Changes since v2:
-----------------
- v2 series can be found here: https://lore.kernel.org/linux-arm-msm/20210615074543.26700-1-bhupesh.sharma@linaro.org/T/#m8303d27d561b30133992da88198abb78ea833e21
- Addressed review comments from Bjorn and Mark.
- As per suggestion from Bjorn, seperated the patches in different
patchsets (specific to each subsystem) to ease review and patch application.
Changes since v1:
-----------------
- v1 series can be found here: https://lore.kernel.org/linux-arm-msm/20210607113840.15435-1-bhupesh.sharma@linaro.org/T/#mc524fe82798d4c4fb75dd0333318955e0406ad18
- Addressed review comments from Bjorn and Vinod received on the v1
series.
This series adds the regulator support code for SA8155p-adp board
which is based on Qualcomm snapdragon sa8155p SoC which in turn is
simiar to the sm8150 SoC.
This board supports a new PMIC PMM8155AU.
While at it, also make some cosmetic changes to the regulator driver
and dt-bindings to make sure the compatibles are alphabetical and also
fix issues with extra comma(s) at the end of terminator line(s).
Cc: Mark Brown <broonie@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Bhupesh Sharma (5):
dt-bindings: regulator: qcom,rpmh-regulator: Arrange compatibles
alphabetically
dt-bindings: regulator: qcom,rpmh-regulator: Add compatible for
SA8155p-adp board pmic
regulator: qcom-rpmh: Cleanup terminator line commas
regulator: qcom-rpmh: Add terminator at the end of pm7325x_vreg_data[]
array
regulator: qcom-rpmh: Add new regulator found on SA8155p adp board
.../regulator/qcom,rpmh-regulator.yaml | 17 ++---
drivers/regulator/qcom-rpmh-regulator.c | 62 +++++++++++++++----
2 files changed, 59 insertions(+), 20 deletions(-)
--
2.31.1
Extend regulator notification support
This series extends the regulator notification and error flag support.
Initial discussion on the topic can be found here:
https://lore.kernel.org/lkml/6046836e22b8252983f08d5621c35ececb97820d.camel@fi.rohmeurope.com/
In a nutshell - the series adds:
1. WARNING level events/error flags. (Patch 3)
Current regulator 'ERROR' event notifications for over/under
voltage, over current and over temperature are used to indicate
condition where monitored entity is so badly "off" that it actually
indicates a hardware error which can not be recovered. The most
typical hanling for that is believed to be a (graceful)
system-shutdown. Here we add set of 'WARNING' level flags to allow
sending notifications to consumers before things are 'that badly off'
so that consumer drivers can implement recovery-actions.
2. Device-tree properties for specifying limit values. (Patches 1, 5)
Add limits for above mentioned 'ERROR' and 'WARNING' levels (which
send notifications to consumers) and also for a 'PROTECTION' level
(which will be used to immediately shut-down the regulator(s) W/O
informing consumer drivers. Typically implemented by hardware).
Property parsing is implemented in regulator core which then calls
callback operations for limit setting from the IC drivers. A
warning is emitted if protection is requested by device tree but the
underlying IC does not support configuring requested protection.
3. Helpers which can be registered by IC. (Patch 4)
Target is to avoid implementing IRQ handling and IRQ storm protection
in each IC driver. (Many of the ICs implementin these IRQs do not allow
masking or acking the IRQ but keep the IRQ asserted for the whole
duration of problem keeping the processor in IRQ handling loop).
4. Emergency poweroff function (refactored out of the thermal_core to
kernel/reboot.c) which is called if IC fires error IRQs but IC reading
fails and given retry-count is exceeded. (Patches 2, 4)
Please note that the mutex in the emergency shutdown was replaced by a
simple atomic in order to allow call from any context.
The helper was attempted to be done so it could be used to implement
roughly same logic as is used in qcom-labibb regulator. This means
amongst other things a safety shut-down if IC registers are not readable.
Using these shut-down retry counters are optional. The idea is that the
helper could be also used by simpler ICs which do not provide status
register(s) which can be used to check if error is still active.
ICs which do not have such status register can simply omit the 'renable'
callback (and retry-counts etc) - and helper assumes the situation is Ok
and re-enables IRQ after given time period. If problem persists the
handler is ran again and another notification is sent - but at least the
delay allows processor to avoid IRQ loop.
Patch 7 takes this notification support in use at BD9576MUF.
Patch 8 is related to MFD change which is not really related to the RFC
here. It was added to this series in order to avoid potential conflicts.
Patch 9 adds a maintainers entry.
Changelog v10-RESEND:
- rebased on v5.13-rc4
Changelog v10:
- rebased on v5.13-rc2
- Move rdev_*() print macros to the internal.h and use rdev_dbg()
from irq_helpers.c
- Export rdev_get_name() and move it from coupler.h to driver.h for
others to use. (It was already in coupler.h but not exported -
usage was limited and coupler.h does not sound like optimal place
as rdev_name is not only used by coupled regulators)
- Send all regulator notifications from irq_helpers.c at one OR'd
event for the sake of simplicity. For BD9576 this does not matter
as it has own IRQ for each event case. Header defining events says
they may be OR'd.
- Change WARN() at protection shutdown to pr_emerg as suggested by
Petr.
Changelog v9:
- rebases on v5.13-rc1
- Update thermal documentation
- Fix regulator notification event number
Changelog v8:
- split shutdown API adding and thermal core taking it in use to
own patches.
- replace the spinlock with atomic when ensuring the emergency
shutdown is only called once.
Changelog v7:
general:
- rebased on v5.12-rc7
- new patch for refactoring the hw-failure reboot logic out of
thermal_core.c for others to use.
notification helpers:
- fix regulator error_flags query
- grammar/typos
- do not BUG() but attempt to shut-down the system
- use BITS_PER_TYPE()
Changelog v6:
Add MAINTAINERS entry
Changes to IRQ notifiers
- move devm functions to drivers/regulator/devres.c
- drop irq validity check
- use devm_add_action_or_reset()
- fix styling issues
- fix kerneldocs
Changelog v5:
- Fix the badly formatted pr_emerg() call.
Changelog v4:
- rebased on v5.12-rc6
- dropped RFC
- fix external FET DT-binding.
- improve prints for cases when expecting HW failure.
- styling and typos
Changelog v3:
Regulator core:
- Fix dangling pointer access at regulator_irq_helper()
stpmic1_regulator:
- fix function prototype (compile error)
bd9576-regulator:
- Update over current limits to what was given in new data-sheet
(REV00K)
- Allow over-current monitoring without external FET. Set limits to
values given in data-sheet (REV00K).
Changelog v2:
Generic:
- rebase on v5.12-rc2 + BD9576 series
- Split devm variant of delayed wq to own series
Regulator framework:
- Provide non devm variant of IRQ notification helpers
- shorten dt-property names as suggested by Rob
- unconditionally call map_event in IRQ handling and require it to be
populated
BD9576 regulators:
- change the FET resistance property to micro-ohms
- fix voltage computation in OC limit setting
BD9576MUF provides over-current protection and detection. Current is
measured as voltage loss over external FET. Allow specifying FET's on
resistance so current monitoring limits can be converted to voltages.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/e5feb160d7e09f33fff5b88f1928c66a15c6680f.1622628334.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Support specifying protection/error/warning limits for regulator
over current, over temperature and over/under voltage.
Most of the PMICs support only "protection" feature but few
setups do also support error/warning level indications.
On many ICs most of the protection limits can't actually be set.
But for example the ampere limit for over-current protection on ROHM
BD9576 can be configured - or feature can be completely disabled.
Provide limit setting for all protections/errors for the sake of
the completeness and do that using own properties for all so that
not all users would need to set all levels when only one or few are
supported.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/ae2c6056d5ed1334912d27e736d23c9151065433.1622628333.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add compatible string for pmm8155au pmic found on
the SA8155p-adp board.
Cc: Mark Brown <broonie@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210617051712.345372-3-bhupesh.sharma@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
add dt-binding document for MediaTek MT6359 PMIC
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Add support for Software Nodes to MFD Core
- Remove support for Device Properties from MFD Core
- Use standard APIs in MFD Core
- New Drivers
- Add support for ROHM BD9576MUF and BD9573MUF PMICs
- Add support for Netronix Embedded Controller, PWM and RTC
- Add support for Actions Semi ATC260x PMICs and OnKey
- New Device Support
- Add support for DG1 PCIe Graphics Card to Intel PMT
- Add support for ROHM BD71815 PMIC to ROHM BD71828
- Add support for Tolino Shine 2 HD to Netronix Embedded Controller
- Add support for AX10 BMC Secure Updates to Intel M10 BMC
- Removed Device Support
- Remove Arizona Extcon support from MFD
- Remove ST-E AB8500 Power Supply code from MFD
- Remove AB3100 altogether
- New Functionality
- Add support for SMBus and I2C modes to Dialog DA9063
- Switch to using Software Nodes in Intel (various)
- New/converted Device Tree bindings; rohm,bd71815-pmic, rohm,bd9576-pmic,
netronix,ntxec, actions,atc260x,
ricoh,rn5t618, qcom-pm8xxx
- Fix-ups
- Fix error handling/path; intel_pmt
- Simplify code; rohm-bd718x7, ab8500-core, intel-m10-bmc
- Trivial clean-ups (reordering, spelling); rohm-generic, rn5t618, max8997
- Use correct data-type; db8500-prcmu
- Remove superfluous code; lp87565, intel_quark_i2c_gpi, lpc_sch, twl
- Use generic APIs/defines; lm3533-core, intel_quark_i2c_gpio
- Regmap related fix-ups; intel-m10-bmc, sec-core
- Reorder resource freeing during remove; intel_quark_i2c_gpio
- Make table indexing more robust; intel_quark_i2c_gpio
- Fix reference imbalances; arizona-irq
- Staticify and (un)constify things; arizona-spi, stmpe, ene-kb3930,
intel-lpss-acpi, intel-lpss-pci,
atc260x-i2c, intel_quark_i2c_gpio
- Bug Fixes
- Fix incorrect (register) values; intel-m10-bmc
- Kconfig related fixes; ABX500_CORE
- Do not clear the Auto Reload Register; stm32-timers
-----BEGIN PGP SIGNATURE-----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=IJSL
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Add support for Software Nodes to MFD Core
- Remove support for Device Properties from MFD Core
- Use standard APIs in MFD Core
New Drivers:
- Add support for ROHM BD9576MUF and BD9573MUF PMICs
- Add support for Netronix Embedded Controller, PWM and RTC
- Add support for Actions Semi ATC260x PMICs and OnKey
New Device Support:
- Add support for DG1 PCIe Graphics Card to Intel PMT
- Add support for ROHM BD71815 PMIC to ROHM BD71828
- Add support for Tolino Shine 2 HD to Netronix Embedded Controller
- Add support for AX10 BMC Secure Updates to Intel M10 BMC
Removed Device Support:
- Remove Arizona Extcon support from MFD
- Remove ST-E AB8500 Power Supply code from MFD
- Remove AB3100 altogether
New Functionality:
- Add support for SMBus and I2C modes to Dialog DA9063
- Switch to using Software Nodes in Intel (various)
New/converted Device Tree bindings:
- rohm bd71815-pmic, rohm bd9576-pmic, netronix ntxec, actions
atc260x, ricoh rn5t618, qcom pm8xxx
- Fix-ups:
- Fix error handling/path; intel_pmt
- Simplify code; rohm-bd718x7, ab8500-core, intel-m10-bmc
- Trivial clean-ups (reordering, spelling); rohm-generic, rn5t618,
max8997
- Use correct data-type; db8500-prcmu
- Remove superfluous code; lp87565, intel_quark_i2c_gpi, lpc_sch, twl
- Use generic APIs/defines; lm3533-core, intel_quark_i2c_gpio
- Regmap related fix-ups; intel-m10-bmc, sec-core
- Reorder resource freeing during remove; intel_quark_i2c_gpio
- Make table indexing more robust; intel_quark_i2c_gpio
- Fix reference imbalances; arizona-irq
- Staticify and (un)constify things; arizona-spi, stmpe, ene-kb3930,
intel-lpss-acpi, intel-lpss-pci, atc260x-i2c, intel_quark_i2c_gpio
Bug Fixes:
- Fix incorrect (register) values; intel-m10-bmc
- Kconfig related fixes; ABX500_CORE
- Do not clear the Auto Reload Register; stm32-timers"
* tag 'mfd-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (84 commits)
mfd: intel-m10-bmc: Add support for MAX10 BMC Secure Updates
Revert "mfd: max8997: Add of_compatible to Extcon and Charger mfd_cell"
mfd: twl: Remove unused inline function twl4030charger_usb_en()
dt-bindings: mfd: Convert pm8xxx bindings to yaml
dt-bindings: mfd: Add compatible for pmk8350 rtc
i2c: designware: Get rid of legacy platform data
mfd: intel_quark_i2c_gpio: Convert I²C to use software nodes
mfd: lpc_sch: Partially revert "Add support for Intel Quark X1000"
mfd: arizona: Fix rumtime PM imbalance on error
mfd: max8997: Replace 8998 with 8997
mfd: core: Use acpi_find_child_device() for child devices lookup
mfd: intel_quark_i2c_gpio: Don't play dirty trick with const
mfd: intel_quark_i2c_gpio: Enable MSI interrupt
mfd: intel_quark_i2c_gpio: Reuse BAR definitions for MFD cell indexing
mfd: ntxec: Support for EC in Tolino Shine 2 HD
mfd: stm32-timers: Avoid clearing auto reload register
mfd: intel_quark_i2c_gpio: Replace I²C speeds with descriptive definitions
mfd: intel_quark_i2c_gpio: Remove unused struct device member
mfd: intel_quark_i2c_gpio: Unregister resources in reversed order
mfd: Kconfig: ABX500_CORE should depend on ARCH_U8500
...
- Refactoring powerpc and arm64 kexec DT handling to common code. This
enables IMA on arm64.
- Add kbuild support for applying DT overlays at build time. The first
user are the DT unittests.
- Fix kerneldoc formatting and W=1 warnings in drivers/of/
- Fix handling 64-bit flag on PCI resources
- Bump dtschema version required to v2021.2.1
- Enable undocumented compatible checks for dtbs_check. This allows
tracking of missing binding schemas.
- DT docs improvements. Regroup the DT docs and add the example schema
and DT kernel ABI docs to the doc build.
- Convert Broadcom Bluetooth and video-mux bindings to schema
- Add QCom sm8250 Venus video codec binding schema
- Add vendor prefixes for AESOP, YIC System Co., Ltd, and Siliconfile
Technologies Inc.
- Cleanup of DT schema type references on common properties and
standard unit properties
-----BEGIN PGP SIGNATURE-----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=rF27
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Refactor powerpc and arm64 kexec DT handling to common code. This
enables IMA on arm64.
- Add kbuild support for applying DT overlays at build time. The first
user are the DT unittests.
- Fix kerneldoc formatting and W=1 warnings in drivers/of/
- Fix handling 64-bit flag on PCI resources
- Bump dtschema version required to v2021.2.1
- Enable undocumented compatible checks for dtbs_check. This allows
tracking of missing binding schemas.
- DT docs improvements. Regroup the DT docs and add the example schema
and DT kernel ABI docs to the doc build.
- Convert Broadcom Bluetooth and video-mux bindings to schema
- Add QCom sm8250 Venus video codec binding schema
- Add vendor prefixes for AESOP, YIC System Co., Ltd, and Siliconfile
Technologies Inc.
