The ROHM BD99954 is a Battery Management LSI for 1-4 cell Lithium-Ion
secondary battery. Intended to be used in space-constraint equipment such
as Low profile Notebook PC, Tablets and other applications. BD99954
provides a Dual-source Battery Charger, two port BC1.2 detection and a
Battery Monitor.
Document the DT bindings for BD99954
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add:
- trickle-charge-current-microamp:
Some chargers have 3 charging stages. First one when battery is almost
empty is often called as trickle-charge. Last state when battery has been
"woken up" is usually called as fast-charge. In addition to this some
chargers have a 'middle state' which ROHM BD99954 data-sheet describes as
pre-charge. Some batteries can benefit from this 3-phase charging
[citation needed].
Introduce trickle-charge-current-microamp so that batteries can give
charging current limit for all three states.
- precharge-upper-limit-microvolt:
When battery voltage has reached certain limit we change from
trickle-charge to next charging state (pre-charge for BD99954). Allow
battery to specify this limit.
- re-charge-voltage-microvolt:
Allow giving a battery specific voltage limit for chargers which can
automatically re-start charging when battery has discharghed down to
this limit.
- over-voltage-threshold-microvolt
Allow specifying voltage threshold after which the battery is assumed to
be faulty.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds the dts binding schema for the cw2015 fuel gauge.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Convert the power_supply.txt to power-supply.yaml.
This conversion entailed fixing up the binding to being yaml and dt
checker compliant.
Added a note in the power_supply.txt to reference the power-supply.yaml
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Setting 'additionalProperties: false' is frequently omitted, but is
important in order to check that there aren't extra undocumented
properties in a binding.
Ideally, we'd just add this automatically and make this the default, but
there's some cases where it doesn't work. For example, if a common
schema is referenced, then properties in the common schema aren't part
of what's considered for 'additionalProperties'. Also, sometimes there
are bus specific properties such as 'spi-max-frequency' that go into
bus child nodes, but aren't defined in the child node's schema.
So let's stick with the json-schema defined default and add
'additionalProperties: false' where needed. This will be a continual
review comment and game of wack-a-mole.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Stephen Boyd <sboyd@kernel.org> # clock
Acked-by: Lee Jones <lee.jones@linaro.org>
Add bq25892, bq25895 and bq25896 to list of supported device IDs in the
bq25890 DT binding document.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Documentation of max17040 based fuel gauge characteristics.
For configure low level state of charge threshold alert signaled from
max17043/max17044 we add "maxim,alert-low-soc-level" property.
Signed-off-by: Matheus Castello <matheus@castello.eng.br>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add a new property to describe the real resistance of coulomb counter chip,
which is used to calibrate the accuracy of the coulomb counter chip.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Since the battery internal resistance can be changed as the temperature
changes, thus add one table to describe the battery resistance percent
in different temperatures to get a accurate battery internal resistance.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The bindings are missing documentation for some of the compatible
strings.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
- DT schemas for PWM, syscon, power domains, SRAM, syscon-reboot,
syscon-poweroff, renesas-irqc, simple-pm-bus, renesas-bsc, pwm-rcar,
Renesas tpu, at24 eeprom, rtc-sh, Allwinner PS/2, sharp,ld-d5116z01b
panel, Arm SMMU, max77650, Meson CEC, Amlogic canvas and DWC3 glue,
Allwinner A10 mUSB and CAN, TI Davinci MDIO, QCom QCS404 interconnect,
Unisoc/Spreadtrum SoCs and UART
- Convert a bunch of Samsung bindings to DT schema
- Convert a bunch of ST stm32 bindings to DT schema
- Realtek and Exynos additions to Arm Mali bindings
- Fix schema errors in RiscV CPU schema
- Various schema fixes from improved meta-schema checks
- Improve the handling of 'dma-ranges' and in particular fix DMA mask
setup on PCI bridges
- Fix a memory leak in add_changeset_property() and DT unit tests.
