The current documentation does not clearly explain how to invert the SPI
CS signal to make it active-high. This makes it very difficult to
understand.
This patch adds a simple explanation on how to set the CS line in
active-high and adds an example to make it easier for users who need
that setup for their SPI peripherals.
Link: https://forums.raspberrypi.com/viewtopic.php?t=378222
Signed-off-by: Iker Pedrosa <ikerpedrosam@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20241216095739.27320-1-ikerpedrosam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are SPI IPs that can be configured by the integrator with a
specific FIFO depth depending on the system's capabilities. For example,
the samsung USI SPI IP can be configured by the integrator with a TX/RX
FIFO from 8 byte to 256 bytes.
Introduce the ``fifo-depth`` property for such instances of IPs where the
same FIFO depth is used for both RX and TX. Introduce ``rx-fifo-depth``
and ``tx-fifo-depth`` properties for cases where the RX FIFO depth is
different from the TX FIFO depth.
Make the dedicated RX/TX properties dependent on each other and mutual
exclusive with the other.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://msgid.link/r/20240216070555.2483977-2-tudor.ambarus@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the pattern matching node names a bit stricter to improve DTS
consistency. The pattern is restricted to:
1. Only one unit address or one -N suffix,
2. -N suffixes to decimal numbers.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230530144851.92059-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Just as unevaluatedProperties or additionalProperties are required at
the top level of schemas, they should (and will) also be required for
child node schemas. That ensures only documented properties are
present.
Add unevaluatedProperties or additionalProperties as appropriate, and
then add any missing properties flagged by the addition.
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Lee Jones <lee@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230124230228.372305-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
The Devicetree bindings document does not have to say in the title that
it is a "binding", but instead just describe the hardware. For shared
(re-usable) schemas, name them all as "common properties".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net> # watchdog
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # IIO
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # MMC
Acked-by: Stephen Boyd <sboyd@kernel.org> # clk
Acked-by: Vinod Koul <vkoul@kernel.org> # dma
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # media
Acked-by: Sebastian Reichel <sre@kernel.org> # power
Acked-by: Viresh Kumar <viresh.kumar@linaro.org> # opp
Link: https://lore.kernel.org/r/20221216163815.522628-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
The spi-3wire property is device specific and should be accepted only if
device really needs them. Drop it from common spi-peripheral-props.yaml
schema, mention in few panel drivers which use it and include instead in
the SPI controller bindings. The controller bindings will provide
spi-3wire type validation and one place for description. Each device
schema must list the property if it is applicable.
The Samsung S6E63M0 panel uses also spi-cpha/cpol properties on at least
one board (ste-ux500-samsung-janice/dts), so add also these to the
panel's bindings.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220810131311.428645-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-cpha and spi-cpol properties are device specific and should be
accepted only if device really needs them. Drop them from common
spi-peripheral-props.yaml schema, mention in few panel drivers which use
them and include instead in the SPI controller bindings. The controller
bindings will provide CPHA/CPOL type validation and one place for
description. Each device schema must list the properties if they are
applicable.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220722191539.90641-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
- Add Krzysztof Kozlowski as co-maintainer for DT bindings providing
much needed help.
- DT schema validation now takes DTB files as input rather than
intermediate YAML files. This decouples the validation from the source
level syntax information. There's a bunch of schema fixes as a result
of switching to DTB based validation which exposed some errors
and incomplete schemas and examples.
- Kbuild improvements to explicitly warn users running 'make
dt_binding_check' on missing yamllint
- Expand DT_SCHEMA_FILES kbuild variable to take just a partial filename
or path instead of the full path to 1 file.
- Convert various bindings to schema format: mscc,vsc7514-switch,
multiple GNSS bindings, ahci-platform, i2c-at91, multiple UFS
bindings, cortina,gemini-sata-bridge, cortina,gemini-ethernet, Atmel
SHA, Atmel TDES, Atmel AES, armv7m-systick, Samsung Exynos display
subsystem, nuvoton,npcm7xx-timer, samsung,s3c2410-i2c, zynqmp_dma,
msm/mdp4, rda,8810pl-uart
- New schemas for u-boot environment variable partition, TI clksel
- New compatible strings for Renesas RZ/V2L SoC
- Vendor prefixes for Xen, HPE, deprecated Synopsys, deprecated HiSilicon
- Add/fix schemas for QEMU Arm 'virt' machine
- Drop unused of_alias_get_alias_list() function
- Add a script to check DT unittest EXPECT message output. Pass messages
also now print by default at PR_INFO level to help test automation.
