Document RZ/G2UL RPC-IF bindings. RZ/G2UL RPC-IF is identical to one found
on the RZ/G2L SoC. No driver changes are required as generic compatible
string "renesas,rzg2l-rpc-if" will be used as a fallback.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220501082508.25511-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
From Tegra186 onwards, memory controller support multiple channels.
"reg" items are updated with address and size of these channels.
Tegra186 has overall 5 memory controller channels. Tegra194 and Tegra234
have overall 17 memory controller channels each.
There is one "reg" entry for memory controller stream-ID registers. So
update the "reg" property's "minItems" and "maxItems" accordingly in the
Tegra186 devicetree documentation.
Also update validation for "reg-names" added for these corresponding
"reg" items. ABI change due to new bindings is intended but backward
compatibility is preserved in driver.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ashish Mhetre <amhetre@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
DDR DVFS tuning has found that several power-saving features don't have
good tradeoffs at higher frequencies -- at higher frequencies, we'll see
glitches or other errors. Provide tuning controls so these can be
disabled at higher OPPs, and left active only at the lower ones.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
It's inefficient to use the same number of cycles for all OPPs, since
lower frequencies make for longer idle times. Let's specify the idle
time instead, so software can pick the optimal number of cycles on its
own.
NB: these bindings aren't used anywhere yet.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The driver and all downstream device trees [1] are using Hz units, but
the document claims MHz. DRAM frequency for these systems can't possibly
exceed 2^32-1 Hz, so the choice of unit doesn't really matter than much.
Rather than add unnecessary risk in getting the units wrong, let's just
go with the unofficial convention and make the docs match reality.
A sub-1MHz frequency is extremely unlikely, so include a minimum in the
schema, to help catch anybody who might have believed this was MHz.
[1] And notably, also those trying to upstream them:
https://lore.kernel.org/lkml/20210308233858.24741-3-daniel.lezcano@linaro.org/
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
These DRAM configuration properties are all handled in ARM Trusted
Firmware (and have been since the early days of this SoC), and there are
no in-tree users of the DMC binding yet. It's better to just defer to
firmware instead of maintaining this large list of properties.
There's also some confusion about units: many of these are specified in
MHz, but the downstream users and driver code are treating them as Hz, I
believe. Rather than straighten all that out, I just drop them.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
I want to add, deprecate, and bugfix some properties, as well as add the
first users. This is easier with a proper schema.
The transformation is mostly straightforward, plus a few notable tweaks:
* Renamed rockchip,dram_speed_bin to rockchip,ddr3_speed_bin. The
driver code and the example matched, but the description was
different. I went with the implementation. Note that this property is
also slated for deprecation/deletion in the subsequent patches.
* Drop upthreshold and downdifferential properties from the example.
These were undocumented (so, wouldn't pass validation), but were
representing software properties (governor tweaks). I drop them from
the driver in subsequent patches.
* Rename clock from pclk_ddr_mon to dmc_clk. The driver, DT example,
and all downstream users matched -- the binding definition was the
exception. Anyway, "dmc_clk" is a more appropriately generic name.
* Choose a better filename and location (this is a memory controller).
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Document support for the SPI Multi I/O Bus Controller (RPC-IF) in the
R-Car H3, M3-W, M3-W+, M3-N, and E3 SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/3784b6cb76a008fb56d6cb4ba228d78c77e710fa.1648546583.git.geert+renesas@glider.be
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Since
8a4ab218ef ("powerpc/85xx: Change deprecated binding for 85xx-based boards")
those bindings are not used anymore.
A comment in drivers/edac/mpc85xx_edac.c say they are to be removed
with kernel 2.6.30.
Remove them now.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Scott Wood <oss@buserror.net>
Link: https://lore.kernel.org/r/82a8bc4450a4daee50ee5fada75621fecb3703ff.1648721299.git.christophe.leroy@csgroup.eu
For the snps,ddrc-3.80a compatible, the interrupts property is also
required, also order the compatibles by name (s goes before x).
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Fixes: a9e6b3819b ("dt-bindings: memory: Add entry for version 3.80a")
Link: https://lore.kernel.org/r/20220321075131.17811-2-sherry.sun@nxp.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Krzysztof Kozlowski's @canonical.com email stopped working, so switch to
generic @kernel.org account for all Devicetree bindings.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220330074016.12896-2-krzysztof.kozlowski@linaro.org
* 'remove-h8300' of git://git.infradead.org/users/hch/misc:
remove the h8300 architecture
This is clearly the least actively maintained architecture we have at
the moment, and probably the least useful. It is now the only one that
does not support MMUs at all, and most of the boards only support 4MB
of RAM, out of which the defconfig kernel needs more than half just
for .text/.data.
Guenter Roeck did the original patch to remove the architecture in 2013
after it had already been obsolete for a while, and Yoshinori Sato brought
it back in a much more modern form in 2015. Looking at the git history
since the reinstantiation, it's clear that almost all commits in the tree
are build fixes or cross-architecture cleanups:
$ git log --no-merges --format=%an v4.5.. arch/h8300/ | sort | uniq
-c | sort -rn | head -n 12
25 Masahiro Yamada
18 Christoph Hellwig
14 Mike Rapoport
9 Arnd Bergmann
8 Mark Rutland
7 Peter Zijlstra
6 Kees Cook
6 Ingo Molnar
6 Al Viro
5 Randy Dunlap
4 Yury Norov
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Add Krzysztof Kozlowski as co-maintainer for DT bindings providing
much needed help.
- DT schema validation now takes DTB files as input rather than
intermediate YAML files. This decouples the validation from the source
level syntax information. There's a bunch of schema fixes as a result
of switching to DTB based validation which exposed some errors
and incomplete schemas and examples.
- Kbuild improvements to explicitly warn users running 'make
dt_binding_check' on missing yamllint
- Expand DT_SCHEMA_FILES kbuild variable to take just a partial filename
or path instead of the full path to 1 file.
- Convert various bindings to schema format: mscc,vsc7514-switch,
multiple GNSS bindings, ahci-platform, i2c-at91, multiple UFS
bindings, cortina,gemini-sata-bridge, cortina,gemini-ethernet, Atmel
SHA, Atmel TDES, Atmel AES, armv7m-systick, Samsung Exynos display
subsystem, nuvoton,npcm7xx-timer, samsung,s3c2410-i2c, zynqmp_dma,
msm/mdp4, rda,8810pl-uart
- New schemas for u-boot environment variable partition, TI clksel
- New compatible strings for Renesas RZ/V2L SoC
- Vendor prefixes for Xen, HPE, deprecated Synopsys, deprecated HiSilicon
- Add/fix schemas for QEMU Arm 'virt' machine
- Drop unused of_alias_get_alias_list() function
- Add a script to check DT unittest EXPECT message output. Pass messages
also now print by default at PR_INFO level to help test automation.
-----BEGIN PGP SIGNATURE-----
iQJEBAABCgAuFiEEktVUI4SxYhzZyEuo+vtdtY28YcMFAmI8s64QHHJvYmhAa2Vy
bmVsLm9yZwAKCRD6+121jbxhwx3tD/4j56NE+aLkL636+I8tGFm3r+r6uLLT4SWh
zDuiX3MP9OKfhJw43TjjURLwX5adBnG3nn505IXcAeiMRgEiciOpSa12w0mXyjMX
QgVOcoaI3H2GBMEddJRo1PLTM/K5sYzZxAKLB827xoOk4mGNA0ZBAHvlB3W+yLE5
CE5yTaFoL4EMXuhWMtMrMlG1PQrbO3FpQ2DHBKrpxHPJmnHLk3c0YtMSTHGQnWbN
AxT3S6RSsOLwLzZAXi2AlswqY82n5KtUf/RBrYi8rdr/xnIsCfMeXxafkP2Hyxkq
L9RfKVn05c0LRtO1Eh8kYr+lmYmcWz/SIdJZXzpviIgE9MJapCAk0blBZ4S/FH0B
EVGB1JkwCZFck6DBmkNJxAwR0iQOGWkJIkn6iBPNF0dHp58eE6adaXjhFH3uBEHk
dXFaxPlvZ3P/Q2I/vmQ//m5tZMyjeCY2BlVYpkUJMOFfN26MIGHUmUlLnovLDqu4
lYgZG4V244uYzALLbURpbp+5dlPH/PL2gxvJJNqTS+/hXktQx1XnML4wD+xfJ4nT
OY5DD7Z+KGBrdsMtxkFtIFvKD63E2gtAR5RZO0J/txlzhW7Wg6fJbhJZeRFhZKmN
GAfud2s6rliyygByBL4ea50DSLLQpc/9HZtFmZ3NTILM6NbUR74sHt+1EZ1hee+M
LaNsSscHuQ==
=g1li
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Add Krzysztof Kozlowski as co-maintainer for DT bindings providing
much needed help.
- DT schema validation now takes DTB files as input rather than
intermediate YAML files. This decouples the validation from the
source level syntax information. There's a bunch of schema fixes as a
result of switching to DTB based validation which exposed some errors
and incomplete schemas and examples.
- Kbuild improvements to explicitly warn users running 'make
dt_binding_check' on missing yamllint
- Expand DT_SCHEMA_FILES kbuild variable to take just a partial
filename or path instead of the full path to 1 file.
- Convert various bindings to schema format: mscc,vsc7514-switch,
multiple GNSS bindings, ahci-platform, i2c-at91, multiple UFS
bindings, cortina,gemini-sata-bridge, cortina,gemini-ethernet, Atmel
SHA, Atmel TDES, Atmel AES, armv7m-systick, Samsung Exynos display
subsystem, nuvoton,npcm7xx-timer, samsung,s3c2410-i2c, zynqmp_dma,
msm/mdp4, rda,8810pl-uart
- New schemas for u-boot environment variable partition, TI clksel
- New compatible strings for Renesas RZ/V2L SoC
- Vendor prefixes for Xen, HPE, deprecated Synopsys, deprecated
HiSilicon
- Add/fix schemas for QEMU Arm 'virt' machine
- Drop unused of_alias_get_alias_list() function
- Add a script to check DT unittest EXPECT message output. Pass
messages also now print by default at PR_INFO level to help test
automation.
* tag 'devicetree-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (96 commits)
dt-bindings: kbuild: Make DT_SCHEMA_LINT a recursive variable
dt-bindings: nvmem: add U-Boot environment variables binding
dt-bindings: ufs: qcom: Add SM6350 compatible string
dt-bindings: dmaengine: sifive,fu540-c000: include generic schema
dt-bindings: gpio: pca95xx: drop useless consumer example
Revert "of: base: Introduce of_alias_get_alias_list() to check alias IDs"
dt-bindings: virtio,mmio: Allow setting devices 'dma-coherent'
dt-bindings: gnss: Add two more chips
dt-bindings: gnss: Rewrite sirfstar binding in YAML
dt-bindings: gnss: Modify u-blox to use common bindings
dt-bindings: gnss: Rewrite common bindings in YAML
dt-bindings: ata: ahci-platform: Add rk3568-dwc-ahci compatible
dt-bindings: ata: ahci-platform: Add power-domains property
dt-bindings: ata: ahci-platform: Convert DT bindings to yaml
dt-bindings: kbuild: Use DTB files for validation
dt-bindings: kbuild: Pass DT_SCHEMA_FILES to dt-validate
dt-bindings: Add QEMU virt machine compatible
dt-bindings: arm: Convert QEMU fw-cfg to DT schema
dt-bindings: i2c: at91: Add SAMA7G5 compatible strings list
dt-bindings: i2c: convert i2c-at91 to json-schema
...
Document RZ/V2L RPC-IF bindings. RZ/V2L RPC-IF is identical to one found
on the RZ/G2L SoC. No driver changes are required as generic compatible
string "renesas,rzg2l-rpc-if" will be used as a fallback.
While at it, drop the comment "# RZ/G2L family" for "renesas,rzg2l-rpc-if"
compatible string as this will avoid changing the line for every new SoC
addition.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220301123527.15950-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
1. Several updates in the MTK SMI bindings.
2. Add support for MT8186 MTK SMI and improvements in support for MT8195.
-----BEGIN PGP SIGNATURE-----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=V7gd
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=Bquy
-----END PGP SIGNATURE-----
Merge tag 'memory-controller-drv-mediatek-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/drivers
Memory controller drivers for v5.18 - Mediatek SoC
1. Several updates in the MTK SMI bindings.
2. Add support for MT8186 MTK SMI and improvements in support for MT8195.
* tag 'memory-controller-drv-mediatek-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
memory: mtk-smi: Enable sleep ctrl safety function for MT8195
memory: mtk-smi: mt8186: Add smi support
memory: mtk-smi: Add sleep ctrl function
memory: mtk-smi: handle positive return value for clk_bulk_prepare_enable
dt-bindings: memory: mediatek: Add mt8186 support
dt-bindings: memory: mtk-smi: Correct minItems to 2 for the gals clocks
dt-bindings: memory: mtk-smi: No need mediatek,larb-id for mt8167
dt-bindings: memory: mtk-smi: Rename clock to clocks
Link: https://lore.kernel.org/r/20220228164313.52931-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 3539a2c6c6 ("dt-bindings: memory: lpddr2: Add revision-id
properties") added the properties `revision-id1` and `revision-id2` to
the "jedec,lpddr2" binding. The "jedec,lpddr3" binding already had a
single array property `revision-id` for the same purpose. For
consistency between related memory types, this patch deprecates the
LPDDR2 properties and instead adds a property in the same style as for
LPDDR3 to that binding.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220224003421.3440124-2-jwerner@chromium.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The timings node maximum frequency was passed as an unit address, which
is actually a workaround. Such workaround and unit address are not
needed at all, because the device memory node (parent) can contain
multiple timing nodes without unit addresses but with suffix used for
nodenames, e.g. timings-1.
LPDDR2 bindings already use such version, so unify the LPDDR3 with them.
Suggested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220206135807.211767-7-krzysztof.kozlowski@canonical.com
The memory manufacturer should be described in vendor part of
compatible, so there is no need to duplicate it in a separate property.
