Move the phys, phy-names, reset-gpios properties to the PCIe Root Port node
from Host Bridge node, as agreed upon here [1].
Update the qcom,pcie-common.yaml to include the 'phys' property in the Root
Port node. 'phy-names' property is not needed in Root Port since each Root
Port supports only one PHY. Also, there is already 'reset-gpios' property
defined for PERST# in pci-bus-common.yaml, so use that property instead of
'perst-gpios'.
For backward compatibility, do not remove any existing properties in the
bridge node, but mark them as 'deprecated' instead.
[1] https://lore.kernel.org/linux-pci/20241211192014.GA3302752@bhelgaas/
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
[mani: commit message rewording]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250702-perst-v5-1-920b3d1f6ee1@qti.qualcomm.com
'global' interrupt is used to receive PCIe controller and link specific
events.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250227-pcie-global-irq-v1-9-2b70a7819d1e@linaro.org
Commit 756485bfbb ("dt-bindings: PCI: qcom,pcie-sc7280: Move SC7280 to
dedicated schema") incorrectly removed 'vddpe-3v3-supply' from the
bindings, which results in DT checker warnings like:
arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-dora.dtb: pcie@600000: Unevaluated properties are not allowed ('vddpe-3v3-supply' was unexpected)
from schema $id: http://devicetree.org/schemas/pci/qcom,pcie.yaml#
Note that this property has been part of the Qualcomm PCIe bindings since
2018 and would need to be deprecated rather than simply removed if there is
a desire to replace it with 'vpcie3v3' which is used for some non-Qualcomm
controllers.
Link: https://lore.kernel.org/lkml/Zp_LPixNnh-2Fy5N@hovoldconsulting.com/
Fixes: 756485bfbb ("dt-bindings: PCI: qcom,pcie-sc7280: Move SC7280 to dedicated schema")
Link: https://lore.kernel.org/r/20240723151328.684-1-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Previous commit to this bindings, commit 756485bfbb ("dt-bindings:
PCI: qcom,pcie-sc7280: Move SC7280 to dedicated schema"), updated the
bindings to specify one interrupt only, as the devicetree at that time
did not describe the hardware fully.
The devicetree for SC7280 now specifies eight interrupts, following the
commit b8ba66b40d ("arm64: dts: qcom: sc7280: Add additional MSI
interrupts").
Thus, update the bindings to reflect this.
Link: https://lore.kernel.org/linux-pci/20240722-sc7280-pcie-interrupts-v2-1-a5414d3dbc64@linaro.org
Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Move SC7280 PCIe devices from qcom,pcie.yaml binding to a dedicated file
to make reviewing easier.
This creates equivalent schema file, except:
- Missing required compatible which is actually redundant.
- Expecting exactly one MSI interrupt, instead of eight, because I
could not find interrupt details for this model and current DTS uses
one interrupt.
Link: https://lore.kernel.org/linux-pci/20240205-dt-bindings-pci-qcom-split-continued-v1-2-c333cab5eeea@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
