARM_PATCH_PHYS_VIRT
or by specifying the physical memory address at kernel configuration time.
If/when all instances of mach/memory.h are removed then this symbol could
be removed.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
This architecture received only generic maintenance since December 2009
when it was originally submitted, and no actual additional support since
then. It has no defconfig entry either, meaning that it was never built
by the ARM KAutobuild. Incidentally it currently doesn't build either
when CONFIG_MACH_NUC932EVB is selected which is the only possible config
choice.
This is therefore dead code and should be removed. If someone wants to
revive this code, it could be retrieved from the Git repository, and
ideally be merged in mach-w90x900/ instead.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch implements a workaround for erratum 764369 affecting
Cortex-A9 MPCore with two or more processors (all current revisions).
Under certain timing circumstances, a data cache line maintenance
operation by MVA targeting an Inner Shareable memory region may fail to
proceed up to either the Point of Coherency or to the Point of
Unification of the system. This workaround adds a DSB instruction before
the relevant cache maintenance functions and sets a specific bit in the
diagnostic control register of the SCU.
Cc: <stable@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some old bootloaders can't be updated to a device tree capable one,
yet they provide ATAGs with memory configuration, the ramdisk address,
the kernel cmdline string, etc. To allow a device tree enabled
kernel to be used with such bootloaders, it is necessary to convert those
ATAGs into FDT properties and fold them into the DTB appended to zImage.
Currently the following ATAGs are converted:
ATAG_CMDLINE
ATAG_MEM
ATAG_INITRD2
If the corresponding information already exists in the appended DTB, it
is replaced, otherwise the required node is created to hold it.
The code looks for ATAGs at the location pointed by the value of r2 upon
entry into the zImage code. If no ATAGs are found there, an attempt at
finding ATAGs at the typical 0x100 offset from start of RAM is made.
Otherwise the DTB is left unchanged.
Thisstarted from an older patch from John Bonesio <bones@secretlab.ca>,
with contributions from David Brown <davidb@codeaurora.org>.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
This patch provides the ability to boot using a device tree that is appended
to the raw binary zImage (e.g. cat zImage <filename>.dtb > zImage_w_dtb).
Signed-off-by: John Bonesio <bones@secretlab.ca>
[nico: ported to latest zImage changes plus additional cleanups/improvements]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
This rewrites the U300 GPIO so as to use gpiolib and
struct gpio_chip instead of just generic GPIO, hiding
all the platform specifics and passing in GPIO chip
variant as platform data at runtime instead of the
compiletime kludges.
As a result <mach/gpio.h> is now empty for U300 and
using just defaults.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Debian kernel maintainers <debian-kernel@lists.debian.org>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With uart tx/rx/err interrupt handling moved into the driver for s3c64xx
and later SoC's, the uart interrupt handling in plaform code can be removed.
The uart device irq resources is reduced to one and the related unused
macros are removed.
Suggested-by: Grant Likely <grant.likely@secretlab.ca>
CC: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is a workaround for the 364296 ARM1136 r0p2 erratum (possible
cache data corruption with hit-under-miss enabled). It sets the
undocumented bit 31 in the auxiliary control register and the FI bit in
the control register, thus disabling hit-under-miss without putting the
processor into full low interrupt latency mode.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This code can be removed now that MSM targets no longer need the 16-bit
offsets for P2V.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enable virtual to physical translation patching by default in all
kernels. Hide the option behind EMBEDDED.
This can still be turned off if people desire, and they know what
they're doing, to shrink the size of the kernel to a minimum.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This has now been well tested, and several platforms are now selecting
this directly. It's time to drop its experimental status.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds irq_domain infrastructure for translating from
hardware irq numbers to linux irqs. This is particularly important
for architectures adding device tree support because the current
implementation (excluding PowerPC and SPARC) cannot handle
translation for more than a single interrupt controller. irq_domain
supports device tree translation for any number of interrupt
controllers.
This patch converts x86, Microblaze, ARM and MIPS to use irq_domain
for device tree irq translation. x86 is untested beyond compiling it,
irq_domain is enabled for MIPS and Microblaze, but the old behaviour is
preserved until the core code is modified to actually register an
irq_domain yet. On ARM it works and is required for much of the new
ARM device tree board support.
PowerPC has /not/ been converted to use this new infrastructure. It
is still missing some features before it can replace the virq
infrastructure already in powerpc (see documentation on
irq_domain_map/unmap for details). Followup patches will add the
missing pieces and migrate PowerPC to use irq_domain.
SPARC has its own method of managing interrupts from the device tree
and is unaffected by this change.
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: Consolidate the clkdev header files
ARM: set vga memory base at run-time
ARM: convert PCI defines to variables
ARM: pci: make pcibios_assign_all_busses use pci_has_flag
ARM: remove unnecessary mach/hardware.h includes
pci: move microblaze and powerpc pci flag functions into asm-generic
powerpc: rename ppc_pci_*_flags to pci_*_flags
Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
* 'next/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
MAINTAINERS: add maintainer of CSR SiRFprimaII machine
ARM: CSR: initializing L2 cache
ARM: CSR: mapping early DEBUG_LL uart
ARM: CSR: Adding CSR SiRFprimaII board support
OMAP4: clocks: Update the clock tree with 4460 clock nodes
OMAP4: PRCM: OMAP4460 specific PRM and CM register bitshifts
OMAP4: ID: add omap_has_feature for max freq supported
OMAP: ID: introduce chip detection for OMAP4460
ARM: Xilinx: merge board file into main platform code
ARM: Xilinx: Adding Xilinx board support
Fix up conflicts in arch/arm/mach-omap2/cm-regbits-44xx.h
* 'next/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (133 commits)
ARM: EXYNOS4: Change devname for FIMD clkdev
ARM: S3C64XX: Cleanup mach/regs-fb.h from mach-s3c64xx
ARM: S5PV210: Cleanup mach/regs-fb.h from mach-s5pv210
ARM: S5PC100: Cleanup mach/regs-fb.h from mach-s5pc100
ARM: S3C24XX: Use generic s3c_set_platdata for devices
ARM: S3C64XX: Use generic s3c_set_platdata for OneNAND
ARM: SAMSUNG: Use generic s3c_set_platdata for NAND
ARM: SAMSUNG: Use generic s3c_set_platdata for USB OHCI
ARM: SAMSUNG: Use generic s3c_set_platdata for HWMON
ARM: SAMSUNG: Use generic s3c_set_platdata for FB
ARM: SAMSUNG: Use generic s3c_set_platdata for TS
ARM: S3C64XX: Add PWM backlight support on SMDK6410
ARM: S5P64X0: Add PWM backlight support on SMDK6450
ARM: S5P64X0: Add PWM backlight support on SMDK6440
ARM: S5PC100: Add PWM backlight support on SMDKC100
ARM: S5PV210: Add PWM backlight support on SMDKV210
ARM: EXYNOS4: Add PWM backlight support on SMDKC210
ARM: EXYNOS4: Add PWM backlight support on SMDKV310
ARM: SAMSUNG: Create a common infrastructure for PWM backlight support
clocksource: convert 32-bit down counting clocksource on S5PV210/S5P64X0
...
Fix up trivial conflict in arch/arm/mach-imx/mach-scb9328.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] s5pv210: make needlessly global symbols static
[CPUFREQ] exynos4210: make needlessly global symbols static
[CPUFREQ] S3C6410: Add some lower frequencies for 800MHz base clock operation
[CPUFREQ] S5PV210: Add reboot notifier to prevent system hang
[CPUFREQ] S5PV210: Adjust udelay prior to voltage scaling down
[CPUFREQ] S5PV210: Lock a mutex while changing the cpu frequency
[CPUFREQ] S5PV210: Add pm_notifier to prevent system unstable
[CPUFREQ] S5PV210: Add arm/int voltage control support
[CPUFREQ] S5PV210: Add additional symantics for "relation" in cpufreq with pm
[CPUFREQ] S3C64xx: Notify transition complete as soon as frequency changed
[CPUFREQ] S3C6410: Support 800MHz operation in cpufreq
[CPUFREQ] s5pv210-cpufreq.c: Add missing clk_put
[CPUFREQ] Move compile for S3C64XX cpufreq to /drivers/cpufreq
[CPUFREQ] Remove some vi noise that escaped into the Makefile.
[CPUFREQ] Move ARM Samsung cpufreq drivers to drivers/cpufreq/
[CPUFREQ/S3C64xx] Move S3C64xx CPUfreq driver into drivers/cpufreq
[CPUFREQ] Handle CPUs with different capabilities in acpi-cpufreq
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits)
ARM: 7004/1: fix traps.h compile warnings
ARM: 6998/2: kernel: use proper memory barriers for bitops
ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM
ARM: Fix build errors caused by adding generic macros
ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU
ARM: CPU hotplug: pass in proper affinity mask on IRQ migration
ARM: GIC: avoid routing interrupts to offline CPUs
ARM: CPU hotplug: fix abuse of irqdesc->node
ARM: 6981/2: mmci: adjust calculation of f_min
ARM: 7000/1: LPAE: Use long long printk format for displaying the pud
ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state
ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence
ARM: ARM_DMA_ZONE_SIZE is no more
ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
...
Add support for MFC device to plat-s5p, mach-exynos4, mach-s5pv210:
- clock support
- memory mapping and reserving
- s5p_device_mfc platform device
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Convert the S5PV210/S5P64X0 32-bit down-counting clocksource to
the generic mmio clocksource infrastructure
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
[kgene.kim@samsung.com: removed changes of mach-exynos4/time.c]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Now most of ARM machines has the alsmot same __clk_get/put() macro
So place it at the arch/arm/include/asm/clkdev.h and remove the reduntant header files
But some machines don't have the same form as above. It can use the machince specific clkdev file by HAVE_MACH_CLKDEV config
Now there are only 3 caese.
1) define the clk structure with clkdev macro => Need to move clk structure to proper header file
arch/arm/mach-versatile/include/mach/clkdev.h
arch/arm/mach-realview/include/mach/clkdev.h
arch/arm/mach-vexpress/include/mach/clkdev.h
arch/arm/mach-integrator/include/mach/clkdev.h
2) export the __clk_get/put function at clock.c
arch/arm/mach-shmobile/include/mach/clkdev.h
3) demuxing the clk source
arch/arm/mach-u300/include/mach/clkdev.h
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This was introduced more than 3 years ago, and since then only generic
janitorial changes were made without further addition of actual support
for "real" devices. This is therefore a cost with no benefits to keep
in the tree. If someone wishes to revive this code, it is always
possible to retrieve it from the Git repository.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
CC: Ke Wei <kewei@marvell.com>
CC: Saeed Bishara <saeed@marvell.com>
CC: Lennert Buytenhek <buytenh@wantstofly.org>
On Tue, 28 Jun 2011, Ben Dooks wrote:
> On Tue, Jun 28, 2011 at 11:22:57PM +0200, Arnd Bergmann wrote:
>
> > On a related note, what about mach-s3c2400? It seems to be even more
> > incomplete.
>
> Probably the same fate awaits that. It is so old that there's little
> incentive to do anything with it.
So out it goes as well.
The PORT_S3C2400 definition in include/linux/serial_core.h is left there
to prevent a reuse of the same number for another port type.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The barriers implemented in arch/arm/mach-tegra/mach/barriers.h
are exactly the same as the default barriers implemented in
arch/arm/include/asm/system.h. Remove barriers.h from Tegra,
and don't select ARCH_HAS_BARRIERS.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
clocksource support. This achieves several things:
1. It means we get rid of all these helper functions which frankly should
never have been necessary.
2. It means omap_readl() inside these helper functions does not appear in
ftrace output.
Another plus is that we avoid the overhead of calculating the address to
read each time, but a minus is that we use readl() which has a barrier.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[tony@atomide.com: updated to use ioremap]
Signed-off-by: Tony Lindgren <tony@atomide.com>
SiRFprimaII is the latest generation application processor from CSR’s
Multifunction SoC product family. Designed around an ARM cortex A9 core,
high-speed memory bus, advanced 3D accelerator and full-HD multi-format
video decoder, SiRFprimaII is able to meet the needs of complicated
applications for modern multifunction devices that require heavy concurrent
applications and fluid user experience. Integrated with GPS baseband,
analog and PMU, this new platform is designed to provide a cost effective
solution for Automotive and Consumer markets.
This patch adds the basic support for this SoC and EVB board based on device
tree. It is following the ZYNQ of Xilinx in some degree.
Signed-off-by: Binghua Duan <Binghua.Duan@csr.com>
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Yuping Luo <Yuping.Luo@csr.com>
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Huayi Li <Huayi.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
CNS3XXX is based on MPCore, so select the right CPU option for it.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
The scu_power_mode function can be used on UP builds as it drives signals
to an SOC power controller. So make it selectable for !SMP.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the generic power domains support introduced by the previous
patch to implement support for power domains on SH7372.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
This allows a ROM-able zImage to be written to eSD and for SuperH Mobile
ARM to boot directly from the SDHI hardware block.
This is achieved by the MaskROM loading the first portion of the image into
MERAM and then jumping to it. This portion contains loader code which
copies the entire image to SDRAM and jumps to it. From there the zImage
boot code proceeds as normal, uncompressing the image into its final
location and then jumping to it.
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The 1st board support is minimal to get a system up and running
on the Xilinx platform.
This platform reuses the clock implementation from plat-versatile, and
it depends entirely on CONFIG_OF support. There is only one board
support file which obtains all device information from a device tree
dtb file which is passed to the kernel at boot time.
Signed-off-by: John Linn <john.linn@xilinx.com>
Allow SoCs to enable the scatterlist chaining support, which allows
scatterlist tables to be broken up into smaller allocations.
As support for this feature depends on the implementation details of
the users of the scatterlists, we can't enable this globally without
auditing all the users, which is a very big task. Instead, let SoCs
progressively switch over to using this.
SoC drivers using scatterlists and SoC DMA implementations need
auditing before this option can be enabled for the SoC.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hotplug support was added in 9f1890a (msm: hotplug: support cpu hotplug
on msm, 2010-12-02)
Signed-off-by: Jeff Ohlstein <johlstei@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In commit eb33575c ("[ARM] Double check memmap is actually valid with a
memmap has unexpected holes V2"), a new function, memmap_valid_within,
was introduced to mmzone.h so that holes in the memmap which pass
pfn_valid in SPARSEMEM configurations can be detected and avoided.
The fix to this problem checks that the pfn <-> page linkages are
correct by calculating the page for the pfn and then checking that
page_to_pfn on that page returns the original pfn. Unfortunately, in
SPARSEMEM configurations, this results in reading from the page flags to
determine the correct section. Since the memmap here has been freed,
junk is read from memory and the check is no longer robust.
In the best case, reading from /proc/pagetypeinfo will give you the
wrong answer. In the worst case, you get SEGVs, Kernel OOPses and hung
CPUs. Furthermore, ioremap implementations that use pfn_valid to
disallow the remapping of normal memory will break.
This patch allows architectures to provide their own pfn_valid function
instead of using the default implementation used by sparsemem. The
architecture-specific version is aware of the memmap state and will
return false when passed a pfn for a freed page within a valid section.
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
select ARM_PATCH_PHYS_VIRT
as with ARM_PATCH_PHYS_VIRT you can patch boot_params at runtime or any recent
bootloader will provide a valid atags pointer in r2
as point out by Russell on AT91 we never use XIP
so se do not need PLAT_PHYS_OFFSET
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
we do not change the clock naming convention so does not need to switch
the AVR32 yet
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
bcmring has a set of four sp804 timers incorporated, yet it has its
own copy of the sp804 code. Convert its clocksource implementation
to the standard sp804 support code.
Cc: Jiandong Zheng <jdzheng@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the MXS timrotv2 32-bit down counting clocksource to the
generic clocksource infrastructure.
Cc: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert SPEAr platforms 16-bit up counting clocksource, which requires
a 16-bit register access read rather than 32-bit.
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the W90x900 24-bit down-counting clocksource to the generic
mmio clocksource infrastructure
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert ixp4xx, lpc32xx, mxc, netx, pxa, sa1100, tcc8k, tegra and u300
to use the generic mmio clocksource recently introduced.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: "Hans J. Koch" <hjk@hansjkoch.de>
Acked-by: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Olof Johansson <olof@lixom.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As a result of c42321c (genirq: Make generic irq chip depend on
CONFIG_GENERIC_IRQ_CHIP), we now need those platforms using this in
my tree to select this symbol.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current mainline codes of ARCH_S5PC100 cannot support
suspend to ram. So needs this for preventing build error.
Cc: Russell King <rmk+kernel at arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim at samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch allows the provided CONFIG_CMDLINE to be concatenated
with the one provided by the boot loader. This is useful to
merge the static values defined in CONFIG_CMDLINE with the
boot loader's (possibly) more dynamic values, such as startup
reasons and more.
Signed-off-by: Victor Boivie <victor.boivie@sonyericsson.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonyericsson.com>
Signed-off-by: Oskar Andero <oskar.andero@sonyericsson.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Highmem on ARM has been around for a while now, without any major issues
being raised. So, drop the experimental status of this feature.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SMP on ARM has been around for a while now, without any major issues
being raised. So, drop the experimental status of this feature.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add some basic empty infrastructure for DT support on ARM.
v5: - Fix off-by-one error in size calculation of initrd
- Stop mucking with cmd_line, and load command line from dt into
boot_command_line instead which matches the behaviour of ATAGS booting
v3: - moved cmd_line export and initrd setup to this patch to make the
series bisectable.
- switched to alloc_bootmem_align() for allocation when
unflattening the device tree. memblock_alloc() was not the
right interface.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Disabled legacy support for ARMv6 architecture on Dove platform.
Latest Dove HW uses only ARMv7 model.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Now that both users of plat-stmp have been deleted in previous patches,
delete the platform, too.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The port is actually unmaintained and only received global
cleanups and a few build fixes since mid 2008.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The HIGHPTE config option depends on !OUTER_CACHE. However, there is no
set_pte_ext() function that does outer cache maintenance by physical
address, hence no need for such restriction.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Offering CONFIG_PM_SLEEP for CPUs which do not support suspend leads to
build errors, so only set CONFIG_ARCH_SUSPEND_POSSIBLE if we have a CPU
selected which supports suspend.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current mainline codes of ARCH_S5P64X0 and ARCH_S5P6442
can not support suspend to ram. So needs this for preventing
build error on them.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (35 commits)
ARM: Update (and cut down) mach-types
ARM: 6771/1: vexpress: add support for multiple core tiles
ARM: 6797/1: hw_breakpoint: Fix newlines in WARNings
ARM: 6751/1: vexpress: select applicable errata workarounds in Kconfig
ARM: 6753/1: omap4: Enable ARM local timers with OMAP4430 es1.0 exception
ARM: 6759/1: smp: Select local timers vs broadcast timer support runtime
ARM: pgtable: add pud-level code
ARM: 6673/1: LPAE: use phys_addr_t instead of unsigned long for start of membanks
ARM: Use long long format when printing meminfo physical addresses
ARM: integrator: add Integrator/CP sched_clock support
ARM: realview/vexpress: consolidate SMP bringup code
ARM: realview/vexpress: consolidate localtimer support
ARM: integrator/versatile: consolidate FPGA IRQ handling code
ARM: rationalize versatile family Kconfig/Makefile
ARM: realview: remove old AMBA device DMA definitions
ARM: versatile: remove old AMBA device DMA definitions
ARM: vexpress: use new init_early for clock tree and sched_clock init
ARM: realview: use new init_early for clock tree and sched_clock init
ARM: versatile: use new init_early for clock tree and sched_clock init
ARM: integrator: use new init_early for clock tree init
...