Similarly is done in LPDDR2 bindings.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220206135807.211767-6-krzysztof.kozlowski@canonical.com
According to JEDEC Standard No. 209-3 (table 3.4.1 "Mode Register
Assignment and Definition in LPDDR3 SDRAM"), the LPDDR3 supports only
16- and 32-bit IO width. Drop the unsupported others.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220206135807.211767-5-krzysztof.kozlowski@canonical.com
The 'phandle-array' type is a bit ambiguous. It can be either just an
array of phandles or an array of phandles plus args. Many schemas for
phandle-array properties aren't clear in the schema which case applies
though the description usually describes it.
The array of phandles case boils down to needing:
items:
maxItems: 1
The phandle plus args cases should typically take this form:
items:
- items:
- description: A phandle
- description: 1st arg cell
- description: 2nd arg cell
With this change, some examples need updating so that the bracketing of
property values matches the schema.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220119015038.2433585-1-robh@kernel.org
Convert the txt binding to yaml format and add description. Drop the
"simple-bus" compatible string from the example and not allowed by the
binding any more. This will help to enforce the correct probe order
between parent device and child devices, but will require the ifc driver
to probe the child devices to work properly.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211116211846.16335-2-leoyang.li@nxp.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Add mt8186 smi support in the bindings.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220113111057.29918-5-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Mute the warning from "make dtbs_check":
larb@14017000: clock-names: ['apb', 'smi'] is too short
arch/arm64/boot/dts/mediatek/mt8183-evb.dt.yaml
arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-burnet.dt.yaml
...
larb@16010000: clock-names: ['apb', 'smi'] is too short
arch/arm64/boot/dts/mediatek/mt8183-evb.dt.yaml
arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-burnet.dt.yaml
larb@17010000: clock-names: ['apb', 'smi'] is too short
arch/arm64/boot/dts/mediatek/mt8183-evb.dt.yaml
arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-burnet.dt.yaml
If a platform's larb supports gals, there will be some larbs have one
more "gals" clock while the others still only need "apb"/"smi" clocks,
then the minItems for clocks and clock-names are 2.
Fixes: 27bb0e4285 ("dt-bindings: memory: mediatek: Convert SMI to DT schema")
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220113111057.29918-4-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Mute the warning from "make dtbs_check":
larb@14016000: 'mediatek,larb-id' is a required property
arch/arm64/boot/dts/mediatek/mt8167-pumpkin.dt.yaml
larb@15001000: 'mediatek,larb-id' is a required property
arch/arm64/boot/dts/mediatek/mt8167-pumpkin.dt.yaml
larb@16010000: 'mediatek,larb-id' is a required property
arch/arm64/boot/dts/mediatek/mt8167-pumpkin.dt.yaml
As the description of mediatek,larb-id, the property is only
required when the larbid is not consecutive from its IOMMU point of view.
Also, from the description of mediatek,larbs in
Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml, all the larbs
must sort by the larb index.
In mt8167, there is only one IOMMU HW and three larbs. The drivers already
know its larb index from the mediatek,larbs property of IOMMU, thus no
need this property.
Fixes: 27bb0e4285 ("dt-bindings: memory: mediatek: Convert SMI to DT schema")
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220113111057.29918-3-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The property "clock" should be rename to "clocks", and delete the "items",
the minItems/maxItems should not be put under "items".
Fixes: 27bb0e4285 ("dt-bindings: memory: mediatek: Convert SMI to DT schema")
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220113111057.29918-2-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Bindings:
- DT schema conversions for Samsung clocks, RNG bindings, Qcom Command
DB and rmtfs, gpio-restart, i2c-mux-gpio, i2c-mux-pinctl, Tegra I2C
and BPMP, pwm-vibrator, Arm DSU, and Cadence macb
- DT schema conversions for Broadcom platforms: interrupt controllers,
STB GPIO, STB waketimer, STB reset, iProc MDIO mux, iProc PCIe,
Cygnus PCIe PHY, PWM, USB BDC, BCM6328 LEDs, TMON, SYSTEMPORT, AMAC,
Northstar 2 PCIe PHY, GENET, moca PHY, GISB arbiter, and SATA
- Add binding schemas for Tegra210 EMC table, TI DC-DC converters,
- Clean-ups of MDIO bus schemas to fix 'unevaluatedProperties' issues
- More fixes due to 'unevaluatedProperties' enabling
- Data type fixes and clean-ups of binding examples found in preparation
to move to validating DTB files directly (instead of intermediate YAML
representation.
- Vendor prefixes for T-Head Semiconductor, OnePlus, and Sunplus
- Add various new compatible strings
DT core:
- Silence a warning for overlapping reserved memory regions
- Reimplement unittest overlay tracking
- Fix stack frame size warning in unittest
- Clean-ups of early FDT scanning functions
- Fix handling of "linux,usable-memory-range" on EFI booted systems
- Add support for 'fail' status on CPU nodes
- Improve error message in of_phandle_iterator_next()
- kbuild: Disable duplicate unit-address warnings for disabled nodes
-----BEGIN PGP SIGNATURE-----
iQJEBAABCgAuFiEEktVUI4SxYhzZyEuo+vtdtY28YcMFAmHfCdcQHHJvYmhAa2Vy
bmVsLm9yZwAKCRD6+121jbxhw+UZD/0ZMQQ6VF20MW7Gg0bOutd8Q6Q6opjrCG5c
nLW5mv8Q+um3sI1ZpwdMI4zAfCmTfeL13ZM9KtJKlJ0o41bgId+kZsezy4I2rN9+
sE1CwA4TninKTJsUkmyQX4fgJRUZ95Eubryfb07sy7nbK3LZQ+t18R5tzVBDpzy4
7hy4eM6mlMxgIJDi7EUboLZslkMM4TGGutLsk5C5T5V5lcWSt3Jj5WZtl5k4Wykq
j4i9mU+GGTZi0nGAJQ7lNoLPatZDSVQx5tzNV/Wi8hSwZbn0Kycu+IuWZyihILz/
9lzB/7tv8fl+xkTaJ5xxaY05HcDeX02yCLzh3PfAHRYdbQ2EkFoaKqJ81SLfAq5t
aH87v41wFSrjzynxpppqswXOdqI/jofrHrGlQldnw0VHGTjEfDbyZGRQFPHmuzTG
gXaSNKCxppG7ThpXarfu7D4TdYV75n+cBOsC/BBopYgIS2+xmjDA3t5Scks1/4NX
1Hfq9IMF9iYJYc/GNXBWcOrLn9d1ILYt6HrKRQar1NIEFH1Lt0c2aw5WsyvOZ4zx
aLHLSbEwnl+2wleyGB9YQkFaaF7N6qcid3u9KFRJP6nTojoaeQaIi3MR9F3LVReZ
LV5YfWEcij1zc+lzwgHc6+8bbgFxrKgOC2IL/B6u93u/BO0wmF/54kbEZKaLyX8d
a7Iii4IYFw==
=2g8v
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"Bindings:
- DT schema conversions for Samsung clocks, RNG bindings, Qcom
Command DB and rmtfs, gpio-restart, i2c-mux-gpio, i2c-mux-pinctl,
Tegra I2C and BPMP, pwm-vibrator, Arm DSU, and Cadence macb
- DT schema conversions for Broadcom platforms: interrupt
controllers, STB GPIO, STB waketimer, STB reset, iProc MDIO mux,
iProc PCIe, Cygnus PCIe PHY, PWM, USB BDC, BCM6328 LEDs, TMON,
SYSTEMPORT, AMAC, Northstar 2 PCIe PHY, GENET, moca PHY, GISB
arbiter, and SATA
- Add binding schemas for Tegra210 EMC table, TI DC-DC converters,
- Clean-ups of MDIO bus schemas to fix 'unevaluatedProperties' issues
- More fixes due to 'unevaluatedProperties' enabling
- Data type fixes and clean-ups of binding examples found in
preparation to move to validating DTB files directly (instead of
intermediate YAML representation.
- Vendor prefixes for T-Head Semiconductor, OnePlus, and Sunplus
- Add various new compatible strings
DT core:
- Silence a warning for overlapping reserved memory regions
- Reimplement unittest overlay tracking
- Fix stack frame size warning in unittest
- Clean-ups of early FDT scanning functions
- Fix handling of "linux,usable-memory-range" on EFI booted systems
- Add support for 'fail' status on CPU nodes
- Improve error message in of_phandle_iterator_next()
- kbuild: Disable duplicate unit-address warnings for disabled nodes"
* tag 'devicetree-for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (114 commits)
dt-bindings: net: mdio: Drop resets/reset-names child properties
dt-bindings: clock: samsung: convert S5Pv210 to dtschema
dt-bindings: clock: samsung: convert Exynos5410 to dtschema
dt-bindings: clock: samsung: convert Exynos5260 to dtschema
dt-bindings: clock: samsung: extend Exynos7 bindings with UFS
dt-bindings: clock: samsung: convert Exynos7 to dtschema
dt-bindings: clock: samsung: convert Exynos5433 to dtschema
dt-bindings: i2c: maxim,max96712: Add bindings for Maxim Integrated MAX96712
dt-bindings: iio: adi,ltc2983: Fix 64-bit property sizes
dt-bindings: power: maxim,max17040: Fix incorrect type for 'maxim,rcomp'
dt-bindings: interrupt-controller: arm,gic-v3: Fix 'interrupts' cell size in example
dt-bindings: iio/magnetometer: yamaha,yas530: Fix invalid 'interrupts' in example
dt-bindings: clock: imx5: Drop clock consumer node from example
dt-bindings: Drop required 'interrupt-parent'
dt-bindings: net: ti,dp83869: Drop value on boolean 'ti,max-output-impedance'
dt-bindings: net: wireless: mt76: Fix 8-bit property sizes
dt-bindings: PCI: snps,dw-pcie-ep: Drop conflicting 'max-functions' schema
dt-bindings: i2c: st,stm32-i2c: Make each example a separate entry
dt-bindings: net: stm32-dwmac: Make each example a separate entry
dt-bindings: net: Cleanup MDIO node schemas
...
* mtdchar: Prevent unbounded allocation in MEMWRITE ioctl
* gen_probe: Use bitmap_zalloc() when applicable
* Introduce an expert mode for forensics and debugging purposes
* Clear out unregistered devices a bit more
* Provide unique name for nvmem device
* Remove unused header file <linux/mtd/latch-addr-flash.h>
* Fixed breaking list in __mtd_del_partition.
MTD device changes:
* sst25l, mchp48l640, mchp23k256, dataflash:
- Warn about failure to unregister mtd device
Raw NAND core changes:
* Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller changes:
* GPMC:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller changes:
* OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
* Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
* Onenand:
- Remove redundant variable ooblen
* MPC5121:
- Remove unused variable in ads5121_select_chip()
* GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
* Ingenic:
- JZ4740 needs 'oob_first' read page function
* Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
SPI NOR core changes:
* Add Pratyush as SPI NOR co-maintainer.
* Flash parameters initialization was done in a spaghetti way. Clean
flash parameters initialization.
* Rework the flash_info flags and clarify where one should be used.
* Initialize all flash parameters based on JESD216 SFDP where possible.
Flash parameters and settings that are SFDP discoverable should not be
duplicated via flash_info flags at flash declaration.
* Remove debugfs entries that duplicate sysfs entries.
SPI NOR manufacturer driver changes:
* Use late_init() hook in various drivers to make it clear that those
flash parameters are either not declared in the JESD216 SFDP standard,
or the SFDP tables which define those flash parameters are not defined
by the flash.
* Fix mtd size for s3an flashes.
* Write 2 bytes when disabling Octal DTR mode: 1 byte long transactions are
not allowed in 8D-8D-8D mode.
Hyperbus changes:
* Couple of fixes in Renesas hyperbus rpc-if driver to avoid crash on
module remove and for missing check for error value in probe.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmHO+g8ACgkQJWrqGEe9
VoRW1AgAjFC58ARNBw7asYerGyiUWv7b8RjPIRWZqmcSQ6D5m20cGNBTa15c2NrC
v0dNMf2+3FrCECso6wKPbkEbLt9lHjlMmt+AdlraV0QvHBXrJq/Tc2p2ATI5kTqq
WaP4oCx1mccgO+IrEIiGikOcFx/TLBBJEk+U0Anbm16eia9Cjw+uD/q7X2HbF5xQ
MOFZyQ+rAVqkM8tCh6VHhCpX85pn9pj2ZdouOhPWsqjULaGqDbUopC70YPZLVJyx
9u4xHFaVLVae6AS5Gitser2ie8klypTN/H+1weSao43GGmwIrT0wK0mCOVIm90Zd
4frlpnt4QE/IIAKgAm+HxkWg+KV9qg==
=E8lV
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD core changes:
- mtdchar: Prevent unbounded allocation in MEMWRITE ioctl
- gen_probe: Use bitmap_zalloc() when applicable
- Introduce an expert mode for forensics and debugging purposes
- Clear out unregistered devices a bit more
- Provide unique name for nvmem device
- Remove unused header file <linux/mtd/latch-addr-flash.h>
- Fixed breaking list in __mtd_del_partition.
MTD device changes:
- Warn about failure to unregister mtd device in sst25l, mchp48l640,
mchp23k256, and dataflash drivers.
Raw NAND core changes:
- Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller changes:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller changes:
- OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
- Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
- Onenand:
- Remove redundant variable ooblen
- MPC5121:
- Remove unused variable in ads5121_select_chip()
- GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
- Ingenic:
- JZ4740 needs 'oob_first' read page function
- Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
SPI NOR core changes:
- Add Pratyush as SPI NOR co-maintainer.
- Flash parameters initialization was done in a spaghetti way. Clean
flash parameters initialization.
- Rework the flash_info flags and clarify where one should be used.
- Initialize all flash parameters based on JESD216 SFDP where
possible. Flash parameters and settings that are SFDP discoverable
should not be duplicated via flash_info flags at flash declaration.