-----BEGIN PGP SIGNATURE-----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=g1li
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Add Krzysztof Kozlowski as co-maintainer for DT bindings providing
much needed help.
- DT schema validation now takes DTB files as input rather than
intermediate YAML files. This decouples the validation from the
source level syntax information. There's a bunch of schema fixes as a
result of switching to DTB based validation which exposed some errors
and incomplete schemas and examples.
- Kbuild improvements to explicitly warn users running 'make
dt_binding_check' on missing yamllint
- Expand DT_SCHEMA_FILES kbuild variable to take just a partial
filename or path instead of the full path to 1 file.
- Convert various bindings to schema format: mscc,vsc7514-switch,
multiple GNSS bindings, ahci-platform, i2c-at91, multiple UFS
bindings, cortina,gemini-sata-bridge, cortina,gemini-ethernet, Atmel
SHA, Atmel TDES, Atmel AES, armv7m-systick, Samsung Exynos display
subsystem, nuvoton,npcm7xx-timer, samsung,s3c2410-i2c, zynqmp_dma,
msm/mdp4, rda,8810pl-uart
- New schemas for u-boot environment variable partition, TI clksel
- New compatible strings for Renesas RZ/V2L SoC
- Vendor prefixes for Xen, HPE, deprecated Synopsys, deprecated
HiSilicon
- Add/fix schemas for QEMU Arm 'virt' machine
- Drop unused of_alias_get_alias_list() function
- Add a script to check DT unittest EXPECT message output. Pass
messages also now print by default at PR_INFO level to help test
automation.
* tag 'devicetree-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (96 commits)
dt-bindings: kbuild: Make DT_SCHEMA_LINT a recursive variable
dt-bindings: nvmem: add U-Boot environment variables binding
dt-bindings: ufs: qcom: Add SM6350 compatible string
dt-bindings: dmaengine: sifive,fu540-c000: include generic schema
dt-bindings: gpio: pca95xx: drop useless consumer example
Revert "of: base: Introduce of_alias_get_alias_list() to check alias IDs"
dt-bindings: virtio,mmio: Allow setting devices 'dma-coherent'
dt-bindings: gnss: Add two more chips
dt-bindings: gnss: Rewrite sirfstar binding in YAML
dt-bindings: gnss: Modify u-blox to use common bindings
dt-bindings: gnss: Rewrite common bindings in YAML
dt-bindings: ata: ahci-platform: Add rk3568-dwc-ahci compatible
dt-bindings: ata: ahci-platform: Add power-domains property
dt-bindings: ata: ahci-platform: Convert DT bindings to yaml
dt-bindings: kbuild: Use DTB files for validation
dt-bindings: kbuild: Pass DT_SCHEMA_FILES to dt-validate
dt-bindings: Add QEMU virt machine compatible
dt-bindings: arm: Convert QEMU fw-cfg to DT schema
dt-bindings: i2c: at91: Add SAMA7G5 compatible strings list
dt-bindings: i2c: convert i2c-at91 to json-schema
...
Another pass at removing unnecessary use of 'allOf' with a '$ref'.
json-schema versions draft7 and earlier have a weird behavior in that
any keywords combined with a '$ref' are ignored (silently). The correct
form was to put a '$ref' under an 'allOf'. This behavior is now changed
in the 2019-09 json-schema spec and '$ref' can be mixed with other
keywords.
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Marek Behún <kabel@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220228213802.1639658-1-robh@kernel.org
Many SPI controllers need to add properties to peripheral devices. This
could be the delay in clock or data lines, etc. These properties are
controller specific but need to be defined in the peripheral node
because they are per-peripheral and there can be multiple peripherals
attached to a controller.
If these properties are not added to the peripheral binding, then the
dtbs check emits a warning. But these properties do not make much sense
in the peripheral binding because they are controller-specific and they
will just pollute every peripheral binding. So this binding is added to
collect all such properties from all such controllers. Peripheral
bindings should simply refer to this binding and they should be rid of
the warnings.
There are some limitations with this approach. Firstly, there is no way
to specify required properties. The schema contains properties for all
controllers and there is no way to know which controller is being used.
Secondly, there is no way to restrict additional properties. Since this
schema will be used with an allOf operator, additionalProperties needs
to be true. In addition, the peripheral schema will have to set
unevaluatedProperties: false.