Add sched_clock using cyc_to_sched_clock and update_sched_clock
with HAVE_SCHED_CLOCK
tested on iMX27 and iMX35
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'for-linus' of git://codeaurora.org/quic/kernel/davidb/linux-msm: (46 commits)
msm: scm: Check for interruption immediately
msm: scm: Fix improper register assignment
msm: scm: Mark inline asm as volatile
msm: iommu: Enable HTW L2 redirection on MSM8960
msm: iommu: Don't read from write-only registers
msm: iommu: Remove dependency on IDR
msm: iommu: Use ASID tagging instead of VMID tagging
msm: iommu: Rework clock logic and add IOMMU bus clock control
msm: iommu: Clock control for the IOMMU driver
msm: mdp: Set the correct pack pattern for XRGB/ARGB
msm_fb: Fix framebuffer console
msm: mdp: Add support for RGBX 8888 image format.
video: msmfb: Put the partial update magic value into the fix_screen struct.
msm: clock: Migrate to clkdev
msm: clock: Remove references to clk_ops_pcom
msm: headsmp.S: Fix section mismatch
msm: Use explicit GPLv2 licenses
msm: iommu: Enable IOMMU support for MSM8960
msm: iommu: Generalize platform data for multiple targets
msm: iommu: Create a Kconfig item for the IOMMU driver
...
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
This patch updates s5pv210_defconfig and s5p64x0_defconfig for
HRT support and CONFIG_S5P_HRT is used for its configuration.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Multi-Core Timer(MCT) of EXYNOS4 is designed for implementing
clock source timer and clock event timers. This patch implements
1 clock source timer with 64 bit free running counter of MCT and
2 clock event timers with two of 31-bit tick counters.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Various binutils versions can resolve Thumb-2 branches to
locally-defined, preemptible global symbols as short-range "b.n"
branch instructions.
This is a problem, because there's no guarantee the final
destination of the symbol, or any candidate locations for a
trampoline, are within range of the branch. For this reason, the
kernel does not support fixing up the R_ARM_THM_JUMP11 (102)
relocation in modules at all, and it makes little sense to add
support.
The symptom is that the kernel fails with an "unsupported
relocation" error when loading some modules.
Until fixed tools are available, passing
-fno-optimize-sibling-calls to gcc should prevent gcc generating
code which hits this problem, at the cost of a bit of extra runtime
stack usage in some cases.
The problem is described in more detail at:
https://bugs.launchpad.net/binutils-linaro/+bug/725126
Only Thumb-2 kernels are affected.
This patch adds a new CONFIG_THUMB2_AVOID_R_ARM_THM_JUMP11 config
option which adds -fno-optimize-sibling-calls to CFLAGS_MODULE
when building a Thumb-2 kernel.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adding Thumb2 support to the runtime patching of the virt_to_phys and
phys_to_virt opcodes.
Tested both the 8-bit and the 16-bit fixups, using different placements
in memory to exercize all code paths.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On revisions of the Cortex-A9 prior to r2p0, the Store Buffer does not
have any automatic draining mechanism and therefore a livelock may occur
if an external agent continuously polls a memory location waiting to
observe an update.
This workaround defines cpu_relax() as smp_mb(), preventing correctly
written polling loops from denying visibility of updates to memory.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On the r2p* and r3p* versions of the Cortex-A9, a speculative memory
access may cause a page table walk which starts prior to an ASID switch
but completes afterwards. This can populate the micro-TLB with a stale
entry which may be hit with the new ASID.
This workaround places two dsb instructions in the mm switching code so
that no page table walks can cross the ASID switch.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use straight 64-bit values as 64-bit operations are fairly efficient on ARM.
Comparing the asm output with and without KTIME_SCALAR, using 64-bit math
generates clearly better code.
Comparing kernel/hrtimer.c .text size, it goes from 0x1414 to 0x119c with
this change.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PL310 implements the Clean & Invalidate by Way L2 cache maintenance
operation (offset 0x7FC). This operation runs in background so that
PL310 can handle normal accesses while it is in progress. Under very
rare circumstances, due to this erratum, write data can be lost when
PL310 treats a cacheable write transaction during a Clean & Invalidate
by Way operation.
Workaround:
Disable Write-Back and Cache Linefill (Debug Control Register)
Clean & Invalidate by Way (0x7FC)
Re-enable Write-Back and Cache Linefill (Debug Control Register)
This patch also removes any OMAP dependency on PL310 Errata's
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Migrating to clkdev has several advantages:
* Less code in mach-msm/clock.c
* A more robust clk_get() implementation
* clk_add_alias() support
* clk_get_sys() support
In general, this will help board authors setup clock aliases and
break the dependency on device pointers in the clock tables.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Move L1_CACHE_SHIFT related options together, rather than spreading them
across two separate Kconfig files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch changes the Kconfig and Makefile for the new ARCH_EXYNOS4.
It also updates arch/arm/Kconfig, Makeifile and arch/arm/mm/Kconfig
to include support for the new ARCH_EXYNOS4.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On versions of the Cortex-A9 prior to r3p0, an interrupted ICIALLUIS
operation may prevent the completion of a following broadcasted
operation if the second operation is received by a CPU before the
ICIALLUIS has completed, potentially leading to corrupted entries in
the cache or TLB.
This workaround sets a bit in the diagnostic register of the Cortex-A9,
causing CP15 maintenance operations to be uninterruptible.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The effect of cache sync operation is to drain the store buffer and
wait for all internal buffers to be empty. In normal conditions, store
buffer is able to merge the normal memory writes within its 32-byte
data buffers. Due to this erratum present in r3p0, the effect of cache
sync operation on the store buffer still remains when the operation
completes. This means that the store buffer is always asked to drain
and this prevents it from merging any further writes.
This can severely affect performance on the write traffic esp. on
Normal memory NC one.
The proposed workaround is to replace the normal offset of cache sync
operation(0x730) by another offset targeting an unmapped PL310
register 0x740.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidate the FPGA IRQ handling code. Integrator/AP and Versatile
have one FPGA-based IRQ handler each. Integrator/CP has three.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move leds and sched_clock build conditionals out of the Makefile into
the Kconfig file. Move selection of HAVE_SCHED_CLOCK into the
platform Kconfig rather than duplicating it three times in the main
architecture Kconfig.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This switches Versatile Express to use the conslidated CLCD panel
support, including the display capabilities. As Versatile Express uses
a PL111, it can support the full range of pixel formats - 444, 5551,
565 in both RGB and BGR mode.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This switches Realview platforms to use the consolidated CLCD panel
support, including the display capabilities. As Realview uses a PL111,
it can support the full range of pixel formats - 444, 5551, 565 in both
RGB and BGR mode.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This switches Versatile platforms to use the consolidated CLCD panel
support, including the display capabilities. Versatile can support
RGB5551, BGR5551, RGB565 and BGR565 modes.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This consolidates the CLCD panel definitions and memory allocation into
one location.
Rename the Sanyo 2.5in and Epson 2.2in displays after their respective
part numbers. Rather than using a general "Sanyo 2.5in" and "Epson
2.2in" description of the display panel, use the manufacturers part
number to be more specific. This helps people identify what the timings
actually refer to, which are panel specific.
While here, add CLCD capability information to each panel definition,
which has no effect until we add the board-level capabilities.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MSM's memory is aligned to 2MB, which is more than we can do with our
existing method as we're limited to the upper 8 bits. Extend this by
using two instructions to 16 bits, automatically selected when MSM is
enabled.
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This idea came from Nicolas, Eric Miao produced an initial version,
which was then rewritten into this.
Patch the physical to virtual translations at runtime. As we modify
the code, this makes it incompatible with XIP kernels, but allows us
to achieve this with minimal loss of performance.
As many translations are of the form:
physical = virtual + (PHYS_OFFSET - PAGE_OFFSET)
virtual = physical - (PHYS_OFFSET - PAGE_OFFSET)
we generate an 'add' instruction for __virt_to_phys(), and a 'sub'
instruction for __phys_to_virt(). We calculate at run time (PHYS_OFFSET
- PAGE_OFFSET) by comparing the address prior to MMU initialization with
where it should be once the MMU has been initialized, and place this
constant into the above add/sub instructions.
Once we have (PHYS_OFFSET - PAGE_OFFSET), we can calculate the real
PHYS_OFFSET as PAGE_OFFSET is a build-time constant, and save this for
the C-mode PHYS_OFFSET variable definition to use.
At present, we are unable to support Realview with Sparsemem enabled
as this uses a complex mapping function, and MSM as this requires a
constant which will not fit in our math instruction.
Add a module version magic string for this feature to prevent
incompatible modules being loaded.
Tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
rmk says: "You might as well make OABI_COMPAT depend on !THUMB2_KERNEL.
OABI userland is useless without FPA support."
nwfpe doesn't work with Thumb-2 anyway and will probably never get
ported, so I can't argue with that.
This patch implements the dependency change.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mach-aaec2000 is no longer actively maintained and is only receiving
fixups to remain building with other kernel updates.
Cc: Bellido Nicolas <ml@acolin.be>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SMP extensions are only supported on ARMv6k or ARMv7 architectures, so
only offer the option if we're building for such an architecture.
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If CONFIG_CPU_V6 is enabled, avoid using the double-word exclusive
instructions in the kernel's atomic implementations as these are not
supported. Fall back to the generic spinlock code instead.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make Dove platforms select the new V6K CPU option.
Tested-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce a CPU_V6K configuration option for platforms to select if they
have a V6K CPU core. This allows us to identify whether we need to
support ARMv6 CPUs without the V6K SMP extensions at build time.
Currently CPU_V6K is just an alias for CPU_V6, and all places which
reference CPU_V6 are replaced by (CPU_V6 || CPU_V6K).
Select CPU_V6K from platforms which are known to be V6K-only.
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Footbridge platforms have some reasonable timers in the host bridge,
which we use for most footbridge-based platforms. However, NetWinder's
clock these using a spread-spectrum clock which makes them too unstable
for time keeping. So we have to rely on the PIT.
Convert both Footbridge timers and PIT timers to use the clocksource
and clockevent infrastructure. Tested on Netwinder.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The compactflash device on this platform is not usable simply because it
is never registered with the kernel. Fix that up.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds support for the family of Systems-on-Chip produced initially
by VIA and now its subsidiary WonderMedia that have recently become
widespread in lower-end Chinese ARM-based tablets and netbooks.
Support is included for both VT8500 and WM8505, selectable by a
configuration switch at kernel build time.
Included are basic machine initialization files, register and
interrupt definitions, support for the on-chip interrupt controller,
high-precision OS timer, GPIO lines, necessary macros for early debug,
pulse-width-modulated outputs control, as well as platform device
configurations for the specific drivers implemented elsewhere.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows a ROM-able zImage to be written to MMC and
for SuperH Mobile ARM to boot directly from the MMCIF
hardware block.
This is achieved by the MaskROM loading the first portion
of the image into MERAM and then jumping to it. This portion
contains loader code which copies the entire image to SDRAM
and jumps to it. From there the zImage boot code proceeds
as normal, uncompressing the image into its final location
and then jumping to it.
Cc: Magnus Damm <magnus.damm@gmail.com>
Russell, please consider merging this for 2.6.38.
This patch depends on:
* "mmc, sh: Move MMCIF_PROGRESS_* into sh_mmcif.h"
which will be merged though Paul Mundt's rmobile sh-2.6.
The absence of this patch will break the build if
the (new) CONFIG_ZBOOT_ROM_MMCIF option is set.
There are no subtle side-effects.
v2:
Addressed comments by Magnus Damm
* Fix copyright in vrl4.c
* Fix use of #define CONFIG_ZBOOT_ROM_MMCIF in mmcif-sh7372.c
* Initialise LED GPIO lines in head-ap4evb.txt instead of mmcif-sh7372.c
as this is considered board-specific.
v3:
Addressed comments made in person by Magnus Damm
* Move mmcif_loader to be earlier in the image and
reduce the number of blocks of boot program loaded by the MaskRom
from 40 to 8 accordingly.
* Move LED GPIO initialisation into mmcif_progress_init
- This leaves the partner jet script unbloated
Other
* inline mmcif_update_progress so it is a static inline in a header file
v4:
* Use htole16() and htole32() in v4rl.c to ensure
that the output is little endian
v5:
Addressed comments by Russell King
* Simplify assembly code
* Jump to code rather than an address <- bug fix
* Use (void __iomem *) as appropriate
Roll in mackerel support
* This was previously a separate patch, only because of the order
in which this code was developed
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
lh7a40x has only been receiving updates for updates to generic code.
The last involvement from the maintainer according to the git logs was
in 2006. As such, it is a maintainence burden with no benefit.
This gets rid of two defconfigs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: fix missing branch in __error_a
ARM: fix /proc/$PID/stack on SMP
ARM: Fix build regression on SA11x0, PXA, and H720x targets
ARM: 6625/1: use memblock memory regions for "System RAM" I/O resources
ARM: fix wrongly patched constants
ARM: 6624/1: fix dependency for CONFIG_SMP_ON_UP
ARM: 6623/1: Thumb-2: Fix out-of-range offset for Thumb-2 in proc-v7.S
ARM: 6622/1: fix dma_unmap_sg() documentation
ARM: 6621/1: bitops: remove condition code clobber for CLZ
ARM: 6620/1: Change misleading warning when CONFIG_CMDLINE_FORCE is used
ARM: 6619/1: nommu: avoid mapping vectors page when !CONFIG_MMU
ARM: sched_clock: make minsec argument to clocks_calc_mult_shift() zero
ARM: sched_clock: allow init_sched_clock() to be called early
ARM: integrator: fix compile warning in cpu.c
ARM: 6616/1: Fix ep93xx-fb init/exit annotations
ARM: twd: fix display of twd frequency
ARM: udelay: prevent math rounding resulting in short udelays
Since commit
6d803ba (ARM: 6483/1: arm & sh: factorised duplicated clkdev.c)
platforms need to select CLKDEV_LOOKUP instead of COMMON_CLKDEV and need
to include <linux/clkdev.h>.
Cc: Shawn Guo <shawn.guo@freescale.com>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This depends on !XIP_KERNEL and not !XIP.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add ARM support for the DMA debug infrastructure, which allows the
DMA API usage to be debugged.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a sched_clock() implementation to Versatile Express using the new
sched_clock() infrastructure for extending 32bit counters to full
64-bit nanoseconds.
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow one shot timer mode to be used with the TWD. This allows
NOHZ mode to be used on SMP systems using the TWD localtimer.
Tested on Versatile Express and U8500.
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Normally different ARM platform has different way to decode the IRQ
hardware status and demultiplex to the corresponding IRQ handler.
This is highly optimized by macro irq_handler in entry-armv.S, and
each machine defines their own macro to decode the IRQ number.
However, this prevents multiple machine classes to be built into a
single kernel.
By allowing each machine to specify thier own handler, and making
function pointer 'handle_arch_irq' to point to it at run time, this
can be solved. And introduce CONFIG_MULTI_IRQ_HANDLER to allow both
solutions to work.
Comparing with the highly optimized macro of irq_handler, the new
function must be written with care not to lose too much performance.
And the IPI stuff on SMP is expected to move to the provided arch
IRQ handler as well.
The assembly code to invoke handle_arch_irq is optimized by Russell
King.
Signed-off-by: Eric Miao <eric.miao@canonical.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds ARCH_HAS_CPUFREQ in Kconfig of ARCH_S5PV310 and updates
Makefile for supporting build S5PV310 CPUFREQ driver.
Signed-off-by: Sunyoung Kang <sy0816.kang@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Convert versatile platforms to use the new sched_clock() infrastructure
for extending 32bit counters to full 64-bit nanoseconds.
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert orion platforms to use the new sched_clock() infrastructure for
extending 32bit counters to full 64-bit nanoseconds.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert omap to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert iop platforms to use the new sched_clock() infrastructure for
extending 32bit counters to full 64-bit nanoseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert u300 to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert tegra to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert sa1100 to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert pxa to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert mmp to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert ixp4xx to use the new sched_clock() infrastructure for
extending 32bit counters to full 64-bit nanoseconds.
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide common sched_clock() infrastructure for platforms to use to
create a 64-bit ns based sched_clock() implementation from a counter
running at a non-variable clock rate.
This implementation is based upon maintaining an epoch for the counter
and an epoch for the nanosecond time. When we desire a sched_clock()
time, we calculate the number of counter ticks since the last epoch
update, convert this to nanoseconds and add to the epoch nanoseconds.
We regularly refresh these epochs within the counter wrap interval.
We perform a similar calculation as above, and store the new epochs.
We read and write the epochs in such a way that sched_clock() can easily
(and locklessly) detect when an update is in progress, and repeat the
loading of these constants when they're known not to be stable. The
one caveat is that sched_clock() is not called in the middle of an
update. We achieve that by disabling IRQs.
Finally, if the clock rate is known at compile time, the counter to ns
conversion factors can be specified, allowing sched_clock() to be tightly
optimized. We ensure that these factors are correct by providing an
initialization function which performs a run-time check.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Olof Johansson <olof@lixom.net>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds nanoEngine's PCI support.
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* __fixup_smp_on_up has been modified with support for the
THUMB2_KERNEL case. For THUMB2_KERNEL only, fixups are split
into halfwords in case of misalignment, since we can't rely on
unaligned accesses working before turning the MMU on.
No attempt is made to optimise the aligned case, since the
number of fixups is typically small, and it seems best to keep
the code as simple as possible.
* Add a rotate in the fixup_smp code in order to support
CPU_BIG_ENDIAN, as suggested by Nicolas Pitre.
* Add an assembly-time sanity-check to ALT_UP() to ensure that
the content really is the right size (4 bytes).
(No check is done for ALT_SMP(). Possibly, this could be fixed
by splitting the two uses ot ALT_SMP() (ALT_SMP...SMP_UP versus
ALT_SMP...SMP_UP_B) into two macros. In the first case,
ALT_SMP needs to expand to >= 4 bytes, not == 4.)
* smp_mpidr.h (which implements ALT_SMP()/ALT_UP() manually due
to macro limitations) has not been modified: the affected
instruction (mov) has no 16-bit encoding, so the correct
instruction size is satisfied in this case.
* A "mode" parameter has been added to smp_dmb:
smp_dmb arm @ assumes 4-byte instructions (for ARM code, e.g. kuser)
smp_dmb @ uses W() to ensure 4-byte instructions for ALT_SMP()
This avoids assembly failures due to use of W() inside smp_dmb,
when assembling pure-ARM code in the vectors page.
There might be a better way to achieve this.
* Kconfig: make SMP_ON_UP depend on
(!THUMB2_KERNEL || !BIG_ENDIAN) i.e., THUMB2_KERNEL is now
supported, but only if !BIG_ENDIAN (The fixup code for Thumb-2
currently assumes little-endian order.)
Tested using a single generic realview kernel on:
ARM RealView PB-A8 (CONFIG_THUMB2_KERNEL={n,y})
ARM RealView PBX-A9 (SMP)
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
iwmmxt is used in XScale, XScale3, Mohawk and PJ4 core. But the instructions
of accessing CP0 and CP1 is changed in PJ4. Append more files to support
iwmmxt in PJ4 core.
Signed-off-by: Zhou Zhu <zzhu3@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Because the nwfpe support is unlikely to be used on new platforms
and requires CONFIG_OABI_COMPAT, which is not generally used with
ARMv7+, we shouldn't expect to build nwfpe support into a Thumb-2
kernel.
At present, nwfpe contains assembly code which isn't Thumb-2
compatible, and for now it doesn't appear useful to port this
code.
All ARMv7-A/R platforms necessarily have VFPv3 hardware floating-
point natively, making emulation unnecessary.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This makes sense, because Thumb-2 code can't execute on plain
ARMv6 processors.
This will avoid accidentally configuring a broken kernel where the
config otherwise would allow multiple architecture versions to
coexist in the same kernel.
Not adding !CPU_V5 etc., because the chance of anyone trying to
put v5 and v7 in the same kernel is low, and I'm not aware of
any mach which can do this. These could be added later if it
matters.
Note that the rules may need to be refined if support for the
ARM1156J(F)-S processor is later added to the kernel, since this
processor supports the rare ARMv6T2 extensions, which add support
for Thumb-2 and a few other ARMv7 features.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It is kernel-wide policy that options depending on EXPERIMENTAL should
also have '(EXPERIMENTAL)' in their option text, and options with
'(EXPERIMENTAL)' depend on EXPERIMENTAL.
