Document DU found in RZ/V2L SoC. The DU block is identical to RZ/G2L
SoC and therefore use RZ/G2L fallback to avoid any driver changes.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240218164840.57662-3-biju.das.jz@bp.renesas.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
The RZ/G2L LCD controller is composed of Frame Compression Processor
(FCPVD), Video Signal Processor (VSPD), and Display Unit (DU).
The DU module supports the following hardware features
− Display Parallel Interface (DPI) and MIPI LINK Video Interface
− Display timing master
− Generates video timings
− Selecting the polarity of output DCLK, HSYNC, VSYNC, and DE
− Supports Progressive
− Input data format (from VSPD): RGB888, RGB666
− Output data format: same as Input data format
− Supporting Full HD (1920 pixels x 1080 lines) for MIPI-DSI Output
− Supporting WXGA (1280 pixels x 800 lines) for Parallel Output
This patch documents the DU module found on RZ/G2L LCDC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20240218164840.57662-2-biju.das.jz@bp.renesas.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
TI keystone display subsystem present in AM65, AM62 and AM62A SoC support
two separate register spaces namely "common" and "common1" which can be
used by two separate hosts to program the display controller as described
in respective Technical Reference Manuals [1].
The common1 register space has similar set of configuration registers as
supported in common register space except the global configuration
registers which are exclusive to common region.
This adds binding for "common1" register region too as supported by the
hardware.
[1]:
AM62x TRM:
https://www.ti.com/lit/pdf/spruiv7 (Section 14.8.9.1 DSS Registers)
AM65x TRM:
https://www.ti.com/lit/pdf/spruid7 (Section 12.6.5 DSS Registers)
AM62A TRM:
https://www.ti.com/lit/pdf/spruj16 (Section 14.9.9 Display Subsystem Registers)
Fixes: 2d8730f102 ("dt-bindings: display: ti,am65x-dss: Add dt-schema yaml binding")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240216062426.4170528-2-devarsht@ti.com
Add the compatible for the ltk101b4029w panel, that has the same
manufacturer, general bringup and supplies but a different dsi-init-
sequence compared to the ltk500hd1829 .
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240215090515.3513817-3-heiko@sntech.de
- Improve devlink dependency parsing for DT graphs
- Fix devlink handling of io-channels dependencies
- Fix PCI addressing in marvell,prestera example
- A few schema fixes for property constraints
- Improve performance of DT unprobed devices kselftest
- Fix regression in DT_SCHEMA_FILES handling
- Fix compile error in unittest for !OF_DYNAMIC
-----BEGIN PGP SIGNATURE-----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=NqMr
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-6.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Improve devlink dependency parsing for DT graphs
- Fix devlink handling of io-channels dependencies
- Fix PCI addressing in marvell,prestera example
- A few schema fixes for property constraints
- Improve performance of DT unprobed devices kselftest
- Fix regression in DT_SCHEMA_FILES handling
- Fix compile error in unittest for !OF_DYNAMIC
* tag 'devicetree-fixes-for-6.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: ufs: samsung,exynos-ufs: Add size constraints on "samsung,sysreg"
of: property: Add in-ports/out-ports support to of_graph_get_port_parent()
of: property: Improve finding the supplier of a remote-endpoint property
of: property: Improve finding the consumer of a remote-endpoint property
net: marvell,prestera: Fix example PCI bus addressing
of: unittest: Fix compile in the non-dynamic case
of: property: fix typo in io-channels
dt-bindings: tpm: Drop type from "resets"
dt-bindings: display: nxp,tda998x: Fix 'audio-ports' constraints
dt-bindings: xilinx: replace Piyush Mehta maintainership
kselftest: dt: Stop relying on dirname to improve performance
dt-bindings: don't anchor DT_SCHEMA_FILES to bindings directory
Most Rockchip hdmi nodes are part of a power domain.
Add a power-domains property and include it to the example
with some reordering to align with the (new) documentation
about property ordering.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/5c45527a-e218-40a3-8e71-a5815417e5f7@gmail.com
The hdmi-connector nodes are now functional and the new way to model
hdmi ports nodes with both in and output port subnodes. Unfortunately
with the conversion to YAML the old method with only an input port node
was used. Later the new method was also added to the binding.
A binding must be unambiguously, so remove the old port property
entirely and make port@0 and port@1 a requirement as all
upstream dts files are updated as well and because checking
deprecated stuff is a bit pointless.
Update the example to avoid use of the removed property.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/a493c65e-7cf9-455f-95d5-8c98cad35710@gmail.com
Document the rotation property for rocktech,jh057n00900 panels.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240212184950.52210-4-macroalpha82@gmail.com
The RGB10MAX3 panel is a panel specific to the Powkiddy RGB10MAX3
handheld device that measures 5 inches diagonally with a resolution
of 720x1280.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240212184950.52210-2-macroalpha82@gmail.com
Documentation/process/license-rules.rst and checkpatch expect the SPDX
identifier syntax for multiple licenses to use capital "OR". Correct it
to keep consistent format and avoid copy-paste issues.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240208105327.129159-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
In order to check schemas for missing additionalProperties or
unevaluatedProperties, cases allowing extra properties must be explicit.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/576954/
Link: https://lore.kernel.org/r/20240202222338.1652333-1-robh@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Backmerging to update drm-misc-next to the state of v6.8-rc3. Also
fixes a build problem with xe.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
The servers for the @codeaurora domain are long retired and any messages
sent there bounce. Sandeep Panda's email address is no longer valid and
should be repleaced. However Sandeep has left the company and has not
been active sice, therefore it looks like this binding is orphaned.
Doug is listed as the reviewer for this file in MAINTAINERS and has
volunteered to be listed within the file as the binding maintainer.
Therefore replace Sandeep with Doug to make the documentation current.
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202202329.4172917-1-quic_jhugo@quicinc.com
The constraints for 'audio-ports' don't match the description. There can
be 1 or 2 DAI entries and each entry is exactly 2 values. Also, the
values' sizes are 32-bits, not 8-bits. Move the size constraints to the
outer dimension (number of DAIs) and add constraints on inner array
values.
Link: https://lore.kernel.org/r/20240122204959.1665970-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
- Minor fix in `drm/exynos: gsc: gsc_runtime_resume`
. The patch ensures `clk_disable_unprepare()` is called on the first
element of `ctx->clocks` array.
This issue was identified by the Linux Verification Center.
- Fix excessive stack usage in `fimd_win_set_pixfmt()` in `drm/exynos`
. The issue, highlighted by gcc, involved an unnecessary on-stack copy of
the large `exynos_drm_plane` structure, now replaced with a pointer.
- Fix an incorrect type issue in `exynos_drm_fimd.c` module
. Addresses an incorrect type issue in `fimd_commit()` within the
`exynos_drm_fimd.c` The problem was reported by the kernel test robot[1].
[1] https://lore.kernel.org/oe-kbuild-all/202312140930.Me9yWf8F-lkp@intel.com/
- Fix a typo in the dt-bindings for `samsung,exynos-mixer`
. Changes 'regs' to the correct property name 'reg' in the dt-bindings
documentation for `samsung,exynos-mixer`
-----BEGIN PGP SIGNATURE-----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=OkrW
-----END PGP SIGNATURE-----
Merge tag 'exynos-drm-fixes-for-v6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
Several fixups
- Minor fix in `drm/exynos: gsc: gsc_runtime_resume`
. The patch ensures `clk_disable_unprepare()` is called on the first
element of `ctx->clocks` array.
This issue was identified by the Linux Verification Center.
- Fix excessive stack usage in `fimd_win_set_pixfmt()` in `drm/exynos`
. The issue, highlighted by gcc, involved an unnecessary on-stack copy of
the large `exynos_drm_plane` structure, now replaced with a pointer.
- Fix an incorrect type issue in `exynos_drm_fimd.c` module
. Addresses an incorrect type issue in `fimd_commit()` within the
`exynos_drm_fimd.c` The problem was reported by the kernel test robot[1].
[1] https://lore.kernel.org/oe-kbuild-all/202312140930.Me9yWf8F-lkp@intel.com/
- Fix a typo in the dt-bindings for `samsung,exynos-mixer`
. Changes 'regs' to the correct property name 'reg' in the dt-bindings
documentation for `samsung,exynos-mixer`
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240122072407.39546-1-inki.dae@samsung.com
new drivers:
- imagination - new driver for Imagination Technologies GPU
- xe - new driver for Intel GPUs using core drm concepts
core:
- add CLOSE_FB ioctl
- remove old UMS ioctls
- increase max objects to accomodate AMD color mgmt
encoder:
- create per-encoder debugfs directory
edid:
- split out drm_eld
- SAD helpers
- drop edid_firmware module parameter
format-helper:
- cache format conversion buffers
sched:
- move from kthread to workqueue
- rename some internals
- implement dynamic job-flow control
gpuvm:
- provide more features to handle GEM objects
client:
- don't acquire module reference
displayport:
- add mst path property documentation
fdinfo:
- alignment fix
dma-buf:
- add fence timestamp helper
- add fence deadline support
bridge:
- transparent aux-bridge for DP/USB-C
- lt8912b: add suspend/resume support and power regulator support
panel:
- edp: AUO B116XTN02, BOE NT116WHM-N21,836X2, NV116WHM-N49
- chromebook panel support
- elida-kd35t133: rework pm
- powkiddy RK2023 panel
- himax-hx8394: drop prepare/unprepare and shutdown logic
- BOE BP101WX1-100, Powkiddy X55, Ampire AM8001280G
- Evervision VGG644804, SDC ATNA45AF01
- nv3052c: register docs, init sequence fixes, fascontek FS035VG158
- st7701: Anbernic RG-ARC support
- r63353 panel controller
- Ilitek ILI9805 panel controller
- AUO G156HAN04.0
simplefb:
- support memory regions
- support power domains
amdgpu:
- add new 64-bit sequence number infrastructure
- add AMD specific color management
- ACPI WBRF support for RF interference handling
- GPUVM updates
- RAS updates
- DCN 3.5 updates
- Rework PCIe link speed handling
- Document GPU reset types
- DMUB fixes
- eDP fixes
- NBIO 7.9/7.11 updates
- SubVP updates
- XGMI PCIe state dumping for aqua vanjaram
- GFX11 golden register updates
- enable tunnelling on high pri compute
amdkfd:
- Migrate TLB flushing logic to amdgpu
- Trap handler fixes
- Fix restore workers handling on suspend/resume
- Fix possible memory leak in pqm_uninit()
- support import/export of dma-bufs using GEM handles
radeon:
- fix possible overflows in command buffer checking
- check for errors in ring_lock
i915:
- reorg display code for reuse in xe driver
- fdinfo memory stats printing
- DP MST bandwidth mgmt improvements
- DP panel replay enabling
- MTL C20 phy state verification
- MTL DP DSC fractional bpp support
- Audio fastset support
- use dma_fence interfaces instead of i915_sw_fence
- Separate gem and display code
- AUX register macro refactoring
- Separate display module/device parameters
- Move display capabilities debugfs under display
- Makefile cleanups
- Register cleanups
- Move display lock inits under display/
- VLV/CHV DPIO PHY register and interface refactoring
- DSI VBT sequence refactoring
- C10/C20 PHY PLL hardware readout
- DPLL code cleanups
- Cleanup PXP plane protection checks
- Improve display debug msgs
- PSR selective fetch fixes/improvements
- DP MST fixes
- Xe2LPD FBC restrictions removed
- DGFX uses direct VBT pin mapping
- more MTL WAs
- fix MTL eDP bug
- eliminate use of kmap_atomic
habanalabs:
- sysfs entry to identify a device minor id with debugfs path
- sysfs entry to expose device module id
- add signed device info retrieval through INFO ioctl
- add Gaudi2C device support
- pcie reset prepare/done hooks
msm:
- Add support for SDM670, SM8650
- Handle the CFG interconnect to fix the obscure hangs / timeouts
- Kconfig fix for QMP dependency
- use managed allocators
- DPU: SDM670, SM8650 support
- DPU: Enable SmartDMA on SM8350 and SM8450
- DP: enable runtime PM support
- GPU: add metadata UAPI
- GPU: move devcoredumps to GPU device
- GPU: convert to drm_exec
ivpu:
- update FW API
- new debugfs file
- a new NOP job submission test mode
- improve suspend/resume
- PM improvements
- MMU PT optimizations
- firmware profile frequency support
- support for uncached buffers
- switch to gem shmem helpers
- replace kthread with threaded irqs
rockchip:
- rk3066_hdmi: convert to atomic
- vop2: support nv20 and nv30
- rk3588 support
mediatek:
- use devm_platform_ioremap_resource
- stop using iommu_present
- MT8188 VDOSYS1 display support
panfrost:
- PM improvements
- improve interrupt handling as poweroff
qaic:
- allow to run with single MSI
- support host/device time sync
- switch to persistent DRM devices
exynos:
- fix potential error pointer dereference
- fix wrong error checking
- add missing call to drm_atomic_helper_shutdown
omapdrm:
- dma-fence lockdep annotation fix
tidss:
- dma-fence lockdep annotation fix
- support for AM62A7
v3d:
- BCM2712 - rpi5 support
- fdinfo + gputop support
- uapi for CPU job handling
virtio-gpu:
- add context debug name
-----BEGIN PGP SIGNATURE-----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=nuw0
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2024-01-10' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This contains two major new drivers:
- imagination is a first driver for Imagination Technologies devices,
it only covers very specific devices, but there is hope to grow it
- xe is a reboot of the i915 GPU (shares display) side using a more
upstream focused development model, and trying to maximise code
sharing. It's not enabled for any hw by default, and will hopefully
get switched on for Intel's Lunarlake.
This also drops a bunch of the old UMS ioctls. It's been dead long
enough.
amdgpu has a bunch of new color management code that is being used in
the Steam Deck.
amdgpu also has a new ACPI WBRF interaction to help avoid radio
interference.
Otherwise it's the usual lots of changes in lots of places.
Detailed summary:
new drivers:
- imagination - new driver for Imagination Technologies GPU
- xe - new driver for Intel GPUs using core drm concepts
core:
- add CLOSE_FB ioctl
- remove old UMS ioctls
- increase max objects to accomodate AMD color mgmt
encoder:
- create per-encoder debugfs directory
edid:
- split out drm_eld
- SAD helpers
- drop edid_firmware module parameter
format-helper:
- cache format conversion buffers
sched:
- move from kthread to workqueue
- rename some internals
- implement dynamic job-flow control
gpuvm:
- provide more features to handle GEM objects
client:
- don't acquire module reference
displayport:
- add mst path property documentation
fdinfo:
- alignment fix
dma-buf:
- add fence timestamp helper
- add fence deadline support
bridge:
- transparent aux-bridge for DP/USB-C
- lt8912b: add suspend/resume support and power regulator support
panel:
- edp: AUO B116XTN02, BOE NT116WHM-N21,836X2, NV116WHM-N49
- chromebook panel support
- elida-kd35t133: rework pm
- powkiddy RK2023 panel
- himax-hx8394: drop prepare/unprepare and shutdown logic
- BOE BP101WX1-100, Powkiddy X55, Ampire AM8001280G
- Evervision VGG644804, SDC ATNA45AF01
- nv3052c: register docs, init sequence fixes, fascontek FS035VG158
- st7701: Anbernic RG-ARC support
- r63353 panel controller
- Ilitek ILI9805 panel controller
- AUO G156HAN04.0
simplefb:
- support memory regions
- support power domains
amdgpu:
- add new 64-bit sequence number infrastructure
- add AMD specific color management
- ACPI WBRF support for RF interference handling
- GPUVM updates
- RAS updates
- DCN 3.5 updates
- Rework PCIe link speed handling
- Document GPU reset types
- DMUB fixes
- eDP fixes
- NBIO 7.9/7.11 updates
- SubVP updates
- XGMI PCIe state dumping for aqua vanjaram
- GFX11 golden register updates
- enable tunnelling on high pri compute
amdkfd:
- Migrate TLB flushing logic to amdgpu
- Trap handler fixes
- Fix restore workers handling on suspend/resume
- Fix possible memory leak in pqm_uninit()
- support import/export of dma-bufs using GEM handles
radeon:
- fix possible overflows in command buffer checking
- check for errors in ring_lock
i915:
- reorg display code for reuse in xe driver
- fdinfo memory stats printing
- DP MST bandwidth mgmt improvements
- DP panel replay enabling
- MTL C20 phy state verification
- MTL DP DSC fractional bpp support
- Audio fastset support
- use dma_fence interfaces instead of i915_sw_fence
- Separate gem and display code
- AUX register macro refactoring
- Separate display module/device parameters
- Move display capabilities debugfs under display
- Makefile cleanups
- Register cleanups
- Move display lock inits under display/
- VLV/CHV DPIO PHY register and interface refactoring
- DSI VBT sequence refactoring
- C10/C20 PHY PLL hardware readout
- DPLL code cleanups
- Cleanup PXP plane protection checks
- Improve display debug msgs
- PSR selective fetch fixes/improvements
- DP MST fixes
- Xe2LPD FBC restrictions removed
- DGFX uses direct VBT pin mapping
- more MTL WAs
- fix MTL eDP bug
- eliminate use of kmap_atomic
habanalabs:
- sysfs entry to identify a device minor id with debugfs path
- sysfs entry to expose device module id
- add signed device info retrieval through INFO ioctl
- add Gaudi2C device support
- pcie reset prepare/done hooks
msm:
- Add support for SDM670, SM8650
- Handle the CFG interconnect to fix the obscure hangs / timeouts
- Kconfig fix for QMP dependency
- use managed allocators
- DPU: SDM670, SM8650 support
- DPU: Enable SmartDMA on SM8350 and SM8450
- DP: enable runtime PM support
- GPU: add metadata UAPI
- GPU: move devcoredumps to GPU device
- GPU: convert to drm_exec
ivpu:
- update FW API
- new debugfs file
- a new NOP job submission test mode
- improve suspend/resume
- PM improvements
- MMU PT optimizations
- firmware profile frequency support
- support for uncached buffers
- switch to gem shmem helpers
- replace kthread with threaded irqs
rockchip:
- rk3066_hdmi: convert to atomic
- vop2: support nv20 and nv30
- rk3588 support
mediatek:
- use devm_platform_ioremap_resource
- stop using iommu_present
- MT8188 VDOSYS1 display support
panfrost:
- PM improvements
- improve interrupt handling as poweroff
qaic:
- allow to run with single MSI
- support host/device time sync
- switch to persistent DRM devices
exynos:
- fix potential error pointer dereference
- fix wrong error checking
- add missing call to drm_atomic_helper_shutdown
omapdrm:
- dma-fence lockdep annotation fix
tidss:
- dma-fence lockdep annotation fix
- support for AM62A7
v3d:
- BCM2712 - rpi5 support
- fdinfo + gputop support
- uapi for CPU job handling
virtio-gpu:
- add context debug name"
* tag 'drm-next-2024-01-10' of git://anongit.freedesktop.org/drm/drm: (2340 commits)
drm/amd/display: Allow z8/z10 from driver
drm/amd/display: fix bandwidth validation failure on DCN 2.1
drm/amdgpu: apply the RV2 system aperture fix to RN/CZN as well
drm/amd/display: Move fixpt_from_s3132 to amdgpu_dm
drm/amd/display: Fix recent checkpatch errors in amdgpu_dm
Revert "drm/amdkfd: Relocate TBA/TMA to opposite side of VM hole"
drm/amd/display: avoid stringop-overflow warnings for dp_decide_lane_settings()
drm/amd/display: Fix power_helpers.c codestyle
drm/amd/display: Fix hdcp_log.h codestyle
drm/amd/display: Fix hdcp2_execution.c codestyle
drm/amd/display: Fix hdcp_psp.h codestyle
drm/amd/display: Fix freesync.c codestyle
drm/amd/display: Fix hdcp_psp.c codestyle
drm/amd/display: Fix hdcp1_execution.c codestyle
drm/amd/pm/smu7: fix a memleak in smu7_hwmgr_backend_init
drm/amdkfd: Fix iterator used outside loop in 'kfd_add_peer_prop()'
drm/amdgpu: Drop 'fence' check in 'to_amdgpu_amdkfd_fence()'
drm/amdkfd: Confirm list is non-empty before utilizing list_first_entry in kfd_topology.c
drm/amdgpu: Fix '*fw' from request_firmware() not released in 'amdgpu_ucode_request()'
drm/amdgpu: Fix variable 'mca_funcs' dereferenced before NULL check in 'amdgpu_mca_smu_get_mca_entry()'
...