Despite these limitations, this appears to be the best solution to this
problem that doesn't involve modifying existing tools or schema specs.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211109181911.2251-2-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There's no need for fixed strings to be under 'patternProperties', so move
them under 'properties' instead.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Saravanan Sekar <sravanhome@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: linux-hwmon@vger.kernel.org
Cc: linux-phy@lists.infradead.org
Cc: linux-spi@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210713193514.690894-1-robh@kernel.org
Add binding support for devices, that have more than one
chip select. A typical example are SPI connected microcontroller,
that can also be programmed over SPI like NXP Kinetis or
chips with a configuration and a data chip select, such as
Microchip's MRF89XA transceiver.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210621175359.126729-3-sebastian.reichel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding checks for undocumented compatible strings reveals a bunch of
warnings in the DT binding examples. Fix the cases which are typos, just
a mismatch between the schema and the example, or aren't documented at all.
In a couple of cases, fixing the compatible revealed some schema errors
which are fixed.
There's a bunch of others remaining after this which have bindings, but
those aren't converted to schema yet.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: linux-clk@vger.kernel.org
Cc: dmaengine@vger.kernel.org
Cc: linux-i3c@lists.infradead.org
Cc: linux-iio@vger.kernel.org
Cc: linux-leds@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20210316194918.3528417-1-robh@kernel.org
Following a change to the SPI framework, providing a value of zero for
'spi-rx-bus-width' and 'spi-tx-bus-width' is now possible and will
essentially mean that no RX or TX is allowed.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201221152936.53873-3-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
scripts/dtc/checks.c:
if (get_property(node, "spi-slave"))
spi_addr_cells = 0;
if (node_addr_cells(node) != spi_addr_cells)
FAIL(c, dti, node, "incorrect #address-cells for SPI bus");
if (node_size_cells(node) != 0)
FAIL(c, dti, node, "incorrect #size-cells for SPI bus");
The above code in check_spi_bus_bridge() require that the number of address
cells must be 0. So we should explicitly declare "#address-cells = <0>".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20201013160845.1772-4-thunder.leizhen@huawei.com
Signed-off-by: Rob Herring <robh@kernel.org>
In order to add meta-schema checks for additional/unevaluatedProperties
being present, all schema need to make this explicit. As common/shared
schema are included by other schemas, they should always allow for
additionalProperties.
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201005183830.486085-5-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
json-schema versions draft7 and earlier have a weird behavior in that
any keywords combined with a '$ref' are ignored (silently). The correct
form was to put a '$ref' under an 'allOf'. This behavior is now changed
in the 2019-09 json-schema spec and '$ref' can be mixed with other
keywords. The json-schema library doesn't yet support this, but the
tooling now does a fixup for this and either way works.
This has been a constant source of review comments, so let's change this
treewide so everyone copies the simpler syntax.
Scripted with ruamel.yaml with some manual fixups. Some minor whitespace
changes from the script.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for I2C
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for-iio
Reviewed-by: Stephen Boyd <sboyd@kernel.org> # clock
Signed-off-by: Rob Herring <robh@kernel.org>
The descriptions for the spi-rx-bus-width and spi-tx-bus-width
properties refer to "MISO" and "MOSI", which are not explained in the
document. While these abbreviations are fairly common when talking
about SPI, and thus may not need an explanation, they are not entirely
correct in this context, as the SPI controller may be used in slave mode
instead of master mode.
Fix this by replacing them by "read transfers" resp. "write transfers",
like is done for the spi-rx-delay-us and spi-tx-delay-us properties.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200306085038.8111-3-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the DT bindings for an SPI controller specify that
"#address-cells" must be fixed to one. However, that applies to an SPI
controller in master mode only. When running in SPI slave mode,
"#address-cells" should not be specified.
Fix this making "#address-cells" mutually-exclusive with "spi-slave".
Fixes: 0a1b929356 ("spi: Add YAML schemas for the generic SPI options")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200306085038.8111-2-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core supports Octal SPI controllers which have 8 IO lines.
Therefore document 8 as a valid option for spi-tx{rx}-bus-width
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200102102118.23318-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The number of CS lines is mentioned as 2 in the spi-controller binding
but however in the example, 4 cs-gpios are used. Hence fix that to
mention 4.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20190820115000.32041-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Mixing array constraints like 'maxItems' and string or integer value
constraints like 'minimum' don't make sense. Also, with only value
constraints, it is implied we have a single value. So lets remove
'maxItems: 1'.
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20190709192631.16394-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI controllers have a bunch of generic options that are needed in a
device tree. Add a YAML schemas for those.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