- Cleanup of DT schema type references on common properties and
standard unit properties
* tag 'devicetree-for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (64 commits)
powerpc: If kexec_build_elf_info() fails return immediately from elf64_load()
powerpc: Free fdt on error in elf64_load()
of: overlay: Fix kerneldoc warning in of_overlay_remove()
of: linux/of.h: fix kernel-doc warnings
of/pci: Add IORESOURCE_MEM_64 to resource flags for 64-bit memory addresses
dt-bindings: bcm4329-fmac: add optional brcm,ccode-map
docs: dt: update writing-schema.rst references
dt-bindings: media: venus: Add sm8250 dt schema
of: base: Fix spelling issue with function param 'prop'
docs: dt: Add DT API documentation
of: Add missing 'Return' section in kerneldoc comments
of: Fix kerneldoc output formatting
docs: dt: Group DT docs into relevant sub-sections
docs: dt: Make 'Devicetree' wording more consistent
docs: dt: writing-schema: Include the example schema in the doc build
docs: dt: writing-schema: Remove spurious indentation
dt-bindings: Fix reference in submitting-patches.rst to the DT ABI doc
dt-bindings: ddr: Add optional manufacturer and revision ID to LPDDR3
dt-bindings: media: video-interfaces: Drop the example
devicetree: bindings: clock: Minor typo fix in the file armada3700-tbg-clock.txt
...
Add a compatible string to support TCS4525/TCS4526 devices,
which are compatible with Fairchild FAN53555 regulators.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Link: https://lore.kernel.org/r/20210421210338.43819-2-ezequiel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add binding documentation for regulators on ROHM BD71815 PMIC.
5 bucks, 7 LDOs and a boost for LED.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Properties with standard unit suffixes already have a type and don't need
type references. Fix a few more cases which have gotten added.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Kevin Tsai <ktsai@capellamicro.com>
Cc: linux-iio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Dmity Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20210316194824.3526913-1-robh@kernel.org
- Cleanups on properties with standard unit suffixes
- Fix overwriting dma_range_map if there's no 'dma-ranges' property
- Fix a bug when creating a /chosen node from ARM ATAGs
- Add missing properties for TI j721e USB binding
- Several doc reference updates due to DT schema conversions
-----BEGIN PGP SIGNATURE-----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=oW7V
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Cleanups on properties with standard unit suffixes
- Fix overwriting dma_range_map if there's no 'dma-ranges' property
- Fix a bug when creating a /chosen node from ARM ATAGs
- Add missing properties for TI j721e USB binding
- Several doc reference updates due to DT schema conversions
* tag 'devicetree-fixes-for-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: Cleanup standard unit properties
of/device: Update dma_range_map only when dev has valid dma-ranges
ARM: zImage: atags_to_fdt: Fix node names on added root nodes
dt-bindings: usb: j721e: add ranges and dma-coherent props
dt-bindings:iio:adc: update adc.yaml reference
dt-bindings: memory: mediatek: update mediatek,smi-larb.yaml references
dt-bindings: display: mediatek: update mediatek,dpi.yaml reference
ASoC: audio-graph-card: update audio-graph-card.yaml reference
Short-Circuit Protection (SCP) and Over-Current Protection (OCP) are
now implemented in the driver: document the interrupts.
This also fixes wrong documentation about the SCP interrupt for LAB.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210119174421.226541-7-angelogioacchino.delregno@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Document properties to configure soft start and discharge resistor
for LAB and IBB respectively.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210119174421.226541-5-angelogioacchino.delregno@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This property seems useless because we can use the
regulator-max-microamp generic property to do the same
and using generic code.
As this property was already released in a kernel version,
we can't remove it, just mark it as deprecated
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Link: https://lore.kernel.org/r/20210114174714.122561-4-adrien.grassein@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
nxp,phase-shift is an enum so use enum format to describe it.
Minimum and maximum values are also wrong.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210114174714.122561-3-adrien.grassein@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
PM8009 has special revision (P=1), which is to be used for sm8250
platform. The major difference is the S2 regulator which supplies 0.95 V
instead of 2.848V. Declare regulators data to be used for this chip
revision. The datasheet calls the chip just pm8009-1, so use the same
name.
base-commit: 5c8fe583cc
PMIC pm8009 has special revision (P=1) made for sm8250 platform. The
major difference is the S2 regulator which supplies 0.95 V instead of
2.848V. Add special compatibility string for this chip revision.
The datasheet calls the chip just pm8009-1, so use the same name.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201231122348.637917-2-dmitry.baryshkov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
*-supply properties are always a single phandle, so binding schemas
don't need a type $ref nor 'maxItems'.
A meta-schema check for this is pending once these existing cases are
fixed.
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-iio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: linux-media@vger.kernel.org
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20201221234659.824881-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
The pf8x00 driver supports three devices, the DT compatible strings
and I2C IDs should enumerate these specifically rather than using a
wildcard so that we don't collide with anything incompatible in the
same ID range in the future and so that we can handle any software
visible differences between the variants we find.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20201215132024.13356-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add PM8350 and PM8350C compatibles for these PMICs found in some
Qualcomm platforms.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201203071244.2652297-1-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Update bindings for the Dialog Semiconductor DA9121 voltage regulator to
add device variants.
Because several variants have multiple regulators, and to regard potential
to add GPIO support in future, the 'regulators' sub-node is added,
following the precedent set by other multi-regulator devices, including
the DA9211 family. This breaks compatibility with the original submission
by Vincent Whitchurch - but as this is still in for-next, the alignment
could be made before upstreaming occurs.
Signed-off-by: Adam Ward <Adam.Ward.opensource@diasemi.com>
Link: https://lore.kernel.org/r/0606d3ded5fef4c38760246146f197db4ce3a374.1606755367.git.Adam.Ward.opensource@diasemi.com
Signed-off-by: Mark Brown <broonie@kernel.org>
RFC for adding a support for typical voltage scaling connection
In few occasions there has been a need to scale the voltage output
from bucks on BD71837. Usually this is done when buck8 is used to
power specific GPU which can utilize voltages down to 0.7V. As lowest
the buck8 on BD71837 can go is 0.8V, and external connection is used to
scale the voltages.
The BD71837, BD71847 and BD71850 bucks can be adjusted by pulling up the
feedback pin using suitable voltage/resistors.
|---------------|
| buck 8 |-------+----->Vout
| | |
|---------------| |
| |
| |
+-------+--R2----+
|
R1
|
V FB-pull-up
This will scale the voltage as follows:
- Vout_o = Vo - (Vpu - Vo)*R2/R1
- Linear_step = step_orig*(R1+R2)/R1
where:
Vout_o is adjusted voltage output at vsel reg value 0
Vo is original voltage output at vsel reg value 0
Vpu is the pull-up voltage V FB-pull-up in the picture
R1 and R2 are resistor values.
>From HW point of view this does not need to be limited to buck 8. This
connection can be used to adjust output from any of the bucks on
BD71837/47/50.
As this seems to be a 'de-facto' way to scale the voltages on BD71837 it
might be a good idea to support computing the new voltage ranges for
bucks based on the V-pull-up and resistor R1/R2 values given from
device-tree. This allows describing the external HW connection using DT
to correctly scale the voltages.
This RFC uses "rohm,feedback-pull-up-r1-ohms" and
"rohm,feedback-pull-up-r2-ohms" to provide the resistor values - but
these names (without the picture) might not be too descriptive. I am
grateful for all suggestions as better and more descriptive names.
This patch series is an RFC because this connection feels somewhat
"hacky". OTOH - when hack becomes widely used, it is less of an hack and
more of a standard - and occasionally supporting HW hacks using SW may
benefit us all, right? :)
The other thing some projects do is allowing the change of BD71837 buck8
voltages when buck8 is enabled. This however will introduce voltage
spikes as buck8 was not originally designed for this. The specific HW
platform must be evaluated to be able to tolerate these spikes. Thus
this patch series does not support buck8 voltage changes when buck8 is
enabled. I wonder if this should be allowed per some config option(?) I
don't want to help people frying their boards... Opinions? Is there
suggested way of allowing this type of features at own risk? Config or
even Some #ifdef which is not listed in Kconfig? Device-tree property?
If you have (good) suggestions I could add the optional (non default)
DVS support for non DVS bucks on BD71837.
Matti Vaittinen (3):
dt-bindings: regulator: BD71837 support commonly used feedback
connection
dt-bindings: regulator: BD71847 support commonly used feedback
connection
regulator: bd718x7: Support external connection to scale voltages
.../regulator/rohm,bd71837-regulator.yaml | 48 +++++
.../regulator/rohm,bd71847-regulator.yaml | 49 ++++++
drivers/regulator/bd718x7-regulator.c | 164 +++++++++++++++++-
3 files changed, 254 insertions(+), 7 deletions(-)
base-commit: 3cea11cd5e
--
2.21.3
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
The BD71847 buck output voltages are in a few cases scaled using external
connection which adds a pull-up to regulator feedback pin. This connection
will adjust output voltage from regulator in a deterministic way.
Add support for describing this HW connection so that driver can adjust
voltage ranges accordingly.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/9b6b3d8233071d478f7d1e93b498f5a2141941e6.1604994184.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The BD71837 buck output voltages are in a few cases scaled using external
connection which adds a pull-up to regulator feedback pin. This connection
will adjust output voltage from regulator in a deterministic way.
Add support for describing this HW connection so that driver can adjust
voltage ranges accordingly.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/9959924313db7c7165598604f9a07bf227f471a8.1604994184.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There's no $ref at the top level so use additionalProperties instead of
unevaluatedProperties.
This fixes the following warning with the latest dtschema:
Documentation/devicetree/bindings/regulator/dlg,da9121.yaml:
'additionalProperties' is a required property
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20201109085438.16230-1-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Another round of wack-a-mole. The json-schema default is additional
unknown properties are allowed, but for DT all properties should be
defined.
Signed-off-by: Rob Herring <robh@kernel.org>
Define bindings for fixed regulator using power domain performance state
to enable/disable corresponding regulator.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201023131925.334864-2-dmitry.baryshkov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
- Update dtc to upstream version v1.6.0-31-gcbca977ea121
- dtx_diff help text reformatting
- Speed-up validation time for binding and dtb checks using json for
intermediate files
- Add support for running yamllint on DT schema files
- Remove old booting-without-of.rst
- Extend the example schema to address common issues
- Cleanup handling of additionalProperties/unevaluatedProperties
- Ensure all DSI controller schemas reference dsi-controller.yaml
- Vendor prefixes for Zealz, Wandbord/Technexion, Embest RIoT, Rex, DFI,
and Cisco Meraki
- Convert at25, SPMI bus, TI hwlock, HiSilicon Hi3660 USB3 PHY, Arm
SP805 watchdog, Arm SP804, and Samsung 11-pin USB connector to DT
schema
- Convert HiSilicon SoC and syscon bindings to DT schema
- Convert SiFive Risc-V L2 cache, PLIC, PRCI, and PWM to DT schema
- Convert i.MX bindings for w1, crypto, rng, SIM, PM, DDR,
SATA, vf610 GPIO, and UART to DT schema
- Add i.MX 8M compatible strings
- Add LM81 and DS1780 as trivial devices
- Various missing properties added to fix dtb validation warnings
-----BEGIN PGP SIGNATURE-----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=gL4K
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Update dtc to upstream version v1.6.0-31-gcbca977ea121
- dtx_diff help text reformatting
- Speed-up validation time for binding and dtb checks using json for
intermediate files
- Add support for running yamllint on DT schema files
- Remove old booting-without-of.rst
- Extend the example schema to address common issues
- Cleanup handling of additionalProperties/unevaluatedProperties
- Ensure all DSI controller schemas reference dsi-controller.yaml
- Vendor prefixes for Zealz, Wandbord/Technexion, Embest RIoT, Rex,
DFI, and Cisco Meraki
- Convert at25, SPMI bus, TI hwlock, HiSilicon Hi3660 USB3 PHY, Arm
SP805 watchdog, Arm SP804, and Samsung 11-pin USB connector to DT
schema
- Convert HiSilicon SoC and syscon bindings to DT schema
- Convert SiFive Risc-V L2 cache, PLIC, PRCI, and PWM to DT schema
- Convert i.MX bindings for w1, crypto, rng, SIM, PM, DDR, SATA, vf610
GPIO, and UART to DT schema
- Add i.MX 8M compatible strings
- Add LM81 and DS1780 as trivial devices
- Various missing properties added to fix dtb validation warnings
* tag 'devicetree-for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (111 commits)
dt-bindings: misc: explicitly add #address-cells for slave mode
spi: dt-bindings: spi-controller: explicitly require #address-cells=<0> for slave mode
dt: Remove booting-without-of.rst
dt-bindings: update usb-c-connector example
dt-bindings: arm: hisilicon: add missing properties into cpuctrl.yaml
dt-bindings: arm: hisilicon: add missing properties into sysctrl.yaml
dt-bindings: pwm: imx: document i.MX compatibles
scripts/dtc: Update to upstream version v1.6.0-31-gcbca977ea121
dt-bindings: Add running yamllint to dt_binding_check
dt-bindings: powerpc: Add a schema for the 'sleep' property
dt-bindings: pinctrl: sirf: Fix typo abitrary
dt-bindings: pinctrl: qcom: Fix typo abitrary
dt-bindings: Explicitly allow additional properties in common schemas
dt-bindings: Use 'additionalProperties' instead of 'unevaluatedProperties'
dt-bindings: Add missing 'unevaluatedProperties'
Docs: Fixing spelling errors in Documentation/devicetree/bindings/
dt-bindings: arm: hisilicon: convert Hi6220 domain controller bindings to json-schema
dt-bindings: riscv: convert pwm bindings to json-schema
dt-bindings: riscv: convert plic bindings to json-schema
dt-bindings: fu540: prci: convert PRCI bindings to json-schema
...
In order to add meta-schema checks for additional/unevaluatedProperties
being present, all schema need to make this explicit. As common/shared
schema are included by other schemas, they should always allow for
additionalProperties.
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201005183830.486085-5-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
In cases where we don't reference another schema, 'additionalProperties'
can be used instead. This is preferred for now as 'unevaluatedProperties'
support isn't implemented yet.
In a few cases, this means adding some missing property definitions of
which most are for SPI bus properties. 'unevaluatedProperties' is not going
to work for the SPI bus properties anyways as they are evaluated from the
parent node, not the SPI child node.
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201005183830.486085-3-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
This doesn't yet do anything in the tools, but make it explicit so we can
check either 'unevaluatedProperties' or 'additionalProperties' is present
in schemas.
'unevaluatedProperties' is appropriate when including another schema (via
'$ref') and all possible properties and/or child nodes are not
explicitly listed in the schema with the '$ref'.
This is in preparation to add a meta-schema to check for missing
'unevaluatedProperties' or 'additionalProperties'. This has been a
constant source of review issues.
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20201005183830.486085-2-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
The PM660 and PM660L combo is found on boards featuring the
SDM630, SDM636, SDM660 (and SDA variants) and it is used to
give power to practically everything, from core to peripherals.
Document the SMD-RPM regulator entries for both.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20200926125549.13191-8-kholk11@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The PM660 and PM660L combo is found on boards featuring the
SDM630, SDM636, SDM660 (and SDA variants) and it is used to
give power to practically everything, from core to peripherals.
Document the SPMI regulator bindings for both.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20200926125549.13191-5-kholk11@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
1. Add vendor suffix to all proprietary properties.
2. Fix typo.
3. Change lsw to normal property, not pattern property.
4. Due to item 1, modify source code for property parsing.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1601460480-4259-1-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial support for ROHM BD9576MUF and BD9573MUF PMICs.
These PMICs are primarily intended to be used to power the R-Car family
processors. BD9576MUF includes some additional safety features the
BD9573MUF does not have. This initial version of drivers does not
utilize these features and for now the SW behaviour is identical.
Please note that this version of drivers is only tested on BD9576MUF
but according to the data-sheets the relevant parts of registers should
be same so drivers should also work on BD9573MUF.