There is one new SoC for each 32-bit Arm and 64-bit RISC-V, but both
the Rockchips rv1109 and Sopgho CV1812H are just minor variations of
already supported chips.
The other six new SoCs are all part of existing arm64 families, but
are somewhat more interesting:
- Samsung ExynosAutov920 is an automotive chip, and the first one
we support based on the Cortex-A78AE core with lockstep mode.
- Google gs101 (Tensor G1) is the chip used in a number of Pixel phones,
and is grouped with Samsung Exynos here since it is based on the same
SoC design, sharing most of its IP blocks with that series.
- MediaTek MT8188 is a new chip used for mid-range tablets and Chromebooks,
using two Cortex-A78 cores where the older MT8195 had four of them.
- Qualcomm SM8650 (Snapdragon 8 Gen 3) is their current top range
phone SoC and the first supported chip based on Cortex-X4, Cortex-A720
and Cortex-A520.
- Qualcomm X1E80100 (Snapdragon X Elite) in turn is the latest
Laptop chip using the custom Oryon cores.
- Unisoc UMS9620 (Tanggula 7 series) is a 5G phone SoC based on
Cortex-A76 and Cortex-A55
In terms of boards, we have
- Five old Microsoft Lumia phones, the HTC One Mini 2, Motorola Moto
G 4G, and Huawei Honor 5X/GR5, all based on Snapdragon SoCs.
- Multiple Rockchips mobile gaming systems (Anbernic RG351V,
Powkiddy RK2023, Powkiddy X55) along with the Sonoff iHost Smart
Home Hub and a few Rockchips SBCs
- Some ComXpress boards based on Marvell CN913x, which is the
follow-up to Armada 7xxx/8xxx.
- Six new industrial/embedded boards based on NXP i.MX8 and i.MX9
- Mediatek MT8183 based Chromebooks from Lenovo, Asus and Acer.
- Toradex Verdin AM62 Mallow carrier for TI AM62
- Huashan Pi board based on the SophGo CV1812H RISC-V chip
- Two boards based on Allwinner H616/H618
- A number of reference boards for various added SoCs from Qualcomm,
Mediatek, Google, Samsung, NXP and Spreadtrum
As usual, there are cleanups and warning fixes across all platforms as
well as added features for several of them.
-----BEGIN PGP SIGNATURE-----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=zR3G
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC DT updates from Arnd Bergmann:
"There is one new SoC for each 32-bit Arm and 64-bit RISC-V, but both
the Rockchips rv1109 and Sopgho CV1812H are just minor variations of
already supported chips.
The other six new SoCs are all part of existing arm64 families, but
are somewhat more interesting:
- Samsung ExynosAutov920 is an automotive chip, and the first one we
support based on the Cortex-A78AE core with lockstep mode.
- Google gs101 (Tensor G1) is the chip used in a number of Pixel
phones, and is grouped with Samsung Exynos here since it is based
on the same SoC design, sharing most of its IP blocks with that
series.
- MediaTek MT8188 is a new chip used for mid-range tablets and
Chromebooks, using two Cortex-A78 cores where the older MT8195 had
four of them.
- Qualcomm SM8650 (Snapdragon 8 Gen 3) is their current top range
phone SoC and the first supported chip based on Cortex-X4,
Cortex-A720 and Cortex-A520.
- Qualcomm X1E80100 (Snapdragon X Elite) in turn is the latest Laptop
chip using the custom Oryon cores.
- Unisoc UMS9620 (Tanggula 7 series) is a 5G phone SoC based on
Cortex-A76 and Cortex-A55
In terms of boards, we have
- Five old Microsoft Lumia phones, the HTC One Mini 2, Motorola Moto
G 4G, and Huawei Honor 5X/GR5, all based on Snapdragon SoCs.
- Multiple Rockchips mobile gaming systems (Anbernic RG351V, Powkiddy
RK2023, Powkiddy X55) along with the Sonoff iHost Smart Home Hub
and a few Rockchips SBCs
- Some ComXpress boards based on Marvell CN913x, which is the
follow-up to Armada 7xxx/8xxx.
- Six new industrial/embedded boards based on NXP i.MX8 and i.MX9
- Mediatek MT8183 based Chromebooks from Lenovo, Asus and Acer.
- Toradex Verdin AM62 Mallow carrier for TI AM62
- Huashan Pi board based on the SophGo CV1812H RISC-V chip
- Two boards based on Allwinner H616/H618
- A number of reference boards for various added SoCs from Qualcomm,
Mediatek, Google, Samsung, NXP and Spreadtrum
As usual, there are cleanups and warning fixes across all platforms as
well as added features for several of them"
* tag 'soc-dt-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (857 commits)
ARM: dts: usr8200: Fix phy registers
arm64: dts: intel: minor whitespace cleanup around '='
arm64: dts: socfpga: agilex: drop redundant status
arm64: dts: socfpga: agilex: add unit address to soc node
arm64: dts: socfpga: agilex: move firmware out of soc node
arm64: dts: socfpga: agilex: move FPGA region out of soc node
arm64: dts: socfpga: agilex: align pin-controller name with bindings
arm64: dts: socfpga: stratix10_swvp: drop unsupported DW MSHC properties
arm64: dts: socfpga: stratix10_socdk: align NAND chip name with bindings
arm64: dts: socfpga: stratix10: add unit address to soc node
arm64: dts: socfpga: stratix10: move firmware out of soc node
arm64: dts: socfpga: stratix10: move FPGA region out of soc node
arm64: dts: socfpga: stratix10: align pincfg nodes with bindings
arm64: dts: socfpga: stratix10: add clock-names to DWC2 USB
arm64: dts: socfpga: drop unsupported cdns,page-size and cdns,block-size
ARM: dts: socfpga: align NAND controller name with bindings
ARM: dts: socfpga: drop unsupported cdns,page-size and cdns,block-size
arm64: dts: rockchip: Fix led pinctrl of lubancat 1
arm64: dts: rockchip: correct gpio_pwrctrl1 typo on nanopc-t6
arm64: dts: rockchip: correct gpio_pwrctrl1 typo on rock-5b
...
The integration for this SoC is different from the currently existing: It
needs it's PHY's reference clock rate to calculate the DDC bus frequency
correctly. The controller is also part of a powerdomain, so this gets added
as an mandatory property for this variant.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231222174220.55249-2-knaerzche@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
The correct property name is 'reg' not 'regs'.
Fixes: 68e89bb36d ("dt-bindings: display: samsung,exynos-mixer: convert to dtschema")
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Updates for v6.8:
Core:
- Add support for SDM670, SM8650
- Handle the CFG interconnect to fix the obscure hangs / timeouts
on register write
- Kconfig fix for QMP dependency
- DT schema fixes
DPU:
- Add support for SDM670, SM8650
- Enable SmartDMA on SM8350 and SM8450
- Correct UBWC settings for SC8280XP
- Fix catalog settings for SC8180X
- Actually make use of the version to switch between QSEED3/3LITE/4
scalers
- Use devres-managed and drm-managed allocations where appropriate
- misc other fixes
- Enabled YUV writeback on SC7280, SM8250
- Enabled writeback on SM8350, SM8450
- CRC fix when encoder is selected as the input source
- other misc fixes
MDP4:
- Use devres-managed and drm-managed allocations where appropriate
- flush vblank event on CRTC disable
MDP5:
- Use devres-managed and drm-managed allocations where appropriate
DP:
- Add support for SM8650
- Enable PM runtime support
- Merge msm-specific debugfs dir with the generic one
- Described DisplayPort on SM8150 in DeviceTree bindings
- Moved dp_display_get_next_bridge() to probe()
DSI:
- Add support for SM8650
- Enable PM runtime support
GPU/GEM:
- demote userspace triggerable warnings to debug
- add GEM object metadata UAPI
- move GPU devcoredumps to GPU device
- fix hangcheck to skip retired submits
- expose UBWC config to userspace
- fix a680 chip-id
- drm_exec conversion
- drm/ci: remove rebase-merge directory (to unblock CI)
[airlied: fix drm_exec/amd interaction]
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGs9auYqmo-7NSd9FsbNBCDf7aBevd=4xkcF3A5G_OGvMQ@mail.gmail.com
UAPI Changes:
Cross-subsystem Changes:
- A few fixes for usb/typec
Core Changes:
- ci: Updates to the defconfig, igt version, etc.
- writeback: Move the atomic_check helper from the encoder to connector
Driver Changes:
- rockchip: Add support for rk3588
- xe: Update the TODO list
- panel:
- nv3052c: Register documentation, init sequence improvements and
support for the Fascontek FS035VG158
- st7701: Add support for the Anbernic RG-ARC
- new driver: Synaptics R63353 panel controller, Ilitek ILI9805 panel
controller
- new panel: AUO G156HAN04.0
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCZXrMAwAKCRDj7w1vZxhR
xa+2AP9ZyK/PP5/a1y1PKUQ9IYPjRW0QEda2I7w1XK6hglSWDgD9Hu9Q8YPUtlTT
PT0qZ++tdxnCiGgj+yK3Yc1qPcb6+Qw=
=o4Gu
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2023-12-14' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for $kernel-version:
UAPI Changes:
Cross-subsystem Changes:
- A few fixes for usb/typec
Core Changes:
- ci: Updates to the defconfig, igt version, etc.
- writeback: Move the atomic_check helper from the encoder to connector
Driver Changes:
- rockchip: Add support for rk3588
- xe: Update the TODO list
- panel:
- nv3052c: Register documentation, init sequence improvements and
support for the Fascontek FS035VG158
- st7701: Add support for the Anbernic RG-ARC
- new driver: Synaptics R63353 panel controller, Ilitek ILI9805 panel
controller
- new panel: AUO G156HAN04.0
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/aqpn5miejmkks7pbcfex7b6u63uwsruywxsnr3x5ljs45qatin@nbkkej2elk46
The vop2 on rk3588 is similar to which on rk356x
but with 4 video ports and need to reference
more grf modules.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231211115850.1785311-1-andyshrk@163.com
Originally was in the panel-simple, but belongs to panel-simple-dsi.
See arch/arm/boot/dts/nvidia/tegra114-roth.dts for more details.
Resolves the following warning:
```
arch/arm/boot/dts/tegra114-roth.dt.yaml: panel@0: 'reg' does not match any of the regexes: 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/display/panel/panel-simple.yaml
```
Fixes: 310abcea76 ("dt-bindings: display: convert simple lg panels to DT Schema")
Signed-off-by: David Heidelberg <david@ixit.cz>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Link: https://lore.kernel.org/r/20231212200934.99262-1-david@ixit.cz
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231212200934.99262-1-david@ixit.cz
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmV2PMQeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGhgQIAKSdjtpkv+IeDwph
umLHxDlCTT8nl+TAhEYuxSdMiHt1i7+zyF0snnHhGthBRnBZBf+PDdkQOmqtjLZj
e591VGY7tdNCAVUwmRRaI82JFz9Pl1k8DXL3f+CE1+MfbpsirAecoIAL0rsvg+4f
ICKSAOBZonL7GT7IGrsbxgqGKCLC+2PcgNT4pADBdjtbC1nmVSLK21dtWr6i4xsn
CT9MxAnej1+EOpreyHhNZUVqfQy0/04x4OY0u/EOXU3PgpfGTrAzkyfwzcd/eit0
x59TZ0owDVXfvvdXUUAC0zG1th2ek5LKNtL+C4rKOoAbq7GZoQfjN5M/Ug+yykwE
aqm6CJ8=
=tZ+R
-----END PGP SIGNATURE-----
Backmerge tag 'v6.7-rc5' into drm-next
Linux 6.7-rc5
Alex requested this for some amdkfd work relying on the symbols exports.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add the compatible string for MediaTek MT8195 SoC, using the same DSI
block as the MT8183.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add a compatible string for the PADDING block in MediaTek MT8195 that
is controlled by MDP3.
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add compatible string and GCE property for MT8195 SPLIT, of
which is operated by MDP3.
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add a compatible string for the OVL block in MediaTek MT8195 that
is controlled by MDP3.
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add a compatible string for the MERGE block in MediaTek MT8195 that
is controlled by MDP3.
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add a compatible string for the COLOR block in MediaTek MT8195 that
is controlled by MDP3.
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add a compatible string for the AAL block in MediaTek MT8195 that
is controlled by MDP3.
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
To simplify maintenance and avoid branches, the identical component
should be merged and placed in the path belonging to the MDP
(from display/* to media/*).
In addition, currently only MDP utilizes RDMA through CMDQ, and the
necessary properties for "mediatek,gce-events", and "mboxes" have been
set up for this purpose.
Within DISP, it directly receives component interrupt signals.
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Padding is a new hardware module on MediaTek MT8188,
add dt-bindings for it.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add compatible name for MediaTek MT8188 MERGE.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add compatible name for MediaTek MT8188 MDP-RDMA.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Add compatible name for MediaTek MT8188 ETHDR.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Document support for the AUO G156HAN04.0 LVDS display.
G156HAN04.0 is a Color Active Matrix Liquid Crystal Display composed of
a TFT LCD panel, a driver circuit, and LED backlight system. The screen
format is intended to support the 16:9 FHD, 1920(H) x 1080(V) screen
and 16.7M colors (RGB 8-bits) with LED backlight driving circuit.
All input signals are LVDS interface compatible.
G156HAN04.0 is designed for a display unit of notebook style
personal computer and industrial machine.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Elmar Albert <ealbert@data-modul.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20231209063714.1381913-1-marex@denx.de
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231209063714.1381913-1-marex@denx.de
Padding is a new hardware module on MediaTek MT8188,
add dt-bindings for it.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20231024130048.14749-5-shawn.sung@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add compatible name for MediaTek MT8188 MERGE.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20231024130048.14749-4-shawn.sung@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add compatible name for MediaTek MT8188 MDP-RDMA.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20231024130048.14749-3-shawn.sung@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add compatible name for MediaTek MT8188 ETHDR.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20231024130048.14749-2-shawn.sung@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
- Fix dt-extract-compatibles for builds with in tree build directory
- Drop Xinlei Lee <xinlei.lee@mediatek.com> bouncing email
- Fix the of_reconfig_get_state_change() return value documentation
- Add missing #power-domain-cells property to QCom MPM
- Fix warnings in i.MX LCDIF and adi,adv7533
-----BEGIN PGP SIGNATURE-----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=+lyN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Fix dt-extract-compatibles for builds with in tree build directory
- Drop Xinlei Lee <xinlei.lee@mediatek.com> bouncing email
- Fix the of_reconfig_get_state_change() return value documentation
- Add missing #power-domain-cells property to QCom MPM
- Fix warnings in i.MX LCDIF and adi,adv7533
* tag 'devicetree-fixes-for-6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: display: adi,adv75xx: Document #sound-dai-cells
dt-bindings: lcdif: Properly describe the i.MX23 interrupts
dt-bindings: interrupt-controller: Allow #power-domain-cells
of: dynamic: Fix of_reconfig_get_state_change() return value documentation
dt-bindings: display: mediatek: dsi: remove Xinlei's mail
dt: dt-extract-compatibles: Don't follow symlinks when walking tree
When using audio from ADV7533 or ADV7535 and describing the audio
card via simple-audio-card, the '#sound-dai-cells' needs to be passed.
Document the '#sound-dai-cells' property to fix the following
dt-schema warning:
imx8mn-beacon-kit.dtb: hdmi@3d: '#sound-dai-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/bridge/adi,adv7533.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20231206093643.2198562-1-festevam@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
i.MX23 has two LCDIF interrupts instead of a single one like other
i.MX devices.
Take this into account for properly describing the i.MX23 LCDIF
interrupts.
This fixes the following dt-schema warning:
imx23-olinuxino.dtb: lcdif@80030000: interrupts: [[46], [45]] is too long
from schema $id: http://devicetree.org/schemas/display/fsl,lcdif.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231206112337.2234849-1-festevam@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
The SDM670 display controller has the same requirements as the SDM845
display controller, despite having distinct properties as described in
the catalog. Add the compatible for SDM670 to the SDM845 controller.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/562959/
Link: https://lore.kernel.org/r/20231017021805.1083350-11-mailingradian@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Apart from the already handled data bus (MAS_MDP_Pn<->DDR), there are
other connection paths:
- a path that connects rotator block to the DDR.
- a path that needs to be handled to ensure MDSS register access
functions properly, namely the "reg bus", a.k.a the CPU-MDSS CFG
interconnect.
Describe these paths to allow using them in device trees and in the
driver.
[Konrad: rework for one vs two MDP paths, update examples]
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/569480/
Link: https://lore.kernel.org/r/20231125-topic-rb1_feat-v3-2-4cbb567743bb@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The "qcom,dsi-ctrl-6g-qcm2290" has been deprecated in
commit 0c0f65c6dd ("dt-bindings: msm: dsi-controller-main: Add
compatible strings for every current SoC"), but the example hasn't been
updated to reflect that.
Fix that.
Fixes: 0c0f65c6dd ("dt-bindings: msm: dsi-controller-main: Add compatible strings for every current SoC")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/569478/
Link: https://lore.kernel.org/r/20231125-topic-rb1_feat-v3-1-4cbb567743bb@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Qualcomm SM8150 MDSS comes with a bit different 7nm DSI PHY with its own
compatible. DTS already use it:
sa8155p-adp.dtb: display-subsystem@ae00000: phy@ae94400:compatible:0: 'qcom,dsi-phy-7nm' was expected
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Patchwork: https://patchwork.freedesktop.org/patch/567178/
Link: https://lore.kernel.org/r/20231111142017.51922-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Document the DisplayPort controller node in MDSS binding, already used
in DTS:
sm8250-xiaomi-elish-boe.dtb: display-subsystem@ae00000: Unevaluated properties are not allowed ('displayport-controller@ae90000' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Patchwork: https://patchwork.freedesktop.org/patch/566297/
Link: https://lore.kernel.org/r/20231107103600.27424-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The DSS controller on TI's AM62A7 SoC is an update from that on TI's
AM625 SoC. Like the DSS in AM625, the DSS in this SoC has 2 video
pipelines, but unlike the former, the latter only has one output port on
VP2 to service DPI display sinks.
