Document new partition nodes that declare only the label/name instead
of the reg used to provide an OF node for partition registred at runtime
by parsers. This is required for nvmem system to declare and detect
nvmem-cells.
With these special partitions, the reg / offset is not required and a
'partition-' prefix is needed.
The node name with the 'partition-' prefix stripped, is used to match
the partition allocated by the parser at runtime and the parser will
provide reg and offset of the mtd.
If the partition to match contains invalid char for a node name, the
label binding can be used to declare the partition name.
NVMEM will use the data from the parser and provide the NVMEM cells
declared in the DTS, "connecting" the dynamic partition with a
static declaration of cells in them.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220622010628.30414-2-ansuelsmth@gmail.com
Document new qcom,boot-partition binding used to apply special
read/write layout to boot partitions.
QCOM apply a special layout where spare data is not protected
by ECC for some special pages (used for boot partition). Add
Documentation on how to declare these special pages.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220616001835.24393-4-ansuelsmth@gmail.com
With unevaluatedProperties issues fixed, 'nand-bus-width' and
'nand-ecc-mode' are flagged as undocumented. Removing them from the example
is the easiest solution to silence the warnings.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220525205947.2487165-1-robh@kernel.org
SPI peripheral device bindings need to reference spi-peripheral-props.yaml
in order to use various SPI controller specific properties. Otherwise,
the unevaluatedProperties check will reject any controller specific
properties.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220525205909.2486153-1-robh@kernel.org
Binding schemas which define child node properties such as memory
controllers with timing properties need a separate schema which can be
referenced from child device schemas. This is necessary for
unevaluatedProperties checks to work properly.
Move the ingenic,nemc child properties to its own file and reference
from ingenic,nand.yaml which describes a child NAND controller.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220525210140.2489866-1-robh@kernel.org
Bindings:
- Convert smsc,lan91c111, qcom,spi-qup, qcom,msm-uartdm, qcom,i2c-qup,
qcom,gsbi, i2c-mt65xx, TI wkup_m3_ipc (and new props), qcom,smp2p, TI
timer, Mediatek gnss, Mediatek topckgen, Mediatek apmixedsys, Mediatek
infracfg, fsl,ls-extirq, fsl,layerscape-dcfg, QCom PMIC SPMI,
rda,8810pl-timer, Xilinx zynqmp_ipi, uniphier-pcie, and Ilitek
touchscreen controllers
- Convert various Arm Ltd peripheral IP bindings to schemas
- New bindings for Menlo board CPLD, DH electronics board CPLD,
Qualcomm Geni based QUP I2C, Renesas RZ/G2UL OSTM, Broafcom BCM4751
GNSS, MT6360 PMIC, ASIX USB Ethernet controllers, and Microchip/SMSC
LAN95xx USB Ethernet controllers
- Add vendor prefix for Enclustra
- Add various compatible string additions
- Various example fixes and cleanups
- Remove unused hisilicon,hi6220-reset binding
- Treewide fix properties missing type definition
- Drop some empty and unreferenced .txt bindings
- Documentation improvements for writing schemas
DT driver core:
- Drop static IRQ resources for DT platform devices as IRQ setup is
dynamic and drivers have all been converted to use platform_get_irq()
and friends
- Rework memory allocations and frees for overlays
- Continue overlay notifier callbacks on successful calls and add
unittests
- Handle 'interrupts-extended' in early DT IRQ setup
- Fix of_property_read_string() errors to match documentation
- Ignore disabled nodes in FDT API calls
-----BEGIN PGP SIGNATURE-----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=OUL3
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"Bindings:
- Convert smsc,lan91c111, qcom,spi-qup, qcom,msm-uartdm,
qcom,i2c-qup, qcom,gsbi, i2c-mt65xx, TI wkup_m3_ipc (and new
props), qcom,smp2p, TI timer, Mediatek gnss, Mediatek topckgen,
Mediatek apmixedsys, Mediatek infracfg, fsl,ls-extirq,
fsl,layerscape-dcfg, QCom PMIC SPMI, rda,8810pl-timer, Xilinx
zynqmp_ipi, uniphier-pcie, and Ilitek touchscreen controllers
- Convert various Arm Ltd peripheral IP bindings to schemas
- New bindings for Menlo board CPLD, DH electronics board CPLD,
Qualcomm Geni based QUP I2C, Renesas RZ/G2UL OSTM, Broafcom BCM4751
GNSS, MT6360 PMIC, ASIX USB Ethernet controllers, and
Microchip/SMSC LAN95xx USB Ethernet controllers
- Add vendor prefix for Enclustra
- Add various compatible string additions
- Various example fixes and cleanups
- Remove unused hisilicon,hi6220-reset binding
- Treewide fix properties missing type definition
- Drop some empty and unreferenced .txt bindings
- Documentation improvements for writing schemas
DT driver core:
- Drop static IRQ resources for DT platform devices as IRQ setup is
dynamic and drivers have all been converted to use
platform_get_irq() and friends
- Rework memory allocations and frees for overlays
- Continue overlay notifier callbacks on successful calls and add
unittests
- Handle 'interrupts-extended' in early DT IRQ setup
- Fix of_property_read_string() errors to match documentation
- Ignore disabled nodes in FDT API calls"
* tag 'devicetree-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (86 commits)
of/irq: fix typo in comment
dt-bindings: Fix properties without any type
Revert "dt-bindings: mailbox: qcom-ipcc: add missing properties into example"
dt-bindings: input: touchscreen: ilitek_ts_i2c: Absorb ili2xxx bindings
dt-bindings: timer: samsung,exynos4210-mct: define strict clock order
dt-bindings: timer: samsung,exynos4210-mct: drop unneeded minItems
dt-bindings: timer: cdns,ttc: drop unneeded minItems
dt-bindings: mailbox: zynqmp_ipi: convert to yaml
dt-bindings: usb: ci-hdrc-usb2: fix node node for ethernet controller
dt-bindings: net: add schema for Microchip/SMSC LAN95xx USB Ethernet controllers
dt-bindings: net: add schema for ASIX USB Ethernet controllers
of/fdt: Ignore disabled memory nodes
dt-bindings: arm: fix typos in compatible
dt-bindings: mfd: Add bindings child nodes for the Mediatek MT6360
dt-bindings: display: convert Arm Komeda to DT schema
dt-bindings: display: convert Arm Mali-DP to DT schema
dt-bindings: display: convert Arm HDLCD to DT schema
dt-bindings: display: convert PL110/PL111 to DT schema
dt-bindings: arm: convert vexpress-config to DT schema
dt-bindings: arm: convert vexpress-sysregs to DT schema
...
This is quite a quiet release but some new drivers mean that the
diffstat is fairly large, the new drivers include the aspeed driver
which is migrated from MTD as part of the ongoing move of controllers
with specialised support for SPI flashes into the SPI subsystem.
- Support for devices which flip CPHA during recieve only transfers
(eg, if MOSI and MISO have inverted polarity).
- Overhaul of the i.MX driver, including the addition of PIO support
for better performance on small transfers.
- Migration of the Aspeed driver from MTD.
- Support for Aspeed AST2400, Ingenic JZ4775 and X1/2000 and MediaTek
IPM and SFI.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmKLh9wACgkQJNaLcl1U
h9ApgAf/SvcHRyM06hw+00D2PAco7mxSiAs7rebxj4f0zPRNvUrYbUDWjakeKjoB
ocmpY6AW/vRBUM9xZsiQiLp/9NPltnVghZIBgp5gcS8zaXdxiZjZ68Z+uYp9SP9v
zj8F6bBQzk3lvuY+Cr1f68iXICA62Aa1yX28UFVLZkV0d+0AazpECZkb3hjOiL6P
0qSV6IfoFlJXYsyvAS4/MqYrHklSCD/0Ek09V9jPpZJPHn1ldbFs5zkstfs0PMc/
YeDlpStkjJE4OQ6+z6Ou/wGbcw11nWvKCSqF4bGRXLrgR/uIjOKomwOzaBUf/A6Q
AxQcKMtsBTx0VzYmwJwopj0qDvOq/A==
=6yj3
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This is quite a quiet release but some new drivers mean that the
diffstat is fairly large. The new drivers include the aspeed driver
which is migrated from MTD as part of the ongoing move of controllers
with specialised support for SPI flashes into the SPI subsystem.
- Support for devices which flip CPHA during recieve only transfers
(eg, if MOSI and MISO have inverted polarity).
- Overhaul of the i.MX driver, including the addition of PIO support
for better performance on small transfers.
- Migration of the Aspeed driver from MTD.
- Support for Aspeed AST2400, Ingenic JZ4775 and X1/2000 and MediaTek
IPM and SFI"
* tag 'spi-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (84 commits)
spi: spi-au1550: replace ternary operator with min()
mtd: spi-nor: aspeed: set the decoding size to at least 2MB for AST2600
spi: aspeed: Calibrate read timings
spi: aspeed: Add support for the AST2400 SPI controller
spi: aspeed: Workaround AST2500 limitations
spi: aspeed: Adjust direct mapping to device size
spi: aspeed: Add support for direct mapping
spi: spi-mem: Convert Aspeed SMC driver to spi-mem
spi: Convert the Aspeed SMC controllers device tree binding
spi: spi-cadence: Update ISR status variable type to irqreturn_t
spi: Doc fix - Describe add_lock and dma_map_dev in spi_controller
spi: cadence-quadspi: Handle spi_unregister_master() in remove()
spi: stm32-qspi: Remove SR_BUSY bit check before sending command
spi: stm32-qspi: Always check SR_TCF flags in stm32_qspi_wait_cmd()
spi: stm32-qspi: Fix wait_cmd timeout in APM mode
spi: cadence-quadspi: remove unnecessary (void *) casts
spi: cadence-quadspi: Add missing blank line in cqspi_request_mmap_dma()
spi: spi-imx: mx51_ecspi_prepare_message(): skip writing MX51_ECSPI_CONFIG register if unchanged
spi: spi-imx: add PIO polling support
spi: spi-imx: replace struct spi_imx_data::bitbang by pointer to struct spi_controller
...
* Call of_platform_populate() for MTD partitions
* Check devicetree alias for index
* mtdoops:
- Add a timestamp to the mtdoops header.
- Create a header structure for the saved mtdoops.
- Fix the size of the header read buffer.
* mtdblock: Warn if opened on NAND
* Bindings:
- reserved-memory: Support MTD/block device
- jedec,spi-nor: remove unneeded properties
- Extend fixed-partitions binding
- Add Sercomm (Suzhou) Corporation vendor prefix
MTD driver changes:
* st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
* phram:
- Allow cached mappings
- Allow probing via reserved-memory
* maps: ixp4xx: Drop driver
* bcm47xxpart: Print correct offset on read error
CFI driver changes:
* Rename chip_ready variables
* Add S29GL064N ID definition
* Use chip_ready() for write on S29GL064N
* Move and rename chip_check/chip_ready/chip_good_for_write
NAND core changes:
* Print offset instead of page number for bad blocks
Raw NAND controller drivers:
* Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
* CS553X: simplify the return expression of cs553x_write_ctrl_byte()
* Davinci: Remove redundant unsigned comparison to zero
* Denali: Use managed device resources
* GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
* Intel: Fix possible null-ptr-deref in ebu_nand_probe()
* MPC5121: Check before clk_disable_unprepare() not needed
* Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
* OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
* Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
* Rockchip: Check before clk_disable_unprepare() not needed
* TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
* Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
* Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
* XTX: Add support for XT26G0xA
SPI NOR core changes:
* Read back written SR value to make sure the write was done correctly.
* Introduce a common function for Read ID that manufacturer drivers can
use to verify the Octal DTR switch worked correctly.
* Add helpers for read/write any register commands so manufacturer
drivers don't open code it every time.
* Clarify rdsr dummy cycles documentation.
* Add debugfs entry to expose internal flash parameters and state.
SPI NOR manufacturer drivers changes:
* Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
* Move spi_nor_write_ear() to Winbond module since only Winbond flashes
use it.
* Rework Micron and Cypress Octal DTR enable methods to improve
readability.
* Use the common Read ID function to verify switch to Octal DTR mode for
Micron and Cypress flashes.
* Skip polling status on volatile register writes for Micron and Cypress
flashes since the operation is instant.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmKHhXEACgkQJWrqGEe9
VoQ4FQgAwTWnv7Eps8ngxlOE1WW1Kx+XUFCYN7mUKmDycgRKWWqF0OUu3pU6T3Si
XoOixajzsPC7AJtXbbGKUkH3UtqapCZ/OVxMJzY1S1zKVgS72ChvPth+rNOA5H6f
wkwCRYBCm51hYAlOQeRoFtwLEpOP17KTZw9Jn/u5RVwbQedQnzPj5sb6PddejjF4
9nlk2auJHzENBEEBG3WLRNgvGep8mNNFarzWB4iWrMcG0w1EgBksbIdshoBmu7vj
nKcDJbyA81DqX+8d56BfAFih8H2yCXZmhUzMK+zqnNkd1NuPnDDnrQYFKmKm2hAg
3bIMIzi+8dl/m0TY6BHPHj8oIYpjYA==
=P95J
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD core changes:
- Call of_platform_populate() for MTD partitions
- Check devicetree alias for index
- mtdoops:
- Add a timestamp to the mtdoops header.
- Create a header structure for the saved mtdoops.
- Fix the size of the header read buffer.
- mtdblock: Warn if opened on NAND
- Bindings:
- reserved-memory: Support MTD/block device
- jedec,spi-nor: remove unneeded properties
- Extend fixed-partitions binding
- Add Sercomm (Suzhou) Corporation vendor prefix
MTD driver changes:
- st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
- phram:
- Allow cached mappings
- Allow probing via reserved-memory
- maps: ixp4xx: Drop driver
- bcm47xxpart: Print correct offset on read error
CFI driver changes:
- Rename chip_ready variables
- Add S29GL064N ID definition
- Use chip_ready() for write on S29GL064N
- Move and rename chip_check/chip_ready/chip_good_for_write
NAND core changes:
- Print offset instead of page number for bad blocks
Raw NAND controller drivers:
- Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
- CS553X: simplify the return expression of cs553x_write_ctrl_byte()
- Davinci: Remove redundant unsigned comparison to zero
- Denali: Use managed device resources
- GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
- Intel: Fix possible null-ptr-deref in ebu_nand_probe()
- MPC5121: Check before clk_disable_unprepare() not needed
- Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
- OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
- Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
- Rockchip: Check before clk_disable_unprepare() not needed
- TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
- Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
- Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
- XTX: Add support for XT26G0xA
SPI NOR core changes:
- Read back written SR value to make sure the write was done
correctly.
- Introduce a common function for Read ID that manufacturer drivers
can use to verify the Octal DTR switch worked correctly.
- Add helpers for read/write any register commands so manufacturer
drivers don't open code it every time.
- Clarify rdsr dummy cycles documentation.
- Add debugfs entry to expose internal flash parameters and state.
SPI NOR manufacturer drivers changes:
- Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
- Move spi_nor_write_ear() to Winbond module since only Winbond
flashes use it.
- Rework Micron and Cypress Octal DTR enable methods to improve
readability.
- Use the common Read ID function to verify switch to Octal DTR mode
for Micron and Cypress flashes.
- Skip polling status on volatile register writes for Micron and
Cypress flashes since the operation is instant"
* tag 'mtd/for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (68 commits)
mtd: st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
dt-bindings: mtd: partitions: Extend fixed-partitions binding
dt-bindings: Add Sercomm (Suzhou) Corporation vendor prefix
mtd: phram: Allow cached mappings
mtd: call of_platform_populate() for MTD partitions
mtd: rawnand: renesas: Use runtime PM instead of the raw clock API
dt-bindings: mtd: renesas: Fix the NAND controller description
mtd: rawnand: mpc5121: Check before clk_disable_unprepare() not needed
mtd: rawnand: rockchip: Check before clk_disable_unprepare() not needed
mtd: nand: MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
mtd: rawnand: cs553x: simplify the return expression of cs553x_write_ctrl_byte()
mtd: rawnand: kioxia: Add support for TH58NVG3S0HBAI4
mtd: spi-nor: debugfs: fix format specifier
mtd: spi-nor: support eon en25qh256a variant
mtd: spi-nor: winbond: add support for W25Q512NW-IM
mtd: spi-nor: expose internal parameters via debugfs
mtd: spi-nor: export spi_nor_hwcaps_pp2cmd()
mtd: spi-nor: move spi_nor_write_ear() to winbond module
mtd: spi-nor: amend the rdsr dummy cycles documentation
mtd: cfi_cmdset_0002: Rename chip_ready variables
...
* Print offset instead of page number for bad blocks
Raw NAND controller drivers:
* Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
* CS553X: simplify the return expression of cs553x_write_ctrl_byte()
* Davinci: Remove redundant unsigned comparison to zero
* Denali: Use managed device resources
* GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
* Intel: Fix possible null-ptr-deref in ebu_nand_probe()
* MPC5121: Check before clk_disable_unprepare() not needed
* Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
* OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
* Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
* Rockchip: Check before clk_disable_unprepare() not needed
* TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
* Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
* Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
* XTX: Add support for XT26G0xA
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmKD51AACgkQJWrqGEe9
VoQJ8AgAo8qjO5QQmd76v1q1Regxxl7RsH7hr7r9gJfgTwzhQC/xIyTiorcVPG7B
UDNu4Dwe3OAPbmU54TQNS/AMQkgHGMcIRTVut8+oL+ZnjYl+gv261GxmsfxaK/Hu
Vvvq9X0iyaKpZfyq3uksbsxiXbwMn4fHT7Reaimc9Thw+XKD7AcYWCuFb9GAWfaf
XQUVLg6y4Qk4BR9ZpYAx2v5FH4amJV9RKKTIqiymwcjnBZjYOI29wgKwY1hX+3bm
2Wu4wcccWhDzlV0Casf/hIGBydKx3omV+cJHLtmx7s+dqPvYSUGuvR2nbq5wuMqp
ZcAYeRhGEAYMYcMB/QuKmh4g/Js26w==
=QyqB
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.19' into mtd/next
NAND core:
* Print offset instead of page number for bad blocks
Raw NAND controller drivers:
* Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
* CS553X: simplify the return expression of cs553x_write_ctrl_byte()
* Davinci: Remove redundant unsigned comparison to zero
* Denali: Use managed device resources
* GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
* Intel: Fix possible null-ptr-deref in ebu_nand_probe()
* MPC5121: Check before clk_disable_unprepare() not needed
* Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
* OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
* Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
* Rockchip: Check before clk_disable_unprepare() not needed
* TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
* Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
* Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
* XTX: Add support for XT26G0xA
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add the missing power-domain property which is needed on all the
RZ/N1 SoC IPs.
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20220513104957.257721-2-miquel.raynal@bootlin.com
The "interrupt" property is optional because it is only necessary for
controllers supporting DMAs (Not implemented yet in the new driver).
Cc: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-3-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Another round of removing redundant minItems/maxItems when 'items' list is
specified. This time it is in if/then schemas as the meta-schema was
failing to check this case.
If a property has an 'items' list, then a 'minItems' or 'maxItems' with the
same size as the list is redundant and can be dropped. Note that is DT
schema specific behavior and not standard json-schema behavior. The tooling
will fixup the final schema adding any unspecified minItems/maxItems.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for IIO
Link: https://lore.kernel.org/r/20220503162738.3827041-1-robh@kernel.org
Drop a couple of old, empty .txt binding files which are no longer
referenced.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220422191958.2589318-1-robh@kernel.org
After conversion the jedec,spi-nor DT schema to reference other schemas
(SPI and MTD) and use unevaluatedProperties, few properties are
redundant.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220408063720.12826-1-krzysztof.kozlowski@linaro.org
TI's AM64 SoC has the Error Locator Module. Add compatible and
related properties to support ELM on AM64 SoC.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220326080726.30372-3-rogerq@kernel.org
Convert elm.txt to ti,elm.yaml.
hwmod framework use is deprecated for new platforms
so mark it so.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220326080726.30372-2-rogerq@kernel.org
The node names should be generic and SPI NOR dtschema expects "flash".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220407143405.295907-1-krzysztof.kozlowski@linaro.org
- Add Krzysztof Kozlowski as co-maintainer for DT bindings providing
much needed help.
- DT schema validation now takes DTB files as input rather than
intermediate YAML files. This decouples the validation from the source
level syntax information. There's a bunch of schema fixes as a result
of switching to DTB based validation which exposed some errors
and incomplete schemas and examples.
- Kbuild improvements to explicitly warn users running 'make
dt_binding_check' on missing yamllint
- Expand DT_SCHEMA_FILES kbuild variable to take just a partial filename
or path instead of the full path to 1 file.
- Convert various bindings to schema format: mscc,vsc7514-switch,
multiple GNSS bindings, ahci-platform, i2c-at91, multiple UFS
bindings, cortina,gemini-sata-bridge, cortina,gemini-ethernet, Atmel
SHA, Atmel TDES, Atmel AES, armv7m-systick, Samsung Exynos display
subsystem, nuvoton,npcm7xx-timer, samsung,s3c2410-i2c, zynqmp_dma,
msm/mdp4, rda,8810pl-uart
- New schemas for u-boot environment variable partition, TI clksel
- New compatible strings for Renesas RZ/V2L SoC
- Vendor prefixes for Xen, HPE, deprecated Synopsys, deprecated HiSilicon
- Add/fix schemas for QEMU Arm 'virt' machine
- Drop unused of_alias_get_alias_list() function
- Add a script to check DT unittest EXPECT message output. Pass messages
also now print by default at PR_INFO level to help test automation.
-----BEGIN PGP SIGNATURE-----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=g1li
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Add Krzysztof Kozlowski as co-maintainer for DT bindings providing
much needed help.
- DT schema validation now takes DTB files as input rather than
intermediate YAML files. This decouples the validation from the
source level syntax information. There's a bunch of schema fixes as a
result of switching to DTB based validation which exposed some errors
and incomplete schemas and examples.
- Kbuild improvements to explicitly warn users running 'make
dt_binding_check' on missing yamllint
- Expand DT_SCHEMA_FILES kbuild variable to take just a partial
filename or path instead of the full path to 1 file.
