Each data lane on a CSI-2 C-PHY bus uses three phase encoding and is
constructed from three physical wires. The wires are referred to as A, B
and C and their default order is ABC. However to ease hardware design
the specification allows for the wires to be switched in any order.
Add a vendor neutral property to describe the line order used. The
property name 'line-orders', the possible values it can be assigned and
there names are taken from the MIPI Discovery and Configuration (DisCo)
Specification for Imaging.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The data-lanes property maps the logical lane numbers to the physical
lane numbers. The position of an entry is the logical lane number and
its value is the physical lane number. Since one physical lane can only
map to one logical lane, no number in the list should repeat. Add the
uniqueItems constraint on the property to enforce this.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Tested-by: Julien Massot <julien.massot@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The Devicetree bindings document does not have to say in the title that
it is a "binding", but instead just describe the hardware. For shared
(re-usable) schemas, name them all as "common properties".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net> # watchdog
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # IIO
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # MMC
Acked-by: Stephen Boyd <sboyd@kernel.org> # clk
Acked-by: Vinod Koul <vkoul@kernel.org> # dma
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # media
Acked-by: Sebastian Reichel <sre@kernel.org> # power
Acked-by: Viresh Kumar <viresh.kumar@linaro.org> # opp
Link: https://lore.kernel.org/r/20221216163815.522628-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Some devices support sampling of the parallel data at both edges of the
interface pixel clock in order to reduce the pixel clock by two.
Use the pclk-sample property to reflect this feature in the device tree.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
No properly bus-type for DPI video bus, add bus-type 7 for it.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The example in video-interfaces.yaml uses a bunch of undocumented
bindings which will cause warnings when undocumented compatible checks
are enabled. The example could be fixed to use documented bindings, but
doing so would just duplicate other examples. So let's just remove the
example.
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20210324202253.3576798-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Convert video-interfaces.txt to DT schema. As it contains a mixture of
device level and endpoint properties, split it up into 2 schemas.
Binding schemas will need to reference both the graph.yaml and
video-interfaces.yaml schemas. The exact schema depends on how many
ports and endpoints for the binding. A single port with a single
endpoint looks similar to this:
port:
$ref: /schemas/graph.yaml#/$defs/port-base
properties:
endpoint:
$ref: video-interfaces.yaml#
unevaluatedProperties: false
properties:
bus-width:
enum: [ 8, 10, 12, 16 ]
pclk-sample: true
hsync-active: true
vsync-active: true
required:
- bus-width
additionalProperties: false
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