Add the new controller's compatible.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20231108171619.978438-2-a-bhatia1@ti.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Xinlei Lee's mail is bouncing:
<xinlei.lee@mediatek.com>: host mailgw02.mediatek.com[216.200.240.185] said:
550 Relaying mail to xinlei.lee@mediatek.com is not allowed (in reply to
RCPT TO command)
Remove it.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231123134927.2034024-1-mwalle@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Update the NewVision NV3051D compatible strings by adding a new panel,
the powkiddy,rk2023-panel, and removing another entry, the
anbernic,rg353v-panel.
The rk2023-panel is similar to the rg353p-panel but has slightly
different timings so it needs a new string.
The rg353v-panel is duplicate to the rg353p-panel, so remove it. No
current devices use it and changes to the driver mean it is no longer
valid as a compatible string.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231117202536.1387815-2-macroalpha82@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231117202536.1387815-2-macroalpha82@gmail.com
Currently, there are two drivers for the LCD controller on Renesas
SuperH-based and ARM-based SH-Mobile and R-Mobile SoCs:
1. sh_mobile_lcdcfb, using the fbdev framework,
2. shmob_drm, using the DRM framework.
However, only the former driver is used, as all platform support
integrates the former. None of these drivers support DT-based systems.
Convert the SH-Mobile DRM driver to atomic modesetting, and add DT
support, complemented by the customary set of fixes and improvements.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/cover.1694767208.git.geert+renesas@glider.be/
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCZS0HuQAKCRCKwlD9ZEnx
cI+KAP9PThUJqV7z1YxVeM/qYWYhqR4wezD18QCanCguAIvx9wD9F2ccIsFOso35
iIv23N4D6gWJllaA2WBeKye3zYEjDQI=
=RSnM
-----END PGP SIGNATURE-----
Merge tag 'shmob-drm-atomic-dt-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into drm-next
drm: renesas: shmobile: Atomic conversion + DT support
Currently, there are two drivers for the LCD controller on Renesas
SuperH-based and ARM-based SH-Mobile and R-Mobile SoCs:
1. sh_mobile_lcdcfb, using the fbdev framework,
2. shmob_drm, using the DRM framework.
However, only the former driver is used, as all platform support
integrates the former. None of these drivers support DT-based systems.
Convert the SH-Mobile DRM driver to atomic modesetting, and add DT
support, complemented by the customary set of fixes and improvements.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/cover.1694767208.git.geert+renesas@glider.be/
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://patchwork.freedesktop.org/patch/msgid/CAMuHMdUF61V5qNyKbrTGxZfEJvCVuLO7q2R5MqZYkzRC_cNr0w@mail.gmail.com
kernel:
- add initial vmemdup-user-array
core:
- fix platform remove() to return void
- drm_file owner updated to reflect owner
- move size calcs to drm buddy allocator
- let GPUVM build as a module
- allow variable number of run-queues in scheduler
edid:
- handle bad h/v sync_end in EDIDs
panfrost:
- add Boris as maintainer
fbdev:
- use fb_ops helpers more
- only allow logo use from fbcon
- rename fb_pgproto to pgprot_framebuffer
- add HPD state to drm_connector_oob_hotplug_event
- convert to fbdev i/o mem helpers
i915:
- Enable meteorlake by default
- Early Xe2 LPD/Lunarlake display enablement
- Rework subplatforms into IP version checks
- GuC based TLB invalidation for Meteorlake
- Display rework for future Xe driver integration
- LNL FBC features
- LNL display feature capability reads
- update recommended fw versions for DG2+
- drop fastboot module parameter
- added deviceid for Arrowlake-S
- drop preproduction workarounds
- don't disable preemption for resets
- cleanup inlines in headers
- PXP firmware loading fix
- Fix sg list lengths
- DSC PPS state readout/verification
- Add more RPL P/U PCI IDs
- Add new DG2-G12 stepping
- DP enhanced framing support to state checker
- Improve shared link bandwidth management
- stop using GEM macros in display code
- refactor related code into display code
- locally enable W=1 warnings
- remove PSR watchdog timers on LNL
amdgpu:
- RAS/FRU EEPROM updatse
- IP discovery updatses
- GC 11.5 support
- DCN 3.5 support
- VPE 6.1 support
- NBIO 7.11 support
- DML2 support
- lots of IP updates
- use flexible arrays for bo list handling
- W=1 fixes
- Enable seamless boot in more cases
- Enable context type property for HDMI
- Rework GPUVM TLB flushing
- VCN IB start/size alignment fixes
amdkfd:
- GC 10/11 fixes
- GC 11.5 support
- use partial migration in GPU faults
radeon:
- W=1 Fixes
- fix some possible buffer overflow/NULL derefs
nouveau:
- update uapi for NO_PREFETCH
- scheduler/fence fixes
- rework suspend/resume for GSP-RM
- rework display in preparation for GSP-RM
habanalabs:
- uapi: expose tsc clock
- uapi: block access to eventfd through control device
- uapi: force dma-buf export to PAGE_SIZE alignments
- complete move to accel subsystem
- move firmware interface include files
- perform hard reset on PCIe AXI drain event
- optimise user interrupt handling
msm:
- DP: use existing helpers for DPCD
- DPU: interrupts reworked
- gpu: a7xx (a730/a740) support
- decouple msm_drv from kms for headless devices
mediatek:
- MT8188 dsi/dp/edp support
- DDP GAMMA - 12 bit LUT support
- connector dynamic selection capability
rockchip:
- rv1126 mipi-dsi/vop support
- add planar formats
ast:
- rename constants
panels:
- Mitsubishi AA084XE01
- JDI LPM102A188A
- LTK050H3148W-CTA6
ivpu:
- power management fixes
qaic:
- add detach slice bo api
komeda:
- add NV12 writeback
tegra:
- support NVSYNC/NHSYNC
- host1x suspend fixes
ili9882t:
- separate into own driver
-----BEGIN PGP SIGNATURE-----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=l79u
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2023-10-31-1' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Highlights:
- AMD adds some more upcoming HW platforms
- Intel made Meteorlake stable and started adding Lunarlake
- nouveau has a bunch of display rework in prepartion for the NVIDIA
GSP firmware support
- msm adds a7xx support
- habanalabs has finished migration to accel subsystem
Detail summary:
kernel:
- add initial vmemdup-user-array
core:
- fix platform remove() to return void
- drm_file owner updated to reflect owner
- move size calcs to drm buddy allocator
- let GPUVM build as a module
- allow variable number of run-queues in scheduler
edid:
- handle bad h/v sync_end in EDIDs
panfrost:
- add Boris as maintainer
fbdev:
- use fb_ops helpers more
- only allow logo use from fbcon
- rename fb_pgproto to pgprot_framebuffer
- add HPD state to drm_connector_oob_hotplug_event
- convert to fbdev i/o mem helpers
i915:
- Enable meteorlake by default
- Early Xe2 LPD/Lunarlake display enablement
- Rework subplatforms into IP version checks
- GuC based TLB invalidation for Meteorlake
- Display rework for future Xe driver integration
- LNL FBC features
- LNL display feature capability reads
- update recommended fw versions for DG2+
- drop fastboot module parameter
- added deviceid for Arrowlake-S
- drop preproduction workarounds
- don't disable preemption for resets
- cleanup inlines in headers
- PXP firmware loading fix
- Fix sg list lengths
- DSC PPS state readout/verification
- Add more RPL P/U PCI IDs
- Add new DG2-G12 stepping
- DP enhanced framing support to state checker
- Improve shared link bandwidth management
- stop using GEM macros in display code
- refactor related code into display code
- locally enable W=1 warnings
- remove PSR watchdog timers on LNL
amdgpu:
- RAS/FRU EEPROM updatse
- IP discovery updatses
- GC 11.5 support
- DCN 3.5 support
- VPE 6.1 support
- NBIO 7.11 support
- DML2 support
- lots of IP updates
- use flexible arrays for bo list handling
- W=1 fixes
- Enable seamless boot in more cases
- Enable context type property for HDMI
- Rework GPUVM TLB flushing
- VCN IB start/size alignment fixes
amdkfd:
- GC 10/11 fixes
- GC 11.5 support
- use partial migration in GPU faults
radeon:
- W=1 Fixes
- fix some possible buffer overflow/NULL derefs
nouveau:
- update uapi for NO_PREFETCH
- scheduler/fence fixes
- rework suspend/resume for GSP-RM
- rework display in preparation for GSP-RM
habanalabs:
- uapi: expose tsc clock
- uapi: block access to eventfd through control device
- uapi: force dma-buf export to PAGE_SIZE alignments
- complete move to accel subsystem
- move firmware interface include files
- perform hard reset on PCIe AXI drain event
- optimise user interrupt handling
msm:
- DP: use existing helpers for DPCD
- DPU: interrupts reworked
- gpu: a7xx (a730/a740) support
- decouple msm_drv from kms for headless devices
mediatek:
- MT8188 dsi/dp/edp support
- DDP GAMMA - 12 bit LUT support
- connector dynamic selection capability
rockchip:
- rv1126 mipi-dsi/vop support
- add planar formats
ast:
- rename constants
panels:
- Mitsubishi AA084XE01
- JDI LPM102A188A
- LTK050H3148W-CTA6
ivpu:
- power management fixes
qaic:
- add detach slice bo api
komeda:
- add NV12 writeback
tegra:
- support NVSYNC/NHSYNC
- host1x suspend fixes
ili9882t:
- separate into own driver"
* tag 'drm-next-2023-10-31-1' of git://anongit.freedesktop.org/drm/drm: (1803 commits)
drm/amdgpu: Remove unused variables from amdgpu_show_fdinfo
drm/amdgpu: Remove duplicate fdinfo fields
drm/amd/amdgpu: avoid to disable gfxhub interrupt when driver is unloaded
drm/amdgpu: Add EXT_COHERENT support for APU and NUMA systems
drm/amdgpu: Retrieve CE count from ce_count_lo_chip in EccInfo table
drm/amdgpu: Identify data parity error corrected in replay mode
drm/amdgpu: Fix typo in IP discovery parsing
drm/amd/display: fix S/G display enablement
drm/amdxcp: fix amdxcp unloads incompletely
drm/amd/amdgpu: fix the GPU power print error in pm info
drm/amdgpu: Use pcie domain of xcc acpi objects
drm/amd: check num of link levels when update pcie param
drm/amdgpu: Add a read to GFX v9.4.3 ring test
drm/amd/pm: call smu_cmn_get_smc_version in is_mode1_reset_supported.
drm/amdgpu: get RAS poison status from DF v4_6_2
drm/amdgpu: Use discovery table's subrevision
drm/amd/display: 3.2.256
drm/amd/display: add interface to query SubVP status
drm/amd/display: Read before writing Backlight Mode Set Register
drm/amd/display: Disable SYMCLK32_SE RCO on DCN314
...
- Add a kselftest to check for unprobed DT devices
- Fix address translation for some 3 address cells cases
- Refactor firmware node refcounting for AMBA bus
- Add bindings for qcom,sm4450-pdc, Qualcomm Kryo 465 CPU, and Freescale
QMC HDLC
- Add Marantec vendor prefix
- Convert qcom,pm8921-keypad, cnxt,cx92755-wdt, da9062-wdt,
and atmel,at91rm9200-wdt bindings to DT schema
- Several additionalProperties/unevaluatedProperties on child node
schemas fixes
- Drop reserved-memory bindings which now live in dtschema project
- Fix a reference to rockchip,inno-usb2phy.yaml
- Remove backlight nodes from display panel examples
- Expand example for using DT_SCHEMA_FILES
- Merge simple LVDS panel bindings to one binding doc
-----BEGIN PGP SIGNATURE-----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=JCj5
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Add a kselftest to check for unprobed DT devices
- Fix address translation for some 3 address cells cases
- Refactor firmware node refcounting for AMBA bus
- Add bindings for qcom,sm4450-pdc, Qualcomm Kryo 465 CPU, and
Freescale QMC HDLC
- Add Marantec vendor prefix
- Convert qcom,pm8921-keypad, cnxt,cx92755-wdt, da9062-wdt, and
atmel,at91rm9200-wdt bindings to DT schema
- Several additionalProperties/unevaluatedProperties on child node
schemas fixes
- Drop reserved-memory bindings which now live in dtschema project
- Fix a reference to rockchip,inno-usb2phy.yaml
- Remove backlight nodes from display panel examples
- Expand example for using DT_SCHEMA_FILES
- Merge simple LVDS panel bindings to one binding doc
* tag 'devicetree-for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (34 commits)
dt-bindings: soc: fsl: cpm_qe: cpm1-scc-qmc: Add support for QMC HDLC
dt-bindings: soc: fsl: cpm_qe: cpm1-scc-qmc: Add 'additionalProperties: false' in child nodes
dt-bindings: soc: fsl: cpm_qe: cpm1-scc-qmc: Fix example property name
dt-bindings: arm,coresight-cti: Add missing additionalProperties on child nodes
dt-bindings: arm,coresight-cti: Drop type for 'cpu' property
dt-bindings: soundwire: Add reference to soundwire-controller.yaml schema
dt-bindings: input: syna,rmi4: Make "additionalProperties: true" explicit
media: dt-bindings: ti,ds90ub960: Add missing type for "i2c-alias"
dt-bindings: input: qcom,pm8921-keypad: convert to YAML format
of: overlay: unittest: overlay_bad_unresolved: Spelling s/ok/okay/
of: address: Consolidate bus .map() functions
of: address: Store number of bus flag cells rather than bool
of: unittest: Add tests for address translations
of: address: Remove duplicated functions
of: address: Fix address translation when address-size is greater than 2
dt-bindings: watchdog: cnxt,cx92755-wdt: convert txt to yaml
dt-bindings: watchdog: da9062-wdt: convert txt to yaml
dt-bindings: watchdog: fsl,scu-wdt: Document imx8dl
dt-bindings: watchdog: atmel,at91rm9200-wdt: convert txt to yaml
dt-bindings: usb: rockchip,dwc3: update inno usb2 phy binding name
...
drm-misc-next for v6.7-rc1:
drm-misc-next-2023-10-19 + following:
UAPI Changes:
Cross-subsystem Changes:
- Convert fbdev drivers to use fbdev i/o mem helpers.
Core Changes:
- Use cross-references for macros in docs.
- Make drm_client_buffer_addb use addfb2.
- Add NV20 and NV30 YUV formats.
- Documentation updates for create_dumb ioctl.
- CI fixes.
- Allow variable number of run-queues in scheduler.
Driver Changes:
- Rename drm/ast constants.
- Make ili9882t its own driver.
- Assorted fixes in ivpu, vc4, bridge/synopsis, amdgpu.
- Add planar formats to rockchip.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3d92fae8-9b1b-4165-9ca8-5fda11ee146b@linux.intel.com
Updates for v6.7
DP:
- use existing helpers for DPCD handling instead of open-coded functions
- set the subconnector type according to the plugged cable / dongle
skip validity check for DP CTS EDID checksum
DPU:
- continued migration of feature flags to use core revision checks
- reworked interrupts code to use '0' as NO_IRQ, removed raw IRQ indices
from log / trace output
gpu:
- a7xx support (a730, a740)
- fixes and additional speedbins for a635, a643
core:
- decouple msm_drv from kms to more cleanly support headless devices (like
imx5+a2xx)
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvzkBL2_OgyOeP_b6rVEjrNdfm8jcKzaB04HqHyT5jYwA@mail.gmail.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmU1ngkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGrsIH/0k/+gdBBYFFdEym
foRhKir9WV3ZX4oIozJjA1f7T+qVYclKs6kaYm3gNepRBb6AoG8pdgv4MMAqhYsf
QMe2XHi0MrO/qKBgfNfivxEa9jq+0QK5uvTbqCRqCAB8LfwVyDqapCmg3EuiZcPW
UbMITmnwLIfXgPxvp9rabmCsTqO6FLbf0GDOVIkNSAIDBXMpcO1iffjrWUbhRa7n
oIoiJmWJLcXLxPWDsRKbpJwzw2cIG08YhfQYAiQnC3YaeRm1FKLDIICRBsmfYzja
rWv9r4dn4TDfV4/AnjggQnsZvz2yPCxNaFSQIT88nIeiLvyuUTJ9j8aidsSfMZQf
xZAbzbA=
=NoQv
-----END PGP SIGNATURE-----
BackMerge tag 'v6.6-rc7' into drm-next
This is needed to add the msm pr which is based on a higher base.
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are DT properties that can be shared across different Solomon OLED
Display Controller families. Split them into a separate common schema to
avoid these properties to be duplicated in different DT bindings schemas.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231014071520.1342189-6-javierm@redhat.com
The Powkiddy RGB30 panel is a 4 inch 720x720 MIPI-DSI LCD panel. It
appears to be based on the ST7703 LCD controller (this is assumed from
the init sequence similarity between this and other displays). Powkiddy
would not share the part number or name for the display from the bill
of materials and there were no obvious external markings, so name the
panel for the device (Powkiddy RGB30).
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231013183918.225666-3-macroalpha82@gmail.com
Freescale i.MX93 SoC embeds a Synopsys Designware MIPI DSI host
controller and a Synopsys Designware MIPI DPHY. Some configurations
and extensions to them are controlled by i.MX93 media blk-ctrl.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-9-victor.liu@nxp.com
The LTK050H3148W-CTA6 is a 5.0" 720x1280 DSI display, whose driving
controller is a Himax HX8394-F, slightly different from LTK050H3146W by
its init sequence, mode details and mode flags.
Cc: Quentin Schulz <foss+kernel@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220131164723.714836-3-quentin.schulz@theobroma-systems.com
Allow A7xx SKUs, such as the A730 GPU found on SM8450 and friends.
They use GMU for all things DVFS, just like most A6xx GPUs.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # sm8450
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/559281/
Signed-off-by: Rob Clark <robdclark@chromium.org>
When booting the GMU, the QMP mailbox should be pinged about some tunables
(e.g. adaptive clock distribution state). To achieve that, a reference to
it is necessary. Allow it and require it with A730.
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # sm8450
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/559279/
Signed-off-by: Rob Clark <robdclark@chromium.org>
The GMU on the A7xx series is pretty much the same as on the A6xx parts.
It's now "smarter", needs a bit less register writes and controls more
things (like inter-frame power collapse) mostly internally (instead of
us having to write to G[PM]U_[CG]X registers from APPS)
The only difference worth mentioning is the now-required DEMET clock,
which is strictly required for things like asserting reset lines, not
turning it on results in GMU not being fully functional (all OOB requests
would fail and HFI would hang after the first submitted OOB).
Describe the A730 and A740 GMU.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # sm8450
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/559278/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Make it explicit that child nodes have additional properties and the
child node schema is not complete. The complete schemas are applied
separately based the compatible strings.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Patchwork: https://patchwork.freedesktop.org/patch/559387/
Link: https://lore.kernel.org/r/20230925212434.1972368-2-robh@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Just as unevaluatedProperties or additionalProperties are required at
the top level of schemas, they should (and will) also be required for
child node schemas. That ensures only documented properties are
present for any node.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Patchwork: https://patchwork.freedesktop.org/patch/559385/
Link: https://lore.kernel.org/r/20230925212434.1972368-1-robh@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
fsl,imx6-hdmi.yaml makes a reference to synopsys,dw-hdmi.yaml.