Ensure that all ARM options comply with this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Today more boards with arm cpu have selectable pci bus.
This patch makes this more scalable and remove line continuations in
Kconfig
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Depending on the compiler version, ARM GCC calls the mcount function
either __gnu_mcount_nc or mcount.
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, the kprobes implementation for ARM only supports the ARM
instruction set, so it only works if CONFIG_THUMB2_KERNEL is not
enabled.
Until kprobes is updated to work with Thumb-2, turning it on will
cause horrible things to happen, so this patch disables it for now.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add CONFIG_CRASH_DUMP configuration option which is used by dump
capture kernels.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
factorise some generic infrastructure to assist looking up struct clks
for the ARM & SH architecture.
as the code is identical at 99%
put the arch specific code for allocation as example in asm/clkdev.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This just adds ARCH_MSM_SCORPIONMP to allow SMP selection for
MSM. MSM is unique in that it doesn't enable SCU or TWD.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add the options to enable the function graph tracer on ARM. Function
graph tracer support requires frame pointers, so exclude Thumb-2 and
also make sure FRAME_POINTER gets enabled when FUNCTION_GRAPH_TRACER is
used, since FUNCTION_TRACER doesn't "select FRAME_POINTER" when
ARM_UNWIND is used. Therefore, with GCC 4.4.0+, you get plain function
tracing without frame pointers, but you'll need them if you want
function graph tracing.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Presently each one of the CPUs manually selects the same feature set, and
there's a reasonable expectation that none of these will change for
future CPUs in the SH-Mobile / R-Mobile family, so we move those over to
the top-level ARCH_SHMOBILE.
While we're at it, all of the CPUs support optional GPIOs via the PFC,
do not have I/O ports, and expect sparse IRQ, so we bring the
configuration in line across the board.
This more or less brings the ARM-based parts in sync with their SH
counterparts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The old apcs-gnu ABI doesn't guarantee that double words are allocated
to registers with even alignment, causing the 64-bit exclusive memory
operations to be rejected by the assembler.
This patch requires that CONFIG_AEABI is set in order to use the native
atomic operations and falls back to the generic (spinlock) code otherwise.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (215 commits)
ARM: memblock: setup lowmem mappings using memblock
ARM: memblock: move meminfo into find_limits directly
ARM: memblock: convert free_highpages() to use memblock
ARM: move freeing of highmem pages out of mem_init()
ARM: memblock: convert memory detail printing to use memblock
ARM: memblock: use memblock to free memory into arm_bootmem_init()
ARM: memblock: use memblock when initializing memory allocators
ARM: ensure membank array is always sorted
ARM: 6466/1: implement flush_icache_all for the rest of the CPUs
ARM: 6464/2: fix spinlock recursion in adjust_pte()
ARM: fix memblock breakage
ARM: 6465/1: Fix data abort accessing proc_info from __lookup_processor_type
ARM: 6460/1: ixp2000: fix type of ixp2000_timer_interrupt
ARM: 6449/1: Fix for compiler warning of uninitialized variable.
ARM: 6445/1: fixup TCM memory types
ARM: imx: Add wake functionality to GPIO
ARM: mx5: Add gpio-keys to mx51 babbage board
ARM: imx: Add gpio-keys to plat-mxc
mx31_3ds: Fix spi registration
mx31_3ds: Fix the logic for detecting the debug board
...
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (38 commits)
kbuild: convert `arch/tile' to the kconfig mainmenu upgrade
README: cite nconfig
Revert "kconfig: Temporarily disable dependency warnings"
kconfig: Use PATH_MAX instead of 128 for path buffer sizes.
kconfig: Fix realloc usage()
kconfig: Propagate const
kconfig: Don't go out from read config loop when you read new symbol
kconfig: fix menuconfig on debian lenny
kbuild: migrate all arch to the kconfig mainmenu upgrade
kconfig: expand file names
kconfig: use the file's name of sourced file
kconfig: constify file name
kconfig: don't emit warning upon rootmenu's prompt redefinition
kconfig: replace KERNELVERSION usage by the mainmenu's prompt
kconfig: delay gconf window initialization
kconfig: expand by default the rootmenu's prompt
kconfig: add a symbol string expansion helper
kconfig: regen parser
kconfig: implement the `mainmenu' directive
kconfig: allow PACKAGE to be defined on the compiler's command-line
...
Fix up trivial conflict in arch/mn10300/Kconfig
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
This patch adds ARCH_HAS_CPUFREQ in arch/arm/Kconfig for S5PV210,
and updates mach-s5pv210/Makefile for supporting build CPUFREQ driver.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S5PV310 and S5PC210 support more I2C devices than previous SoCs.
Add the device support code for them.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Currently, only two operating points: 160Mhz and 800Mhz.
the operating points are tested on babbage 3.0
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Implement cpufreq support for the Tegra SOC. DVFS is handled by the
core virtual cpu clock. The frequencies of the two cores are tied
together, the highest frequency requested by either core determines
the actual frequency.
Signed-off-by: Colin Cross <ccross@android.com>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (278 commits)
arm: remove machine_desc.io_pg_offst and .phys_io
arm: use addruart macro to establish debug mappings
arm: return both physical and virtual addresses from addruart
arm/debug: consolidate addruart macros for CONFIG_DEBUG_ICEDCC
ARM: make struct machine_desc definition coherent with its comment
eukrea_mbimxsd-baseboard: Pass the correct GPIO to gpio_free
cpuimx27: fix compile when ULPI is selected
mach-pcm037_eet: fix compile errors
Fixing ethernet driver compilation error for i.MX31 ADS board
cpuimx51: update board support
mx5: add cpuimx51sd module and its baseboard
iomux-mx51: fix GPIO_1_xx 's IOMUX configuration
imx-esdhc: update devices registration
mx51: add resources for SD/MMC on i.MX51
iomux-mx51: fix SD1 and SD2's iomux configuration
clock-mx51: rename CLOCK1 to CLOCK_CCGR for better readability
clock-mx51: factorize clk_set_parent and clk_get_rate
eukrea_mbimxsd: add support for DVI displays
cpuimx25 & cpuimx35: fix OTG port registration in host mode
i.MX31 and i.MX35 : fix errate TLSbo65953 and ENGcm09472
...
In case of S5PV310/S5PC210, it uses the SPARSEMEM as default memory
configuration. So moved to ARCH_S5PV310 config.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: edited title]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In case of S5PV210/S5PC110, it uses the SPARSEMEM as default memory
configuration. So moved to ARCH_S5PV210 config.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: edited title]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support Watchdog Timer for S5PV310 and S5PC210.
Signed-off-by: Jemings Ko <jemings@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support RTC for S5PV310 and S5PC210.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Jemings Ko <jemings@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Provide a mechanism that allows running code in IRQ context. It is
most useful for NMI code that needs to interact with the rest of the
system -- like wakeup a task to drain buffers.
Perf currently has such a mechanism, so extract that and provide it as
a generic feature, independent of perf so that others may also
benefit.
The IRQ context callback is generated through self-IPIs where
possible, or on architectures like powerpc the decrementer (the
built-in timer facility) is set to generate an interrupt immediately.
Architectures that don't have anything like this get to do with a
callback from the timer tick. These architectures can call
irq_work_run() at the tail of any IRQ handlers that might enqueue such
work (like the perf IRQ handler) to avoid undue latencies in
processing the work.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[ various fixes ]
Signed-off-by: Huang Ying <ying.huang@intel.com>
LKML-Reference: <1287036094.7768.291.camel@yhuang-dev>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The patch below updates broken web addresses in the arch directory.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch updates the Kconfig and Makefile for the S5P6440 and S5P6450
machines. It also updates arch/arm/ Kconfig and Makefile to include for
support ARCH_S5P64X0 with one kernel image.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In order for CPUidle to work on SMP systems, an implementation of
cpu_idle_wait() is needed.
This patch duplicates the x86 implementation of cpu_idle_wait() for
ARM.
Tested-by: Colin Cross <ccross@android.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Do this by adding flush_icache_all to cache_fns for ARMv6 and 7.
As flush_icache_all may neeed to be called from flush_kern_cache_all,
add it as the first entry in the cache_fns.
Note that now we can remove the ARM_ERRATA_411920 dependency
to !SMP so it can be selected on UP ARMv6 processors, such
as omap2.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
UP systems do not implement all the instructions that SMP systems have,
so in order to boot a SMP kernel on a UP system, we need to rewrite
parts of the kernel.
Do this using an 'alternatives' scheme, where the kernel code and data
is modified prior to initialization to replace the SMP instructions,
thereby rendering the problematical code ineffectual. We use the linker
to generate a list of 32-bit word locations and their replacement values,
and run through these replacements when we detect a UP system.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All platforms which currently support SMP also support the ARM SCU
and ARM TWD blocks, so it's pointless to make these config symbols
conditional on the platform symbols which SMP is already conditional
on.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On the r2p0, r2p1 and r2p2 versions of the Cortex-A9, data corruption
can occur under very rare conditions due to a store buffer optimisation.
This workaround sets a bit in the diagnostic register of the Cortex-A9,
disabling the optimisation and preventing the problem from occurring.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
update OMAP Kconfig help texts for all supported SoC models
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
5cfc8ee0bb (ARM: convert arm to arch_gettimeoffset()) marked all of
at91 AND at91x40 as needing ARCH_USES_GETTIMEOFFSET, and hence no high
res timer support / accurate clock_gettime() - But only at91x40 needs it.
Cc: stable@kernel.org
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch introduces support for the tcc platform by creating an
arch/arm/plat-tcc and arch/arm/mach-tcc8k directories and adding
basic include files plus Kconfig and Makefile.
Signed-off-by: "Hans J. Koch" <hjk@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On the r2p0, r2p1 and r2p2 versions of the Cortex-A9, data corruption
can occur if a shared cache line is replaced on one CPU as another CPU
is accessing it.
This workaround sets two bits in the diagnostic register of the Cortex-A9,
reducing the linefill issuing capabilities of the processor and
avoiding the erroneous behaviour.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On versions of the Cortex-A9 up to and including r2p2, under rare
circumstances, a DMB instruction between 2 write operations may not
ensure the correct visibility ordering of the 2 writes.
This workaround sets a bit in the diagnostic register of the Cortex-A9,
causing the DMB instruction to behave like a DSB, which functions
correctly on the affected cores.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Partially revert e69edc7, which introduced automatic zreladdr
support. The change in the way the manual definition is defined
seems to be error and conflict prone. Go back to the original way
we were handling this for the time being, while keeping the automatic
zreladdr facility.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If we're targetting a v6 or v7 core and have at least software perf events
available, then automatically add support for hardware breakpoints.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: S. Karthikeyan <informkarthik@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dynamic ftrace for ARM has been disabled since 07c4cc1cda ("ftrace:
disable dynamic ftrace for all archs that use daemon"). Now that the
code has been updated, re-enable it.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fixes the warning:
.config:369:warning: symbol value '' invalid for ZRELADDR
and the prompt for ZRELADDR on make
Signed-off-by: Erik Gilling <konkers@android.com>
On versions of the Cortex-A9 prior to r2p0, performing TLB invalidations by
ASID match can result in the incorrect ASID being broadcast to other CPUs.
As a consequence of this, the targetted TLB entries are not invalidated
across the system.
This workaround changes the TLB flushing routines to invalidate entries
regardless of the ASID.
Cc: <stable@kernel.org>
Tested-by: Rob Clark <rob@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'timers-timekeeping-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
um: Fix read_persistent_clock fallout
kgdb: Do not access xtime directly
powerpc: Clean up obsolete code relating to decrementer and timebase
powerpc: Rework VDSO gettimeofday to prevent time going backwards
clocksource: Add __clocksource_updatefreq_hz/khz methods
x86: Convert common clocksources to use clocksource_register_hz/khz
timekeeping: Make xtime and wall_to_monotonic static
hrtimer: Cleanup direct access to wall_to_monotonic
um: Convert to use read_persistent_clock
timkeeping: Fix update_vsyscall to provide wall_to_monotonic offset
powerpc: Cleanup xtime usage
powerpc: Simplify update_vsyscall
time: Kill off CONFIG_GENERIC_TIME
time: Implement timespec_add
x86: Fix vtime/file timestamp inconsistencies
Trivial conflicts in Documentation/feature-removal-schedule.txt
Much less trivial conflicts in arch/powerpc/kernel/time.c resolved as
per Thomas' earlier merge commit 47916be4e2 ("Merge branch
'powerpc.cherry-picks' into timers/clocksource")
This patch moves the dependency of watchdog timer driver from MACH_XXX(board)
to ARCH_XXX(SoC). This will enable all machines using Samsung S3C64XX and S5P
SoCs to use the WDT driver by default.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Conflicts:
arch/arm/Kconfig
arch/arm/mach-s3c64xx/Kconfig
arch/arm/mach-s5p6442/Kconfig
arch/arm/mach-s5pc100/Kconfig
v2: fixes from Russell King:
- include linux/io.h instead of asm/io.h
- fix whitespace in Kconfig
- Use spin_lock_init to initialize lock
- Return -ENOSYS instead of BUG for unimplemented clock ops
- Use proper return values in tegra2 clock ops
additional changes:
- Rename some clocks to match dev_ids
- add rate propagation
- add debugfs entries
- add support for clock listed in clk_lookup under multiple dev_ids
v3:
- Replace per-clock locking with global clock lock
- Autodetect clock state on init
- Let clock dividers pick next lower possible frequency
- Add support for clock init tables
- Minor bug fixes
- Fix checkpatch issues
Signed-off-by: Colin Cross <ccross@android.com>
v2: Fixes from Mike Rapoport
- remove unused header files (mach/dma.h and mach/nand.h)
- remove tegra 1 references from Makefile.boot
v2: fixes from Russell King
- remove mach/io.h include from mach/iomap.h
- fix whitespace in Kconfig
v2: from Colin Cross
- fix invalid immediate in debug-macro.S
v3:
- allow selection of multiple boards
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Erik Gilling <konkers@android.com>
This patch adds HAVE_S3C2410_I2C to control inclusion of I2C bus driver
on Samsung SoCs and makes I2C bus driver dependency SoC specific instead
of machine specific. This will enalbe all machines using Samsung ARCH_S3C2410,
_S3C64XX, _S5P6440, _S5PC100, and _S5PV210 to select the I2C driver by default
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
This patch moves the dependency of RTC driver from MACH_XXX(board) to
ARCH_XXX(SoC). This will enable all machines using Samsung S5P6440, S5PC100
and S5PV210 SoCs to use RTC driver by default.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the Kconfig and Makefile for the new S5PV310 SoC.
It also updates arch/arm Kconfig, Makefile and arch/arm/mm/Kconfig
to include support for the new S5PV310.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Introduce SHMOBILE_TIMER_HZ for SH-Mobile.
Allow users to select HZ on their system to
minimize potential timer drift. Use 128 Hz as
default to work well with the 32768 Hz RCLK.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add LPC32XX support in arch/arm/Kconfig and arch/arm/Makefile
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Now that all arches have been converted over to use generic time via
clocksources or arch_gettimeoffset(), we can remove the GENERIC_TIME
config option and simplify the generic code.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1279068988-21864-4-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The TWD local timers are unable to wake up the CPU when it is placed
into a low power mode, eg. C3. Therefore, we need to adapt things
such that the TWD code can cope with this.
We do this by always providing a broadcast tick function, and marking
the fact that the TWD local timer will stop in low power modes. This
means that when the CPU is placed into a low power mode, the core
timer code marks this fact, and allows an IPI to be given to the core.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
SPARSE_IRQ doesn't need to be a visible option, only those platforms
supporting that will select it.
Signed-off-by: Eric Miao <eric.miao@canonical.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Everything should now be using sparsemem rather than discontigmem, so
remove the code supporting discontigmem from ARM.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As long as the zImage is placed within the 128MB range from the start of
memory, ZRELADDR (Address where the decompressed kernel will be placed,
usually == PHYS_OFFSET + TEXT_OFFSET) can be determined at run-time by
masking PC with 0xf80000000.
Running through all the Makefile.boot, all those zreladdr-y
addresses == 0x[0-f][08]00_0000 + TEXT_OFFSET can be determined at
run-time.
Option CONFIG_AUTO_ZRELADDR and CONFIG_ZRELADDR are introduced,
CONFIG_ZRELADDR _must_ be explicitly specified if:
- ((zreladdr-y - TEXT_OFFSET) & ~0xf8000000) != 0, which means
masking PC with 0xf8000000 will result in an incorrect address.
Currently this is only a problem on u300.
- or the assumption of the zImage being loaded by the bootloader within
the first 128MB of RAM is incorrect
- or when ZBOOT_ROM is used, where the above assumption is usually wrong.
[ukleinek: changed mask from 0xf0000000 to 0xf8000000 for mx1 and shark
+ some review fixes from the mailing list]
Original-Idea-and-Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Eric Miao <eric.miao@canonical.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Allow SH-Mobile ARM users to adjust FORCE_MAX_ZONEORDER.
The Kconfig entry is taken from SH and non-4K page size
stuff has been trimmed away. For now only SH-Mobile ARM is
allowed to change this variable, SA1111 configs are kept at
"9" and the rest at "11".
CONFIG_FORCE_MAX_ZONEORDER lets the user tweak the maximum
amount of physically contiguous memory that can be allocated
by the kernel.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch enables the HAVE_REGS_AND_STACK_ACCESS_API option
for ARM which is required by the kprobe events tracer. Code based
on the PowerPC port.
Cc: Jean Pihet <jpihet@mvista.com>
Tested-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
So to allow NR_IRQS to be dynamic and platforms to specify the number
of IRQs really needed.
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for the Cortex-A9 local timers available when
using the CA9X4 daughterboard with the Versatile Express.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This was deprecated in 2001 and announced to live on for 5 years.
For now provide a kernel parameter for those who still need it.
Acked-by: Eric Miao <eric.miao@canonical.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
CPU performance event counters on v7 cores will only operate
if either the NIDEN or DBGEN signals are driven high.
For the OMAP3 platform, these signals are driven low by default
but DBGEN can be asserted by selecting the OMAP3_EMU Kconfig option,
which enables the virtual clock for hardware debugging peripherals.
Acked-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This hasn't been actively maintained for a long time, only receiving
the occasional build update when things break. I doubt anyone has
one of these on their desks anymore.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[dwalker@codeaurora.org: renamed to trout, checkpatch cleanup]
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
This is the very basic stuff without the changing canary upon
task switch yet. Just the Kconfig option and a constant canary
value initialized at boot time.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
This patch adds PCIe support for CNS3xxx-based boards. The support
was tested with a directly attached SKY2 NIC, and EHCI USB controller
behind the PLX PEX8112 P2P bridge (to make sure that type1 cfg cycles
work as expected).
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Add an option to force usage of the in-kernel cmdline even if the boot
loader passes another command string to the kernel.
Useful if someone cannot or don't want to change the
command-line options of the boot loader but is able to change
the kernel.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixup commit 5cfc8ee0bb which
introduced ARCH_USES_GETTIMEOFFSET but missed out several
S5P architectures.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch moves S5PC100 SoC support to plat-s5p framework. Most
periperal support code has been already moved from plat-s5pc1xx to
mach-s5pc100.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (48 commits)
Revert "rtc: omap: let device wakeup capability be configured from chip init logic"
DM365: Added more PINMUX configurations for AEMIF
DM365: Make CLKOUTx available
DM365: Added PINMUX definitions for GPIO30..32
Davinci: iotable based ioremap() interception
Davinci: pinmux - use ioremap()
Davinci: aintc/cpintc - use ioremap()
Davinci: psc - use ioremap()
Davinci: timer - use ioremap()
Davinci: jtag_id - use ioremap()
Davinci: da8xx: rtc - use ioremap
Davinci: gpio - use ioremap()
davinci: edma: fix coding style issue related to breaking lines
davinci: edma: use BIT() wherever possible
davinci: edma: fix coding style issue related to usage of braces
davinci: edma: use a more intuitive name for edma_info
Davinci: serial - conditional reset via pwremu
Davinci: serial - use ioremap()
Davinci: serial - remove unnecessary define
Davinci: watchdog reset separation across socs
...
