Since the interrupt and I2C lines of AW2013 operate in open drain low
active mode a pull-up supply is needed for correct operation.
Unfortunately there is no ideal place to describe it in the DT: The
pull-up needed for the I2C lines could be described on the I2C bus.
However, the pull-up needed for the interrupt line belongs neither
directly to the interrupt controller nor to AW2013. Since the AW2013
driver will be typically in control of the power management and
interrupt masking it makes more sense to describe it inside the AW2013
device tree node.
Add it to the AW2013 DT schema together with a comment that makes it
clear what exactly it represents.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20230815-aw2013-vio-v3-2-2505296b0856@gerhold.net
Signed-off-by: Lee Jones <lee@kernel.org>
AW2013 has an optional interrupt pin "INTN" which is used to report
completion of started operations (e.g. power up or LED breath effects).
The driver does not use it (yet) but it should be described for
completeness inside the DT schema.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20230815-aw2013-vio-v3-1-2505296b0856@gerhold.net
Signed-off-by: Lee Jones <lee@kernel.org>
SPI and I2C bus node names are expected to be "spi" or "i2c",
respectively, with nothing else, a unit-address, or a '-N' index. A
pattern of 'spi0' or 'i2c0' or similar has crept in. Fix all these
cases. Mostly scripted with the following commands:
git grep -l '\si2c[0-9] {' Documentation/devicetree/ | xargs sed -i -e 's/i2c[0-9] {/i2c {/'
git grep -l '\sspi[0-9] {' Documentation/devicetree/ | xargs sed -i -e 's/spi[0-9] {/spi {/'
With this, a few errors in examples were exposed and fixed.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for the microchip,mcp251xfd.yaml
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for power-supply
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230228215433.3944508-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
The common.yaml schema allows further properties, so the bindings using
it should restrict it with unevaluatedProperties:false.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221127204058.57111-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Another round of 'allOf' removals that came in this cycle.
json-schema versions draft7 and earlier have a weird behavior in that
any keywords combined with a '$ref' are ignored (silently). The correct
form was to put a '$ref' under an 'allOf'. This behavior is now changed
in the 2019-09 json-schema spec and '$ref' can be mixed with other
keywords. The json-schema library doesn't yet support this, but the
tooling now does a fixup for this and either way works.
This has been a constant source of review comments, so let's change this
treewide so everyone copies the simpler syntax.
Signed-off-by: Rob Herring <robh@kernel.org>