The 'interrupts' and 'reg' properties are described in synopsys,dw-hdmi.yaml,
so use 'unevaluatedProperties: false' so that these two properties can
be accepted.
This fixes the following schema warnings:
hdmi@120000: 'interrupts', 'reg' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/imx/fsl,imx6-hdmi.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230930130102.798822-1-festevam@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
drm-misc-next for v6.7-rc1:
UAPI Changes:
- drm_file owner is now updated during use, in the case of a drm fd
opened by the display server for a client, the correct owner is
displayed.
- Qaic gains support for the QAIC_DETACH_SLICE_BO ioctl to allow bo
recycling.
Cross-subsystem Changes:
- Disable boot logo for au1200fb, mmpfb and unexport logo helpers.
Only fbcon should manage display of logo.
- Update freescale in MAINTAINERS.
- Add some bridge files to bridge in MAINTAINERS.
- Update gma500 driver repo in MAINTAINERS to point to drm-misc.
Core Changes:
- Move size computations to drm buddy allocator.
- Make drm_atomic_helper_shutdown(NULL) a nop.
- Assorted small fixes in drm_debugfs, DP-MST payload addition error handling.
- Fix DRM_BRIDGE_ATTACH_NO_CONNECTOR handling.
- Handle bad (h/v)sync_end in EDID by clipping to htotal.
- Build GPUVM as a module.
Driver Changes:
- Simple drivers don't need to cache prepared result.
- Call drm_atomic_helper_shutdown() in shutdown/unbind for a whole lot
more drm drivers.
- Assorted small fixes in amdgpu, ssd130x, bridge/it6621, accel/qaic,
nouveau, tc358768.
- Add NV12 for komeda writeback.
- Add arbitration lost event to synopsis/dw-hdmi-cec.
- Speed up s/r in nouveau by not restoring some big bo's.
- Assorted nouveau display rework in preparation for GSP-RM,
especially related to how the modeset sequence works and
the DP sequence in relation to link training.
- Update anx7816 panel.
- Support NVSYNC and NHSYNC in tegra.
- Allow multiple power domains in simple driver.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f1fae5eb-25b8-192a-9a53-215e1184ce81@linux.intel.com
To complement panel-simple.yaml, create panel-simple-lvds-dual-ports.yaml.
panel-simple-lvds-dual-ports.yaml is for all simple LVDS panels that
have dual LVDS ports and require only a single power-supply.
The first port receives odd pixels, and the second port receives even pixels.
Optionally, a backlight and an enable GPIO can be specified as properties.
Panels with swapped pixel order, if any, need dedicated bindings.
Migrate 'auo,g133han01', 'auo,g185han01', 'auo,g190ean01',
'koe,tx26d202vm0bwa' and 'nlt,nl192108ac18-02d' over to the new file.
The objectives with one file for all the simple LVDS panels with dual ports are:
- Make it simpler to add bindings for this kind of LVDS panels
- Keep the number of bindings file lower
- Keep the binding documentation for this kind of LVDS panels more consistent
- Make it possible for drivers to get pixel order via
drm_of_lvds_get_dual_link_pixel_order(), as the 'ports' property is required
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1613017672-2734-1-git-send-email-victor.liu@nxp.com
Signed-off-by: Rob Herring <robh@kernel.org>
Add dt-binding documentation of dp-tx for MediaTek MT8188 SoC.
Signed-off-by: Shuijing Li <shuijing.li@mediatek.com>
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230822024155.26670-2-shuijing.li@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
drm-misc-next for v6.7-rc1:
UAPI Changes:
- Nouveau changed to not set NO_PREFETCH flag explicitly.
Cross-subsystem Changes:
- Update documentation of dma-buf intro and uapi.
- fbdev/sbus fixes.
- Use initializer macros in a lot of fbdev drivers.
- Add Boris Brezillon as Panfrost driver maintainer.
- Add Jessica Zhang as drm/panel reviewer.
- Make more fbdev drivers use fb_ops helpers for deferred io.
- Small hid trailing whitespace fix.
- Use fb_ops in hid/picolcd
Core Changes:
- Assorted small fixes to ttm tests, drm/mst.
- Documentation updates to bridge.
- Add kunit tests for some drm_fb functions.
- Rework drm_debugfs implementation.
- Update xe documentation to mark todos as completed.
Driver Changes:
- Add support to rockchip for rv1126 mipi-dsi and vop.
- Assorted small fixes to nouveau, bridge/samsung-dsim,
bridge/lvds-codec, loongson, rockchip, panfrost, gma500, repaper,
komeda, virtio, ssd130x.
- Add support for simple panels Mitsubishi AA084XE01,
JDI LPM102A188A,
- Documentation updates to accel/ivpu.
- Some nouveau scheduling/fence fixes.
- Power management related fixes and other fixes to ivpu.
- Assorted bridge/it66121 fixes.
- Make platform drivers return void in remove() callback.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3da6554b-3b47-fe7d-c4ea-21f4f819dbb6@linux.intel.com
As requested by Robert Foss <rfoss@kernel.org>, this patch adds
definition for anx7816. It supplements the patch submitted to dri-devel.
Signed-off-by: Alicja Michalska <ahplka19@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/ZQjFabKW7QvrvsnG@tora
Add dt-binding documentation of dsi for MediaTek MT8188 SoC.
Signed-off-by: Shuijing Li <shuijing.li@mediatek.com>
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230911120800.17369-2-shuijing.li@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
DT core:
- Add support for generating DT nodes for PCI devices. This is the
groundwork for applying overlays to PCI devices containing
non-discoverable downstream devices.
- DT unittest additions to check reverted changesets, to test for
refcount issues, and to test unresolved symbols. Also, various
clean-ups of the unittest along the way.
- Refactor node and property manipulation functions to better share code
with old API and changeset API
- Refactor changeset print functions to a common implementation
- Move some platform_device specific functions into of_platform.c
Bindings:
- Treewide fixing of typos
- Treewide clean-up of SPDX tags to use 'OR' consistently
- Last chunk of dropping unnecessary quotes. With that, the check
for unnecessary quotes is enabled in yamllint.
- Convert ftgmac100, zynqmp-genpd, pps-gpio, syna,rmi4, and qcom,ssbi
bindings to DT schema format
- Add Allwinner V3s xHCI USB, Saef SF-TC154B display, QCom SM8450 Inline
Crypto Engine, QCom SM6115 UFS, QCom SDM670 PDC interrupt controller,
Arm 2022 Cortex cores, and QCom IPQ9574 Crypto bindings
- Fixes for Rockchip DWC PCI binding
- Ensure all properties are evaluated on USB connector schema
- Fix dt-check-compatible script to find of_device_id instances with
compiler annotations
-----BEGIN PGP SIGNATURE-----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=kl+z
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DT core:
- Add support for generating DT nodes for PCI devices. This is the
groundwork for applying overlays to PCI devices containing
non-discoverable downstream devices.
- DT unittest additions to check reverted changesets, to test for
refcount issues, and to test unresolved symbols. Also, various
clean-ups of the unittest along the way.
- Refactor node and property manipulation functions to better share
code with old API and changeset API
- Refactor changeset print functions to a common implementation
- Move some platform_device specific functions into of_platform.c
Bindings:
- Treewide fixing of typos
- Treewide clean-up of SPDX tags to use 'OR' consistently
- Last chunk of dropping unnecessary quotes. With that, the check for
unnecessary quotes is enabled in yamllint.
- Convert ftgmac100, zynqmp-genpd, pps-gpio, syna,rmi4, and qcom,ssbi
bindings to DT schema format
- Add Allwinner V3s xHCI USB, Saef SF-TC154B display, QCom SM8450
Inline Crypto Engine, QCom SM6115 UFS, QCom SDM670 PDC interrupt
controller, Arm 2022 Cortex cores, and QCom IPQ9574 Crypto bindings
- Fixes for Rockchip DWC PCI binding
- Ensure all properties are evaluated on USB connector schema
- Fix dt-check-compatible script to find of_device_id instances with
compiler annotations"
* tag 'devicetree-for-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (64 commits)
dt-bindings: usb: Add V3s compatible string for OHCI
dt-bindings: usb: Add V3s compatible string for EHCI
dt-bindings: display: panel: mipi-dbi-spi: add Saef SF-TC154B
dt-bindings: vendor-prefixes: document Saef Technology
dt-bindings: thermal: lmh: update maintainer address
of: unittest: Fix of_unittest_pci_node() kconfig dependencies
dt-bindings: crypto: ice: Document sm8450 inline crypto engine
dt-bindings: ufs: qcom: Add ICE to sm8450 example
dt-bindings: ufs: qcom: Add sm6115 binding
dt-bindings: ufs: qcom: Add reg-names property for ICE
dt-bindings: yamllint: Enable quoted string check
dt-bindings: Drop remaining unneeded quotes
of: unittest-data: Fix whitespace - angular brackets
of: unittest-data: Fix whitespace - indentation
of: unittest-data: Fix whitespace - blank lines
of: unittest-data: Convert remaining overlay DTS files to sugar syntax
of: overlay: unittest: Add test for unresolved symbol
of: unittest: Add separators to of_unittest_overlay_high_level()
of: unittest: Cleanup partially-applied overlays
of: unittest: Merge of_unittest_apply{,_revert}_overlay_check()
...
The main change this time is the introduction of the drivers/genpd
subsystem that gets split out from drivers/soc to keep common
functionality together. Ulf Hansson is taking over maintainership for
these and is sending a separate pull request with the same commits,
but they are in the soc drivers tree to avoid conflicts against other
soc driver patches.
The SCMI driver subsystem gets an update to version 3.2 of the
specification. There are also updates to memory, reset and other firmware
drivers.
On the soc driver side, the updates are mostly cleanups across a number
of Arm platforms. On driver for loongarch adds power management for DT
based systems, another driver is for HiSilicon's Arm server chips with
their HCCS system health interface.
The remaining updates for the most part add support for additional
hardware in existing drivers or contain minor cleanups. Most of these
are for the Qualcomm Snapdragon platform.
-----BEGIN PGP SIGNATURE-----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=xmHW
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The main change this time was the introduction of the drivers/genpd
subsystem that gets split out from drivers/soc to keep common
functionality together.
The SCMI driver subsystem gets an update to version 3.2 of the
specification. There are also updates to memory, reset and other
firmware drivers.
On the soc driver side, the updates are mostly cleanups across a
number of Arm platforms. On driver for loongarch adds power management
for DT based systems, another driver is for HiSilicon's Arm server
chips with their HCCS system health interface.
The remaining updates for the most part add support for additional
hardware in existing drivers or contain minor cleanups. Most of these
are for the Qualcomm Snapdragon platform"
* tag 'soc-drivers-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (136 commits)
bus: fsl-mc: Use common ranges functions
soc: kunpeng_hccs: fix some sparse warnings about incorrect type
soc: loongson2_pm: add power management support
soc: dt-bindings: add loongson-2 pm
soc: rockchip: grf: Fix SDMMC not working on RK3588 with bus-width > 1
genpd: rockchip: Add PD_VO entry for rv1126
bus: ti-sysc: Fix cast to enum warning
soc: kunpeng_hccs: add MAILBOX dependency
MAINTAINERS: remove OXNAS entry
dt-bindings: interrupt-controller: arm,versatile-fpga-irq: mark oxnas compatible as deprecated
irqchip: irq-versatile-fpga: remove obsolete oxnas compatible
soc: qcom: aoss: Tidy up qmp_send() callers
soc: qcom: aoss: Format string in qmp_send()
soc: qcom: aoss: Move length requirements from caller
soc: kunpeng_hccs: fix size_t format string
soc: ti: k3-socinfo.c: Add JTAG ID for AM62PX
dt-bindings: firmware: qcom: scm: Updating VMID list
firmware: imx: scu-irq: support identifying SCU wakeup source from sysfs
firmware: imx: scu-irq: enlarge the IMX_SC_IRQ_NUM_GROUP
firmware: imx: scu-irq: add imx_scu_irq_get_status
...
Updates for v6.6, which includes a backmerge of msm-fixes to avoid conficts.
Core:
- SM6125 MDSS support
DPU:
- SM6125 DPU support
- Added subblocks to display snapshot
- Use UBWC data from MDSS driver rather than duplicating it
- dpu_core_perf cleanup
DSI:
- Enabled burst mode to fix CMD mode panels
- Runtime PM support
- refgen regulator support
DSI PHY:
- SM6125 support in 14nm DSI PHY driver
GPU:
- Rework GPU identification to prepare for a7xx, and other a7xx prep
- Cleanups and fixes
- Disallow legacy relocs on a6xx and newer
- a690: switch to using a660_gmu.bin fw as this is what we have in
linux-firmware and we see no evidence that it should be different
from other a660 family (a6xx subgen 4) devices
- Submit overhead opts, 1.6x faster for NO_IMPLICIT_SYNC commits with
100 BOs to 2.5x faster for 1000 BOs
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGv_01g-edjdfKLWWcb-rO5aSyLsv5FpbKrTkXVL9+ngTQ@mail.gmail.com
Documentation/process/license-rules.rst and checkpatch expect the SPDX
identifier syntax for multiple licenses to use capital "OR". Correct it
to keep consistent format and avoid copy-paste issues.
Correct also the format // -> .* in few Allwinner binding headers as
pointed out by checkpatch:
WARNING: Improper SPDX comment style for 'include/dt-bindings/reset/sun50i-h6-ccu.h', please use '/*' instead
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230823084540.112602-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Simple 'opp-table:true' accepts a boolean property as opp-table, so
restrict it to object to properly enforce real OPP table nodes.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230820080543.25204-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Fix typos in Documentation/devicetree/bindings. The changes are in
descriptions or comments where they shouldn't affect functionality.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20230814212822.193684-3-helgaas@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
The VOP on Rockchip's RV1126 SoC is different from other SoC's
VOP implementations, so add a separate compatible for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230731110012.2913742-6-jagan@edgeble.ai
The sitronix-st7789v driver now considers the rotation property.
Add the property to the documentation.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230718-feature-st7789v-v3-3-157d68fb63e2@wolfvision.net
Add and document the reserved memory region property in the
mdss-common schema.
For now (sdm845-db845c), it points to a framebuffer memory
region reserved by the bootloader for splash screen.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/549376/
Link: https://lore.kernel.org/r/20230726132719.2117369-1-amit.pundir@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The ST7789V LCD controller supports regular SPI wiring, as well as no Rx
data line at all. The operating system needs to know whether it can read
registers from the device or not. Let's detail this specific design
possibility by bounding the spi-rx-bus-width property.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-16-sre@kernel.org
The ST7789V LCD controller is also embedded in the ET028013DMA
panel. Add a compatible string to describe this other panel.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-15-sre@kernel.org
Add compatible value for Inanbo t28cp45tn89 and make reset GPIO non
mandatory, since it might not be connected to the CPU.
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-3-sre@kernel.org
The Hydis HV070WX2-1E0 is a 7" WXGA (800x1280) TFT LCD LVDS panel that
is one of the variants used on Google Nexus 7.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230726185010.2294709-2-thierry.reding@gmail.com
The Chunghwa CLAA070WP03XG is an LVDS panel, so move it to the correct
bindings file.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230726185010.2294709-1-thierry.reding@gmail.com
The HannStar HSD101PWW2 is an LVDS panel, so move it to the correct
bindings file.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230726184857.2294570-1-thierry.reding@gmail.com
Document availability of the 14nm DSI PHY on SM6125. Note that this
compatible uses the SoC-suffix variant, intead of postfixing an
arbitrary number without the sm/sdm portion. The PHY is not powered by
a vcca regulator like on most SoCs, but by the MX power domain that is
provided via the power-domains property and a single corresponding
required-opps.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/548979/
Link: https://lore.kernel.org/r/20230723-sm6125-dpu-v4-12-a3f287dd6c07@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
SM6125 is identical to SM6375 including the throttle clock that is also
provided to the MDP node downstream. Note that any SoC other than
SM6375 (currently SC7180 and SM6350) has an unconstrained maximum number
of clocks and could either pass or leave out this "throttle" clock.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/548972/
Link: https://lore.kernel.org/r/20230723-sm6125-dpu-v4-8-a3f287dd6c07@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Both SM6350 and SM6375 support only a single DSI link, and don't have a
corresponding dsi1 node in DTS. Their examples should not suggest an
output interface port on the display-controller node to this inexistant
DSI host, with a dsi1_in label reference that doesn't exist in the
example either.