This patch series includes MFD, watchdog and regulator drivers with
basic functionality such as:
- Enabling and pinging the watchdog
- configuring watchog timeout / window from device-tree
- reading regulator states/voltages
- enabling/disabling VOUT1 (VD50) when control mode B is used.
This patch series does not bring interrupt support. BD9576MUF and BD9573MUF
are designed to keep the IRQ line low for whole duration of error
condition. IRQ can't be 'acked'. So proper IRQ support would require
some IRQ limiter implementation (delayed unmask?) in order to not hog
the CPU.
---
Matti Vaittinen (6):
dt_bindings: mfd: Add ROHM BD9576MUF and BD9573MUF PMICs
dt_bindings: regulator: Add ROHM BD9576MUF and BD9573MUF PMICs
mfd: Support ROHM BD9576MUF and BD9573MUF
wdt: Support wdt on ROHM BD9576MUF and BD9573MUF
regulator: Support ROHM BD9576MUF and BD9573MUF
MAINTAINERS: Add ROHM BD9576MUF and BD9573MUF drivers
.../bindings/mfd/rohm,bd9576-pmic.yaml | 129 +++++++
.../regulator/rohm,bd9576-regulator.yaml | 33 ++
MAINTAINERS | 4 +
drivers/mfd/Kconfig | 11 +
drivers/mfd/Makefile | 1 +
drivers/mfd/rohm-bd9576.c | 130 +++++++
drivers/regulator/Kconfig | 10 +
drivers/regulator/Makefile | 1 +
drivers/regulator/bd9576-regulator.c | 337 ++++++++++++++++++
drivers/watchdog/Kconfig | 13 +
drivers/watchdog/Makefile | 1 +
drivers/watchdog/bd9576_wdt.c | 295 +++++++++++++++
include/linux/mfd/rohm-bd957x.h | 61 ++++
include/linux/mfd/rohm-generic.h | 2 +
14 files changed, 1028 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd9576-pmic.yaml
create mode 100644 Documentation/devicetree/bindings/regulator/rohm,bd9576-regulator.yaml
create mode 100644 drivers/mfd/rohm-bd9576.c
create mode 100644 drivers/regulator/bd9576-regulator.c
create mode 100644 drivers/watchdog/bd9576_wdt.c
create mode 100644 include/linux/mfd/rohm-bd957x.h
base-commit: f4d51dffc6
--
2.21.0
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
Convert the mp886x binding to DT schema format using json-schema.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200827150640.267f6edc@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
The BD718(37/47/50) regulator enable states can be controlled either by SW
or by PMIC internal state machine.
On some systems mixture of SW and HW state machine controlled regulators is
needed.
Specifically, some SoCs signal SUSPEND state change to PMIC via
STBY_REQ line. Now there are setups that expect certain regulators then to
be disabled (by PMIC state machine) while other regulators should stay
enabled (regardless of HW state => SW control required).
Add a new device-tree property "rohm,no-regulator-enable-control" which can
be used to leave regulator(s) under HW state machine control.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/51022c60412297ad9b22501452d60ba2dce38d2e.1599029334.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The BD718(37/47/50) regulator enable states can be controlled either by SW
or by PMIC internal state machine.
On some systems mixture of SW and HW state machine controlled regulators is
needed.
Specifically, some SoCs signal SUSPEND state change to PMIC via
STBY_REQ line. Now there are setups that expect certain regulators then to
be disabled (by PMIC state machine) while other regulators should stay
enabled (regardless of HW state => SW control required).
Add a new device-tree property "rohm,no-regulator-enable-control" which can
be used to leave regulator(s) under HW state machine control.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/9ff1104579093e7977944be769d625b9e33bc663.1599029334.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As Rob suggested, use the "mps,switch-frequency-hz" instead of the
"mps,switch-frequency" for switch frequency. Fortunately, the switch
frequency support isn't released, so we can modify it now without
any concern.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200824102402.4047fa5f@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Jisheng Zhang <Jisheng.Zhang@synaptics.com>:
From: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
This is to improve the mp886x regulator driver support.
patch1 implments .set_ramp_delay
patch2 and patch3 support the switch freq setting
patch4 converts dt binding to json-schema
Since v2:
- put any schema conversions at the end of the series as Mark
suggested.
Jisheng Zhang (4):
regulator: mp886x: implement set_ramp_delay
dt-bindings: regulator: mp886x: support mps,switch-frequency
regulator: mp886x: support setting switch freq
dt-bindings: regulator: Convert mp886x to json-schema
.../devicetree/bindings/regulator/mp886x.txt | 27 -----
.../bindings/regulator/mps,mp886x.yaml | 58 ++++++++++
drivers/regulator/mp886x.c | 109 +++++++++++++++++-
3 files changed, 164 insertions(+), 30 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/regulator/mp886x.txt
create mode 100644 Documentation/devicetree/bindings/regulator/mps,mp886x.yaml
--
2.28.0.rc1
Convert the sy8824x binding to DT schema format using json-schema.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200803144436.5d2b7e54@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Add DT bindings for RaspberryPi 7" display ATTINY88-based
regulator/backlight controller, this one is used in the
Raspberry Pi 7" touchscreen display unit.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Brown <broonie@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: devicetree@vger.kernel.org
To: dri-devel@lists.freedesktop.org
Link: https://lore.kernel.org/r/20200809105938.6388-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Both MP8867 and MP8869 support different switch frequency.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200729130952.260671f1@xhacker
Signed-off-by: Mark Brown <broonie@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200719200623.61524-1-grandmaster@al2klimov.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding the devicetree binding for labibb regulator.
[sumits: cleanup as per review comments and update to yaml]
Signed-off-by: Nisha Kumari <nishakumari@codeaurora.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200622124110.20971-3-sumit.semwal@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This patchset adds support for being able to change regulator modes for
the mt6397 regulator. This is needed to allow the voltage scaling
support in the MT8173 SoC to be used on the elm (Acer Chromebook R13)
and hana (several Lenovo Chromebooks) devices.
Without a of_map_mode implementation, the regulator-allowed-modes
devicetree field is skipped, and attempting to change the regulator mode
results in an error:
[ 1.439165] vpca15: mode operation not allowed
Changes in v2:
- Introduce constants in dt-bindings
- Improve conditional readability
Anand K Mistry (4):
regulator: mt6397: Move buck modes into header file
dt-bindings: regulator: mt6397: Document valid modes
regulator: mt6397: Implement of_map_mode
arm64: dts: mediatek: Update allowed mt6397 regulator modes for elm
boards
.../bindings/regulator/mt6397-regulator.txt | 3 +++
arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi | 4 +++-
drivers/regulator/mt6397-regulator.c | 17 ++++++++++++++---
.../regulator/mediatek,mt6397-regulator.h | 15 +++++++++++++++
4 files changed, 35 insertions(+), 4 deletions(-)
create mode 100644 include/dt-bindings/regulator/mediatek,mt6397-regulator.h
--
2.27.0.212.ge8ba1cc988-goog
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
This patchset adds support for being able to change regulator modes for
the da9211 regulator. This is needed to allow the voltage scaling
support in the MT8173 SoC to be used in the elm (Acer Chromebook R13)
and hana (several Lenovo Chromebooks) devices.
Anand K Mistry (4):
regulator: da9211: Move buck modes into header file
dt-bindings: regulator: da9211: Document allowed modes
regulator: da9211: Implement of_map_mode
arm64: dts: mediatek: Update allowed regulator modes for elm boards
.../devicetree/bindings/regulator/da9211.txt | 4 +++
arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi | 4 ++-
drivers/regulator/da9211-regulator.c | 30 +++++++++++++++----
.../regulator/dlg,da9211-regulator.h | 16 ++++++++++
4 files changed, 47 insertions(+), 7 deletions(-)
create mode 100644 include/dt-bindings/regulator/dlg,da9211-regulator.h
--
2.27.0.212.ge8ba1cc988-goog
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Changes in v4:
- Modified qcom,pmic-typec binding to include the SS mux and the DRD remote
endpoint nodes underneath port@1, which is assigned to the SSUSB path
according to usb-connector
- Added usb-connector reference to the typec dt-binding
- Added tags to the usb type c and vbus nodes
- Removed "qcom" tags from type c and vbus nodes
- Modified Kconfig module name, and removed module alias from the typec driver
Changes in v3:
- Fix driver reference to match driver name in Kconfig for
qcom_usb_vbus-regulator.c
- Utilize regulator bitmap helpers for enable, disable and is enabled calls in
qcom_usb_vbus-regulator.c
- Use of_get_regulator_init_data() to initialize regulator init data, and to
set constraints in qcom_usb_vbus-regulator.c
- Remove the need for a local device structure in the vbus regulator driver
Changes in v2:
- Use devm_kzalloc() in qcom_pmic_typec_probe()
- Add checks to make sure return value of typec_find_port_power_role() is
valid
- Added a VBUS output regulator driver, which will be used by the PMIC USB
type c driver to enable/disable the source
- Added logic to control vbus source from the PMIC type c driver when
UFP/DFP is detected
- Added dt-binding for this new regulator driver
- Fixed Kconfig typec notation to match others
- Leave type C block disabled until enabled by a platform DTS
Add the required drivers for implementing type C orientation and role
detection using the Qualcomm PMIC. Currently, PMICs such as the PM8150B
have an integrated type C block, which can be utilized for this. This
series adds the dt-binding, PMIC type C driver, and DTS nodes.
The PMIC type C driver will register itself as a type C port w/ a
registered type C switch for orientation, and will fetch a USB role switch
handle for the role notifications. It will also have the ability to enable
the VBUS output to any connected devices based on if the device is behaving
as a UFP or DFP.
Wesley Cheng (6):
usb: typec: Add QCOM PMIC typec detection driver
dt-bindings: usb: Add Qualcomm PMIC type C controller dt-binding
arm64: boot: dts: qcom: pm8150b: Add node for USB type C block
regulator: Add support for QCOM PMIC VBUS booster
dt-bindings: regulator: Add dt-binding for QCOM PMIC VBUS output
regulator
arm64: boot: dts: qcom: pm8150b: Add DTS node for PMIC VBUS booster
.../regulator/qcom,usb-vbus-regulator.yaml | 41 +++
.../bindings/usb/qcom,pmic-typec.yaml | 113 +++++++
arch/arm64/boot/dts/qcom/pm8150b.dtsi | 13 +
arch/arm64/boot/dts/qcom/sm8150-mtp.dts | 4 +
drivers/regulator/Kconfig | 10 +
drivers/regulator/Makefile | 1 +
drivers/regulator/qcom_usb_vbus-regulator.c | 97 ++++++
drivers/usb/typec/Kconfig | 12 +
drivers/usb/typec/Makefile | 1 +
drivers/usb/typec/qcom-pmic-typec.c | 275 ++++++++++++++++++
10 files changed, 567 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/qcom,usb-vbus-regulator.yaml
create mode 100644 Documentation/devicetree/bindings/usb/qcom,pmic-typec.yaml
create mode 100644 drivers/regulator/qcom_usb_vbus-regulator.c
create mode 100644 drivers/usb/typec/qcom-pmic-typec.c
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
This describes how to enable the Qualcomm PMIC VBUS booster used for
providing power to connected USB peripherals when the USB role is host
mode. The driver itself will register the vbus_usb regulator, so that
external drivers can utilize the enable/disable regulator APIs.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20200626185516.18018-6-wcheng@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for controlling voltage regulator that is connected and
controlled by ChromeOS EC. Kernel controls these regulators through
newly added EC host commands.
Changes from v5:
* Move new host command to a separate patch.
* Use devm_regulator_register.
* Address review comments.
Changes from v4:
* Change compatible name from regulator-cros-ec to cros-ec-regulator.
Changes from v3:
* Fix dt bindings file name.
* Remove check around CONFIG_OF in driver.
* Add new host commands to cros_ec_trace.
* Address review comments.
Changes from v2:
* Add 'depends on OF' to Kconfig.
* Add Kconfig description about compiling as module.
Changes from v1:
* Change compatible string to google,regulator-cros-ec.
* Use reg property in device tree.
* Change license for dt binding according to checkpatch.pl.
* Address comments on code styles.
Pi-Hsun Shih (3):
dt-bindings: regulator: Add DT binding for cros-ec-regulator
platform/chrome: cros_ec: Add command for regulator control.
regulator: Add driver for cros-ec-regulator
.../regulator/google,cros-ec-regulator.yaml | 51 ++++
drivers/platform/chrome/cros_ec_trace.c | 5 +
drivers/regulator/Kconfig | 10 +
drivers/regulator/Makefile | 1 +
drivers/regulator/cros-ec-regulator.c | 257 ++++++++++++++++++
.../linux/platform_data/cros_ec_commands.h | 82 ++++++
6 files changed, 406 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/google,cros-ec-regulator.yaml
create mode 100644 drivers/regulator/cros-ec-regulator.c
base-commit: b791d1bdf9
--
2.27.0.290.gba653c62da-goog
Add DT binding documentation for cros-ec-regulator, a voltage regulator
controlled by ChromeOS EC.
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20200612040526.192878-2-pihsun@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Another round of 'allOf' removals that came in this cycle.
json-schema versions draft7 and earlier have a weird behavior in that
any keywords combined with a '$ref' are ignored (silently). The correct
form was to put a '$ref' under an 'allOf'. This behavior is now changed
in the 2019-09 json-schema spec and '$ref' can be mixed with other
keywords. The json-schema library doesn't yet support this, but the
tooling now does a fixup for this and either way works.
This has been a constant source of review comments, so let's change this
treewide so everyone copies the simpler syntax.
Signed-off-by: Rob Herring <robh@kernel.org>
- Convert various DT (non-binding) doc files to ReST
- Various improvements to device link code
- Fix __of_attach_node_sysfs refcounting bug
- Add support for 'memory-region-names' with reserved-memory binding
- Vendor prefixes for Protonic Holland, BeagleBoard.org, Alps, Check
Point, Würth Elektronik, U-Boot, Vaisala, Baikal Electronics, Shanghai
Awinic Technology Co., MikroTik, Silex Insight
- A bunch more binding conversions to DT schema. Only 3K to go.
- Add a minimum version check for schema tools
- Treewide dropping of 'allOf' usage with schema references. Not needed
in new json-schema spec.
- Some formatting clean-ups of schemas
-----BEGIN PGP SIGNATURE-----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=/MDi
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Convert various DT (non-binding) doc files to ReST
- Various improvements to device link code
- Fix __of_attach_node_sysfs refcounting bug
- Add support for 'memory-region-names' with reserved-memory binding
- Vendor prefixes for Protonic Holland, BeagleBoard.org, Alps, Check
Point, Würth Elektronik, U-Boot, Vaisala, Baikal Electronics,
Shanghai Awinic Technology Co., MikroTik, Silex Insight
- A bunch more binding conversions to DT schema. Only 3K to go.
- Add a minimum version check for schema tools
- Treewide dropping of 'allOf' usage with schema references. Not needed
in new json-schema spec.
- Some formatting clean-ups of schemas
* tag 'devicetree-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (194 commits)
dt-bindings: clock: Add documentation for X1830 bindings.
dt-bindings: mailbox: Convert imx mu to json-schema
dt-bindings: power: Convert imx gpcv2 to json-schema
dt-bindings: power: Convert imx gpc to json-schema
dt-bindings: Merge gpio-usb-b-connector with usb-connector
dt-bindings: timer: renesas: cmt: Convert to json-schema
dt-bindings: clock: Convert i.MX8QXP LPCG to json-schema
dt-bindings: timer: Convert i.MX GPT to json-schema
dt-bindings: thermal: rcar-thermal: Add device tree support for r8a7742
dt-bindings: serial: Add binding for UART pin swap
dt-bindings: geni-se: Add interconnect binding for GENI QUP
dt-bindings: geni-se: Convert QUP geni-se bindings to YAML
dt-bindings: vendor-prefixes: Add Silex Insight vendor prefix
dt-bindings: input: touchscreen: edt-ft5x06: change reg property
dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver
dt-bindings: timer: renesas: mtu2: Convert to json-schema
of/fdt: Remove redundant kbasename function call
dt-bindings: clock: Convert i.MX1 clock to json-schema
dt-bindings: clock: Convert i.MX21 clock to json-schema
dt-bindings: clock: Convert i.MX25 clock to json-schema
...