- Convert various bindings to schema format: mscc,vsc7514-switch,
multiple GNSS bindings, ahci-platform, i2c-at91, multiple UFS
bindings, cortina,gemini-sata-bridge, cortina,gemini-ethernet, Atmel
SHA, Atmel TDES, Atmel AES, armv7m-systick, Samsung Exynos display
subsystem, nuvoton,npcm7xx-timer, samsung,s3c2410-i2c, zynqmp_dma,
msm/mdp4, rda,8810pl-uart
- New schemas for u-boot environment variable partition, TI clksel
- New compatible strings for Renesas RZ/V2L SoC
- Vendor prefixes for Xen, HPE, deprecated Synopsys, deprecated
HiSilicon
- Add/fix schemas for QEMU Arm 'virt' machine
- Drop unused of_alias_get_alias_list() function
- Add a script to check DT unittest EXPECT message output. Pass
messages also now print by default at PR_INFO level to help test
automation.
* tag 'devicetree-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (96 commits)
dt-bindings: kbuild: Make DT_SCHEMA_LINT a recursive variable
dt-bindings: nvmem: add U-Boot environment variables binding
dt-bindings: ufs: qcom: Add SM6350 compatible string
dt-bindings: dmaengine: sifive,fu540-c000: include generic schema
dt-bindings: gpio: pca95xx: drop useless consumer example
Revert "of: base: Introduce of_alias_get_alias_list() to check alias IDs"
dt-bindings: virtio,mmio: Allow setting devices 'dma-coherent'
dt-bindings: gnss: Add two more chips
dt-bindings: gnss: Rewrite sirfstar binding in YAML
dt-bindings: gnss: Modify u-blox to use common bindings
dt-bindings: gnss: Rewrite common bindings in YAML
dt-bindings: ata: ahci-platform: Add rk3568-dwc-ahci compatible
dt-bindings: ata: ahci-platform: Add power-domains property
dt-bindings: ata: ahci-platform: Convert DT bindings to yaml
dt-bindings: kbuild: Use DTB files for validation
dt-bindings: kbuild: Pass DT_SCHEMA_FILES to dt-validate
dt-bindings: Add QEMU virt machine compatible
dt-bindings: arm: Convert QEMU fw-cfg to DT schema
dt-bindings: i2c: at91: Add SAMA7G5 compatible strings list
dt-bindings: i2c: convert i2c-at91 to json-schema
...
* Replace the expert mode symbols with a single helper
* Fix misuses of of_match_ptr()
* Remove partid and partname debugfs files
* tests: Fix eraseblock read speed miscalculation for lower partition sizes
* TRX parser: Allow to use on MediaTek MIPS SoCs
MTD driver changes:
* spear_smi: use GFP_KERNEL
* mchp48l640: Add SPI ID table
* mchp23k256: Add SPI ID table
* blkdevs: Avoid soft lockups with some mtd/spi devices
* aspeed-smc: Improve probe resilience
Hyperbus changes:
* HBMC_AM654 should depend on ARCH_K3
NAND core changes:
* ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
* Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
- Make two read-only arrays static const
- Fix compile test issue
Raw NAND core changes:
* Fix misuses of of_match_node()
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
SPI-NAND core changes:
* Delay a little bit the dirmap creation
* Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
* macronix: Use random program load
SPI NOR core changes:
* Move vendor specific code out of the core into vendor drivers.
* Unify all function and object names in the vendor modules.
* Make setup() callback optional to improve readability.
* Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
SPI changes:
* Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
* spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Binding changes:
* Dropped mtd/cortina,gemini-flash.txt
* Convert BCM47xx partitions to json-schema
* Vendor prefixes: Clarify Macronix prefix
* SPI NAND: Convert spi-nand description file to yaml
* Raw NAND chip: Create a NAND chip description
* Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
* Describe Macronix NAND ECC engine
* Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmI7WJcACgkQJWrqGEe9
VoSzpAgAutzRv9TRUiXdBGGlJ851QaZ6ZUvT1bHKTQA+xZi+MZyNmc0cWNg3B70I
PnwyxNAmRkUQKwV5Vgy/sQrt42qZnPmr+8XMq+UiziPmgFdjiTdLqGcN619Hi12t
JqtoKL828R064LSEq5nWsJ2waoGT1nNtZK8kA2qe8ctvmH0YTThriVZUQR4/Befb
OGFheceLFycE/vkktPPr3As4603fMiyDOT7EA3Mtzgjohry0a0TqoakHCaHC/fYo
0/h+x+jJATPtgbWm1ZiV3cZ/Su00+rKuQOsiAWvM/pqDaijsVntBmtK0PRtums2Q
m8LCspuQYNnCINeQXqba9RxACpibDg==
=+6Zk
-----END PGP SIGNATURE-----
Merge tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"There has been a lot of activity in the MTD subsystem recently, with a
number of SPI-NOR cleanups as well as the introduction of ECC engines
that can be used by SPI controllers (hence a few SPI patches in here).
Core MTD changes:
- Replace the expert mode symbols with a single helper
- Fix misuses of of_match_ptr()
- Remove partid and partname debugfs files
- tests: Fix eraseblock read speed miscalculation for lower partition
sizes
- TRX parser: Allow to use on MediaTek MIPS SoCs
MTD driver changes:
- spear_smi: use GFP_KERNEL
- mchp48l640: Add SPI ID table
- mchp23k256: Add SPI ID table
- blkdevs: Avoid soft lockups with some mtd/spi devices
- aspeed-smc: Improve probe resilience
Hyperbus changes:
- HBMC_AM654 should depend on ARCH_K3
NAND core changes:
- ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
- Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
- Make two read-only arrays static const
- Fix compile test issue
Raw NAND core changes:
- Fix misuses of of_match_node()
- Rework of_get_nand_bus_width()
- Remove of_get_nand_on_flash_bbt() wrapper
- Protect access to rawnand devices while in suspend
- bindings: Document the wp-gpios property
Rax NAND controller driver changes:
- atmel: Fix refcount issue in atmel_nand_controller_init
- nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
- rockchip: Fix platform_get_irq.cocci warning
- stm32_fmc2: Add NAND Write Protect support
- pl353: Set the nand chip node as the flash node
- brcmnand: Fix sparse warnings in bcma_nand
- omap_elm: Remove redundant variable 'errors'
- gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
- brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
- Check for error irq
SPI-NAND core changes:
- Delay a little bit the dirmap creation
- Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
- macronix: Use random program load
SPI NOR core changes:
- Move vendor specific code out of the core into vendor drivers.
- Unify all function and object names in the vendor modules.
- Make setup() callback optional to improve readability.
- Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
SPI changes:
- Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
- spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Binding changes:
- Dropped mtd/cortina,gemini-flash.txt
- Convert BCM47xx partitions to json-schema
- Vendor prefixes: Clarify Macronix prefix
- SPI NAND: Convert spi-nand description file to yaml
- Raw NAND chip: Create a NAND chip description
- Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
- Describe Macronix NAND ECC engine
- Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory"
* tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (104 commits)
mtd: nand: ecc: mxic: Fix compile test issue
mtd: nand: mxic-ecc: make two read-only arrays static const
mtd: hyperbus: HBMC_AM654 should depend on ARCH_K3
mtd: core: Remove partid and partname debugfs files
dt-bindings: mtd: partitions: convert BCM47xx to the json-schema
mtd: tests: Fix eraseblock read speed miscalculation for lower partition sizes
mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init
mtd: rawnand: rockchip: fix platform_get_irq.cocci warning
mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set
mtd: spi-nor: renumber flags
mtd: spi-nor: slightly change code style in spi_nor_sr_ready()
mtd: spi-nor: spansion: rename vendor specific functions and defines
mtd: spi-nor: spansion: convert USE_CLSR to a manufacturer flag
mtd: spi-nor: move all spansion specifics into spansion.c
mtd: spi-nor: spansion: slightly rework control flow in late_init()
mtd: spi-nor: micron-st: rename vendor specific functions and defines
mtd: spi-nor: micron-st: convert USE_FSR to a manufacturer flag
mtd: spi-nor: move all micron-st specifics into micron-st.c
mtd: spi-nor: xilinx: correct the debug message
mtd: spi-nor: xilinx: rename vendor specific functions and defines
...
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmI021sACgkQJWrqGEe9
VoTEcggAiFXD+oR0VXTsykiNDiopsAUZwLPGuqk8gvD4ozOYCoAEoYrtnBM6Uybz
W6Hu6Eow/ri1H+uVygUw3RYa4TpxrZrmZnJ1YimXxZjbLYjgE3FS9vzh2l4Bu3yo
fkkQH+nFvk9qVIK8qolAny+LWl37gkSnCd6mPPksYaG5Ds1n1ZgyTZVUz5TOWAjG
QAWUQQfO1iu7+u4CXa9JRTkCf55bT6v6c9Ryq6MA+ok6jVRN6Cj9WhxHtCB5vmOH
Ndmu4V8BqaNKg39ltolqSPuwt3GEh707LRr+YakfnaOM7Sf8E/evn/THSkHwY/yn
bAjpU1gvS13nJ++s8nHwIhHKhoYjTg==
=4Uke
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.18' into mtd/next
Raw NAND core changes:
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Another pass at removing unnecessary use of 'allOf' with a '$ref'.
json-schema versions draft7 and earlier have a weird behavior in that
any keywords combined with a '$ref' are ignored (silently). The correct
form was to put a '$ref' under an 'allOf'. This behavior is now changed
in the 2019-09 json-schema spec and '$ref' can be mixed with other
keywords.
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Marek Behún <kabel@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220228213802.1639658-1-robh@kernel.org
The Xilinx QSPI controller has two advanced modes which allow the
controller to behave differently and consider two flashes as one single
storage.
One of these two modes is quite complex to support from a binding point
of view and is the dual parallel memories. In this mode, each byte of
data is stored in both devices: the even bits in one, the odd bits in
the other. The split is automatically handled by the QSPI controller and
is transparent for the user.
The other mode is simpler to support, it is called dual stacked
memories. The controller shares the same SPI bus but each of the devices
contain half of the data. Once in this mode, the controller does not
follow CS requests but instead internally wires the two CS levels with
the value of the most significant address bit.
Supporting these two modes will involve core changes which include the
possibility of providing two CS for a single SPI device
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220126112608.955728-2-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A few drivers use this property to describe the GPIO pin used to protect
the NAND during program/erase operations.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220217144755.270679-2-christophe.kerello@foss.st.com
Drop mtd/cortina,gemini-flash.txt since it is nearly already handled by
Documentation/devicetree/bindings/mtd/mtd-physmap.yaml.
We add jedec-flash to list of compatible because one board (gemini-dlink-dns-313.dts) needs it.
See commit a10d862e58 ("ARM: dts: Fix the DNS-313 flash compatible")
The flash on the DNS-313 needs to be probed as JEDEC, it does not conform to the common CFI standard.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220211120842.3388592-1-clabbe@baylibre.com
Describe Macronix NAND ECC engine. This engine may be used as an
external engine or can be pipelined with either a raw NAND controller or
a SPI controller. Both hardware designs with a SPI controller are shown
in the examples.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-11-miquel.raynal@bootlin.com
Let's get rid of spi-nand.txt by converting it to yaml schema. While at
converting this file, let's actually pull all the generic properties
from nand-chip.yaml which might apply to a SPI-NAND chip.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-6-miquel.raynal@bootlin.com
Move the NAND chip description out of the NAND controller file. Indeed,
a subsequent part of the properties supported by a raw NAND chip are
also supported by SPI-NAND chips. So let's create a generic NAND chip
description which will be pulled by nand-controller.yaml and later by
spi-nand.yaml as well.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-5-miquel.raynal@bootlin.com
Harmonize the different properties in this file by:
* dropping the non-necessary allOf's
* always defining the keywords in the following order:
- first the "description" (when relevant),
- then the "type"/"$ref" and the other generic keywords ("enum",
"default", etc).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-4-miquel.raynal@bootlin.com
The controller properties should be in the controller 'parent' node,
while properties in the children nodes are specific to the NAND
*chip*. This error was already present during the yaml conversion.
Fixes: 2d472aba15 ("mtd: nand: document the NAND controller/NAND chip DT representation")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-3-miquel.raynal@bootlin.com
The reg property of a NAND device always references the chip-selects.
The ready/busy lines are described in the nand-rb property. I believe
this was a harmless copy/paste error during the conversion to yaml.
Fixes: 212e496935 ("dt-bindings: mtd: Add YAML schemas for the generic NAND options")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-2-miquel.raynal@bootlin.com
This has mostly been a quiet release for the SPI subsystem, almost all
cleanups and fixes to existing drivers. A couple of changes that stand
out:
- Cleanups and support for version specific features in the DesignWare
controller.
- Removal of support for Netlogic devices from the XLP driver, the
platform had previously been removed by MIPS so the support couldn't
be used.
- Conversion of several DT bindings to YAML format.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmHcNHcACgkQJNaLcl1U
h9Bm0Qf7B+2c0Mi8GGJ1TCL44IGTAs9DDOK1uvtaL6VOP5XA1CAm92na4+xghb05
xIxvHF/IyC4rAUjg+8btzgIBSmtBXNELO4JFCVXdKnaFPPjIjJfzE9eMdcK6HVdq
6ZNNVRCFv9E6Dy9cEPyU9dUNKSwJmE6ok8qHxo7f78WeftPWmBvMXa5knE5rj+d4
IiqaJg0L2jdGkTM5Qy0Mm+dI0dTUEkGCrjMhyJXbhry0H7L8z9f9utWI3QE8IXyG
oyt2k7+MSrb6jeb9MRuD/9GC6VdaVv6MWTBEA0yTTsaGZhXwcpy9XJXy7xbbdF6P
g7cd4E4Rlfz4Y9j8GSaDW4AuuUBB3A==
=LgO4
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This has mostly been a quiet release for the SPI subsystem, almost all
cleanups and fixes to existing drivers.
A couple of changes that stand out:
- Cleanups and support for version specific features in the
DesignWare controller.
- Removal of support for Netlogic devices from the XLP driver, the
platform had previously been removed by MIPS so the support
couldn't be used.
- Conversion of several DT bindings to YAML format"
* tag 'spi-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (53 commits)
spi: don't include ptp_clock_kernel.h in spi.h
spi: spi-meson-spifc: Add missing pm_runtime_disable() in meson_spifc_probe
spi: atmel: Fix typo
spi: dt-bindings: mediatek,spi-mtk-nor: Fix example 'interrupts' property
spi: qcom: geni: handle timeout for gpi mode
spi: qcom: geni: set the error code for gpi transfer
spi: spi-mux: Add reference to spi-peripheral-props.yaml schema
spi: ar934x: fix transfer size
spi: pxa2xx: Propagate firmware node
spi: dw: Propagate firmware node
spi: dln2: Propagate firmware node
spi: ar934x: fix transfer and word delays
spi: uniphier: Fix a bug that doesn't point to private data correctly
spi: spi-mtk-nor: add new clock name 'axi' for spi nor
spi: atmel,quadspi: Define sama7g5 QSPI
spi: atmel,quadspi: Convert to json-schema
spi: Fix incorrect cs_setup delay handling
dt-bindings: mtd: spi-nor: Add a reference to spi-peripheral-props.yaml
spi: dt-bindings: cdns,qspi-nor: Move peripheral-specific properties out
spi: dt-bindings: add schema listing peripheral-specific properties
...
Add a Yaml description for this Renesas NAND controller.
As this controller is embedded on different SoC families, provide:
* a family-specific "r-car-gen3" compatible and a more specific
"r8a77951" one
* a family-specific "rzn1" compatible and a more specific "r9a06g032"
one
More compatibles can be added later if new SoCs with this controller
must be supported.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/linux-mtd/20211217142033.353599-2-miquel.raynal@bootlin.com
AM64 SoC contains the GPMC NAND controller. Add compatible for it.
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211209090458.24830-2-rogerq@kernel.org
With 'unevaluatedProperties' support implemented, the TI GPMC example
has a warning:
Documentation/devicetree/bindings/memory-controllers/ti,gpmc.example.dt.yaml: nand@0,0: Unevaluated properties are not allowed ('rb-gpios' was unexpected)
Add the missing definition for 'rb-gpios'.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Roger Quadros <rogerq@kernel.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211206174209.2297565-1-robh@kernel.org
The spi-peripheral-props.yaml schema contains peripheral-specific
properties for SPI controllers that should be present in the peripheral
node. Add a reference to that so its constraints are followed.
additionalProperties: false cannot be used since it marks the controller
properties as unknown. Use unevaluatedProperties: false instead. This
has the side effect of allowing extra properties that are not specified
in the schema. The alternative is to list all the controller properties
in this schema but that would mean every peripheral binding would have
to repeat the same set of properties for each controller.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211109181911.2251-4-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Not all @st.com email address are concerned, only people who have
a specific @foss.st.com email will see their entry updated.
For some people, who left the company, remove their email.
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Cc: Fabien Dessenne <fabien.dessenne@foss.st.com>
Cc: Christophe Roullier <christophe.roullier@foss.st.com>
Cc: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Cc: Lionel Debieve <lionel.debieve@foss.st.com>
Cc: Amelie Delaunay <amelie.delaunay@foss.st.com>
Cc: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Cc: Ludovic Barre <ludovic.barre@foss.st.com>
Cc: Christophe Kerello <christophe.kerello@foss.st.com>
Cc: pascal Paillet <p.paillet@foss.st.com>
Cc: Erwan Le Ray <erwan.leray@foss.st.com>
Cc: Philippe CORNU <philippe.cornu@foss.st.com>
Cc: Yannick Fertre <yannick.fertre@foss.st.com>
Cc: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Cc: Olivier Moysan <olivier.moysan@foss.st.com>
Cc: Hugues Fruchet <hugues.fruchet@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20211110150144.18272-6-patrice.chotard@foss.st.com
Signed-off-by: Rob Herring <robh@kernel.org>
Tidy up a bit the tree, by prefixing all include/dt-bindings/clock/ files
related to Ingenic SoCs with 'ingenic,'.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211016133322.40771-1-paul@crapouillou.net
Convert gpmc-onenand.txt to ti,gpmc-onenand.yaml.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert gpmc-nand.txt to ti,gpmc-nand.yaml.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no GPMC NOR compatible or device driver. GPMC is just
a bus interface over which standard (CFI/JEDC) NOR Flash chips
can be attached.
For NOR chip bindings, please refer to
Documentation/devicetree/bindings/mtd/mtd-physmap.yaml
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* blkdevs:
- Simplify the refcounting in blktrans_{open, release}
- Simplify blktrans_getgeo
- Remove blktrans_ref_mutex
- Simplify blktrans_dev_get
- Use lockdep_assert_held
- Don't hold del_mtd_blktrans_dev in blktrans_{open, release}
* ftl:
- Don't cast away the type when calling add_mtd_blktrans_dev
- Don't cast away the type when calling add_mtd_blktrans_dev
- Use container_of() rather than cast
- Fix use-after-free
- Add discard support
- Allow use of MTD_RAM for testing purposes
* concat:
- Check _read, _write callbacks existence before assignment
- Judge callback existence based on the master
* maps:
- Maps: remove dead MTD map driver for PMC-Sierra MSP boards
* mtdblock:
- Warn if added for a NAND device
- Add comment about UBI block devices
- Update old JFFS2 mention in Kconfig
* partitions:
- Redboot: convert to YAML
NAND core changes:
* Repair Miquel Raynal's email address in MAINTAINERS
* Fix a couple of spelling mistakes in Kconfig
* bbt: Skip bad blocks when searching for the BBT in NAND
* Remove never changed ret variable
Raw NAND changes:
* cafe: Fix a resource leak in the error handling path of 'cafe_nand_probe()'
* intel: Fix error handling in probe
* omap: Fix kernel doc warning on 'calcuate' typo
* gpmc: Fix the ECC bytes vs. OOB bytes equation
SPI-NAND core changes:
* Properly fill the OOB area.
* Fix comment
SPI-NAND drivers changes:
* macronix: Add Quad support for serial NAND flash
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmExS1gACgkQJWrqGEe9
VoSZcAf/SsUDpp/lqc+no4R+eUR/CWrbr3AKu2JjjgCJt0HK++Fy8LQU3FEjn9E8
CNBWYqIVVit1XhqGu192wh0ESsHGlNwjicB3Ul4/RFFC4WKs68kQe0gQrU6z/95V
jaTOW+B7PZh6MFbQROUVI97Cs3OTd8vCE3L2SgIW6krk8tnOEyddlgFsWLISjk6g
Ut1I473653fJAcr5OXEFJLWF+01q2azR9AiAkfKC47IUekTRJqjK2YJpAhsdf4hi
xqazp79sbcNXSHCgOOQv4/f03+SAiufRcNgztwrSWw2fdCg0csBC9ACwmdhhGGfd
7uFn+/Q3sVDOKTN7aAWW1KnykKXsJw==
=JFrk
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD changes:
- blkdevs:
- Simplify the refcounting in blktrans_{open, release}
- Simplify blktrans_getgeo
- Remove blktrans_ref_mutex
- Simplify blktrans_dev_get
- Use lockdep_assert_held
- Don't hold del_mtd_blktrans_dev in blktrans_{open, release}
- ftl:
- Don't cast away the type when calling add_mtd_blktrans_dev
- Don't cast away the type when calling add_mtd_blktrans_dev
- Use container_of() rather than cast
- Fix use-after-free
- Add discard support
- Allow use of MTD_RAM for testing purposes
- concat:
- Check _read, _write callbacks existence before assignment
- Judge callback existence based on the master
- maps:
- Maps: remove dead MTD map driver for PMC-Sierra MSP boards
- mtdblock:
- Warn if added for a NAND device
- Add comment about UBI block devices
- Update old JFFS2 mention in Kconfig
- partitions:
- Redboot: convert to YAML
NAND core changes:
- Repair Miquel Raynal's email address in MAINTAINERS
- Fix a couple of spelling mistakes in Kconfig
- bbt: Skip bad blocks when searching for the BBT in NAND
- Remove never changed ret variable
Raw NAND changes:
- cafe: Fix a resource leak in the error handling path of 'cafe_nand_probe()'
- intel: Fix error handling in probe
- omap: Fix kernel doc warning on 'calcuate' typo
- gpmc: Fix the ECC bytes vs. OOB bytes equation
SPI-NAND core changes:
- Properly fill the OOB area.
