Add description for bcm63xx gpio-ctrl phandle which allows
access to registers that control phy functionality.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250724035300.20497-3-kylehendrydev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM53134 are B53 switches connected by MDIO.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM6318, BCM6362 and BCM63268 are SoCs with a B53 MMAP switch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DSA switches can fall into one of two categories: switches where all ports
follow standard '(ethernet-)?port' properties, and switches that have
additional properties for the ports.
The scenario where DSA ports are all standardized can be handled by
switches with a reference to the new 'dsa.yaml#/$defs/ethernet-ports'.
The scenario where DSA ports require additional properties can reference
'$dsa.yaml#' directly. This will allow switches to reference these standard
definitions of the DSA switch, but add additional properties under the port
nodes.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Alvin Šipraga <alsi@bang-olufsen.dk> # realtek
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not used by the DSA dt-binding, so remove it from all examples.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Looking at b53_srab_phylink_get_caps() I get no indication of what PHY
modes does port 8 support, since it is implemented circularly based on
the p->mode retrieved from the device tree (and in PHY_INTERFACE_MODE_NA
it reports nothing to supported_interfaces).
However if I look at the b53_switch_chips[] element for BCM58XX_DEVICE_ID,
I see that port 8 is the IMP port, and SRAB means the IMP port is
internal to the SoC. So use phy-mode = "internal" in the example.
Note that this will make b53_srab_phylink_get_caps() go through the
"default" case and report PHY_INTERFACE_MODE_INTERNAL to
supported_interfaces, which is probably a good thing.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
SPI peripheral device bindings need to reference spi-peripheral-props.yaml
in order to use various SPI controller specific properties. Otherwise,
the unevaluatedProperties check will reject any controller specific
properties.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220531220122.2412711-1-robh@kernel.org
Convert the b53 DSA device tree bindings to YAML in order to allow
for automatic checking and such.
Reviewed-by: Rob Herring <robh@kernel.org>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