- Remove debugfs entries that duplicate sysfs entries.
SPI NOR manufacturer driver changes:
- Use late_init() hook in various drivers to make it clear that those
flash parameters are either not declared in the JESD216 SFDP
standard, or the SFDP tables which define those flash parameters
are not defined by the flash.
- Fix mtd size for s3an flashes.
- Write 2 bytes when disabling Octal DTR mode: 1 byte long
transactions are not allowed in 8D-8D-8D mode.
Hyperbus changes:
- Couple of fixes in Renesas hyperbus rpc-if driver to avoid crash on
module remove and for missing check for error value in probe"
* tag 'mtd/for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (71 commits)
mtd: spi-nor: Remove debugfs entries that duplicate sysfs entries
mtd: spi-nor: micron-st: write 2 bytes when disabling Octal DTR mode
mtd: spi-nor: spansion: write 2 bytes when disabling Octal DTR mode
mtd: spi-nor: core: use 2 data bytes for template ops
mtd: spi-nor: Constify part specific fixup hooks
mtd: spi-nor: core: Remove reference to spi-nor.c
mtd: rawnand: gpmi: Use platform_get_irq_byname() to get the interrupt
mtd: rawnand: omap_elm: Use platform_get_irq() to get the interrupt
mtd: rawnand: omap2: Select GPMC device driver for ARCH_K3
memory: omap-gpmc: Use a compatible match table when checking for NAND controller
memory: omap-gpmc: Add support for GPMC on AM64 SoC
dt-bindings: memory-controllers: ti,gpmc: Add compatible for AM64
memory: omap-gpmc: Use platform_get_irq() to get the interrupt
MAINTAINERS: Add an entry for Renesas NAND controller
mtd: rawnand: renesas: Add new NAND controller driver
dt-bindings: mtd: renesas: Describe Renesas R-Car Gen3 & RZ/N1 NAND controller
mtd: rawnand: gpmi: remove unneeded variable
mtd: rawnand: omap2: drop unused variable
mtd: rawnand: omap2: fix force_8bit flag behaviour for DMA mode
mtd: rawnand: omap2: Add compatible for AM64 SoC
...
- Add support for DRR5 and new models 0x10-0x1f and 0x50-0x5f of AMD
family 0x19 CPUs to amd64_edac
- The usual set of fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=85ZE
-----END PGP SIGNATURE-----
Merge tag 'edac_updates_for_v5.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC updates from Borislav Petkov:
- Add support for version 3 of the Synopsys DDR controller to
synopsys_edac
- Add support for DRR5 and new models 0x10-0x1f and 0x50-0x5f of AMD
family 0x19 CPUs to amd64_edac
- The usual set of fixes and cleanups
* tag 'edac_updates_for_v5.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/amd64: Add support for family 19h, models 50h-5fh
EDAC/sb_edac: Remove redundant initialization of variable rc
RAS/CEC: Remove a repeated 'an' in a comment
EDAC/amd64: Add support for AMD Family 19h Models 10h-1Fh and A0h-AFh
EDAC: Add RDDR5 and LRDDR5 memory types
EDAC/sifive: Fix non-kernel-doc comment
dt-bindings: memory: Add entry for version 3.80a
EDAC/synopsys: Enable the driver on Intel's N5X platform
EDAC/synopsys: Add support for version 3 of the Synopsys EDAC DDR
EDAC/synopsys: Use the quirk for version instead of ddr version
As usual, this is the bulk of the updates for the SoC tree, adding
more devices to existing files, addressing issues from ever improving
automated checking, and fixing minor issues.
The most interesting bits as usual are the new platforms.
All the newly supported SoCs belong into existing families
this time:
- Qualcomm gets support for two newly announced platforms, both
of which can now work in production environments: the SDX65
5G modem that can run a minimal Linux on its Cortex-A7 core,
and the Snapdragon 8 Gen 1, their latest high-end phone SoC.
- Renesas adds support for R-Car S4-8, the most recent automotive
Server/Communication SoC.
- TI adds support for J721s2, a new automotive SoC in the K3
family.
- Mediatek MT7986a/b is a SoC used in Wifi routers, the latest
generation following their popular MT76xx series. Only basic
support is added for now.
- NXP i.MX8 ULP8 is a new low-power variant of the widespread
i.MX8 series.
- TI SPEAr320s is a minor variant of the old SPEAr320 SoC that
we have supported for a long time.
New boards with the existing SoCs include
- Aspeed AST2500/AST2600 BMCs in TYAN, Facebook and Yadro servers
- AT91/SAMA5 based evaluation board
- NXP gains twenty new development and industrial boards for their
i.MX and Layerscape SoCs
- Intel IXP4xx now supports the final two machines in device tree
that were previously only supported in old style board files.
- Mediatek MT6589 is used in the Fairphone FP1 phone from 2013,
while MT8183 is used in the Acer Chromebook 314.
- Qualcomm gains support for the reference machines using the two
new SoCs, plus a number of Chromebook variants and phones based
on the Snapdragon 7c, 845 and 888 SoCs, including various
Sony Xperia devices and the Microsoft Surface Duo 2.
- ST STM32 now supports the Engicam i.Core STM32MP1 carrier board.
- Tegra now boots various older Android devices based on 32-bit
chips out of the box, including a number of ASUS Transformer
tablets.
There is also a new Jetson AGX Orin developer kit.
- Apple support adds the missing device trees for all the remaining
M1 Macbook and iMac variants, though not yet the M1 Pro/Max
versions.
- Allwinner now supports another version of the Tanix TX6 set-top
box based on the H6 SoC.
- Broadcom gains support for the Netgear RAXE500 Wireless router
based on BCM4908.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmHDsm4ACgkQmmx57+YA
GNm9YhAAm0c/uPAkDA/6ESjaMC5qIHnV8CC9ZV24iINqFutcjKm2az8OiqKZT7UW
a/+n2sfjAiyoAAaXrp/WvyMH2Sula1i/OZpR4GYIbD/lbYRFk+4+iW2YY9vViCjL
KH6M/H6KfOSNmGcpe3wDvu7D4YWfFKDCDyUJsEaMW2xSQehYbH5P0OuzQW1EROHr
GQp60QtCbUpMmqIrkJT99MxBGCCyb4dV6BT3iU489/YU3q3pOF8OWMLKv5TlXzfw
x0pLH5CKavvCFj3iqp80sCEBeSoUecLKVnBRfmwAH1vgfNrhpXh4jP9m1e3Vh3Bb
aJGZ57W77Akf+TywZEojDdIDQGKcdlzpZNxN2i4e4+LECYvfOdJW8GP18MmsXEY4
apb0NeKad8FGRI4b97dIVEcTa894JkEZaEtnNaIdjWFhBgzO+Kr2iOTw71AKsJmc
eIwv4SDdUQTU4VT08ceJTOVt8NikGALJStg5knpVJ9lfHvFlWj1GAE4QnCtS6pUR
iiyqJ1/7khNplcgowaz6nuC2gSE49UwYQImLvBfG17eT1YU3B2OZg/FZ9xSmr2bW
Thk+TKO9A6xai8QQWYV99Ae+Y6nDWUrLL5U9DXTn4cm64g5z3VkVKGcNajg/kAad
hyQmSIhcypp2KN//c+d3VU/KY1EUYJDzg1EEwRuxP7Gih5/7pb8=
=IF3G
-----END PGP SIGNATURE-----
Merge tag 'dt-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC devicetree updates from Arnd Bergmann:
"As usual, this is the bulk of the updates for the SoC tree, adding
more devices to existing files, addressing issues from ever improving
automated checking, and fixing minor issues.
The most interesting bits as usual are the new platforms. All the
newly supported SoCs belong into existing families this time:
- Qualcomm gets support for two newly announced platforms, both of
which can now work in production environments: the SDX65 5G modem
that can run a minimal Linux on its Cortex-A7 core, and the
Snapdragon 8 Gen 1, their latest high-end phone SoC.
- Renesas adds support for R-Car S4-8, the most recent automotive
Server/Communication SoC.
- TI adds support for J721s2, a new automotive SoC in the K3 family.
- Mediatek MT7986a/b is a SoC used in Wifi routers, the latest
generation following their popular MT76xx series. Only basic
support is added for now.
- NXP i.MX8 ULP8 is a new low-power variant of the widespread i.MX8
series.
- TI SPEAr320s is a minor variant of the old SPEAr320 SoC that we
have supported for a long time.
New boards with the existing SoCs include
- Aspeed AST2500/AST2600 BMCs in TYAN, Facebook and Yadro servers
- AT91/SAMA5 based evaluation board
- NXP gains twenty new development and industrial boards for their
i.MX and Layerscape SoCs
- Intel IXP4xx now supports the final two machines in device tree
that were previously only supported in old style board files.
- Mediatek MT6589 is used in the Fairphone FP1 phone from 2013, while
MT8183 is used in the Acer Chromebook 314.
- Qualcomm gains support for the reference machines using the two new
SoCs, plus a number of Chromebook variants and phones based on the
Snapdragon 7c, 845 and 888 SoCs, including various Sony Xperia
devices and the Microsoft Surface Duo 2.
- ST STM32 now supports the Engicam i.Core STM32MP1 carrier board.
- Tegra now boots various older Android devices based on 32-bit chips
out of the box, including a number of ASUS Transformer tablets.
There is also a new Jetson AGX Orin developer kit.
- Apple support adds the missing device trees for all the remaining
M1 Macbook and iMac variants, though not yet the M1 Pro/Max
versions.
- Allwinner now supports another version of the Tanix TX6 set-top box
based on the H6 SoC.
- Broadcom gains support for the Netgear RAXE500 Wireless router
based on BCM4908"
* tag 'dt-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (574 commits)
Revert "ARM: dts: BCM5301X: define RTL8365MB switch on Asus RT-AC88U"
arm64: dts: qcom: sm6125: Avoid using missing SM6125_VDDCX
arm64: dts: qcom: sm8450-qrd: Enable USB nodes
arm64: dts: qcom: sm8450: Add usb nodes
ARM: dts: aspeed: add LCLK setting into LPC KCS nodes
dt-bindings: ipmi: bt-bmc: add 'clocks' as a required property
ARM: dts: aspeed: add LCLK setting into LPC IBT node
ARM: dts: aspeed: p10: Add TPM device
ARM: dts: aspeed: p10: Enable USB host ports
ARM: dts: aspeed: Add TYAN S8036 BMC machine
ARM: dts: aspeed: tyan-s7106: Add uart_routing and fix vuart config
ARM: dts: aspeed: Adding Facebook Bletchley BMC
ARM: dts: aspeed: g220a: Enable secondary flash
ARM: dts: Add openbmc-flash-layout-64-alt.dtsi
ARM: dts: aspeed: Add secure boot controller node
dt-bindings: aspeed: Add Secure Boot Controller bindings
ARM: dts: Remove "spidev" nodes
dt-bindings: pinctrl: samsung: Add pin drive definitions for Exynos850
dt-bindings: arm: samsung: Document E850-96 board binding
dt-bindings: Add vendor prefix for WinLink
...
AM64 SoC contains the GPMC module. Add compatible for it.
Newer SoCs don't necessarily map GPMC data region at the same place
as legacy SoCs. Add reg-names "data", to provide this information to
the device driver.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211221131757.2030-2-rogerq@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Document the variant of the memory controller and external memory
controllers found on Tegra234 and add some memory client and SMMU
stream ID definitions for use in device tree files.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The #interconnect-cells properties are required to hook up memory
clients to the MC/EMC in interconnects properties. Add a description for
these properties.
For the nested EMC controller, the list of required properties was
missing. Add it so that the validation can be more strict.
Also, allow multiple reg entries required by Tegra194 and later.
While at it, also remove the dummy BPMP node from the example because it
is incomplete and fails validation. It's also not necessary for this
file and the BPMP DT schema already has a full example.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
With 'unevaluatedProperties' support implemented, the TI GPMC example
has a warning:
Documentation/devicetree/bindings/mtd/ti,gpmc-onenand.example.dt.yaml: memory-controller@6e000000: onenand@0,0: Unevaluated properties are not allowed ('compatible', '#address-cells', '#size-cells', 'partition@0', 'partition@100000' were unexpected)
The child node definition for GPMC is not a complete binding, so specifying
'unevaluatedProperties: false' for it is not correct and should be
dropped.
Fixup the unnecessary 'allOf' while we're here.
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211206174215.2297796-1-robh@kernel.org
SPI Multi I/O Bus Controller on RZ/G2L SoC is almost identical to
the RPC-IF interface found on R-Car Gen3 SoC's.
This patch adds a new compatible string to identify the RZ/G2L family
so that the timing values on RZ/G2L can be adjusted.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211025205631.21151-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Not all @st.com email address are concerned, only people who have
a specific @foss.st.com email will see their entry updated.
For some people, who left the company, remove their email.
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Cc: Fabien Dessenne <fabien.dessenne@foss.st.com>
Cc: Christophe Roullier <christophe.roullier@foss.st.com>
Cc: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Cc: Lionel Debieve <lionel.debieve@foss.st.com>
Cc: Amelie Delaunay <amelie.delaunay@foss.st.com>
Cc: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Cc: Ludovic Barre <ludovic.barre@foss.st.com>
Cc: Christophe Kerello <christophe.kerello@foss.st.com>
Cc: pascal Paillet <p.paillet@foss.st.com>
Cc: Erwan Le Ray <erwan.leray@foss.st.com>
Cc: Philippe CORNU <philippe.cornu@foss.st.com>
Cc: Yannick Fertre <yannick.fertre@foss.st.com>
Cc: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Cc: Olivier Moysan <olivier.moysan@foss.st.com>
Cc: Hugues Fruchet <hugues.fruchet@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20211110150144.18272-6-patrice.chotard@foss.st.com
Signed-off-by: Rob Herring <robh@kernel.org>
Tidy up a bit the tree, by prefixing all include/dt-bindings/clock/ files
related to Ingenic SoCs with 'ingenic,'.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211016133322.40771-1-paul@crapouillou.net
These are all the driver updates for SoC specific drivers. There
are a couple of subsystems with individual maintainers picking up
their patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this
tree this time. There are only minor changes, but they depend
on other tegra driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process.