- Fix comment
SPI-NAND drivers changes:
- macronix: Add Quad support for serial NAND flash"
* tag 'mtd/for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (30 commits)
mtd: rawnand: cafe: Fix a resource leak in the error handling path of 'cafe_nand_probe()'
mtd_blkdevs: simplify the refcounting in blktrans_{open, release}
mtd_blkdevs: simplify blktrans_getgeo
mtd_blkdevs: remove blktrans_ref_mutex
mtd_blkdevs: simplify blktrans_dev_get
mtd/rfd_ftl: don't cast away the type when calling add_mtd_blktrans_dev
mtd/ftl: don't cast away the type when calling add_mtd_blktrans_dev
mtd_blkdevs: use lockdep_assert_held
mtd_blkdevs: don't hold del_mtd_blktrans_dev in blktrans_{open, release}
mtd: rawnand: intel: Fix error handling in probe
mtd: mtdconcat: Check _read, _write callbacks existence before assignment
mtd: mtdconcat: Judge callback existence based on the master
mtd: maps: remove dead MTD map driver for PMC-Sierra MSP boards
mtd: rfd_ftl: use container_of() rather than cast
mtd: rfd_ftl: fix use-after-free
mtd: rfd_ftl: add discard support
mtd: rfd_ftl: allow use of MTD_RAM for testing purposes
mtdblock: Warn if added for a NAND device
mtd: spinand: macronix: Add Quad support for serial NAND flash
mtdblock: Add comment about UBI block devices
...
* Repair Miquel Raynal's email address in MAINTAINERS
* Fix a couple of spelling mistakes in Kconfig
* bbt: Skip bad blocks when searching for the BBT in NAND
* Remove never changed ret variable
Raw NAND changes:
* cafe: Fix a resource leak in the error handling path of 'cafe_nand_probe()'
* intel: Fix error handling in probe
* omap: Fix kernel doc warning on 'calcuate' typo
* gpmc: Fix the ECC bytes vs. OOB bytes equation
SPI-NAND core changes:
* Properly fill the OOB area.
* Fix comment
SPI-NAND drivers changes:
* macronix: Add Quad support for serial NAND flash
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmExSXUACgkQJWrqGEe9
VoT/9wf7BJ60D3eKfnIPAnZsMgEiaLzlYfaA/z+YCX+O08mHvtApm9RLIievhZ01
+30le9U275AFDGZS5DgmY4Gtbkh5OI5YbgVqFqc4Ev3IJ2pNb7ZdPAjO/Hc5ng8O
9sTPhLr/ZknpmJu6aclCc9+C/lvAZHBQg6nYhstrljRihYJMxNmE+n3/5hveYNCX
fhZIz5uGhMzPwZSJoBMedumJ/kb/VSgznBltc+UubRr/s2ZJ7vAzjG6vptKV7Yrj
/65NyZnKiXOwVdD5TNqnsOKYA3TBN6QPG5Fz/wR/0A2R/c/qQhTTnztU5tLkSTCK
sRiaeUlyxaJcNwer7T+pvgZzyXXAhw==
=iJ+f
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.15' into mtd/next
NAND core changes:
* Repair Miquel Raynal's email address in MAINTAINERS
* Fix a couple of spelling mistakes in Kconfig
* bbt: Skip bad blocks when searching for the BBT in NAND
* Remove never changed ret variable
Raw NAND changes:
* cafe: Fix a resource leak in the error handling path of 'cafe_nand_probe()'
* intel: Fix error handling in probe
* omap: Fix kernel doc warning on 'calcuate' typo
* gpmc: Fix the ECC bytes vs. OOB bytes equation
SPI-NAND core changes:
* Properly fill the OOB area.
* Fix comment
SPI-NAND drivers changes:
* macronix: Add Quad support for serial NAND flash
The 'arm,vexpress-flash' compatible is in use, but has never been documented,
so add it now.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210819182427.1175753-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
"PAGESIZE / 512" is the number of ECC chunks.
"ECC_BYTES" is the number of bytes needed to store a single ECC code.
"2" is the space reserved by the bad block marker.
"2 + (PAGESIZE / 512) * ECC_BYTES" should of course be lower or equal
than the total number of OOB bytes, otherwise it won't fit.
Fix the equation by substituting s/>=/<=/.
Suggested-by: Ryan J. Barnett <ryan.barnett@collins.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20210610143945.3504781-1-miquel.raynal@bootlin.com
Another round of removing redundant minItems/maxItems from new schema in
the recent merge window.
If a property has an 'items' list, then a 'minItems' or 'maxItems' with the
same size as the list is redundant and can be dropped. Note that is DT
schema specific behavior and not standard json-schema behavior. The tooling
will fixup the final schema adding any unspecified minItems/maxItems.
This condition is partially checked with the meta-schema already, but
only if both 'minItems' and 'maxItems' are equal to the 'items' length.
An improved meta-schema is pending.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Will Deacon <will@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-clk@vger.kernel.org
Cc: iommu@lists.linux-foundation.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-rtc@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20210713193453.690290-1-robh@kernel.org
* Convert list_for_each to entry variant
* Use MTD_DEVICE_ATTR_RO/RW() helper macros
* Remove unnecessary OOM messages
* Potential NULL dereference in mtd_otp_size()
* Fix freeing of otp_info buffer
* Create partname and partid debug files for child MTDs
* tests:
- Remove redundant assignment to err
- Fix error return code in mtd_oobtest_init()
* Add OTP NVMEM provider support
* Allow specifying of_node
* Convert sysfs sprintf/snprintf family to sysfs_emit
Bindings changes:
* Convert ti,am654-hbmc.txt to YAML schema
* spi-nor: add otp property
* Add OTP bindings
* add YAML schema for the generic MTD bindings
* Add brcm,trx-magic
MTD device drivers changes:
* Add support for microchip 48l640 EERAM
* Remove superfluous "break"
* sm_ftl:
- Fix alignment of block comment
* nftl:
- Return -ENOMEM when kmalloc failed
* nftlcore:
- Remove set but rewrite variables
* phram:
- Fix error return code in phram_setup()
* plat-ram:
- Remove redundant dev_err call in platram_probe()
MTD parsers changes:
* Qcom:
- Fix leaking of partition name
* Redboot:
- Fix style issues
- Seek fis-index-block in the right node
* trx:
- Allow to use TRX parser on Mediatek SoCs
- Allow to specify brcm, trx-magic in DT
Raw NAND core:
* Allow SDR timings to be nacked
* Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing set.
* Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
* Update dead URL
* Silence static checker warning in nand_setup_interface()
* BBT:
- Fix corner case in bad block table handling
* onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
* Atmel:
- Ensure the data interface is supported.
* Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
* brcmnand:
- Convert bindings to json-schema
* OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
* PL35X:
- New driver
* QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
* Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in marvell_nfc_resume()
* R852:
- Use DEVICE_ATTR_RO() helper macro
* MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
* HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
* Light reorganisation for the introduction of a core resume handler
* Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
* Macronix:
- Add support for serial NAND flash
SPI NOR core changes:
* Ability to dump SFDP tables via sysfs
* Support for erasing OTP regions on Winbond and similar flashes
* Few API doc updates and fixes
* Locking support for MX25L12805D
SPI NOR controller drivers changes:
* Use SPI_MODE_X_MASK in nxp-spifi
* Intel Alder Lake-M SPI serial flash support
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmDcT+IACgkQJWrqGEe9
VoT5Sgf/dt92XA5K2SYNh58KPUwemB9DtkukmniGjo9AqSQwuzHxik3ITHBbFvwP
cSj5PAGoI+zpc+VQz+XuZF1Bsmxaqhy5c0aaJ9TZai2W6keB91in7nJPAhmAI5o2
4zhtAZ9qKp4pOwhFqn6jTd5+l38ok50go3HB4Ibw4UlLuvbUEv11DUcXGKnaAadH
tmXZALf65YAJVruPb4yw+cv7BVVgOPQL8C8ILtsrue7Zgya3JT1205Zbfdjo+X0v
Kl2gh7gGh1YLqzuLLBDUiDnfLIfiu/WTnPqxtqCULR9cLG4oXybXHZe9OsrP8E+P
T68+K8VvT5LKbGh47/OoUfLvrDguCA==
=XVaS
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- Convert list_for_each to entry variant
- Use MTD_DEVICE_ATTR_RO/RW() helper macros
- Remove unnecessary OOM messages
- Potential NULL dereference in mtd_otp_size()
- Fix freeing of otp_info buffer
- Create partname and partid debug files for child MTDs
- tests:
- Remove redundant assignment to err
- Fix error return code in mtd_oobtest_init()
- Add OTP NVMEM provider support
- Allow specifying of_node
- Convert sysfs sprintf/snprintf family to sysfs_emit
Bindings changes:
- Convert ti,am654-hbmc.txt to YAML schema
- spi-nor: add otp property
- Add OTP bindings
- add YAML schema for the generic MTD bindings
- Add brcm,trx-magic
MTD device drivers changes:
- Add support for microchip 48l640 EERAM
- Remove superfluous "break"
- sm_ftl:
- Fix alignment of block comment
- nftl:
- Return -ENOMEM when kmalloc failed
- nftlcore:
- Remove set but rewrite variables
- phram:
- Fix error return code in phram_setup()
- plat-ram:
- Remove redundant dev_err call in platram_probe()
MTD parsers changes:
- Qcom:
- Fix leaking of partition name
- Redboot:
- Fix style issues
- Seek fis-index-block in the right node
- trx:
- Allow to use TRX parser on Mediatek SoCs
- Allow to specify brcm, trx-magic in DT
Raw NAND core:
- Allow SDR timings to be nacked
- Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing
set.
- Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
- Update dead URL
- Silence static checker warning in nand_setup_interface()
- BBT:
- Fix corner case in bad block table handling
- onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
- Atmel:
- Ensure the data interface is supported.
- Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
- brcmnand:
- Convert bindings to json-schema
- OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
- PL35X:
- New driver
- QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
- Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in
marvell_nfc_resume()
- R852:
- Use DEVICE_ATTR_RO() helper macro
- MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
- HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
- Light reorganisation for the introduction of a core resume handler
- Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
- Macronix:
- Add support for serial NAND flash
SPI NOR core changes:
- Ability to dump SFDP tables via sysfs
- Support for erasing OTP regions on Winbond and similar flashes
- Few API doc updates and fixes
- Locking support for MX25L12805D
SPI NOR controller drivers changes:
- Use SPI_MODE_X_MASK in nxp-spifi
- Intel Alder Lake-M SPI serial flash support"
* tag 'mtd/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (125 commits)
mtd: spi-nor: remove redundant continue statement
mtd: rawnand: omap: Add larger page NAND chips support
mtd: rawnand: omap: Various style fixes
mtd: rawnand: omap: Check return values
mtd: rawnand: omap: Rename a macro
mtd: rawnand: omap: Aggregate the HW configuration of the ELM
mtd: rawnand: pl353: Add support for the ARM PL353 SMC NAND controller
dt-bindings: mtd: pl353-nand: Describe this hardware controller
MAINTAINERS: Add PL353 NAND controller entry
mtd: rawnand: qcom: avoid writing to obsolete register
mtd: rawnand: marvell: Minor documentation correction
mtd: rawnand: r852: use DEVICE_ATTR_RO() helper macro
mtd: spinand: add SPI-NAND MTD resume handler
mtd: spinand: Add spinand_init_flash() helper
mtd: spinand: add spinand_read_cfg() helper
mtd: rawnand: marvell: add missing clk_disable_unprepare() on error in marvell_nfc_resume()
mtd: rawnand: arasan: Finer grain NV-DDR configuration
mtd: rawnand: arasan: Rename the data interface register
mtd: rawnand: onfi: Fix endianness when reading NV-DDR values
mtd: rawnand: arasan: Use the right DMA mask
...
* Allow SDR timings to be nacked
* Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing set.
* Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
* Update dead URL
* Silence static checker warning in nand_setup_interface()
* BBT:
- Fix corner case in bad block table handling
* onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
* Atmel:
- Ensure the data interface is supported.
* Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
* brcmnand:
- Convert bindings to json-schema
* OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
* PL35X:
- New driver
* QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
* Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in marvell_nfc_resume()
* R852:
- Use DEVICE_ATTR_RO() helper macro
* MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
* HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
* Light reorganisation for the introduction of a core resume handler
* Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
* Macronix:
- Add support for serial NAND flash
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmDS290ACgkQJWrqGEe9
VoS77wgAgKnqfFwbqzdSecVmXai9roSNHi/aMpVJvvLHSTCV35iCcNNtrz0Jno56
t/8twVPPZUI6f3vPXk5+NjKRCb8Oif3oU+tNxqG6mwzrBRf5R80pYCMm+HGPWZaK
+MolqGAbgFO088DTK5fGNtmbnb5fPT174RKRBGEH5NgK5M1q95uF8fIjBXDcjVe2
hvAyoqqC7i/bp40sxRtglgBpYYz+KUjCX11JvJPa5IuVU+8ezZSKJLSo5/CtgIKJ
mRQ8p8myiUjZngcnebjTrAA5AwQ13ai9ofKG0pHkdxwOq4lSRNgKou0Hk5+oq+s0
BFEuXnUrdnJNU7+XV+kAqBoT6WOFzg==
=I/9X
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
Raw NAND core:
* Allow SDR timings to be nacked
* Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing set.
* Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
* Update dead URL
* Silence static checker warning in nand_setup_interface()
* BBT:
- Fix corner case in bad block table handling
* onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
* Atmel:
- Ensure the data interface is supported.
* Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
* brcmnand:
- Convert bindings to json-schema
* OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
* PL35X:
- New driver
* QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
* Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in marvell_nfc_resume()
* R852:
- Use DEVICE_ATTR_RO() helper macro
* MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
* HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
* Light reorganisation for the introduction of a core resume handler
* Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
* Macronix:
- Add support for serial NAND flash
Convert ti,am654-hbmc.txt to YAML schema for better checks and
validations of DT.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Convert the mtd-physmap binding to DT schema format. The arm-versatile,
cypress,hyperflash and intel,ixp4xx-flash are all just an additional
compatible string, so they are all merged into the main schema.
There doesn't appear to be any users nor support for 'vendor-id' and
'device-id', so these have been dropped.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210607193500.3085920-1-robh@kernel.org
Convert the mux controller bindings to DT schema.
Cc: Peter Rosin <peda@axentia.se>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210526184839.2937899-4-robh@kernel.org
To reach higher capacities, arrays of chips are now pretty common.
Unfortunately, most of the controllers have been designed a decade ago
and did not all anticipate the need for several chip-selects. The new
cs-gpios property allows to workaround this limitation by adding as many
GPIO chip-select as needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20210510171800.27225-1-miquel.raynal@bootlin.com
SPI-NOR flashes may have OTP regions and have a nvmem binding. This
binding is described in mtd.yaml.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210424110608.15748-5-michael@walle.cc
Flash devices can have one-time-programmable regions. Add a nvmem
binding so they can be used as a nvmem provider.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210424110608.15748-4-michael@walle.cc
This adds the description of an additional property which allows to
specify a custom partition parser magic to detect a trx partition.
Buffalo has multiple device which are using the trx format, but with
different magic values.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210418214616.239574-2-hauke@hauke-m.de
This helps validating DTS files.
Changes that require mentioning:
1. Property "clock" was renamed to "clocks"
2. Duplicated properties (defined in nand-controller.yaml) were dropped
3. Compatible "brcm,nand-bcm63168" was added
4. SoC specific "compatible" cases got limited controller versions
Examples changes:
1. Nodes "nand" were renamed to "nand-controller"
2. Nodes "nandcs" were renamed to "nand"
3. Dropped partitions as they were using old syntax and are well
documented elsewhere anyway
This rewritten binding validates cleanly using the "dt_binding_check".
Some Linux stored DTS files will require updating to make "dtbs_check"
happy.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210423050536.29504-1-zajec5@gmail.com
The Sigma Designs Tango support has been removed, but 2 binding docs
for NAND and PCIe were missed. Remove them.
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-pci@vger.kernel.org
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210430153225.3366000-1-robh@kernel.org/
Signed-off-by: Rob Herring <robh@kernel.org>
* Handle possible -EPROBE_DEFER from parse_mtd_partitions()
NAND core:
* Fix error handling in nand_prog_page_op() (x2)
* Add a helper to retrieve the number of ECC bytes per step
* Add a helper to retrieve the number of ECC steps
* Let ECC engines advertize the exact number of steps
* ECC Hamming:
- Populate the public nsteps field
- Use the public nsteps field
* ECC BCH:
- Populate the public nsteps field
- Use the public nsteps field
Raw NAND core:
* Add support for secure regions in NAND memory
* Try not to use the ECC private structures
* Remove duplicate include in rawnand.h
* BBT:
- Skip bad blocks when searching for the BBT in NAND
Raw NAND controller drivers:
* Qcom:
- Convert bindings to YAML
- Use dma_mapping_error() for error check
- Add missing nand_cleanup() in error path
- Return actual error code instead of -ENODEV
- Update last code word register
- Add helper to configure location register
- Rename parameter name in macro
- Add helper to check last code word
- Convert nandc to chip in Read/Write helper
- Update register macro name for 0x2c offset
* GPMI:
- Fix a double free in gpmi_nand_init
* Rockchip:
- Use flexible-array member instead of zero-length array
* Atmel:
- Update ecc_stats.corrected counter
* MXC:
- Remove unneeded of_match_ptr()
* R852:
- replace spin_lock_irqsave by spin_lock in hard IRQ
* Brcmnand:
- Move to polling in pio mode on oops write
- Read/write oob during EDU transfer
- Fix OOB R/W with Hamming ECC
* FSMC:
- Fix error code in fsmc_nand_probe()
* OMAP:
- Use ECC information from the generic structures
SPI-NAND core:
* Add missing MODULE_DEVICE_TABLE()
SPI-NAND drivers:
* gigadevice: Support GD5F1GQ5UExxG
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmB1XbkACgkQJWrqGEe9
VoSWEAf6Al9DFds3w32oS8OB19pMb66jWLPvt//gIwV4tzSIsauQLqo4uBqDUPSt
EdUyehN6W792qsekmOReRc4ZcS2HpNPT5PRwYtsxPMkVmEL56tqs5ObNPGNOwvoH
9vyvsx7EhSu10a9JHjgJeNMVOBDMA8quXqHw0Y3cL2UBpuCYMm37ANF8okdvOmmr
Ykg1nCbfZL/dxFCGZ15ZuYuGQXea8PUryyxXUsWLDvsHg4KuhQKKtkarXmzz6XiD
tAyShtSrJFo/T0FniWc8jFbaq8WkU7XBg5f5qTTt5uT4JoXWGmjbIbXG0My91RKY
RO0b6z/odPOW1UHarlK8HrKW22YF9A==
=+fKJ
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
MTD core:
* Handle possible -EPROBE_DEFER from parse_mtd_partitions()
NAND core:
* Fix error handling in nand_prog_page_op() (x2)
* Add a helper to retrieve the number of ECC bytes per step
* Add a helper to retrieve the number of ECC steps
* Let ECC engines advertize the exact number of steps
* ECC Hamming:
- Populate the public nsteps field
- Use the public nsteps field
* ECC BCH:
- Populate the public nsteps field
- Use the public nsteps field
Raw NAND core:
* Add support for secure regions in NAND memory
* Try not to use the ECC private structures
* Remove duplicate include in rawnand.h
* BBT:
- Skip bad blocks when searching for the BBT in NAND
Raw NAND controller drivers:
* Qcom:
- Convert bindings to YAML
- Use dma_mapping_error() for error check
- Add missing nand_cleanup() in error path
- Return actual error code instead of -ENODEV
- Update last code word register
- Add helper to configure location register
- Rename parameter name in macro
- Add helper to check last code word
- Convert nandc to chip in Read/Write helper
- Update register macro name for 0x2c offset
* GPMI:
- Fix a double free in gpmi_nand_init
* Rockchip:
- Use flexible-array member instead of zero-length array
* Atmel:
- Update ecc_stats.corrected counter
* MXC:
- Remove unneeded of_match_ptr()
* R852:
- replace spin_lock_irqsave by spin_lock in hard IRQ
* Brcmnand:
- Move to polling in pio mode on oops write
- Read/write oob during EDU transfer
- Fix OOB R/W with Hamming ECC
* FSMC:
- Fix error code in fsmc_nand_probe()
* OMAP:
- Use ECC information from the generic structures
SPI-NAND core:
* Add missing MODULE_DEVICE_TABLE()
SPI-NAND drivers:
* gigadevice: Support GD5F1GQ5UExxG
On a typical end product, a vendor may choose to secure some regions in
the NAND memory which are supposed to stay intact between FW upgrades.
The access to those regions will be blocked by a secure element like
Trustzone. So the normal world software like Linux kernel should not
touch these regions (including reading).
So let's add a property for declaring such secure regions so that the
drivers can skip touching them.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210402150128.29128-3-manivannan.sadhasivam@linaro.org
Document nvmem-cells compatible used to treat mtd partitions as a
nvmem provider.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210312062830.20548-3-ansuelsmth@gmail.com
- Sync dtc to upstream version v1.6.0-51-g183df9e9c2b9 and build
host fdtoverlay
- Add kbuild support to build DT overlays (%.dtbo)
- Drop NULLifying match table in of_match_device(). In preparation for
this, there are several driver cleanups to use
(of_)?device_get_match_data().
