Add a module parameter to force the write protection mode of pmbus chips.
4 protections modes are provided to start with:
* 0: Remove the write protection
* 1: Disable all writes except to the WRITE_PROTECT, OPERATION,
PAGE, ON_OFF_CONFIG and VOUT_COMMAND commands
* 2: Disable all writes except to the WRITE_PROTECT, OPERATION and
PAGE commands
* 3: Disable all writes except to the WRITE_PROTECT command
Of course, if the parameter is not provided, the default write protection
status of the pmbus chips is left untouched.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writing PMBus protected registers does succeed from the smbus perspective,
even if the write is ignored by the device and a communication fault is
raised. This fault will silently be caught and cleared by pmbus irq if one
has been registered.
This means that the regulator call may return succeed although the
operation was ignored.
With this change, the operation which are not supported will be properly
flagged as such and the regulator framework won't even try to execute them.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[groeck: Adjust to EXPORT_SYMBOL_NS_GPL API change]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
PMBUS_NO_WRITE_PROTECT and PMBUS_USE_COEFFICIENTS_CMD flags have been added
to pmbus, but the corresponding documentation was not updated.
Update the documentation before adding new flags
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Message-ID: <20241105-tps25990-v4-1-0e312ac70b62@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Enabling and disabling PEC for PMBus devices is currently only supported
with a debugfs attribute, which requires debugfs to be enabled and is
thus less than perfect. Take the lm90 driver as example and add a 'pec'
attribute to the I2C device if both the I2C adapter and the PMBus device
support it. Remove the now obsolete 'pec' attribute from debugfs.
Cc: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add documentation for the new pmbus flags PMBUS_WRITE_PROTECTED,
PMBUS_NO_CAPABILITY and PMBUS_READ_STATUS_AFTER_FAILED_CHECK
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210507194023.61138-3-erik.rosen@metormote.com
[groeck: Added newline at end of file]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The only action currently performed in pmbus_do_remove() is removing the
debugfs hierarchy. We can schedule a devm action at probe time and remove
pmbus_do_remove() entirely from all pmbus drivers.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20201026105352.20359-1-brgl@bgdev.pl
[groeck: Removed references to pmbus_do_remove from documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pmbus_do_probe doesn't use the id information provided in its second
argument, so this can be removed, which then allows using the
single-parameter i2c probe function ("probe_new") for probes.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified as follows:
* if the information in i2c_client is sufficient, that's used instead
(client->name);
* configured v. probed comparisons are performed by comparing the
configured name to the detected name, instead of the ids; this
involves strcmp but is still cheaper than comparing all the device
names when scanning the tables;
* anything else is handled by calling i2c_match_id() with the same
level of error-handling (if any) as before.
Additionally, the mismatch message in the ltc2978 driver is adjusted
so that it no longer assumes that the driver_data is an index into
ltc2978_id.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20200808210004.30880-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In preparation for multi-phase support, add 'phase' parameter to read_word
and set_page functions. Actual multi-phase support will be added in
a subsequent patch.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Now that all files were converted to ReST format, rename them
and add an index.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