Fix up trivial conflict in arch/arm/Kconfig due to removal of "select
GENERIC_TIME"
The ARCH_REQUIRE_GPIOLIB config option will select GPIOLIB which
in turn will select GENERIC_GPIO. Because of this, there is no
reason to do the select GENERIC_GPIO in arch/arm/Kconfig for the
architectures that have ARCH_REQUIRE_GPIOLIB.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enable hardware perf-events if CPU_HAS_PMU and select
HAVE_OPROFILE if HAVE_PERF_EVENTS. If no hardware support
is present, OProfile will fall back to timer mode.
This patch also removes the old OProfile drivers in favour
of the code implemented by perf.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add arch/arm/mach-s3c2416 for support of the Samsung S3C2416 SoC.
This patch adds support of the S3C2416 SoC, clocks, timers,
and initial IRQ support (without support of secondary set of registers).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
[ben-linux@fluff.org: removed files to be reworked, fixed conflicts]
[ben-linux@fluff.org: use s3c2443 reset instead of specific reset code]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Preliminary modification prior to adding support for TNETV107X based on
ARM1176. This change allows for CPUs other than ARM926T to be used for Davinci
derivative SoCs. Existing devices (DA8x and DMx) operate unchanged.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
ARCH_MSM supports armv7 cpus, so we're pushed the CPU_V6/CPU_V7 selection
down into the arch/arm/mach-msm/Kconfig.
Also update the description to be a bit more accurate.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
This patch adds very basic support for ECONA CNS3xxx ARM11 MPcore
(ARMv6) dual-core processors.
Note that SMP is not yet supported, as well as many peripheral
devices. Support for these features will be added later.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
The only difference between ICST307 and ICST525 are the two arrays
for calculating the S parameter; the code is now identical. Merge
the two files and kill the duplicated code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The switch to using GPIOLIB broke the sd/mmc card detection on the
RealView development boards if GPIO_PL061 was not selected.
This patch selects GPIO_PL061 if GPIOLIB is selected.
The sense of the return value from mmc_status has also changed
and is corrected.
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for PCI domains on ARM platforms.
Also, protect asm/mach/pci.h from multiple inclustions, otherwise
build fails because of pci_domain_nr() and pci_proc_domain()
redefinitions.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch allows using a kernel image compressed with LZMA on ARM.
Extracting the image is fairly slow, but it might be useful on machines
with a very limited amount of storage, as the size benefit is quite
significant (about 25% smaller with LZMA compared to GZIP)
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Tested-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert arm to use GENERIC_TIME via the arch_getoffset() infrastructure,
reducing the amount of arch specific code we need to maintain.
The arm architecture is the last arch that need to be converted.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Add support for the GPIOs on the U8500, using the plat-nomadik GPIO
driver.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (370 commits)
ARM: S3C2443: Add set_rate and round_rate calls for armdiv clock
ARM: S3C2443: Remove #if 0 for clk_mpll
ARM: S3C2443: Update notes on MPLLREF clock
ARM: S3C2443: Further clksrc-clk conversions
ARM: S3C2443: Change to using plat-samsung clksrc-clk implementation
USB: Fix s3c-hsotg build following Samsung platform header moves
ARM: S3C64XX: Reintroduce unconditional build of audio device
ARM: 5961/1: ux500: fix CLKRST addresses
ARM: 5977/1: arm: Enable backtrace printing on oops when PC is corrupted
ASoC: Fix S3C64xx IIS driver for Samsung header reorg
ARM: S3C2440: Fix plat-s3c24xx move of s3c2440/s3c2442 support
[ARM] pxa: fix typo in mxm8x10.h
[ARM] pxa/raumfeld: set GPIO drive bits for LED pins
[ARM] pxa/zeus: Add support for mcp2515 CAN bus
[ARM] pxa/zeus: Add support for onboard max6369 watchdog
[ARM] pxa/zeus: Add Eurotech as the manufacturer
[ARM] pxa/zeus: Correct the USB host initialisation flags
[ARM] pxa/zeus: Allow usage of 8250-compatible UART in uncompress
[ARM] pxa: refactor uncompress.h for non-PXA uarts
[ARM] mmp2: fix incorrect calling of chip->mask_ack() for 2nd level cascaded IRQs
...
Marvell MMP2 (aka ARMADA610) is a SoC based on PJ4 core. It's
ARMv6 compatible. Support basic interrupt handler and timer,
and basic support for MMP2 based FLINT platform.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Updates arch/arm Kconfig and Makefile for building the S5PV210 support.
Also modifies the plat-s5p Kconfig file to include the support for plat-s5p
for S5PV210.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add ARM_L1_CACHE_SHIFT_6 to arch/arm/Kconfig to allow CPUs with
L1 cache lines which are 64bytes to indicate this without having to
alter the arch/arm/mm/Kconfig entry each time.
Update the mm Kconfig so that ARM_L1_CACHE_SHIFT default value
uses this and change OMAP3 and S5PC1XX to select ARM_L1_CACHE_SHIFT_6.
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is broken since at least one year when
ec996ba (mxc timer: make compile time independent)
removed the symbol MXC_TCN.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Updates arch/arm Kconfig and Makefile for building the S5P6442 support.
Also modifies the plat-s5p Kconfig file to include the support for plat-s5p
for S5P6442.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the Kconfig entries from plat-s3c to plat-samsung and plat-s3c24xx
as necessary. The S3C_BOOT entries and the DMA configuration can go to
plat-samsung. The low-level UART configurations are currently S3C2XX
specific and can go to plat-s3c24xx.
Eliminating plat-s3c from the build process will be submitted seperately.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Remove the Kconfig and PLAT_S3C64XX defines for the previous S3C64XX
directory structure now that the code is moved into mach-s3c64xx.
Note, we cannot currently remove plat-s3c64xx directory as we have a
pair of include files used within plat-s3c and plat-samsung that need
to find a new home.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch implements the work-around for the errata 588369.The secure
API is used to alter L2 debug register because of trust-zone.
This version updated with comments from Russell and Catalin and
generated against 2.6.33-rc6 mainline kernel. Detail
comments can be found:
http://www.spinics.net/lists/linux-omap/msg23431.html
Signed-off-by: Woodruff Richard <r-woodruff2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In preparation for perf-events support, ARM needs to support atomic64_t
operations. v6k and above support the ldrexd and strexd instructions to
do just that.
This patch adds atomic64 support to the ARM architecture. v6k and above
make use of new instructions whilst older cores fall back on the generic
solution using spinlocks. If and when v7-M cores are supported by Linux,
they will need to fall back on the spinlock implementation too.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Always creating this directory avoids other users having to jump
through silly hoops when they want to share this directory.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds the Performance Events support for ARMv7 processor, using
the PMNC unit in HW.
Supports the following:
- Cortex-A8 and Cortex-A9 processors,
- dynamic detection of the number of available counters,
based on the PMCR value,
- runtime detection of the CPU arch (v6 or v7)
and model (Cortex-A8 or Cortex-A9)
Tested on OMAP3 (Cortex-A8) only.
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch implements support for ARMv6 performance counters in the
Linux performance events subsystem. ARMv6 architectures that have the
performance counters should enable HW_PERF_EVENTS to get hardware
performance events support in addition to the software events.
Note: only ARM Ltd ARM cores are supported.
This implementation also provides an ARM PMU abstraction layer to allow
ARMv7 and others to be supported in the future by adding new a
'struct arm_pmu'.
Cc: Jean Pihet <jpihet@mvista.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The perf events subsystem allows counting of both hardware and
software events. This patch implements the bare minimum for software
performance events.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To add support for perf events and to allow the hardware counters to be
shared with oprofile, we need a way to reserve access to the pmu
(performance monitor unit). Platforms with PMU interrupts should
register the interrupts in arch/arm/kernel/pmu.c
Signed-off-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds preliminary support for the SH-Mobile G-series.
The SH-Mobile G-series is a series of ARM/SH multi-core CPUs that aside
from the ARM MPU are primarily composed of existing SH IP blocks.
This includes initial support for the SH7367 (SH-Mobile G3) CPU and
the G3EVM reference board.
Only timer, serial console, and NOR flash are supported at this point.
Patches for the interrupt controller, pinmux support, clock framework
and runtime pm will be submitted as feature patches on top of this.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
OMAP platforms(like OMAP3530) include DSP or other co-processors
for media acceleration. when carving out memory for the
accelerators we can end up creating a hole in the memory map
of sort:
<kernel memory><hole(memory for accelerator)><kernel memory>
To handle such a memory configuration ARCH_HAS_HOLES_MEMORYMODEL
has to be enabled. For further information refer discussion at:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg15262.html.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the old mach-s3c2442 directory now all is merged into mach-s3c2440
and remove it from the arch/arm build process.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The previous nuc932 support patches have been discarded by me and because it belongs to
another SoCs series named nuc93x,at present, which included nuc931 and nuc932, I think it is
better to create a new mach-nuc93x,So I made the patch,and request your advice.Thanks!
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per discussions with Russell King on linux-arm-kernel, it appears that
both mach-s3c6400 and mach-s3c6410 are so close together that they should
simply be merged into mach-s3c64xx.
Note, this patch does not eliminate any of the bits that are still common,
it is simply a move of the two directories together, any further common
code will be eliminated or moved in further patches.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds the Kconfig and Makefile for the new S5P6440 machine
and platform directories. It also updates arch/arm Kconfig and Makefiles
to include the support for the new S5P6440 CPU.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
- changes to ach/arch/boot/Makefile to make it easier to add new
compression types
- new piggy.lzo.S necessary for lzo compression
- changes in arch/arm/boot/compressed/misc.c to allow the use of lzo or
gzip, depending on the config
- Kconfig support
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All DaVinci platforms include a DSP or co-processor for
audio/video acceleration.
While creating memory for the DSP/co-processor, system
integrator can end up creating a hole in the memory map
of the sort:
<kernel memory> <hole (memory for DSP)> <kernel memory>
This sort of configuration needs ARCH_HAS_HOLES_MEMORYMODEL
enabled. See further details see this discussion on ARM
linux mailing list:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg15262.html
The patch is boot tested on OMAP-L138, DM6446 and DM355 EVMs
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
CC: Sriramakrishnan <srk@ti.com>
CC: Khasim Syed Mohammed <khasim@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Fix:
arch/arm/mach-sa1100/generic.c:117: error: redefinition of 'cpufreq_get'
include/linux/cpufreq.h:299: error: previous definition of 'cpufreq_get' was here
cpufreq_get() is used on these platforms to tell drivers what the CPU
frequency is, and therefore the bus frequency - which is critical for
setting the PCMCIA and LCD timings. Adding ifdefs to these drivers to
select cpufreq_get() or some other interface adds confusion. Making
these drivers use some other interface for the normal paths and cpufreq
stuff for the cpufreq notifier is insane as well.
(Why x86 can't provide a version of cpufreq_get() which returns the
CPU frequency when CPUFREQ is disabled is beyond me, rather than
requiring a dummy zero-returning cpufreq_get(). Especially as they
do:
unsigned long khz = cpufreq_get(cpu);
if (!khz)
khz = tsc_khz;
In other words, if CPUFREQ is disabled, get it from tsc_khz - why
not provide a dummy cpufreq_get() which returns tsc_khz?)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We inted to re-organise the plat-s3c/plat-s3c24xx/plat-s3c64xx into a
more generic plat-samsung with less code in the other plat- directories
to make it easier to port new devices and try and clear up some of the
naming issues with newer devices.
Start by creating a small arch/arm/plat-samsung with no actuall code in
so we can move items in as we process them.
Add this to arch/arm to allow it to build things once support is added.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This hooks the U8500 support into the ARM kbuild
system. This integration also enables SMP and its
helper functions for U8500 platform
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce the plat-nomadik folder for ST-Ericsson
machines including the existing nomadik 8815 architecture.
This also moves the existing MTU (MultiTimerUnit)
of nomadik 8815 to the proposed plat-nomadik and adds
HAS_MTU. The patch has been re-based to 2.6.32-rc6
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Marvell Dove (88AP510) is a high-performance, highly integrated,
low power SoC with high-end ARM-compatible processor (known as PJ4),
graphics processing unit, high-definition video decoding acceleration
hardware, and a broad range of peripherals.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This updates the IOP platform to use the kernel's generic time
framework. With clockevent support in place, this reduces to
selecting GENERIC_TIME and removing the platform's private timer
->offset() operation (iop_gettimeoffset).
Tested on n2100, compile-tested for all plat-iop machines.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This updates the IOP platform to expose the interrupting
timer 0 as a clockevent object. The timer interrupt handler
is changed to call the clockevent ->event_handler() instead
of timer_tick(), and ->set_next_event() and ->set_mode()
operations are added to allow the mode of the timer to be
updated (required for ONESHOT/NOHZ mode).
Timer 0 must now be properly initialised, which requires
a new write_tcr0() function from the mach-specific code.
The mode of timer 0 must be read at the start of ->set_mode(),
which requires a new read_tmr0() function from the mach-
specific code.
Initial setup of timer 0 is also rewritten to be more robust.
Tested on n2100, compile-tested for all plat-iop machines.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This adds the TCM interface to Linux, when active, it will
detect and report TCM memories and sizes early in boot if
present, introduce generic TCM memory handling, provide a
generic TCM memory pool and select TCM memory for the U300
platform.
See the Documentation/arm/tcm.txt for documentation.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the ARM implementation of highpte, which allows PTE tables to be
placed in highmem. Unfortunately, we do not offer highpte support
when support for L2 cache is enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
S5PC100 is a new SoC with ARM coretex-A8 and numerous peripherals. This SoC is
successor of S3C64XX. S5PC100 has peripherals which are still similar to S3C
families so some drivers in "arch/arm/plat-s3c" can be shared. S5PC100 specific
drivers will be added in "arch/arm/plat-s5pcxx" or "arch/arm/mach-s5pc100"
Signed-off-by: Byungho Min <bhmin@samsung.com>
[ben-linux@fluff.org: tidy and edit description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
add bcmring option in Kconfig and add entry in Makefile
in arch/arm directory
Signed-off-by: Leo Chen <leochen@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide more useful introduction for w90x900
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add clocksource/clockevent support for w90p910 platform.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The changes introduced by this change are:
- drivers/mtd/Kconfig doesn't depend on ALIGNMENT_TRAP ||
!CPU_CP15_MMU any more
- the following files are sourced additionally:
+ drivers/macintosh/Kconfig
completely depends on PPC || MAC || X86
+ drivers/telephony/Kconfig
new
+ drivers/pps/Kconfig
new
+ drivers/infiniband/Kconfig
new
+ drivers/edac/Kconfig
depends on X86 || PPC
+ drivers/vlynq/Kconfig
depends on AR7 && EXPERIMENTAL (that is ARCH_MIPS)
+ drivers/xen/Kconfig
everything depends on XEN
+ drivers/platform/Kconfig
depends on X86
- drivers/regulator/Kconfig is sourced later as is
drivers/accessibility/Kconfig
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
before this patch ARM had it's own definition of CONFIG_PREEMPT.
Instead of that use the general definition provided in
kernel/Kconfig.preempt.
This patch changes the available options in *config. Namely PREEMPT
isn't a stand alone bool anymore, but part of a 'choice' the
following Kconfig symbols are added:
PREEMPT_NONE
PREEMPT_VOLUNTARY
Selecting PREEMPT_NONE now produces exactly the code as not selecting
PREEMPT before (apart from a comment in
/sys/kernel/debug/tracing/(per_cpu/cpuX/)?trace). The only difference
PREEMPT_VOLUNTARY does is that might_resched might reschedule. Both
should't introduce regressions.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Add debugfs support for the cpufreq driver to allow
information about the system state to be exported to
the user.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the S3C24XX to the main ARM CPUFreq Kconfig support list.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add ARCH_HAS_CPUFREQ so that each machine config can select
it if they have CPUFREQ driver support. This means that the
CPUFREQ specific area does not need the if statement updating
each time a new machine is added.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds the necessary entries to the Makefile and Kconfig
files for building the Thumb-2 kernel.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds various C and assembler macros that help with using
the unified assembler syntax for compiling files to either ARM or
Thumb-2 modes.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add HAVE_CLK depends on for w90p910 platform.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the basic infrastructure for the Nomadik 8815
CPU and the "Nomadik Hardware Kit" NHK8815. This patch only
includes the serial console and core stuff, no drivers.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch provides initial support for CPU frequency scaling on the
Samsung S3C ARM processors. Currently only S3C6410 processors are
supported, though addition of another data table with supported clock
rates should be sufficient to enable support for further CPUs.
Use the regulator framework to provide optional support for DVFS in
the S3C cpufreq driver. When a software controllable regulator is
configured the driver will use it to lower the supply voltage when
running at a lower frequency, giving improved power savings.
When regulator support is disabled or no regulator can be obtained
for VDDARM the driver will fall back to scaling only the frequency.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is a RealView platform supporting core tiles with ARM11MPCore,
Cortex-A8 or Cortex-A9 (multicore) processors. It has support for MMC,
CompactFlash, PCI-E.
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This implements {copy_to,clear}_user() by faulting in the userland
pages and then using the regular kernel mem{cpy,set}() to copy the
data (while holding the page table lock). This is a win if the regular
mem{cpy,set}() implementations are faster than the user copy functions,
which is the case e.g. on Feroceon, where 8-word STMs (which memcpy()
uses under the right conditions) give significantly higher memory write
throughput than a sequence of individual 32bit stores.
Here are numbers for page sized buffers on some Feroceon cores:
- copy_to_user on Orion5x goes from 51 MB/s to 83 MB/s
- clear_user on Orion5x goes from 89MB/s to 314MB/s
- copy_to_user on Kirkwood goes from 240 MB/s to 356 MB/s
- clear_user on Kirkwood goes from 367 MB/s to 1108 MB/s
- copy_to_user on Disco-Duo goes from 248 MB/s to 398 MB/s
- clear_user on Disco-Duo goes from 328 MB/s to 1741 MB/s
Because the setup cost is non negligible, this is worthwhile only if
the amount of data to copy is large enough. The operation falls back
to the standard implementation when the amount of data is below a certain
threshold. This threshold was determined empirically, however some targets
could benefit from a lower runtime determined value for optimal results
eventually.
In the copy_from_user() case, this technique does not provide any
worthwhile performance gain due to the fact that any kind of read access
allocates the cache and subsequent 32bit loads are just as fast as the
equivalent 8-word LDM.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Provide a generic SRAM allocator using genalloc, and vaguely
modeled after what AVR32 uses. This builds on top of the
static CPU mapping set up in the previous patch, and returns
DMA mappings as requested (if possible).
Compared to its OMAP cousin, there's no current support for
(currently non-existent) DaVinci power management code running
in SRAM; and this has ways to deallocate, instead of being
allocate-only.
The initial user of this should probably be the audio code,
because EDMA from DDR is subject to various dropouts on at
least DM355 and DM6446 chips.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
pfn_valid() is meant to be able to tell if a given PFN has valid memmap
associated with it or not. In FLATMEM, it is expected that holes always
have valid memmap as long as there is valid PFNs either side of the hole.
In SPARSEMEM, it is assumed that a valid section has a memmap for the
entire section.
However, ARM and maybe other embedded architectures in the future free
memmap backing holes to save memory on the assumption the memmap is never
used. The page_zone linkages are then broken even though pfn_valid()
returns true. A walker of the full memmap must then do this additional
check to ensure the memmap they are looking at is sane by making sure the
zone and PFN linkages are still valid. This is expensive, but walkers of
the full memmap are extremely rare.