Series extracts a "linear ranges" helper out of the regulator
framework. Linear ranges helper is intended to help converting
real-world values to register values when conversion is linear. I
suspect this is useful also for power subsystem and possibly for clk.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl61lKwTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0HxeB/9dblIbC+28MvcEHXCcYBZBouOnrM8E
bIOMXkgEj1uL78ozOm7tMCgEpaKgv6BHdDuClCBvjbr0uOtAi0qUiv0IBotuVrdo
lq73l8l7OPz6TFFKIt8WsgwKnzdkuQC08+qrZasAdluRQnqnmkU2tvl2y9zaaaR4
6hGw+Nwx/pgeCXCa3pu+rCYwA7g0Tf8a6DDC6LyQWZameBJ1ey/YDjhJEeSmY7P7
306zs8YVxHhQMLUQ5T7DA6r/KWMNkO1SOueCqTjxWZc/XamGEcbsZG1cWrAnkoE2
VKLXBtYC75coNxIiu8ZxnQwLLdz1EQPdtg0qmzSjXJ68QjbWWzf4K1ra
=LG9G
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl61lPUTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0GuGB/9kDFxKo0DWsH6tqZGS/retk0ddT+4B
mnkkZGvoKkkDe1lh84vRbrPHhiI9LIXaj3lFgzyYeTuAi9tb77mPNnYIPLDye7bO
OvgJgovo4tK3dUVSUFatvOhuAMSZLyN2WjWRX+YeHMd1nNZSHxEz0CuG3npNtuKa
KoZd0Dfom4ds66qDlWdfonFhMJbMvQbEs4BhnfdvpD/soylyDB+29SHlhTBv8+UC
I7BNzsmVDlp/JyrX3yJbuTum9wbPaMLcyL96EbvRykmTywz5FXudffqzPfPnoQxT
rbN5DfwKsnySToUYDfp9dcIMyTF0/MtneaeBMRu2NIkpMmnicvExNrbU
=/+DM
-----END PGP SIGNATURE-----
Merge tag 'linear-ranges-lib' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-5.8
lib: Add linear ranges helper library and start using it
Series extracts a "linear ranges" helper out of the regulator
framework. Linear ranges helper is intended to help converting
real-world values to register values when conversion is linear. I
suspect this is useful also for power subsystem and possibly for clk.
json-schema versions draft7 and earlier have a weird behavior in that
any keywords combined with a '$ref' are ignored (silently). The correct
form was to put a '$ref' under an 'allOf'. This behavior is now changed
in the 2019-09 json-schema spec and '$ref' can be mixed with other
keywords. The json-schema library doesn't yet support this, but the
tooling now does a fixup for this and either way works.
This has been a constant source of review comments, so let's change this
treewide so everyone copies the simpler syntax.
Scripted with ruamel.yaml with some manual fixups. Some minor whitespace
changes from the script.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for I2C
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for-iio
Reviewed-by: Stephen Boyd <sboyd@kernel.org> # clock
Signed-off-by: Rob Herring <robh@kernel.org>
In this particular location additionalProperties actually declares a property
named `additionalProperties` instead of specifying there should be no other
properties.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Link: https://lore.kernel.org/r/20200425125335.2674534-1-iskren.chernev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There's several cases of json-schema 'additionalProperties' at the wrong
indentation level which has the effect of making them DT properties. This
is harmless, but let's fix them so a meta-schema check for this can be
added.
In all the cases, either the 'additionalProperties' was extra or doesn't
work because there's a $ref to more properties. In the latter case, we
can use 'unevaluatedProperties' instead.
Reported-by: Iskren Chernev <iskren.chernev@gmail.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Saravanan Sekar <sravanhome@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
- Add support for IQS620A/621/622/624/625 Azoteq IQS62X Sensors
- New Device Support
- Add support for ADC, IRQ, Regulator, RTC and WDT to Ricoh RN5T618 PMIC
- Add support for Comet Lake to Intel LPSS
- New Functionality
- Add support for Charger Detection to Spreadtrum SC27xx PMICs
- Add support for Interrupt Polarity to Dialog Semi DA9062/61 PMIC
- Add ACPI enumeration support to Diolan DLN2 USB Adaptor
- Fix-ups
- Device Tree; iqs62x, rn5t618, cros_ec_dev, stm32-lptimer, rohm,bd71837, rohm,bd71847
- I2C registration; rn5t618
- Kconfig; MFD_CPCAP, AB8500_CORE, MFD_WM8994, MFD_WM97xx, MFD_STPMIC1
- Use flexible-array members; omap-usb-tll, qcom-pm8xxx
- Remove unnecessary casts; omap-usb-host, omap-usb-tll
- Power (suspend/resume/poweroff) enhancements; rk808
- Improve error/sanity checking; dln2
- Use snprintf(); aat2870-core
- Bug Fixes
- Fix PCI IDs; intel-lpss-pci
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEdrbJNaO+IJqU8IdIUa+KL4f8d2EFAl6MSwsACgkQUa+KL4f8
d2GklhAAk1e0tYu1w4yS0IE40mReDk5ycOE1O8Q75qWw5Af2dK48qvSHGDwaU4ES
WNYZ3Mr/OUrvd+/XU8EXI6NXAi9W75ye2J2KmmDDL6yXnDuHbzBZF8ifEtXQKSOp
rElzCJVnXehpjSfwa4cp5f1Msox/rFg1Kpmaas48j8U2JYCmn51GsQCCG6qMIx2i
0ZvXNZuz+eTY3V7l6pRLfTYqwR8E5Y11ryWJaeliyDcVpUlZaykiXuxD7pbqLjJo
8v9ISm67rzf6X5zmi6YhdvpIAzpomdRaaxHfVDkeCKqDgpuWGiq0xXA86vDKwjah
qVx6rK/wg4YM5uSEomxIgVj9uvvLSytDqvRlPe7vFKgkR0Xhl5SdkiwadI4P9zkr
zrRGNRAUHsZ4ZrlObD0QJWOQYnIg5oCmRouRKcHtQVZYP3rSdRz/1oC6FN8LVqUw
3NfLB/S6uBCJ3uahckrgnjQughnvmsAzlflcNV2t+P8di8Cwyh2A5N9qkT/oI67o
Xf7NODSdu0JzzTgsM+EJ2JphSLMYaekWs06qAXyibPrrS2SoThE79igCmNOkyyR7
obJfN2SM5k4LkhMGlYbPfbRT2Hoa+9OJozBe3WgiW3kwTdFVB9aen2U230tHplbB
g/NuVS+PrReR5lfzT+O8dodH7lj5/GhmGsapdguFVhXYIE+2CMg=
=hJ2o
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull mfd updates from Lee Jones:
"New Drivers:
- Add support for IQS620A/621/622/624/625 Azoteq IQS62X Sensors
New Device Support:
- Add support for ADC, IRQ, Regulator, RTC and WDT to Ricoh RN5T618 PMIC
- Add support for Comet Lake to Intel LPSS
New Functionality:
- Add support for Charger Detection to Spreadtrum SC27xx PMICs
- Add support for Interrupt Polarity to Dialog Semi DA9062/61 PMIC
- Add ACPI enumeration support to Diolan DLN2 USB Adaptor
Fix-ups:
- Device Tree; iqs62x, rn5t618, cros_ec_dev, stm32-lptimer, rohm,bd71837, rohm,bd71847
- I2C registration; rn5t618
- Kconfig; MFD_CPCAP, AB8500_CORE, MFD_WM8994, MFD_WM97xx, MFD_STPMIC1
- Use flexible-array members; omap-usb-tll, qcom-pm8xxx
- Remove unnecessary casts; omap-usb-host, omap-usb-tll
- Power (suspend/resume/poweroff) enhancements; rk808
- Improve error/sanity checking; dln2
- Use snprintf(); aat2870-core
Bug Fixes:
- Fix PCI IDs in intel-lpss-pci"
* tag 'mfd-next-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (33 commits)
mfd: intel-lpss: Fix Intel Elkhart Lake LPSS I2C input clock
mfd: aat2870: Use scnprintf() for avoiding potential buffer overflow
mfd: dln2: Allow to be enumerated via ACPI
mfd: da9062: Add support for interrupt polarity defined in device tree
dt-bindings: bd718x7: Yamlify and add BD71850
mfd: dln2: Fix sanity checking for endpoints
mfd: intel-lpss: Add Intel Comet Lake PCH-V PCI IDs
mfd: sc27xx: Add USB charger type detection support
dt-bindings: mfd: Document STM32 low power timer bindings
mfd: rk808: Convert RK805 to shutdown/suspend hooks
mfd: rk808: Reduce shutdown duplication
mfd: rk808: Stop using syscore ops
mfd: rk808: Ensure suspend/resume hooks always work
mfd: rk808: Always use poweroff when requested
mfd: omap: Remove useless cast for driver.name
mfd: Kconfig: Fix some misspelling of the word functionality
mfd: pm8xxx: Replace zero-length array with flexible-array member
mfd: omap-usb-tll: Replace zero-length array with flexible-array member
mfd: cpcap: Fix compile if MFD_CORE is not selected
mfd: cros_ec: Check DT node for usbpd-notify add
...
- Unit test for overlays with GPIO hogs
- Improve dma-ranges parsing to handle dma-ranges with multiple entries
- Update dtc to upstream version v1.6.0-2-g87a656ae5ff9
- Improve overlay error reporting
- Device link support for power-domains and hwlocks bindings
- Add vendor prefixes for Beacon, Topwise, ENE, Dell, SG Micro, Elida,
PocketBook, Xiaomi, Linutronix, OzzMaker, Waveshare Electronics, and
ITE Tech
- Add deprecated Marvell vendor prefix 'mrvl'
- A bunch of binding conversions to DT schema continues. Of note, the
common serial and USB connector bindings are converted.
- Add more Arm CPU compatibles
- Drop Mark Rutland as DT maintainer :(
-----BEGIN PGP SIGNATURE-----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=db/l
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Unit test for overlays with GPIO hogs
- Improve dma-ranges parsing to handle dma-ranges with multiple entries
- Update dtc to upstream version v1.6.0-2-g87a656ae5ff9
- Improve overlay error reporting
- Device link support for power-domains and hwlocks bindings
- Add vendor prefixes for Beacon, Topwise, ENE, Dell, SG Micro, Elida,
PocketBook, Xiaomi, Linutronix, OzzMaker, Waveshare Electronics, and
ITE Tech
- Add deprecated Marvell vendor prefix 'mrvl'
- A bunch of binding conversions to DT schema continues. Of note, the
common serial and USB connector bindings are converted.
- Add more Arm CPU compatibles
- Drop Mark Rutland as DT maintainer :(
* tag 'devicetree-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (106 commits)
MAINTAINERS: drop an old reference to stm32 pwm timers doc
MAINTAINERS: dt: update etnaviv file reference
dt-bindings: usb: dwc2: fix bindings for amlogic, meson-gxbb-usb
dt-bindings: uniphier-system-bus: fix warning in the example
dt-bindings: display: meson-vpu: fix indentation of reg-names' "items"
dt-bindings: iio: Fix adi, ltc2983 uint64-matrix schema constraints
dt-bindings: power: Fix example for power-domain
dt-bindings: arm: Add some constraints for PSCI nodes
of: some unittest overlays not untracked
of: gpio unittest kfree() wrong object
dt-bindings: phy: convert phy-rockchip-inno-usb2 bindings to yaml
dt-bindings: serial: sh-sci: Convert to json-schema
dt-bindings: serial: Document serialN aliases
dt-bindings: thermal: tsens: Set 'additionalProperties: false'
dt-bindings: thermal: tsens: Fix nvmem-cell-names schema
dt-bindings: vendor-prefixes: Add Beacon vendor prefix
dt-bindings: vendor-prefixes: Add Topwise
of: of_private.h: Replace zero-length array with flexible-array member
docs: dt: fix a broken reference to input.yaml
docs: dt: fix references to ap806-system-controller.txt
...
Setting 'additionalProperties: false' is frequently omitted, but is
important in order to check that there aren't extra undocumented
properties in a binding.
Ideally, we'd just add this automatically and make this the default, but
there's some cases where it doesn't work. For example, if a common
schema is referenced, then properties in the common schema aren't part
of what's considered for 'additionalProperties'. Also, sometimes there
are bus specific properties such as 'spi-max-frequency' that go into
bus child nodes, but aren't defined in the child node's schema.
So let's stick with the json-schema defined default and add
'additionalProperties: false' where needed. This will be a continual
review comment and game of wack-a-mole.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Stephen Boyd <sboyd@kernel.org> # clock
Acked-by: Lee Jones <lee.jones@linaro.org>
Convert ROHM bd71837 and bd71847 PMIC binding text docs to yaml. Split
the binding document to two separate documents (own documents for BD71837
and BD71847) as they have different amount of regulators. This way we can
better enforce the node name check for regulators. ROHM is also providing
BD71850 - which is almost identical to BD71847 - main difference is some
initial regulator states. The BD71850 can be driven by same driver and it
has same buck/LDO setup as BD71847 - add it to BD71847 binding document and
introduce compatible for it.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Numerous schemas are missing 'additionalProperties: false' statements which
ensures a binding doesn't have any extra undocumented properties or child
nodes. Fixing this reveals various missing properties, so let's fix all
those occurrences.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for-iio
Acked-by: Stephen Boyd <sboyd@kernel.org> # clock
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: dri-devel@lists.freedesktop.org
Cc: netdev@vger.kernel.org
Cc: Guillaume La Roque <glaroque@baylibre.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-iio@vger.kernel.org
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-clk@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: linux-amlogic@lists.infradead.org
Cc: linux-pm@vger.kernel.org
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-gpio@vger.kernel.org
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-media@vger.kernel.org
Cc: Lee Jones <lee.jones@linaro.org>
The pmi8994 is commonly found on MSM8996 based devices, such as the
Dragonboard 820c, where it supplies power to a number of LDOs on the
primary PMIC.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200324041424.518160-1-bjorn.andersson@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
MP8867 is an I2C-controlled adjustable voltage regulator made by
Monolithic Power Systems. The difference between MP8867 and MP8869
are:
1.If V_BOOT, the vref of MP8869 is fixed at 600mv while vref of MP8867
is determined by the I2C control.
2.For MP8867, when setting voltage, if the steps is within 5, we need
to manually set the GO_BIT to 0.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200316223100.37805b22@xhacker
Signed-off-by: Mark Brown <broonie@kernel.org>
The MP8869 from Monolithic Power Systems is a single output dc/dc
converter with voltage control over i2c.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200316222945.74ad34dd@xhacker
Signed-off-by: Mark Brown <broonie@kernel.org>
- Fixes for warnings introduced by hierarchical PSCI binding changes
- Fixes for broken doc references due to DT schema conversions
- Several grammar and typo fixes
- Fix a bunch of dtc warnings in examples
-----BEGIN PGP SIGNATURE-----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=sbhb
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-5.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
"Another batch of DT fixes. I think this should be the last of it, but
sending pull requests seems to cause people to send more fixes.