This depends on a small sound driver change that is included
here as well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains
a mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for
the "Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed
BMCs, something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better suspend/resume
support
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx, layerscape,
allwinner, broadcom, and omap.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmGCvKgACgkQmmx57+YA
GNnNfw/8DDTfMUycVvtaNslYlWri0/2O0nSqhNIIbTAcVuD/x5qo/McDhKuv+ldM
BoTDMjRYZfQkrNXSEj3MaxB9E0o6Srva5SM8y4+Koe0VVtvEVovjYkXOhXqSEWWl
aqVIe0S6Y1rF/KxJlvAfGxYHb5d+6aYqzdmhjURpXNGxqpSHb9/hqisY97Q9TpnD
6lQZOz9d1JNDq0eOh1qjcfuMjg1EHZHDZJyioCvyX38KIl2q7p3ll2z/eqrrDhQZ
TrvL/YVosTXqBcAfi47Oz+n/CX2i0MrjVO8nfPSGOq5UL4Al3SZD4XYY96IOIQrH
+XGFigGGAkV2LfKSEPNJWaq7g+SiQUr2jc3p8b4Zxde8/+5M127/gotiPddyG2LX
1OnFRnPskgRApGqHjGEcEzzJUTag7Hc+YVH82TMEHZhSDMq6i30k9UnyfXsziZDV
8CrkOpjuSg+YxFv/83bfa1pIoYtFfjGr16mq4muajodnX7+b7My9iv+2Oo2iQM9y
DwRUKj7+eap23SEUpi4et6HlNpoF6yJMbt5Ae1k+gTK2DvQ4Cx6n4QJz/I7WC1Wp
BdVhvSH8XVppVLtQqODud+VWvLgLerRxUpGRdbS8r5VsnNUJTvaS4YGMpm9616G7
TrgUSSvsyu1lLqbWMh+pOCk4l3r64vSUn581hrIw6jtioNGvMdE=
=tUuj
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are all the driver updates for SoC specific drivers. There are a
couple of subsystems with individual maintainers picking up their
patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this tree this
time. There are only minor changes, but they depend on other tegra
driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process. This
depends on a small sound driver change that is included here as
well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains a
mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for the
"Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed BMCs,
something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better
suspend/resume support"
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx,
layerscape, allwinner, broadcom, and omap"
* tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (179 commits)
optee: Fix spelling mistake "reclain" -> "reclaim"
Revert "firmware: qcom: scm: Add support for MC boot address API"
qcom: spm: allow compile-testing
firmware: arm_ffa: Remove unused 'compat_version' variable
soc: samsung: exynos-chipid: add exynosautov9 SoC support
firmware: qcom: scm: Don't break compile test on non-ARM platforms
soc: qcom: smp2p: Add of_node_put() before goto
soc: qcom: apr: Add of_node_put() before return
soc: qcom: qcom_stats: Fix client votes offset
soc: qcom: rpmhpd: fix sm8350_mxc's peer domain
dt-bindings: arm: cpus: Document qcom,msm8916-smp enable-method
ARM: qcom: Add qcom,msm8916-smp enable-method identical to MSM8226
firmware: qcom: scm: Add support for MC boot address API
soc: qcom: spm: Add 8916 SPM register data
dt-bindings: soc: qcom: spm: Document qcom,msm8916-saw2-v3.0-cpu
soc: qcom: socinfo: Add PM8150C and SMB2351 models
firmware: qcom_scm: Fix error retval in __qcom_scm_is_call_available()
soc: aspeed: Add UART routing support
soc: fsl: dpio: rename the enqueue descriptor variable
soc: fsl: dpio: use an explicit NULL instead of 0
...
This is a rather large update for the ARM devicetree files, after a few
quieter releases, with 775 total commits and 47 branches pulled into
this one. There are 5 new SoC types plus some minor variations, and
a total of 60 new machines, so I'm limiting the summary to the main
noteworthy items:
- Apple M1 gain support for PCI and pinctrl, getting a bit
closer to a usable system out of the box.
- Qualcomm gains support for Snapdragon 690 (aka SM6350) as
well as SM7225, 11 new smartphones, and three additional
Chromebooks, and improvements all over the place.
- Samsung gains support for ExynosAutov9, an automotive version
of their smartphone SoC, but otherwise no major changes.
- Microchip adds the SAMA5D29 SoC in the SAMA5 family, and a
number of improvements for the recently added SAMA7 family.
The LAN966 SoC that was added in the platform code does not
have dts files yet. Two board files are added for the older
at91sam9g20 SoC
- Aspeed supports two additional server boards using their AST2600
as BMC, and improves support for qemu models
- Rockchip RK3566/RK3688 gets added, along with six new
development boards using RK3328/RK3399/RK3566, and one
Chromebook tablet.
- Two NAS boxes are added using the ARMv4 based Gemini platform
- One new board is added to the Intel Arria SoC FPGA family
- Marvell adds one network switch based on Armada 381 and the
new MOCHAbin 7040 development board
- NXP adds support for the S32G2 automotive SoC, two imx6 based
ebook readers, and three additional development boards, which
is notably less than their usual additions, but they also gain
improvements to their many existing boards
- STmicroelectronics adds their stm32mp13 SoC family along with
a reference board
- Renesas adds new versions of their R-Car Gen3 SoCs and many
updates for their older generations
- Broadcom adds support for a number of Cisco Meraki wireless
controllers, along with two new boards and other updates for
BCM53xx/BCM47xx networking SoCs and the Raspberry Pi
boards
- Mediatek improves support for the MT81xx SoCs used in Chromebooks
as well as the MT76xx networking SoCs
- NVIDIA adds a number of cleanups and additional support for
more hardware on the already supported machines
- TI K3 adds support for three new boards along with cleanups
- Toshiba adds one board for the Visconti family
- Xilinx adds five new ZynqMP based machines
- Amlogic support is added for the Radxa Zero and two Jethub
home automation controllers, along with changes to other
machines
- Rob Herring continues his work on fixing dtc warnings all over
the tree.
- Minor updates for TI OMAP, Mstar, Allwinner/sunxi, Hisilicon,
Ux500, Unisoc
-----BEGIN PGP SIGNATURE-----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=jp4P
-----END PGP SIGNATURE-----
Merge tag 'dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC DT updates from Arnd Bergmann:
"This is a rather large update for the ARM devicetree files, after a
few quieter releases, with 775 total commits and 47 branches pulled
into this one.
There are 5 new SoC types plus some minor variations, and a total of
60 new machines, so I'm limiting the summary to the main noteworthy
items:
- Apple M1 gain support for PCI and pinctrl, getting a bit closer to
a usable system out of the box.
- Qualcomm gains support for Snapdragon 690 (aka SM6350) as well as
SM7225, 11 new smartphones, and three additional Chromebooks, and
improvements all over the place.
- Samsung gains support for ExynosAutov9, an automotive version of
their smartphone SoC, but otherwise no major changes.
- Microchip adds the SAMA5D29 SoC in the SAMA5 family, and a number
of improvements for the recently added SAMA7 family. The LAN966 SoC
that was added in the platform code does not have dts files yet.
Two board files are added for the older at91sam9g20 SoC
- Aspeed supports two additional server boards using their AST2600 as
BMC, and improves support for qemu models
- Rockchip RK3566/RK3688 gets added, along with six new development
boards using RK3328/RK3399/RK3566, and one Chromebook tablet.
- Two NAS boxes are added using the ARMv4 based Gemini platform
- One new board is added to the Intel Arria SoC FPGA family
- Marvell adds one network switch based on Armada 381 and the new
MOCHAbin 7040 development board
- NXP adds support for the S32G2 automotive SoC, two imx6 based ebook
readers, and three additional development boards, which is notably
less than their usual additions, but they also gain improvements to
their many existing boards
- STmicroelectronics adds their stm32mp13 SoC family along with a
reference board
- Renesas adds new versions of their R-Car Gen3 SoCs and many updates
for their older generations
- Broadcom adds support for a number of Cisco Meraki wireless
controllers, along with two new boards and other updates for
BCM53xx/BCM47xx networking SoCs and the Raspberry Pi boards
- Mediatek improves support for the MT81xx SoCs used in Chromebooks
as well as the MT76xx networking SoCs
- NVIDIA adds a number of cleanups and additional support for more
hardware on the already supported machines
- TI K3 adds support for three new boards along with cleanups
- Toshiba adds one board for the Visconti family
- Xilinx adds five new ZynqMP based machines
- Amlogic support is added for the Radxa Zero and two Jethub home
automation controllers, along with changes to other machines
- Rob Herring continues his work on fixing dtc warnings all over the
tree.
- Minor updates for TI OMAP, Mstar, Allwinner/sunxi, Hisilicon,
Ux500, Unisoc"
* tag 'dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (720 commits)
arm64: dts: apple: j274: Expose PCI node for the Ethernet MAC address
arm64: dts: apple: t8103: Add root port interrupt routing
arm64: dts: apple: t8103: Add PCIe DARTs
arm64: apple: Add PCIe node
arm64: apple: Add pinctrl nodes
ARM: dts: arm: Update ICST clock nodes 'reg' and node names
ARM: dts: arm: Update register-bit-led nodes 'reg' and node names
arm64: dts: exynos: add chipid node for exynosautov9 SoC
ARM: dts: qcom: fix typo in IPQ8064 thermal-sensor node
Revert "arm64: dts: qcom: msm8916-asus-z00l: Add sensors"
arm64: dts: qcom: ipq6018: Remove unused 'iface_clk' property from dma-controller node
arm64: dts: qcom: ipq6018: Remove unused 'qcom,config-pipe-trust-reg' property
arm64: dts: qcom: sm8350: Add CPU topology and idle-states
arm64: dts: qcom: Drop unneeded extra device-specific includes
arm64: dts: qcom: msm8916: Drop standalone smem node
arm64: dts: qcom: Fix node name of rpm-msg-ram device nodes
arm64: dts: qcom: msm8916-asus-z00l: Add sensors
arm64: dts: qcom: msm8916-asus-z00l: Add SDCard
arm64: dts: qcom: msm8916-asus-z00l: Add touchscreen
arm64: dts: qcom: sdm845-oneplus: remove devinfo-size from ramoops node
...
Some Tegra20 boards don't have RAM code stored in NVMEM, which is used for
the memory chip identification and the identity information should be read
out from LPDDR2 chip in this case. Document new sub-node containing generic
LPDDR2 properties that will be used for the memory chip identification if
RAM code isn't available. The identification is done by reading out memory
configuration values from generic LPDDR2 mode registers of SDRAM chip and
comparing them with the values of device-tree 'lpddr2' sub-node.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211006224659.21434-8-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Elpida B8132B2PB-6D-F memory chip is used by ASUS Transformer TF101
tablet, add compatible for it. We need to specify this compatible it
for a device-tree node containing corresponding memory timings in order
to allow software to match the timings with the detected hardware.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211006224659.21434-5-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Add optional revision-id standard LPDDR2 properties which will help to
identify memory chip.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211006224659.21434-4-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Convert LPDDR2 binding to schema. I removed obsolete ti,jedec-lpddr2-*
compatibles since they were never used by device-trees and by the code.
I also changed "Elpida" compatible prefix to lowercase "elpida".
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211006224659.21434-3-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Move DDR bindings to memory-controllers directory to make them more
discoverable.
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211006224659.21434-2-digetx@gmail.com
[krzysztof: Correct path in lpddr3.txt and samsung,exynos5422-dmc.yaml]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
1. Renesas RPC: fix unaligned bus access and QSPI data transfers in
manual modes.
2. Renesas RPC: select RESET_CONTROLLER as it is necessary for
operation.
3. FSL IFC: fix error paths.
4. Broadcom: allow building as module.
-----BEGIN PGP SIGNATURE-----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=ZsTv
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=OOXj
-----END PGP SIGNATURE-----
Merge tag 'memory-controller-drv-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/drivers
Memory controller drivers for v5.16
1. Renesas RPC: fix unaligned bus access and QSPI data transfers in
manual modes.
2. Renesas RPC: select RESET_CONTROLLER as it is necessary for
operation.
3. FSL IFC: fix error paths.
4. Broadcom: allow building as module.
* tag 'memory-controller-drv-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
memory: fsl_ifc: fix leak of irq and nand_irq in fsl_ifc_ctrl_probe
memory: renesas-rpc-if: RENESAS_RPCIF should select RESET_CONTROLLER
memory: brcmstb_dpfe: Allow building Broadcom STB DPFE as module
memory: samsung: describe drivers in KConfig
memory: renesas-rpc-if: Avoid unaligned bus access for HyperFlash
memory: renesas-rpc-if: Correct QSPI data transfer in Manual mode
dt-bindings: rpc: renesas-rpc-if: Add support for the R8A779A0 RPC-IF
Link: https://lore.kernel.org/r/20211010175836.13302-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Convert omap-gpmc.txt to ti,gpmc.yaml.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This binding is meant for the child nodes of the TI GPMC node. The node
represents any device connected to the GPMC bus. It may be a Flash chip,
RAM chip or Ethernet controller, etc. These properties are meant for
configuring the GPMC settings/timings and will accompany the bindings
supported by the respective device.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the binding for smi-sub-common. The SMI block diagram like this:
IOMMU
| |
smi-common
------------------
| .... |
larb0 larb7 <-max is 8
The smi-common connects with smi-larb and IOMMU. The maximum larbs number
that connects with a smi-common is 8. If the engines number is over 8,
sometimes we use a smi-sub-common which is nearly same with smi-common.
It supports up to 8 input and 1 output(smi-common has 2 output)
Something like:
IOMMU
| |
smi-common
---------------------
| | ...
larb0 sub-common ... <-max is 8
-----------
| | ... <-max is 8 too.
larb2 larb5
We don't need extra SW setting for smi-sub-common, only the sub-common has
special clocks need to enable when the engines access dram.