This was caught before for FLATMEM and hacked around but it hits again for
SPARSEMEM because the page_zone linkages can look ok where the PFN linkages
are totally screwed. This looks like a hatchet job but the reality is that
any clean solution would end up consumning all the memory saved by punching
these unexpected holes in the memmap. For example, we tried marking the
memmap within the section invalid but the section size exceeds the size of
the hole in most cases so pfn_valid() starts returning false where valid
memmap exists. Shrinking the size of the section would increase memory
consumption offsetting the gains.
This patch identifies when an architecture is punching unexpected holes
in the memmap that the memory model cannot automatically detect and sets
ARCH_HAS_HOLES_MEMORYMODEL. At the moment, this is restricted to EP93xx
which is the model sub-architecture this has been reported on but may expand
later. When set, walkers of the full memmap must call memmap_valid_within()
for each PFN and passing in what it expects the page and zone to be for
that PFN. If it finds the linkages to be broken, it assumes the memmap is
invalid for that PFN.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch-imx is superseeded by the MXC architecture support.
This patch removes arch-imx from the build system.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
All i.MX platforms support <linux/clk.h> calls and should select HAVE_CLK.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch is a workaround for the 460075 Cortex-A8 (r2p0) erratum. It
configures the L2 cache auxiliary control register so that the Write
Allocate mode for the L2 cache is disabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a workaround for the 458693 Cortex-A8 (r2p0)
erratum. It sets the corresponding bits in the auxiliary control
register so that the PLD instruction becomes a NOP.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the workaround for the 430973 Cortex-A8 (r1p0..r1p2)
erratum. The BTAC/BTB is now flushed at every context switch.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch implements the recommended workaround for erratum 411920
(ARM1136, ARM1156, ARM1176).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This hooks the U300 support into Kbuild and makes a small hook
in mmu.c for supporting an odd memory alignment with shared memory
on these systems.
This is rebased to RMK:s GIT HEAD. This patch tries to add the
Kconfig option in alphabetic order by option text and the Makefile
entry after config symbol.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Added Kconfig/Makefile entries for STMP platform
Signed-off-by: dmitry pervushin <dpervushin@embeddedalley.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
cpufreq drivers for pxa2xx/3xx are now built-in automatically as soon as
CPU_FREQ is enabled.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
ARCH_PXA selects HAVE_CLK and COMMON_CLKDEV twice in arch/arm/Kconfig.
Remove the second entry.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This is a significant rework of the low-level clock, PLL and Power
Sleep Controller (PSC) implementation for the DaVinci family. The
primary goal is to have better modeling if the hardware clocks and
features with the aim of DVFS functionality.
Highlights:
- model PLLs and all PLL-derived clocks
- model parent/child relationships of PLLs and clocks
- convert to new clkdev layer
- view clock frequency and refcount via /proc/davinci_clocks
Special thanks to significant contributions and testing by David
Brownell.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Adds support for Cortina Systems Gemini family CPUs:
http://www.cortina-systems.com/products/category/18
v3:
- fixed __io(a) to be defined as __typesafe_io(a)
v2:
- #include <asm/io.h> -> <linux/io.h>
- remove asm/system.h include
- revorked mm.c to use named initializers
- removed "empty" dma.h
- updated copyrights
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
"""The Marvell® PXA168 processor is the first in a family of application
processors targeted at mass market opportunities in computing and consumer
devices. It balances high computing and multimedia performance with low
power consumption to support extended battery life, and includes a wealth
of integrated peripherals to reduce overall BOM cost .... """
See http://www.marvell.com/featured/pxa168.jsp for more information.
1. Marvell Mohawk core is a hybrid of xscale3 and its own ARM core,
there are many enhancements like instructions for flushing the
whole D-cache, and so on
2. Clock reuses Russell's common clkdev, and added the basic support
for UART1/2.
3. Devices are a bit different from the 'mach-pxa' way, the platform
devices are now dynamically allocated only when necessary (i.e.
when pxa_register_device() is called). Description for each device
are stored in an array of 'struct pxa_device_desc'. Now that:
a. this array of device description is marked with __initdata and
can be freed up system is fully up
b. which means board code has to add all needed devices early in
his initializing function
c. platform specific data can now be marked as __initdata since
they are allocated and copied by platform_device_add_data()
4. only the basic UART1/2/3 are added, more devices will come later.
Signed-off-by: Jason Chagas <chagas@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
1. introduce folder of 'arch/arm/plat-pxa' for common code across different
PXA processor families
2. initially moved DMA code into plat-pxa
3. common code in <mach/dma.h> moved into <plat/dma.h>, new processors
should implement its own <mach/dma.h>, provide the following required
definitions and '#include <plat/dma.h>' in the end:
- DMAC_REGS_VIRT for mapped virtual address of the DMA registers'
physical I/O memory
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Here it is... HIGHMEM for the ARM architecture. :-)
If you don't have enough ram for highmem pages to be allocated and still
want to test this, then the cmdline option "vmalloc=" can be used with
a value large enough to force the highmem threshold down.
Successfully tested on a Marvell DB-78x00-BP Development Board with
2 GB of RAM.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Code has never been in buildable state since initial
merge.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for gpiolib, including debugfs output, to the AT91 family.
The at91_get/set_gpio_value calls still exist since they are used by the
atmel serial driver.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The new Kconfig option to build "staging" drivers (code in
drivers/staging/) is seen in all except three architectures (arm, h8300,
cris), because in these cases arch/$ARCH/Kconfig does NOT source
drivers/Kconfig.
This patch adds the source "drivers/staging/Kconfig" to
arch/$ARCH/Kconfig for these three exceptional cases.
Signed-off-by: Duncan Haldane <duncan_h@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is as small a change as possible to the KS8695 GPIO layer
to use GPIOLIB to allow the generic GPIO expanders and the like to
be compiled.
As a side-effect, we also remove __init_or_module from several
functions which could be called by drivers such as i2c-gpio which
could plausibly be compiled into a non-modular kernel.
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is based on a patch by Luotao Fu <lfu@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Luotao Fu <lfu@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
the needed infrastructure is already in place, only selecting
GENERIC_TIME was missing.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Add Nuvoton W90X900 ARM9 plat support to linux arm tree,
Now, this patch include only W90P910 EVB of W90P910 CPU,
Its driver is nothing.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the necessary definitions and Kconfig entries to enable
Cortex-A9 (ARMv7 SMP) tiles on the RealView/EB board.
Signed-off-by: Jon Callan <Jon.Callan@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
People often point to the Integrator/Versatile/Realview
implementations to justify using the consumer name as the sole
selector for clocks.
Eliminate this excuse by changing the Versatile implementation, so
it provides a better example of how it should be done.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
People often point to the Integrator/Versatile/Realview
implementations to justify using the consumer name as the sole
selector for clocks.
Eliminate this excuse by changing the Integrator implementation, so
it provides a better example of how it should be done.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
People often point to the Integrator/Versatile/Realview
implementations to justify using the consumer name as the sole
selector for clocks.
Eliminate this excuse by changing the Realview implementation, so
it provides a better example of how it should be done.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CLPS7500 platform has not built since 2.6.22-git7 and there
seems to be no interest in fixing it. So, remove the platform
support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than:
config CPU_BLAH
bool
depends on ARCH_FOO || MACH_BAR
default y if ARCH_FOO || MACH_BAR
arrange for ARCH_FOO and MACH_BAR to select CPU_BLAH directly.
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: Brian Swetland <swetland@google.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] pxa: corgi backlight driver should not select ssp drivers
[ARM] 5321/1: Kirkwood: fix typo in Makefile
[ARM] 5320/1: fix assembly constraints in implementation of do_div()
[ARM] 5318/1: Swap the PRRR and NMRR values in proc-v7.S
[ARM] 5316/1: AT91: oops (regression) fix on gpio irq
[ARM] msm: vreg interface to msm7k pmic
[ARM] msm: dma: various basic dma improvements and bugfixes
[ARM] msm: clock: provide clk_*() api support for
[ARM] msm: clean up iomap and devices
[ARM] msm: add proc_comm support, necessary for clock and power control
[ARM] msm: rename ARCH_MSM7X00A to ARCH_MSM
[ARM] pxa/spitz: fix unbalance parenthesis in header file spitz.h
[ARM] pxa: update {corgi,spitz}_defconfig to favor SPI-based drivers
[ARM] pxa: fix the corgi_ssp.c dependency issue in {corgi,spitz}_defconfig
Revert "[ARM] pxa/corgi: remove now unused corgi_ssp.c and corgi_lcd.c"
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb: (47 commits)
uwb: wrong sizeof argument in mac address compare
uwb: don't use printk_ratelimit() so often
uwb: use kcalloc where appropriate
uwb: use time_after() when purging stale beacons
uwb: add credits for the original developers of the UWB/WUSB/WLP subsystems
uwb: add entries in the MAINTAINERS file
uwb: depend on EXPERIMENTAL
wusb: wusb-cbaf (CBA driver) sysfs ABI simplification
uwb: document UWB and WUSB sysfs files
uwb: add symlinks in sysfs between radio controllers and PALs
uwb: dont tranmit identification IEs
uwb: i1480/GUWA100U: fix firmware download issues
uwb: i1480: remove MAC/PHY information checking function
uwb: add Intel i1480 HWA to the UWB RC quirk table
uwb: disable command/event filtering for D-Link DUB-1210
uwb: initialize the debug sub-system
uwb: Fix handling IEs with empty IE data in uwb_est_get_size()
wusb: fix bmRequestType for Abort RPipe request
wusb: fix error path for wusb_set_dev_addr()
wusb: add HWA host controller driver
...
The ftrace daemon is complex and can cause nasty races if something goes
wrong. Since it affects all of the kernel, this patch disables dynamic
ftrace from any arch that depends on the daemon. Until the archs are
ported over to the new MCOUNT_RECORD method, I am disabling dynamic
ftrace from them.
Note: I am leaving in the arch/<arch>/kernel/ftrace.c code alone since
that can be used when the arch is ported to MCOUNT_RECORD. To port
the arch to MCOUNT_RECORD, the scripts/recordmcount.pl needs to be
updated. I will make that easier to do for 2.6.29. For 28, we will keep
the archs disabled.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The MSM architecture covers a wider family of chips than just the MSM7X00A.
Move to a more generic name, in perparation for supporting the specific
SoC variants as sub-architectures (ARCH_MSM7X01A, ARCH_MSM722X, etc). This
gives us ARCH_MSM for the (many) common peripherals.
This also removes the unused/obsolete config item MSM7X00A_IDLE.
Signed-off-by: Brian Swetland <swetland@google.com>
Due to confusion between the ftrace infrastructure and the gcc profiling
tracer "ftrace", this patch renames the config options from FTRACE to
FUNCTION_TRACER. The other two names that are offspring from FTRACE
DYNAMIC_FTRACE and FTRACE_MCOUNT_RECORD will stay the same.
This patch was generated mostly by script, and partially by hand.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch implements a new freezer subsystem in the control groups
framework. It provides a way to stop and resume execution of all tasks in
a cgroup by writing in the cgroup filesystem.
The freezer subsystem in the container filesystem defines a file named
freezer.state. Writing "FROZEN" to the state file will freeze all tasks
in the cgroup. Subsequently writing "RUNNING" will unfreeze the tasks in
the cgroup. Reading will return the current state.
* Examples of usage :
# mkdir /containers/freezer
# mount -t cgroup -ofreezer freezer /containers
# mkdir /containers/0
# echo $some_pid > /containers/0/tasks
to get status of the freezer subsystem :
# cat /containers/0/freezer.state
RUNNING
to freeze all tasks in the container :
# echo FROZEN > /containers/0/freezer.state
# cat /containers/0/freezer.state
FREEZING
# cat /containers/0/freezer.state
FROZEN
to unfreeze all tasks in the container :
# echo RUNNING > /containers/0/freezer.state
# cat /containers/0/freezer.state
RUNNING
This is the basic mechanism which should do the right thing for user space
task in a simple scenario.
It's important to note that freezing can be incomplete. In that case we
return EBUSY. This means that some tasks in the cgroup are busy doing
something that prevents us from completely freezing the cgroup at this
time. After EBUSY, the cgroup will remain partially frozen -- reflected
by freezer.state reporting "FREEZING" when read. The state will remain
"FREEZING" until one of these things happens:
1) Userspace cancels the freezing operation by writing "RUNNING" to
the freezer.state file
2) Userspace retries the freezing operation by writing "FROZEN" to
the freezer.state file (writing "FREEZING" is not legal
and returns EIO)
3) The tasks that blocked the cgroup from entering the "FROZEN"
state disappear from the cgroup's set of tasks.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: export thaw_process]
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Tested-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rather than having everything that needs DMABOUNCE also select
ZONE_DMA, arrange for DMABOUNCE to select it instead. This is
far more sensible.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most ARM machines don't need a special "DMA" memory zone, and
when configured out, the kernel becomes a bit smaller:
| text data bss dec hex filename
|3826182 102384 111700 4040266 3da64a vmlinux
|3823593 101616 111700 4036909 3d992d vmlinux.nodmazone
This is because the system now has only one zone total which effect is
to optimize away many conditionals in page allocation paths.
So let's configure this zone only on machines that need split zones.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the old led support in arch/arm/mach-pxa/leds...
for TRIZEPS4 SOM. It is / will be replaced by generic
led driver drivers/leds/...
Signed-off-by: Jürgen Schindele <linux@schindele.name>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enable Sparsemem support for LH7A40x SoCs, while still allowing the
existing discontig support for the time being.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Orion-1-90 (88F6183) is another member of the Orion SoC family,
which has a 16 bit DDR2 interface, one x1 PCIe port (configurable as
Root Complex or Endpoint), one 10/100/1000 ethernet interface, one
USB 2.0 port with PHY, one SPDIF/I2S interface, one SDIO interface,
one TWSI interface, two UARTs, one SPI interface, a NAND controller,
a crypto engine, and a 4-channel DMA engine.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Switch DaVinci SOC gpios over to using the new GPIO library, so it can
access GPIO expanders and other non-SOC GPIOs using the same calls.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
HAVE_AOUT doesn't quite do the same thing as the recently removed
ARCH_SUPPORTS_AOUT config option. That was set even on platforms where
binfmt_aout isn't supported, although it's not entirely clear why.
So it's best just to introduce a new symbol, handled consistently with
other similar HAVE_xxx symbols; with a simple 'select' in the arch Kconfig.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a config option (CONFIG_VMSPLIT_*) to allow choosing
between 3:1, 2:2 and 1:3 user:kernel memory splits.
Tested-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add Oprofile kernel support for ARMv7.
Tested on OMAP3430 and OMAP3530 chipsets (Cortex-A8).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ordinarily, memory holes in flatmem still have a valid memmap and is safe
to use. However, an architecture (ARM) frees up the memmap backing memory
holes on the assumption it is never used. /proc/pagetypeinfo reads the
whole range of pages in a zone believing that the memmap is valid and that
pfn_valid will return false if it is not. On ARM, freeing the memmap breaks
the page->zone linkages even though pfn_valid() returns true and the kernel
can oops shortly afterwards due to accessing a bogus struct zone *.
This patch lets architectures say when FLATMEM can have holes in the
memmap. Rather than an expensive check for valid memory, /proc/pagetypeinfo
will confirm that the page linkages are still valid by checking page->zone
is still the expected zone. The lookup of page_zone is safe as there is a
limited range of memory that is accessed when calling page_zone. Even if
page_zone happens to return the correct zone, the impact is that the counters
in /proc/pagetypeinfo are slightly off but fragmentation monitoring is
unlikely to be relevant on an embedded system.
Reported-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds kernel build support for the regulator core.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (21 commits)
x86/PCI: use dev_printk when possible
PCI: add D3 power state avoidance quirk
PCI: fix bogus "'device' may be used uninitialized" warning in pci_slot
PCI: add an option to allow ASPM enabled forcibly
PCI: disable ASPM on pre-1.1 PCIe devices
PCI: disable ASPM per ACPI FADT setting
PCI MSI: Don't disable MSIs if the mask bit isn't supported
PCI: handle 64-bit resources better on 32-bit machines
PCI: rewrite PCI BAR reading code
PCI: document pci_target_state
PCI hotplug: fix typo in pcie hotplug output
x86 gart: replace to_pages macro with iommu_num_pages
x86, AMD IOMMU: replace to_pages macro with iommu_num_pages
iommu: add iommu_num_pages helper function
dma-coherent: add documentation to new interfaces
Cris: convert to using generic dma-coherent mem allocator
Sh: use generic per-device coherent dma allocator
ARM: support generic per-device coherent dma mem
Generic dma-coherent: fix DMA_MEMORY_EXCLUSIVE
x86: use generic per-device dma coherent allocator
...
This fixes a merge goof whereby ARCH_EP93XX got the "select HAVE_CLK" line
which belongs instead with ARCH_AT91.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
7444a72eff caused these platforms to lose
their GPIOLIB configuration. Convert the missed Kconfig symbols using:
sed -i s/HAVE_GPIO_LIB/ARCH_REQUIRE_GPIOLIB/ arch/arm/Kconfig arch/arm/plat-s3c24xx/Kconfig
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds functionality to the gpio-lib subsystem to make it
possible to enable the gpio-lib code even if the architecture code didn't
request to get it built in.
The archtitecture code does still need to implement the gpiolib accessor
functions in its asm/gpio.h file. This patch adds the implementations for
x86 and PPC.
With these changes it is possible to run generic GPIO expansion cards on
every architecture that implements the trivial wrapper functions. Support
for more architectures can easily be added.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Flag platforms as HAVE_CLK (or not) in Kconfig, based on whether they
support <linux/clk.h> calls, so that otherwise portable drivers which need
those calls can list that dependency.
Something like this is a prerequisite for merging the musb_hdrc driver,
currently used on platforms including Davinci, OMAP2430, OMAP3xx ... and
the discrete TUSB6010 chip, which doesn't have a natural platform
dependency. (Used with OMAP 2420 in current Nokia N8x0 tablets.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the ARCH=arm specific a kgdb backend, originally
written by Deepak Saxena <dsaxena@plexity.net> and George Davis
<gdavis@mvista.com>. Geoff Levand <geoffrey.levand@am.sony.com>,
Nicolas Pitre, Manish Lachwani, and Jason Wessel have contributed
various fixups here as well.
The KGDB patch makes one change to the core ARM architecture such that
the traps are initialized early for use with the debugger or other
subsystems.
[ mingo@elte.hu: small cleanups. ]
[ ben-linux@fluff.org: fixed early_trap_init ]
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Deepak Saxena <dsaxena@plexity.net>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
[ARM] 5171/1: ep93xx: fix compilation of modules using clocks
[ARM] 5133/2: at91sam9g20 defconfig file
[ARM] 5130/4: Support for the at91sam9g20
[ARM] 5160/1: IOP3XX: gpio/gpiolib support
[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
[ARM] 5084/1: zylonite: Register AC97 device
[ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
[ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
[ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
[ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
[ARM] 5144/1: pxaficp_ir: cleanup includes
[ARM] pxa: remove pxa_set_cken()
[ARM] pxa: allow clk aliases
[ARM] Feroceon: don't disable BPU on boot
[ARM] Orion: LED support for HP mv2120
[ARM] Orion: add RD88F5181L-FXO support
[ARM] Orion: add RD88F5181L-GE support
[ARM] Orion: add Netgear WNR854T support
[ARM] s3c2410_defconfig: update for current build
[ARM] Acer n30: Minor style and indentation fixes.
...
This includes PXA work up to the SPI changes for the initial merge,
since e172274ccc depends on the SPI
tree being merged.
Conflicts:
arch/arm/configs/em_x270_defconfig
arch/arm/configs/xm_x270_defconfig
This patch brings support for gpio/gpiolib framework to Intel IOP3xx
platforms.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds timer support for the i.MX machine family. This code can
be used on the following machs:
- i.MX1 (tested)
- i.MX2 (i.MX21 (to be tested), i.MX27 (tested))
- i.MX3 (i.MX31 (tested))
TODO: It seems impossible to build a kernel for more than one CPU because the
timer do not follow the platform device rules. So it does only work if
timer 1 can be accessed on all CPUs at the same address.
