SPI and I2C bus node names are expected to be "spi" or "i2c",
respectively, with nothing else, a unit-address, or a '-N' index. A
pattern of 'spi0' or 'i2c0' or similar has crept in. Fix all these
cases. Mostly scripted with the following commands:
git grep -l '\si2c[0-9] {' Documentation/devicetree/ | xargs sed -i -e 's/i2c[0-9] {/i2c {/'
git grep -l '\sspi[0-9] {' Documentation/devicetree/ | xargs sed -i -e 's/spi[0-9] {/spi {/'
With this, a few errors in examples were exposed and fixed.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for the microchip,mcp251xfd.yaml
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for power-supply
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230228215433.3944508-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Emails to Krzysztof Opasiak bounce ("Recipient address rejected: User
unknown") so drop his email from maintainers of s3fwrn5 NFC bindings and
driver.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some systems, S3FWRN5 depends on having an external clock enabled
to function correctly. Allow declaring that clock in the device tree.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change interrupt trigger from IRQ_TYPE_LEVEL_HIGH to IRQ_TYPE_EDGE_RISING
for stable NFC I2C interrupt handling.
Samsung's NFC Firmware sends an i2c frame as below.
1. NFC Firmware sets the GPIO(interrupt pin) high when there is an i2c
frame to send.
2. If the CPU's I2C master has received the i2c frame, NFC F/W sets the
GPIO low.
NFC driver's i2c interrupt handler would be called in the abnormal case
as the NFC FW task of number 2 is delayed because of other high priority
tasks.
In that case, NFC driver will try to receive the i2c frame but there isn't
any i2c frame to send in NFC.
It would cause an I2C communication problem. This case would hardly happen.
But, I changed the interrupt as a defense code.
If Driver uses the TRIGGER_RISING instead of the LEVEL trigger,
there would be no problem even if the NFC FW task is delayed.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since S3FWRN82 NFC Chip, The UART interface can be used.
S3FWRN82 supports I2C and UART interface.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The device tree property prefix describes the vendor, which in case of
S3FWRN5 chip is Samsung. Therefore the "s3fwrn5" prefix for "en-gpios"
and "fw-gpios" is not correct and should be deprecated. Introduce
properly named properties for these GPIOs and rename the fw-gpios" to
"wake-gpios" to better describe its purpose.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the Samsung S3FWRN5 NCI NFC controller bindings to dtschema.
This is conversion only so it includes properties with invalid prefixes
(s3fwrn5,en-gpios) which should be addressed later.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