If it is sub-common, it should have a "mediatek,smi" phandle to point to
its smi-common. meanwhile the sub-common only has one gals clock.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210914113703.31466-3-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Add mt8195 smi supporting in the bindings.
In mt8195, there are two smi-common HW, one is for vdo(video output),
the other is for vpp(video processing pipe). They connect with different
smi-larbs, then some setting(bus_sel) is different. Differentiate them
with the compatible string.
Something like this:
IOMMU(VDO) IOMMU(VPP)
| |
SMI_COMMON_VDO SMI_COMMON_VPP
---------------- ----------------
| | ... | | ...
larb0 larb2 ... larb1 larb3 ...
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210914113703.31466-2-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Convert Freescale/NXP DDR memory controller bindings to DT schema format
using json-schema.
Previous bindings were not listing all compatibles, so scan through
devicetree sources and drivers to get these.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210826113049.92962-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Rob Herring <robh@kernel.org>
Convert Samsung Exynos5422 SoC frequency and voltage scaling for
Dynamic Memory Controller to DT schema format using json-schema.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20210820150353.161161-3-krzysztof.kozlowski@canonical.com
Signed-off-by: Rob Herring <robh@kernel.org>
Convert H8/300 bus controller bindings to DT schema format using
json-schema.
The conversion also extends the bindings to match what is really used in
existing devicetree sources (the original file mentions only
"renesas,h8300-bsc" but "renesas,h8300h-bsc" and "renesas,h8s-bsc" are
used with it).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210818202953.16862-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Rob Herring <robh@kernel.org>
Convert Synopsys IntelliDDR Multi Protocol memory controller (present in
Xilinx Zynq and ZynqMP) bindings to DT schema format using json-schema.
New binding contains copied parts of description from previous binding
document, therefore the license is set as GPL-2.0-only.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210818113139.84869-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Rob Herring <robh@kernel.org>
Convert Broadcom DDR PHY Front End (DPFE) bindings to DT schema format
using json-schema.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Markus Mayer <mmayer@broadcom.com>
Link: https://lore.kernel.org/r/20210817080617.14503-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Rob Herring <robh@kernel.org>
Another round of removing redundant minItems/maxItems from new schema in
the recent merge window.
If a property has an 'items' list, then a 'minItems' or 'maxItems' with the
same size as the list is redundant and can be dropped. Note that is DT
schema specific behavior and not standard json-schema behavior. The tooling
will fixup the final schema adding any unspecified minItems/maxItems.
This condition is partially checked with the meta-schema already, but
only if both 'minItems' and 'maxItems' are equal to the 'items' length.
An improved meta-schema is pending.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Will Deacon <will@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-clk@vger.kernel.org
Cc: iommu@lists.linux-foundation.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-rtc@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20210713193453.690290-1-robh@kernel.org
* Convert list_for_each to entry variant
* Use MTD_DEVICE_ATTR_RO/RW() helper macros
* Remove unnecessary OOM messages
* Potential NULL dereference in mtd_otp_size()
* Fix freeing of otp_info buffer
* Create partname and partid debug files for child MTDs
* tests:
- Remove redundant assignment to err
- Fix error return code in mtd_oobtest_init()
* Add OTP NVMEM provider support
* Allow specifying of_node
* Convert sysfs sprintf/snprintf family to sysfs_emit
Bindings changes:
* Convert ti,am654-hbmc.txt to YAML schema
* spi-nor: add otp property
* Add OTP bindings
* add YAML schema for the generic MTD bindings
* Add brcm,trx-magic
MTD device drivers changes:
* Add support for microchip 48l640 EERAM
* Remove superfluous "break"
* sm_ftl:
- Fix alignment of block comment
* nftl:
- Return -ENOMEM when kmalloc failed
* nftlcore:
- Remove set but rewrite variables
* phram:
- Fix error return code in phram_setup()
* plat-ram:
- Remove redundant dev_err call in platram_probe()
MTD parsers changes:
* Qcom:
- Fix leaking of partition name
* Redboot:
- Fix style issues
- Seek fis-index-block in the right node
* trx:
- Allow to use TRX parser on Mediatek SoCs
- Allow to specify brcm, trx-magic in DT
Raw NAND core:
* Allow SDR timings to be nacked
* Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing set.
* Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
* Update dead URL
* Silence static checker warning in nand_setup_interface()
* BBT:
- Fix corner case in bad block table handling
* onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
* Atmel:
- Ensure the data interface is supported.
* Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
* brcmnand:
- Convert bindings to json-schema
* OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
* PL35X:
- New driver
* QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
* Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in marvell_nfc_resume()
* R852:
- Use DEVICE_ATTR_RO() helper macro
* MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
* HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
* Light reorganisation for the introduction of a core resume handler
* Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
* Macronix:
- Add support for serial NAND flash
SPI NOR core changes:
* Ability to dump SFDP tables via sysfs
* Support for erasing OTP regions on Winbond and similar flashes
* Few API doc updates and fixes
* Locking support for MX25L12805D
SPI NOR controller drivers changes:
* Use SPI_MODE_X_MASK in nxp-spifi
* Intel Alder Lake-M SPI serial flash support
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmDcT+IACgkQJWrqGEe9
VoT5Sgf/dt92XA5K2SYNh58KPUwemB9DtkukmniGjo9AqSQwuzHxik3ITHBbFvwP
cSj5PAGoI+zpc+VQz+XuZF1Bsmxaqhy5c0aaJ9TZai2W6keB91in7nJPAhmAI5o2
4zhtAZ9qKp4pOwhFqn6jTd5+l38ok50go3HB4Ibw4UlLuvbUEv11DUcXGKnaAadH
tmXZALf65YAJVruPb4yw+cv7BVVgOPQL8C8ILtsrue7Zgya3JT1205Zbfdjo+X0v
Kl2gh7gGh1YLqzuLLBDUiDnfLIfiu/WTnPqxtqCULR9cLG4oXybXHZe9OsrP8E+P
T68+K8VvT5LKbGh47/OoUfLvrDguCA==
=XVaS
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- Convert list_for_each to entry variant
- Use MTD_DEVICE_ATTR_RO/RW() helper macros
- Remove unnecessary OOM messages
- Potential NULL dereference in mtd_otp_size()
- Fix freeing of otp_info buffer
- Create partname and partid debug files for child MTDs
- tests:
- Remove redundant assignment to err
- Fix error return code in mtd_oobtest_init()
- Add OTP NVMEM provider support
- Allow specifying of_node
- Convert sysfs sprintf/snprintf family to sysfs_emit
Bindings changes:
- Convert ti,am654-hbmc.txt to YAML schema
- spi-nor: add otp property
- Add OTP bindings
- add YAML schema for the generic MTD bindings
- Add brcm,trx-magic
MTD device drivers changes:
- Add support for microchip 48l640 EERAM
- Remove superfluous "break"
- sm_ftl:
- Fix alignment of block comment
- nftl:
- Return -ENOMEM when kmalloc failed
- nftlcore:
- Remove set but rewrite variables
- phram:
- Fix error return code in phram_setup()
- plat-ram:
- Remove redundant dev_err call in platram_probe()
MTD parsers changes:
- Qcom:
- Fix leaking of partition name
- Redboot:
- Fix style issues
- Seek fis-index-block in the right node
- trx:
- Allow to use TRX parser on Mediatek SoCs
- Allow to specify brcm, trx-magic in DT
Raw NAND core:
- Allow SDR timings to be nacked
- Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing
set.
- Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
- Update dead URL
- Silence static checker warning in nand_setup_interface()
- BBT:
- Fix corner case in bad block table handling
- onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
- Atmel:
- Ensure the data interface is supported.
- Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
- brcmnand:
- Convert bindings to json-schema
- OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
- PL35X:
- New driver
- QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
- Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in
marvell_nfc_resume()
- R852:
- Use DEVICE_ATTR_RO() helper macro
- MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
- HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
- Light reorganisation for the introduction of a core resume handler
- Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
- Macronix:
- Add support for serial NAND flash
SPI NOR core changes:
- Ability to dump SFDP tables via sysfs
- Support for erasing OTP regions on Winbond and similar flashes
- Few API doc updates and fixes
- Locking support for MX25L12805D
SPI NOR controller drivers changes:
- Use SPI_MODE_X_MASK in nxp-spifi
- Intel Alder Lake-M SPI serial flash support"
* tag 'mtd/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (125 commits)
mtd: spi-nor: remove redundant continue statement
mtd: rawnand: omap: Add larger page NAND chips support
mtd: rawnand: omap: Various style fixes
mtd: rawnand: omap: Check return values
mtd: rawnand: omap: Rename a macro
mtd: rawnand: omap: Aggregate the HW configuration of the ELM
mtd: rawnand: pl353: Add support for the ARM PL353 SMC NAND controller
dt-bindings: mtd: pl353-nand: Describe this hardware controller
MAINTAINERS: Add PL353 NAND controller entry
mtd: rawnand: qcom: avoid writing to obsolete register
mtd: rawnand: marvell: Minor documentation correction
mtd: rawnand: r852: use DEVICE_ATTR_RO() helper macro
mtd: spinand: add SPI-NAND MTD resume handler
mtd: spinand: Add spinand_init_flash() helper
mtd: spinand: add spinand_read_cfg() helper
mtd: rawnand: marvell: add missing clk_disable_unprepare() on error in marvell_nfc_resume()
mtd: rawnand: arasan: Finer grain NV-DDR configuration
mtd: rawnand: arasan: Rename the data interface register
mtd: rawnand: onfi: Fix endianness when reading NV-DDR values
mtd: rawnand: arasan: Use the right DMA mask
...
If a property has an 'items' list, then a 'minItems' or 'maxItems' with the
same size as the list is redundant and can be dropped. Note that is DT
schema specific behavior and not standard json-schema behavior. The tooling
will fixup the final schema adding any unspecified minItems/maxItems.
This condition is partially checked with the meta-schema already, but
only if both 'minItems' and 'maxItems' are equal to the 'items' length.
An improved meta-schema is pending.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # for MMC
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20210615191543.1043414-1-robh@kernel.org
To be fully valid, the NAND controller node in the example should be
named nand-controller instead of flash, should be at the address @0,0
instead of @e1000000 and should have a couple of:
- #address-cells
- #size-cells
properties.
The label is being renamed nfc0 as well which is more usual than nand_0.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210610082040.2075611-8-miquel.raynal@bootlin.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
These nodes are given as examples and are not described nor used
anywhere else. There is also no hardware of my knowledge compatible with
these yet. If we want to be backward compatible, then we should avoid
partially describing nodes and their content while there are no users.
Plus, the examples are wrong (the addresses should be updated) so
let's drop them before converting this file to yaml (only the NAND node,
which will be fixed in the example and described somewhere else is
kept).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210610082040.2075611-7-miquel.raynal@bootlin.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Each chil node should have a reg property, no matter the type of
controller (NAND, NOR, SRAM). This should be part of the bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210610082040.2075611-5-miquel.raynal@bootlin.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
This sentence does not belong to this file as this file describes the
bus on which various controllers are wired to.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210610082040.2075611-4-miquel.raynal@bootlin.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The ranges property is missing in the description while actually used in
the example. This property is actually needed, so mention it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210610082040.2075611-3-miquel.raynal@bootlin.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
- Refactoring powerpc and arm64 kexec DT handling to common code. This
enables IMA on arm64.
- Add kbuild support for applying DT overlays at build time. The first
user are the DT unittests.
- Fix kerneldoc formatting and W=1 warnings in drivers/of/
- Fix handling 64-bit flag on PCI resources
- Bump dtschema version required to v2021.2.1
- Enable undocumented compatible checks for dtbs_check. This allows
tracking of missing binding schemas.
- DT docs improvements. Regroup the DT docs and add the example schema
and DT kernel ABI docs to the doc build.
- Convert Broadcom Bluetooth and video-mux bindings to schema
- Add QCom sm8250 Venus video codec binding schema
- Add vendor prefixes for AESOP, YIC System Co., Ltd, and Siliconfile
Technologies Inc.
- Cleanup of DT schema type references on common properties and
standard unit properties
-----BEGIN PGP SIGNATURE-----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=rF27
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Refactor powerpc and arm64 kexec DT handling to common code. This
enables IMA on arm64.
- Add kbuild support for applying DT overlays at build time. The first
user are the DT unittests.
- Fix kerneldoc formatting and W=1 warnings in drivers/of/
- Fix handling 64-bit flag on PCI resources
- Bump dtschema version required to v2021.2.1
- Enable undocumented compatible checks for dtbs_check. This allows
tracking of missing binding schemas.
- DT docs improvements. Regroup the DT docs and add the example schema
and DT kernel ABI docs to the doc build.
- Convert Broadcom Bluetooth and video-mux bindings to schema
- Add QCom sm8250 Venus video codec binding schema
- Add vendor prefixes for AESOP, YIC System Co., Ltd, and Siliconfile
Technologies Inc.
- Cleanup of DT schema type references on common properties and
standard unit properties
* tag 'devicetree-for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (64 commits)
powerpc: If kexec_build_elf_info() fails return immediately from elf64_load()
powerpc: Free fdt on error in elf64_load()
of: overlay: Fix kerneldoc warning in of_overlay_remove()
of: linux/of.h: fix kernel-doc warnings
of/pci: Add IORESOURCE_MEM_64 to resource flags for 64-bit memory addresses
dt-bindings: bcm4329-fmac: add optional brcm,ccode-map
docs: dt: update writing-schema.rst references
dt-bindings: media: venus: Add sm8250 dt schema
of: base: Fix spelling issue with function param 'prop'
docs: dt: Add DT API documentation
of: Add missing 'Return' section in kerneldoc comments
of: Fix kerneldoc output formatting
docs: dt: Group DT docs into relevant sub-sections
docs: dt: Make 'Devicetree' wording more consistent
docs: dt: writing-schema: Include the example schema in the doc build
docs: dt: writing-schema: Remove spurious indentation
dt-bindings: Fix reference in submitting-patches.rst to the DT ABI doc
dt-bindings: ddr: Add optional manufacturer and revision ID to LPDDR3
dt-bindings: media: video-interfaces: Drop the example
devicetree: bindings: clock: Minor typo fix in the file armada3700-tbg-clock.txt
...