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch bases on the one from Daniel Mack. The most important change to
Daniel's patch is to be more generic. This gpio routine supports at least
the i.MX27 and i.MX31 processors.
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Acked-by: Daniel Mack <daniel@caiaq.de>
ARM architecture is not using __do_IRQ
Acked-By: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use HAVE_PATA_PLATFORM for ARCH_RPC
Cc: Linux ARM Kernel <linux-arm-kernel@lists.arm.linux.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This converts arm to use the new helpers for smp_call_function() and
friends, and adds support for smp_call_function_single().
Fixups and testing done by Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The Marvell Discovery Duo (MV78xx0) is a family of ARM SoCs featuring
(depending on the model) one or two Feroceon CPU cores with 512K of L2
cache and VFP coprocessors running at (depending on the model) between
800 MHz and 1.2 GHz, and features a DDR2 controller, two PCIe
interfaces that can each run either in x4 or quad x1 mode, three USB
2.0 interfaces, two 3Gb/s SATA II interfaces, a SPI interface, two
TWSI interfaces, a crypto accelerator, IDMA/XOR engines, a SPI
interface, four UARTs, and depending on the model, two or four gigabit
ethernet interfaces.
This patch adds basic support for the platform, and allows booting
on the MV78x00 development board, with functional UARTs, SATA, PCIe,
GigE and USB ports.
Signed-off-by: Stanislav Samsonov <samsonov@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The Marvell Kirkwood (88F6000) is a family of ARM SoCs based on a
Shiva CPU core, and features a DDR2 controller, a x1 PCIe interface,
a USB 2.0 interface, a SPI controller, a crypto accelerator, a TS
interface, and IDMA/XOR engines, and depending on the model, also
features one or two Gigabit Ethernet interfaces, two SATA II
interfaces, one or two TWSI interfaces, one or two UARTs, a
TDM/SLIC interface, a NAND controller, an I2S/SPDIF interface, and
an SDIO interface.
This patch adds supports for the Marvell DB-88F6281-BP Development
Board and the RD-88F6192-NAS and the RD-88F6281 Reference Designs,
enabling support for the PCIe interface, the USB interface, the
ethernet interfaces, the SATA interfaces, the TWSI interfaces, the
UARTs, and the NAND controller.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The Marvell Loki (88RC8480) is an ARM SoC based on a Feroceon CPU
core running at between 400 MHz and 1.0 GHz, and features a 64 bit
DDR controller, 512K of internal SRAM, two x4 PCI-Express ports,
two Gigabit Ethernet ports, two 4x SAS/SATA controllers, two UARTs,
two TWSI controllers, and IDMA/XOR engines.
This patch adds support for the Marvell LB88RC8480 Development
Board, enabling the use of the PCIe interfaces, the ethernet
interfaces, the TWSI interfaces and the UARTs.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Available for !SMP only at the moment.
From Russell:
|Basically, if a thread is running on a CPU, thread_saved_fp() is invalid.
|So, the question is: what guarantees do we have here that 'tsk' is not
|running on another CPU?
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Core ftrace support for the ARM architecture, which includes support
for dynamic function tracing.
Signed-off-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
dyntick is superseded by the clocksource/clockevent infrastructure,
using the NO_HZ configuration option. No one implements dyntick on
ARM anymore, so it's pointless keeping it around. Remove dyntick
support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Trying to compile a kerel for ARCH_CO285 fails with the following error:
<-- snip -->
...
CC arch/arm/mach-footbridge/dc21285.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:
In function 'dc21285_base_address':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:54: error: 'PCICFG0_BASE' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:54: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:54: error: for each function it appears in.)
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:57: error: 'PCICFG1_BASE' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:
In function 'dc21285_scan_bus':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:286: error: implicit declaration of function 'pci_scan_bus'
...
make[2]: *** [arch/arm/mach-footbridge/dc21285.o] Error 1
<-- snip -->
This does not seem to be a recent breakage.
The ARCH_CO285 support is old - kernel 2.2.0 contains first traces of
it, an it seems to have been pretty complete in later 2.2 kernels.
Since it seems to be completely dead code now this patch therefore
removes it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It's plain wrong for PCMCIA to select HAVE_IDE that implies e.g. the
availability of an asm/ide.h
It turns out this was done for ARM, and we can simply always select
HAVE_IDE on ARM instead of manually tracking which platforms might
possible have an IDE controller directly or indirectly.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
SCSI: convert struct class_device to struct device
DRM: remove unused dev_class
IB: rename "dev" to "srp_dev" in srp_host structure
IB: convert struct class_device to struct device
memstick: convert struct class_device to struct device
driver core: replace remaining __FUNCTION__ occurrences
sysfs: refill attribute buffer when reading from offset 0
PM: Remove destroy_suspended_device()
Firmware: add iSCSI iBFT Support
PM: Remove legacy PM (fix)
Kobject: Replace list_for_each() with list_for_each_entry().
SYSFS: Explicitly include required header file slab.h.
Driver core: make device_is_registered() work for class devices
PM: Convert wakeup flag accessors to inline functions
PM: Make wakeup flags available whenever CONFIG_PM is set
PM: Fix misuse of wakeup flag accessors in serial core
Driver core: Call device_pm_add() after bus_add_device() in device_add()
PM: Handle device registrations during suspend/resume
block: send disk "change" event for rescan_partitions()
sysdev: detect multiple driver registrations
...
Fixed trivial conflict in include/linux/memory.h due to semaphore header
file change (made irrelevant by the change to mutex).
Source drivers/uio/Kconfig to make UIO available in menuconfig if ARCH=arm.
Signed-off-by: Hans J Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support for the generic GPIO lib to the EP93xx family. The gpio
handling code has been moved from core.c to a new file called gpio.c.
The GPIO based IRQ code has not been changed.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the PB11MPCore support to the corresponding Kconfig
and Makefile to enable building.
Signed-off-by: Bahadir Balban <bahadir.balban@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
d142b6e77d added clock source support,
now it's time for the clock event support.
Tested-by: Thomas Kunze <thommycheck@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update OMAP to use the new GPIO implementation framework. This is just a
quick'n'dirty update ... more code could now be removed, ideally as part
of cleaning up the entire OMAP GPIO infrastructure ...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds gpiolib support for the SA-1100 arch:
- Move all GPIO API functions from generic.c into gpio.c
- Convert all gpio functions into gpiolib callbacks.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Do a global s/orion/orion5x/ of the Orion 5x-specific bits (i.e.
not the plat-orion bits.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Create arch/arm/plat-orion/, for peripherals shared between various
Marvell Orion SoCs.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
One-shot mode was broken in MPU-timer support for OMAP1 due to a typo.
Also, ensure timer is stopped before changing the auto-reload flag.
The TRM says changing the AR flag when timer is running is undefined.
Also set GENERIC_CLOCKEVENTS for all omaps.
Signed-off-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add CONFIG_HAVE_KRETPROBES to the arch/<arch>/Kconfig file for relevant
architectures with kprobes support. This facilitates easy handling of
in-kernel modules (like samples/kprobes/kretprobe_example.c) that depend on
kretprobes being present in the kernel.
Thanks to Sam Ravnborg for helping make the patch more lean.
Per Mathieu's suggestion, added CONFIG_KRETPROBES and fixed up dependencies.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Wed, Feb 20, 2008 at 11:50:33AM +0100, Guennadi Liakhovetski wrote:
> arch/arm/kernel/atags.c uses for some reason the
> KEXEC_BOOT_PARAMS_SIZE macro, which is only defined if CONFIG_KEXEC
> is set. So, either this macro should be defined always, or another
> macro should be used, or ATAGS_PROC should depend on KEXEC.
As the procfs export of ATAGS is not meant as a stable, general purpose
ABI it shouldn't be an independent, general configuration option.
This patch make ATAGS_PROC depend on KEXEC
Signed-off-by: Uli Luckas <u.luckas@road.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To allow flexible configuration of IDE introduce HAVE_IDE.
All archs except arm, um and s390 unconditionally select it.
For arm the actual configuration determine if IDE is supported.
This is a step towards introducing drivers/Kconfig for arm.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Mark arches that support A.OUT format by including the following in their
master Kconfig files:
config ARCH_SUPPORTS_AOUT
def_bool y
This should also be set if the arch provides compatibility A.OUT support for
an older arch, for instance x86_64 for i386 or sparc64 for sparc.
I've guessed at which arches don't, based on comments in the code, however I'm
sure that some of the ones I've marked as 'yes' actually should be 'no'.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds gpiolib support for the PXA architecture:
- move all GPIO API functions from generic.c into gpio.c
- convert the gpio_get/set_value macros into inline functions
This makes it easier to hook up GPIOs provided by external chips like
ASICs and CPLDs.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Minor ARM fixup from David Brownell folded into this ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an empty drivers/gpio directory for gpiolib infrastructure and GPIO
expanders. It will be populated by later patches.
This won't be the only place to hold such gpio_chip code. Many external chips
add a few GPIOs as secondary functionality (such as MFD drivers) and platform
code frequently needs to closely integrate GPIO and IRQ support.
This is placed *early* in the build/link sequence since it's common for other
drivers to depend on GPIOs to do their work, so they must be initialized early
in the device_initcall() sequence.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (44 commits)
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
...
* at91:
[ARM] 4802/1: Fix typo and remove vague comment
[ARM] 4660/3: at91: allow selecting UART for early kernel messages
[ARM] 4739/1: at91sam9263: make gpio bank C and D irqs work
* ixp:
[ARM] 4809/2: ixp4xx: Merge dsmg600-power.c into dsmg600-setup.c
[ARM] 4808/2: ixp4xx: Merge nas100d-power.c into nas100d-setup.c
[ARM] 4807/2: ixp4xx: Merge nslu2-power.c into nslu2-setup.c
[ARM] 4806/1: ixp4xx: Ethernet support for the nslu2 and nas100d boards
[ARM] 4805/1: ixp4xx: Use leds-gpio driver instead of IXP4XX-GPIO-LED driver
[ARM] 4715/2: Ethernet support for IXDP425 boards
[ARM] 4714/2: Headers for IXP4xx built-in Ethernet and WAN drivers
[ARM] 4713/3: Adds drivers for IXP4xx QMgr and NPE features
[ARM] 4712/2: Adds functions to read and write IXP4xx "feature" bits
[ARM] 4774/2: ixp4xx: Register dsmg600 rtc i2c_board_info
[ARM] 4773/2: ixp4xx: Register nas100d rtc i2c_board_info
[ARM] 4772/2: ixp4xx: Register nslu2 rtc i2c_board_info
[ARM] 4769/2: ixp4xx: Button updates for the dsmg600 board
[ARM] 4768/2: ixp4xx: Button and LED updates for the nas100d board
[ARM] 4767/2: ixp4xx: Add bitops.h include to io.h
[ARM] 4766/2: ixp4xx: Update ixp4xx_defconfig, enabling all supported boards
* master:
[ARM] 4810/1: - Fix 'section mismatch' building warnings
[ARM] xtime_seqlock: fix more ARM machines for xtime deadlocking
[ARM] 21285 serial: fix build error
* misc:
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
* pxa:
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
[ARM] pxa: fix the warning of undeclared "struct pxaohci_platform_data"
[ARM] pxa: change set_kset_name() to direct name assignment for MFP sysclass
* realview:
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
This patch changes the REALVIEW_MPCORE configuration option to
REALVIEW_EB_ARM11MP since this is only specific to RealView/EB.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds dummy local timers for each CPU so that the board clock
device is used to broadcast events to the other CPUs. The patch also
adds the declaration for the dummy_timer_setup function (the equivalent
of local_timer_setup when CONFIG_LOCAL_TIMERS is not set).
Due to the way clockevents work, the dummy timer on the first CPU has to
be registered before the board timer.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch updates the RealView code to the clockevents infrastructure.
The SMP support is implemented in subsequent patches. Based on the
Versatile implementation by Kevin Hilman.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch updates the RealView platform code to use the generic
clocksource infrastructure for basic time keeping. Based on the
Versatile implementation by Kevin Hilman.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, the atags used by kexec are fixed to the ones originally used
to boot the kernel. This is less than ideal as changing the commandline,
initrd and other options would be a useful feature.
This patch exports the atags used for the current kernel to userspace
through an "atags" file in procfs. The presence of the file is
controlled by its own Kconfig option and cleans up several ifdef blocks
into a separate file. The tags for the new kernel are assumed to be at
a fixed location before the kernel image itself. The location of the
tags used to boot the original kernel is unimportant and no longer
saved.
Based on a patch from Uli Luckas <u.luckas@road.de>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Uli Luckas <u.luckas@road.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After seeing the filename I'd have expected something about the
implementation of SMP in the Linux kernel - not some notes on kernel
configuration and building trivialities noone would search at this
place.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Linus:
On the per-architecture side, I do think it would be better to *not* have
internal architecture knowledge in a generic file, and as such a line like
depends on X86_32 || IA64 || PPC || S390 || SPARC64 || X86_64 || AVR32
really shouldn't exist in a file like kernel/Kconfig.instrumentation.
It would be much better to do
depends on ARCH_SUPPORTS_KPROBES
in that generic file, and then architectures that do support it would just
have a
bool ARCH_SUPPORTS_KPROBES
default y
in *their* architecture files. That would seem to be much more logical,
and is readable both for arch maintainers *and* for people who have no
clue - and don't care - about which architecture is supposed to support
which interface...
Changelog:
Actually, I know I gave this as the magic incantation, but now that I see
it, I realize that I should have told you to just use
config KPROBES_SUPPORT
def_bool y
instead, which is a bit denser.
We seem to use both kinds of syntax for these things, but this is really
what "def_bool" is there for...
- Use HAVE_KPROBES
- Use a select
- Yet another update :
Moving to HAVE_* now.
- Update ARM for kprobes support.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Linus:
On the per-architecture side, I do think it would be better to *not* have
internal architecture knowledge in a generic file, and as such a line like
depends on X86_32 || IA64 || PPC || S390 || SPARC64 || X86_64 || AVR32
really shouldn't exist in a file like kernel/Kconfig.instrumentation.
It would be much better to do
depends on ARCH_SUPPORTS_KPROBES
in that generic file, and then architectures that do support it would just
have a
bool ARCH_SUPPORTS_KPROBES
default y
in *their* architecture files. That would seem to be much more logical,
and is readable both for arch maintainers *and* for people who have no
clue - and don't care - about which architecture is supposed to support
which interface...
Changelog:
Actually, I know I gave this as the magic incantation, but now that I see
it, I realize that I should have told you to just use
config ARCH_SUPPORTS_KPROBES
def_bool y
instead, which is a bit denser.
We seem to use both kinds of syntax for these things, but this is really
what "def_bool" is there for...
Changelog :
- Moving to HAVE_*.
- Add AVR32 oprofile.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The conflicting commit for
move-kconfiginstrumentation-to-arch-kconfig-and-init-kconfig.patch
is the ARM fix from Linus :
commit 38ad9aebe7
He just seemed to agree that my approach (just putting the missing ARM
config options in arch/arm/Kconfig) works too. The main advantage it has
is that it is smaller, does not need a cleanup in the future and does
not break the following patches unnecessarily.
It's just been discussed here
http://lkml.org/lkml/2008/1/15/267
However, Linus might prefer to stay with his own patch and I would
totally understand it that late in the release cycle. Therefore I submit
this for the next release cycle.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
CC: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* 'suspend' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (38 commits)
suspend: cleanup reference to swsusp_pg_dir[]
PM: Remove obsolete /sys/devices/.../power/state docs
Hibernation: Invoke suspend notifications after console switch
Suspend: Invoke suspend notifications after console switch
Suspend: Clean up suspend_64.c
Suspend: Add config option to disable the freezer if architecture wants that
ACPI: Print message before calling _PTS
ACPI hibernation: Call _PTS before suspending devices
Hibernation: Introduce begin() and end() callbacks
ACPI suspend: Call _PTS before suspending devices
ACPI: Separate disabling of GPEs from _PTS
ACPI: Separate invocations of _GTS and _BFS from _PTS and _WAK
Suspend: Introduce begin() and end() callbacks
suspend: fix ia64 allmodconfig build
ACPI: clear GPE earily in resume to avoid warning
Suspend: Clean up Kconfig (V2)
Hibernation: Clean up Kconfig (V2)
Hibernation: Update messages
Suspend: Use common prefix in messages
Hibernation: Remove unnecessary variable declaration
...
This cleans up the suspend Kconfig and removes the need to
declare centrally which architectures support suspend. All
architectures that currently support suspend are modified
accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
A HOWTO that hasn't been updated for half a dozen years no longer
"contains valuable information about which PCI hardware does work under
Linux and which doesn't".
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The break_lock data structure and code for spinlocks is quite nasty.
Not only does it double the size of a spinlock but it changes locking to
a potentially less optimal trylock.
Put all of that under CONFIG_GENERIC_LOCKBREAK, and introduce a
__raw_spin_is_contended that uses the lock data itself to determine whether
there are waiters on the lock, to be used if CONFIG_GENERIC_LOCKBREAK is
not set.
Rename need_lockbreak to spin_needbreak, make it use spin_is_contended to
decouple it from the spinlock implementation, and make it typesafe (rwlocks
do not have any need_lockbreak sites -- why do they even get bloated up
with that break_lock then?).
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* orion: (26 commits)
[ARM] Orion: implement power-off method for QNAP TS-109/209
[ARM] Orion: add support for QNAP TS-109/TS-209
[ARM] Orion: I2C support
[I2C] i2c-mv64xxx: Don't set i2c_adapter.retries
[I2C] Split mv643xx I2C platform support
[ARM] Orion: enable CONFIG_RTC_DRV_M41T80 for D-Link DNS-323
[ARM] Orion defconfig
[ARM] Orion: add support for Orion/MV88F5181 based D-Link DNS-323
[ARM] Orion: MV88F5181 support bits
[ARM] Orion: Buffalo/Revogear Kurobox Pro support
[ARM] OrionNAS RD board support
[ARM] Orion: support for Marvell Orion-2 (88F5281) Development Board
[ARM] Orion: common platform setup for Gigabit Ethernet port
[ARM] Orion: platform device registration for UART, USB and NAND
[ARM] Orion: system timer support
[ARM] Orion edge GPIO IRQ support
[ARM] Orion: IRQ support
[ARM] Orion: provide GPIO method for enabling hardware assisted blinking
[ARM] Orion: GPIO support
[ARM] Orion: programable address map support
...
Conflicts:
arch/arm/Kconfig
arch/arm/Makefile
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There have been patches hanging around for ages to add support for
cpufreq to PXA255 processors. It's about time we applied one.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Apparantly, the generic time subsystem can accurately emulate periodic
mode via the one-shot support code, so we don't need our own periodic
emulation code anymore. Just ensure that we build support for one shot
into the generic time subsystem.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
serial, NOR, PCI and Ethernet is activated at the moment.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for PCI and PCI-E controllers in the
Orion, Orion-NAS and Orion2.
Signed-off-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Marvell Orion is a family of ARM SoCs with a DDR/DDR2 memory
controller, 10/100/1000 ethernet MAC, and USB 2.0 interfaces,
and, depending on the specific model, PCI-E interface, PCI-X
interface, SATA controllers, crypto unit, SPI interface, SDIO
interface, device bus, NAND controller, DMA engine and/or XOR
engine.
This contains the basic structure and architecture register definitions.
Signed-off-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Feroceon is a family of independent ARMv5TE compliant CPU core
implementations, supporting a variable depth pipeline and out-of-order
execution. The Feroceon is configurable with VFP support, and the
later models in the series are superscalar with up to two instructions
per clock cycle.
This patch adds the initial low-level cache/TLB handling for this core.
Signed-off-by: Assaf Hoffman <hoffman@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for Atmel's AT91CAP9 Customizable Microcontroller family.