- Several documentation improvements for schema validation
- Rework build rules to improve schema validation errors
- Color output for dtx_diff
-----BEGIN PGP SIGNATURE-----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=L6uq
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- DT schemas for PWM, syscon, power domains, SRAM, syscon-reboot,
syscon-poweroff, renesas-irqc, simple-pm-bus, renesas-bsc, pwm-rcar,
Renesas tpu, at24 eeprom, rtc-sh, Allwinner PS/2, sharp,ld-d5116z01b
panel, Arm SMMU, max77650, Meson CEC, Amlogic canvas and DWC3 glue,
Allwinner A10 mUSB and CAN, TI Davinci MDIO, QCom QCS404
interconnect, Unisoc/Spreadtrum SoCs and UART
- Convert a bunch of Samsung bindings to DT schema
- Convert a bunch of ST stm32 bindings to DT schema
- Realtek and Exynos additions to Arm Mali bindings
- Fix schema errors in RiscV CPU schema
- Various schema fixes from improved meta-schema checks
- Improve the handling of 'dma-ranges' and in particular fix DMA mask
setup on PCI bridges
- Fix a memory leak in add_changeset_property() and DT unit tests.
- Several documentation improvements for schema validation
- Rework build rules to improve schema validation errors
- Color output for dtx_diff
* tag 'devicetree-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (138 commits)
libfdt: define INT32_MAX and UINT32_MAX in libfdt_env.h
dt-bindings: arm: Remove leftover axentia.txt
of: unittest: fix memory leak in attach_node_and_children
of: overlay: add_changeset_property() memory leak
dt-bindings: interrupt-controller: arm,gic-v3: Add missing type to interrupt-partition-* nodes
dt-bindings: firmware: ixp4xx: Drop redundant minItems/maxItems
dt-bindings: power: Rename back power_domain.txt bindings to fix references
dt-bindings: i2c: stm32: Migrate i2c-stm32 documentation to yaml
dt-bindings: mtd: Convert stm32 fmc2-nand bindings to json-schema
dt-bindings: remoteproc: convert stm32-rproc to json-schema
dt-bindings: mailbox: convert stm32-ipcc to json-schema
dt-bindings: mfd: Convert stm32 low power timers bindings to json-schema
dt-bindings: interrupt-controller: Convert stm32-exti to json-schema
dt-bindings: crypto: Convert stm32 HASH bindings to json-schema
dt-bindings: rng: Convert stm32 RNG bindings to json-schema
dt-bindings: pwm: Convert Samsung PWM bindings to json-schema
dt-bindings: pwm: Convert PWM bindings to json-schema
dt-bindings: serial: Add a new compatible string for SC9863A
dt-bindings: serial: Convert sprd-uart to json-schema
dt-bindings: arm: Add bindings for Unisoc SC9863A
...
Convert the binding document for MAX77650 charger module to YAML.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
There have been some cases of droid4 battery bulging that seem to be
related to being left connected to the charger for several weeks.
It is suspected that the 4.35V charge voltage configured for the battery
is too much in the long run, so lets limit the charge voltage to 4.2V.
It could also be that the batteries are just getting old.
We don't really want to just change the charge voltage to 4.2V as Android
may have charged the battery to 4.35V as pointed out by Pavel Machek.
To add checks for battery voltage, the driver needs to understand the
voltage it's charging at, and also needs to better understand it's
charger state. Right now it only understands connect and disconnect,
while now we need to know also a connected state but not charging.
So let's add better charger state handling with help of chrgcurr2 interrupt
for detecting charge full and retry, and add a check for battery voltage
before we start charging. And then we finally can lower the charge voltage
to 4.2V.
Note that we've been using the same register values as the Android distros
on droid4, so it is suspected that the same problem also exists in Android.
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Rob Herring <robh+dt@kernel.org>
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Core:
* Add over-current health state
* Add standard, adaptive and custom charge types
* Add new properties for start/end charge threshold
New Drivers / Hardware:
* UCS1002 Programmable USB Port Power Controller
* Ingenic JZ47xx Battery Fuel Gauge
* AXP20x USB Power: Add AXP813 support
* AT91 poweroff: Add SAM9X60 support
* OLPC battery: Add XO-1.5 and XO-1.75 support
Misc. Changes:
* syscon-reboot: support mask property
* AXP288 fuel gauge: Blacklist ACEPC T8/T11
- Looks like some vendor thought it's a good idea to
build a desktop system with a fuel gauge, that slowly
"discharges"...