Power domain fits much better than a voltage regulator in regards to
a proper hardware description and from a software perspective as well.
Hence replace the core regulator with the power domain. Note that this
doesn't affect any existing DTBs because we haven't started to use the
regulator yet, and thus, it's okay to change it.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210330230445.26619-4-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Power domain fits much better than a voltage regulator in regards to
a proper hardware description and from a software perspective as well.
Hence replace the core regulator with the power domain. Note that this
doesn't affect any existing DTBs because we haven't started to use the
regulator yet, and thus, it's okay to change it.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210330230445.26619-3-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Power domain fits much better than a voltage regulator in regards to
a proper hardware description and from a software perspective as well.
Hence replace the core regulator with the power domain. Note that this
doesn't affect any existing DTBs because we haven't started to use the
regulator yet, and thus, it's okay to change it.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210330230445.26619-2-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Users of common properties shouldn't have a type definition as the
common schemas already have one. Drop all the unnecessary type
references in the tree.
A meta-schema update to catch these is pending.
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Cheng-Yi Chiang <cychiang@chromium.org>
Cc: Benson Leung <bleung@chromium.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Stefan Wahren <wahrenst@gmx.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Odelu Kukatla <okukatla@codeaurora.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-remoteproc@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Dmity Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Suman Anna <s-anna@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20210316194858.3527845-1-robh@kernel.org
- Sync dtc to upstream version v1.6.0-51-g183df9e9c2b9 and build
host fdtoverlay
- Add kbuild support to build DT overlays (%.dtbo)
- Drop NULLifying match table in of_match_device(). In preparation for
this, there are several driver cleanups to use
(of_)?device_get_match_data().
- Drop pointless wrappers from DT struct device API
- Convert USB binding schemas to use graph schema and remove old plain
text graph binding doc
- Convert spi-nor and v3d GPU bindings to DT schema
- Tree wide schema fixes for if/then schemas, array size constraints,
and undocumented compatible strings in examples
- Handle 'no-map' correctly for already reserved memblock regions
-----BEGIN PGP SIGNATURE-----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=9V4A
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Sync dtc to upstream version v1.6.0-51-g183df9e9c2b9 and build host
fdtoverlay
- Add kbuild support to build DT overlays (%.dtbo)
- Drop NULLifying match table in of_match_device().
In preparation for this, there are several driver cleanups to use
(of_)?device_get_match_data().
- Drop pointless wrappers from DT struct device API
- Convert USB binding schemas to use graph schema and remove old plain
text graph binding doc
- Convert spi-nor and v3d GPU bindings to DT schema
- Tree wide schema fixes for if/then schemas, array size constraints,
and undocumented compatible strings in examples
- Handle 'no-map' correctly for already reserved memblock regions
* tag 'devicetree-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
driver core: platform: Drop of_device_node_put() wrapper
of: Remove of_dev_{get,put}()
dt-bindings: usb: Change descibe to describe in usbmisc-imx.txt
dt-bindings: can: rcar_canfd: Group tuples in pin control properties
dt-bindings: power: renesas,apmu: Group tuples in cpus properties
dt-bindings: mtd: spi-nor: Convert to DT schema format
dt-bindings: Use portable sort for version cmp
dt-bindings: ethernet-controller: fix fixed-link specification
dt-bindings: irqchip: Add node name to PRUSS INTC
dt-bindings: interconnect: Fix the expected number of cells
dt-bindings: Fix errors in 'if' schemas
dt-bindings: iommu: renesas,ipmmu-vmsa: Make 'power-domains' conditionally required
dt-bindings: Fix undocumented compatible strings in examples
kbuild: Add support to build overlays (%.dtbo)
scripts: dtc: Remove the unused fdtdump.c file
scripts: dtc: Build fdtoverlay tool
scripts/dtc: Update to upstream version v1.6.0-51-g183df9e9c2b9
scripts: dtc: Fetch fdtoverlay.c from external DTC project
dt-bindings: thermal: sun8i: Fix misplaced schema keyword in compatible strings
dt-bindings: iio: dac: Fix AD5686 references
...
DT properties which can have multiple entries need to specify what the
entries are and define how many entries there can be. In the case of
only a single entry, just 'maxItems: 1' is sufficient.
Add the missing entry constraints. These were found with a modified
meta-schema. Unfortunately, there are a few cases where the size
constraints are not defined such as common bindings, so the meta-schema
can't be part of the normal checks.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for-iio
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210104230253.2805217-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
The RZ/G2 Series has the RPC-IF interface. Update bindings to support:
r8a774a1, r8a774b1, r8a774c0, and r8a774e1
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20210102115412.3402059-1-aford173@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Memory controller drivers for v5.11 - Tegra SoC, part two
Continuation of work on Tegra SoC memory controllers towards adding
interconnect support and integration with devfreq.
This brings few more patches including one which removes/fixes annoying
warning if the DTS patches get applied. This is expected and only
informs that new features of Tegra memory controller drivers will not be
enabled however the warning itself could look worrying.
* tag 'memory-controller-drv-tegra-5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
memory: tegra30: Support interconnect framework
memory: tegra20: Support hardware versioning and clean up OPP table initialization
dt-bindings: memory: tegra20-emc: Document opp-supported-hw property
Link: https://lore.kernel.org/r/20201207075758.5501-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Document opp-supported-hw property, which is not strictly necessary to
have on Tegra20, but it's very convenient to have because all other SoC
core devices will use hardware versioning, and thus, it's good to maintain
the consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20201203192439.16177-2-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
There is a bigger work from Dmitry Osipenko around Tegra SoC memory
controller drivers, mostly towards adding interconnect support and
integration with devfreq. This work touches all Tegra memory controller
drivers and also few other SoC-related parts. It's not yet finished but
the intermediate stage seems ready to merge.
Beside that Tegra 210 memory controller got few fixes and received new
swgroups (work of Nicolin Chen).
-----BEGIN PGP SIGNATURE-----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=EUPM
-----END PGP SIGNATURE-----
Merge tag 'memory-controller-drv-tegra-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/drivers
Memory controller drivers for v5.11 - Tegra SoC
There is a bigger work from Dmitry Osipenko around Tegra SoC memory
controller drivers, mostly towards adding interconnect support and
integration with devfreq. This work touches all Tegra memory controller
drivers and also few other SoC-related parts. It's not yet finished but
the intermediate stage seems ready to merge.
Beside that Tegra 210 memory controller got few fixes and received new
swgroups (work of Nicolin Chen).
* tag 'memory-controller-drv-tegra-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl: (38 commits)
memory: tegra30-emc: Remove unnecessary of_node_put in tegra_emc_probe
memory: tegra: Complete tegra210_swgroups
memory: tegra30-emc: Continue probing if timings are missing in device-tree
memory: tegra30-emc: Make driver modular
memory: tegra30: Add FIFO sizes to memory clients
memory: tegra20-emc: Add devfreq support
memory: tegra20-emc: Remove IRQ number from error message
memory: tegra20-emc: Factor out clk initialization
memory: tegra20-emc: Use dev_pm_opp_set_clkname()
memory: tegra: Correct stub of devm_tegra_memory_controller_get()
memory: tegra20: Support interconnect framework
memory: tegra20-emc: Continue probing if timings are missing in device-tree
memory: tegra20-emc: Make driver modular
memory: tegra-mc: Add interconnect framework
memory: tegra: Add missing latency allowness entry for Page Table Cache
memory: tegra: Remove superfluous error messages around platform_get_irq()
memory: tegra: Use devm_platform_ioremap_resource()
memory: tegra: Add and use devm_tegra_memory_controller_get()
dt-bindings: host1x: Document new interconnect properties
dt-bindings: tegra30-actmon: Document OPP and interconnect properties
...
Link: https://lore.kernel.org/r/20201126191241.23302-1-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Document new OPP table and voltage regulator properties which are needed
for supporting dynamic voltage-frequency scaling of the memory controller.
Some boards may have a fixed core voltage regulator, hence it's optional
because frequency scaling still may be desired.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201104164923.21238-15-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
External memory controller is interconnected with memory controller and
with external memory. Document new interconnect property which turns
External Memory Controller into interconnect provider.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201104164923.21238-14-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Memory controller is interconnected with memory clients and with the
External Memory Controller. Document new interconnect property which
turns memory controller into interconnect provider.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201104164923.21238-13-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Document new OPP table and voltage regulator properties which are needed
for supporting dynamic voltage-frequency scaling of the memory controller.
Some boards may have a fixed core voltage regulator, hence it's optional
because frequency scaling still may be desired.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201104164923.21238-12-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
External memory controller is interconnected with memory controller and
with external memory. Document new interconnect property which turns
External Memory Controller into interconnect provider.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201104164923.21238-11-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Memory controller is interconnected with memory clients and with the
External Memory Controller. Document new interconnect property which
turns memory controller into interconnect provider.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201104164923.21238-10-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The SoC core voltage can't be changed without taking into account the
clock rate of External Memory Controller. Document OPP table that will
be used for dynamic voltage frequency scaling, taking into account EMC
voltage requirement. Document optional core voltage regulator, which is
optional because some boards may have a fixed core regulator and still
frequency scaling may be desired to have.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201104164923.21238-9-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
External Memory Controller is interconnected with memory controller and
with external memory. Document new interconnect property which turns EMC
into interconnect provider.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201104164923.21238-8-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Memory controller is interconnected with memory clients and with the
External Memory Controller. Document new interconnect property which
turns memory controller into interconnect provider.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201104164923.21238-7-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tegra20 External Memory Controller talks to DRAM chips and it needs to be
reprogrammed when memory frequency changes. Tegra Memory Controller sits
behind EMC and these controllers are tightly coupled. This patch adds the
new phandle property which allows to properly express connection of EMC
and MC hardware in a device-tree, it also put the Tegra20 EMC binding on
par with Tegra30+ EMC bindings, which is handy to have.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201104164923.21238-6-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
There is superfluous zero in the registers base address and registers
size should be twice bigger.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20201104164923.21238-5-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Various driver updates for platforms. A bulk of this is smaller fixes or
cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs
and platforms.
-----BEGIN PGP SIGNATURE-----
iQJDBAABCgAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl+TUboPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3T4YP/R5pjF2C1gt8FrCaG4IfhIY1VHWelfPcB5qB
RC7Pn4MCRCEY+10YPXA70oS6KBaC+gtZ4bPeInzfLXh1ynFJJb+XtAIxoRhnkEw+
/R979wNcIls9JqkvnHWFx29Y008W2ZNcXVNKH7O2Gxy+eKzDcTMsoH/zj8xWrV5b
+eBllTzGU4RArYRJdcwOBQwMO6L2pzADHZ7hGMAY//8fo+qrxg8b9EINsH1UHCa8
gQdWdVlmv6GeLB6RYLRBCWxpW4jOLDqEAvyDV84QQmYHvzD9tqJExNR0hfGTs4TU
TZWK7LWSNqF0ujQUbFh9Ikcx6DypU1gvE7LKhCDrf4D7HLRX5v4BjGH+xtVtjsyD
xzh4WEoa3qCNu1mxQjKG8Y6U7bB9cRI2TPVxbbmI4ZuF0njvybecwwOZUBQl4aD4
5x+Df3pO/E5ECLOBeTnLgvw20fcjHv4HP8l63B6ADb31FUiZrJXItvayY5qXWe+P
HSgUykmVA4nd4PnLsSj9seyWqOTIqUZ3U3TsmfxIQh2Otie01okwuHb1J7ErO/u0
W148SgSwVbnkPxjbBHKGgC2r+Q/AjSDGRBYL0ThIVFUztxTBBwhj3FIvMnyyxTIj
yFBY14KQ8FcNUs8DrbPCaAx/RDCB02IHdvvIlyTmU3RBq7UhJVIglpLzzo2ed9F2
5u/aVH3y
=tfPb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms. A bulk of this is smaller fixes
or cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs and
platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
drm/mediatek: reduce clear event
soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
soc: mediatek: cmdq: add jump function
soc: mediatek: cmdq: add write_s_mask value function
soc: mediatek: cmdq: add write_s value function
soc: mediatek: cmdq: add read_s function
soc: mediatek: cmdq: add write_s_mask function
soc: mediatek: cmdq: add write_s function
soc: mediatek: cmdq: add address shift in jump
soc: mediatek: mtk-infracfg: Fix kerneldoc
soc: amlogic: pm-domains: use always-on flag
reset: sti: reset-syscfg: fix struct description warnings
reset: imx7: add the cm4 reset for i.MX8MQ
dt-bindings: reset: imx8mq: add m4 reset
reset: Fix and extend kerneldoc
reset: reset-zynqmp: Added support for Versal platform
dt-bindings: reset: Updated binding for Versal reset driver
reset: imx7: Support module build
soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
soc: fsl: qman: convert to use be32_add_cpu()
...
This doesn't yet do anything in the tools, but make it explicit so we can
check either 'unevaluatedProperties' or 'additionalProperties' is present
in schemas.
'unevaluatedProperties' is appropriate when including another schema (via
'$ref') and all possible properties and/or child nodes are not
explicitly listed in the schema with the '$ref'.
This is in preparation to add a meta-schema to check for missing
'unevaluatedProperties' or 'additionalProperties'. This has been a
constant source of review issues.
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20201005183830.486085-2-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Including:
- Removal of the dev->archdata.iommu (or similar) pointers from
most architectures. Only Sparc is left, but this is private to
Sparc as their drivers don't use the IOMMU-API.