Fixes: 3b7502b0c2 ("dt-bindings: display/msm: Add SM6350 MDSS")
Fixes: 2a5c1021bc ("dt-bindings: display/msm: Add SM6375 MDSS")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Acked-by: Rob Herring <robh@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/548961/
Link: https://lore.kernel.org/r/20230723-sm6125-dpu-v4-4-a3f287dd6c07@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
UAPI Changes:
* fbdev:
* Make fbdev userspace interfaces optional; only leaves the
framebuffer console active
* prime:
* Support dma-buf self-import for all drivers automatically: improves
support for many userspace compositors
Cross-subsystem Changes:
* backlight:
* Fix interaction with fbdev in several drivers
* base: Convert struct platform.remove to return void; part of a larger,
tree-wide effort
* dma-buf: Acquire reservation lock for mmap() in exporters; part
of an on-going effort to simplify locking around dma-bufs
* fbdev:
* Use Linux device instead of fbdev device in many places
* Use deferred-I/O helper macros in various drivers
* i2c: Convert struct i2c from .probe_new to .probe; part of a larger,
tree-wide effort
* video:
* Avoid including <linux/screen_info.h>
Core Changes:
* atomic:
* Improve logging
* prime:
* Remove struct drm_driver.gem_prime_mmap plus driver updates: all
drivers now implement this callback with drm_gem_prime_mmap()
* gem:
* Support execution contexts: provides locking over multiple GEM
objects
* ttm:
* Support init_on_free
* Swapout fixes
Driver Changes:
* accel:
* ivpu: MMU updates; Support debugfs
* ast:
* Improve device-model detection
* Cleanups
* bridge:
* dw-hdmi: Improve support for YUV420 bus format
* dw-mipi-dsi: Fix enable/disable of DSI controller
* lt9611uxc: Use MODULE_FIRMWARE()
* ps8640: Remove broken EDID code
* samsung-dsim: Fix command transfer
* tc358764: Handle HS/VS polarity; Use BIT() macro; Various cleanups
* Cleanups
* ingenic:
* Kconfig REGMAP fixes
* loongson:
* Support display controller
* mgag200:
* Minor fixes
* mxsfb:
* Support disabling overlay planes
* nouveau:
* Improve VRAM detection
* Various fixes and cleanups
* panel:
* panel-edp: Support AUO B116XAB01.4
* Support Visionox R66451 plus DT bindings
* Cleanups
* ssd130x:
* Support per-controller default resolution plus DT bindings
* Reduce memory-allocation overhead
* Cleanups
* tidss:
* Support TI AM625 plus DT bindings
* Implement new connector model plus driver updates
* vkms
* Improve write-back support
* Documentation fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAmSvvRAACgkQaA3BHVML
eiNpGQgAs8jq1XjN9t8jZsdgXnoCbkZyVUI2NO0HwoVwpRCLgbXp5AX5qq2oRciE
TBhe4Fceh/ZsYqHTZQahnguxgRKM5JgXwbI4Z0iiOVcqasNbycaKAqipxJJ7kdo1
qPhGCbgQFVX7oIq2xjfXehh6O0SYX+R9r88X8dMJxMYv/pcLwOHG74kS040WOcQq
uATgcnobOf/D8ZmlqvfKGAeTUoFo/RSR2Uhlauka58qgeUbicrTELZT2barY9d+k
as6U5vv4wx2zMklTkjrlkMpAT1ZpbB9d3jGHwL27VEnjlfd3wV2bdH7Dzn9qZRf/
gn0ALg/b3u5yBWk/k7YBvijXyNcH6Q==
=bBuG
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2023-07-13' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.6:
UAPI Changes:
* fbdev:
* Make fbdev userspace interfaces optional; only leaves the
framebuffer console active
* prime:
* Support dma-buf self-import for all drivers automatically: improves
support for many userspace compositors
Cross-subsystem Changes:
* backlight:
* Fix interaction with fbdev in several drivers
* base: Convert struct platform.remove to return void; part of a larger,
tree-wide effort
* dma-buf: Acquire reservation lock for mmap() in exporters; part
of an on-going effort to simplify locking around dma-bufs
* fbdev:
* Use Linux device instead of fbdev device in many places
* Use deferred-I/O helper macros in various drivers
* i2c: Convert struct i2c from .probe_new to .probe; part of a larger,
tree-wide effort
* video:
* Avoid including <linux/screen_info.h>
Core Changes:
* atomic:
* Improve logging
* prime:
* Remove struct drm_driver.gem_prime_mmap plus driver updates: all
drivers now implement this callback with drm_gem_prime_mmap()
* gem:
* Support execution contexts: provides locking over multiple GEM
objects
* ttm:
* Support init_on_free
* Swapout fixes
Driver Changes:
* accel:
* ivpu: MMU updates; Support debugfs
* ast:
* Improve device-model detection
* Cleanups
* bridge:
* dw-hdmi: Improve support for YUV420 bus format
* dw-mipi-dsi: Fix enable/disable of DSI controller
* lt9611uxc: Use MODULE_FIRMWARE()
* ps8640: Remove broken EDID code
* samsung-dsim: Fix command transfer
* tc358764: Handle HS/VS polarity; Use BIT() macro; Various cleanups
* Cleanups
* ingenic:
* Kconfig REGMAP fixes
* loongson:
* Support display controller
* mgag200:
* Minor fixes
* mxsfb:
* Support disabling overlay planes
* nouveau:
* Improve VRAM detection
* Various fixes and cleanups
* panel:
* panel-edp: Support AUO B116XAB01.4
* Support Visionox R66451 plus DT bindings
* Cleanups
* ssd130x:
* Support per-controller default resolution plus DT bindings
* Reduce memory-allocation overhead
* Cleanups
* tidss:
* Support TI AM625 plus DT bindings
* Implement new connector model plus driver updates
* vkms
* Improve write-back support
* Documentation fixes
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230713090830.GA23281@linux-uq9g
- Whitespace clean-ups in binding examples
- Restrict node name suffixes to "-[0-9]+" for cases of multiple
instances which don't have unit-addresses
- Convert brcm,kona-wdt and cdns,wdt-r1p2 watchdog bindings to DT schema
-----BEGIN PGP SIGNATURE-----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=cRW/
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-6.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull more devicetree updates from Rob Herring:
- Whitespace clean-ups in binding examples
- Restrict node name suffixes to "-[0-9]+" for cases of multiple
instances which don't have unit-addresses
- Convert brcm,kona-wdt and cdns,wdt-r1p2 watchdog bindings to DT
schema
* tag 'devicetree-for-6.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: soc: qcom: stats: Update maintainer email
dt-bindings: cleanup DTS example whitespaces
dt-bindings: timestamp: restrict node name suffixes
dt-bindings: slimbus: restrict node name suffixes
dt-bindings: watchdog: restrict node name suffixes
dt-bindings: watchdog: brcm,kona-wdt: convert txt file to yaml
dt-bindings: watchdog: cdns,wdt-r1p2: Convert cadence watchdog to yaml
-----BEGIN PGP SIGNATURE-----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=YwIy
-----END PGP SIGNATURE-----
Merge tag 'media/v6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Lots of improvement at atomisp driver, which is starting to look in
good shape
- Mediatek vcodec driver has gained support for av1 and hevc stateless
codecs
- New sensor driver: ov01a10
- verisilicon driver has gained AV1 entropy helpers
- tegra-video has gained support for Tegra20 parallel input
- dvb core has gained an extra property to better support DVB-S2X
- as usual, lots of cleanups, fixes and improvements on media drivers
* tag 'media/v6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (253 commits)
media: wl128x: fix a clang warning
media: dvb: mb86a20s: get rid of a clang-15 warning
media: cec: i2c: ch7322: also select REGMAP
media: add HAS_IOPORT dependencies
media: tc358746: select CONFIG_GENERIC_PHY
media: mediatek: vcodec: Add dbgfs help function
media: mediatek: vcodec: Add encode to support dbgfs
media: mediatek: vcodec: Change dbgfs interface to support encode
media: mediatek: vcodec: Get each instance format type
media: mediatek: vcodec: Get each context resolution information
media: mediatek: vcodec: Add a debugfs file to get different useful information
media: mediatek: vcodec: Add debug params to control different log level
media: mediatek: vcodec: Add debugfs interface to get debug information
media: mediatek: vcodec: support stateless AV1 decoder
media: verisilicon: Conditionally ignore native formats
media: verisilicon: Enable AV1 decoder on rk3588
media: verisilicon: Add film grain feature to AV1 driver
media: verisilicon: Add Rockchip AV1 decoder
media: verisilicon: Add AV1 entropy helpers
media: verisilicon: Compute motion vectors size for AV1 frames
...
The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for each
SoC vendor, following the same scheme that is used on arm64, mips and
riscv. This has been discussed for many years, but so far we never did
this as there was a plan to move the files out of the kernel entirely,
which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along
with their device drivers.
* The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the time.
* Amlogic C3 is a Cortex-A35 based smart IP camera chip
* Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
* Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
* Qualcomm SDX75 is the latest generation modem chip that is used
as a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
* Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the Xuantie
C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those included
there are 39 new board files, but only five more 32-bit this time, probably
a new low:
* Marantec Maveo board based on dhcor imx6ull module
* Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
* Epson Moverio BT-200 AR glasses based on TI OMAP4
* PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
* ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than
we had in the recent releases:
* Three boards based on NXP i.MX8: Emtop SoM & Baseboard,
NXP i.MX8MM EVKB board and i.MX8MP based Gateworks Venice
gw7905-2x device.
* NVIDIA IGX Orin and Jetson Orin Nano boards, both based on
tegra234
* Qualcomm gains support for 6 reference boards on various members
of their IPQ networking SoC series, as well as the Sony Xperia M4
Aqua phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board
on top of the various reference platforms for their new chips.
* Rockchips support for several newer boards: Indiedroid Nova (rk3588),
Edgeble Neural Compute Module 6B (rk3588), FriendlyARM NanoPi R2C
Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn Fastrhino R66S/R68S
(rk3568)
* TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex Verdin
family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
* continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
* support for devicetree overlays on at91, bcm283x
* significant additions to existing SoC support on mediatek, qualcomm,
ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST STM32MP1
As usual, a lot more detail is available in the individual merge
commits.
-----BEGIN PGP SIGNATURE-----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=X/KE
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for
each SoC vendor, following the same scheme that is used on arm64, mips
and riscv. This has been discussed for many years, but so far we never
did this as there was a plan to move the files out of the kernel
entirely, which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along with
their device drivers.
- The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the
time.
- Amlogic C3 is a Cortex-A35 based smart IP camera chip
- Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
- Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
- Qualcomm SDX75 is the latest generation modem chip that is used as
a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
- Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
Xuantie C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those
included there are 39 new board files, but only five more 32-bit this
time, probably a new low:
- Marantec Maveo board based on dhcor imx6ull module
- Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
- Epson Moverio BT-200 AR glasses based on TI OMAP4
- PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
- ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than we had
in the recent releases:
- Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.
- NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234
- Qualcomm gains support for 6 reference boards on various members of
their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
of the various reference platforms for their new chips.
- Rockchips support for several newer boards: Indiedroid Nova
(rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
Fastrhino R66S/R68S (rk3568)
- TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
Verdin family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
- continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
- support for devicetree overlays on at91, bcm283x
- significant additions to existing SoC support on mediatek,
qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
STM32MP1
As usual, a lot more detail is available in the individual merge
commits"
* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
ARM: mvebu: fix unit address on armada-390-db flash
ARM: dts: Move .dts files to vendor sub-directories
kbuild: Support flat DTBs install
ARM: dts: Add .dts files missing from the build
ARM: dts: allwinner: Use quoted #include
ARM: dts: lan966x: kontron-d10: add PHY interrupts
ARM: dts: lan966x: kontron-d10: fix SPI CS
ARM: dts: lan966x: kontron-d10: fix board reset
ARM: dts: at91: Enable device-tree overlay support for AT91 boards
arm: dts: Enable device-tree overlay support for AT91 boards
arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
ARM: dts: at91: use generic name for shutdown controller
ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
dt-bindings: firmware: brcm,kona-smc: convert to YAML
riscv: dts: sort makefile entries by directory
riscv: defconfig: enable T-HEAD SoC
MAINTAINERS: add entry for T-HEAD RISC-V SoC
riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
riscv: dts: add initial T-HEAD TH1520 SoC device tree
riscv: Add the T-HEAD SoC family Kconfig option
...
Bindings:
- Add some missing type definitions to properties
- Drop unneeded quotes and use absolute paths in bindings
- Remove redundant "binding" or "schema" in binding titles
- Add bindings for Ralink SoCs interrupt controller, QCA2066 Bluetooth,
infineon,irps5401, new NXP i.MX GPT variants, shineworld lh133k MIPI
SPI panel, Socionext Synquacer platforms, RK3588 PCIe, ST M95640
EEPROM, and FSL DCP crypto variants, and Arm Cortex-R52
DT core:
- Improve the reserved-memory range allocation to maximize contiguous
space
- Use device_set_node() helper in place of open coding
-----BEGIN PGP SIGNATURE-----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=onek
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"Bindings:
- Add some missing type definitions to properties
- Drop unneeded quotes and use absolute paths in bindings
- Remove redundant "binding" or "schema" in binding titles
- Add bindings for Ralink SoCs interrupt controller, QCA2066
Bluetooth, infineon,irps5401, new NXP i.MX GPT variants, shineworld
lh133k MIPI SPI panel, Socionext Synquacer platforms, RK3588 PCIe,
ST M95640 EEPROM, and FSL DCP crypto variants, and Arm Cortex-R52
DT core:
- Improve the reserved-memory range allocation to maximize contiguous
space
- Use device_set_node() helper in place of open coding"
* tag 'devicetree-for-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (40 commits)
dt-bindings: interrupt-controller: add Ralink SoCs interrupt controller
dt-bindings: PCI: dwc: rockchip: Update for RK3588
dt-bindings: auxdisplay: holtek: Add missing type for "linux,no-autorepeat"
dt-bindings: input: mediatek,pmic-keys: Fix typo in "linux,keycodes" property name
dt-bindings: pwm: drop unneeded quotes
dt-bindings: crypto: drop unneeded quotes
dt-bindings: arm: socionext: add Synquacer platforms
dt-bindings: connector: usb: allow a single HS port
dt-bindings: bus: ti-sysc: fix typo
of: reserved_mem: Use stable allocation order
of: reserved_mem: Try to keep range allocations contiguous
dt-bindings: arm: drop unneeded quotes and use absolute /schemas path
dt-bindings: firmware: arm,scmi: drop unneeded quotes and use absolute /schemas path
dt-bindings: dvfs: drop unneeded quotes
dt-bindings: gpu: drop unneeded quotes
dt-bindings: i3c: silvaco,i3c-master: drop unneeded quotes
dt-bindings: rockchip: grf: drop unneeded quotes
dt-bindings: spmi: mtk,spmi-mtk-pmif: drop unneeded quotes
dt-bindings: Remove last usage of "binding" or "schema" in titles
dt-bindings: display: panel: mipi-dbi-spi: add spi-3wire property
...
Highlights:
----------
- MCU/MPU:
- Replace deprecated st,hw-flow-ctrl by uart-has-rtscts.
- Fix LTDC/DSI warnings.
- MPU:
- STMP32MP15:
- Add OTP part number and Vrefint calibration in bsec.
- M4 hold management updated. As SMC call is deprecated,
the service is moved on a SCMI service.
- Add ADC internal channels (VREFINT/VDDCORE).
- ST:
- Enable ADC1&2 on STM32MP15 DKx boards.
- Adopt generic IIO bindings on STM32MP157C ED1
- Add supplies for OV5640 in STM32MP157C EV1
to fix yaml validation.
- Fix i2s bindings to match with the YAML validation (DKx boards).
- DH:
- Rearrange MAC EEPROM.
- Rename AV96 sound card.
- Adopt generic IIo bindings.
- Fix audio routing.
-PHYTEC:
- Add PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM.
This SOM embeds up to 1GB DDR3LP RAM, up to 1GB eMMC,
up to 16 MB QSPI and up to 128 GB NAND flash.
-----BEGIN PGP SIGNATURE-----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=kf1Q
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmSSDJoACgkQYKtH/8kJ
Uif9qxAAnrSnL55CNXoWGiGjhyZxw4Vscm1cBYlSHINoH4wdumRteV3Ux74SCsyy
rlny5kIi2g5Le/EXYA0cH4GbEtXUzm+xyrPGUM7M67AStIE3es51OCoOS4JBYw34
jv82s+rzuXUTogruS5EhkZ6NDve2Oo+sPIjdJWKhf/kV90uocrsQt7AwYs9MSs0t
cr46LaTUqXIHYyig8TbW7bNYqZTKn+0xCLo5DSeToru1dhBNraNkATapGglv7P1q
tcVexjf0SpsST8K7AW0R796urxrSCLBw3bFLqGodArs5N76RObcBLWasVqZPEC8q
Uy2JAyiNGWzSPjAznUBnllCndxOd+0wqSKYkffR8jjSpYvcL0aoqi8F+Lqa+C/Dv
I2SHA2JhAwYdKj5Zc9SGFuVcwb7ABNBi4uimjm9rwlYmKHeHzFrIh5pcROpPi3qe
4/8YNjyx5LyvZ7su+GFGhLAi7XmhtJ7j07BuRfMJJcOdw6AxOvzvNxIZvmNN8evV
U9r6/NXJaLw4SmhhlXTTatWnU/oxx8GvXja/tFfReotFuefBjwYYhhsjRcebtaXr
RFEtCjtauVHdQRxsJbeuCZ56l5Sjliqg4EJ5AuOEpXf4s4Z98ZEoO5KPWWTFlwjp
Th2zLU3pbJPqbQcp9lxN+ETBemuYhr97XrNmFpitec7kTjl/hTM=
=kRKO
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into soc/dt
STM32 DT for v6.5, round 1
Highlights:
----------
- MCU/MPU:
- Replace deprecated st,hw-flow-ctrl by uart-has-rtscts.
- Fix LTDC/DSI warnings.
- MPU:
- STMP32MP15:
- Add OTP part number and Vrefint calibration in bsec.
- M4 hold management updated. As SMC call is deprecated,
the service is moved on a SCMI service.
- Add ADC internal channels (VREFINT/VDDCORE).
- ST:
- Enable ADC1&2 on STM32MP15 DKx boards.
- Adopt generic IIO bindings on STM32MP157C ED1
- Add supplies for OV5640 in STM32MP157C EV1
to fix yaml validation.
- Fix i2s bindings to match with the YAML validation (DKx boards).
- DH:
- Rearrange MAC EEPROM.
- Rename AV96 sound card.
- Adopt generic IIo bindings.
- Fix audio routing.
-PHYTEC:
- Add PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM.
This SOM embeds up to 1GB DDR3LP RAM, up to 1GB eMMC,
up to 16 MB QSPI and up to 128 GB NAND flash.
* tag 'stm32-dt-for-v6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (34 commits)
ARM: dts: stm32: fix i2s endpoint format property for stm32mp15xx-dkx
ARM: dts: stm32: Fix audio routing on STM32MP15xx DHCOM PDK2
ARM: dts: stm32: add required supplies of ov5640 in stm32mp157c-ev1
ARM: dts: stm32: Update to generic ADC channel binding on DHSOM systems
ARM: dts: stm32: adopt generic iio bindings for adc channels on dhcor-testbench
ARM: dts: stm32: adopt generic iio bindings for adc channels on dhcor-drc
ARM: dts: stm32: adopt generic iio bindings for adc channels on emstamp-argon
ARM: dts: stm32: adopt generic iio bindings for adc channels on stm32mp157c-ed1
ARM: dts: stm32: enable adc on stm32mp15xx-dkx boards
ARM: dts: stm32: add vrefint support to adc2 on stm32mp15
ARM: dts: stm32: add vrefint calibration on stm32mp15
ARM: dts: stm32: add adc internal channels to stm32mp15
ARM: dts: stm32: fix ltdc warnings in stm32mp15 boards
ARM: dts: stm32: fix dsi warnings on stm32mp15 boards
dt-bindings: display: st,stm32-dsi: Remove unnecessary fields
ARM: dts: stm32: fix warnings on stm32f469-disco board
ARM: dts: stm32: Shorten the AV96 HDMI sound card name
ARM: dts: stm32: fix m4_rproc references to use SCMI for stm32mp15
ARM: dts: stm32: Update Cortex-M4 reset declarations on stm32mp15
ARM: dts: stm32: add STM32MP1-based Phytec board
...
Link: https://lore.kernel.org/r/08d711de-bb6d-a976-735b-5e18b19818ea@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Backmerging into drm-misc-next to get commit 2c1c7ba457
("drm/amdgpu: support partition drm devices"), which is required to fix
commit 0adec22702 ("drm: Remove struct drm_driver.gem_prime_mmap").
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
The DSS controller on TI's AM625 SoC is an update from that on TI's
AM65X SoC. The former has an additional OLDI TX on its first video port
that helps output cloned video or WUXGA (1920x1200@60fps) resolution
video output over a dual-link mode to reduce the required OLDI clock
output.
The second video port is same from AM65x DSS and it outputs DPI video
data. It can support 2K resolutions @ 60fps, independently.
Add the new controller's compatible and update descriptions.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616150900.6617-2-a-bhatia1@ti.com
Updates for v6.5.. this includes a backmerg of drm-next tree to be able
to use new DRM DSC helpers.