- Drop pointless wrappers from DT struct device API
- Convert USB binding schemas to use graph schema and remove old plain
text graph binding doc
- Convert spi-nor and v3d GPU bindings to DT schema
- Tree wide schema fixes for if/then schemas, array size constraints,
and undocumented compatible strings in examples
- Handle 'no-map' correctly for already reserved memblock regions
-----BEGIN PGP SIGNATURE-----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=9V4A
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Sync dtc to upstream version v1.6.0-51-g183df9e9c2b9 and build host
fdtoverlay
- Add kbuild support to build DT overlays (%.dtbo)
- Drop NULLifying match table in of_match_device().
In preparation for this, there are several driver cleanups to use
(of_)?device_get_match_data().
- Drop pointless wrappers from DT struct device API
- Convert USB binding schemas to use graph schema and remove old plain
text graph binding doc
- Convert spi-nor and v3d GPU bindings to DT schema
- Tree wide schema fixes for if/then schemas, array size constraints,
and undocumented compatible strings in examples
- Handle 'no-map' correctly for already reserved memblock regions
* tag 'devicetree-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
driver core: platform: Drop of_device_node_put() wrapper
of: Remove of_dev_{get,put}()
dt-bindings: usb: Change descibe to describe in usbmisc-imx.txt
dt-bindings: can: rcar_canfd: Group tuples in pin control properties
dt-bindings: power: renesas,apmu: Group tuples in cpus properties
dt-bindings: mtd: spi-nor: Convert to DT schema format
dt-bindings: Use portable sort for version cmp
dt-bindings: ethernet-controller: fix fixed-link specification
dt-bindings: irqchip: Add node name to PRUSS INTC
dt-bindings: interconnect: Fix the expected number of cells
dt-bindings: Fix errors in 'if' schemas
dt-bindings: iommu: renesas,ipmmu-vmsa: Make 'power-domains' conditionally required
dt-bindings: Fix undocumented compatible strings in examples
kbuild: Add support to build overlays (%.dtbo)
scripts: dtc: Remove the unused fdtdump.c file
scripts: dtc: Build fdtoverlay tool
scripts/dtc: Update to upstream version v1.6.0-51-g183df9e9c2b9
scripts: dtc: Fetch fdtoverlay.c from external DTC project
dt-bindings: thermal: sun8i: Fix misplaced schema keyword in compatible strings
dt-bindings: iio: dac: Fix AD5686 references
...
The main focus of this release from a framework point of view has been
spi-mem where we've acquired support for a few new hardware features
which enable better performance on suitable hardware. Otherwise mostly
thanks to Arnd's cleanup efforts on old platforms we've removed several
obsolete drivers which just about balance out the newer drivers we've
added this cycle.
- Allow drivers to flag if they are unidirectional.
- Support for DTR mode and hardware acceleration of dummy cycles in spi-mem.
- Support for Allwinder H616, Intel Lightning Mountain, nVidia Tegra
QuadSPI, Realtek RTL838x and RTL839x.
- Removal of obsolute EFM32, Txx9 and SIRF Prima and Atlas drivers.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmAq3M0ACgkQJNaLcl1U
h9Aq3gf6AuboDwFguKZAmXp27zjYsv5o5KtPyycTltIIfjGuA58+fN2zQT+puoGI
wzafjk9R73Foa67YKUwClaBGZNZbYOkB2iOk9a+/sku6k3jO14moybpMuL32dCVe
lutKd9D4n8/J5UHX3SHKHAZ9r2vp28rlaZa4wd79Ww5r+BLajUcrkjtr4GVT5k1k
WzzC0nUjE/zg1oV+PlakMolwK+iBCQYTT7S4r/OQAABQIkXXdtwmGvFUUXpGVF19
GUs52XI8QzK5504Xl+F7NF1+2zHovO11PTHnd+rAe6AfA/NGggtk6O1Y9R4tQHF9
TN6PHukNxUdTFfe6RTbSzPagpFydvQ==
=/4Ve
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The main focus of this release from a framework point of view has been
spi-mem where we've acquired support for a few new hardware features
which enable better performance on suitable hardware.
Otherwise mostly thanks to Arnd's cleanup efforts on old platforms
we've removed several obsolete drivers which just about balance out
the newer drivers we've added this cycle.
Summary:
- Allow drivers to flag if they are unidirectional.
- Support for DTR mode and hardware acceleration of dummy cycles in
spi-mem.
- Support for Allwinder H616, Intel Lightning Mountain, nVidia Tegra
QuadSPI, Realtek RTL838x and RTL839x.
- Removal of obsolete EFM32, Txx9 and SIRF Prima and Atlas drivers"
* tag 'spi-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (76 commits)
spi: Skip zero-length transfers in spi_transfer_one_message()
spi: dw: Avoid stack content exposure
spi: cadence-quadspi: Use spi_mem_dtr_supports_op()
spi: spi-mem: add spi_mem_dtr_supports_op()
spi: atmel-quadspi: Disable the QSPI IP at suspend()
spi: pxa2xx: Add IDs for the controllers found on Intel Lynxpoint
spi: pxa2xx: Fix the controller numbering for Wildcat Point
spi: Change provied to provided in the file spi.h
spi: mediatek: add set_cs_timing support
spi: support CS timing for HW & SW mode
spi: add power control when set_cs_timing
spi: stm32: make spurious and overrun interrupts visible
spi: stm32h7: replace private SPI_1HZ_NS with NSEC_PER_SEC
spi: stm32: defer probe for reset
spi: stm32: driver uses reset controller only at init
spi: stm32h7: ensure message are smaller than max size
spi: stm32: use bitfield macros
spi: stm32: do not mandate cs_gpio
spi: stm32: properly handle 0 byte transfer
spi: clps711xx: remove redundant white-space
...
BCM4908 uses fixed partitions layout but function of some partitions may
vary. Some devices use multiple firmware partitions and those partitions
should be marked to let system discover their purpose.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Richard Weinberger <richard@nod.at>
Single partition binding is quite common and may be:
1. Used by multiple parsers
2. Extended for more specific cases
Move it to separated file to avoid code duplication.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Convert the SPI-NOR binding to DT schema format. Like other memory chips,
the compatible strings are a mess with vendor prefixes not being used
consistently and some compatibles not documented. The resulting schema
passes on 'compatible' checks for most in tree users with the exception
of some oddballs.
I dropped the 'm25p.*-nonjedec' compatible strings as these don't appear
to be used anywhere.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210202175340.3902494-1-robh@kernel.org
Move the Documentation/devicetree/bindings/mtd/cadence-quadspi.txt to
Documentation/devicetree/bindings/spi/
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201124041840.31066-5-vadivel.muruganx.ramuthevar@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- Add vendor prefixes for bm, gpio-key, mentor, FII, and Ampere
- Add ADP5585/ADP5589 and delta,q54sj108a2 to trivial-devices.yaml
- Convert fixed-partitions, i2c-gate and fsl,dpaa2-console bindings to
schemas
- Drop PicoXcell bindings
- Drop unused and undocumented 'pnx,timeout' property from LPC32xx
- Add 'dynamic-power-coefficient' to Mali GPU bindings
- Make 'make dt_binding_check' not error out on warnings
- Various minor binding fixes
-----BEGIN PGP SIGNATURE-----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=FBOU
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Add vendor prefixes for bm, gpio-key, mentor, FII, and Ampere
- Add ADP5585/ADP5589 and delta,q54sj108a2 to trivial-devices.yaml
- Convert fixed-partitions, i2c-gate and fsl,dpaa2-console bindings to
schemas
- Drop PicoXcell bindings
- Drop unused and undocumented 'pnx,timeout' property from LPC32xx
- Add 'dynamic-power-coefficient' to Mali GPU bindings
- Make 'make dt_binding_check' not error out on warnings
- Various minor binding fixes
* tag 'devicetree-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (22 commits)
dt-bindings: mali-bifrost: Add dynamic-power-coefficient
dt-bindings: mali-midgard: Add dynamic-power-coefficient
dt-bindings: i2c: dw: cancel mandatory requirements for "#address-cells" and "#size-cells"
dt-bindings: Remove PicoXcell bindings
ARM: dts: lpc32xx: Remove unused and undocumented 'pnx,timeout'
dt-bindings: mtd: convert "fixed-partitions" to the json-schema
dt-bindings: vendor-prefixes: Add undocumented bm, gpio-key, and mentor prefixes
dt-bindings: pci: rcar-pci-ep: Document missing interrupts property
dt-bindings: vendor-prefixes: Add an entry for AmpereComputing.com
dt-bindings: vendor-prefixes: correct the spelling of TQ-Systems GmbH
dt-bindings: mfd: fix stm32 timers example
dt-bindings: trivial-devices: Add delta,q54sj108a2
dt-bindings:i2c:i2c-gate: txt to yaml conversion
dt-bindings: add ADP5585/ADP5589 entries to trivial-devices
dt-bindings: Correct GV11B GPU register sizes
dt-bindings: vendor-prefixes: Add FII
dt-bindings: Fix typo on the DesignWare IP reset bindings documentation
dt-bindings: Fix error in 'make dtbs_check' when using DT_SCHEMA_FILES
dt-bindings: arm: vt8500: remove redundant white-spaces
dt-bindings: fsl-imx-drm: fix example compatible string
...
This standardizes its documentation, allows validating with Makefile
checks and helps writing DTS files.
Noticeable changes:
1. Dropped "Partitions can be represented by sub-nodes of a flash
device." as we also support subpartitions (don't have to be part of
flash device node)
2. Dropped "to Linux" as bindings are meant to be os agnostic.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20201210172352.31632-1-zajec5@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
Driver requires different amount of clocks for different SoCs. Describe
these requirements properly to fix dtbs_check warnings like:
arch/arm64/boot/dts/freescale/imx8mm-beacon-kit.dt.yaml: nand-controller@33002000: clock-names:1: 'gpmi_apb' was expected
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201029162021.80839-1-krzk@kernel.org
This property does not describe very well its purpose: it describes
the ECC engine type. Deprecate it in favor of nand-ecc-engine which
points to either the NAND part itself in case of on-die ECC, or to the
parent node in case of an integrated ECC engine in the NAND controller
(previously referred as "hardware") or to another node in case of an
external controller. Other "modes" (none/software) are achieved with
the new nand-use-soft-ecc-engine and nand-no-ecc-engine properties.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201001102014.20100-3-miquel.raynal@bootlin.com
* Drop useless 'depends on' in Kconfig
* Add an extra level in the Kconfig hierarchy
* Trivial spellings
* Dynamic allocation of the interface configurations
* Dropping the default ONFI timing mode
* Various cleanup (types, structures, naming, comments)
* Hide the chip->data_interface indirection
* Add the generic rb-gpios property
* Add the ->choose_interface_config() hook
* Introduce nand_choose_best_sdr_timings()
* Use default values for tPROG_max and tBERS_max
* Avoid redefining tR_max and tCCS_min
* Add a helper to find the closest ONFI mode
* bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
* fsl-upm: Deprecation of specific DT properties
* fsl_upm: Driver rework and cleanup in favor of ->exec_op()
* Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
* brcmnand: ECC error handling on EDU transfers
* brcmnand: Don't default to EDU transfers
* qcom: Set BAM mode only if not set already
* qcom: Avoid write to unavailable register
* gpio: Driver rework in favor of ->exec_op()
* tango: ->exec_op() conversion
* mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
* toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
* toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
* toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
* hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
HyperBus changes:
* DMA support for TI's AM654 HyperBus controller driver.
* HyperBus frontend driver for Renesas RPC-IF driver.
SPI NOR core changes:
* Support for Winbond w25q64jwm flash
* Enable 4K sector support for mx25l12805d
SPI NOR controller drivers changes:
* intel-spi Add Alder Lake-S PCI ID
MTD Core changes:
* mtdoops: Don't run panic write twice
* mtdconcat: Correctly handle panic write
* Use DEFINE_SHOW_ATTRIBUTE
-----BEGIN PGP SIGNATURE-----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=X56H
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"NAND core changes:
- Drop useless 'depends on' in Kconfig
- Add an extra level in the Kconfig hierarchy
- Trivial spellings
- Dynamic allocation of the interface configurations
- Dropping the default ONFI timing mode
- Various cleanup (types, structures, naming, comments)
- Hide the chip->data_interface indirection
- Add the generic rb-gpios property
- Add the ->choose_interface_config() hook
- Introduce nand_choose_best_sdr_timings()
- Use default values for tPROG_max and tBERS_max
- Avoid redefining tR_max and tCCS_min
- Add a helper to find the closest ONFI mode
- bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
- fsl-upm: Deprecation of specific DT properties
- fsl_upm: Driver rework and cleanup in favor of ->exec_op()
- Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
- brcmnand: ECC error handling on EDU transfers
- brcmnand: Don't default to EDU transfers
- qcom: Set BAM mode only if not set already
- qcom: Avoid write to unavailable register
- gpio: Driver rework in favor of ->exec_op()
- tango: ->exec_op() conversion
- mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
- toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
- toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
- toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
- hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
HyperBus changes:
- DMA support for TI's AM654 HyperBus controller driver.
- HyperBus frontend driver for Renesas RPC-IF driver.
SPI NOR core changes:
- Support for Winbond w25q64jwm flash
- Enable 4K sector support for mx25l12805d
SPI NOR controller drivers changes:
- intel-spi Add Alder Lake-S PCI ID
MTD Core changes:
- mtdoops: Don't run panic write twice
- mtdconcat: Correctly handle panic write
- Use DEFINE_SHOW_ATTRIBUTE"
* tag 'mtd/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (76 commits)
mtd: hyperbus: Fix build failure when only RPCIF_HYPERBUS is enabled
mtd: hyperbus: add Renesas RPC-IF driver
Revert "mtd: spi-nor: Prefer asynchronous probe"
mtd: parsers: bcm63xx: Do not make it modular
mtd: spear_smi: Enable compile testing
mtd: maps: vmu-flash: fix typos for struct memcard
mtd: physmap: Add Baikal-T1 physically mapped ROM support
mtd: maps: vmu-flash: simplify the return expression of probe_maple_vmu
mtd: onenand: simplify the return expression of onenand_transfer_auto_oob
mtd: rawnand: cadence: remove a redundant dev_err call
mtd: rawnand: ams-delta: Fix non-OF build warning
mtd: rawnand: Don't overwrite the error code from nand_set_ecc_soft_ops()
mtd: rawnand: Introduce nand_set_ecc_on_host_ops()
mtd: rawnand: atmel: Check return values for nand_read_data_op
mtd: rawnand: vf610: Remove unused function vf610_nfc_transfer_size()
mtd: rawnand: qcom: Simplify with dev_err_probe()
mtd: rawnand: marvell: Fix and update kerneldoc
mtd: rawnand: marvell: Simplify with dev_err_probe()
mtd: rawnand: gpmi: Simplify with dev_err_probe()
mtd: rawnand: atmel: Simplify with dev_err_probe()
...
In order to add meta-schema checks for additional/unevaluatedProperties
being present, all schema need to make this explicit. As common/shared
schema are included by other schemas, they should always allow for
additionalProperties.
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201005183830.486085-5-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
This doesn't yet do anything in the tools, but make it explicit so we can
check either 'unevaluatedProperties' or 'additionalProperties' is present
in schemas.
'unevaluatedProperties' is appropriate when including another schema (via
'$ref') and all possible properties and/or child nodes are not
explicitly listed in the schema with the '$ref'.
This is in preparation to add a meta-schema to check for missing
'unevaluatedProperties' or 'additionalProperties'. This has been a
constant source of review issues.
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20201005183830.486085-2-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
DTSes with new i.MX 8M SoCs introduce their own compatibles so add them
to fix dtbs_check warnings like:
arch/arm64/boot/dts/freescale/imx8mm-evk.dt.yaml: nand-controller@33002000:
compatible:0: 'fsl,imx8mm-gpmi-nand' is not one of ['fsl,imx23-gpmi-nand', 'fsl,imx28-gpmi-nand', 'fsl,imx6q-gpmi-nand', 'fsl,imx6sx-gpmi-nand', 'fsl,imx7d-gpmi-nand']
From schema: Documentation/devicetree/bindings/mtd/gpmi-nand.yaml
arch/arm64/boot/dts/freescale/imx8mm-evk.dt.yaml: nand-controller@33002000:
compatible: ['fsl,imx8mm-gpmi-nand', 'fsl,imx7d-gpmi-nand'] is too long
arch/arm64/boot/dts/freescale/imx8mm-evk.dt.yaml: nand-controller@33002000:
compatible: Additional items are not allowed ('fsl,imx7d-gpmi-nand' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Document nand-use-soft-ecc-engine and nand-no-ecc-engine properties.
The former is here to force software correction, the latter prevents
any correction to happen.
These properties (along with nand-ecc-engine) are supposed to be more
accurate than the current nand-ecc-modes wich is very misleading and
very often people think it is mandatory while the core should be
relied upon to decide which correction to handle.
nand-ecc-mode was already inacurate, but it becomes totally
problematic with setups where there are several hardware engines.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-8-miquel.raynal@bootlin.com
This property is needed to precisely point to the hardware ECC engine
to use when there are several of them available. Here, hardware also
refers to the on-die possibility.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-7-miquel.raynal@bootlin.com
This optional property defines where the ECC bytes are expected to be
stored. No value defaults to an unknown location, while these
locations can be explicitly set to OOB or interleaved depending if
the ECC bytes are entirely stored in the OOB area or mixed with
regular data in the main area (also sometimes referred as
"syndrome").
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-6-miquel.raynal@bootlin.com
* Spelling
* http to https updates
NAND core changes:
* Drop useless 'depends on' in Kconfig
* Add an extra level in the Kconfig hierarchy
* Trivial spellings
* Dynamic allocation of the interface configurations
* Dropping the default ONFI timing mode
* Various cleanup (types, structures, naming, comments)
* Hide the chip->data_interface indirection
* Add the generic rb-gpios property
* Add the ->choose_interface_config() hook
* Introduce nand_choose_best_sdr_timings()
* Use default values for tPROG_max and tBERS_max
* Avoid redefining tR_max and tCCS_min
* Add a helper to find the closest ONFI mode
* bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
* fsl-upm: Deprecation of specific DT properties
* fsl_upm: Driver rework and cleanup in favor of ->exec_op()
* Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
* brcmnand: ECC error handling on EDU transfers
* brcmnand: Don't default to EDU transfers
* qcom: Set BAM mode only if not set already
* qcom: Avoid write to unavailable register
* gpio: Driver rework in favor of ->exec_op()
* tango: ->exec_op() conversion
* mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
* toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
* toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
* toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
* hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
SPI NOR core changes:
* Disable Quad Mode in spi_nor_restore().
* Don't abort BFPT parsing when QER reserved value is used.
* Add support/update capabilities for few flashes.
* Drop s70fl01gs flash: it does not support RDSR(05h) which
is critical for erase/write.
* Merge the SPIMEM DTR bits in spi-nor/next to avoid conflicts
during the release cycle.
SPI NOR controller drivers changes:
* Move the cadence-quadspi driver to spi-mem. The series was
taken through the SPI tree. Merge it also in spi-nor/next
to avoid conflicts during the release cycle.
* intel-spi:
- Add new PCI IDs.
- Ignore the Write Disable command, the controller doesn't
support it.
- Fix performance regression.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl8vJtMACgkQJWrqGEe9
VoRdGAf/Y5m5BwmLilkEYpffyxi7dVR6XOKPLU5EJXkS3dPvH9398zchbHOdedCZ
OzJIfh6Iv+qbkgS2g0lAAT+SAfOfG9plubvSdkjrHXl4eZXRnR/49RF5LAEju7sz
Uw1HdRcawyEi5uI9yYS0tCeVMIUJq+5x7VibH+82yOIdSPc60c7FDc5ih/nVKj/a
Pn9LOzGzkdndcE1b3FcF2Uk/T1YOJx3Yt5ngALlPpJxaDZmQSHtYPuuz8DfUbamf
uj3CkpqYRyT18CzuFvtuba6LyF+donXNJgvl6ivW7dlRSPzSMnDQu7J5bpNhUfcd
p/ZdzX1Jxle4theDm0J9ALsSSM5g2w==
=RiY8
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD core changes:
- Spelling
- http to https updates
NAND core changes:
- Drop useless 'depends on' in Kconfig
- Add an extra level in the Kconfig hierarchy
- Trivial spellings
- Dynamic allocation of the interface configurations
- Dropping the default ONFI timing mode
- Various cleanup (types, structures, naming, comments)
- Hide the chip->data_interface indirection
- Add the generic rb-gpios property
- Add the ->choose_interface_config() hook
- Introduce nand_choose_best_sdr_timings()
- Use default values for tPROG_max and tBERS_max
- Avoid redefining tR_max and tCCS_min
- Add a helper to find the closest ONFI mode
- bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
- fsl-upm: Deprecation of specific DT properties
- fsl_upm: Driver rework and cleanup in favor of ->exec_op()
- Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
- brcmnand: ECC error handling on EDU transfers
- brcmnand: Don't default to EDU transfers
- qcom: Set BAM mode only if not set already
- qcom: Avoid write to unavailable register
- gpio: Driver rework in favor of ->exec_op()
- tango: ->exec_op() conversion
- mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
- toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4,
TC58NVG0S3E, and TC58TEG5DCLTA00
- hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
SPI NOR core changes:
- Disable Quad Mode in spi_nor_restore().
- Don't abort BFPT parsing when QER reserved value is used.
- Add support/update capabilities for few flashes.
- Drop s70fl01gs flash: it does not support RDSR(05h) which is
critical for erase/write.
- Merge the SPIMEM DTR bits in spi-nor/next to avoid conflicts during
the release cycle.
SPI NOR controller drivers changes:
- Move the cadence-quadspi driver to spi-mem. The series was taken
through the SPI tree. Merge it also in spi-nor/next to avoid
conflicts during the release cycle.
- intel-spi:
- Add new PCI IDs.
- Ignore the Write Disable command, the controller doesn't support
it.