<http://www.atmel.com/products/AT91CAP/Default.asp>
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This makes HZ configurable on AT91, following the model used on OMAP.
It defaults to a power of two on AT91rm9200 chips, avoiding rounding
errors which come from dividing a 32 KiHz clock to generate scheduler
irqs; and uses 100 on AT91sam926x chips, using MCK/16 (multi-MHZ).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Remy Bhmer <linux@bohmer.net>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch enables the use of the Advanced SIMD (NEON) extension on
ARMv7. The NEON technology is a 64/128-bit hybrid SIMD architecture
for accelerating the performance of multimedia and signal processing
applications. The extension shares the registers with the VFP unit and
enabling/disabling and saving/restoring follow the same rules. In
addition, there are instructions that do not have the appropriate CP
number encoded, the checks being made in the call_fpe function.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the support for VFPv3 (the kernel currently supports
VFPv2). The main difference is 32 double registers (compared to 16).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Qualcomm MSM7200A eval board.
Common devices are defined in common.c, to avoid excessive
cut'n'pasting them into other board files.
Signed-off-by: Brian Swetland <swetland@google.com>
- core header files for arch-msm
- Kconfig and Makefiles to enable ARCH_MSM7X00A builds
- MSM7X00A specific arch_idle
- peripheral iomap and irq number definitions
Signed-off-by: Brian Swetland <swetland@google.com>
Implement new GPIO API for ep93xx platform as defined in Documentation/gpio.txt
and provide transitional __deprecated wrappers for the previous gpio_line_*
functions.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
'select' used by config symbol 'INTEL_IOATDMA' refers to undefined symbol 'DCA'
Although drivers/dma is currently the only user future drivers outside of
drivers/dma may select this option so it is better to add this to
arch/arm/Kconfig than move DCA to drivers/dma/Kconfig.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 09cadedbdc ("Combine
instrumentation menus in kernel/Kconfig.instrumentation") broke ARM
profiling support, since ARM has some extra Kconfig options and doesn't
just use the common OPROFILE/KPROBES config options.
Rather than just revert the thing outright, or add ARM-specific
knowledge to the generic Kconfig.instrumentation file (where the only
and whole point was to be generic, not too architecture-specific), this
just makes ARM not use the generic version, since it doesn't suit it.
So create an arm-specific version of Kconfig.instrumentation instead,
and use that.
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change printk to dev_dbg in ITE 8152 driver and remove printk in ITE 8152 ISR.
Move PCI intialization from ->scan to ->preinit method
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most of these fixes were already submitted for old kernel versions, and were
approved, but for some reason they never made it into the releases.
Because this is a consolidation of a couple old missed patches, it touches both
Kconfigs and documentation texts.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Quoting Randy:
"It seems sad that this patch sources Kconfig.marker, a 7-line file,
20-something times. Yes, you (we) don't want to put those 7 lines into
20-something different files, so sourcing is the right thing.
However, what you did for avr32 seems more on the right track to me: make
_one_ Instrumentation support menu that includes PROFILING, OPROFILE, KPROBES,
and MARKERS and then use (source) that in all of the arches."
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This implementation conforms to the general GPIO API
introduced in 2.6.21.
This patch was signed-of by David Brownell before I exported the functions
using EXPORT_SYMBOL.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Bugfixes for the OSK led support:
- Fix Kconfig merge glitches: Mistral handles idle and timer leds just fine
- Fix pm_suspend() runtime botch: can't sleep, so can't touch tps65010 leds
Improvements:
- Switch sense of Mistral idle led, so idle == off
Probably the TPS65010 leds should be handled only by the "new led" API.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
make ARCH_PXA select GENERIC_CLOCKEVENTS to fix the
building issue due to merge of clockevents based PXA
timer
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Create the initial arch/arm/plat-s3c directory and start
linking it into the arch/arm build heirarchy ready to
receive the generic parts of the S3C24XX support to be
used when adding S3C6400 devices.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the foundation pieces for
the Freescale MXC platforms, including
i.MX2 and i.MX3 based systems.
The bare-bones MX31 support in this patch
boots to the rootdev panic with 8250 serial
console configured "console=ttyS0,115200".
It assumes that Redboot is the boot loader.
Signed-off-by: Quinn Jensen <quinn.jensen@freescale.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'ioat-md-accel-for-linus' of git://lost.foo-projects.org/~dwillia2/git/iop: (28 commits)
ioatdma: add the unisys "i/oat" pci vendor/device id
ARM: Add drivers/dma to arch/arm/Kconfig
iop3xx: surface the iop3xx DMA and AAU units to the iop-adma driver
iop13xx: surface the iop13xx adma units to the iop-adma driver
dmaengine: driver for the iop32x, iop33x, and iop13xx raid engines
md: remove raid5 compute_block and compute_parity5
md: handle_stripe5 - request io processing in raid5_run_ops
md: handle_stripe5 - add request/completion logic for async expand ops
md: handle_stripe5 - add request/completion logic for async read ops
md: handle_stripe5 - add request/completion logic for async check ops
md: handle_stripe5 - add request/completion logic for async compute ops
md: handle_stripe5 - add request/completion logic for async write ops
md: common infrastructure for running operations with raid5_run_ops
md: raid5_run_ops - run stripe operations outside sh->lock
raid5: replace custom debug PRINTKs with standard pr_debug
raid5: refactor handle_stripe5 and handle_stripe6 (v3)
async_tx: add the async_tx api
xor: make 'xor_blocks' a library routine for use with async_tx
dmaengine: make clients responsible for managing channels
dmaengine: refactor dmaengine around dma_async_tx_descriptor
...
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (50 commits)
[ARM] sa1100: remove boot time RTC initialisation
[ARM] sa1100: stop doing our own rtc management over suspend
[ARM] 4474/1: Do not check the PSR_F_BIT in valid_user_regs
[ARM] 4473/2: Take the HWCAP definitions out of the elf.h file
[ARM] pxa: move platform devices to separate header file
[ARM] pxa: move device registration into CPU-specific file
[ARM] pxa: remove boot time RTC initialisation
[ARM] pxa: stop doing our own rtc management over suspend
[ARM] 4451/1: pxa: make dma.c generic and remove cpu specific dma code
[ARM] 4450/1: pxa: add pxa25x_init_irq() and pxa27x_init_irq()
[ARM] 4440/1: PXA: enable the checking of ICIP2 for IRQs
[ARM] 4438/1: PXA: remove #ifdef .. #endif from pxa_gpio_demux_handler()
[ARM] 4437/1: PXA: move the GPIO IRQ initialization code to pxa_init_irq_gpio()
[ARM] 4436/1: PXA: move low IRQ initialization code to pxa_init_irq_low()
[ARM] 4435/1: PXA: remove PXA_INTERNAL_IRQS
[ARM] 4434/1: PXA: remove PXA_IRQ_SKIP
[ARM] pxa: Fix PXA27x suspend type validation, remove pxa_pm_prepare()
[ARM] pxa: move pm_ops structure into CPU specific files
[ARM] pxa: introduce cpu_is_pxaXXX macros
[ARM] pxa: remove MMC register defines from pxa-regs.h
...
Driver to control the GPIO pins on the KS8695 processor.
The driver natively supports the Generic GPIO interface.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support clock event source based on i.MX general purpose
timer in free running timer mode.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for generic input output for MX1 family.
The implementation prevents allocation of one pin
by two users, but does not store pointer to the user
description permanently, because this solution
would have bigger memory overhead.
The simple way to integrate code with per BSP
pins setup and allocation is required else all GPIO
registration checking is useless. The function
imx_gpio_setup_multiple_pins() can be used for this
purpose in future.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support GPIO driver for TI DaVinci SoC
Signed-off-by: Vladimir Barinov <vbarino@ru.mvista.com>
Acked-by: David Brownell <david-b@pacbell.net>
Acked-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PCI syscalls are built on every architecture except X86, but only
a few have ever hooked them up. Use a new Kconfig symbol to save a
couple of kB on the architectures that have never used the syscalls.
Tested on x86 and ia64 only.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Selects GENERIC_GPIO for ARCH_IXP4XX in Kconfig.
IXP4XX has generic GPIO support; however, ARCH_IXP4XX
Kconfig entry currently does not select GENERIC_GPIO like other
arch entries.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add core support for the Kendin/Micrel KS8695 processor family.
It is an ARM922-T based SoC with integrated USART, 4-port Ethernet
Switch, WAN Ethernet port, and optional PCI Host bridge, etc.
http://www.micrel.com/page.do?page=product-info/sys_on_chip.jsp
This patch is based on earlier patches from Lennert Buytenhek, Ben
Dooks and Greg Ungerer posted to the arm-linux-kernel mailing list in
March 2006; and Micrel's 2.6.9 port.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the apparently useless config option GENERIC_BUST_SPINLOCK,
since nothing in the source tree refers to it.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add base kernel support for the TI DaVinci platform.
This patch only includes interrupts, timers, CPU identification,
serial support and basic power and sleep controller init. More
drivers to come.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Trying to build current git tree fails. The failure is due to commit
25ff0a6530. The patch title say it's for
OMAP board while it's applied on S3C2410 Kconfig entry. Moreover, the
OMAP entry is already selecting GENERIC_TIME.
This patch reverts the offending commit.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Somehow this got lost in a merge ...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allows architectures to advertise that they support MSI rather than listing
each architecture as a PCI_MSI dependency.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for stacktrace. Use the new stacktrace code with
oprofile instead of it's version; there's no point having
multiple versions of stacktracing in the kernel.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update OMAP1 to enable support for hrtimers and dynticks by using new clocksource and clockevent infrastructure.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update Versatile platform to use new clockevent infrastructure.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update Versatile to use new clocksource infrastructure for basic timekeeping.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update ixp4xx timer support to use new clockevent infrastructure.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This time with LEDS_TIMER set with !GENERIC_CLOCKEVENTS
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most drivers using GPIOs already know they are running on a system that
supports the generic GPIO calls, because of other platform dependencies.
But the generic GPIO-based LED and input button drivers can't know that.
So this patch adds a Kconfig hook, GENERIC_GPIO, to mark the platforms
where <asm/gpio.h> will do the right thing. Currently that's a bunch of
ARMs, and AVR32; more are on the way.
It also fixes a dependency bug for the gpio button input driver; it was
wrong to start with, now it covers all platforms with GENERIC_GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: <raph@8d.com>
Cc: <msvoboda@ra.rockwell.com>
Cc: pHilipp Zabel <philipp.zabel@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Work around EBSA110 build errors by selecting NO_IOPORT. EBSA110
can't support an IO port to MMIO mapping mechanism because the
MMIO and IO port spaces have quite different and complex addressing
requirements.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
Documentation/kernel-docs.txt update.
arch/cris: typo in KERN_INFO
Storage class should be before const qualifier
kernel/printk.c: comment fix
update I/O sched Kconfig help texts - CFQ is now default, not AS.
Remove duplicate listing of Cris arch from README
kbuild: more doc. cleanups
doc: make doc. for maxcpus= more visible
drivers/net/eexpress.c: remove duplicate comment
add a help text for BLK_DEV_GENERIC
correct a dead URL in the IP_MULTICAST help text
fix the BAYCOM_SER_HDX help text
fix SCSI_SCAN_ASYNC help text
trivial documentation patch for platform.txt
Fix typos concerning hierarchy
Fix comment typo "spin_lock_irqrestore".
Fix misspellings of "agressive".
drivers/scsi/a100u2w.c: trivial typo patch
Correct trivial typo in log2.h.
Remove useless FIND_FIRST_BIT() macro from cardbus.c.
...
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (117 commits)
[ARM] 4058/2: iop32x: set ->broken_parity_status on n2100 onboard r8169 ports
[ARM] 4140/1: AACI stability add ac97 timeout and retries
[ARM] 4139/1: AACI record support
[ARM] 4138/1: AACI: multiple channel support for IRQ handling
[ARM] 4211/1: Provide a defconfig for ns9xxx
[ARM] 4210/1: base for new machine type "NetSilicon NS9360"
[ARM] 4222/1: S3C2443: Remove reference to missing S3C2443_PM
[ARM] 4221/1: S3C2443: DMA support
[ARM] 4220/1: S3C24XX: DMA system initialised from sysdev
[ARM] 4219/1: S3C2443: DMA source definitions
[ARM] 4218/1: S3C2412: fix CONFIG_CPU_S3C2412_ONLY wrt to S3C2443
[ARM] 4217/1: S3C24XX: remove the dma channel show at startup
[ARM] 4090/2: avoid clash between PXA and SA1111 defines
[ARM] 4216/1: add .gitignore entries for ARM specific files
[ARM] 4214/2: S3C2410: Add Armzone QT2410
[ARM] 4215/1: s3c2410 usb device: per-platform vbus_draw
[ARM] 4213/1: S3C2410 - Update definition of ADCTSC_XY_PST
[ARM] 4098/1: ARM: rtc_lock only used with rtc_cmos
[ARM] 4137/1: Add kexec support
[ARM] 4201/1: SMP barriers pair needed for the secondary boot process
...
Fix up conflict due to typedef removal in sound/arm/aaci.h
Replace the very few remaining "depends" Kconfig directives with
"depends on".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Add kexec support to ARM.
Improvements like commandline handling could be made but this patch gives
basic functional support. It uses the next available syscall number, 347.
Once the syscall number is known, userspace support will be
finalised/submitted to kexec-tools, various patches already exist.
Originally based on a patch by Maxim Syrchin but updated and forward
ported by various people.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add arch/arm/mach-s3c2443 for support of the Samsung S3C2443 SoC
This patch adds the core CPU support, clock framework, times
and initial IRQ support, as well as adding the directory into
the build tree.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enable svc access to cp6 via an undefined instruction hook. Do not enable
access for usr code.
This patch also makes iop13xx select PLAT_IOP, this requires a small change
to drivers/i2c/busses/i2c-iop3xx.c.
Per Lennert Buytenhek's note, the cp6 trap routine is moved to arch/arm/plat-iop
Per Nicolas Pitre's note, the cp_wait is skipped since the latency to
return to the faulting function is longer than cp_wait.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* Split the implementation-agnostic stuff in separate files.
* Make sure that targets using non-default request_irq() pull
kernel/irq/devres.o
* Introduce new symbols (HAS_IOPORT and HAS_IOMEM) defaulting to positive;
allow architectures to turn them off (we needed these symbols anyway for
dependencies of quite a few drivers).
* protect the ioport-related parts of lib/devres.o with CONFIG_HAS_IOPORT.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As Andi pointed out: CONFIG_GENERIC_ISA_DMA only disables the ISA DMA
channel management. Other functionality may still expect GFP_DMA to
provide memory below 16M. So we need to make sure that CONFIG_ZONE_DMA is
set independent of CONFIG_GENERIC_ISA_DMA. Undo the modifications to
mm/Kconfig where we made ZONE_DMA dependent on GENERIC_ISA_DMA and set
theses explicitly in each arches Kconfig.
Reviews must occur for each arch in order to determine if ZONE_DMA can be
switched off. It can only be switched off if we know that all devices
supported by a platform are capable of performing DMA transfers to all of
memory (Some arches already support this: uml, avr32, sh sh64, parisc and
IA64/Altix).
In order to switch ZONE_DMA off conditionally, one would have to establish
a scheme by which one can assure that no drivers are enabled that are only
capable of doing I/O to a part of memory, or one needs to provide an
alternate means of performing an allocation from a specific range of memory
(like provided by alloc_pages_range()) and insure that all drivers use that
call. In that case the arches alloc_dma_coherent() may need to be modified
to call alloc_pages_range() instead of relying on GFP_DMA.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following patch and script moves the arch/arm/mach-s3c2410
directory into arch/arm/plat-s3c24xx for the generic core code
and inti arch/arm/mach-s3c{cpu} for the cpu/machine support files
Include directory include/asm-arm/plat-s3c24xx is added for the
core include files.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.
The following git commands should be run BEFORE applying this patch:
git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support to change MX1 CPU frequency at runtime.
Tested on PiKRON's PiMX1 board and seems to be fully
stable up to 200 MHz end even as low as 8 MHz.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
HID drivers are in their own directory now, so we have to
include the Kconfig file for arm.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This facility provides three entry points:
ilog2() Log base 2 of unsigned long
ilog2_u32() Log base 2 of u32
ilog2_u64() Log base 2 of u64
These facilities can either be used inside functions on dynamic data:
int do_something(long q)
{
...;
y = ilog2(x)
...;
}
Or can be used to statically initialise global variables with constant values:
unsigned n = ilog2(27);
When performing static initialisation, the compiler will report "error:
initializer element is not constant" if asked to take a log of zero or of
something not reducible to a constant. They treat negative numbers as
unsigned.
When not dealing with a constant, they fall back to using fls() which permits
them to use arch-specific log calculation instructions - such as BSR on
x86/x86_64 or SCAN on FRV - if available.
[akpm@osdl.org: MMC fix]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Howells <dhowells@redhat.com>
Cc: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Merge:
Atmel AT91RM9200 and AT91SAM9260 changes
General ARM developments
Disconfiguous memory cleanups
64-bit/32-bit division and sched_clock extension patches
EP93xx support changes
IOP support changes
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The iop348 processor integrates an Xscale (XSC3 512KB L2 Cache) core with a
Serial Attached SCSI (SAS) controller, multi-ported DDR2 memory
controller, 3 Application Direct Memory Access (DMA) controllers, a 133Mhz
PCI-X interface, a x8 PCI-Express interface, and other peripherals to form
a system-on-a-chip RAID subsystem engine.
The iop342 processor replaces the SAS controller with a second Xscale core
for dual core embedded applications.
The iop341 processor is the single core version of iop342.
This patch supports the two Intel customer reference platforms iq81340mc
for external storage and iq81340sc for direct attach (HBA) development.
The developer's manual is available here:
ftp://download.intel.com/design/iio/docs/31503701.pdf
Changelog:
* removed virtual addresses from resource definitions
* cleaned up some unnecessary #include's
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
XScale cores either have a DSP coprocessor (which contains a single
40 bit accumulator register), or an iWMMXt coprocessor (which contains
eight 64 bit registers.)
Because of the small amount of state in the DSP coprocessor, access to
the DSP coprocessor (CP0) is always enabled, and DSP context switching
is done unconditionally on every task switch. Access to the iWMMXt
coprocessor (CP0/CP1) is enabled only when an iWMMXt instruction is
first issued, and iWMMXt context switching is done lazily.
CONFIG_IWMMXT is supposed to mean 'the cpu we will be running on will
have iWMMXt support', but boards are supposed to select this config
symbol by hand, and at least one pxa27x board doesn't get this right,
so on that board, proc-xscale.S will incorrectly assume that we have a
DSP coprocessor, enable CP0 on boot, and we will then only save the
first iWMMXt register (wR0) on context switches, which is Bad.
This patch redefines CONFIG_IWMMXT as 'the cpu we will be running on
might have iWMMXt support, and we will enable iWMMXt context switching
if it does.' This means that with this patch, running a CONFIG_IWMMXT=n
kernel on an iWMMXt-capable CPU will no longer potentially corrupt iWMMXt
state over context switches, and running a CONFIG_IWMMXT=y kernel on a
non-iWMMXt capable CPU will still do DSP context save/restore.
These changes should make iWMMXt work on PXA3xx, and as a side effect,
enable proper acc0 save/restore on non-iWMMXt capable xsc3 cores such
as IOP13xx and IXP23xx (which will not have CONFIG_CPU_XSCALE defined),
as well as setting and using HWCAP_IWMMXT properly.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A number of configuration file changes.
These are mainly to replace references to ARCH_AT91RM9200 and
ARCH_AT91SAM9261 with the common/generic ARCH_AT91. That way we don't
need to mention every specific AT91 processor explicitly.