Core:
+ Add Marijn Suijten as drm/msm reviewer
+ Adreno A660 bindings
+ SM8350 MDSS bindings fix
+ Fix adreno_is_a690() warnings
+ More generic (DRM) and MSM-specific DSC helpers
DP:
+ Removed obsolete USB-PD remains
+ Documented DP compatible string for sm8550 platform
DPU:
+ Enable missing features (DSPP, DSC, split display) on sc8180x,
sc8280xp, sm8450
+ Enabled writeback on sc7280
+ Implemented tearcheck support to support vsync on SM150 and
newer platforms
+ Native HDMI output support
+ Dropped unused features: regdma, GC, IGC
+ Fixed the DSC flush operations
+ Simplified QoS handling, removing obsolete and unused features
and merging SSPP and WB code paths
+ Reworked dpu_encoder initialisation path
+ Enabled DSPP support on sdm845
+ Disabled color-management if DSPP blocks are not available
+ Added support for DSC 1.2 blocks found on sm8350 and later
+ Added .fb_dirty to fix CMD panels
DSI:
+ Drop powerup quirks in favour of using pre_enable_prev_first for
downstream bridges
+ Fixed 14nm DSI PHY programming
+ Added support for DSI and 28nm DSI PHY on MSM8226 platform
+ Make use of DRM and MSM DSC helpers
MDP5:
+ Added support for display controller on MSM8226 platform
GPU:
+ A690 support
+ Don't set IO_PGTABLE_QUIRK_ARM_OUTER_WBWA on devices with coherent SMMU
(like A690)
+ Move cmdstream dumping out of fence signaling path
+ Cleanups
+ Support for a6xx devices without GMU (aka "GMU wrapper"
+ a610 support
+ a619_holi support (a619 variant without GMU)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGsUB=tRB4nR6ZCJMuLhro5zN3BQWUSywVYbaipqqDZ_cQ@mail.gmail.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmSPcdMeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGWrQH/3KmuvZsWMC4PpJY
VcF9VfF9i+Zv7DoG8sjD5VpNh47e87RsR6WNOFnKol5SUrM6vsBAb5i2rfQahNIv
NSj0fPCE4/Nj9LMecKVC9WD8CitxYdbR+CF9Is21AQj1VihUl9eHXGcAWxuaMyhk
TjPUwmbOOsRVMXXdGJzjX78cvLsxqpSv8A/5OTh16IBimbh7p+YjKJFkbfj/PMWf
aF1quFkIEXgzJcHCpP6KDZHr2KbpY+jIN9hUENnGKJxHYNso5u+KrIW1kAm8meP1
x26ETSquM0T70OAzovOWg+BeVkLDac/3Rh30ztLAI4AtajrlSzycvFsU9UNEJCc2
BnM2IZI=
=ANT5
-----END PGP SIGNATURE-----
Backmerge tag 'v6.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into drm-next
Linux 6.4-rc7
Need this to pull in the msm work.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The "GMU Wrapper" is Qualcomm's name for "let's treat the GPU blocks
we'd normally assign to the GMU as if they were a part of the GMU, even
though they are not". It's a (good) software representation of the GMU_CX
and GMU_GX register spaces within the GPUSS that helps us programatically
treat these de-facto GMU-less parts in a way that's very similar to their
GMU-equipped cousins, massively saving up on code duplication.
The "wrapper" register space was specifically designed to mimic the layout
of a real GMU, though it rather obviously does not have the M3 core et al.
To sum it all up, the GMU wrapper is essentially a register space within
the GPU, which Linux sees as a dumbed-down regular GMU: there's no clocks,
interrupts, multiple reg spaces, iommus and OPP. Document it.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542750/
Signed-off-by: Rob Clark <robdclark@chromium.org>
The "GMU Wrapper" is Qualcomm's name for "let's treat the GPU blocks
we'd normally assign to the GMU as if they were a part of the GMU, even
though they are not". It's a (good) software representation of the GMU_CX
and GMU_GX register spaces within the GPUSS that helps us programatically
treat these de-facto GMU-less parts in a way that's very similar to their
GMU-equipped cousins, massively saving up on code duplication.
The "wrapper" register space was specifically designed to mimic the layout
of a real GMU, though it rather obviously does not have the M3 core et al.
GMU wrapper-equipped A6xx GPUs require clocks and clock-names to be
specified under the GPU node, just like their older cousins. Account
for that.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542748/
Signed-off-by: Rob Clark <robdclark@chromium.org>
A default resolution in the ssd130x driver isn't set to an arbitrary 96x16
anymore. Instead is set to a width and height that's controller dependent.
The datasheets for the chips describes the following display resolutions:
- SH1106: 132 x 64 Dot Matrix OLED/PLED
- SSD1305: 132 x 64 Dot Matrix OLED/PLED
- SSD1306: 128 x 64 Dot Matrix OLED/PLED
- SSD1307: 128 x 39 Dot Matrix OLED/PLED
- SSD1309: 128 x 64 Dot Matrix OLED/PLED
Update DT schema to reflect what the driver does and make its users aware.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230609170941.1150941-3-javierm@redhat.com
Some MIPI DBI panels support a three wire mode (clock, chip select,
bidirectional data) that can be used to ask the panel if it is already set
up by e.g. the bootloader and can thus skip the initialization.
This enables a flicker-free boot.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://lore.kernel.org/r/20230614123222.4167460-4-l.goehrs@pengutronix.de
Signed-off-by: Rob Herring <robh@kernel.org>
The Shineworld LH133K is a 1.3" 240x240px RGB LCD with a MIPI DBI
compatible SPI interface.
The initialization procedure is quite basic with the exception of
requiring inverted colors.
A basic mipi-dbi-cmd[1] script to get the display running thus looks
like this:
$ cat shineworld,lh133k.txt
command 0x11 # exit sleep mode
delay 120
# The display seems to require display color inversion, so enable it.
command 0x21 # INVON
# Enable normal display mode (in contrast to partial display mode).
command 0x13 # NORON
command 0x29 # MIPI_DCS_SET_DISPLAY_ON
$ mipi-dbi-cmd shineworld,lh133k.bin shineworld,lh133k.txt
[1]: https://github.com/notro/panel-mipi-dbi
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://lore.kernel.org/r/20230614123222.4167460-3-l.goehrs@pengutronix.de
Signed-off-by: Rob Herring <robh@kernel.org>
A couple of display bridge properties are missing a type definition. Add
the types to them.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230613201114.2824626-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Merge the drm-next tree to pick up the DRM DSC helpers (merged via
drm-intel-next tree). MSM DSC v1.2 patches depend on these helpers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add a compatible string for MediaTek Helio X10 MT6795's OverDrive (OD)
block: this is the same as MT8173.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230412112739.160376-15-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add a compatible string for MediaTek Helio X10 MT6795: similarly to
MT8173, this SoC has the gamma LUT registers in DISP_AAL.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230412112739.160376-5-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add a compatible string for the MediaTek Helio X10 MT6795 SoC, using
the same parameters as MT8183.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230412112739.160376-4-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Core:
- Add Marijn Suijten as drm/msm reviewer
- Adreno A660 bindings
- SM8350 MDSS bindings fix
DP:
- Removed obsolete USB-PD remains
- Documented DP compatible string for sm8550 platform
DPU:
- Added support for DPU on sm6350 and sm6375 platforms
- Implemented tearcheck support to support vsync on SM150 and newer platforms
- Enabled missing features (DSPP, DSC, split display) on sc8180x, sc8280xp, sm8450
- Enabled writeback on sc7280
- Enabled DSC on msm8998
- Native HDMI output support
- Dropped unused features: regdma, GC, IGC
- Fixed the DSC flush operations
- Simplified QoS handling, removing obsolete and unused features and merging
SSPP and WB code paths
- Reworked dpu_encoder initialisation path
DSI:
- Added support for DSI and 28nm DSI PHY on MSM8226 platform
- Added support for DSI on sm6350 and sm6375 platforms
- Dropped powerup quirks in favour of using pre_enable_prev_first for
downstream bridges
- Fixed 14nm DSI PHY programming
MDP5:
- Added support for display controller on MSM8226 platform
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmR80iseHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGhxkH/2+2NEZjO5SCj9z6
FGrJunmXMOqoryoC3oL953Zhp3oeB/gB7GDdFQLg8tv0QprD6W0L9uorIgFi3lWU
doGWKSjFVEdu6RoUV09bTwm1DislZKJF3NCwTyeb44c3HnTzUvd/zFrY29YNRi9C
j5KXQIq91dke3qQi/3uCLFRKvmr2ss/lXapScwXFhQjaM2VmAMc51xIxkuRz3H01
EmcbJx3Rj9zPxx3Nc7ONMvtHE5+xuVsMdq3dLFCS9Xc/f+qbCCQdRIy9AjaRuR4c
F5nRjwDjq0iv2diF0gK4WtD8fvxVuLaqS0RAi0jsOKVfLphLwkqkPQbbMd5K8qwJ
xTNAiW0=
=FwWR
-----END PGP SIGNATURE-----
Merge tag 'v6.4-rc5' into media_stage
Linux 6.4-rc5
* tag 'v6.4-rc5': (919 commits)
Linux 6.4-rc5
leds: qcom-lpg: Fix PWM period limits
selftests/ftrace: Choose target function for filter test from samples
KVM: selftests: Add test for race in kvm_recalculate_apic_map()
KVM: x86: Bail from kvm_recalculate_phys_map() if x2APIC ID is out-of-bounds
KVM: x86: Account fastpath-only VM-Exits in vCPU stats
KVM: SVM: vNMI pending bit is V_NMI_PENDING_MASK not V_NMI_BLOCKING_MASK
KVM: x86/mmu: Grab memslot for correct address space in NX recovery worker
tpm, tpm_tis: correct tpm_tis_flags enumeration values
Revert "ext4: remove ac->ac_found > sbi->s_mb_min_to_scan dead check in ext4_mb_check_limits"
media: uvcvideo: Don't expose unsupported formats to userspace
media: v4l2-subdev: Fix missing kerneldoc for client_caps
media: staging: media: imx: initialize hs_settle to avoid warning
media: v4l2-mc: Drop subdev check in v4l2_create_fwnode_links_to_pad()
riscv: Implement missing huge_ptep_get
riscv: Fix huge_ptep_set_wrprotect when PTE is a NAPOT
module/decompress: Fix error checking on zstd decompression
fork, vhost: Use CLONE_THREAD to fix freezer/ps regression
dt-bindings: serial: 8250_omap: add rs485-rts-active-high
selinux: don't use make's grouped targets feature yet
...
SC7180, SM6350 and SM6375 use a rather similar hw setup for DPU, with
the main exception being that the last one requires an additional
throttle clock.
It is not well understood yet, but failing to toggle it on makes the
display hardware stall and not output any frames.
Document SM6350 and SM6375 DPU.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/541283/
Link: https://lore.kernel.org/r/20230411-topic-straitlagoon_mdss-v6-3-dee6a882571b@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The MSM8226 SoC uses a slightly different 28nm dsi phy. Add a new
compatible for it.
And while we're at it, in the dsi-phy-28nm.yaml move the 8960 compatible
to its correct place so its sorted alphabetically.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Patchwork: https://patchwork.freedesktop.org/patch/540621/
Link: https://lore.kernel.org/r/20230308-msm8226-mdp-v3-1-b6284145d67a@z3ntu.xyz
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The STARRY ili9882t is a 10.51" WUXGA TFT LCD panel,
which fits in nicely with the existing panel-boe-tv101wum-nl6
driver. Hence, we add a new compatible with panel specific config.
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230525093151.2338370-4-yangcong5@huaqin.corp-partner.google.com
The STARRY himax83102-j02 is a 10.51" WUXGA TFT LCD panel,
which fits in nicely with the existing panel-boe-tv101wum-nl6
driver. Hence, we add a new compatible with panel specific config.
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230525093151.2338370-2-yangcong5@huaqin.corp-partner.google.com
The Amlogic G12A, G12B & SM1 SoCs embeds a Synopsys DW-MIPI-DSI
transceiver (ver 1.21a) with a custom glue managing the IP resets,
clock and data inputs similar to the DW-HDMI Glue on the same
Amlogic SoC families.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512-amlogic-v6-4-upstream-dsi-ccf-vim3-v5-6-56eb7a4d5b8e@linaro.org
This chip has one reset GPIO input, document it. The reset GPIO
is optional as it is sometimes not connected on some hardware.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230530192805.648646-1-marex@denx.de
Use port-base reference for port@1.
This fixes the following schema warning:
imx8mp-dhcom-pdk3.dtb: dsi@32e60000: ports:port@1:endpoint: Unevaluated properties are not allowed ('data-lanes' was unexpected)
From schema: Documentation/devicetree/bindings/display/bridge/samsung,mipi-dsim.yaml
Fixes: 1f0d40d88f ("dt-bindings: bridge: Convert Samsung MIPI DSIM bridge to yaml")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
[narmstrong: removed line break between tags]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230531224407.1611952-1-festevam@gmail.com
Follow the dp-connector example and add hdmi-pwr supply to drive the 5V
pin of the HDMI connector (together with some simple glue logic possibly
attached to the connector).
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230531000259.3758235-2-dmitry.baryshkov@linaro.org
In the event a device is connected to the samsung-dsim
controller that doesn't support the burst-clock, the
driver is able to get the requested pixel clock from the
attached device or bridge. In these instances, the
samsung,burst-clock-frequency isn't needed, so remove
it from the required list.
The pll-clock frequency can be set by the device tree entry
for samsung,pll-clock-frequency, but in some cases, the
pll-clock may have the same clock rate as sclk_mipi clock.
If they are equal, this flag is not needed since the driver
will use the sclk_mipi rate as a fallback.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230528132727.3933-1-aford173@gmail.com
"#address-cells" and "#size-cells" are two properties that are not
mandatory. For instance, the DSI could refer to a bridge outside the scope
of the node rather than include a 'panel@0' subnode. By doing so, address
and size fields become then unnecessary, creating a warning at build time.
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
There is one LCDIF embedded in i.MX93 SoC to connect with
MIPI DSI controller through LCDIF cross line pattern(controlled
by mediamix blk-ctrl) or connect with LVDS display bridge(LDB)
directly or connect with a parallel display through parallel
display format(also controlled by mediamix blk-ctrl). i.MX93
LCDIF IP is essentially the same to i.MX8MP LCDIF IP. Add device
tree binding for i.MX93 LCDIF.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230510092450.4024730-2-victor.liu@nxp.com
In the event a device is connected to the samsung-dsim
controller that doesn't support the burst-clock, the
driver is able to get the requested pixel clock from the
attached device or bridge. In these instances, the
samsung,burst-clock-frequency isn't needed, so remove
it from the required list.
The pll-clock frequency can be set by the device tree entry
for samsung,pll-clock-frequency, but in some cases, the
pll-clock may have the same clock rate as sclk_mipi clock.
If they are equal, this flag is not needed since the driver
will use the sclk_mipi rate as a fallback.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230526030559.326566-8-aford173@gmail.com
The Tegra20 VI peripheral can receive parallel input from the VIP parallel
input module. Add it to the allowed properties and augment the existing
nvidia,tegra20-vi example to show a 'vip' property.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
VIP is the parallel video capture component within the video input
subsystem of Tegra20 (and other Tegra chips, apparently).
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The Samsung DSIM IP block allows the inversion of the clock and
data lanes.
Add an optional property called 'lane-polarities' that describes the
polarities of the MIPI DSI clock and data lanes.
This property is useful for properly describing the hardware when the
board designer decided to switch the polarities of the MIPI DSI
clock and/or data lanes.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230514114625.98372-1-festevam@gmail.com
Add bindings for the S6D7AA0 LCD panel controller, including the
S6D7AA0-LSL080AL02 panel used in the Samsung Galaxy Tab 3 8.0 family
of tablets, and the S6D7AA0-LSL080AL03 and S6D7AA0-LTL101AT01 panels
used in the Samsung Galaxy Tab A 8.0 and 9.7 2015.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230519170354.29610-2-aweber.kernel@gmail.com
The DSI compatible changed between patchset revisions, but that wasn't
reflected in the bindings. Fix it.
Fixes: 430e11f42b ("dt-bindings: display: msm: Add qcom, sm8350-mdss binding")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: David Heidelberg <david@ixit.cz>
Patchwork: https://patchwork.freedesktop.org/patch/528037/
Link: https://lore.kernel.org/r/20230321213557.1737905-1-konrad.dybcio@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add Adreno A660 to the A635 clause to define all version-specific
properties. There is no need to add it to the top-level clause, since
top-level compatible uses pattern to define compatible strings.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/521835/
Link: https://lore.kernel.org/r/20230209133839.762631-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
msm-fixes for v6.4-rc3
Display Fixes:
+ Catalog fixes:
- fix the programmable fetch lines and qos settings of msm8998
to match what is present downstream
- fix the LM pairs for msm8998 to match what is present downstream.
The current settings are not right as LMs with incompatible
connected blocks are paired
- remove unused INTF0 interrupt mask from SM6115/QCM2290 as there
is no INTF0 present on those chipsets. There is only one DSI on
index 1
- remove TE2 block from relevant chipsets because this is mainly
used for ping-pong split feature which is not supported upstream
and also for the chipsets where we are removing them in this
change, that block is not present as the tear check has been moved
to the intf block
- relocate non-MDP_TOP INTF_INTR offsets from dpu_hwio.h to
dpu_hw_interrupts.c to match where they belong
- fix the indentation for REV_7xxx interrupt masks
- fix the offset and version for dither blocks of SM8[34]50/SC8280XP
chipsets as it was incorrect
- make the ping-pong blk length 0 for appropriate chipsets as those
chipsets only have a dither ping-pong dither block but no other
functionality in the base ping-pong
- remove some duplicate register defines from INTF
+ Fix the log mask for the writeback block so that it can be enabled
correctly via debugfs
+ unregister the hdmi codec for dp during unbind otherwise it leaks
audio codec devices
+ Yaml change to fix warnings related to 'qcom,master-dsi' and
'qcom,sync-dual-dsi'
GPU Fixes:
+ fix submit error path leak
+ arm-smmu-qcom fix for regression that broke per-process page tables
+ fix no-iommu crash
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvHEcJfp=k6qatmb_SvAeyvy3CBpaPfwLqtNthuEzA_7w@mail.gmail.com
The TC358867/TC9595 devices are compatible with the predecessor TC358767.
Document compatible strings for the new devices, so they can be discerned
in board DTs. Update the title to match description in the process.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230515162033.66986-1-marex@denx.de
The Anbernic RG353V-V2 panel is a 3.5 inch 640x480 MIPI-DSI LCD panel.
It's based on the ST7703 LCD controller just like rocktech,jh057n00900.
It's used in a 2nd revision of the Anbernic RG353V handheld gaming
device. Like the first revision of the RG353V the control chip is known
but the panel itself is unknown, so name it for the device.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230426143213.4178586-2-macroalpha82@gmail.com
The trailing "/" in "lvds.yaml/#" is not a valid JSON pointer. The existing
jsonschema package allows it, but coming changes make allowed "$ref" URIs
stricter.
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20230418150658.1535120-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Lists (items) with one item should be just const or enum because it is
shorter and simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230414104230.23165-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Lists (items) with one item should be just enum because it is shorter,
simpler and does not confuse, if one wants to add new entry with a
fallback. Convert all of them to enums. OTOH, leave unused "oneOf"
entries in anticipation of further growth of the entire binding.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20230414083311.12197-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
video-interface.txt does not exist anymore, as it has been converted
to video-interfaces.yaml.
Instead of referencing video-interfaces.yaml multiple times,
pass it as a $ref to the schema.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20230412175800.2537812-1-festevam@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
Some Lenovo J606F tablets come with a 2K (2000x1200) 60Hz 11" 5:3
video mode display. Document it and allow rotation while at it (Lenovo
mounted it upside down!).