Summary:
- Fixes for warnings introduced by hierarchical PSCI binding changes
- Fixes for broken doc references due to DT schema conversions
- Several grammar and typo fixes
- Fix a bunch of dtc warnings in examples"
* tag 'devicetree-fixes-for-5.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: arm: Fixup the DT bindings for hierarchical PSCI states
dt-bindings: power: Extend nodename pattern for power-domain providers
MAINTAINERS: update ALLWINNER CPUFREQ DRIVER entry
dt-bindings: bus: Drop empty compatible string in example
dt-bindings: power: Convert domain-idle-states bindings to json-schema
dt-bindings: arm: Fix cpu compatibles in the hierarchical example for PSCI
dt-bindings: arm: Correct links to idle states definitions
dt-bindings: mfd: Fix typo in file name of twl-familly.txt
dt-bindings: mfd: tps65910: Improve grammar
dt-bindings: mfd: zii,rave-sp: Fix a typo ("onborad")
dt-bindings: arm: fsl: fix APF6Dev compatible
dt-bindings: Fix dtc warnings in examples
docs: dt: fix several broken doc references
docs: dt: fix several broken references due to renames
MAINTAINERS: clean up PCIE DRIVER FOR CAVIUM THUNDERX
This patch adds bindings for the Qualcomm IPQ4019 VQMMC SD LDO driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Message-Id: <20200122134023.1467806-1-robert.marko@sartura.hr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix all the warnings in the DT binding schema examples when built with
'W=1'. This is in preparation to make that the default for examples.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add device tree binding information for mp5416 regulator driver.
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200204110419.25933-2-sravanhome@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add device tree binding information for mpq7920 regulator driver.
Example bindings for mpq7920 are added.
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200123215338.11109-1-sravanhome@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit f5fa59a61e "regulator: bindings: add
document bindings for mpq7920" as Rob has a number of problems
with the use of DT schema.
Signed-off-by: Mark Brown <broonie@kernel.org>
Add device tree binding information for mpq7920 regulator driver.
Example bindings for mpq7920 are added.
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Link: https://lore.kernel.org/r/20200108131234.24128-3-sravanhome@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The MP8859 from Monolithic Power Systems is a single output dc/dc converter
with voltage control over i2c.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Link: https://lore.kernel.org/r/20200106211633.2882-5-m.reichl@fivetechno.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the stm32-pwr regulator binding to DT schema format using
json-schema.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191205161359.20755-1-p.paillet@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the STM32 regulator vrefbuf binding to DT schema format using json-schema
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
CC: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191122104536.20283-2-benjamin.gaignard@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the STM32 regulator booster binding to DT schema format using json-schema
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
CC: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191122104536.20283-1-benjamin.gaignard@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- DT schemas for PWM, syscon, power domains, SRAM, syscon-reboot,
syscon-poweroff, renesas-irqc, simple-pm-bus, renesas-bsc, pwm-rcar,
Renesas tpu, at24 eeprom, rtc-sh, Allwinner PS/2, sharp,ld-d5116z01b
panel, Arm SMMU, max77650, Meson CEC, Amlogic canvas and DWC3 glue,
Allwinner A10 mUSB and CAN, TI Davinci MDIO, QCom QCS404 interconnect,
Unisoc/Spreadtrum SoCs and UART
- Convert a bunch of Samsung bindings to DT schema
- Convert a bunch of ST stm32 bindings to DT schema
- Realtek and Exynos additions to Arm Mali bindings
- Fix schema errors in RiscV CPU schema
- Various schema fixes from improved meta-schema checks
- Improve the handling of 'dma-ranges' and in particular fix DMA mask
setup on PCI bridges
- Fix a memory leak in add_changeset_property() and DT unit tests.
- Several documentation improvements for schema validation
- Rework build rules to improve schema validation errors
- Color output for dtx_diff
-----BEGIN PGP SIGNATURE-----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=L6uq
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- DT schemas for PWM, syscon, power domains, SRAM, syscon-reboot,
syscon-poweroff, renesas-irqc, simple-pm-bus, renesas-bsc, pwm-rcar,
Renesas tpu, at24 eeprom, rtc-sh, Allwinner PS/2, sharp,ld-d5116z01b
panel, Arm SMMU, max77650, Meson CEC, Amlogic canvas and DWC3 glue,
Allwinner A10 mUSB and CAN, TI Davinci MDIO, QCom QCS404
interconnect, Unisoc/Spreadtrum SoCs and UART
- Convert a bunch of Samsung bindings to DT schema
- Convert a bunch of ST stm32 bindings to DT schema
- Realtek and Exynos additions to Arm Mali bindings
- Fix schema errors in RiscV CPU schema
- Various schema fixes from improved meta-schema checks
- Improve the handling of 'dma-ranges' and in particular fix DMA mask
setup on PCI bridges
- Fix a memory leak in add_changeset_property() and DT unit tests.
- Several documentation improvements for schema validation
- Rework build rules to improve schema validation errors
- Color output for dtx_diff
* tag 'devicetree-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (138 commits)
libfdt: define INT32_MAX and UINT32_MAX in libfdt_env.h
dt-bindings: arm: Remove leftover axentia.txt
of: unittest: fix memory leak in attach_node_and_children
of: overlay: add_changeset_property() memory leak
dt-bindings: interrupt-controller: arm,gic-v3: Add missing type to interrupt-partition-* nodes
dt-bindings: firmware: ixp4xx: Drop redundant minItems/maxItems
dt-bindings: power: Rename back power_domain.txt bindings to fix references
dt-bindings: i2c: stm32: Migrate i2c-stm32 documentation to yaml
dt-bindings: mtd: Convert stm32 fmc2-nand bindings to json-schema
dt-bindings: remoteproc: convert stm32-rproc to json-schema
dt-bindings: mailbox: convert stm32-ipcc to json-schema
dt-bindings: mfd: Convert stm32 low power timers bindings to json-schema
dt-bindings: interrupt-controller: Convert stm32-exti to json-schema
dt-bindings: crypto: Convert stm32 HASH bindings to json-schema
dt-bindings: rng: Convert stm32 RNG bindings to json-schema
dt-bindings: pwm: Convert Samsung PWM bindings to json-schema
dt-bindings: pwm: Convert PWM bindings to json-schema
dt-bindings: serial: Add a new compatible string for SC9863A
dt-bindings: serial: Convert sprd-uart to json-schema
dt-bindings: arm: Add bindings for Unisoc SC9863A
...
There is voltage coupling between three regulators on Tegra20 boards and
between two on Tegra30. The voltage coupling is a SoC-level feature and
thus it is mandatory and common for all of the Tegra boards.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When disabling a fixed regulator, it may take some time to let the
voltage drop to the expected value, such as zero. If not delay
enough time, the regulator might have been always enabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1572311875-22880-2-git-send-email-peng.fan@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the binding document for MAX77650 regulator module to YAML.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Regulator '*-supply' properties are always a single phandle, so
'maxItems: 1' or a $ref is not necessary. All that's needed is either
'true' or an optional 'description'. Following this clean-up, the
meta-schema will enforce this pattern.
There's one case in tree with 'innolux,n156bge-l21' having 2 phandles.
This appears to be a mistake or abuse of simple-panel as it's 2 different
voltage rails connected to 'power-supply'.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-iio@vger.kernel.org
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Signed-off-by: Rob Herring <robh@kernel.org>
This Power IC is used in combination with various PMIC combos,
generally found on boards with MSM8992, MSM8994, MSM8996,
MSM8956, MSM8976 and others, usually at address 0x5 on the SPMI
bus, and its usual usage is to provide power to the GPU and/or
to the CPU clusters (APC0/APC1).
Signed-off-by: Angelo G. Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20190921095043.62593-6-kholk11@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The PM8950 provides 6 SMPS regulators, of which 5 HFSMPS
and one FTSMPS2.5 (s5), and 23 LDOs.
Add these to the RPM regulator driver.
Signed-off-by: Angelo G. Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20190921095043.62593-4-kholk11@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The PM8950 has 5 HFSMPS, 1 FTSMPS2.5 (s5, controlling APC voltage)
and 23 LDO regulators.
Add the configuration for this chip.
Signed-off-by: Angelo G. Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20190921095043.62593-3-kholk11@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds the documentation to the compatible regulator-fixed-clock.
This binding is a special binding of regulator-fixed and adds the
ability to add a clock to regulator-fixed, so the regulator can be
enabled and disabled with that clock. If the special compatible
regulator-fixed-clock is used it is mandatory to supply a clock.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20190910062103.39641-4-philippe.schenker@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SY20276 is an I2C-controlled adjustable voltage regulator made by
Silergy Corp. The differences between SY8824C and SY20278 are
different regs for mode/enable.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190827163754.170cf130@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
SY20276 is an I2C-controlled adjustable voltage regulator made by
Silergy Corp. The differences between SY8824C and SY20276 are
different vsel_min, vsel_step, vsel_count and regs for mode/enable.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190827163650.47ed1213@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
SY8824E is an I2C-controlled adjustable voltage regulator made by
Silergy Corp. The only difference between SY8824C and SY8824E is the
vsel_min.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190827163505.361890af@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
SY8824C is an I2C-controlled adjustable voltage regulator made by
Silergy Corp.
Add its device tree binding.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190827163341.61df63a7@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Add documentation for act8865 regulator modes and suspend states.
Add active-semi,8865-regulator.h file for device tree binding constants
for act8865 regulators.
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Link: https://lore.kernel.org/r/1565721176-8955-3-git-send-email-raagjadav@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
During reset the VMMC regulator doesn't reach 0V and only drops to
1.8V, furthermore the pulse width is under 200us whereas the SD
specification expect 1ms.
For this 2 reasons being able to no reset at all the VMMC during warm
reset and keep the current voltage is a good workaround. The TWL6030
allows this but needs to be aware of it and this configuration should
also be shared with the bootloader.
This is the purpose of this new property: ti,retain-on-reset
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20190725094542.16547-2-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It helps to keep sorted order for compatibles and nodes, so sort them
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20190809073616.1235-1-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
- DT binding schema examples are now validated against the schemas.
Various examples are fixed due to that.
- Sync dtc with upstream version v1.5.0-30-g702c1b6c0e73
- Initial schemas for networking bindings. This includes ethernet, phy
and mdio common bindings with several Allwinner and stmmac converted
to the schema.
- Conversion of more Arm top-level SoC/board bindings to DT schema
- Conversion of PSCI binding to DT schema
- Rework Arm CPU schema to coexist with other CPU schemas
- Add a bunch of missing vendor prefixes and new ones for SoChip,
Sipeed, Kontron, B&R Industrial Automation GmbH, and Espressif
- Add Mediatek UART RX wakeup support to binding
- Add reset to ST UART binding
- Remove some Linuxisms from the endianness common-properties.txt
binding
- Make the flattened DT read-only after init
- Ignore disabled reserved memory nodes
- Clean-up some dead code in FDT functions
-----BEGIN PGP SIGNATURE-----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=Qpuw
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- DT binding schema examples are now validated against the schemas.
Various examples are fixed due to that.
- Sync dtc with upstream version v1.5.0-30-g702c1b6c0e73
- Initial schemas for networking bindings. This includes ethernet, phy
and mdio common bindings with several Allwinner and stmmac converted
to the schema.
- Conversion of more Arm top-level SoC/board bindings to DT schema
- Conversion of PSCI binding to DT schema
- Rework Arm CPU schema to coexist with other CPU schemas
- Add a bunch of missing vendor prefixes and new ones for SoChip,
Sipeed, Kontron, B&R Industrial Automation GmbH, and Espressif
- Add Mediatek UART RX wakeup support to binding
- Add reset to ST UART binding
- Remove some Linuxisms from the endianness common-properties.txt
binding
- Make the flattened DT read-only after init
- Ignore disabled reserved memory nodes
- Clean-up some dead code in FDT functions
* tag 'devicetree-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (56 commits)
dt-bindings: vendor-prefixes: add Sipeed
dt-bindings: vendor-prefixes: add SoChip
dt-bindings: 83xx-512x-pci: Drop cell-index property
dt-bindings: serial: add documentation for Rx in-band wakeup support
dt-bindings: arm: Convert RDA Micro board/soc bindings to json-schema
of: unittest: simplify getting the adapter of a client
of/fdt: pass early_init_dt_reserve_memory_arch() with bool type nomap
of/platform: Drop superfluous cast in of_device_make_bus_id()
dt-bindings: usb: ehci: Fix example warnings
dt-bindings: net: Use phy-mode instead of phy-connection-type
dt-bindings: simple-framebuffer: Add requirement for pipelines
dt-bindings: display: Fix simple-framebuffer example
dt-bindings: net: mdio: Add child nodes
dt-bindings: net: mdio: Add address and size cells
dt-bindings: net: mdio: Add a nodename pattern
dt-bindings: mtd: sunxi-nand: Drop 'maxItems' from child 'reg' property
dt-bindings: arm: Limit cpus schema to only check Arm 'cpu' nodes
dt-bindings: backlight: lm3630a: correct schema validation
dt-bindings: net: dwmac: Deprecate the PHY reset properties
dt-bindings: net: sun8i-emac: Convert the binding to a schemas
...
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
Document the 3.3V booster regulator embedded in stm32h7 and stm32mp1
devices, that can be used to supply ADC analog input switches.
It's controlled by using system configuration registers (SYSCFG).
Introduce two compatibles as the booster regulator is controlled by:
- a unique register/bit in STM32H7
- a set/clear register pair in STM32MP1
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PMS405 supports 5 SMPS and 13 LDO regulators.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the dt bindings for the PM8005 regulators which are usually used
for VDD of standalone blocks on a SoC like the GPU.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
"git diff" says:
\ No newline at end of file
after modifying the files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
Mostly due to x86 and acpi conversion, several documentation
links are still pointing to the old file. Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com>
Reviewed-by: Bhupesh Sharma <bhsharma@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Convert the max8660 binding to DT schema format using json-schema.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the gpio-regulator binding to DT schema format using
json-schema.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the common regulator binding to DT schema format. Note that all
the properties with standard unit suffixes have type checks already, so
only a description is necessary.
As fixed-regulator has already been converted, update the references in
it. Otherwise, keep regulator.txt with a reference to the schema to
avoid a bunch of treewide updates. regulator.txt can be removed when all
the regulator bindings are converted.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Arizona regulator drivers are now also used by the Cirrus Logic
Madera audio CODECs, update the binding document to link to the primary
binding document for these as well as the existing Arizona document.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add device tree binding information for slg51000 regulator driver.
Example bindings for SLG51000 are added.
Signed-off-by: Eric Jeong <eric.jeong.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document devicetree bindings for stm32mp1 pwr regulators.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reword the binding document to make it clear how the propeties work
and which properties affect which other properties.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Harald Geyer <harald@ccbib.org>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: linux-renesas-soc@vger.kernel.org
To: devicetree@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
LS3 has a selectable current limit.
Change units to microamp in the example.
Signed-off-by: Christian Hohnstaedt <Christian.Hohnstaedt@wago.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document device-tree settings of the load-switch LS2
in the tps65218 device.
Signed-off-by: Christian Hohnstaedt <Christian.Hohnstaedt@wago.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The FAN53526 differs from the FAN53555 only in that the mode bit in
VSEL0/VSEL1 is moved to the CONTROL register, the voltage selector mask
is extended by 1 bit and the step is different.
So extend the existing fan53555 driver to support FAN53526 as well.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for active discharge for USB power switches.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulator high pull down are enabled by default so remove support in the
driver.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The interrupt parent description is not needed as the parent is a parent
node with 'interrupt-controller' property.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add ROHM BD71837 / BD71847 specific device tree bindings for
controlling the PMIC shutdown/reset states and voltages for
different HW states. The PMIC was designed to be used with NXP
i.MX8 SoC and it supports SNVS low power state which seems to
be typical for NXP i.MX SoCs. However, when SNVS is used we must
not allow SW to control enabling/disabling those regulators which
are crucial for system to boot as there is a HW limitation which
causes SW controlled regulators to be kept shut down after SNVS
reset.
