Document that receiver drivers should call v4l2_get_link_freq() to obtain
the link frequency.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The subsection on stopping the transmitter belongs to the generic part and
is not specific to CSI-2. Move it out of the CSI-2 section.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Add the get_mbus_config() as the means for conveying the link frequency
towards the receiver drivers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The scope of the s_stream video operation is now fully supported by
{enable,disable}_streams. Explicitly document the s_stream() op as
deprecated and update the related documentation.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
LP-11 and LP-111 are CSI-2 bus states, not modes. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
BT.601 is not actually a bus specification, leaving parallel bus without a
specification to refer to. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Rework LP-11 and LP-111 mode documentation to make it more understandable
and useful. This involves adding pre_streamon and post_streamon callbacks
that make it possible to explicitly transition the transmitter to either
mode.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix kerneldoc syntax in v4l2-async. The references were not produced
correctly.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Modernise the documentation to make it more precise and update the use of
pixel rate control and various other changes. In particular:
- Use non-proportional font for file names, properties as well as
controls.
- The unit of the HBLANK control is pixels, not lines.
- The unit of PIXEL_RATE control is pixels per second, not Hz.
- Merge common requirements for CSI-2 and parallel busses.
- Include all DT properties needed for assigned clocks.
- Fix referencing the link rate control.
- SMIA driver's new name is CCS driver.
- The PIXEL_RATE control denotes pixel rate on the pixel array on camera
sensors. Do not suggest it is used to tell the maximum pixel rate on the
bus anymore.
- Improve ReST syntax (plain struct and function names).
- Remove the suggestion to use s_power() in receiver drivers.
- Make MIPI website URL use HTTPS, add Wikipedia links to BT.601 and
BT.656.
Fixes: e4cf8c58af ("media: Documentation: media: Document how to write camera sensor drivers")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