Also adds the configuration option for AT91SAM9260-EK and AT91SAM9261-EK
boards.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM doesn't source drivers/Kconfig like most architectures do, so the
newly added drivers/ata is currently not made available on ARM. SATA
is used on some ARM machines, like the Thecus N2100, so we need to
source drivers/ata/Kconfig.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Randy brought it to my attention that in proper english "can not" should always
be written "cannot". I donot see any reason to argue, even if I mightnot
understand why this rule exists. This patch fixes "can not" in several
Documentation files as well as three Kconfigs.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Enables the ixp4xx platforms to use Generic time-of-day.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds Generic time-of-day support for the ARM architecture.
The support is currently added using #ifdef's so that it can support
sub-arches that do not (yet) have a clocksource added. As sub-arches
add clocksource support, they should 'select GENERIC_TIME'
Signed-off-by: Deepak Saxena <dsaxena@mvista.com>
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In nommu mode, the exception vector location depends on the platforms.
Some of the implementations may have some special exception control
forwarding method in their ROM/flash and for some of them has its own
re-mapping mechanism by the h/w.
This patch introduces a special configuration CONFIG_CPU_HIGH_VECTOR which
turns on the CR_V bit in nommu mode. The CR_V bit is turned off by default.
This feature depends on CP15 and does not supported by ARM740.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All the current CP15 access codes in ARM arch can be categorized and
conditioned by the defines as follows:
Related operation Safe condition
a. any CP15 access !CPU_CP15
b. alignment trap CPU_CP15_MMU
c. D-cache(C-bit) CPU_CP15
d. I-cache CPU_CP15 && !( CPU_ARM610 || CPU_ARM710 ||
CPU_ARM720 || CPU_ARM740 ||
CPU_XSCALE || CPU_XSC3 )
e. alternate vector CPU_CP15 && !CPU_ARM740
f. TTB CPU_CP15_MMU
g. Domain CPU_CP15_MMU
h. FSR/FAR CPU_CP15_MMU
For example, alternate vector is supported if and only if
"CPU_CP15 && !CPU_ARM740" is satisfied.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The documentation for the ZBOOT_ROM_BSS config option describes it as
"The base address of 64KiB of read/write memory in the target for the
ROM-able zImage..." In actuality, it requires more than 100 KiB of
space in addition to enough space to hold the decompressed kernel.
This patch fixes the description in the Kconfig file.
Signed-off-by: Dan Fandrich <dfandrich@intrinsyc.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce the arch/arm/plat-iop directory, for code shared between the
iop32x and iop33x, and move the common memory map setup bits there.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Split the iop3xx mach type into iop32x and iop33x -- split the config
symbols, and move the code in the mach-iop3xx directory to the mach-iop32x
and mach-iop33x directories.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Switch the ARM irq core handling to the generic implementation. The
ARM specific header files now contain mostly migration stubs and
helper macros. Note that each machine type must be converted after
this step seperately. This was seperated out from the patch for easier
review.
The main changes for the machine type code is the conversion of the
type handlers to a 'type flow' and 'chip' model. This affects only the
multiplex interrupt handlers. A conversion macro needs to be added to
those implementations, which defines the data structure which is
registered by the set_irq_chained_handler() macro.
Some minor fixups of include files and the conversion of data
structure access is necessary all over the place.
The mostly macro based conversion was provided to allow an easy
migration of the existing implementations.
The code compiles on all defconfigs available in arch/arm/configs
except those which were broken also before applying the conversion
patches.
The code has been boot and runtime tested on most ARM platforms. The
results of an extensive testing and bugfixing series can be found
at: http://www.linutronix.de/index.php?page=testing
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Jrgen Schindele
This patch adds support for Trizeps4 SoM and ConXS-evalboard
from "Keith und Koep" This DIMM-module is based on PXA270.
Signed-off-by: Jrgen Schindele <linux@schindele.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This prepares the way for adding support for the new Atmel AT91SAM926x
processors.
Major changes:
- Rename time.c to at91rm9200_time.c
- Rename common.c to at91rm9200.c
- Introduce ARCH_AT91, of which ARCH_AT91RM9200, ARCH_AT91SAM9260 and
ARCH_AT91SAM9261 are dependent.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hyok says Intel Xscale is not currently supported by uCLinux.
Rather than adding #error statements to the Xscale support files
and causing !MMU+Xscale configurations to fail to build, prevent
Xscale-based machines from being selected in !MMU mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Include Kconfig-nommu when MMU is not selected.
(This is part of a patch from Hyok.)
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add the rest of the supported S3C24XX family to the
configuration selection for ARCH_S3C2410. This should
try and make it clearer for people trying to find the
S3C2440 or freinds where they can be found.--
Signed-off-by: Ben Dooks <ben-linux@fluff.org>Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Milan Svoboda
IXP4XX platform can happily live without pci bus. This patch modifies
Kconfig to support this option and modifies Makefile so pci only files
are compiled only when pci is really selected.
Patch is tested and ixdp465 runs fine with or without the pci bus.--
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>Signed-off-by: Deepak Saxena <dsaxena@plexity.net>Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch makes soft reboot work on the Versatile board. Thanks to
Catalin Marinas @ ARM for pointing out the proper way to do this.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch adds the base support for Hilscher's netX network
processors.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vitaly Wool
This patch adds basic chip support for PNX4008 ARM platform.
It's basically the same as the previous one, but with the rmk's
comments taken into account.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Dmitry Pervushin <dpervushin@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch allows for the addition of IXP4xx systems that do not make
use of the PCI interface by moving the CONFIG_PCI symbol selection to
be platform-specific instead of for all of IXP4xx. If at least one machine
with PCI support is built, the PCI code will be compiled in, but when
building !PCI, this will drastically shrink the kernel size.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Current implementations define NODES_SHIFT in include/asm-xxx/numnodes.h for
each arch. Its definition is sometimes configurable. Indeed, ia64 defines 5
NODES_SHIFT values in the current git tree. But it looks a bit messy.
SGI-SN2(ia64) system requires 1024 nodes, and the number of nodes already has
been changeable by config. Suitable node's number may be changed in the
future even if it is other architecture. So, I wrote configurable node's
number.
This patch set defines just default value for each arch which needs multi
nodes except ia64. But, it is easy to change to configurable if necessary.
On ia64 the number of nodes can be already configured in generic ia64 and SN2
config. But, NODES_SHIFT is defined for DIG64 and HP'S machine too. So, I
changed it so that all platforms can be configured via CONFIG_NODES_SHIFT. It
would be simpler.
See also: http://marc.theaimsgroup.com/?l=linux-kernel&m=114358010523896&w=2
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3424/2: ixp23xx: fix uncompress.h for recent CRLF decompressor change
[ARM] 3434/1: pxa i2s amsl define
[ARM] 3425/1: xsc3: need to include pgtable-hwdef.h
[ARM] Allow un-muxed syscalls to be available for everyone
[ARM] 3420/1: Missing clobber in example code
[ARM] nommu: fixups for the exception vectors
[ARM] nommu: add nommu specific Kconfig and MMUEXT variable in Makefile
[ARM] nommu: start-up code
[ARM] nommu: MPU support in boot/compressed/head.S
Add the foundations of a new LEDs subsystem. This patch adds a class which
presents LED devices within sysfs and allows their brightness to be
controlled.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Lennert Buytenhek
This patch adds support for the Intel ixp23xx series of CPUs. The
ixp23xx is an XSC3 based CPU with 512K of L2 cache, a 64bit 66MHz PCI
interface, two DDR RAM interfaces, QDR RAM interfaces, two gigabit
MACs, two 10/100 MACs, expansion bus, four microengines, a Media and
Switch Fabric unit almost identical to the one on the ixp2400, two
xscale (8250ish) UARTs and a bunch of other stuff.
This patch adds the core ixp23xx support code, and support for the
ADI Engineering Roadrunner, Intel IXDP2351, and IP Fabrics Double
Espresso platforms.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes from the ARM subsytem some of the rtc-related functions
that have been included in the RTC subsystem. It also fixes some naming
collisions.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The high page vector (0xFFFF0000) does not supported in nommu mode.
This patch allows the vectors to be 0x00000000 or the begining of DRAM
in nommu mode.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds support for the Cirrus ep93xx series of CPUs. The
ep93xx is an ARM920T based CPU with two VICs, PL010 based UARTs,
IrDA, MaverickCrunch floating point coprocessor, between 24 and 64
GPIOs, ethernet, OHCI USB and, depending on the model, pcmcia, raster
engine, graphics accelerator, IDE controller and a bunch of other
stuff.
This patch adds the core ep93xx support code, and support for the
Glomation GESBC-9312-sx and the Technologic Systems TS-72xx SBCs.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, OMAP platforms without the 32K timer left HZ set to
an empty value. Fix this by making the dependency on OMAP_32K_TIMER
rather than OMAP_32K_TIMER_HZ.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the HZ definition into Kconfig, and set appropriate defaults
for platforms. Remove mostly empty asm/arch/param.h include file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
This patches add the 1-wire drivers
to the ARM Kconfig.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
Chapter B2.7.3 in the latest ARM ARM (with v6 information) states that
the completion of a TLB maintenance operation is only guaranteed by
the execution of a DSB (Data Syncronization Barrier, formerly Data
Write Barrier or Drain Write Buffer).
Note that a DSB is only needed in the flush_tlb_kernel_* functions
since the completion is guaranteed by a mode change (i.e. switching
back to user mode) for the flush_tlb_user_* functions.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Although OABI_COMPAT works fine in most cases, it is still experimental
and could be for ever since it is nearly impossible to handle
everything, e.g. ioctls.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Martin Michlmayr
Minor typographical and spelling fixes in Konfig
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
---
Kconfig | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Martin Michlmayr
Add help descriptions to ARCH config items that don't have one.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
---
Kconfig | 32 ++++++++++++++++++++++++++++++--
mach-clps711x/Kconfig | 2 ++
2 files changed, 32 insertions(+), 2 deletions(-)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MTD_XIP depends on having working asm/mtd-xip.h; it's not just per-architecture
(arm-only, as current Kconfig would have it), but actually per-subarch as
well. Introduced a new symbol (ARCH_MTD_XIP) set by arch Kconfig; MTD_XIP
depends on it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Patch from Nicolas Pitre
We need NWFPE if we want to support execution of legacy binaries with
an EABI kernel.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This adds the configuration option, and disables any FPA floating point
emulators which are not EABI compatible.
It also disables Acorn RISC OS/Arthur binary support when CONFIG_EABI=y
since it is incompatible with an EABI kernel.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is the core of a small SPI framework, implementing the model of a
queue of messages which complete asynchronously (with thin synchronous
wrappers on top).
- It's still less than 2KB of ".text" (ARM). If there's got to be a
mid-layer for something so simple, that's the right size budget. :)
- The guts use board-specific SPI device tables to build the driver
model tree. (Hardware probing is rarely an option.)
- This version of Kconfig includes no drivers. At this writing there
are two known master controller drivers (PXA/SSP, OMAP MicroWire)
and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML
mentions of other drivers in development.
- No userspace API. There are several implementations to compare.
Implement them like any other driver, and bind them with sysfs.
The changes from last version posted to LKML (on 11-Nov-2005) are minor,
and include:
- One bugfix (removes a FIXME), with the visible effect of making device
names be "spiB.C" where B is the bus number and C is the chipselect.
- The "caller provides DMA mappings" mechanism now has kerneldoc, for
DMA drivers that want to be fancy.
- Hey, the framework init can be subsys_init. Even though board init
logic fires earlier, at arch_init ... since the framework init is
for driver support, and the board init support uses static init.
- Various additional spec/doc clarifications based on discussions
with other folk. It adds a brief "thank you" at the end, for folk
who've helped nudge this framework into existence.
As I've said before, I think that "protocol tweaking" is the main support
that this driver framework will need to evolve.
From: Mark Underwood <basicmark@yahoo.com>
Update the SPI framework to remove a potential priority inversion case by
reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from SAN People
Following changes were made to clock.c:
1) Replaced <asm/hardware/clock.h> with <linux/clk.h>
2) Removed old unused clk_enable & clk_disable.
3) Replaced clk_use/clk_unuse with clk_enable/clk_disable.
Otherwise it's the same as the previous patch.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Configurable 16-bit UID and friends support
This allows turning off the legacy 16 bit UID interfaces on embedded platforms.
text data bss dec hex filename
3330172 529036 190556 4049764 3dcb64 vmlinux-baseline
3328268 529040 190556 4047864 3dc3f8 vmlinux
From: Adrian Bunk <bunk@stusta.de>
UID16 was accidentially disabled for !EMBEDDED.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
EPXA10DB seems to be uncared for:
- the "PLD" code has never been merged
- no one has reported that this platform has been broken since
at least 2.6.10
- interest seems to have dried up around March 2003.
Therefore, remove EPXA10DB support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
ARM doesn't use ACPI so ARM's apm implementation has no need to depend
on PM_LEGACY. This patch removes that dependency.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ISA_DMA_API tells the rest of the kernel if the ISA DMA API is
available. Select this symbol only on machine types which make
use of the ISA DMA API.
Make building of arch/arm/kernel/dma.c depend on this symbol -
if a machine does not support the ISA DMA API, it's pointless
building this file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than defining our own PM option, use kernel/power/Kconfig.
This fixes build errors introduced by
bca73e4bf8
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes compilation for collie after -rc1 platform_device
changes. And yes, it even boots.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch adds support for omap24xx series of processors.
The files live in arch/arm/mach-omap2, and share common
files with omap15xx and omap16xx processors in
arch/arm/plat-omap.
Omap24xx support was originally added for 2.6.9 by TI.
This code was then improved and integrated to share common
code with omap15xx and omap16xx processors by various
omap developers, such as Paul Mundt, Juha Yrjola, Imre Deak,
Tony Lindgren, Richard Woodruff, Nishant Menon, Komal Shah
et al.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add infrastructure for supporting per-cpu local timers to update
the profiling information and update system time accounting.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
nwfpe extended precision emulation used to be broken on big-endian
and was therefore disabled. This patch fixes nwfpe so that it copies
extended precision floats to/from userspace in the proper word order
(similar to patch #2046, see the description of that patch for an
explanation) and reenables the Kconfig option.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
The AAEC-2000 has an ARM PrimeCell PL110 Color LCD Controller.
This patch contains the platform glue that will be used by specific boards.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Jon Ringle
Updated 2898/1 per comments:
- Removed fixup
- Moved code in mach-mp1000/ to mach-clps711x/
- Cleaned up code in mp1000-seprom.c. Eliminated code that displayed the contents of the eeprom
Please comment.
Signed-off-by: Jon Ringle
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Randy cleaned out the bulk of these stale references to the now long gone
Documentation/smp.tex back in 2004. I followed this up with a few more
sweeps. Somehow, these have managed to sneak back in since.
I can't seem to figure out a contact point for M32R (no one listed in
MAINTAINERS!), but, these patches are only but trivial.
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sanitized and fixed floppy dependencies: split the messy dependencies for
BLK_DEV_FD by introducing a new symbol (ARCH_MAY_HAVE_PC_FDC), making
BLK_DEV_FD depend on that one and taking declarations of ARCH_MAY_HAVE_PC_FDC
to arch/*/Kconfig. While we are at it, fixed several obvious cases when
BLK_DEV_FD should have been excluded (architectures lacking asm/floppy.h
are *not* going to have floppy.c compile, let alone work).
If you can come up with better name for that ("this architecture might
have working PC-compatible floppy disk controller"), you are more than
welcome - just s/ARCH_MAY_HAVE_PC_FDC/your_prefered_name/g in the patch
below...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This kills i386-specific stuff from arm Kconfig. Please apply,
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the core of the multimedia communication port
framework. This is a port used to communicate with devices
with two DMA paths and a control path.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Create a new top-level menu named "Networking" thus moving
net related options and protocol selection way from the drivers
menu and up on the top-level where they belong.
To implement this all architectures has to source "net/Kconfig" before
drivers/*/Kconfig in their Kconfig file. This change has been
implemented for all architectures.
Device drivers for ordinary NIC's are still to be found
in the Device Drivers section, but Bluetooth, IrDA and ax25
are located with their corresponding menu entries under the new
networking menu item.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Tony Lindgren
This patch adds minimal cpufreq support for OMAP
taking advantage of the clock framework.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch by various OMAP developers syncs the OMAP
specific arch files with the linux-omap tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch was suggested by RMK, and adds a warning on the accuracy
of timekeeping when using dynamic tick on some platforms. Depending
on the timer implementation, dynamic tick may affect the accuracy of
timekeeping.
Currently at least OMAP is known to have accurate timekeeping with
dynamic tick.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for Dynamic Tick Timer for ARM. Dynamic Tick is
also known as VST (Variable Scheduling Timeouts).
Dynamic Tick has been in use in the OMAP tree since last October. The
patch is not intrusive, and does not do anything unless CONFIG_NO_IDLE_HZ
is defined. This patch has the following fixed based on comments from
RMK:
- Time is updated before calling interrupt handlers.
- Added new interrupt flag SA_TIMER to avoid duplicate timer interrupts
- Moved struct dyn_tick_timer to time.h until we at some point probably
have an arch independent dyn-tick.h
- Cleaned up testing for DYN_TICK_ENABLED in irq.c
I've cleaned up this patch to fix some remaining issues:
- Call the timer tick handler with irqs disabled, as it would be from
a normal interrupt
- if we have a dyn_tick, we better implement all methods.
- generic timer_dyn_reprogram() call, to be called before sleeping
- added command line option - "dyntick=" to allow boot-time control
of this feature
-- rmk
Signed-off-by: Tony Lindgren
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For all architectures, this just means that you'll see a "Memory Model"
choice in your architecture menu. For those that implement DISCONTIGMEM,
you may eventually want to make your ARCH_DISCONTIGMEM_ENABLE a "def_bool
y" and make your users select DISCONTIGMEM right out of the new choice
menu. The only disadvantage might be if you have some specific things that
you need in your help option to explain something about DISCONTIGMEM.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Catalin Marinas
This patch adds PCI support for the Versatile PB926 platform.
Signed-off-by: Colin King
Signed-off-by: Catalin Marinas
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
Core support for AAEC-2000 based platforms.
This is an updated version of the previous patch, and takes
into account Russell's comments.
AAED-2000 default configuration will follow as soon
as some problems with the bootloader are sorted out...
Signed-off-by: Nicolas Bellido
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Brownell
The ARM generic Kconfig filters out IDE options ... except for
an error prone ARMload of special cases.
This adds one general case to the systems that will offer IDE options:
kernels with PCMCIA support, which probably want to use IDE to access
CompactFlash cards. This might allow many (most?) of the other cases
to disappear, for systems that only see IDE hardware through CF cards.
Right now this one patch is used to gate access to CF cards, including
MicroDrives, for both omap_cf and at91_cf drivers.
Signed-off-by: David Brownell
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vincent Sanders
This fixes the "multiple definitions of cpufreq_get" build faliure on
the hackkit SA1100 platform.
Signed-off-by: Vincent Sanders
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vincent Sanders
This fixes the "multiple definitions of cpufreq_get" build faliure on
the Badge4 SA1100 platform.
Signed-off-by: Vincent Sanders
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dave Neuer
This fixes the "multiple definitions of cpufreq_get" errors on
StrongARM-based iPAQs.
Signed-off-by: Dave Neuer
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than using a long "depends on..." and "default y" lines for
these options, use select instead.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
A bunch of drivers use ISA DMA helpers or their equivalents for
platforms that have ISA with different DMA controller (a lot of ARM
boxen). Currently there is no way to put such dependency in Kconfig -
CONFIG_ISA is not it (e.g. it is not set on platforms that have no ISA
slots, but have on-board devices that pretend to be ISA ones).
New symbol added - ISA_DMA_API. Set when we have functional
enable_dma()/set_dma_mode()/etc. set of helpers. Next patches in the
series will add missing dependencies for drivers that need them.
I'm very carefully staying the hell out of the recurring flamefest on
what exactly CONFIG_ISA would mean in ideal world - added symbol has a
well-defined meaning and for now I really want to treat it as completely
independent from the mess around CONFIG_ISA.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