Allow setting the SNVS to be used as reset target state and allow
marking those regulators which are critical for boot.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixed regulators do not have associated bus addresses and are typically
placed directly under the root node where their names must still be
unique despite not having a unit address.
Fix the malformed example node which had a unit address but no "reg"
property by dropping the unit address.
Also, try to make the example more useful by using the recommended
generic node name "regulator", but with a suffix reflecting the
regulator name in order to make it unique.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the DT binding document for max77650 regulators.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ROHM bd70528 is a ultra low power PMIC which includes
3 bucks, 3 LDOs and 2 LED drivers. Document the bindings
for them.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the fixed-regulator binding to DT schema format using
json-schema.
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix few trivial language typos in core and drivers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch describes the compatible and the device tree
bindings necessary for the MCP16502 PMIC.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add documentation for regulator modes and suspend states.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform. This driver supports the board
controller chip on the Lochnagar board.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Redefine binding for regulator-coupled-max-spread property in a way that
max-spread values are defined per regulator couple instead of defining
single max-spread for the whole group of coupled regulators.
With that change the following regulators coupling configuration will be
possible:
regA: regulatorA {
regulator-coupled-with = <®B ®C>;
regulator-coupled-max-spread = <100000 300000>;
};
regB: regulatorB {
regulator-coupled-with = <®A ®C>;
regulator-coupled-max-spread = <100000 200000>;
};
regC: regulatorC {
regulator-coupled-with = <®A ®B>;
regulator-coupled-max-spread = <300000 200000>;
};
Note that the regulator-coupled-max-spread property does not have any
users yet, hence it's okay to change the binding.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For state-mem and state-disk regulators can have
various parameters applied such as enabled/disabled,
current mode, voltage etc.
This patch adds documentation on how to set these parameters
in the device tree for the standby state.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Certain hardware may require supply voltage to be changed in steps. Define
new property that allow to describe such hardware.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Redefine binding for regulator-coupled-max-spread property in a way that
max-spread values are defined per regulator couple instead of defining
single max-spread for the whole group of coupled regulators.
With that change the following regulators coupling configuration will be
possible:
regA: regulatorA {
regulator-coupled-with = <®B ®C>;
regulator-coupled-max-spread = <100000 300000>;
};
regB: regulatorB {
regulator-coupled-with = <®A ®C>;
regulator-coupled-max-spread = <100000 200000>;
};
regC: regulatorC {
regulator-coupled-with = <®A ®B>;
regulator-coupled-max-spread = <300000 200000>;
};
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The STPMIC1 regulators supply power to the application processor as well as
to the external system peripherals such as DDR, Flash memories and system
devices.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for the BD71847 which touches both MFD and regulator.
There's a few other bits and pieces included as some dependency patches
had already been applied so would've required rebasing.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluuM/8THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0Az7B/4ye6MIEn8hwKmS36NU3oCvCTFiOZHe
W+T1/O7gOYPSOeHk/4SA8v+A0X2ry+zCschSJtnGDWeZwiZmuhSbQO3SKKM+iAKJ
R1UFioMVd8cr8UySX0ddSdFit+rI+FcZHd8TYAjbseX+0YKZX7z7/rXPVhSEhdU3
BxRy58DJRbLxYofiGruvDd/sj6VFukVmLRjQUE5SqZ8aTKXBbrT7h0Jgi3m7aOmK
g/a+ulMNecq8884oQuBjj1+xCuT02GJsT04BKaXEBsAFX1Fh8IyOxej2N2PaX1z/
6HoPjSAac/Gl9BAgpV0YDdEJJR8yumkdDJubF3SayMyoiv16zMTT1fvC
=t0Ni
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluuNaMTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0H/3B/9u/IGN9LWSnauAivTDqZGx1V3a97e2
ijZSiWaTWFmIBPUNIJgDQirdqsX61Mgu9mTbeD9+tmi2Mm4AOZRJT4pdtzZCehWT
HQuN4dcF9heftf/6Q4c+5yZFAJzOJHHuFklNdDAuM12rUp5IDpKxIo2nrx7MDN6r
RgrxK6eTluvOL4+VJwN/VqXRBWfN857uMjaGkbFV3CrYJh2Ktumts3IcFd18Cpvd
U3gBUYNsPBiQtmGXFkrCCBaYWqn5Ry91CAvpTjoJdZx50xbeXVOEUnUMaidQ4/ru
XL+PqcdTovKuV5OhMzra5MCVt3Cv8Oc/21KeNvFEIV3X6O531LEcksDx
=zN+p
-----END PGP SIGNATURE-----
Merge tag 'bd71847-support' into regulator-4.20
regulator/mfd: Support for the ROHM BD71847
This adds support for the BD71847 which touches both MFD and regulator.
There's a few other bits and pieces included as some dependency patches
had already been applied so would've required rebasing.
Add ROHM BD71847 Power Management IC regulator binding information to
device-tree binding documents.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PMS405 provdies 5 SMPS regulators and 13 LDOs, add these to the RPM
regulator driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the new optional "fsl,pmic-stby-poweroff" property.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Remove an obsolete hack for PPC32 longtrail systems
- Make of_io_request_and_map() "name" arg optional
- Add vendor prefixes for bitmain, Asus, and Y Soft
- Remove 'interrupt-parent' from bindings as it is implicit
- New properties for wm8994 audio codec
- Add 'clocks' property support to SRAM binding
- Add binding for ASPEED coprocessor interrupt controller
- Various binding spelling and link fixes
-----BEGIN PGP SIGNATURE-----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=AV4E
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- Remove an obsolete hack for PPC32 longtrail systems
- Make of_io_request_and_map() "name" arg optional
- Add vendor prefixes for bitmain, Asus, and Y Soft
- Remove 'interrupt-parent' from bindings as it is implicit
- New properties for wm8994 audio codec
- Add 'clocks' property support to SRAM binding
- Add binding for ASPEED coprocessor interrupt controller
- Various binding spelling and link fixes
* tag 'devicetree-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
Documentation: remove dynamic-resolution-notes reference to non-existent file
dt-bindings: Add Y Soft Corporation vendor prefix
of/fdt: Remove PPC32 longtrail hack in memory scan
dt-bindings: remove 'interrupt-parent' from bindings
pinctrl: tegra: fix spelling in devicetree binding document
usb: dwc3: rockchip: Fix PHY documentation links.
dt-bindings: sound: wm8994: document wlf,csnaddr-pd property
dt-bindings: sound: wm8994: document wlf,spkmode-pu property
dt-bindings: sram: Add 'clocks' as an optional property
dt-bindings: Add vendor prefix for AsusTek Computer Inc.
dt-bindings: misc: ASPEED coprocessor interrupt controller
dt-bindings: gpio: pca953x: Document interrupts, update example
drivers/of: Make of_io_request_and_map() "name" argument optional
dt-bindings: Add bitmain vendor prefix
Documentation: devicetree: tilcdc: fix spelling mistake "suppors" -> "supports"
Introduce bindings for RPMh regulator devices found on some
Qualcomm Technlogies, Inc. SoCs. These devices allow a given
processor within the SoC to make PMIC regulator requests which
are aggregated within the RPMh hardware block along with requests
from other processors in the SoC to determine the final PMIC
regulator hardware state.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
'interrupt-parent' is often documented as part of define bindings, but
it is really outside the scope of a device binding. It's never required
in a given node as it is often inherited from a parent node. Or it can
be implicit if a parent node is an 'interrupt-controller' node. So
remove it from all the binding files.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Added support for the CPCAP power management regulator functions on
Tegra based Motorola Xoom devices.
Added sw2_sw4 value tables, which provide power to the Tegra core and
aux devices.
Added the Xoom init tables and device tree compatibility match.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This binding is used to keep the backward compatibility with the current
dtb's [1]. The binding informs the driver that the unused switch regulators
can be disabled.
If it is not specified, the driver doesn't disable the switch regulators.
[1] https://patchwork.kernel.org/patch/10490381/
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add DT bindings for regulators implemented in UniPhier SoCs.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Same general chip description was written in MFD and Regulator
binding documents for ROHM bd71837 PMIC. Remove description from
regulator binding as suggested by Rob H.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Multiple binding documents have various forms of unbalanced quotation
marks. Fix them.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This patch extends binding according to support the pfuze3001 chip.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document devicetree bindings for ROHM BD71837 PMIC regulators.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the DT bindings for the SAW regulators.
The saw-leader is the only property that is configurable in DT.
The saw-slave property allows ganging (grouping) of
several regulators so that their outputs can be combined.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators require keeping their voltage spread below defined
max_spread.
Add properties to provide information on regulators' coupling.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a common device tree property for regulator nodes to support
the specification of allowed operating modes.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
SY8106A is an I2C-controlled adjustable voltage regulator made by
Silergy Corp.
Add its device tree binding.
Signed-off-by: Ondrej Jirman <megous@megous.com>
[Icenowy: Change commit message and slight fixes]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to Devicetree Specification v0.2 document:
"The name of a node should be somewhat generic, reflecting the function
of the device and not its precise programming model."
Do as suggested in the binding example.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the pm8998 and pmi8998 regulators as used in the MSM8998 platform.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The only device-specific node names are "buck1" and "buck2" for the two
regulators present on the device. Sleep mode GPIO and per-regulator GPIO
enable pins are not exposed (the driver does not support them either).
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
These two drivers fail to probe if no name is provided. For details see:
https://www.spinics.net/lists/kernel/msg2457515.html
Signed-off-by: Harald Geyer <harald@ccbib.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Convert to use memblock_virt_alloc in DT code which supports bootmem
arches. With this we can remove the arch specific
early_init_dt_alloc_memory_arch() functions.
- Enable running the DT unittests on UML
- Use SPDX license tags on DT files
- Fix early FDT kconfig ifdef logic
- Clean-up unittest Makefile
- Fix function comment for of_irq_parse_raw
- Add missing documentation for linux,initrd-{start,end} properties
- Clean-up of binding examples using uppercase hex
- Add trivial devices W83773G and Infineon TLV493D-A1B6
- Add missing STM32 SoC bindings
- Various small binding doc fixes
-----BEGIN PGP SIGNATURE-----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=v6gj
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- Convert to use memblock_virt_alloc in DT code which supports
bootmem arches. With this we can remove the arch specific
early_init_dt_alloc_memory_arch() functions.
- Enable running the DT unittests on UML
- Use SPDX license tags on DT files
- Fix early FDT kconfig ifdef logic
- Clean-up unittest Makefile
- Fix function comment for of_irq_parse_raw
- Add missing documentation for linux,initrd-{start,end} properties
- Clean-up of binding examples using uppercase hex
- Add trivial devices W83773G and Infineon TLV493D-A1B6
- Add missing STM32 SoC bindings
- Various small binding doc fixes
* tag 'devicetree-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (23 commits)
xtensa: remove arch specific early DT functions
x86: remove arch specific early_init_dt_alloc_memory_arch
nios2: remove arch specific early_init_dt_alloc_memory_arch
mips: remove arch specific early_init_dt_alloc_memory_arch
metag: remove arch specific early DT functions
cris: remove arch specific early DT functions
libfdt: remove unnecessary include directive from <linux/libfdt.h>
of: unittest: refactor Makefile
of/fdt: use memblock_virt_alloc for early alloc
of: Use SPDX license tag for DT files
of/fdt: Fix #ifdef dependency of early flattree declarations
dt-bindings: h8300 clocksource: correct spelling of pulse
dt-bindings: imx6q-pcie: Add required property for i.MX6SX
mmc: Don't reference Linux-specific OF_GPIO_ACTIVE_LOW flag in DT binding
dt-bindings: Use lower case hex in unit-addresses
dt-bindings: display: panel: Fix compatible string for Toshiba LT089AC29000
dt-bindings: Add Infineon TLV493D-A1B6
dt-bindings: mailbox: ti,message-manager: Fix interrupt name error
dt-bindings: chosen: Document linux,initrd-{start,end}
dt-bindings: arm: document supported STM32 SoC family
...
Some systems need to set regulators to specific states when they enter
low power modes, especially around CPUs. There are many of these modes
depending on the particular runtime state.
Currently the regulator consumers are not granted permission to change
suspend state of regulator devices, the constraints are configured at
startup. In order to allow changes in a vlotage range, we need to add
new properties for voltage range and a flag to give permission to
change the suspend voltage and suspend on/off in suspend mode.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
DT unit addresses should be lower case hex. Fix all the
binding examples.
Converted with the following command from Krzysztof Kozlowski:
sed -e 's/@\([a-fA-F0-9_-]*\) {/@\L\1 {/' -i $(find Documentation/devicetree/bindings -name '*.txt')
Signed-off-by: Rob Herring <robh@kernel.org>
Improve the binding example by removing all the leading 0x to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
Converted using the following command:
find Documentation/devicetree/bindings -name "*.txt" -exec sed -i -e 's/([^ ])\@0x([0-9a-f])/$1\@$2/g' {} +
This is a follow up to commit 48c926cd34
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Rob Herring <robh@kernel.org>
This patch adds support for the Spreadtrum SC2731
voltage regulator device.
Signed-off-by: Erick Chen <erick.chen@spreadtrum.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing memory
leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node. The
prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to dtb
compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage Technology,
shimafuji, Tecon Microprocessor Technologies, DH electronics GmbH,
Opal Kelly, and Next Thing
-----BEGIN PGP SIGNATURE-----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=jgpN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
Improve the binding example by removing all the leading zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find ./Documentation/devicetree/bindings "*.txt"`
Some unnecessary changes were manually fixed.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Document the regulators available on pmi8994 and add support for
this PMIC to the SPMI PMIC regulator driver.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is update for supporting additional devices da9223/4/5.
Only device strings is added because only package type is different.
Signed-off-by: James Ban <James.Ban..opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Improve the binding example by removing the leading 0 from '@08' notation,
which fixes the following build warnings:
Warning (unit_address_format): Node /pfuze100@08 unit name should not have leading 0s
Warning (unit_address_format): Node /pfuze200@08 unit name should not have leading 0s
Warning (unit_address_format): Node /pfuze3000@08 unit name should not have leading 0s
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Convert more DT code to use of_property_read_* API.
- Improve DT overlay support when adding multiple overlays.
- Convert printk's to %pOF format specifiers. Most went via subsystem
trees, but picked up the remaining orphans.
- Correct unittests to use preferred "okay" for "status" property value.
- Add a KASLR seed property.
- Vendor prefixes for Mellanox, Theobroma System, Adaptrum, Moxa.
- Fix modalias buffer handling.
- Clean-up of include paths for building dtbs.
- Add bindings for amc6821, isl1208, tsl2x7x, srf02, and srf10 devices.
- Add nvmem bindings for MediaTek MT7623 and MT7622 SoC.
- Add compatible string for Allwinner H5 Mali-450 GPU.
- Fix links to old OpenFirmware docs with new mirror on devicetree.org.
- Remove status property from binding doc examples.
-----BEGIN PGP SIGNATURE-----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=IBAh
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"There's a few orphans in the conversion to %pOF printf specifiers
included here that no one else picked up.
Summary:
- Convert more DT code to use of_property_read_* API.