- ARM-SMMU Updates from Will Deacon:
- Support for SMMU-500 implementation in Marvell
Armada-AP806 SoC
- Support for SMMU-500 implementation in NVIDIA Tegra194 SoC
- DT compatible string updates
- Remove unused IOMMU_SYS_CACHE_ONLY flag
- Move ARM-SMMU drivers into their own subdirectory
- Intel VT-d Updates from Lu Baolu:
- Misc tweaks and fixes for vSVA
- Report/response page request events
- Cleanups
- Move the Kconfig and Makefile bits for the AMD and Intel
drivers into their respective subdirectory.
- MT6779 IOMMU Support
- Support for new chipsets in the Renesas IOMMU driver
- Other misc cleanups and fixes (e.g. to improve compile test
coverage)
-----BEGIN PGP SIGNATURE-----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=3O2Z
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Remove of the dev->archdata.iommu (or similar) pointers from most
architectures. Only Sparc is left, but this is private to Sparc as
their drivers don't use the IOMMU-API.
- ARM-SMMU updates from Will Deacon:
- Support for SMMU-500 implementation in Marvell Armada-AP806 SoC
- Support for SMMU-500 implementation in NVIDIA Tegra194 SoC
- DT compatible string updates
- Remove unused IOMMU_SYS_CACHE_ONLY flag
- Move ARM-SMMU drivers into their own subdirectory
- Intel VT-d updates from Lu Baolu:
- Misc tweaks and fixes for vSVA
- Report/response page request events
- Cleanups
- Move the Kconfig and Makefile bits for the AMD and Intel drivers into
their respective subdirectory.
- MT6779 IOMMU Support
- Support for new chipsets in the Renesas IOMMU driver
- Other misc cleanups and fixes (e.g. to improve compile test coverage)
* tag 'iommu-updates-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (77 commits)
iommu/amd: Move Kconfig and Makefile bits down into amd directory
iommu/vt-d: Move Kconfig and Makefile bits down into intel directory
iommu/arm-smmu: Move Arm SMMU drivers into their own subdirectory
iommu/vt-d: Skip TE disabling on quirky gfx dedicated iommu
iommu: Add gfp parameter to io_pgtable_ops->map()
iommu: Mark __iommu_map_sg() as static
iommu/vt-d: Rename intel-pasid.h to pasid.h
iommu/vt-d: Add page response ops support
iommu/vt-d: Report page request faults for guest SVA
iommu/vt-d: Add a helper to get svm and sdev for pasid
iommu/vt-d: Refactor device_to_iommu() helper
iommu/vt-d: Disable multiple GPASID-dev bind
iommu/vt-d: Warn on out-of-range invalidation address
iommu/vt-d: Fix devTLB flush for vSVA
iommu/vt-d: Handle non-page aligned address
iommu/vt-d: Fix PASID devTLB invalidation
iommu/vt-d: Remove global page support in devTLB flush
iommu/vt-d: Enforce PASID devTLB field mask
iommu: Make some functions static
iommu/amd: Remove double zero check
...
* Spelling
* http to https updates
NAND core changes:
* Drop useless 'depends on' in Kconfig
* Add an extra level in the Kconfig hierarchy
* Trivial spellings
* Dynamic allocation of the interface configurations
* Dropping the default ONFI timing mode
* Various cleanup (types, structures, naming, comments)
* Hide the chip->data_interface indirection
* Add the generic rb-gpios property
* Add the ->choose_interface_config() hook
* Introduce nand_choose_best_sdr_timings()
* Use default values for tPROG_max and tBERS_max
* Avoid redefining tR_max and tCCS_min
* Add a helper to find the closest ONFI mode
* bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
* fsl-upm: Deprecation of specific DT properties
* fsl_upm: Driver rework and cleanup in favor of ->exec_op()
* Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
* brcmnand: ECC error handling on EDU transfers
* brcmnand: Don't default to EDU transfers
* qcom: Set BAM mode only if not set already
* qcom: Avoid write to unavailable register
* gpio: Driver rework in favor of ->exec_op()
* tango: ->exec_op() conversion
* mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
* toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
* toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
* toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
* hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
SPI NOR core changes:
* Disable Quad Mode in spi_nor_restore().
* Don't abort BFPT parsing when QER reserved value is used.
* Add support/update capabilities for few flashes.
* Drop s70fl01gs flash: it does not support RDSR(05h) which
is critical for erase/write.
* Merge the SPIMEM DTR bits in spi-nor/next to avoid conflicts
during the release cycle.
SPI NOR controller drivers changes:
* Move the cadence-quadspi driver to spi-mem. The series was
taken through the SPI tree. Merge it also in spi-nor/next
to avoid conflicts during the release cycle.
* intel-spi:
- Add new PCI IDs.
- Ignore the Write Disable command, the controller doesn't
support it.
- Fix performance regression.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl8vJtMACgkQJWrqGEe9
VoRdGAf/Y5m5BwmLilkEYpffyxi7dVR6XOKPLU5EJXkS3dPvH9398zchbHOdedCZ
OzJIfh6Iv+qbkgS2g0lAAT+SAfOfG9plubvSdkjrHXl4eZXRnR/49RF5LAEju7sz
Uw1HdRcawyEi5uI9yYS0tCeVMIUJq+5x7VibH+82yOIdSPc60c7FDc5ih/nVKj/a
Pn9LOzGzkdndcE1b3FcF2Uk/T1YOJx3Yt5ngALlPpJxaDZmQSHtYPuuz8DfUbamf
uj3CkpqYRyT18CzuFvtuba6LyF+donXNJgvl6ivW7dlRSPzSMnDQu7J5bpNhUfcd
p/ZdzX1Jxle4theDm0J9ALsSSM5g2w==
=RiY8
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD core changes:
- Spelling
- http to https updates
NAND core changes:
- Drop useless 'depends on' in Kconfig
- Add an extra level in the Kconfig hierarchy
- Trivial spellings
- Dynamic allocation of the interface configurations
- Dropping the default ONFI timing mode
- Various cleanup (types, structures, naming, comments)
- Hide the chip->data_interface indirection
- Add the generic rb-gpios property
- Add the ->choose_interface_config() hook
- Introduce nand_choose_best_sdr_timings()
- Use default values for tPROG_max and tBERS_max
- Avoid redefining tR_max and tCCS_min
- Add a helper to find the closest ONFI mode
- bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
- fsl-upm: Deprecation of specific DT properties
- fsl_upm: Driver rework and cleanup in favor of ->exec_op()
- Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
- brcmnand: ECC error handling on EDU transfers
- brcmnand: Don't default to EDU transfers
- qcom: Set BAM mode only if not set already
- qcom: Avoid write to unavailable register
- gpio: Driver rework in favor of ->exec_op()
- tango: ->exec_op() conversion
- mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
- toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4,
TC58NVG0S3E, and TC58TEG5DCLTA00
- hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
SPI NOR core changes:
- Disable Quad Mode in spi_nor_restore().
- Don't abort BFPT parsing when QER reserved value is used.
- Add support/update capabilities for few flashes.
- Drop s70fl01gs flash: it does not support RDSR(05h) which is
critical for erase/write.
- Merge the SPIMEM DTR bits in spi-nor/next to avoid conflicts during
the release cycle.
SPI NOR controller drivers changes:
- Move the cadence-quadspi driver to spi-mem. The series was taken
through the SPI tree. Merge it also in spi-nor/next to avoid
conflicts during the release cycle.
- intel-spi:
- Add new PCI IDs.
- Ignore the Write Disable command, the controller doesn't support
it.
- Fix performance regression"
* tag 'mtd/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (79 commits)
MTD: pfow.h: drop a duplicated word
MTD: mtd-abi.h: drop a duplicated word
mtd: rawnand: omap_elm: Replace HTTP links with HTTPS ones
mtd: Replace HTTP links with HTTPS ones
mtd: hyperbus: Replace HTTP links with HTTPS ones
mtd: revert "spi-nor: intel: provide a range for poll_timout"
mtd: spi-nor: update read capabilities for w25q64 and s25fl064k
mtd: spi-nor: micron: Add SPI_NOR_DUAL_READ flag on mt25qu02g
mtd: spi-nor: macronix: Add support for mx66u2g45g
mtd: spi-nor: intel-spi: Simulate WRDI command
mtd: spi-nor: Disable the flash quad mode in spi_nor_restore()
mtd: spi-nor: Add capability to disable flash quad mode
mtd: spi-nor: spansion: Remove s70fl01gs from flash_info
mtd: spi-nor: sfdp: do not make invalid quad enable fatal
dt-bindings: mtd: fsl-upm-nand: Deprecate chip-delay and fsl, upm-wait-flags
mtd: rawnand: stm32_fmc2: get resources from parent node
mtd: rawnand: stm32_fmc2: use regmap APIs
memory: stm32-fmc2-ebi: add STM32 FMC2 EBI controller driver
dt-bindings: memory-controller: add STM32 FMC2 EBI controller documentation
dt-bindings: mtd: update STM32 FMC2 NAND controller documentation
...
- Improve device links cycle detection and breaking. Add more
bindings for device link dependencies.
- Refactor parsing 'no-map' in __reserved_mem_alloc_size()
- Improve DT unittest 'ranges' and 'dma-ranges' test case to check
differing cell sizes
- Various http to https link conversions
- Add a schema check to prevent 'syscon' from being used by itself
without a more specific compatible
- A bunch more DT binding conversions to schema
-----BEGIN PGP SIGNATURE-----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=6f3o
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- Improve device links cycle detection and breaking. Add more bindings
for device link dependencies.
- Refactor parsing 'no-map' in __reserved_mem_alloc_size()
- Improve DT unittest 'ranges' and 'dma-ranges' test case to check
differing cell sizes
- Various http to https link conversions
- Add a schema check to prevent 'syscon' from being used by itself
without a more specific compatible
- A bunch more DT binding conversions to schema
* tag 'devicetree-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
of: reserved-memory: remove duplicated call to of_get_flat_dt_prop() for no-map node
of: unittest: Use bigger address cells to catch parser regressions
dt-bindings: memory-controllers: Convert mmdc to json-schema
dt-bindings: mtd: Convert imx nand to json-schema
dt-bindings: mtd: Convert gpmi nand to json-schema
dt-bindings: iio: io-channel-mux: Fix compatible string in example code
of: property: Add device link support for pinctrl-0 through pinctrl-8
of: property: Add device link support for multiple DT bindings
dt-bindings: phy: ti: phy-gmii-sel: convert bindings to json-schema
dt-bindings: mux: mux.h: drop a duplicated word
dt-bindings: misc: Convert olpc,xo1.75-ec to json-schema
dt-bindings: aspeed-lpc: Replace HTTP links with HTTPS ones
dt-bindings: drm/bridge: Replace HTTP links with HTTPS ones
drm/tilcdc: Replace HTTP links with HTTPS ones
dt-bindings: iommu: renesas,ipmmu-vmsa: Add r8a774e1 support
dt-bindings: fpga: Replace HTTP links with HTTPS ones
dt-bindings: virtio: Replace HTTP links with HTTPS ones
dt-bindings: media: imx274: Add optional input clock and supplies
dt-bindings: i2c-gpio: Use 'deprecated' keyword on deprecated properties
dt-bindings: interrupt-controller: Fix typos in loongson,liointc.yaml
...
This patch add description for MT6779 SMI.
There are GALS in smi-larb but without clock of GALS alone.
changelog since v2:
Add GALS for mt6779 in smi-common.txt
Signed-off-by: Ming-Fan Chen <ming-fan.chen@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1578465691-30692-3-git-send-email-ming-fan.chen@mediatek.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Renesas Reduced Pin Count Interface (RPC-IF) allows a SPI flash or
HyperFlash connected to the SoC to be accessed via the external address
space read mode or the manual mode.
Document the device tree bindings for the Renesas RPC-IF found in the R-Car
gen3 SoCs.
Based on the original patch by Mason Yang <masonccyang@mxic.com.tw>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Link: https://lore.kernel.org/r/54a84c75-fa17-9976-d9a6-a69ef67c418b@cogentembedded.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Another round of 'allOf' removals that came in this cycle.
json-schema versions draft7 and earlier have a weird behavior in that
any keywords combined with a '$ref' are ignored (silently). The correct
form was to put a '$ref' under an 'allOf'. This behavior is now changed
in the 2019-09 json-schema spec and '$ref' can be mixed with other
keywords. The json-schema library doesn't yet support this, but the
tooling now does a fixup for this and either way works.
This has been a constant source of review comments, so let's change this
treewide so everyone copies the simpler syntax.
Signed-off-by: Rob Herring <robh@kernel.org>
- Convert various DT (non-binding) doc files to ReST
- Various improvements to device link code
- Fix __of_attach_node_sysfs refcounting bug
- Add support for 'memory-region-names' with reserved-memory binding
- Vendor prefixes for Protonic Holland, BeagleBoard.org, Alps, Check
Point, Würth Elektronik, U-Boot, Vaisala, Baikal Electronics, Shanghai
Awinic Technology Co., MikroTik, Silex Insight
- A bunch more binding conversions to DT schema. Only 3K to go.
- Add a minimum version check for schema tools
- Treewide dropping of 'allOf' usage with schema references. Not needed
in new json-schema spec.
- Some formatting clean-ups of schemas
-----BEGIN PGP SIGNATURE-----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=/MDi
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Convert various DT (non-binding) doc files to ReST
- Various improvements to device link code
- Fix __of_attach_node_sysfs refcounting bug
- Add support for 'memory-region-names' with reserved-memory binding
- Vendor prefixes for Protonic Holland, BeagleBoard.org, Alps, Check
Point, Würth Elektronik, U-Boot, Vaisala, Baikal Electronics,
Shanghai Awinic Technology Co., MikroTik, Silex Insight
- A bunch more binding conversions to DT schema. Only 3K to go.
- Add a minimum version check for schema tools
- Treewide dropping of 'allOf' usage with schema references. Not needed
in new json-schema spec.