* cpcap-battery: Fix calculation errors
* misc. fixes
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE72YNB0Y/i3JqeVQT2O7X88g7+poFAlzbPpUACgkQ2O7X88g7
+ppU9w/9GDMAHh5LelpuKosuWfdoZMOiMqtyp+GH+Tg4t/cYksTpUFcupKE8sIEU
HG+YHNZdD56rHYz7fF6/SRAWfj1o77+Hr2s7XQlLayReFYuxltPIM+MX+xXpj4Qt
OJcSWnk9233UqfodPAyvC/Tj+I0SgElOUmkhhe5fqNtktQeJgvDO1Gs2oNBZOuMG
+ySTT+8Dba2YbXAHYXYdyzMG1YuDZLbkvSpkYzRBH4CyfDrcTH2zkkfQSu0pAYPk
VwdeWw05yKRNZtWhwS+eUefIXmdu8ZH2BNrYk5PobTeDhhMYx+QzoTuxyhIY+Mbq
I1tabHrIOMy1Xyw0QsbB2/ujrt5SzNv6SLxgKaPvgPSr1uPz3Ogl3+SRziNY3zvN
SmxSedAL5qx/TBTL+rKSKCO66aU8jAdGzvnRfwWcCoQhE+EZF5r0vSn5zIhR2Fxh
fKKph8ZZv7426jPBuXTOurQVRs8daa+DmwHauebq4MNnhftJM1PfTb8SFOwrDTMD
Es4M5BXgn/1RKfqjh0gKTYkbRBCtUhnHUAPmzAKFCbEENc0eC439P3wQ8lP0EzFT
QHpdpPxeMor24HjVldfi0K4hXqNPGEnTlZwq7Asu6NAp0HcgdqIGXiLqQP3/s5ds
gMUqOLNRAywupdpMT7db7JadnVmDRK1sHZnhk4wTAPt4Q6gqcE8=
=qicd
-----END PGP SIGNATURE-----
Merge tag 'for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Core:
- Add over-current health state
- Add standard, adaptive and custom charge types
- Add new properties for start/end charge threshold
New Drivers / Hardware:
- UCS1002 Programmable USB Port Power Controller
- Ingenic JZ47xx Battery Fuel Gauge
- AXP20x USB Power: Add AXP813 support
- AT91 poweroff: Add SAM9X60 support
- OLPC battery: Add XO-1.5 and XO-1.75 support
Misc Changes:
- syscon-reboot: support mask property
- AXP288 fuel gauge: Blacklist ACEPC T8/T11. Looks like some vendor
thought it's a good idea to build a desktop system with a fuel
gauge, that slowly "discharges"...
- cpcap-battery: Fix calculation errors
- misc fixes"
* tag 'for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (54 commits)
power: supply: olpc_battery: force the le/be casts
power: supply: ucs1002: Fix build error without CONFIG_REGULATOR
power: supply: ucs1002: Fix wrong return value checking
power: supply: Add driver for Microchip UCS1002
dt-bindings: power: supply: Add bindings for Microchip UCS1002
power: supply: core: Add POWER_SUPPLY_HEALTH_OVERCURRENT constant
power: supply: core: fix clang -Wunsequenced
power: supply: core: Add missing documentation for CHARGE_CONTROL_* properties
power: supply: core: Add CHARGE_CONTROL_{START_THRESHOLD,END_THRESHOLD} properties
power: supply: core: Add Standard, Adaptive, and Custom charge types
power: supply: axp288_fuel_gauge: Add ACEPC T8 and T11 mini PCs to the blacklist
power: supply: bq27xxx_battery: Notify also about status changes
power: supply: olpc_battery: Have the framework register sysfs files for us
power: supply: olpc_battery: Add OLPC XO 1.75 support
power: supply: olpc_battery: Avoid using platform_info
power: supply: olpc_battery: Use devm_power_supply_register()
power: supply: olpc_battery: Move priv data to a struct
power: supply: olpc_battery: Use DT to get battery version
x86/platform/olpc: Use a correct version when making up a battery node
x86/platform/olpc: Trivial code move in DT fixup
...
Add the DT binding document for the battery charger module of max77650.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This immutable branch contains the changes required for OLPC
1.75 battery, which touches x86 and power-supply and is based
on v5.1-rc1.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
-----BEGIN PGP SIGNATURE-----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=wNRw
-----END PGP SIGNATURE-----
Merge tag 'psy-olpc-1.75-battery-signed' into psy-next
This immutable branch contains the changes required for OLPC
1.75 battery, which touches x86 and power-supply and is based
on v5.1-rc1.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The XO-1 and XO-1.5 batteries apparently differ in an ability to report
ambient temperature.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add documentation for the ingenic-battery driver, used on JZ47xx SoCs.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This adds the "x-powers,axp813-usb-power-supply" to the list of
compatibles for AXP20X VBUS power supply driver.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add documentation for the "charge-status-gpios" property.