- Fix performance regression"
* tag 'mtd/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (79 commits)
MTD: pfow.h: drop a duplicated word
MTD: mtd-abi.h: drop a duplicated word
mtd: rawnand: omap_elm: Replace HTTP links with HTTPS ones
mtd: Replace HTTP links with HTTPS ones
mtd: hyperbus: Replace HTTP links with HTTPS ones
mtd: revert "spi-nor: intel: provide a range for poll_timout"
mtd: spi-nor: update read capabilities for w25q64 and s25fl064k
mtd: spi-nor: micron: Add SPI_NOR_DUAL_READ flag on mt25qu02g
mtd: spi-nor: macronix: Add support for mx66u2g45g
mtd: spi-nor: intel-spi: Simulate WRDI command
mtd: spi-nor: Disable the flash quad mode in spi_nor_restore()
mtd: spi-nor: Add capability to disable flash quad mode
mtd: spi-nor: spansion: Remove s70fl01gs from flash_info
mtd: spi-nor: sfdp: do not make invalid quad enable fatal
dt-bindings: mtd: fsl-upm-nand: Deprecate chip-delay and fsl, upm-wait-flags
mtd: rawnand: stm32_fmc2: get resources from parent node
mtd: rawnand: stm32_fmc2: use regmap APIs
memory: stm32-fmc2-ebi: add STM32 FMC2 EBI controller driver
dt-bindings: memory-controller: add STM32 FMC2 EBI controller documentation
dt-bindings: mtd: update STM32 FMC2 NAND controller documentation
...
* Drop useless 'depends on' in Kconfig
* Add an extra level in the Kconfig hierarchy
* Trivial spellings
* Dynamic allocation of the interface configurations
* Dropping the default ONFI timing mode
* Various cleanup (types, structures, naming, comments)
* Hide the chip->data_interface indirection
* Add the generic rb-gpios property
* Add the ->choose_interface_config() hook
* Introduce nand_choose_best_sdr_timings()
* Use default values for tPROG_max and tBERS_max
* Avoid redefining tR_max and tCCS_min
* Add a helper to find the closest ONFI mode
* bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
* fsl-upm: Deprecation of specific DT properties
* fsl_upm: Driver rework and cleanup in favor of ->exec_op()
* Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
* brcmnand: ECC error handling on EDU transfers
* brcmnand: Don't default to EDU transfers
* qcom: Set BAM mode only if not set already
* qcom: Avoid write to unavailable register
* gpio: Driver rework in favor of ->exec_op()
* tango: ->exec_op() conversion
* mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
* toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
* toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
* toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
* hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl8s85cACgkQJWrqGEe9
VoTrdwgAqphDYjtYNaI+1F0YQdIy/l8ddVmc5NwhKpiitKh0APDFDrdV5CwQaENO
9wWHJJPpT7xXPnEaq2+OWlPt2HpnEI4a+IRvySc9lr+MfkdY9ubo3B2wX7jBueKr
WoVDAGe8Ua1FkPOeDy7Qe+H1bQPha8fvyfb7x2h8uCYrrIkDJaMilorzHVnuXfCg
t5QJXRuznmYjUfMKOgLDjX3r79IJ+5mcrJIvMgHOyQIoG4Aao7lHIr2f01O50HWy
JKqQD3QhPR8lJGaEW485s+H+gnnNQW8Y1+8u3bhauEg/6Ddx2oksUIBTME8HUUuK
kAXrQ+KEs37l1a6pyaMBHaWU18T/oQ==
=hn04
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
Core changes:
* Drop useless 'depends on' in Kconfig
* Add an extra level in the Kconfig hierarchy
* Trivial spellings
* Dynamic allocation of the interface configurations
* Dropping the default ONFI timing mode
* Various cleanup (types, structures, naming, comments)
* Hide the chip->data_interface indirection
* Add the generic rb-gpios property
* Add the ->choose_interface_config() hook
* Introduce nand_choose_best_sdr_timings()
* Use default values for tPROG_max and tBERS_max
* Avoid redefining tR_max and tCCS_min
* Add a helper to find the closest ONFI mode
* bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
* fsl-upm: Deprecation of specific DT properties
* fsl_upm: Driver rework and cleanup in favor of ->exec_op()
* Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
* brcmnand: ECC error handling on EDU transfers
* brcmnand: Don't default to EDU transfers
* qcom: Set BAM mode only if not set already
* qcom: Avoid write to unavailable register
* gpio: Driver rework in favor of ->exec_op()
* tango: ->exec_op() conversion
* mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
* toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
* toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
* toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
* hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
These bindings can be used on SOCs where the FMC2 NAND controller is
in standalone. In case that the FMC2 embeds 2 controllers (an external
bus controller and a raw NAND controller), the register base address,
the clock and the reset will be defined in the parent node.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1591975362-22009-3-git-send-email-christophe.kerello@st.com
A few drivers use this property to describe GPIO pins used to sample
the NAND Ready/Busy state. Let's make it part of the generic binding
doc.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519232454.374081-2-boris.brezillon@collabora.com
The examples template is a 'simple-bus' with a size of 1 cell for
had between 2 and 4 cells which really only errors on I2C or SPI type
devices with a single cell.
The easiest fix in most cases is to change the 'reg' property to 1 cell
for address and size.
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Ezequiel Garcia <ezequiel@collabora.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: linux-rockchip@lists.infradead.org
Cc: linux-media@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Cc: netdev@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
* partition parser: Support MTD names containing one or more colons.
* mtdblock: clear cache_state to avoid writing to bad blocks repeatedly.
Raw NAND core changes:
* Stop using nand_release(), patched all drivers.
* Give more information about the ECC weakness when not matching the
chip's requirement.
* MAINTAINERS updates.
* Support emulated SLC mode on MLC NANDs.
* Support "constrained" controllers, adapt the core and ONFI/JEDEC
table parsing and Micron's code.
* Take check_only into account.
* Add an invalid ECC mode to discriminate with valid ones.
* Return an enum from of_get_nand_ecc_algo().
* Drop OOB_FIRST placement scheme.
* Introduce nand_extract_bits().
* Ensure a consistent bitflips numbering.
* BCH lib:
- Allow easy bit swapping.
- Rework a little bit the exported function names.
* Fix nand_gpio_waitrdy().
* Propage CS selection to sub operations.
* Add a NAND_NO_BBM_QUIRK flag.
* Give the possibility to verify a read operation is supported.
* Add a helper to check supported operations.
* Avoid indirect access to ->data_buf().
* Rename the use_bufpoi variables.
* Fix comments about the use of bufpoi.
* Rename a NAND chip option.
* Reorder the nand_chip->options flags.
* Translate obscure bitfields into readable macros.
* Timings:
- Fix default values.
- Add mode information to the timings structure.
Raw NAND controller driver changes:
* Fixed many error paths.
* Arasan
- New driver
* Au1550nd:
- Various cleanups
- Migration to ->exec_op()
* brcmnand:
- Misc cleanup.
- Support v2.1-v2.2 controllers.
- Remove unused including <linux/version.h>.
- Correctly verify erased pages.
- Fix Hamming OOB layout.
* Cadence
- Make cadence_nand_attach_chip static.
* Cafe:
- Set the NAND_NO_BBM_QUIRK flag
* cmx270:
- Remove this controller driver.
* cs553x:
- Misc cleanup
- Migration to ->exec_op()
* Davinci:
- Misc cleanup.
- Migration to ->exec_op()
* Denali:
- Add more delays before latching incoming data
* Diskonchip:
- Misc cleanup
- Migration to ->exec_op()
* Fsmc:
- Change to non-atomic bit operations.
* GPMI:
- Use nand_extract_bits()
- Fix runtime PM imbalance.
* Ingenic:
- Migration to exec_op()
- Fix the RB gpio active-high property on qi, lb60
- Make qi_lb60_ooblayout_ops static.
* Marvell:
- Misc cleanup and small fixes
* Nandsim:
- Fix the error paths, driver wide.
* Omap_elm:
- Fix runtime PM imbalance.
* STM32_FMC2:
- Misc cleanups (error cases, comments, timeout valus, cosmetic
changes).
SPI NOR core changes:
* Add, update support and fix few flashes.
* Prepare BFPT parsing for JESD216 rev D.
* Kernel doc fixes.
CFI changes:
* Support the absence of protection registers for Intel CFI flashes.
* Replace zero-length array with flexible-arrays.
-----BEGIN PGP SIGNATURE-----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=2M9Y
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- partition parser: Support MTD names containing one or more colons.
- mtdblock: clear cache_state to avoid writing to bad blocks
repeatedly.
Raw NAND core changes:
- Stop using nand_release(), patched all drivers.
- Give more information about the ECC weakness when not matching the
chip's requirement.
- MAINTAINERS updates.
- Support emulated SLC mode on MLC NANDs.
- Support "constrained" controllers, adapt the core and ONFI/JEDEC
table parsing and Micron's code.
- Take check_only into account.
- Add an invalid ECC mode to discriminate with valid ones.
- Return an enum from of_get_nand_ecc_algo().
- Drop OOB_FIRST placement scheme.
- Introduce nand_extract_bits().
- Ensure a consistent bitflips numbering.
- BCH lib:
- Allow easy bit swapping.
- Rework a little bit the exported function names.
- Fix nand_gpio_waitrdy().
- Propage CS selection to sub operations.
- Add a NAND_NO_BBM_QUIRK flag.
- Give the possibility to verify a read operation is supported.
- Add a helper to check supported operations.
- Avoid indirect access to ->data_buf().
- Rename the use_bufpoi variables.
- Fix comments about the use of bufpoi.
- Rename a NAND chip option.
- Reorder the nand_chip->options flags.
- Translate obscure bitfields into readable macros.
- Timings:
- Fix default values.
- Add mode information to the timings structure.
Raw NAND controller driver changes:
- Fixed many error paths.
- Arasan
- New driver
- Au1550nd:
- Various cleanups
- Migration to ->exec_op()
- brcmnand:
- Misc cleanup.
- Support v2.1-v2.2 controllers.
- Remove unused including <linux/version.h>.
- Correctly verify erased pages.
- Fix Hamming OOB layout.
- Cadence
- Make cadence_nand_attach_chip static.
- Cafe:
- Set the NAND_NO_BBM_QUIRK flag
- cmx270:
- Remove this controller driver.
- cs553x:
- Misc cleanup
- Migration to ->exec_op()
- Davinci:
- Misc cleanup.
- Migration to ->exec_op()
- Denali:
- Add more delays before latching incoming data
- Diskonchip:
- Misc cleanup
- Migration to ->exec_op()
- Fsmc:
- Change to non-atomic bit operations.
- GPMI:
- Use nand_extract_bits()
- Fix runtime PM imbalance.
- Ingenic:
- Migration to exec_op()
- Fix the RB gpio active-high property on qi, lb60
- Make qi_lb60_ooblayout_ops static.
- Marvell:
- Misc cleanup and small fixes
- Nandsim:
- Fix the error paths, driver wide.
- Omap_elm:
- Fix runtime PM imbalance.
- STM32_FMC2:
- Misc cleanups (error cases, comments, timeout valus, cosmetic
changes).
SPI NOR core changes:
- Add, update support and fix few flashes.
- Prepare BFPT parsing for JESD216 rev D.
- Kernel doc fixes.
CFI changes:
- Support the absence of protection registers for Intel CFI flashes.
- Replace zero-length array with flexible-arrays"
* tag 'mtd/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (208 commits)
mtd: clear cache_state to avoid writing to bad blocks repeatedly
mtd: parser: cmdline: Support MTD names containing one or more colons
mtd: physmap_of_gemini: remove defined but not used symbol 'syscon_match'
mtd: rawnand: Add an invalid ECC mode to discriminate with valid ones
mtd: rawnand: Return an enum from of_get_nand_ecc_algo()
mtd: rawnand: Drop OOB_FIRST placement scheme
mtd: rawnand: Avoid a typedef
mtd: Fix typo in mtd_ooblayout_set_databytes() description
mtd: rawnand: Stop using nand_release()
mtd: rawnand: nandsim: Reorganize ns_cleanup_module()
mtd: rawnand: nandsim: Rename a label in ns_init_module()
mtd: rawnand: nandsim: Manage lists on error in ns_init_module()
mtd: rawnand: nandsim: Fix the label pointing on nand_cleanup()
mtd: rawnand: nandsim: Free erase_block_wear on error
mtd: rawnand: nandsim: Use an additional label when freeing the nandsim object
mtd: rawnand: nandsim: Stop using nand_release()
mtd: rawnand: nandsim: Free the partition names in ns_free()
mtd: rawnand: nandsim: Free the allocated device on error in ns_init()
mtd: rawnand: nandsim: Free partition names on error in ns_init()
mtd: rawnand: nandsim: Fix the two ns_alloc_device() error paths
...
Add brcm,brcmnand-v2.1 and brcm,brcmnand-v2.2 as possible compatible
strings to support brcmnand controllers v2.1 and v2.2.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200522121524.4161539-5-noltari@gmail.com
Convert the ingenic,jz4780-nand.txt doc file to ingenic,nand.yaml.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a boolean property to force a specific partition attached to an MLC
NAND to be accessed in an emulated SLC mode this making this partition
immune to paired-pages corruptions.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200503155341.16712-6-miquel.raynal@bootlin.com
json-schema versions draft7 and earlier have a weird behavior in that
any keywords combined with a '$ref' are ignored (silently). The correct
form was to put a '$ref' under an 'allOf'. This behavior is now changed
in the 2019-09 json-schema spec and '$ref' can be mixed with other
keywords. The json-schema library doesn't yet support this, but the
tooling now does a fixup for this and either way works.
This has been a constant source of review comments, so let's change this
treewide so everyone copies the simpler syntax.
Scripted with ruamel.yaml with some manual fixups. Some minor whitespace
changes from the script.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for I2C
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for-iio
Reviewed-by: Stephen Boyd <sboyd@kernel.org> # clock
Signed-off-by: Rob Herring <robh@kernel.org>
Fix various inconsistencies in schema indentation. Most of these are
list indentation which should be 2 spaces more than the start of the
enclosing keyword. This doesn't matter functionally, but affects running
scripts which do transforms on the schema files.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
- Unit test for overlays with GPIO hogs
- Improve dma-ranges parsing to handle dma-ranges with multiple entries
- Update dtc to upstream version v1.6.0-2-g87a656ae5ff9
- Improve overlay error reporting
- Device link support for power-domains and hwlocks bindings
- Add vendor prefixes for Beacon, Topwise, ENE, Dell, SG Micro, Elida,
PocketBook, Xiaomi, Linutronix, OzzMaker, Waveshare Electronics, and
ITE Tech
- Add deprecated Marvell vendor prefix 'mrvl'
- A bunch of binding conversions to DT schema continues. Of note, the
common serial and USB connector bindings are converted.
- Add more Arm CPU compatibles
- Drop Mark Rutland as DT maintainer :(
-----BEGIN PGP SIGNATURE-----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=db/l
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Unit test for overlays with GPIO hogs
- Improve dma-ranges parsing to handle dma-ranges with multiple entries
- Update dtc to upstream version v1.6.0-2-g87a656ae5ff9
- Improve overlay error reporting
- Device link support for power-domains and hwlocks bindings
- Add vendor prefixes for Beacon, Topwise, ENE, Dell, SG Micro, Elida,
PocketBook, Xiaomi, Linutronix, OzzMaker, Waveshare Electronics, and
ITE Tech
- Add deprecated Marvell vendor prefix 'mrvl'
- A bunch of binding conversions to DT schema continues. Of note, the
common serial and USB connector bindings are converted.
- Add more Arm CPU compatibles
- Drop Mark Rutland as DT maintainer :(
* tag 'devicetree-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (106 commits)
MAINTAINERS: drop an old reference to stm32 pwm timers doc
MAINTAINERS: dt: update etnaviv file reference
dt-bindings: usb: dwc2: fix bindings for amlogic, meson-gxbb-usb
dt-bindings: uniphier-system-bus: fix warning in the example
dt-bindings: display: meson-vpu: fix indentation of reg-names' "items"
dt-bindings: iio: Fix adi, ltc2983 uint64-matrix schema constraints
dt-bindings: power: Fix example for power-domain
dt-bindings: arm: Add some constraints for PSCI nodes
of: some unittest overlays not untracked
of: gpio unittest kfree() wrong object
dt-bindings: phy: convert phy-rockchip-inno-usb2 bindings to yaml
dt-bindings: serial: sh-sci: Convert to json-schema
dt-bindings: serial: Document serialN aliases
dt-bindings: thermal: tsens: Set 'additionalProperties: false'
dt-bindings: thermal: tsens: Fix nvmem-cell-names schema
dt-bindings: vendor-prefixes: Add Beacon vendor prefix
dt-bindings: vendor-prefixes: Add Topwise
of: of_private.h: Replace zero-length array with flexible-array member
docs: dt: fix a broken reference to input.yaml
docs: dt: fix references to ap806-system-controller.txt
...
* Fix issue where write_cached_data() fails but write() still returns success
* maps: sa1100-flash: Replace zero-length array with flexible-array member
* phram: Fix a double free issue in error path
* Convert fallthrough comments into statements
* MAINTAINERS: Add the IRC channel to the MTD related subsystems
Raw NAND core changes:
* Add support for manufacturer specific suspend/resume operation
* Add support for manufacturer specific lock/unlock operation
* Replace zero-length array with flexible-array member
* Fix a typo ("manufecturer")
* Ensure nand_soft_waitrdy wait period is enough
Raw NAND controller driver changes:
* Brcmnand:
- Add support for flash-edu for dma transfers (+ bindings)
* Cadence:
- Reinit completion before executing a new command
- Change bad block marker size
- Fix the calculation of the avaialble OOB size
- Get meta data size from registers
* Qualcom:
- Use dma_request_chan() instead dma_request_slave_channel()
- Release resources on failure within qcom_nandc_alloc()
* Allwinner:
- Use dma_request_chan() instead dma_request_slave_channel()
* Marvell:
- Use dma_request_chan() instead dma_request_slave_channel()
- Release DMA channel on error
* Freescale:
- Use dma_request_chan() instead dma_request_slave_channel()
* Macronix:
- Add support for Macronix NAND randomizer (+ bindings)
* Ams-delta:
- Rename structures and functions to gpio_nand*
- Make the driver custom I/O ready
- Drop useless local variable
- Support custom driver initialisation
- Add module device tables
- Handle more GPIO pins as optional
- Make read pulses optional
- Don't hardcode read/write pulse widths
- Push inversion handling to gpiolib
- Enable OF partition info support
- Drop board specific partition info
- Use struct gpio_nand_platdata
- Write protect device during probe
* Ingenic:
- Use devm_platform_ioremap_resource()
- Add dependency on MIPS || COMPILE_TEST
* Denali:
- Deassert write protect pin
* ST:
- Use dma_request_chan() instead dma_request_slave_channel()
Raw NAND chip driver changes:
* Toshiba:
- Support reading the number of bitflips for BENAND (Built-in ECC NAND)
* Macronix:
- Add support for deep power down mode
- Add support for block protection
SPI-NAND core changes:
* Do not erase the block before writing a bad block marker
* Explicitly use MTD_OPS_RAW to write the bad block marker to OOB
* Stop using spinand->oobbuf for buffering bad block markers
* Rework detect procedure for different READ_ID operation
SPI-NAND driver changes:
* Toshiba:
- Support for new Kioxia Serial NAND
- Rename function name to change suffix and prefix (8Gbit)
- Add comment about Kioxia ID
* Micron:
- Add new Micron SPI NAND devices with multiple dies
- Add M70A series Micron SPI NAND devices
- identify SPI NAND device with Continuous Read mode
- Add new Micron SPI NAND devices
- Describe the SPI NAND device MT29F2G01ABAGD
- Generalize the OOB layout structure and function names
SPI NOR core changes:
* Move all the manufacturer specific quirks/code out of the core,
to make the core logic more readable and thus ease maintenance.
* Move the SFDP logic out of the core, it provides a better
separation between the SFDP parsing and core logic.
* Trim what is exposed in spi-nor.h. The SPI NOR controllers drivers
must not be able to use structures that are meant just for the
SPI NOR core.
* Use the spi-mem direct mapping API to let advanced controllers
optimize the read/write operations when they support direct mapping.
* Add generic formula for the Status Register block protection
handling. It fixes some long standing locking limitations and eases
the addition of the 4bit block protection support.
* Add block protection support for flashes with 4 block protection
bits in the Status Register.
SPI NOR controller drivers changes:
* The mtk-quadspi driver is replaced by the new spi-mem spi-mtk-nor
driver.
* Merge tag 'mtk-mtd-spi-move' into spi-nor/next to avoid conflicts.