- Some formatting clean-ups of schemas
* tag 'devicetree-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (194 commits)
dt-bindings: clock: Add documentation for X1830 bindings.
dt-bindings: mailbox: Convert imx mu to json-schema
dt-bindings: power: Convert imx gpcv2 to json-schema
dt-bindings: power: Convert imx gpc to json-schema
dt-bindings: Merge gpio-usb-b-connector with usb-connector
dt-bindings: timer: renesas: cmt: Convert to json-schema
dt-bindings: clock: Convert i.MX8QXP LPCG to json-schema
dt-bindings: timer: Convert i.MX GPT to json-schema
dt-bindings: thermal: rcar-thermal: Add device tree support for r8a7742
dt-bindings: serial: Add binding for UART pin swap
dt-bindings: geni-se: Add interconnect binding for GENI QUP
dt-bindings: geni-se: Convert QUP geni-se bindings to YAML
dt-bindings: vendor-prefixes: Add Silex Insight vendor prefix
dt-bindings: input: touchscreen: edt-ft5x06: change reg property
dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver
dt-bindings: timer: renesas: mtu2: Convert to json-schema
of/fdt: Remove redundant kbasename function call
dt-bindings: clock: Convert i.MX1 clock to json-schema
dt-bindings: clock: Convert i.MX21 clock to json-schema
dt-bindings: clock: Convert i.MX25 clock to json-schema
...
Convert the ingenic,jz4780-nemc.txt doc file to ingenic,nemc.yaml.
The ingenic,jz4725b-nemc compatible string was added in the process,
with a fallback to ingenic,jz4740-nemc.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the Renesas DDR Bus Controller Device Tree binding documentation
to json-schema.
Drop referrals to driver behavior.
Make power-domains required, as it is present for all current users.
Update the example to match reality.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
These are mainly fixups for comments that collided with me
already merging v3 of the series, and one patch that I had forgotten
to pick up.
* baikal/drivers:
bus: bt1-axi: Build the driver into the kernel
bus: bt1-apb: Build the driver into the kernel
bus: bt1-axi: Use sysfs_streq instead of strncmp
bus: bt1-axi: Optimize the return points in the driver
bus: bt1-apb: Use sysfs_streq instead of strncmp
bus: bt1-apb: Use PTR_ERR_OR_ZERO to return from request-regs method
bus: bt1-apb: Fix show/store callback identations
bus: bt1-apb: Include linux/io.h
dt-bindings: memory: Add Baikal-T1 L2-cache Control Block binding
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is a single register provided by the SoC system controller,
which can be used to tune the L2-cache RAM up. It only provides a way
to change the L2-RAM access latencies. So aside from "be,bt1-l2-ctl"
compatible string the device node can be optionally equipped with the
properties of Tag/Data/WS latencies.
Link: https://lore.kernel.org/r/20200526125928.17096-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: linux-mips@vger.kernel.org
Cc: soc@kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This contains a V4L2 video capture driver for Tegra210.
-----BEGIN PGP SIGNATURE-----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=ZA0j
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.8-media' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
media: tegra: Changes for v5.8-rc1
This contains a V4L2 video capture driver for Tegra210.
* tag 'tegra-for-5.8-media' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
media: tegra-video: Do not enable COMPILE_TEST
MAINTAINERS: correct path in TEGRA VIDEO DRIVER
media: tegra-video: Make tegra210_video_formats static
MAINTAINERS: Add Tegra Video driver section
media: tegra-video: Add Tegra210 Video input driver
dt-bindings: i2c: tegra: Document Tegra210 VI I2C
dt-bindings: tegra: Add VI and CSI bindings
dt-bindings: cpufreq: Add binding for NVIDIA Tegra20/30
dt-bindings: memory: tegra: Add external memory controller binding for Tegra210
dt-bindings: clock: tegra: Remove PMC clock IDs
dt-bindings: clock: tegra: Add clock ID for CSI TPG clock
Link: https://lore.kernel.org/r/20200515145311.1580134-7-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The examples template is a 'simple-bus' with a size of 1 cell for
had between 2 and 4 cells which really only errors on I2C or SPI type
devices with a single cell.
The easiest fix in most cases is to change the 'reg' property to for 1 cell
address and size. In some cases with child devices having 2 cells, that
doesn't make sense so a bus node is needed.
Acked-by: Stephen Boyd <sboyd@kernel.org> # clk
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
Add the binding document for the external memory controller (EMC) which
communicates with external LPDDR4 devices. It includes the bindings of
the EMC node and a sub-node of EMC table which under the reserved memory
node. The EMC table contains the data of the rates that EMC supported.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Convert the Calxeda DDR memory controller binding to DT schema format
using json-schema.
Although this technically covers the whole DRAM controller, the
intention to use it only for error reporting and mapping fault addresses
to DRAM chips.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
json-schema versions draft7 and earlier have a weird behavior in that
any keywords combined with a '$ref' are ignored (silently). The correct
form was to put a '$ref' under an 'allOf'. This behavior is now changed
in the 2019-09 json-schema spec and '$ref' can be mixed with other
keywords. The json-schema library doesn't yet support this, but the
tooling now does a fixup for this and either way works.
This has been a constant source of review comments, so let's change this
treewide so everyone copies the simpler syntax.
Scripted with ruamel.yaml with some manual fixups. Some minor whitespace
changes from the script.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for I2C
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for-iio
Reviewed-by: Stephen Boyd <sboyd@kernel.org> # clock
Signed-off-by: Rob Herring <robh@kernel.org>
Fix various inconsistencies in schema indentation. Most of these are
list indentation which should be 2 spaces more than the start of the
enclosing keyword. This doesn't matter functionally, but affects running
scripts which do transforms on the schema files.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add the binding document for the external memory controller (EMC) which
communicates with external LPDDR4 devices. It includes the bindings of
the EMC node and a sub-node of EMC table which under the reserved memory
node. The EMC table contains the data of the rates that EMC supported.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
'reg-io-width' property is an enum so there is no need to specify its
type.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
A recent update to dtc and changes to the default warnings introduced
some new warnings in the DT binding examples:
Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.example.dts:23.13-61:
Warning (dma_ranges_format): /example-0/dram-controller@1c01000:dma-ranges: "dma-ranges" property has invalid length (12 bytes) (parent #address-cells == 1, child #address-cells == 2, #size-cells == 1)
Documentation/devicetree/bindings/hwmon/adi,axi-fan-control.example.dts:17.22-28.11:
Warning (unit_address_vs_reg): /example-0/fpga-axi@0: node has a unit name, but no reg or ranges property
Documentation/devicetree/bindings/memory-controllers/nvidia,tegra186-mc.example.dts:34.13-54:
Warning (dma_ranges_format): /example-0/memory-controller@2c00000:dma-ranges: "dma-ranges" property has invalid length (24 bytes) (parent #address-cells == 1, child #address-cells == 2, #size-cells == 2)
Documentation/devicetree/bindings/mfd/st,stpmic1.example.dts:19.15-79.11:
Warning (unit_address_vs_reg): /example-0/i2c@0: node has a unit name, but no reg or ranges property
Documentation/devicetree/bindings/net/qcom,ipq8064-mdio.example.dts:28.23-31.15:
Warning (unit_address_vs_reg): /example-0/mdio@37000000/switch@10: node has a unit name, but no reg or ranges property
Documentation/devicetree/bindings/rng/brcm,bcm2835.example.dts:17.5-21.11:
Warning (unit_address_vs_reg): /example-0/rng: node has a reg or ranges property, but no unit name
Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.example.dts:20.20-43.11:
Warning (unit_address_vs_reg): /example-0/soc@0: node has a unit name, but no reg or ranges property
Documentation/devicetree/bindings/usb/ingenic,musb.example.dts:18.28-21.11:
Warning (unit_address_vs_reg): /example-0/usb-phy@0: node has a unit name, but no reg or ranges property
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: "Nuno Sá" <nuno.sa@analog.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-hwmon@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-arm-msm@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-crypto@vger.kernel.org
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-spi@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Several DT references got broken due to txt->yaml conversion.
Those are auto-fixed by running:
scripts/documentation-file-ref-check --fix
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The example in the Tegra124 EMC device tree binding looks like an old
version that doesn't contain all the required fields. Update it with a
version from the current DTS files to fix the make dt_binding_check
target.
Reported-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
[robh: also fix missing '#reset-cells']
Signed-off-by: Rob Herring <robh@kernel.org>
This contains a conversion of the Tegra124 EMC bindings to json-schema
as well as the addition of the bindings for the memory subsystem found
on Tegra186 and Tegra194.
-----BEGIN PGP SIGNATURE-----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=iPZ2
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.6-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
dt-bindings: Changes for v5.6-rc1
This contains a conversion of the Tegra124 EMC bindings to json-schema
as well as the addition of the bindings for the memory subsystem found
on Tegra186 and Tegra194.
* tag 'tegra-for-5.6-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: memory: Add Tegra186 memory subsystem
dt-bindings: memory: Add Tegra194 memory controller header
dt-bindings: memory: Add Tegra186 memory client IDs
dt-bindings: memory-controller: Convert Tegra124 EMC to json-schema
Link: https://lore.kernel.org/r/20200111003553.2411874-1-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
The NVIDIA Tegra186 SoC contains a memory subsystem composed of the
memory controller and the external memory controller. The memory
controller provides interfaces for the memory clients to access the
memory. Accesses can be either bounced through the SMMU for IOVA
translation or directly to the EMC.
The bulk of the programming of the external memory controller happens
through interfaces exposed by the BPMP. Describe this relationship by
adding a phandle reference to the BPMP to the EMC node.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Convert the device tree bindings for the Tegra124 EMC controller to the
DT schema format using json-schema. While at it, clean up the binding a
little bit by removing any mention of how RAM code and clock frequency
are represented in unit-addresses (which they aren't) and by adding the
EMC clock without which the EMC controller can't change the frequency at
which the external memory is clocked. While this is technically an ABI
break (the clock was not required before), this should be fine because
there isn't much that the EMC driver can do without access to the EMC
clock.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Add devicetree bindings for the i.MX DDR Controller on imx8m series
chips. It supports dynamic frequency switching between multiple data
rates and this is exposed to Linux via the devfreq subsystem.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Json-schema requires a $ref to be under an 'allOf' if there are
additional constraints otherwise the additional constraints are
ignored. (Note that this behavior will be changed in draft8.)
Fixes: 641262f5e1 ("dt-bindings: memory: Add binding for NVIDIA Tegra30 External Memory Controller")
Fixes: 785685b7a1 ("dt-bindings: memory: Add binding for NVIDIA Tegra30 Memory Controller")
Fixes: 8da65c377b ("dt-bindings: memory: tegra30: Convert to Tegra124 YAML")
Cc: Thierry Reding <treding@nvidia.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This contains various updates to device tree bindings and includes that
are related to driver changes in other Tegra branches.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAl29jNkTHHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zoSciD/41eSVm8Y++rU95KB+XpmrYQTeRqP9F
XLIrrY4sUgDpPwDgfIM/Fmyy2uIl7UtnsMDhBWkwfSkgWJGw083Tim0/eFZBTvGw
j+z99xFivav2QjtK0XZp6xfKXWlWpWwQTOW7DKsq22LYiH+7bp1zMbFoy/RkCg/O
klX16iwTZs69ym/0UDNj/qB6+MybOFxUffaIvo5cLXq9Us8XSOv7SCiH0TIDXk8f
KcqvU5R1nzrrG15Cbxlg/2kkS1QvGSsYj2LC8n6s9dzsMK4Gp3D9DVVr+8W2xbv3
rVGAXffSu+BpzaAKbLGCojJ+lAvA7au9Q9Vm+gtq+QdbzjRgx49/EK0Ys7nC5Pll
Txe38oKePEkzTrdD0Y0r5SztRORSGCED4WmgroThomTgX6r/vltEYGxYvIt2/L/F
chgcBT4t82tlBf3JvD0YpoH40nmF6vWPnPVmDDIcrXDCBigmEjbztXV0tgBibaDl
RuC0BpOGS7bKH9lSlfcRrQRzqnOQXrQoMeRa2/Mv6b6EAG9BZ4+rqaAlGuO1BmsC
zSP+loJ96fdTHNWnjN+JHlZy5uVYCCwx/QaF/sVQ2LMiscq9y9QA7kW4p4To2r0r
+45nF5CD+gft2fnBK1OmaAiDeFe4/XdMQBOJ+SlDDehWLBhN2xtzJl6UGYlGZOZ5
+QNEeVifuL41+Q==
=LlnG
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.5-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
dt-bindings: Changes for v5.5-rc1
This contains various updates to device tree bindings and includes that
are related to driver changes in other Tegra branches.
* tag 'tegra-for-5.5-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: memory: Add binding for NVIDIA Tegra30 External Memory Controller
dt-bindings: memory: Add binding for NVIDIA Tegra30 Memory Controller
dt-bindings: memory: tegra30: Convert to Tegra124 YAML
dt-bindings: regulator: Document regulators coupling of NVIDIA Tegra20/30 SoCs
dt-bindings: clock: tegra: Rename SOR0_LVDS to SOR0_OUT
Link: https://lore.kernel.org/r/20191102144521.3863321-1-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Add device-tree binding for NVIDIA Tegra30 External Memory Controller.
The binding is based on the Tegra124 EMC binding since hardware is
similar, although there are couple significant differences.
Note that the memory timing description is given in a platform-specific
form because there is no detailed information on how to convert a
typical-common DDR timing into the register values. The timing format is
borrowed from downstream kernel, hence there is no hurdle in regards to
upstreaming of memory timings for the boards.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra30 binding will actually differ from the Tegra124 a tad, in
particular the EMEM configuration description. Hence rename the binding
to Tegra124 during of the conversion to YAML.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Convert Samsung Exynos SROM controller bindings to DT schema format
using json-schema.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
After adding the interrupt properties to Exynos5422 DMC bindings
example, the mapped memory region must be big enough to access
performance counters registers.
Fix also syntax errors (semicolons) and adjust indentation.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukasz Luba <l.luba@partner.samsung.com>