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230412-topic-lenovopanel-v3-1-bcf9ba4de46f@linaro.org
Backmerging drm-next to sync with msm tree. Resolves a conflict
between aperture-helper changes and msm's use of those interfaces.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
i.MX6SX has a single LVDS port and share a similar LDB_CTRL register
layout with i.MX8MP and i.MX93.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230404020129.509356-1-festevam@gmail.com
1. Add support for 10-bit overlays
2. Add MediaTek SoC DRM (vdosys1) support for mt8195
3. Change mmsys compatible for mt8195 mediatek-drm
4. Only trigger DRM HPD events if bridge is attached
5. Change the aux retries times when receiving AUX_DEFER
-----BEGIN PGP SIGNATURE-----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=T2t7
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-6.4' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 6.4
1. Add support for 10-bit overlays
2. Add MediaTek SoC DRM (vdosys1) support for mt8195
3. Change mmsys compatible for mt8195 mediatek-drm
4. Only trigger DRM HPD events if bridge is attached
5. Change the aux retries times when receiving AUX_DEFER
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230410233005.2572-1-chunkuang.hu@kernel.org
main pull request for v6.4
Core Display:
============
* Bugfixes for error handling during probe
* rework UBWC decoder programming
* prepare_commit cleanup
* bindings for SM8550 (MDSS, DPU), SM8450 (DP)
* timeout calculation fixup
* atomic: use drm_crtc_next_vblank_start() instead of our own
custom thing to calculate the start of next vblank
DP:
==
* interrupts cleanup
DPU:
===
* DSPP sub-block flush on sc7280
* support AR30 in addition to XR30 format
* Allow using REC_0 and REC_1 to handle wide (4k) RGB planes
* Split the HW catalog into individual per-SoC files
DSI:
===
* rework DSI instance ID detection on obscure platforms
GPU:
===
* uapi C++ compatibility fix
* a6xx: More robust gdsc reset
* a3xx and a4xx devfreq support
* update generated headers
* various cleanups and fixes
* GPU and GEM updates to avoid allocations which could trigger
reclaim (shrinker) in fence signaling path
* dma-fence deadline hint support and wait-boost
* a640 speedbin support
* a650 speedbin support
Conflicts in drivers/gpu/drm/msm/adreno/adreno_gpu.c:
Conflict between the 7fa5047a43 ("drm: Use of_property_present() for
testing DT property presence") and 9f251f9340 ("drm/msm/adreno: Use
OPP for every GPU generation"). The latter removed the of_ function
call outright, so I went with what's in the PR unchanged.
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvwuj5tabyW910+N-B=5kFNAC7QNYoQ=0xi3roBjQvFFQ@mail.gmail.com
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Core:
- Bugfixes for error handling during probe
- rework UBWC decoder programming
- prepare_commit cleanup
- bindings for SM8550 (MDSS, DPU), SM8450 (DP)
- uapi C++ compatibility fix
- timeout calculation fixup
- msm_fbdev conversion to drm_client
DP:
- interrupts cleanup
DPU:
- DSPP sub-block flush on sc7280
- support AR30 in addition to XR30 format
- Allow using REC_0 and REC_1 to handle wide (4k) RGB planes
DSI:
- rework DSI instance ID detection on obscure platforms
and misc small fixes as usual.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Merge DPU changes, resolving conflicts between branches. Full changelog
will be present in the final merge commit.
DPU:
- DSPP sub-block flush on sc7280
- support AR30 in addition to XR30 format
- Allow using REC_0 and REC_1 to handle wide (4k) RGB planes
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The point of the previous cleanup was to disallow "qcom,mdss-dsi-ctrl"
alone. This however didn't quite work out and the property became
undocumented instead of deprecated. Fix that.
Additionally, the "qcom," prefix was missed previously. Fix it.
Fixes: 0c0f65c6dd ("dt-bindings: msm: dsi-controller-main: Add compatible strings for every current SoC")
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/527651/
Link: https://lore.kernel.org/r/20230307-topic-dsi_qcm-v6-1-70e13b1214fa@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Samsung MIPI DSIM bridge can be found on Exynos and NXP's
i.MX8M Mini/Nano/Plus SoCs.
Convert exynos_dsim.txt to yaml.
Used the example node from exynos5433.dtsi instead of the one used in
the legacy exynos_dsim.txt.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230404023057.510329-1-festevam@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
Just as unevaluatedProperties or additionalProperties are required at
the top level of schemas, they should (and will) also be required for
child node schemas. That ensures only documented properties are
present.
Add unevaluatedProperties or additionalProperties as appropriate, and
then add any missing properties flagged by the addition.
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Lee Jones <lee@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230124230228.372305-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
The VS signal change is synchronized to HS signal change, start the
info graphics with that event, instead of having that event occur in
the middle of it.
Scope trace of DPI bus with HS/VS active HIGH looks as follows:
________________...__
VS...___/__ __ \______...
HS...___/ \_______/ \__...__/ \___...
^ ^
| |
| Used to start here -'
|
'--- Start info graphics here
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230221200407.16531-1-marex@denx.de
Panels are supposed to have one port (defined in panel-common.yaml
binding) and can have also rotation:
rk3326-odroid-go3.dtb: panel@0: 'port', 'rotation' do not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20230326204224.80181-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Panels are supposed to have one port (defined in panel-common.yaml
binding) and can have also rotation:
rk3326-odroid-go2.dtb: panel@0: 'port', 'rotation' do not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20230326204224.80181-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Panels are supposed to have one port (defined in panel-common.yaml
binding):
rk3399-rockpro64.dtb: panel@0: 'port' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230326204224.80181-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Panels are supposed to have one port (defined in panel-common.yaml
binding):
px30-evb.dtb: panel@0: 'port' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230326204224.80181-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
The device comes with DCX pin which is already used in
canaan/sipeed_maixduino.dts (although not in Linux driver).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230326164700.104570-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Marco's NXP email is no longer valid.
Marco told me offline that he has no interest to be listed as the
maintainer contact for this binding, so add my contact.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230329201150.741106-1-festevam@gmail.com
Allow 'rotation' property (coming from panel-common.yaml) already used
in DTS:
sc7180-trogdor-quackingstick-r0.dtb: panel@0: 'rotation' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230326155425.91181-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Panels are supposed to have one reg. This fixes dtbs_check warnings
like:
sc7180-idp.dtb: panel@0: 'reg' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230326155425.91181-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Panels are supposed to have one port (coming from panel-common.yaml
binding):
msm8916-samsung-a3u-eur.dtb: panel@0: 'port' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230326155425.91181-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Few panels like Samsung s6e3fc2x01 and sofef00 use vddio-supply instead
of power-supply (in DTS and Linux driver), so allow it to fix:
sdm845-oneplus-enchilada.dtb: panel@0: 'power-supply' is a required property
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230326155425.91181-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
The nt36672a bindings were added with a mistake on VDDIO supply calling
it in one place vddio and in other vddi0. Typical name is rather vddio
which is also now used by DTS (sdm845-xiaomi-beryllium-common.dtsi) and
Linux driver.
Fixes: c2abcf30ef ("dt-bindings: display: novatek,nt36672a: Fix unevaluated properties warning")
Fixes: 9528a02430 ("dt-bindings: display: panel: Add bindings for Novatek nt36672a")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230326155425.91181-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
There is nothing special in Innolux p120zdg-bf1 panel, so just like
other Innolux panels it can be made part of panel-simple.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230326155425.91181-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Samsung MIPI DSIM bridge can also be found in i.MX8M Plus SoC.
Add dt-bingings for it.
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Samsung MIPI DSIM bridge can also be found in i.MX8M Mini/Nano SoC.
Add dt-bingings for it.
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Cleanup bindings dropping unneeded quotes. Once all these are fixed,
checking for this can be enabled in yamllint.
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Miguel Ojeda <ojeda@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #display/msm
Link: https://lore.kernel.org/r/20230320233823.2919475-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Add vdosys1 ETHDR definition.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230321121859.2355-2-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The STARRY 2081101QFH032011-53G is a 10.1" WUXGA TFT LCD panel,
which fits in nicely with the existing panel-boe-tv101wum-nl6
driver. Hence, we add a new compatible with panel specific config.
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230314085034.6380-1-zhouruihai@huaqin.corp-partner.google.com
drm-misc-next for v6.4-rc1:
Note: Only changes since pull request from 2023-02-23 are included here.
UAPI Changes:
- Convert rockchip bindings to YAML.
- Constify kobj_type structure in dma-buf.
- FBDEV cmdline parser fixes, and other small fbdev fixes for mode
parsing.
Cross-subsystem Changes:
- Add Neil Armstrong as linaro maintainer.
- Actually signal the private stub dma-fence.
Core Changes:
- Add function for adding syncobj dep to sched_job and use it in panfrost, v3d.
- Improve DisplayID 2.0 topology parsing and EDID parsing in general.
- Add a gem eviction function and callback for generic GEM shrinker
purposes.
- Prepare to convert shmem helper to use the GEM reservation lock instead of own
locking. (Actual commit itself got reverted for now)
- Move the suballocator from radeon and amdgpu drivers to core in preparation
for Xe.
- Assorted small fixes and documentation.
- Fixes to HPD polling.
- Assorted small fixes in simpledrm, bridge, accel, shmem-helper,
and the selftest of format-helper.
- Remove dummy resource when ttm bo is created, and during pipelined
gutting. Fix all drivers to accept a NULL ttm_bo->resource.
- Handle pinned BO moving prevention in ttm core.
- Set drm panel-bridge orientation before connector is registered.
- Remove dumb_destroy callback.
- Add documentation to GEM_CLOSE, PRIME_HANDLE_TO_FD, PRIME_FD_TO_HANDLE, GETFB2 ioctl's.
- Add atomic enable_plane callback, use it in ast, mgag200, tidss.
Driver Changes:
- Use drm_gem_objects_lookup in vc4.
- Assorted small fixes to virtio, ast, bridge/tc358762, meson, nouveau.
- Allow virtio KMS to be disabled and compiled out.
- Add Radxa 8/10HD, Samsung AMS495QA01 panels.
- Fix ivpu compiler errors.
- Assorted fixes to drm/panel, malidp, rockchip, ivpu, amdgpu, vgem,
nouveau, vc4.
- Assorted cleanups, simplifications and fixes to vmwgfx.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ac1f5186-54bb-02f4-ac56-907f5b76f3de@linux.intel.com
The item which have the mediatek,mt8192-disp-ccorr as const compatible
already exist above. Merge all compatibles which have the same fallback
under the same item.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230306-ccorr-binding-fix-v5-0-6c56aaecc3b1@baylibre.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Enable yamllint to check the preferred commenting style of requiring a
space after a comment character '#'. Fix the cases in the tree which
have a warning with this enabled. Most cases just need a space after the
'#'. A couple of cases with comments which were not intended to be
comments are revealed. Those were in ti,sa2ul.yaml, ti,cal.yaml, and
brcm,bcmgenet.yaml.
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # drm/msm
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230303214223.49451-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
SPI and I2C bus node names are expected to be "spi" or "i2c",
respectively, with nothing else, a unit-address, or a '-N' index. A
pattern of 'spi0' or 'i2c0' or similar has crept in. Fix all these
cases. Mostly scripted with the following commands:
git grep -l '\si2c[0-9] {' Documentation/devicetree/ | xargs sed -i -e 's/i2c[0-9] {/i2c {/'
git grep -l '\sspi[0-9] {' Documentation/devicetree/ | xargs sed -i -e 's/spi[0-9] {/spi {/'
With this, a few errors in examples were exposed and fixed.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for the microchip,mcp251xfd.yaml
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for power-supply
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230228215433.3944508-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the Parade PS8622/PS8625 DisplayPort to LVDS Converter bindings
to DT schema. Changes during conversion: add missing vdd12-supply, used
by Linux driver.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230221170955.62448-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Add bindings for the display panel used on some Sony Xperia XZ2 and XZ2
Compact smartphones.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230119163201.580858-1-konrad.dybcio@linaro.org
DT core:
- Add node lifecycle unit tests
- Add of_property_present() helper aligned with fwnode API
- Print more information on reserved regions on boot
- Update dtc to upstream v1.6.1-66-gabbd523bae6e
- Use strscpy() to instead of strncpy() in DT core
- Add option for schema validation on %.dtb targets
Bindings:
- Add/fix support for listing multiple patterns in DT_SCHEMA_FILES
- Rework external memory controller/bus bindings to properly support
controller specific child node properties
- Convert loongson,ls1x-intc, fcs,fusb302, sil,sii8620, Rockchip RK3399
PCIe, Synquacer I2C, and Synquacer EXIU bindings to DT schema format
- Add RiscV SBI PMU event mapping binding
- Add missing contraints on Arm SCMI child node allowed properties
- Add a bunch of missing Socionext UniPhier glue block bindings and
example fixes
- Various fixes for duplicate or conflicting type definitions on DT
properties
-----BEGIN PGP SIGNATURE-----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=ywsL
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DT core:
- Add node lifecycle unit tests
- Add of_property_present() helper aligned with fwnode API
- Print more information on reserved regions on boot
- Update dtc to upstream v1.6.1-66-gabbd523bae6e
- Use strscpy() to instead of strncpy() in DT core
- Add option for schema validation on %.dtb targets
Bindings:
- Add/fix support for listing multiple patterns in DT_SCHEMA_FILES
- Rework external memory controller/bus bindings to properly support
controller specific child node properties
- Convert loongson,ls1x-intc, fcs,fusb302, sil,sii8620, Rockchip
RK3399 PCIe, Synquacer I2C, and Synquacer EXIU bindings to DT
schema format
- Add RiscV SBI PMU event mapping binding
- Add missing contraints on Arm SCMI child node allowed properties
- Add a bunch of missing Socionext UniPhier glue block bindings and
example fixes
- Various fixes for duplicate or conflicting type definitions on DT
properties"
* tag 'devicetree-for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (66 commits)
dt-bindings: regulator: Add mps,mpq7932 power-management IC
of: dynamic: Fix spelling mistake "kojbect" -> "kobject"
dt-bindings: drop Sagar Kadam from SiFive binding maintainership
dt-bindings: sram: qcom,imem: document sm8450
dt-bindings: interrupt-controller: convert loongson,ls1x-intc.txt to json-schema
dt-bindings: arm: Add Cortex-A715 and X3
of: dynamic: add lifecycle docbook info to node creation functions
of: add consistency check to of_node_release()
of: do not use "%pOF" printk format on node with refcount of zero
of: unittest: add node lifecycle tests
of: update kconfig unittest help
of: add processing of EXPECT_NOT to of_unittest_expect
of: prepare to add processing of EXPECT_NOT to of_unittest_expect
of: Use preferred of_property_read_* functions
of: Use of_property_present() helper
of: Add of_property_present() helper
of: reserved_mem: Use proper binary prefix
dt-bindings: Fix multi pattern support in DT_SCHEMA_FILES
of: reserved-mem: print out reserved-mem details during boot
dt-bindings: serial: restrict possible child node names
...
Removals:
- remove legacy dri1 drivers -
- i810, mga, r128, savage, sis, tdfx, via
New driver:
- intel VPU accelerator driver
- habanalabs comes via drm tree now
drm/core:
- use drm_dbg_ helpers in several places
- Document defaults for CRTC backgrounds
- Document use of drm_minor
edid:
- improve mode parsing and refactoring
connector:
- support analog TV mode property
media:
- add some common formats
udmabuf:
- add vmap/vunmap methods
fourcc:
- add XRGB1555 and RGB565 formats
- document open source user waiver
firmware:
- fix color-format selection for system framebuffer
format-helper:
- Add conversion from XRGB8888 to various sysfb formats
- Make XRGB8888 the only driver-emulated legacy format
- Add conversion from XRGB8888 to XBGR8888 and ABGR8888
fb-helper:
- fix preferred depth and bpp values across drivers
- Avoid blank consoles from selecting an incorrect color format
probe-helper:
- Enable/disable HPD on connectors
scheduler:
- Fix lockup in drm_sched_entity_kill()
- Deprecate drm_sched_resubmit_jobs()
bridge:
- remove unused functions
- implement i2c probe_new in various drivers
- ite-it6505: Locking fixes, Cache EDID data
- ite-it66121: Support IT6610 chip
- lontium-tl9611: Fix HDMI on DragonBoard 845c
- parade-ps8640: Use atomic bridge functions
- Support i.MX93 LDB plus DT bindings
debugfs:
- add per device helpers and convert drivers
displayport:
- mst fixes
- add DP adaptive sync DPCD definitions
fbdev:
- always pick 32bpp as default
- remove some unused code
simpledrm:
- support system memory framebuffers
panel:
- add orientation quirks for Lenovo Yoga Tab 3 X90F and DynaBook K50
- Use ktime_get_boottime() to measure power-down delay
- Fix auto-suspend delay
- Visionox VTDR6130 AMOLED DSI
- Support Himax HX8394
- Convert many drivers to common generic DSI write-sequence helper
- AUO A030JTN01
ttm:
- drop bo wait wrapper
- fix MIPS build
habanalabs:
- moved driver to accel subsystem
- gaudi2 decoder error improvement
- more trace events
- Gaudi2 abrupt reset by firmware support
- add uAPI to flush memory transactions
- add uAPI to pass through userspace reqs to fw
- remove dma-buf export by handle
amdgpu:
- add new INFO queries for peak and min sclk/mclk for profile modes
- Add PCIe info to the INFO IOCTL
- secure display support for multiple displays
- DML optimizations
- DCN 3.2 updates
- PSR updates
- DP 2.1 updates
- SR-IOV RAS updates
- VCN RAS support
- SMU 13.x updates
- Switch 1 element arrays to flexible arrays
- Add RAS support for DF 4.3
- Stack size improvements
- S0ix rework
- Allow 0 as a vram limit on APUs
- Handle profiling modes for SMU13.x
- Fix possible segfault in failure case
- Rework FW requests to happen in early_init for all IPs so
that we don't lose the sbios console if FW is missing
- Fix power reporting on certain firmwares for CZN/RN
- Allow S0ix without BIOS support
- Enable freesync over PCon
- Re-enable the AGP aperture on GMC 11.x
amdkfd:
- Error handling fixes
- PASID fixes
- Fix for cleared VRAM BOs
- Fix cleanup if GPUVM creation fails
- Memory accounting fix
- Use resource_size rather than open codeing it
- GC11 mGPU fix
radeon:
- Switch 1 element arrays to flexible arrays
- Fix memory leak on shutdown
- move to new logging
i915:
- Meteorlake display/OA/GSC fw/workarounds enabling
- DP MST DSC support
- Gamma/degamma readout support for the state checker
- Enable SDP split support for DP 2.0
- Add probe blocking support to i915.force_probe parameter
- Enable Xe HP 4tile support
- Avoid display direct calls to uncore
- Fix HuC delayed load memory leaks
- Add DG2 workarounds Wa_18018764978 and Wa_18019271663
- Improve suspend / resume times with VT-d scanout workaround active
- Fix DG2 visual corruption on small BAR systems by not forgetting to copy CCS aux state
- Fix TLB invalidation for Gen12.50 video and compute engines
- Enable HF-EEODB by switching HDMI, DP and LVDS to use struct drm_edid
- Start using unversioned DMC firmware paths for new platforms
- ELD refactor: Stop using hardware buffer, precompute ELD
- lots of display code refactoring
nouveau:
- drop legacy ioctl support
- replace 0-sized array
msm:
- dpu/dsi/mdss: Support for SM8350, SM8450 SM8550 and SC8280XP platform
- Added bindings for SM8150
- dpu: Partial support for DSC on SM8150 and SM8250
- dpu: Fixed color transformation matrix being lost on suspend/resume
- dp: Support SDM845 and SC8280XP platforms
- dp: Support for limiting DP link rate via DT property
- dsi: Validate display modes according to the DSI OPP table
- dsi: DSI PHY support for the SM6375 platform
- Add MSM_SUBMIT_BO_NO_IMPLICI
- a2xx: Support to load legacy firmware
- a6xx: GPU devcore dump updates for a650/a660
- GPU devfreq tuning and fixes
- Turn 8960 HDMI PHY into clock provider,
- Make 8960 HDMI PHY use PXO clock from DT
etnaviv:
- experimental versilicon NPU support
- report GPU load via fdinfo format
- MMU fault message improvements
tegra:
- rework syncpoint interrupt
mediatek:
- DSI timing fix
- fix config deps
ast:
- various fixes
exynos:
- restore bridge chain order fixes
gud:
- convert to shadow plane buffers
- perform flushing synchronously during atomic update
- Use new debugfs helpers
arm/hdlcd:
- Use new debugfs helper
ili9486:
- Support 16-bit pixel data
imx:
- Split off IPUv3 driver
mipi-dbi:
- convert to DRM shadow-plane helpers
- rsp driver changes
- Support separate I/O-voltage supply
mxsfb:
- Depend on ARCH_MXS or ARCH_MXC
sun4i:
- convert to new TV mode property
vc4:
- convert to new TV mode property
- kunit tests
- Support RGB565 and RGB666 formats
- convert dsi driver to bridge
- Various HVS an CRTC fixes
v3d:
- Do not opencode drm_gem_object_lookup()
virtio:
- improve tracing
vkms:
- support small cursors in IGT tests
- Fix SEGFAULT from incorrect GEM-buffer mapping
rcar-du:
- fixes and improvements
-----BEGIN PGP SIGNATURE-----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=HQUi
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2023-02-23' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"There are a bunch of changes all over in the usual places.