HyperBus changes:
* Print error msg when compatible is wrong or missing
* Move mapping of direct access window from core to individual drivers
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl6GEU8ACgkQJWrqGEe9
VoSQ8gf/WV1vfxfAlgKRQ6WGkdrI+EndmciKx/sqf9KfAu6uNLHx3qcxQeibqvgC
KmIgJbCLXhgCUBZQLqyjqHtO3zImgPI2WWWR/tkieNaT9NT5jrAunYZpiqkCkjVD
HjML4iVcLwDJoHPZWTTTsFWd2cDLA8nFVXJQeaGRgdsx3j3D9OSOnfLGTUGfcg2H
lC0BxA6JRO7tdZlErqzy9BXUasjO5C7rsRzqgTiGT4h/H2yhYmDQhMW+Kz86zWiB
XdZsZJ2qLlTKntQmzR+30vbolId3iZqsO9q0mVkqWd2UQn5TpmmzNqLoYA6ys8KK
lW/1E53E3/Pq0+5ejGbD5m4afff+nw==
=/p2x
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD core changes:
- Fix issue where write_cached_data() fails but write() still returns
success
- maps: sa1100-flash: Replace zero-length array with flexible-array
member
- phram: Fix a double free issue in error path
- Convert fallthrough comments into statements
- MAINTAINERS: Add the IRC channel to the MTD related subsystems
Raw NAND core changes:
- Add support for manufacturer specific suspend/resume operation
- Add support for manufacturer specific lock/unlock operation
- Replace zero-length array with flexible-array member
- Fix a typo ("manufecturer")
- Ensure nand_soft_waitrdy wait period is enough
Raw NAND controller driver changes:
- Brcmnand:
* Add support for flash-edu for dma transfers (+ bindings)
- Cadence:
* Reinit completion before executing a new command
* Change bad block marker size
* Fix the calculation of the avaialble OOB size
* Get meta data size from registers
- Qualcom:
* Use dma_request_chan() instead dma_request_slave_channel()
* Release resources on failure within qcom_nandc_alloc()
- Allwinner:
* Use dma_request_chan() instead dma_request_slave_channel()
- Marvell:
* Use dma_request_chan() instead dma_request_slave_channel()
* Release DMA channel on error
- Freescale:
* Use dma_request_chan() instead dma_request_slave_channel()
- Macronix:
* Add support for Macronix NAND randomizer (+ bindings)
- Ams-delta:
* Rename structures and functions to gpio_nand*
* Make the driver custom I/O ready
* Drop useless local variable
* Support custom driver initialisation
* Add module device tables
* Handle more GPIO pins as optional
* Make read pulses optional
* Don't hardcode read/write pulse widths
* Push inversion handling to gpiolib
* Enable OF partition info support
* Drop board specific partition info
* Use struct gpio_nand_platdata
* Write protect device during probe
- Ingenic:
* Use devm_platform_ioremap_resource()
* Add dependency on MIPS || COMPILE_TEST
- Denali:
* Deassert write protect pin
- ST:
* Use dma_request_chan() instead dma_request_slave_channel()
Raw NAND chip driver changes:
- Toshiba:
* Support reading the number of bitflips for BENAND (Built-in ECC NAND)
- Macronix:
* Add support for deep power down mode
* Add support for block protection
SPI-NAND core changes:
- Do not erase the block before writing a bad block marker
- Explicitly use MTD_OPS_RAW to write the bad block marker to OOB
- Stop using spinand->oobbuf for buffering bad block markers
- Rework detect procedure for different READ_ID operation
SPI-NAND driver changes:
- Toshiba:
* Support for new Kioxia Serial NAND
* Rename function name to change suffix and prefix (8Gbit)
* Add comment about Kioxia ID
- Micron:
* Add new Micron SPI NAND devices with multiple dies
* Add M70A series Micron SPI NAND devices
* identify SPI NAND device with Continuous Read mode
* Add new Micron SPI NAND devices
* Describe the SPI NAND device MT29F2G01ABAGD
* Generalize the OOB layout structure and function names
SPI NOR core changes:
- Move all the manufacturer specific quirks/code out of the core, to
make the core logic more readable and thus ease maintenance.
- Move the SFDP logic out of the core, it provides a better
separation between the SFDP parsing and core logic.
- Trim what is exposed in spi-nor.h. The SPI NOR controllers drivers
must not be able to use structures that are meant just for the SPI
NOR core.
- Use the spi-mem direct mapping API to let advanced controllers
optimize the read/write operations when they support direct
mapping.
- Add generic formula for the Status Register block protection
handling. It fixes some long standing locking limitations and eases
the addition of the 4bit block protection support.
- Add block protection support for flashes with 4 block protection
bits in the Status Register.
SPI NOR controller drivers changes:
- The mtk-quadspi driver is replaced by the new spi-mem spi-mtk-nor
driver.
- Merge tag 'mtk-mtd-spi-move' into spi-nor/next to avoid conflicts.
HyperBus changes:
- Print error msg when compatible is wrong or missing
- Move mapping of direct access window from core to individual
drivers"
* tag 'mtd/for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (103 commits)
mtd: Convert fallthrough comments into statements
mtd: rawnand: toshiba: Support reading the number of bitflips for BENAND (Built-in ECC NAND)
MAINTAINERS: Add the IRC channel to the MTD related subsystems
mtd: Fix issue where write_cached_data() fails but write() still returns success
mtd: maps: sa1100-flash: Replace zero-length array with flexible-array member
mtd: phram: fix a double free issue in error path
mtd: spinand: toshiba: Support for new Kioxia Serial NAND
mtd: spinand: toshiba: Rename function name to change suffix and prefix (8Gbit)
mtd: rawnand: macronix: Add support for deep power down mode
mtd: rawnand: Add support for manufacturer specific suspend/resume operation
mtd: spi-nor: Enable locking for n25q512ax3/n25q512a
mtd: spi-nor: Add SR 4bit block protection support
mtd: spi-nor: Add generic formula for SR block protection handling
mtd: spi-nor: Set all BP bits to one when lock_len == mtd->size
mtd: spi-nor: controllers: aspeed-smc: Replace zero-length array with flexible-array member
mtd: spi-nor: Clear WEL bit when erase or program errors occur
MAINTAINERS: update entry after SPI NOR controller move
mtd: spi-nor: Trim what is exposed in spi-nor.h
mtd: spi-nor: Drop the MFR definitions
mtd: spi-nor: Get rid of the now empty spi_nor_ids[] table
...
* Add support for manufacturer specific suspend/resume operation
* Add support for manufacturer specific lock/unlock operation
* Replace zero-length array with flexible-array member
* Fix a typo ("manufecturer")
* Ensure nand_soft_waitrdy wait period is enough
Raw NAND controller driver changes:
* Brcmnand:
Add support for flash-edu for dma transfers (+ bindings)
* Cadence:
Reinit completion before executing a new command
Change bad block marker size
Fix the calculation of the avaialble OOB size
Get meta data size from registers
* Qualcom:
Use dma_request_chan() instead dma_request_slave_channel()
Release resources on failure within qcom_nandc_alloc()
* Allwinner:
Use dma_request_chan() instead dma_request_slave_channel()
* Marvell:
Use dma_request_chan() instead dma_request_slave_channel()
Release DMA channel on error
* Freescale:
Use dma_request_chan() instead dma_request_slave_channel()
* Macronix:
Add support for Macronix NAND randomizer (+ bindings)
* Ams-delta:
Rename structures and functions to gpio_nand*
Make the driver custom I/O ready
Drop useless local variable
Support custom driver initialisation
Add module device tables
Handle more GPIO pins as optional
Make read pulses optional
Don't hardcode read/write pulse widths
Push inversion handling to gpiolib
Enable OF partition info support
Drop board specific partition info
Use struct gpio_nand_platdata
Write protect device during probe
* Ingenic:
Use devm_platform_ioremap_resource()
Add dependency on MIPS || COMPILE_TEST
* Denali:
Deassert write protect pin
* ST:
Use dma_request_chan() instead dma_request_slave_channel()
Raw NAND chip driver changes:
* Toshiba:
Support reading the number of bitflips for BENAND (Built-in ECC NAND)
* Macronix:
Add support for deep power down mode
Add support for block protection
SPI-NAND core changes:
* Do not erase the block before writing a bad block marker
* Explicitly use MTD_OPS_RAW to write the bad block marker to OOB
* Stop using spinand->oobbuf for buffering bad block markers
* Rework detect procedure for different READ_ID operation
SPI-NAND driver changes:
* Toshiba:
Support for new Kioxia Serial NAND
Rename function name to change suffix and prefix (8Gbit)
Add comment about Kioxia ID
* Micron:
Add new Micron SPI NAND devices with multiple dies
Add M70A series Micron SPI NAND devices
identify SPI NAND device with Continuous Read mode
Add new Micron SPI NAND devices
Describe the SPI NAND device MT29F2G01ABAGD
Generalize the OOB layout structure and function names
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl5+XuIACgkQJWrqGEe9
VoRCAggAh0bpso9l8enk+ae1LrEGGLCV0sWMBy/pwM4zaBovqJqSdXRybg1IQE1N
5AvZrcQUBzdr9RzusB0J/xVC31gStjNQJROekArHJI6rzjoHRM/779fx0JV1JJHI
sWgX7UY7AVMH1l4BMB0mMezFeqJnZU5JRHQ+we3X4funNJ2JcBwvp1u4XJ2BDLRn
oCDLYgMC9S4lWEP7/ARgv27w7GfaegCUqNOHBVH75d2c+l476z5TKUap8s/LjI8u
8eRGerwLTj8/PLj1OqSEKXeJem2gZvZNpDCylgzrGZbU9r0M5I/EdXxJ90Pj6bR0
+G/0JHb4C1DXeDXzw79KisggHDkUUA==
=Zmzp
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.7' into mtd/next
Raw NAND core changes:
* Add support for manufacturer specific suspend/resume operation
* Add support for manufacturer specific lock/unlock operation
* Replace zero-length array with flexible-array member
* Fix a typo ("manufecturer")
* Ensure nand_soft_waitrdy wait period is enough
Raw NAND controller driver changes:
* Brcmnand:
Add support for flash-edu for dma transfers (+ bindings)
* Cadence:
Reinit completion before executing a new command
Change bad block marker size
Fix the calculation of the avaialble OOB size
Get meta data size from registers
* Qualcom:
Use dma_request_chan() instead dma_request_slave_channel()
Release resources on failure within qcom_nandc_alloc()
* Allwinner:
Use dma_request_chan() instead dma_request_slave_channel()
* Marvell:
Use dma_request_chan() instead dma_request_slave_channel()
Release DMA channel on error
* Freescale:
Use dma_request_chan() instead dma_request_slave_channel()
* Macronix:
Add support for Macronix NAND randomizer (+ bindings)
* Ams-delta:
Rename structures and functions to gpio_nand*
Make the driver custom I/O ready
Drop useless local variable
Support custom driver initialisation
Add module device tables
Handle more GPIO pins as optional
Make read pulses optional
Don't hardcode read/write pulse widths
Push inversion handling to gpiolib
Enable OF partition info support
Drop board specific partition info
Use struct gpio_nand_platdata
Write protect device during probe
* Ingenic:
Use devm_platform_ioremap_resource()
Add dependency on MIPS || COMPILE_TEST
* Denali:
Deassert write protect pin
* ST:
Use dma_request_chan() instead dma_request_slave_channel()
Raw NAND chip driver changes:
* Toshiba:
Support reading the number of bitflips for BENAND (Built-in ECC NAND)
* Macronix:
Add support for deep power down mode
Add support for block protection
SPI-NAND core changes:
* Do not erase the block before writing a bad block marker
* Explicitly use MTD_OPS_RAW to write the bad block marker to OOB
* Stop using spinand->oobbuf for buffering bad block markers
* Rework detect procedure for different READ_ID operation
SPI-NAND driver changes:
* Toshiba:
Support for new Kioxia Serial NAND
Rename function name to change suffix and prefix (8Gbit)
Add comment about Kioxia ID
* Micron:
Add new Micron SPI NAND devices with multiple dies
Add M70A series Micron SPI NAND devices
identify SPI NAND device with Continuous Read mode
Add new Micron SPI NAND devices
Describe the SPI NAND device MT29F2G01ABAGD
Generalize the OOB layout structure and function names
spi-mtk-nor is a driver to replace mtk-quadspi and they have almost
the same device-tree bindings. Reuse this binding documentation and
convert it for new driver:
1. "Mediatek SoCs" -> "Mediatek ARM SoCs" because MTK MIPS SoCs
use different controllers.
2. document "interrupts" as a required property because it's
available on all SoCs with this controller and new driver takes
advantages of it. It's implemented as optional only to maintain
backward compatibility.
3. add a dummy interrupt binding in example.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20200306085052.28258-4-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are several DT doc references that require manual fixes.
I found 3 cases fixed on this patch:
- directory named "binding/" instead of "bindings/";
- .txt to .yaml renames;
- file renames (still on txt format);
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
According to the Denali NAND Flash Memory Controller User's Guide,
this IP has two reset signals.
rst_n: reset most of FFs in the controller core
reg_rst_n: reset all FFs in the register interface, and in the
initialization sequencer
This commit specifies these reset signals.
It is possible to control them separately from the IP point of view
although they might be often tied up together in actual SoC integration.
At least for the upstream platforms, Altera/Intel SOCFPGA and Socionext
UniPhier, the reset controller seems to provide only 1-bit control for
the NAND controller. If it is the case, the resets property should
reference to the same phandles for "nand" and "reg" resets, like this:
resets = <&nand_rst>, <&nand_rst>;
reset-names = "nand", "reg";
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
While my email address has changed for a while, all the schemas I
contributed still have the old one unfortunately. Update it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Rob Herring <robh@kernel.org>
- DT schemas for PWM, syscon, power domains, SRAM, syscon-reboot,
syscon-poweroff, renesas-irqc, simple-pm-bus, renesas-bsc, pwm-rcar,
Renesas tpu, at24 eeprom, rtc-sh, Allwinner PS/2, sharp,ld-d5116z01b
panel, Arm SMMU, max77650, Meson CEC, Amlogic canvas and DWC3 glue,
Allwinner A10 mUSB and CAN, TI Davinci MDIO, QCom QCS404 interconnect,
Unisoc/Spreadtrum SoCs and UART
- Convert a bunch of Samsung bindings to DT schema
- Convert a bunch of ST stm32 bindings to DT schema
- Realtek and Exynos additions to Arm Mali bindings
- Fix schema errors in RiscV CPU schema
- Various schema fixes from improved meta-schema checks
- Improve the handling of 'dma-ranges' and in particular fix DMA mask
setup on PCI bridges
- Fix a memory leak in add_changeset_property() and DT unit tests.
- Several documentation improvements for schema validation
- Rework build rules to improve schema validation errors
- Color output for dtx_diff
-----BEGIN PGP SIGNATURE-----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=L6uq
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- DT schemas for PWM, syscon, power domains, SRAM, syscon-reboot,
syscon-poweroff, renesas-irqc, simple-pm-bus, renesas-bsc, pwm-rcar,
Renesas tpu, at24 eeprom, rtc-sh, Allwinner PS/2, sharp,ld-d5116z01b
panel, Arm SMMU, max77650, Meson CEC, Amlogic canvas and DWC3 glue,
Allwinner A10 mUSB and CAN, TI Davinci MDIO, QCom QCS404
interconnect, Unisoc/Spreadtrum SoCs and UART
- Convert a bunch of Samsung bindings to DT schema
- Convert a bunch of ST stm32 bindings to DT schema
- Realtek and Exynos additions to Arm Mali bindings
- Fix schema errors in RiscV CPU schema
- Various schema fixes from improved meta-schema checks
- Improve the handling of 'dma-ranges' and in particular fix DMA mask
setup on PCI bridges
- Fix a memory leak in add_changeset_property() and DT unit tests.
- Several documentation improvements for schema validation
- Rework build rules to improve schema validation errors
- Color output for dtx_diff
* tag 'devicetree-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (138 commits)
libfdt: define INT32_MAX and UINT32_MAX in libfdt_env.h
dt-bindings: arm: Remove leftover axentia.txt
of: unittest: fix memory leak in attach_node_and_children
of: overlay: add_changeset_property() memory leak
dt-bindings: interrupt-controller: arm,gic-v3: Add missing type to interrupt-partition-* nodes
dt-bindings: firmware: ixp4xx: Drop redundant minItems/maxItems
dt-bindings: power: Rename back power_domain.txt bindings to fix references
dt-bindings: i2c: stm32: Migrate i2c-stm32 documentation to yaml
dt-bindings: mtd: Convert stm32 fmc2-nand bindings to json-schema
dt-bindings: remoteproc: convert stm32-rproc to json-schema
dt-bindings: mailbox: convert stm32-ipcc to json-schema
dt-bindings: mfd: Convert stm32 low power timers bindings to json-schema
dt-bindings: interrupt-controller: Convert stm32-exti to json-schema
dt-bindings: crypto: Convert stm32 HASH bindings to json-schema
dt-bindings: rng: Convert stm32 RNG bindings to json-schema
dt-bindings: pwm: Convert Samsung PWM bindings to json-schema
dt-bindings: pwm: Convert PWM bindings to json-schema
dt-bindings: serial: Add a new compatible string for SC9863A
dt-bindings: serial: Convert sprd-uart to json-schema
dt-bindings: arm: Add bindings for Unisoc SC9863A
...
Convert the STM32 fmc2-nand binding to DT schema format using json-schema
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
CC: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
* Useless extra checks dropped.
* Updated the detection of the bad block markers position
Raw NAND controller drivers:
* Cadence : New driver
* Brcmnand: Support for flash-dma v0 + fixes
* Denali : Support for the legacy controller/chip DT representation
dropped
* Superfluous dev_err() calls removed
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl3KwQYACgkQJWrqGEe9
VoTj1wf/Zvnk1u2vNVUaWDaHnUTAcMvjYNr1N1ppXquRXQTknZHxcgqavcwOA3yV
inHRdjQpvTPft3Pb0tddC2VBOMQTYWDGJs6JOLiPF5c4QdW/w4yHRrdnEIumbVP/
itXySbPj2QsXcRuIoEm165NTI8mdSzZFixZvCNS58r2mvMXvQbcUHsP9vjlUs9/S
XPqBlSBPKa6hC2ToIiXhgkGDQzVJ/OkCOSgG+37ATUrEqWUi9oN2KUPkbk4HSZe9
dntUIFSjeAqGjKGRGwAlt4axhnFWABfWa9xBwX9k5s4mt/FJ9QF24geemz/F1Ljp
7xd6MJu3JYoW8qBcXRRDgHuv5RNnHA==
=rpUJ
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.5' into mtd/next
Raw NAND core
* Useless extra checks dropped.
* Updated the detection of the bad block markers position
Raw NAND controller drivers:
* Cadence : New driver
* Brcmnand: Support for flash-dma v0 + fixes
* Denali : Support for the legacy controller/chip DT representation
dropped
* Superfluous dev_err() calls removed
This adds device tree bindings for the Intel IXP4xx
flash controller, a simple physmap which however need a
specific big-endian or mixed-endian access pattern to the
memory.
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Document the bindings used by Cadence NAND controller driver
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Document the bindings used by the Macronix raw NAND controller.
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Properties which are child node definitions need to have an explict
type. Otherwise, a matching (DT) property can silently match when an
error is desired. Fix this up tree-wide. Once this is fixed, the
meta-schema will enforce this on any child node definitions.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-spi@vger.kernel.org
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
MTD core changes:
- New Hyperbus framework
- New _is_locked (concat) implementation
- Various cleanups
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
* fix BCH ECC layout for large page NAND parts
* fallback to detected ecc-strength, ecc-step-size
* when oops in progress use pio and interrupt polling
* code refactor code to introduce helper functions
* add support for v7.3 controller
- FSMC:
* use nand_op_trace for operation tracing
- GPMI:
* move all driver code into single file
* various cleanups (including dmaengine changes)
* use runtime PM to manage clocks
* implement exec_op
- MTK:
* correct low level time calculation of r/w cycle
* improve data sampling timing for read cycle
* add validity check for CE# pin setting
* fix wrongly assigned OOB buffer pointer issue
* re-license MTK NAND driver as Dual MIT/GPL
- STM32:
* manage the get_irq error case
* increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl0qLr4ACgkQJWrqGEe9
VoQVCwf/ZCG5CldS3cs6B68kMJoZ/rJyJxBnxtIhffda2vw1KG/12o6XaDO9xA/R
EwYrOTzlYZxzCZsNvWyHepG3Kj3d38CJ52ZqhavjpihwMlKKOgW/K39xuKWCrfxS
sVMLz/UdrcsQfcPGAy7DSyqhzRAtupNxngCdEkIIMGFZWsv4uZfOFEGMrzUJ5RYN
/okIyUE7Iz0dRq1/KXSl365V1MS8QP2eHFuHrUd38+kJ8TJnQjXX3Bmdul4aNTx+
HIIpykovoAn5BZ0YA4lJL90zVoDOWysARwHIAMDvJa8zS0wDTU16Tj2M6AQK+a4x
hbIOOkeX0hTKpJvy7/khli5y1bn2mw==
=L+tV
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"This contains the following changes for MTD:
MTD core changes:
- New Hyperbus framework
- New _is_locked (concat) implementation
- Various cleanups
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
- fix BCH ECC layout for large page NAND parts
- fallback to detected ecc-strength, ecc-step-size
- when oops in progress use pio and interrupt polling
- code refactor code to introduce helper functions
- add support for v7.3 controller
- FSMC:
- use nand_op_trace for operation tracing
- GPMI:
- move all driver code into single file
- various cleanups (including dmaengine changes)
- use runtime PM to manage clocks
- implement exec_op
- MTK:
- correct low level time calculation of r/w cycle
- improve data sampling timing for read cycle
- add validity check for CE# pin setting
- fix wrongly assigned OOB buffer pointer issue
- re-license MTK NAND driver as Dual MIT/GPL
- STM32:
- manage the get_irq error case
- increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control"
* tag 'mtd/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (60 commits)
mtd: concat: implement _is_locked mtd operation
mtd: concat: refactor concat_lock/concat_unlock
mtd: abi: do not use C++ style comments in uapi header
mtd: afs: remove unneeded NULL check
mtd: rawnand: stm32_fmc2: increase DMA completion timeouts
mtd: rawnand: Use kzalloc() instead of kmalloc() and memset()
mtd: hyperbus: Add driver for TI's HyperBus memory controller
mtd: spinand: read returns badly if the last page has bitflips
mtd: spinand: Add initial support for Paragon PN26G0xA
mtd: rawnand: mtk: Re-license MTK NAND driver as Dual MIT/GPL
mtd: rawnand: gpmi: remove double assignment to block_size
dt-bindings: mtd: brcmnand: Add brcmnand, brcmnand-v7.3 support
mtd: rawnand: brcmnand: Add support for v7.3 controller
mtd: rawnand: brcmnand: Refactored code to introduce helper functions
mtd: rawnand: brcmnand: When oops in progress use pio and interrupt polling
mtd: Add flag to indicate panic_write
mtd: rawnand: Add Macronix NAND read retry support
mtd: onenand: Avoid fall-through warnings
mtd: spinand: Add support for GigaDevice GD5F1GQ4UFxxG
mtd: spinand: Add support for two-byte device IDs
...