Update the "gpios" property with a valid example.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
rename only - no functional changes
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There never was a device called LTC3651, it always was just LT3651.
This circumstance makes it pretty difficult to identify what this
driver is meant to control.channges since
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the example documentation which is missing a semi-colon.
Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add documentation for the "voltage-max-design-microvolt" property.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add one IIO channel named "charge_vol" to read the charge voltage for
the SC27XX fuel gauge controller.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add nvmem properties to calibrate FGU from eFuse controller.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The bq24196 is another variant of the bq24190 charger ic.
Its register set is identical to the bq24192 and it even reuses
the same part number (0x5).
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for the ti,bq24192 variant and a child node for the
usb-otg-vbus regulator.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
changes related to axp813.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
-----BEGIN PGP SIGNATURE-----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=FoKv
-----END PGP SIGNATURE-----
Merge tag 'psy-mfd-axp813-immutable-for-v4.21-signed' into psy-next
Immutable branch between mfd and power-supply for driver
changes related to axp813.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The AXP803/AXP813 AC power supply can limit input current and voltage.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds the binding documentation for Spreadtrum SC27XX series PMICs
fuel gauge unit device, which is used to calculate the battery capacity.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some battery driver will use the open circuit voltage (OCV) value to look
up the corresponding battery capacity percent in one certain degree Celsius.
Thus this patch provides some battery properties to present the OCV table
temperatures and OCV capacity table values.
Suggested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The internal resistance of a battery is not a constant in its life cycle,
this varies over the age of the battery or temperature and so on. But we
just want use one constant battery internal resistance to estimate the
battery capacity. Thus this patch introduces one property to present
the battery factory internal resistance for battery information.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
According to the datasheet, bq27411 is similar to bq27421.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds the binding documentation for Spreadtrum SC2731 charger
device.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The BQ25896 is almost identical to the BQ25890.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
'interrupt-parent' is often documented as part of define bindings, but
it is really outside the scope of a device binding. It's never required
in a given node as it is often inherited from a parent node. Or it can
be implicit if a parent node is an 'interrupt-controller' node. So
remove it from all the binding files.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
This patch adds the devicetree bindings for Maxim's ds2760 battery
monitors.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This compatible property was documented before the driver was renamed to
"SBS" (see commit e57f1b68c4 ("devicetree-bindings: Propagate
bq20z75->sbs rename to dt bindings")). The driver has continued to
support this property as an alternative to "sbs,sbs-battery", and
because we've noticed there are some lingering TI specifics (in the
manufacturer-specific portion of the SBS spec), we'd like to start using
this property again to differentiate.
In typical DT fashion, the <vendor>,<part-number> specifics should be
used ahead of the generic "sbs,sbs-battery" string, so we can handle
vendor specifics -- so document this. Language borrowed mostly from
Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt
Also fixup the example to use this property (it's already implying that
it's "bq20z75@b"); fixup the node name to be generic ("battery", not
"<part-number>"); and fixup some whitespace.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
There were some file movements that changed the location for
some DT bindings. Fix them with:
scripts/documentation-file-ref-check --fix
After manually checking if the new file makes sense.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
This device is software similar to the BQ27426 except it has
different data memory offsets. Add support here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The AXP813 can have a battery as power supply, so let's add it to the
list of compatibles.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This adds basic support for BQ27521 battery monitor, used in Nokia N9
and N950. In particular, battery voltage is important to be able to
tell when the battery is almost empty. Emptying battery on N950 is
pretty painful, as flasher needs to be used to recover phone in such case.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Andrew F. Davis <afd@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This patch adds device tree documentation for the sbs-manager
Signed-off-by: Karl-Heinz Schneider <karl-heinz@schneider-inet.de>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pretty much any node can have a status property, so it doesn't need to
be in examples.
Converted with the following command and removed examples with SoC and
board specific splits:
git grep -l -E 'status.*=.*' Documentation/devicetree/ | xargs sed -i -E '/\sstatus.*=.*"(disabled|ok|okay)/d'
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
LTC2944 is compatible with LTC2943, but uses different
voltage and current computing constants.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
LTC2942 is pin compatible with LTC2941 providing additional
informations about battery voltage and temperature. It can
be runtime detected using bit A7 in the Status register.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Dragos Bogdan <dragos.bogdan@analog.com>
Tested-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The binding for cpcap-battery is missing the standard power-supplies
property as noted by Sebastian Reichel <sebastian.reichel@collabora.co.uk>.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This moves max8903-charger.txt to proper location
for power-supply bindings.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This moves maxim,max14656.txt to proper location for
power-supply bindings.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Documentation of static battery characteristics that can be defined
for batteries that do not embed this data, which are required by
fuel-gauge and charger chips for proper handling of the battery.