- Improve DT overlay support when adding multiple overlays
- Convert printk's to %pOF format specifiers. Most went via subsystem
trees, but picked up the remaining orphans
- Correct unittests to use preferred "okay" for "status" property
value
- Add a KASLR seed property
- Vendor prefixes for Mellanox, Theobroma System, Adaptrum, Moxa
- Fix modalias buffer handling
- Clean-up of include paths for building dtbs
- Add bindings for amc6821, isl1208, tsl2x7x, srf02, and srf10
devices
- Add nvmem bindings for MediaTek MT7623 and MT7622 SoC
- Add compatible string for Allwinner H5 Mali-450 GPU
- Fix links to old OpenFirmware docs with new mirror on
devicetree.org
- Remove status property from binding doc examples"
* tag 'devicetree-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (45 commits)
devicetree: Adjust status "ok" -> "okay" under drivers/of/
dt-bindings: Remove "status" from examples
dt-bindings: pinctrl: sh-pfc: Use generic node name
dt-bindings: Add vendor Mellanox
dt-binding: net/phy: fix interrupts description
virt: Convert to using %pOF instead of full_name
macintosh: Convert to using %pOF instead of full_name
ide: pmac: Convert to using %pOF instead of full_name
microblaze: Convert to using %pOF instead of full_name
dt-bindings: usb: musb: Grammar s/the/to/, s/is/are/
of: Use PLATFORM_DEVID_NONE definition
of/device: Fix of_device_get_modalias() buffer handling
of/device: Prevent buffer overflow in of_device_modalias()
dt-bindings: add amc6821, isl1208 trivial bindings
dt-bindings: add vendor prefix for Theobroma Systems
of: search scripts/dtc/include-prefixes path for both CPP and DTC
of: remove arch/$(SRCARCH)/boot/dts from include search path for CPP
of: remove drivers/of/testcase-data from include search path for CPP
of: return of_get_cpu_node from of_cpu_device_node_get if CPUs are not registered
iio: srf08: add device tree binding for srf02 and srf10
...
Pretty much any node can have a status property, so it doesn't need to
be in examples.
Converted with the following command and removed examples with SoC and
board specific splits:
git grep -l -E 'status.*=.*' Documentation/devicetree/ | xargs sed -i -E '/\sstatus.*=.*"(disabled|ok|okay)/d'
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Document STM32 VREFBUF (voltage reference buffer) which can be used as
voltage reference for ADCs, DACs and external components.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
DT bindings shouldn't reference drivers and they should be OS-agnostic.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DT bindings shouldn't reference drivers and they should be OS-agnostic.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DT bindings shouldn't reference drivers and they should be OS-agnostic.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
add dt-binding document for MediaTek MT6380 PMIC
Signed-off-by: Chenglin Xu <chenglin.xu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "Continuous Voltage" example specifies a pwm-dutycycle-range.
However, an equal sign is missing between the property name and value.
Fix this to allow copy and paste from the documentation when writing an
own .dts file with a pwm-regulator.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators have different settling times for voltage increases and
decreases. Add DT properties to define separate settling times for up-
and downward voltage changes.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We actually can't allow the missing of the regualor name, thus update
the binding doc to make regulator-name property to be required.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The output voltage of a voltage controlled regulator can be controlled
through the voltage of another regulator. The current version of this
driver assumes that the output voltage is a linear function of the control
voltage.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators (some PWM regulators) have the voltage transition
exponentially. On such cases, the settling time for voltage change
is treated as constant time.
Add DT property for providing the settling time for any level of
voltage change for non-linear voltage change.
signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for PF0200 coin cell/super capacitor charger which works as
a current limited voltage source via the LICELL pin. When VIN goes below
a certain threshold LICELL is used to provide power for VSNVS which is
usually used to hold up secure non-volatile storage and the real-time
clock on the SoC.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix typos and add the following to the scripts/spelling.txt:
overide||override
While we are here, fix the doubled "address" in the touched line
Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt.
Also, fix the comment block style in the touched hunks in
drivers/media/dvb-frontends/drx39xyj/drx_driver.h.
Link: http://lkml.kernel.org/r/1481573103-11329-21-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With index usages, device specific properties can be replaced with generic
one. Vpos is index 0 and Vneg is index 1.
DT examples are added as well.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Quite a lot of work going on the core this release, mainly around system
initialization, but a quiet release for drivers:
- Fixes for registration of multiple regulators on a PMIC from Javier
Martinez Canillas and Jon Hunter.
- Cleanups to the regulator_get() code from Dmitry Torokhov
- Lots of constifcation of structs from Bhumika Goyal
- Support for Motorola CPCAP regulators from Tony Lindgren.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlirPJwTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0OJyB/sH4ug2B14/NQjWg/K3M382lUcV24+x
rgq7ucelmHStrqnSU/DTauGL3uoU3Mc9ibGx7nK4SCWaylHpcZjI42dqG+Tkw/CG
/NlF++JOD0lmlXN1kUTqjFyLOGX9Mt5p4Rnbh3xWWJ5Gq30y6IcIJXILrs/9zI4G
OPhAp5Zq7cwT/00PEIxXtI2OcWx9cIeOIwmwE8S0hvNkVQ5oUz5VV+43ZooFVXrN
4l4GzJgEu3huF/zaWq0lW0HHlhWbLcZGNzg8B+6//V3Xrq7dapyQ5vXpARC8DsFm
Q1n2eJlsdbwjTiQy5xOCmk76GnneGt8/6ifhNKidc5LKfoy7DVfPfIF7
=qvYg
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Quite a lot of work going on the core this release, mainly around
system initialization, but a quiet release for drivers:
- fixes for registration of multiple regulators on a PMIC from Javier
Martinez Canillas and Jon Hunter.
- cleanups to the regulator_get() code from Dmitry Torokhov
- lots of constifcation of structs from Bhumika Goyal
- support for Motorola CPCAP regulators from Tony Lindgren"
* tag 'regulator-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (52 commits)
regulator: core: Resolve supplies before disabling unused regulators
regulator: Fix regulator_summary for deviceless consumers
regulator: tps65086: Fix DT node referencing in of_parse_cb
regulator: tps65086: Fix expected switch DT node names
regulator: core: simplify _regulator_get()
regulator: core: have regulator_dev_lookup() return ERR_PTR-encoded errors
regulator: gpio: correct default type
regulator: cpcap: Add basic regulator support
regulator: core: fix typo in regulator_bulk_disable()
regulator: core: optimize devm_regulator_bulk_get()
regulator: core: simplify regulator_bulk_force_disable()
regulator: core: have _regulator_get() accept get_type argument
regulator: core: remove dead code in _regulator_get()
regulator: rn5t618: constify regulator_ops structure
regulator: rc5t583-regulator: constify regulator_ops structure
regulator: pv88090-regulator: constify regulator_ops structure
regulator: pv88080-regulator: constify regulator_ops structure
regulator: pv88060-regulator: constify regulator_ops structure
regulator: pfuze100-regulator: constify regulator_ops structure
regulator: pcf50633-regulator: constify regulator_ops structure
...
The driver defaults to voltage, not current, type so correct
this in the device tree binding documentation.
Signed-off-by: Hans Holmberg <hans@pixelmunchies.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many Motorola phones like droid 4 are using a custom PMIC called CPCAP
or 6556002. This PMIC is used with several SoCs, I've noticed at least
omap3, omap4 and Tegra2 based Motorola phones and tablets using it.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add code to support support for "anatop-enable-bit" device-tree
property. This property translates to LINREG_ENABLE bit in real hardware
and is present on 1p1, 2p5 and 3p0 regulators on i.MX6 and 1p0d regulator
on i.MX7.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the PM8994 regulators found on msm8992,
msm8994 and msm8996 platforms.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[bjorn: Add DT binding doc and vdd_lvs1_2 supply]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This updates the Device Tree according to the preferred way of parsing
the nodes using the regulator framework.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Three files are modified, the driver, header file and the binding document.
Updates for the regulator source file include and .of_match_table entry
and node match checking in the probe() function for a compatible pv88080
silicon type. A new "HVBUCK" is added in source file and added
regsiter definition in header file for pv88080 bb silicion.
The binding documentation changes have been made to reflect these updates.
Signed-off-by: Eric Jeong <eric.jeong.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the Linear Technology LTC3676
8-output I2C voltage regulator IC.
Cc: Jaffer Kapasi <jkapasi@linear.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This set of changes improve some aspects of the atomic API as well as
make use of this new API in the regulator framework to allow properly
dealing with critical regulators controlled by a PWM.
Aside from that there's a bunch of updates and cleanups for existing
drivers, as well as the addition of new drivers for the Broadcom iProc,
STMPE and ChromeOS EC controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=TdEI
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes improve some aspects of the atomic API as well as
make use of this new API in the regulator framework to allow properly
dealing with critical regulators controlled by a PWM.
Aside from that there's a bunch of updates and cleanups for existing
drivers, as well as the addition of new drivers for the Broadcom
iProc, STMPE and ChromeOS EC controllers"
* tag 'pwm/for-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (44 commits)
regulator: pwm: Document pwm-dutycycle-unit and pwm-dutycycle-range
regulator: pwm: Support extra continuous mode cases
pwm: Add ChromeOS EC PWM driver
dt-bindings: pwm: Add binding for ChromeOS EC PWM
mfd: cros_ec: Add EC_PWM function definitions
mfd: cros_ec: Add cros_ec_cmd_xfer_status() helper
pwm: atmel: Use of_device_get_match_data()
pwm: atmel: Fix checkpatch warnings
pwm: atmel: Fix disabling of PWM channels
dt-bindings: pwm: Add R-Car H3 device tree bindings
pwm: rcar: Use ARCH_RENESAS
pwm: tegra: Add support for Tegra186
dt-bindings: pwm: tegra: Add compatible string for Tegra186
pwm: tegra: Avoid overflow when calculating duty cycle
pwm: tegra: Allow 100 % duty cycle
pwm: tegra: Add support for reset control
pwm: tegra: Rename mmio_base to regs
pwm: tegra: Remove useless padding
pwm: tegra: Drop NUM_PWM macro
pwm: lpc32xx: Set PWM_PIN_LEVEL bit to default value
...
Document the pwm-dutycycle-unit and pwm-dutycycle-range properties.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Addition of device tree support for DA9210.
Two files are modified, the driver source file and the binding document.
Updates for the regulator source file include an .of_match_table entry and
node match checking in the probe() function for a compatible da9210 string.
Minor binding documentation changes have been made to the title and the
example.
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a patch for adding description for da9212/da9214.
Signed-off-by: James Ban <James.Ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mvs1 and mvs2 switches are actually called 5vs1 and 5vs2 on
some datasheets. Let's rename them to match the datasheets and
also match the RPM based regulator driver which calls these by
their 5vs names (see qcom_smd-regulator.c). There aren't any
users of these regulators so far, so there aren't any concerns of
DT ABI breakage here. While we're here making updates to the
switches, also mandate usage of the OCP irq for these switches
too.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a404741 ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The S4 supply is sometimes called the boost regulator because it
outputs 5V. Typically it's connected to the 5vs1 and 5vs2
switches for use in USB OTG and HDMI applications. Add support
for this regulator which was mistakenly left out from the initial
submission of this driver.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a404741 ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an optional enable GPIO to the pwm-regulator driver.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Rewrite of the unflattening code to avoid recursion and lessen the
stack usage.
- Rewrite of the phandle args parsing code to get rid of the fixed args
size. This is needed for IOMMU code.
- Sync to latest dtc which adds more dts style checking. These warnings
are enabled with "W=1" compiles.
- Tegra documentation updates related to the above warnings.
- A bunch of spelling and other doc fixes.
- Various vendor prefix additions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXP3OZAAoJEPr7XbWNvGHDEUAQAJLbR9Js7RENPGX/u0NSJNaJ
yQhyNVsz/BkAWFfWT6YEfyNnDY0UcRs2N9RHb+z65TsX1jvJJxLRDLRfz+rExfiZ
cA1RJaF77kPOdA0eZapJIzPvAf97Zik+nzKLsqUPUSYaIzghV5rN6aR2AjXN5AYv
TMQP41NwNQkxfO5I+NOssEB8IBH+DlAzg0LYXw8wNsAJc8o+DgEQjU8cxCqR0NgE
SbpbJNF8tRXEJckZRC+Q7Gyn2J7VglmM/5VTFbBBwgIly2lcLADPVuX/Z6hZE3OH
K7mhNWBu61vI5lU6u7q64ePeb63j+Ut/RR0tTPgjsLg0Qg0ue+6iZ66S9ZHEicbU
wT4A/hjSImvZoQGGMrtUF5HGcaoMHGLGFgFc/Ouox8OQflntQBzuEx/gOQpPXcIT
vdwITNW8/OGV3rgtmRO9mbdSZiAHPsydoTkIl+Ucod3nTrlEEOwgQARYO+2CfSRj
sknndj26Kf+0n0tSv2d4JAEdEozp2ZPyfiAfpPXW74jOmOxeswUb3Kxx8YMwhCEl
+s96rm1vtpNmJzXtuPV3eB0TydWMQ/3NXN6XOS7qEN/5y1AbQqKEoIyJOziBQMxe
c9Eh/YSjsm4uw3Q0wHOI3s4hTwWfuBmwpIsANJVKrRbftPF58bMUBYU/44ReTtA8
iMsrqJpnSCcAyS8doWRY
=s+gW
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Rewrite of the unflattening code to avoid recursion and lessen the
stack usage.
- Rewrite of the phandle args parsing code to get rid of the fixed args
size. This is needed for IOMMU code.
- Sync to latest dtc which adds more dts style checking. These
warnings are enabled with "W=1" compiles.
- Tegra documentation updates related to the above warnings.
- A bunch of spelling and other doc fixes.
- Various vendor prefix additions.
* tag 'devicetree-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (52 commits)
devicetree: Add Creative Technology vendor id
gpio: dt-bindings: add ibm,ppc4xx-gpio binding
of/unittest: Remove unnecessary module.h header inclusion
drivers/of: Fix build warning in populate_node()
drivers/of: Fix depth when unflattening devicetree
of: dynamic: changeset prop-update revert fix
drivers/of: Export of_detach_node()
drivers/of: Return allocated memory from of_fdt_unflatten_tree()
drivers/of: Specify parent node in of_fdt_unflatten_tree()
drivers/of: Rename unflatten_dt_node()
drivers/of: Avoid recursively calling unflatten_dt_node()
drivers/of: Split unflatten_dt_node()
of: include errno.h in of_graph.h
of: document refcount incrementation of of_get_cpu_node()
Documentation: dt: soc: fix spelling mistakes
Documentation: dt: power: fix spelling mistake
Documentation: dt: pinctrl: fix spelling mistake
Documentation: dt: opp: fix spelling mistake
Documentation: dt: net: fix spelling mistakes
Documentation: dt: mtd: fix spelling mistake
...
It is observed that the ramp rate measured on platform is not same as
advertised ramp rate due to platform design variation. On this case,
measured ramp rate is provided with property regulator-ramp-rate.
For such cases, add DT property for device specific configurations.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding support for the tps659038 pmic so it doesn't generate a warning
when running the patch check script to
Documentation/devicetree/bindings/regulator/palmas-pmic.txt
Adding a note that the tps659037 device is a OTP spin of the
tps659038 pmic and device compatible.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
This is the driver for the Powerventure PV88080 BUCKs regulator.
It communicates via an I2C bus to the device.
Signed-off-by: James Ban <James.Ban..opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver MAX8973 supports the driver for Maxim MAX77621.
MAX77621 supports the junction temp warning at 120 degC and
140 degC which is configurable. It generates alert signal when
junction temperature crosses these threshold.
Add DT properties and its binding details to make this
configuration from DT.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_map_mode is needed so to be possible to set initial regulators mode from
the board DTS. Otherwise, for DT boot, regulators are left in their default
state after reset/reboot. Document device specific modes as well.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the regulators available on pm8994 and add support for
this PMIC to the SPMI PMIC regulator driver.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add common DT property for regulator node to support of
active discharge enable/disable configuration of regulator.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 8e6ebfaa9b.