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl0V1XYACgkQS1VPR6WN
FOkBbQf+Iv2+vmoDGDCVGO4LZh+N/l0Sh/C31hJj5y7GVkCdwMJCvdOrGEhDkseu
Dc0gchT6uy52pAp4N0B88avC8fSJY0UwFRbnqUUA546R9Uf6h+gbGIZCX/rzZuIi
IDDNHc06qbpxpesfC5CowhY49QVGG+O0scgUOE2gKHOfd04kXu6gqIV0BvQZg80R
EpSgifHLUk/b2015FyqB5YFuc2K3HMmcWc6uJx4kSHPCXiCOx8aaEqjKvK9vL0h5
XOxXim5HhuzFqQ8vSPqvnKDokkuV3pcSUcaQyjQjrebTlectaDjGZlLF17Udm9Q9
I0zI+7deXK9L4roatEryzOdW0Ql3Hw==
=J5Uw
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.3-v2' of gitolite.kernel.org:pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
* fix BCH ECC layout for large page NAND parts
* fallback to detected ecc-strength, ecc-step-size
* when oops in progress use pio and interrupt polling
* code refactor code to introduce helper functions
* add support for v7.3 controller
- FSMC:
* use nand_op_trace for operation tracing
- GPMI:
* move all driver code into single file
* various cleanups (including dmaengine changes)
* use runtime PM to manage clocks
* implement exec_op
- MTK:
* correct low level time calculation of r/w cycle
* improve data sampling timing for read cycle
* add validity check for CE# pin setting
* fix wrongly assigned OOB buffer pointer issue
* re-license MTK NAND driver as Dual MIT/GPL
- STM32:
* manage the get_irq error case
* increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl0fxH8ACgkQJWrqGEe9
VoRq5wgApOTmT44UiI3XHQZMWANcW5/DkNwXEzXtdRQJHv1m3eqny1faGOYJZifZ
eb0TpohK0783L4STii7g1iplBA+c8UGJaS1bpn9HoN3us8wxXn51fzHHj5G3z2tR
xoyaEm7w7dZuqe/FLCW+MbtOREAq1GzullVZxrd75wxNyK3cQXawqYDsil6I5fl7
sf2zMzfzfGK6LqbapOHorxyI8yJR712TLPwBq7amHpPZMXOny0gIlYVXLv6jYAfr
3RcW0YpyplBjLAFKBOpVLPJ61c9NVQSsdQ2wviRckhrMgCD83f7YDmAACxM0rvSz
lVYcHHqoqYHlTDPVBebeoifQOb4uUw==
=I5Hg
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
* fix BCH ECC layout for large page NAND parts
* fallback to detected ecc-strength, ecc-step-size
* when oops in progress use pio and interrupt polling
* code refactor code to introduce helper functions
* add support for v7.3 controller
- FSMC:
* use nand_op_trace for operation tracing
- GPMI:
* move all driver code into single file
* various cleanups (including dmaengine changes)
* use runtime PM to manage clocks
* implement exec_op
- MTK:
* correct low level time calculation of r/w cycle
* improve data sampling timing for read cycle
* add validity check for CE# pin setting
* fix wrongly assigned OOB buffer pointer issue
* re-license MTK NAND driver as Dual MIT/GPL
- STM32:
* manage the get_irq error case
* increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
Mixing 'maxItems' and scalar properties doesn't make much sense, so drop
'maxItems' as a single item is implied.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-mtd@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Added brcm,brcmnand-v7.3 as possible compatible string to support
brcmnand controller v7.3.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand-ecc-strength and nand-ecc-step-size can be made optional as
brcmnand driver can support using raw NAND layer detected values.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The QSPI module can have an optional reset signals that will hold the
module in a reset state.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
There's a new driver using the SPI memory interface of the
SPI framework at spi/spi-stm32-qspi.c, which can be used
together with m25p80.c to replace the functionality of
this SPI NOR driver.
The "new" driver uses the same dt properties and not affects
the legacy compatibility.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
nand-controller.yaml replaced nand.txt however the references to it were
not updated. This change updates these references wherever it appears in
bindings documentation.
Fixes: 212e496935 ("dt-bindings: mtd: Add YAML schemas for the generic NAND options")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This adds device tree bindings for ARM Firmware Suite
flash partitioning used in NOR flashes on ARM reference
designs.
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Add an example showing how to use the addr-gpios property to deal with a
system with limited IO space.
Cc: devicetree@vger.kernel.org
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Describe how to use the BCM963XX ImageTag format in a mixed flash layout
environment.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Add binding documentation for the standard CFE based BCM963XX flash
layout, found in most devices using a BCM63XX SoC with NOR flash.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The A23/A33 NAND controller is slightly different than the A10+ ones,
eg. DMA handling is a bit different and a few register offsets
changed.
Introduce a new compatible to represent this version of the IP.
Also append '-controller' to the new compatible (which is required for
new compatibles) as this is describing a NAND controller and not a
NAND chip.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Switch the DT binding to a YAML schema to enable the DT validation.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The NAND chips in MTD have a bunch of generic options that are needed in a
device tree. Add a YAML schemas for those.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently, this driver sticks to the legacy NAND model because it was
upstreamed before commit 2d472aba15 ("mtd: nand: document the NAND
controller/NAND chip DT representation"). However, relying on the
dummy_controller is already deprecated.
Switch over to the new controller/chip representation.
The struct denali_nand_info has been split into denali_controller
and denali_chip, to contain the controller data, per-chip data,
respectively.
One problem is, this commit changes the DT binding. So, as always,
the backward compatibility must be taken into consideration.
In the new binding, the controller node expects
#address-cells = <1>;
#size-cells = <0>;
... since the child nodes represent NAND chips.
In the old binding, the controller node may have subnodes, but they
are MTD partitions.
The denali_dt_is_legacy_binding() exploits it to distinguish old/new
platforms.
Going forward, the old binding is only allowed for existing DT files.
I updated the binding document.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The 'ingenic,bch-controller' property is now deprecated and the
'ecc-engine' property should be used instead.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The JZ4740 ECC hardware is not BCH but Reed-Solomon, so it makes more
sense to use the more generic ECC term.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add compatible strings to probe the jz4780-nand and jz4780-bch drivers
from devicetree on the JZ4725B and JZ4740 SoCs from Ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
A fairly quiet release for SPI, the biggest thing is the conversion to
use GPIO descriptors which is now 90% done but still needs some
stragglers converting.
- Support for inter-word delays.
- Conversion of the core and most drivers to use GPIO descriptors for
GPIO controlled chip selects.
- New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlx9WtETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DfrB/92O47HJfHg1xIgOp4BLzT8lA5zQEsy
a8ApcLVLvY6mSfbB/G7RosfoPwTc1eZP5Q2BqzQOBIO+507ao4AcASARmkTwjwkC
eRUJ/THkGyGurs8POtnc5YJlHsT1t743QpqlUNekt+NqognlkPccgc5bNgixfuPD
eVSwVC85SKP3gCpAjVb6FFFmlWr8AKdlgx+41h9QpMNG/85H6xgo4C4Wlajt42/E
wNx+WXzlPyzB5Lc3IGPeF/I/Hu/Ta3hUZLTVpWi5ubM8p4SYGmMZ9l8sURPCz1pK
UMZFpJxx8DWwkj2F/FkoLasfiRqUHIP9K7NfKF0u2xdNbhEk1GA3NAG0
=ctKG
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, the biggest thing is the conversion to
use GPIO descriptors which is now 90% done but still needs some
stragglers converting.
Summary:
- Support for inter-word delays
- Conversion of the core and most drivers to use GPIO descriptors for
GPIO controlled chip selects
- New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum"
* tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (104 commits)
spi: sh-msiof: Restrict bits per word to 8/16/24/32 on R-Car Gen2/3
spi: sifive: Remove redundant dev_err call in sifive_spi_probe()
spi: sifive: Remove spi_master_put in sifive_spi_remove()
spi: spi-gpio: fix SPI_CS_HIGH capability
spi: pxa2xx: Setup maximum supported DMA transfer length
spi: sifive: Add driver for the SiFive SPI controller
spi: sifive: Add DT documentation for SiFive SPI controller
spi: sprd: Add a prefix for SPI DMA channel macros
spi: sprd: spi: sprd: Add DMA mode support
dt-bindings: spi: Add the DMA properties for the SPI dma mode
spi: sprd: Add the SPI irq function for the SPI DMA mode
dt-bindings: spi: imx: Add an entry for the i.MX8QM compatible
spi: use gpio[d]_set_value_cansleep for setting chipselect GPIO
spi: gpio: Advertise support for SPI_CS_HIGH
spi: sh-msiof: Replace spi_master by spi_controller
spi: sh-hspi: Replace spi_master by spi_controller
spi: rspi: Replace spi_master by spi_controller
spi: atmel-quadspi: add support for sam9x60 qspi controller
dt-bindings: spi: atmel-quadspi: QuadSPI driver for Microchip SAM9X60
spi: atmel-quadspi: add support for named peripheral clock
...
- Fourth batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Checking the return code of nand_reset() and nand_readid_op().
- Removing ->legacy.erase and single_erase().
- Simplifying the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fixing various possible object reference leaks (MTK, JZ4780, Atmel).
- ST:
* Adding support for STM32 FMC2 NAND flash controller.
- Meson:
* Adding support for Amlogic NAND flash controller.
- Denali:
* Several cleanup patches.
- Sunxi:
* Several cleanup patches.
- FSMC:
* Disabling NAND on remove().
* Resetting NAND timings on resume().
SPI-NAND drivers changes:
- Toshiba:
* Adding support for all Toshiba products.
- Macronix:
* Fixing ECC status read.
- Gigadevice:
* Adding support for GD5F1GQ4UExxG.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAlxwE4kACgkQJWrqGEe9
VoRQVQf+OOkScM6ZbsO2GbMRe0ybMOCOyBXfojPEGtVv80gHHrAPRocLqWMB1Xdb
MSfm7j+lyZU1I8eYVvdYXby7s5FlVWbrh8NSnnwox1QusdmyBm7vcxc6st15Poy/
/WtjE+Cry49eIx5L/pmmNH3AIqMdvSRTJD7NgOYjo/SIq4GLR+KQEgt1VLp/KyO0
TGeMDIT3Q3+MXVwvUh3YlHUwNJ2jOpjpPW94QxD0mef/b9doUlkvrOdHs3JeGQzX
aiiqWI1nRBmjNs34wp7Dyf3G/feplKyi+IS/ghTiijAgwbWdRI7KxrPtyCUYiint
3XqVgZAF/sfFaKFMIiJBMzoLQB15dQ==
=VbaE
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.1' of git://git.infradead.org/linux-mtd into mtd/next
NAND core changes:
- Fourth batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Checking the return code of nand_reset() and nand_readid_op().
- Removing ->legacy.erase and single_erase().
- Simplifying the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fixing various possible object reference leaks (MTK, JZ4780, Atmel).
- ST:
* Adding support for STM32 FMC2 NAND flash controller.
- Meson:
* Adding support for Amlogic NAND flash controller.
- Denali:
* Several cleanup patches.
- Sunxi:
* Several cleanup patches.
- FSMC:
* Disabling NAND on remove().
* Resetting NAND timings on resume().
SPI-NAND drivers changes:
- Toshiba:
* Adding support for all Toshiba products.
- Macronix:
* Fixing ECC status read.
- Gigadevice:
* Adding support for GD5F1GQ4UExxG.
AM654 SoC has Cadence Octal SPI controller, which is similar to Cadence
QSPI controller but supports Octal IO(x8 data lines) and Double Data
Rate(DDR) mode. Add new compatible to support OSPI controller on TI's
AM654 SoCs.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Add Amlogic NAND controller dt-bindings for Meson SoC,
Current this driver support GXBB/GXL/AXG platform.
Signed-off-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This updates bindings for the MT7629 SPI-NOR controller.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
This patch adds the documentation of the device tree bindings for the STM32
FMC2 NAND controller.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Move the documentation of the old SPI NOR driver to the place of the new
SPI memory interface based driver.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The main thing this release has been a lot of work on the integration
with SPI NOR flashes, there's been some specific support for a while for
controller features designed to make them perform better but it's not
worked out as well as hoped so the interface has been redesigned in a
way that will hopefully do better - it's already been adopted by a
number of additional controllers so things are looking good. Otherwise
most of the work has been driver specific:
- Support for better integration with NOR flashes from Boris Brezillon
and Yogesh Narayan Gaur plus usage of it in several drivers.
- A big cleanup of the Rockchip driver from Emil Renner Berthing.
- Lots of performance improvements for bcm2835 from Lukas Wunner.
- Slave mode support for pxa2xx from Lubomir Rintel.
- Support for Macronix MXIC, Mediatek MT7629 and MT8183, NPCM PSPI,
and Renesas r8a77470.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlwhLBsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0AGvB/9odNqLjVJiG6v0EIKqLyYXMzCYgmrZ
RyBZoqTKoNmXxv0b/Fdsi8VaiJ8x2WIcqLzhpQlg3twOCvXQbgoA+JzQNyHZlZ1u
8cxfFGebVS6r0k14bkmAVR8LSvGlReOZQLC2MvccVc/UAwN0/p5ncN0xUADHvIOW
/Pmx0/e2uCMx1+OMAudlUXQ5IIbnb5/OjvDfR/7tlVo5YKSgkHBJeunOYSaPSNuO
QNf9+kZxvQ8djYbpYqqHWovPF7JSlQAj0WkMJPB/g3R09E/vatSBlCMnETBJWn/L
wogHquLK/vwRaS+MqTSrGsi0ylpqgxmZrbGKcXKF51fim0EvBg7cMqe6
=ZnI3
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The main thing this release has been a lot of work on the integration
with SPI NOR flashes, there's been some specific support for a while
for controller features designed to make them perform better but it's
not worked out as well as hoped so the interface has been redesigned
in a way that will hopefully do better - it's already been adopted by
a number of additional controllers so things are looking good.
Otherwise most of the work has been driver specific:
- Support for better integration with NOR flashes from Boris
Brezillon and Yogesh Narayan Gaur plus usage of it in several
drivers.
- A big cleanup of the Rockchip driver from Emil Renner Berthing.
- Lots of performance improvements for bcm2835 from Lukas Wunner.
- Slave mode support for pxa2xx from Lubomir Rintel.
- Support for Macronix MXIC, Mediatek MT7629 and MT8183, NPCM PSPI,
and Renesas r8a77470"
* tag 'spi-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (90 commits)
spi: sh-msiof: Reduce the number of times write to and perform the transmission from FIFO
spi: sh-msiof: Add r8a774c0 support
doc: lpspi: Document DT bindings for LPSPI slave mode
spi: lpspi: Let watermark change with send data length
spi: lpspi: Add slave mode support
spi: lpspi: Replace all "master" with "controller"
spi: imx: drop useless member speed_hz from driver data struct
spi: imx: rename config callback and add useful parameters
spi: imx: style fixes
spi: imx: mx51-ecspi: Move some initialisation to prepare_message hook.
spi: imx: add a device specific prepare_message callback
mtd: atmel-quadspi: disallow building on ebsa110
spi: Update NPCM PSPI controller documentation
spi: npcm: Modify pspi send function
spi: Use of_node_name_eq for node name comparisons
spi: dw-mmio: add ACPI support
spi: bcm2835: Synchronize with callback on DMA termination
spi: bcm2835: Speed up FIFO access if fill level is known
spi: bcm2835: Polish transfer of DMA prologue
spi: spi-mem: add support for octal mode I/O data transfer
...
This adds device tree bindings for the RedBoot FIS partition
format.
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Atmel SAMA5D2 QuadSPI driver was moved from mtd to spi subsystem,
this change is just moving DT-binding documentation.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Piotr Bugalski <bugalski.piotr@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add documentation for the addr-gpios. This extension to the physmap
binding allow creating flash devices that are paged using GPIOs.
Cc: devicetree@vger.kernel.org
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
- Remove an obsolete hack for PPC32 longtrail systems
- Make of_io_request_and_map() "name" arg optional
- Add vendor prefixes for bitmain, Asus, and Y Soft
- Remove 'interrupt-parent' from bindings as it is implicit
- New properties for wm8994 audio codec
- Add 'clocks' property support to SRAM binding
- Add binding for ASPEED coprocessor interrupt controller
- Various binding spelling and link fixes
-----BEGIN PGP SIGNATURE-----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=AV4E
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- Remove an obsolete hack for PPC32 longtrail systems
- Make of_io_request_and_map() "name" arg optional
- Add vendor prefixes for bitmain, Asus, and Y Soft
- Remove 'interrupt-parent' from bindings as it is implicit
- New properties for wm8994 audio codec
- Add 'clocks' property support to SRAM binding
- Add binding for ASPEED coprocessor interrupt controller
- Various binding spelling and link fixes
* tag 'devicetree-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
Documentation: remove dynamic-resolution-notes reference to non-existent file
dt-bindings: Add Y Soft Corporation vendor prefix
of/fdt: Remove PPC32 longtrail hack in memory scan
dt-bindings: remove 'interrupt-parent' from bindings
pinctrl: tegra: fix spelling in devicetree binding document
usb: dwc3: rockchip: Fix PHY documentation links.
dt-bindings: sound: wm8994: document wlf,csnaddr-pd property
dt-bindings: sound: wm8994: document wlf,spkmode-pu property
dt-bindings: sram: Add 'clocks' as an optional property
dt-bindings: Add vendor prefix for AsusTek Computer Inc.
dt-bindings: misc: ASPEED coprocessor interrupt controller
dt-bindings: gpio: pca953x: Document interrupts, update example
drivers/of: Make of_io_request_and_map() "name" argument optional
dt-bindings: Add bitmain vendor prefix
Documentation: devicetree: tilcdc: fix spelling mistake "suppors" -> "supports"
- Apply reset hacks only when reset is explicitly marked as broken in
the DT
Driver changes:
- Minor cleanup/fixes in the m25p80 driver
- Release flash_np in the nxp-spifi driver
- Add suspend/resume hooks to the atmel-quadspi driver
- Include gpio/consumer.h instead of gpio.h in the atmel-quadspi driver
- Use %pK instead of %p in the stm32-quadspi driver
- Improve timeout handling in the cadence-quadspi driver
- Use mtd_device_register() instead of mtd_device_parse_register() in
the intel-spi driver
-----BEGIN PGP SIGNATURE-----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=uNJl
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.19' of git://git.infradead.org/linux-mtd into mtd/next
Pull SPI NOR updates from Boris Brezillon:
"
Core changes:
- Apply reset hacks only when reset is explicitly marked as broken in
the DT
Driver changes:
- Minor cleanup/fixes in the m25p80 driver
- Release flash_np in the nxp-spifi driver
- Add suspend/resume hooks to the atmel-quadspi driver
- Include gpio/consumer.h instead of gpio.h in the atmel-quadspi driver
- Use %pK instead of %p in the stm32-quadspi driver
- Improve timeout handling in the cadence-quadspi driver
- Use mtd_device_register() instead of mtd_device_parse_register() in
the intel-spi driver
"
- Add the SPI-NAND framework.
- Create a helper to find the best ECC configuration.
- Create NAND controller operations.
- Allocate dynamically ONFI parameters structure.
- Add defines for ONFI version bits.
- Add manufacturer fixup for ONFI parameter page.
- Add an option to specify NAND chip as a boot device.
- Add Reed-Solomon error correction algorithm.
- Better name for the controller structure.
- Remove unused caller_is_module() definition.
- Make subop helpers return unsigned values.
- Expose _notsupp() helpers for raw page accessors.
- Add default values for dynamic timings.
- Kill the chip->scan_bbt() hook.
- Rename nand_default_bbt() into nand_create_bbt().
- Start to clean the nand_chip structure.
- Remove stale prototype from rawnand.h.
Raw NAND controllers drivers changes:
- Qcom: structuring cleanup.
- Denali: use core helper to find the best ECC configuration.
- Possible build of almost all drivers by adding a dependency on
COMPILE_TEST for almost all of them in Kconfig, implies various
fixes, Kconfig cleanup, GPIO headers inclusion cleanup, and even
changes in sparc64 and ia64 architectures.
- Clean the ->probe() functions error path of a lot of drivers.
- Migrate all drivers to use nand_scan() instead of
nand_scan_ident()/nand_scan_tail() pair.
- Use mtd_device_register() where applicable to simplify the code.
- Marvell:
* Handle on-die ECC.
* Better clocks handling.
* Remove bogus comment.
* Add suspend and resume support.
- Tegra: add NAND controller driver.
- Atmel:
* Add module param to avoid using dma.
* Drop Wenyou Yang from MAINTAINERS.
- Denali: optimize timings handling.
- FSMC: Stop using chip->read_buf().
- FSL:
* Switch to SPDX license tag identifiers.
* Fix qualifiers in MXC init functions.
Raw NAND chip drivers changes:
- Micron:
* Add fixup for ONFI revision.
* Update ecc_stats.corrected.
* Make ECC activation stateful.
* Avoid enabling/disabling ECC when it can't be disabled.
* Get the actual number of bitflips.
* Allow forced on-die ECC.
* Support 8/512 on-die ECC.
* Fix on-die ECC detection logic.
- Hynix:
* Fix decoding the OOB size on H27UCG8T2BTR.
* Use ->exec_op() in hynix_nand_reg_write_op().
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJbYYGVAAoJECVq6hhHvVaE0poIAJy+VpZl0jTPQ/oO8TQui9hE
IZbc8LwohCvegYYhiY1cNESyMYamDfoK6M93i/0zTJF2AJAxPl25ldT8N5Wr16DO
5Vfsdjv75V8l0JEY2SvWYmC6glOAYs0UEDdcFNJRMPqUnQz+VvBIafJOCQqzo4ZH
SDnLx3XzOxO4PAPnztWEg50WvaqMPt7ThcqoxThHMcQaLrNjgJUsV0mN+vNEv16Q
6gH6hl1C019k+Kj2Zu0vAifHw1K7gIYT4HvqKwstQ6HYUX2IzIzuEpRIcIze0S5z
XKzZ57USItb3l+Y3YwFBLjgP4N+VTT5X59LxdtCOXJ+YvzgxwtKElRvalNcryYI=
=zkEf
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.19' of git://git.infradead.org/linux-mtd into mtd/next
Pull NAND updates from Miquel Raynal:
"
NAND core changes:
- Add the SPI-NAND framework.