The following properties are defined:
voltage-min-design-microvolt
charge-full-design-microamp-hours
energy-full-design-microwatt-hours
precharge-current-microamp
charge-term-current-microamp
constant-charge-current-max-microamp
constant-charge-voltage-max-microamp
Property names are derived from corresponding elements in
enum power_supply_property from include/linux/power_supply.h
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/include/linux/power_supply.h
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add binding for cpcap pmic battery.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This adds the devicetree bindings documentation for the LTC3651 battery charger.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The X-Powers AXP20X and AXP22X PMICs can have a battery as power supply.
This patch adds the DT binding documentation for the battery power
supply which gets various data from the PMIC, such as the battery status
(charging, discharging, full, dead), current max limit, current current,
battery capacity (in percentage), voltage max and min limits, current
voltage and battery capacity (in Ah).
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This add a new device tree binding for LEGO MINDSTORMS EV3 battery. The EV3
has some built-in capability for monitoring the attached battery.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The DT binding document for LTC2941 and LTC2943 battery gauges did not use
a vendor prefix in the listed compatible strings. The driver says that the
manufacturer is Linear Technology which is "lltc" in vendor-prefixes.txt.
There isn't an upstream Device Tree source file that has nodes defined for
these devices, so there's no need to keep the old compatible strings.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The custom CPCAP PMIC used on Motorola phones such as Droid 4 has a
USB battery charger. It can optionally also have a companion chip that
is used for wireless charging.
The charger on CPCAP also can feed VBUS for the USB host mode. This
can be handled by the existing kernel phy_companion interface.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Fix the max8925_batter typo in the file name.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The X-Powers AXP20X and AXP22X PMICs have an AC entry to supply power to
the board. They have a few registers dedicated to the status of the AC
power supply.
This adds the DT binding documentation for the AC power supply for
AXP20X and AXP22X PMICs.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add a binding for the regulator which controls the OTG chargepath switch.
The OTG switch gets its power from pm8941_5vs1, and that should be
expressed as a usb_otg_in-supply property in the DT node for the
charger driver. The regulator name is "otg-vbus".
Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The bq27xxx binding is a standard i2c style binding, however the
deprecated compatible fields and different revisions warrant its own
documentation.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add interrupt specifiers for USB and AC charger input. Interrupt numbers
are from the datasheet.
Fix wrong property for compatible string.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
It is possible to verify AC adapter presence via a register read, without
any physical connection to the ACOK pin on the charger. Allow this.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Adds device tree documentation for SBS charger compilant devices as defined
here: http://sbs-forum.org/specs/sbc110.pdf
Signed-off-by: Nicolas Saenz Julienne <nicolas.saenz@prodys.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This adds the "x-powers,axp223-usb-power-supply" to the list of
compatibles for AXP20X VBUS power supply driver.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
If the ac-detect gpio does not support interrupts, provide a fallback
to poll the gpio at a configurable interval.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The ACOK pin on the bq24735 is active-high, of course meaning that when
AC is OK the pin is high. However, all Tegra dts files have incorrectly
specified active-high even though the signal is inverted on the Tegra
boards. This has worked since the Linux driver has also inverted the
meaning of the GPIO. Fix this situation by simply specifying in the
bindings what everybody else agrees on; that the ti,ac-detect-gpios is
active on AC adapter absence.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Due the driver improvements, update the properties,
- Remove "active-semi,check-battery-temperature" property.
- Add the properties, "active-semi,irq_gpio"
and "active-semi,lbo-gpios".
- As act8945a-charger is regarded as a sub-device, update
the compatible and examples.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Currently the power supply device tree documentation is spread
in .../bindings/power_supply and .../bindings/power. This
unifies the files for chargers and battery fuel gauges in
.../bindings/power/supply and the ones for system reset/shutdown
in .../bindings/power/reset (same structure as used for the
drivers itself).
Signed-off-by: Sebastian Reichel <sre@kernel.org>