Without the patch reverted regulators will not work. This prevents
MMC to be working for example so the boards can not boot to
MMC rootfs.
Tested it on beaglebone white and bisect also points to the
reverted commit.
The issue can be also fixed by adding "regulator-compatible =" to all board
dts file for the regulators.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Maxim Semiconductor's PMIC MAX77620/MAX20024 has multiple
DCDCs and LDOs.
Add DT binding document to support these regulators via
regulator framework.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the device tree binding documentation for
hi655x PMIC regulator.
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Fei Wang <w.f@huawei.com>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Reviewed-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
LP872x regulators are made active via the EN pin, which might be hooked to a
GPIO. This adds support for driving the GPIO high when the driver is in use.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds documentation for the DT bindings of the regulator
subdevice of ACT8945A MFD.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DT binding doc references the max77802 clocks header file which makes
no sense since of course it doesn't contain data related to the regulators.
It's a copy and paste error, so add a reference to the correct header file.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DT binding doc references the max77802 clocks header file which makes
no sense since of course it doesn't contain data related to the regulators.
It's a copy and paste error, so add a reference to the correct header file.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As usual, the bulk of this release is again DT file contents.
There's a huge number of changes here, and it's challenging to give a crisp
overview of just what is in here. To start with:
New boards:
- TI-based DM3730 from LogicPD (Torpedo)
- Cosmic+ M4 (nommu) initial support (Freescale Vybrid)
- Raspberry Pi 2 DT files
- Watchdog on Meson8b
- Veyron-mickey (ASUS Chromebit) DTS
- Rockchip rk3228 SoC and eval board
- Sigma Designs Tango4
Improvements:
- Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files
- Misc new devices for Rockchip rk3036 and rk3288
- Allwinner updates for misc SoCs and systems
... and a _large_ number of other changes across the field. Devices
added to SoC DTSI and board DTS files for a number of SoC vendors, new
product boards on already-supported SoCs, cleanups and refactorings of
existing DTS/DTSI files and a bunch of other changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XDLa
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, the bulk of this release is again DT file contents.
There's a huge number of changes here, and it's challenging to give a
crisp overview of just what is in here. To start with:
New boards:
- TI-based DM3730 from LogicPD (Torpedo)
- Cosmic+ M4 (nommu) initial support (Freescale Vybrid)
- Raspberry Pi 2 DT files
- Watchdog on Meson8b
- Veyron-mickey (ASUS Chromebit) DTS
- Rockchip rk3228 SoC and eval board
- Sigma Designs Tango4
Improvements:
- Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files
- Misc new devices for Rockchip rk3036 and rk3288
- Allwinner updates for misc SoCs and systems
... and a _large_ number of other changes across the field. Devices
added to SoC DTSI and board DTS files for a number of SoC vendors, new
product boards on already-supported SoCs, cleanups and refactorings of
existing DTS/DTSI files and a bunch of other changes"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (469 commits)
ARM: dts: compulab: add new board description
ARM: versatile: add the syscon LEDs to the DT
dts: vt8500: Fix errors in SDHC node for WM8505
ARM: dts: imx6q: clean up unused ipu2grp
ARM: dts: silk: Add compatible property to "partitions" node
ARM: dts: gose: Add compatible property to "partitions" node
ARM: dts: porter: Add compatible property to "partitions" node
ARM: dts: koelsch: Add compatible property to "partitions" node
ARM: dts: lager: Add compatible property to "partitions" node
ARM: dts: bockw: Add compatible property to "partitions" node
ARM: dts: meson8b: Add watchdog node
Documentation: watchdog: Add new bindings for meson8b
ARM: meson: Add status LED for Odroid-C1
ARM: dts: uniphier: fix a typo in comment block
ARM: bcm2835: Add the auxiliary clocks to the device tree.
ARM: bcm2835: Add devicetree for bcm2836 and Raspberry Pi 2 B
ARM: bcm2835: Move the CPU/peripheral include out of common RPi DT.
ARM: bcm2835: Split the DT for peripherals from the DT for the CPU
ARM: realview: set up cache correctly on the PB11MPCore
ARM: dts: Unify G2D device node with other devices on exynos4
...
Aside from a fix for a spurious warning (which caused more problems than
it fixed in the fixing really) this is all driver updates, including new
drivers for Dialog PV88060/90 and TI LM363x and TPS65086 devices. The
qcom_smd driver has had PM8916 and PMA8084 support added.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWlUWiAAoJECTWi3JdVIfQtywH/0joibyUbL34arXcPNCUUhlo
UnhTgT1kfOoS01ODt9gU49X4/8SRL9HdjcrIV8yTz4Ldb8by8Rd3ZrkO//9zs7BF
5PIqIzEw6FT/Ovsj8Tc35irccMSrwtTIGRrA8zrM/WtWQWcIUWFxMw+j/lewIvvH
jHZNTTLL5XemObSTfvzhbS6PZ8RcvRVXLNJjZYYO5xAEHNg3i5Hxao5p3QKzVJ8m
P5n4jSiTY/pVePcs9dzzQTGjlzkE11KX7DBxnmXOSPZsArSaRIC53DCmqu/JoG+o
3JJBkmRx7IJb0651hclFaUl8Wl56FSst+zigeAj82b301xpVR30iG3xiwYK/AT8=
=NQ6n
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Aside from a fix for a spurious warning (which caused more problems
than it fixed in the fixing really) this is all driver updates,
including new drivers for Dialog PV88060/90 and TI LM363x and TPS65086
devices. The qcom_smd driver has had PM8916 and PMA8084 support
added"
* tag 'regulator-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (36 commits)
regulator: core: remove some dead code
regulator: core: use dev_to_rdev
regulator: lp872x: Get rid of duplicate reference to DVS GPIO
regulator: lp872x: Add missing of_match in regulators descriptions
regulator: axp20x: Fix GPIO LDO enable value for AXP22x
regulator: lp8788: constify regulator_ops structures
regulator: wm8*: constify regulator_ops structures
regulator: da9*: constify regulator_ops structures
regulator: mt6311: Use REGCACHE_RBTREE
regulator: tps65917/palmas: Add bypass ops for LDOs with bypass capability
regulator: qcom-smd: Add support for PMA8084
regulator: qcom-smd: Add PM8916 support
soc: qcom: documentation: Update SMD/RPM Docs
regulator: pv88090: logical vs bitwise AND typo
regulator: pv88090: Fix irq leak
regulator: pv88090: new regulator driver
regulator: wm831x-ldo: Use platform_register/unregister_drivers()
regulator: wm831x-dcdc: Use platform_register/unregister_drivers()
regulator: lp8788-ldo: Use platform_register/unregister_drivers()
regulator: core: Fix nested locking of supplies
...
The mfd/s2mpa01.txt duplicates some of the information about bindings
with old mfd/s2mps11.txt. Now common part exists entirely in
mfd/samsung,sec-core.txt so:
- add company prefix to file name (regulator/samsung,s2mpa01.txt),
- remove duplicated information,
- reorganize the contents to match style of
regulator/samsung,s2mps11.txt.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regulator/s5m8767-regulator.txt duplicates some of the information
about bindings with old mfd/s2mps11.txt. Now common part exists entirely
in mfd/samsung,sec-core.txt so:
- add company prefix to file name (regulator/samsung,s5m8767.txt),
- remove duplicated information,
- reorganize the contents to match style of
regulator/samsung,s2mps11.txt.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Bindings for Samsung S2M and S5M family PMICs are in mess. They are
spread over different files and subdirectories in a non-consistent way.
The devices and respective drivers for them share a lot in common so
everything could be organized in a more readable way.
Reorganize the S2MPS11/13/14/15 Device Tree bindings to match the
drivers for this family of devices:
- move mfd/s2mps11.txt to mfd/samsung,sec-core.txt for the main MFD
driver (common for entire family),
- split clock block to clock/samsung,s2mps11.txt,
- split regulator block to regulator/samsung,s2mps11.txt.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds support and documentation for the PMA8084 regulators
found on APQ8084 platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support and documentation for the PM8916 regulators
found on MSM8916 platforms.
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch moves the qcom,smd-rpm.txt to the correct location and splits
out the smd and rpm documentation. In addition, a smd-rpm-regulator
document is added.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the driver for the Powerventure PV88090 BUCKs and LDOs regulator.
It communicates via an I2C bus to the device.
Signed-off-by: James Ban <James.Ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
remove tps65217.dtsi and adapt all boards, which
used it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This binding describes LM3631 and LM3632 regulator properties.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the driver for the Powerventure PV88060 BUCKs and LDOs regulator.
It communicates via an I2C bus to the device.
Signed-off-by: James Ban <James.Ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Subsystem specific bindings for the Arizona devices are being factored
out of the MFD binding document into separate documents for each
subsystem. This patch adds a binding document that covers the existing
regulator specific bindings.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The anatop regulators are SoC internal LDO regulators usually supplied
by an external PMIC. This patch adds support for specifying the supply
from the device tree using the vin-supply property.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The optional "regulators" is a node and not a property so it should not
be in the "Optional properties" section but in an "Optional nodes" one.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max77802 regulator driver defines the supply name for each regulator
so these can be described in DT but is not mentioned in the binding doc.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a DT property "active-semi,vsel-high" to indicate the VSEL pin
is high. If this property is missing, then assume the VSEL pin is
low(0).
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add device tree based initialization support for tps65023 regulators.
Therefore add macros for regulator definition setting of_match and
regulators_node members. Add initialization of regulator_desc data
using these macros. Remove old regulator_desc initialization.
Add device tree binding document for tps65023 regulators.
Signed-off-by: Thomas Elste <thomas.elste@imms.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce "regulator-allow-set-load" property to make it possible to
flag in the board configuration that a regulator is allowed to have the
load requirements changed.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
- Core Frameworks
- New Base API to traverse devices and their children in reverse order
- Bug Fixes
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
- Fix-ups
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2blS
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support:
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
Core Frameworks:
- New Base API to traverse devices and their children in reverse order
Bug Fixes:
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
Fix-ups:
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures"
* tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: jz4740-adc: Init mask cache in generic IRQ chip
mfd: cros_ec: spi: Add OF match table
mfd: stmpe: Add OF match table
mfd: max77686: Split out regulator part from the DT binding
mfd: Add DT binding for Maxim MAX77802 IC
mfd: max77686: Use a generic name for the PMIC node in the example
mfd: max77686: Don't suggest in binding to use a deprecated property
mfd: Add MFD_CROS_EC dependencies
mfd: cros_ec: Remove CROS_EC_PROTO dependency for SPI and I2C drivers
mfd: axp20x: Add a cell for the usb power_supply part of the axp20x PMICs
mfd: axp20x: Add missing registers, and mark more registers volatile
mfd: arizona: Fixup some formatting/white space errors
mfd: wm8994: Fix NULL pointer exception on missing pdata
of: Add vendor prefix for Nuvoton
mfd: mt6397: Implement wake handler and suspend/resume to handle wake up event
mfd: atmel-hlcdc: Add support for new SoCs
mfd: Export OF module alias information in missing drivers
mfd: stw481x: Export I2C module alias information
mfd: da9062: Support for the DA9063 OnKey in the DA9062 core
mfd: max899x: Avoid redundant irq_data lookup
...
Add separate compatible strings for every platform and populate the
pbias register offset in the driver data.
This helps avoid depending on the dt for pbias register offset.
Also update the dt binding documentation for the new compatible
strings.
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Maxim MAX77686 PMIC is a multi-function device with regulators,
clocks and a RTC. The DT bindings for the clocks are in a separate
file but the bindings for the regulators are inside the mfd part.
To make it consistent with the clocks portion of the binding and
because is more natural to look for regulator bindings under the
bindings/regulator sub-directory, split the regulator portion of
the DT binding and add it as a separate file.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for over current protection (OCP), pin control
selection, soft start strength, and auto-mode.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators can automatically shut down when they detect an
over current event. Add an op (set_over_current_protection) and a
DT property + constraint to support this capability.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a list of supported regulator names to the devicetree
binding documentation for Mediatek MT6311 PMIC.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a patch for supporting da9215 buck converter.
Signed-off-by: James Ban <james.ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add optional interrupt support to the da9210 regulator driver, to handle
over-current, under- and over-voltage, and over-temperature events.
Only the interrupt sources for which we handle events are unmasked, to
avoid interrupts we cannot handle.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
In "[3d7ef30] regulator: pwm-regulator: Simplify voltage to duty-cycle
call" we stopped using max_duty_cycle, so we can retire it from device
data and DT.
There is no need to deprecate this property, as it hasn't hit Mainline
yet.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We're using capitalisation and removing the '-' to mitigate confusion.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
* Add support for continuous-voltage mode
* Put more meat on the bones with regards to voltage-table mode
* Sort out formatting for ease of consumption
Cc: devicetree@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MAX8973/MAX77621 feature an Enhanced Transient Response(ETR)
circuit that is enabled through software. The enhanced transient
response reduces the voltage droop during large load steps by
temporarily allowing all three phases to fire in unison, slewing
total inductor current faster than would normally be possible if
all three phases continued to operate 120deg out of phase. The
enhanced transient response detector features two selectable
sensitivity settings, which select the output voltage slew rate
during load transients that triggers the ETR circuit. The sensitivity
of the ETR detector is set by the CKADV[1:0] bits in the CONTROL2
register.
Add support to configure the ETR through platform data from DT.
Update the DT binding document accordingly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an SPMI regulator driver for Qualcomm's PM8841, PM8941, and
PM8916 PMICs. This driver is based largely on code from
codeaurora.org[1].
[1] https://www.codeaurora.org/cgit/quic/la/kernel/msm-3.10/tree/drivers/regulator/qpnp-regulator.c?h=msm-3.10
Cc: David Collins <collinsd@codeaurora.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators can limit their input current (typically annotated
as ilim). Add an op (set_input_current_limit) and a DT property +
constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators support a "soft start" feature where the voltage
ramps up slowly when the regulator is enabled. Add an op
(set_soft_start) and a DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators need to be configured to pull down a resistor
when the regulator is disabled. Add an op (set_pull_down) and a
DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators have a fixed load that isn't captured by
consumers that the kernel knows about. Add a constraint to
support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Maxim MAX77621 device is high-efficiency, three-phase,
DC-DC step-down switching regulator delivers peak
output currents up to 16A. This device is extension of
MAX8973 and compatible with the register definition.
The MAX77621 has the SHUTDOWN pin which is EN pin on the
MAX8973. On MAX77621, the SHUTDOWN pin (active low) reset
device register to its POR/OTP value. The voltage output
is enabled when SHUTDONW pin is HIGH and EN bit on VOUT
register is HIGH.
For MAX8973, VOUT is enabled when EN bit or EN pin is high.
Add support of the MAX77621 device on max8973 regulator driver
with following changes:
- Make sure SHUTDOWN pin is set HIGH through GPIO calls if
GPIO from AP connected to SHUTDOWN pin provided.
- Enable/disable the rail through register access only.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MAX8973 supports the voltage output enable/disable through its EN
pin. This EN pin can be connected through GPIO from host processor.
Add support to provide GPIO number from platform/DT and if it is
valid GPIO then enable external control default.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are some platform specific parameter required to configure
the device like enable external control, DVS gpio etc.
Add DT parsing of such properties to make platform specific data.
Update DT binding doc accordingly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The act88600/act8846/act8865 regulators have a number of input supplies
supplying the individual regulators. This may even be recursively like on
most Rockchip boards using the act8846 where REG4 is most of the time
connected to the inl1-supply.
Therefore add the ability to specify the input supplies for the individual inputs.
The input-names are taken from the datasheets of act8600, act8846 and act8865.
On the act8600 some regulators do not have separate input supplies.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