- Create a helper to find the best ECC configuration.
- Create NAND controller operations.
- Allocate dynamically ONFI parameters structure.
- Add defines for ONFI version bits.
- Add manufacturer fixup for ONFI parameter page.
- Add an option to specify NAND chip as a boot device.
- Add Reed-Solomon error correction algorithm.
- Better name for the controller structure.
- Remove unused caller_is_module() definition.
- Make subop helpers return unsigned values.
- Expose _notsupp() helpers for raw page accessors.
- Add default values for dynamic timings.
- Kill the chip->scan_bbt() hook.
- Rename nand_default_bbt() into nand_create_bbt().
- Start to clean the nand_chip structure.
- Remove stale prototype from rawnand.h.
Raw NAND controllers drivers changes:
- Qcom: structuring cleanup.
- Denali: use core helper to find the best ECC configuration.
- Possible build of almost all drivers by adding a dependency on
COMPILE_TEST for almost all of them in Kconfig, implies various
fixes, Kconfig cleanup, GPIO headers inclusion cleanup, and even
changes in sparc64 and ia64 architectures.
- Clean the ->probe() functions error path of a lot of drivers.
- Migrate all drivers to use nand_scan() instead of
nand_scan_ident()/nand_scan_tail() pair.
- Use mtd_device_register() where applicable to simplify the code.
- Marvell:
* Handle on-die ECC.
* Better clocks handling.
* Remove bogus comment.
* Add suspend and resume support.
- Tegra: add NAND controller driver.
- Atmel:
* Add module param to avoid using dma.
* Drop Wenyou Yang from MAINTAINERS.
- Denali: optimize timings handling.
- FSMC: Stop using chip->read_buf().
- FSL:
* Switch to SPDX license tag identifiers.
* Fix qualifiers in MXC init functions.
Raw NAND chip drivers changes:
- Micron:
* Add fixup for ONFI revision.
* Update ecc_stats.corrected.
* Make ECC activation stateful.
* Avoid enabling/disabling ECC when it can't be disabled.
* Get the actual number of bitflips.
* Allow forced on-die ECC.
* Support 8/512 on-die ECC.
* Fix on-die ECC detection logic.
- Hynix:
* Fix decoding the OOB size on H27UCG8T2BTR.
* Use ->exec_op() in hynix_nand_reg_write_op().
"
Commit 59b356ffd0 ("mtd: m25p80: restore the status of SPI flash when
exiting") is the latest from a long history of attempts to add reboot
handling to handle stateful addressing modes on SPI flash. Some prior
mostly-related discussions:
http://lists.infradead.org/pipermail/linux-mtd/2013-March/046343.html
[PATCH 1/3] mtd: m25p80: utilize dedicated 4-byte addressing commands
http://lists.infradead.org/pipermail/barebox/2014-September/020682.html
[RFC] MTD m25p80 3-byte addressing and boot problem
http://lists.infradead.org/pipermail/linux-mtd/2015-February/057683.html
[PATCH 2/2] m25p80: if supported put chip to deep power down if not used
Previously, attempts to add reboot-time software reset handling were
rejected, but the latest attempt was not.
Quick summary of the problem:
Some systems (e.g., boot ROM or bootloader) assume that they can read
initial boot code from their SPI flash using 3-byte addressing. If the
flash is left in 4-byte mode after reset, these systems won't boot. The
above patch provided a shutdown/remove hook to attempt to reset the
addressing mode before we reboot. Notably, this patch misses out on
huge classes of unexpected reboots (e.g., crashes, watchdog resets).
Unfortunately, it is essentially impossible to solve this problem 100%:
if your system doesn't know how to reset the SPI flash to power-on
defaults at initialization time, no amount of software can really rescue
you -- there will always be a chance of some unexpected reset that
leaves your flash in an addressing mode that your boot sequence didn't
expect.
While it is not directly harmful to perform hacks like the
aforementioned commit on all 4-byte addressing flash, a
properly-designed system should not need the hack -- and in fact,
providing this hack may mask the fact that a given system is indeed
broken. So this patch attempts to apply this unsound hack more narrowly,
providing a strong suggestion to developers and system designers that
this is truly a hack. With luck, system designers can catch their errors
early on in their development cycle, rather than applying this hack long
term. But apparently enough systems are out in the wild that we still
have to provide this hack.
Document a new device tree property to denote systems that do not have a
proper hardware (or software) reset mechanism, and apply the hack (with
a loud warning) only in this case.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
'interrupt-parent' is often documented as part of define bindings, but
it is really outside the scope of a device binding. It's never required
in a given node as it is often inherited from a parent node. Or it can
be implicit if a parent node is an 'interrupt-controller' node. So
remove it from all the binding files.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Documentation was already saying that fixed and dynamic partitioning can
be mixed but was missing a clear description and examples. This commit
adds a proper documentation of how descriptions can be nested and how
layouts can be mixed.
This addition is important for partitions that contain subpartitions.
In such cases partitions have to be properly described in order to let
system handle them correctly.
Depending on situation, nesting descriptions may provide more accurate
logic/structure and/or allow mixing partitioning types (various
"compatible" values).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Commit 30f9f2fb7b ("mtd: denali: add a DT driver") supported the
clock enablement, but did not document it in the DT binding.
In addition to the existing clock, this commit adds more clocks based
on the IP specification.
According to the Denali User's Guide, this IP needs three clocks:
- clk: controller core clock
- clk_x: bus interface clock
- ecc_clk: clock at which ECC circuitry is run
The driver should accept the current single clock for the backward
compatibility, but the DT binding should represent the real hardware,
and future platforms must follow this.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
1. If nand-ecc-strength specified in DT, then controller will use
this ECC strength otherwise ECC strength will be calculated
according to chip requirement and available OOB size.
2. QCOM NAND controller supports only one step size (512 bytes) but
nand-ecc-step-size is required property in DT. This DT property
can be removed and ecc step size can be assigned in driver with
512 bytes value.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Broadcom based home router devices use TRX firmware format. It's a
container that can hold few partitions. If operating system is expected
to access them it has to understand that format and parse flash data
accordingly.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This adds the devicetree binding for the Tegra 2 NAND flash
controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Allow to define a NAND chip as a boot device. This can be helpful
for the selection of the ECC algorithm and strength in case the boot
ROM supports only a subset of controller provided options.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add Reed-Solomon (RS) to the enumeration of ECC algorithms.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Core changes:
- Add a sysfs attribute to expose available OOB size
Driver changes:
- Remove HAS_DMA dependency on various drivers
- Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
- Replace msleep by usleep_range() in the dataflash driver
- Avoid VLA usage in nftl layers
- Remove useless .owner assignment in pismo
- Fix various issues in the CFI driver
- Improve TRX partition handling expose a DT compat for this part
parser
- Clarify OFFSET_CONTINUOUS meaning
NAND changes:
Core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
* Cleanup/simplification of a few aspects in the driver
* Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
* Use of_device_get_match_data() instead of of_match_device()
* Add an entry in MAINTAINERS for this driver
* Fix nand-ecc-step-size and nand-ecc-strength description in the DT
bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
SPI NOR changes:
Core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
* Mark the driver as "dangerous" in Kconfig
* Fix atomic sequence handling
* Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
* fix a typo in a function name
* add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line
-----BEGIN PGP SIGNATURE-----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=cHjU
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"Core changes:
- Add a sysfs attribute to expose available OOB size
Driver changes:
- Remove HAS_DMA dependency on various drivers
- Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
- Replace msleep by usleep_range() in the dataflash driver
- Avoid VLA usage in nftl layers
- Remove useless .owner assignment in pismo
- Fix various issues in the CFI driver
- Improve TRX partition handling expose a DT compat for this part
parser
- Clarify OFFSET_CONTINUOUS meaning
NAND core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
+ Cleanup/simplification of a few aspects in the driver
+ Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
+ Use of_device_get_match_data() instead of of_match_device()
+ Add an entry in MAINTAINERS for this driver
+ Fix nand-ecc-step-size and nand-ecc-strength description in the
DT bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
SPI NOR core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
+ Mark the driver as "dangerous" in Kconfig
+ Fix atomic sequence handling
+ Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
+ fix a typo in a function name
+ add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line"
* tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd: (66 commits)
mtd: nand: Pass mode information to nand_page_io_req
mtd: cfi_cmdset_0002: Change erase one block to enable XIP once
mtd: cfi_cmdset_0002: Change erase functions to check chip good only
mtd: cfi_cmdset_0002: Change erase functions to retry for error
mtd: cfi_cmdset_0002: Change definition naming to retry write operation
mtd: cfi_cmdset_0002: Change write buffer to check correct value
mtd: cmdlinepart: Update comment for introduction of OFFSET_CONTINUOUS
mtd: bcm47xxpart: add of_match_table with a new DT binding
dt-bindings: mtd: document Broadcom's BCM47xx partitions
mtd: spi-nor: Add support for EN25QH32
mtd: spi-nor: Add support for is25wp series chips
mtd: spi-nor: Add Winbond w25q32jv support
mtd: spi-nor: fsl-quadspi: add support for ls2080a/ls1080a
mtd: spi-nor: stm32-quadspi: explicitly request exclusive reset control
mtd: spi-nor: intel: provide a range for poll_timout
mtd: spi-nor: fsl-quadspi: fix api naming typo _init_ahb_read
mtd: spi-nor: intel-spi: Explicitly mark the driver as dangerous in Kconfig
mtd: spi-nor: intel-spi: Fix atomic sequence handling
mtd: rawnand: Do not check FAIL bit when executing a SET_FEATURES op
mtd: rawnand: use bit-wise majority to recover the ONFI param page
...
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
* Cleanup/simplification of a few aspects in the driver
* Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
* Use of_device_get_match_data() instead of of_match_device()
* Add an entry in MAINTAINERS for this driver
* Fix nand-ecc-step-size and nand-ecc-strength description in the DT
bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
-----BEGIN PGP SIGNATURE-----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=MzWF
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.18' of git://git.infradead.org/linux-mtd into mtd/next
Core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
* Cleanup/simplification of a few aspects in the driver
* Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
* Use of_device_get_match_data() instead of of_match_device()
* Add an entry in MAINTAINERS for this driver
* Fix nand-ecc-step-size and nand-ecc-strength description in the DT
bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
Broadcom based home router devices use partitions which have to be
discovered in a specific way. They are not fixed and there is not any
standard partition table. This commit adds and describes a new custom
binding for such devices.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Update ecc step size, ecc strength, and parity bits supported on
each MTK NAND controller.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
None of the existing platforms connect the R/B pin to a GPIO (they all
use one of the dedicated R/B pin).
Anyway, if we ever get short of native R/B pins, it's probably better
to fallback to STATUS reg polling than trying to poll a GPIO.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Document newly supported device tree properties nand-ecc-strength/
nand-ecc-step-size to specify ECC strength/size.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Bindings are supposed to be organized by device class/function. Move a
couple of powerpc 4xx bindings to the correct binding directory.
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
* Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Driver changes:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
-----BEGIN PGP SIGNATURE-----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=uvio
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.17' of git://git.infradead.org/linux-mtd into mtd/next
Core changes:
* Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Driver changes:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
to the same QSPI controller
* Remove an unneeded driver.bus assigned in the fsl-qspi driver
-----BEGIN PGP SIGNATURE-----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=Wrxi
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.17' of git://git.infradead.org/linux-mtd into mtd/next
* Make fsl-quaspi assign different names to MTD devices connected
to the same QSPI controller
* Remove an unneeded driver.bus assigned in the fsl-qspi driver
Improve the bindings example by adding an example of how to represent
two SPI NOR devices.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This mode is not used by any existing setup and should not be used
because it overwrites the BBMs. Let's just remove it before someone
starts using it.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
On Armada 7K/8K we need to explicitly enable the register clock. This
clock is optional because not all the SoCs using this IP need it but at
least for Armada 7K/8K it is actually mandatory.
The binding documentation is updated accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Provide a way to specify the endianness to use when accessing a
memory-mapped flash.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The deprecated pxa3xx_nand.c driver does not exist anymore, it has been
replaced by marvell_nand.c which has its own up-to-date documentation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
- Convert to use memblock_virt_alloc in DT code which supports bootmem
arches. With this we can remove the arch specific
early_init_dt_alloc_memory_arch() functions.
- Enable running the DT unittests on UML
- Use SPDX license tags on DT files
- Fix early FDT kconfig ifdef logic
- Clean-up unittest Makefile
- Fix function comment for of_irq_parse_raw
- Add missing documentation for linux,initrd-{start,end} properties
- Clean-up of binding examples using uppercase hex
- Add trivial devices W83773G and Infineon TLV493D-A1B6
- Add missing STM32 SoC bindings
- Various small binding doc fixes
-----BEGIN PGP SIGNATURE-----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=v6gj
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- Convert to use memblock_virt_alloc in DT code which supports
bootmem arches. With this we can remove the arch specific
early_init_dt_alloc_memory_arch() functions.
- Enable running the DT unittests on UML
- Use SPDX license tags on DT files
- Fix early FDT kconfig ifdef logic
- Clean-up unittest Makefile
- Fix function comment for of_irq_parse_raw
- Add missing documentation for linux,initrd-{start,end} properties
- Clean-up of binding examples using uppercase hex
- Add trivial devices W83773G and Infineon TLV493D-A1B6
- Add missing STM32 SoC bindings
- Various small binding doc fixes
* tag 'devicetree-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (23 commits)
xtensa: remove arch specific early DT functions
x86: remove arch specific early_init_dt_alloc_memory_arch
nios2: remove arch specific early_init_dt_alloc_memory_arch
mips: remove arch specific early_init_dt_alloc_memory_arch
metag: remove arch specific early DT functions
cris: remove arch specific early DT functions
libfdt: remove unnecessary include directive from <linux/libfdt.h>
of: unittest: refactor Makefile
of/fdt: use memblock_virt_alloc for early alloc
of: Use SPDX license tag for DT files
of/fdt: Fix #ifdef dependency of early flattree declarations
dt-bindings: h8300 clocksource: correct spelling of pulse
dt-bindings: imx6q-pcie: Add required property for i.MX6SX
mmc: Don't reference Linux-specific OF_GPIO_ACTIVE_LOW flag in DT binding
dt-bindings: Use lower case hex in unit-addresses
dt-bindings: display: panel: Fix compatible string for Toshiba LT089AC29000
dt-bindings: Add Infineon TLV493D-A1B6
dt-bindings: mailbox: ti,message-manager: Fix interrupt name error
dt-bindings: chosen: Document linux,initrd-{start,end}
dt-bindings: arm: document supported STM32 SoC family
...
Core changes:
* Rework core functions to avoid duplicating generic checks in
NAND/OneNAND sub-layers
* Update the MAINTAINERS entry to reflect the fact that MTD
maintainers now use a single git tree
Driver changes:
* CFI: use macros instead of inline functions to limit stack
usage and make KASAN happy
NAND changes:
Core changes:
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
* Introduce the ->exec_op() infrastructure
* Rework NAND buffers handling
* Fix ECC requirements for K9F4G08U0D
* Fix nand_do_read_oob() to return the number of bitflips
* Mark K9F1G08U0E as not supporting subpage writes
Driver changes:
* MTK: Rework the driver to support new IP versions
* OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
DT support
* Marvell: Add a new driver to replace the pxa3xx one
SPI NOR changes:
Core changes:
* Add support to new ISSI and Cypress/Spansion memory parts.
* Fix support of Micron memories by checking error bits in the FSR.
* Fix update of block-protection bits by reading back the SR.
* Restore the internal state of the SPI flash memory when removing the
device.
Driver changes:
* Maintenance for Freescale, Intel and Metiatek drivers.
* Add support of the direct access mode for the Cadence QSPI controller.
-----BEGIN PGP SIGNATURE-----
iQJABAABCAAqBQJabumAIxxib3Jpcy5icmV6aWxsb25AZnJlZS1lbGVjdHJvbnMu
Y29tAAoJEGXtNgF+CLcA0eAP/1s4u/Vs0RaDL2Jog0z+3fdx9HKYTK01hiQoe5Vf
0ouGH0lR9usAmmJlXxxNpBHFvJxsofJoCNaciHAiydCMBpX6oAQMYMMcPs4Qo7C/
vydLBDBmKZNyQ9dv6FbjP+3Y/5drIGF+VfxXZwhGA3lwP5CSVbB9ndI8+A5bScIV
m2RMOA/lorbNHQahEkt7FHd92yQxBXlbhHBf5Foy2dGhO3rpTWzL/d1KPAkcfeli
ehjfazkbuwFxGlYBFsrWxsnm0zqrqIWtdTE5/0i8iC1FfbxL5KjRnAFg8AsXIepn
C2rCAxM/890mIFypT/8xhu+1u8+Bmb1r/pA9G+f3zpkiAHcUGC3eMO3IhX/jkcAd
jCD/zeaSW8uHrBoJA6mGhO1tkBA97w15XCQC38UZkRMaJsY8Rv50ST4afA4in7mi
bdRnpOOBYsBv9LvLm+FzQ0EgRQl642mFY8rae+gAjkF/zt8zGHSt6UNgtwMRxqZJ
ns/TyhNm7roYV3cPpAgOWK//9XAGII9YZ6x9XmPNZLq62yf+zqJnfeuy7bXATRfG
GGYk6wd+VdN+Ax2mqVKEJMCArjz0kLAHOtpIwv2/RxB1dlNMdugaDPUcqFteZbXh
wlgORLXLqZ8jfy+ITFB5HMDs/NMyuRr815jdPGZafHIx8xOBQD32Izv7cpYctfWU
f2NU
=Mxo2
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"MTD core changes:
- Rework core functions to avoid duplicating generic checks in
NAND/OneNAND sub-layers
- Update the MAINTAINERS entry to reflect the fact that MTD
maintainers now use a single git tree
MTD driver changes:
- CFI: use macros instead of inline functions to limit stack usage
and make KASAN happy
NAND core changes:
- Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
- Introduce the ->exec_op() infrastructure
- Rework NAND buffers handling
- Fix ECC requirements for K9F4G08U0D
- Fix nand_do_read_oob() to return the number of bitflips
- Mark K9F1G08U0E as not supporting subpage writes
NAND driver changes:
- MTK: Rework the driver to support new IP versions
- OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and
fix DT support
- Marvell: Add a new driver to replace the pxa3xx one
SPI NOR core changes:
- Add support to new ISSI and Cypress/Spansion memory parts.
- Fix support of Micron memories by checking error bits in the FSR.
- Fix update of block-protection bits by reading back the SR.
- Restore the internal state of the SPI flash memory when removing
the device.
SPI NOR driver changes:
- Maintenance for Freescale, Intel and Metiatek drivers.
- Add support of the direct access mode for the Cadence QSPI
controller"
* tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd: (93 commits)
mtd: nand: sunxi: Fix ECC strength choice
mtd: nand: gpmi: Fix subpage reads
mtd: nand: Fix build issues due to an anonymous union
mtd: nand: marvell: Fix missing memory allocation modifier
mtd: nand: marvell: remove redundant variable 'oob_len'
mtd: nand: marvell: fix spelling mistake: "suceed"-> "succeed"
mtd: onenand: omap2: Remove redundant dev_err call in omap2_onenand_probe()
mtd: Remove duplicate checks on mtd_oob_ops parameter
mtd: Fallback to ->_read/write_oob() when ->_read/write() is missing
mtd: mtdpart: Make ECC stat handling consistent
mtd: onenand: omap2: print resource using %pR format string
mtd: mtk-nor: modify functions' name more generally
mtd: onenand: samsung: remove incorrect __iomem annotation
MAINTAINERS: Add entry for Marvell NAND controller driver
ARM: OMAP2+: Remove gpmc-onenand
mtd: onenand: omap2: Configure driver from DT
mtd: onenand: omap2: Decouple DMA enabling from INT pin availability
mtd: onenand: omap2: Do not make delay for GPIO OMAP3 specific
mtd: onenand: omap2: Convert to use dmaengine for memcpy
mtd: onenand: omap2: Unify OMAP2 and OMAP3 DMA implementation
...
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
* Introduce the ->exec_op() infrastructure
* Rework NAND buffers handling
* Fix ECC requirements for K9F4G08U0D
* Fix nand_do_read_oob() to return the number of bitflips
* Mark K9F1G08U0E as not supporting subpage writes
Driver changes:
* MTK: Rework the driver to support new IP versions
* OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
DT support
* Marvell: Add a new driver to replace the pxa3xx one
-----BEGIN PGP SIGNATURE-----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=TXIU
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.16' of git://git.infradead.org/linux-mtd into mtd/next
Pull NAND changes from Boris Brezillon:
"
Core changes:
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
* Introduce the ->exec_op() infrastructure
* Rework NAND buffers handling
* Fix ECC requirements for K9F4G08U0D
* Fix nand_do_read_oob() to return the number of bitflips
* Mark K9F1G08U0E as not supporting subpage writes
Driver changes:
* MTK: Rework the driver to support new IP versions
* OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
DT support
* Marvell: Add a new driver to replace the pxa3xx one
"
Compatible property is required for OMAP2+ mtd driver. Also
add INT pin gpio description and delete unused dma-channel
property.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Document the legacy and the new bindings for Marvell NAND controller.
The pxa3xx_nand.c driver does only support legacy bindings, which are
incomplete and inaccurate. A rework of this controller (called
marvell_nand.c) does support both.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There are already an atmel,rb and an allwinner,rb properties, let's not
make other ones and instead use a generic term: nand-rb to define NAND
chips Ready/Busy lines.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
DT unit addresses should be lower case hex. Fix all the
binding examples.
Converted with the following command from Krzysztof Kozlowski:
sed -e 's/@\([a-fA-F0-9_-]*\) {/@\L\1 {/' -i $(find Documentation/devicetree/bindings -name '*.txt')
Signed-off-by: Rob Herring <robh@kernel.org>