Highlights:
- habanalabs moves from misc to accel
- first accel driver for Intel VPU (Versatile Processing Unit)
inference engine
- dropped all the ancient legacy DRI1 drivers. I think it's been at
least 10 years since anyone has heard about these.
- Intel DG2 updates and prelim Meteorlake enablement
- etnaviv adds support for Versilicon NPU device (a GPU like engine
with inference accelerators)
Detailed summary:
Removals:
- remove legacy dri1 drivers: i810, mga, r128, savage, sis, tdfx, via
New driver:
- intel VPU accelerator driver
- habanalabs comes via drm tree now
drm/core:
- use drm_dbg_ helpers in several places
- Document defaults for CRTC backgrounds
- Document use of drm_minor
edid:
- improve mode parsing and refactoring
connector:
- support analog TV mode property
media:
- add some common formats
udmabuf:
- add vmap/vunmap methods
fourcc:
- add XRGB1555 and RGB565 formats
- document open source user waiver
firmware:
- fix color-format selection for system framebuffer
format-helper:
- Add conversion from XRGB8888 to various sysfb formats
- Make XRGB8888 the only driver-emulated legacy format
- Add conversion from XRGB8888 to XBGR8888 and ABGR8888
fb-helper:
- fix preferred depth and bpp values across drivers
- Avoid blank consoles from selecting an incorrect color format
probe-helper:
- Enable/disable HPD on connectors
scheduler:
- Fix lockup in drm_sched_entity_kill()
- Deprecate drm_sched_resubmit_jobs()
bridge:
- remove unused functions
- implement i2c probe_new in various drivers
- ite-it6505: Locking fixes, Cache EDID data
- ite-it66121: Support IT6610 chip
- lontium-tl9611: Fix HDMI on DragonBoard 845c
- parade-ps8640: Use atomic bridge functions
- Support i.MX93 LDB plus DT bindings
debugfs:
- add per device helpers and convert drivers
displayport:
- mst fixes
- add DP adaptive sync DPCD definitions
fbdev:
- always pick 32bpp as default
- remove some unused code
simpledrm:
- support system memory framebuffers
panel:
- add orientation quirks for Lenovo Yoga Tab 3 X90F and DynaBook K50
- Use ktime_get_boottime() to measure power-down delay
- Fix auto-suspend delay
- Visionox VTDR6130 AMOLED DSI
- Support Himax HX8394
- Convert many drivers to common generic DSI write-sequence helper
- AUO A030JTN01
ttm:
- drop bo wait wrapper
- fix MIPS build
habanalabs:
- moved driver to accel subsystem
- gaudi2 decoder error improvement
- more trace events
- Gaudi2 abrupt reset by firmware support
- add uAPI to flush memory transactions
- add uAPI to pass through userspace reqs to fw
- remove dma-buf export by handle
amdgpu:
- add new INFO queries for peak and min sclk/mclk for profile modes
- Add PCIe info to the INFO IOCTL
- secure display support for multiple displays
- DML optimizations
- DCN 3.2 updates
- PSR updates
- DP 2.1 updates
- SR-IOV RAS updates
- VCN RAS support
- SMU 13.x updates
- Switch 1 element arrays to flexible arrays
- Add RAS support for DF 4.3
- Stack size improvements
- S0ix rework
- Allow 0 as a vram limit on APUs
- Handle profiling modes for SMU13.x
- Fix possible segfault in failure case
- Rework FW requests to happen in early_init for all IPs so that we
don't lose the sbios console if FW is missing
- Fix power reporting on certain firmwares for CZN/RN
- Allow S0ix without BIOS support
- Enable freesync over PCon
- Re-enable the AGP aperture on GMC 11.x
amdkfd:
- Error handling fixes
- PASID fixes
- Fix for cleared VRAM BOs
- Fix cleanup if GPUVM creation fails
- Memory accounting fix
- Use resource_size rather than open codeing it
- GC11 mGPU fix
radeon:
- Switch 1 element arrays to flexible arrays
- Fix memory leak on shutdown
- move to new logging
i915:
- Meteorlake display/OA/GSC fw/workarounds enabling
- DP MST DSC support
- Gamma/degamma readout support for the state checker
- Enable SDP split support for DP 2.0
- Add probe blocking support to i915.force_probe parameter
- Enable Xe HP 4tile support
- Avoid display direct calls to uncore
- Fix HuC delayed load memory leaks
- Add DG2 workarounds Wa_18018764978 and Wa_18019271663
- Improve suspend / resume times with VT-d scanout workaround active
- Fix DG2 visual corruption on small BAR systems by not forgetting to
copy CCS aux state
- Fix TLB invalidation for Gen12.50 video and compute engines
- Enable HF-EEODB by switching HDMI, DP and LVDS to use struct
drm_edid
- Start using unversioned DMC firmware paths for new platforms
- ELD refactor: Stop using hardware buffer, precompute ELD
- lots of display code refactoring
nouveau:
- drop legacy ioctl support
- replace 0-sized array
msm:
- dpu/dsi/mdss: Support for SM8350, SM8450 SM8550 and SC8280XP platform
- Added bindings for SM8150
- dpu: Partial support for DSC on SM8150 and SM8250
- dpu: Fixed color transformation matrix being lost on suspend/resume
- dp: Support SDM845 and SC8280XP platforms
- dp: Support for limiting DP link rate via DT property
- dsi: Validate display modes according to the DSI OPP table
- dsi: DSI PHY support for the SM6375 platform
- Add MSM_SUBMIT_BO_NO_IMPLICI
- a2xx: Support to load legacy firmware
- a6xx: GPU devcore dump updates for a650/a660
- GPU devfreq tuning and fixes
- Turn 8960 HDMI PHY into clock provider,
- Make 8960 HDMI PHY use PXO clock from DT
etnaviv:
- experimental versilicon NPU support
- report GPU load via fdinfo format
- MMU fault message improvements
tegra:
- rework syncpoint interrupt
mediatek:
- DSI timing fix
- fix config deps
ast:
- various fixes
exynos:
- restore bridge chain order fixes
gud:
- convert to shadow plane buffers
- perform flushing synchronously during atomic update
- Use new debugfs helpers
arm/hdlcd:
- Use new debugfs helper
ili9486:
- Support 16-bit pixel data
imx:
- Split off IPUv3 driver
mipi-dbi:
- convert to DRM shadow-plane helpers
- rsp driver changes
- Support separate I/O-voltage supply
mxsfb:
- Depend on ARCH_MXS or ARCH_MXC
sun4i:
- convert to new TV mode property
vc4:
- convert to new TV mode property
- kunit tests
- Support RGB565 and RGB666 formats
- convert dsi driver to bridge
- Various HVS an CRTC fixes
v3d:
- Do not opencode drm_gem_object_lookup()
virtio:
- improve tracing
vkms:
- support small cursors in IGT tests
- Fix SEGFAULT from incorrect GEM-buffer mapping
rcar-du:
- fixes and improvements"
* tag 'drm-next-2023-02-23' of git://anongit.freedesktop.org/drm/drm: (1455 commits)
msm/fbdev: fix unused variable warning with clang.
drm/fb-helper: Remove drm_fb_helper_unprepare() from drm_fb_helper_fini()
dma-buf: make kobj_type structure constant
drm/shmem-helper: Fix locking for drm_gem_shmem_get_pages_sgt()
drm/amd/display: disable SubVP + DRR to prevent underflow
drm/amd/display: Fail atomic_check early on normalize_zpos error
drm/amd/pm: avoid unaligned access warnings
drm/amd/display: avoid unaligned access warnings
drm/amd/display: Remove duplicate/repeating expressions
drm/amd/display: Remove duplicate/repeating expression
drm/amd/display: Make variables declaration inside ifdef guard
drm/amd/display: Fix excess arguments on kernel-doc
drm/amd/display: Add previously missing includes
drm/amd/amdgpu: Add function prototypes to headers
drm/amd/display: Add function prototypes to headers
drm/amd/display: Turn global functions into static
drm/amd/display: remove unused _calculate_degamma_curve function
drm/amd/display: remove unused func declaration from resource headers
drm/amd/display: unset initial value for tf since it's never used
drm/amd/display: camel case cleanup in color_gamma file
...
About a quarter of the changes are for 32-bit arm, mostly filling in
device support for existing machines and adding minor cleanups, mostly
for Qualcomm and Samsung based machines.
Two new 32-bit SoCs are added, both are quad-core Cortex-A7 chips from
Rockchips that have been around for a while but were lacking kernel
support so far: RV1126 is a Vision SoC with an NPU and is used in the
Edgeble Neural Compute Module 2(Neu2) board, while RK3128 is design for
TV boxes and so far only comes with a dts for its refernece design.
The other 32-bit boards that were added are two ASpeed AST2600 based BMC
boards, the Microchip sam9x60_curiosity development board (Armv5 based!),
the Enclustra PE1 FPGA-SoM baseboard, and a few more boards for i.MX53
and i.MX6ULL.
On the RISC-V side, there are fewer patches, but a total of ten new
single-board computers based on variations of the Allwinner D1/T113 chip,
plus one more board based on Microchip Polarfire.
As usual, arm64 has by far the most changes here, with over 700 non-merge
changesets, among them over 400 alone for Qualcomm. The newly added SoCs
this time are all recent high-end embedded SoCs for various markets,
each on comes with support for its reference board:
- Qualcomm SM8550 (Snapdragon 8 Gen 2) for mobile phones
- Qualcomm QDU1000/QRU1000 5G RAN platform
- Rockchips RK3588/RK3588s for tablets, chromebooks and SBCs
- TI J784S4 for industrial and automotive applications
In total, there are 46 new arm64 machines:
- Reference platforms for each of the five new SoCs
- Three Amlogic based development boards
- Six embedded machines based on NXP i.MX8MM and i.MX8MP
- The Mediatek mt7986a based Banana Pi R3 router
- Six tablets based on Qualcomm MSM8916 (Snapdragon 410),
SM6115 (Snapdragon 662) and SM8250 (Snapdragon 865)
- Two LTE dongles, also based on MSM8916
- Seven mobile phones, based on Qualcomm MSM8953 (Snapdragon 610),
SDM450 and SDM632
- Three chromebooks based on Qualcomm SC7280 (Snapdragon 7c)
- Nine development boards based on Rockchips RK3588, RK3568,
RK3566 and RK3328.
- Five development machines based on TI K3 (AM642/AM654/AM68/AM69)
The cleanup of dtc warnings continues across all platforms, adding
to the total number of changes.
-----BEGIN PGP SIGNATURE-----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=I8Ga
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC DT updates from Arnd Bergmann:
"About a quarter of the changes are for 32-bit arm, mostly filling in
device support for existing machines and adding minor cleanups, mostly
for Qualcomm and Samsung based machines.
Two new 32-bit SoCs are added, both are quad-core Cortex-A7 chips from
Rockchips that have been around for a while but were lacking kernel
support so far: RV1126 is a Vision SoC with an NPU and is used in the
Edgeble Neural Compute Module 2(Neu2) board, while RK3128 is design
for TV boxes and so far only comes with a dts for its refernece
design.
The other 32-bit boards that were added are two ASpeed AST2600 based
BMC boards, the Microchip sam9x60_curiosity development board (Armv5
based!), the Enclustra PE1 FPGA-SoM baseboard, and a few more boards
for i.MX53 and i.MX6ULL.
On the RISC-V side, there are fewer patches, but a total of ten new
single-board computers based on variations of the Allwinner D1/T113
chip, plus one more board based on Microchip Polarfire.
As usual, arm64 has by far the most changes here, with over 700
non-merge changesets, among them over 400 alone for Qualcomm. The
newly added SoCs this time are all recent high-end embedded SoCs for
various markets, each on comes with support for its reference board:
- Qualcomm SM8550 (Snapdragon 8 Gen 2) for mobile phones
- Qualcomm QDU1000/QRU1000 5G RAN platform
- Rockchips RK3588/RK3588s for tablets, chromebooks and SBCs
- TI J784S4 for industrial and automotive applications
In total, there are 46 new arm64 machines:
- Reference platforms for each of the five new SoCs
- Three Amlogic based development boards
- Six embedded machines based on NXP i.MX8MM and i.MX8MP
- The Mediatek mt7986a based Banana Pi R3 router
- Six tablets based on Qualcomm MSM8916 (Snapdragon 410), SM6115
(Snapdragon 662) and SM8250 (Snapdragon 865)
- Two LTE dongles, also based on MSM8916
- Seven mobile phones, based on Qualcomm MSM8953 (Snapdragon 610),
SDM450 and SDM632
- Three chromebooks based on Qualcomm SC7280 (Snapdragon 7c)
- Nine development boards based on Rockchips RK3588, RK3568, RK3566
and RK3328.
- Five development machines based on TI K3 (AM642/AM654/AM68/AM69)
The cleanup of dtc warnings continues across all platforms, adding to
the total number of changes"
* tag 'soc-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (1035 commits)
dt-bindings: riscv: correct starfive visionfive 2 compatibles
ARM: dts: socfpga: Add enclustra PE1 devicetree
dt-bindings: altera: Add enclustra mercury PE1
arm64: dts: qcom: msm8996: align RPM G-Link clock-controller node with bindings
arm64: dts: qcom: qcs404: align RPM G-Link node with bindings
arm64: dts: qcom: ipq6018: align RPM G-Link node with bindings
arm64: dts: qcom: sm8550: remove invalid interconnect property from cryptobam
arm64: dts: qcom: sc7280: Adjust zombie PWM frequency
arm64: dts: qcom: sc8280xp-pmics: Specify interrupt parent explicitly
arm64: dts: qcom: sm7225-fairphone-fp4: enable remaining i2c busses
arm64: dts: qcom: sm7225-fairphone-fp4: move status property down
arm64: dts: qcom: pmk8350: Use the correct PON compatible
arm64: dts: qcom: sc8280xp-x13s: Enable external display
arm64: dts: qcom: sc8280xp-crd: Introduce pmic_glink
arm64: dts: qcom: sc8280xp: Add USB-C-related DP blocks
arm64: dts: qcom: sm8350-hdk: enable GPU
arm64: dts: qcom: sm8350: add GPU, GMU, GPU CC and SMMU nodes
arm64: dts: qcom: sm8350: finish reordering nodes
arm64: dts: qcom: sm8350: move more nodes to correct place
arm64: dts: qcom: sm8350: reorder device nodes
...
Contains a number of fixes to vc4 and ivpu. The patches to the probe
helpers were cherry-picked from the regular development branch.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAmPkufIACgkQaA3BHVML
eiN5WQf+KUHujvKiUf1/gKzUzjfW7Zl9MiRdCiW0GWIvo8BDPk7PaUYwg2SxOp7h
giGtZh8kMR2kzNBvFv2lgkkysmNcamogLqwicr4KxYeI9/EEJ/A6bZ5T0G2DrQRR
FXD4OD3wf/gIa0Ilse6nP0ag/UOahUNykSsvQhx1pE3KClzLO8lcbqKR+WXWnuJQ
PygFyAoqpkXzVE1FxzLdy0cg+MeDPXpc8rdhjmMCxzXZoetNiCvDw0Bk4QHi81xI
pvkQ0CeYNsC+G1mYC/Xamssz0LVW8undGqvA9enI/tsXjpQhdyfKlss/LHxbkxrw
dvn9GFE3IC6A7vqbFh5w5K5H+RBREA==
=jUJo
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-fixes-2023-02-09' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
Short summary of fixes pull:
Contains a number of fixes to vc4 and ivpu. The patches to the probe
helpers were cherry-picked from the regular development branch.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/Y+S6HBmaRJNPYiBG@linux-uq9g
msm-next for v6.3
There is one devfreq patch, maintainer acked to land via msm-next to
avoid a build break on platforms that do not support PM_DEVFREQ. And
otherwise the usual assortment:
GPU:
- Add MSM_SUBMIT_BO_NO_IMPLICIT
- a2xx: Support to load legacy firmware
- a6xx: GPU devcore dump updates for a650/a660
- GPU devfreq tuning and fixes
DPU, DSI, MDSS:
- Support for SM8350, SM8450 SM8550 and SC8280XP platform
Core:
- Added bindings for SM8150 (driver support already present)
DPU:
- Partial support for DSC on SM8150 and SM8250
- Fixed color transformation matrix being lost on suspend/resume
- Include DSC blocks into register snapshot
- Misc HW catalog fixes
DP:
- Support for DP on SDM845 and SC8280XP platforms
- HPD fixes
- Support for limiting DP link rate via DT property, this enables
- Support for HBR3 rates.
DSI:
- Validate display modes according to the DSI OPP table
- DSI PHY support for the SM6375 platform
- Fixed byte intf clock selection for 14nm PHYs
- Fix the case of empty OPP tables (fixing db410c)
- DT schema rework and fixes
HDMI:
- Turn 8960 HDMI PHY into clock provider,
- Make 8960 HDMI PHY use PXO clock from DT
MDP5:
- Schema conversion to YAML
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGv6zQ-zsgS+NG+WuV=tk51q9vA2QdKqYhNgiXQddAdZjA@mail.gmail.com
1. Reduce the time of dsi from LP11 to sending cmd
2. Remove dependency on GEM DMA helper
3. Drop unbalanced obj unref
4. Fix the fallback for mediatek,mt8186-disp-ccorr
5. Fixup for error path.
-----BEGIN PGP SIGNATURE-----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=ZhnI
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 6.3
1. Reduce the time of dsi from LP11 to sending cmd
2. Remove dependency on GEM DMA helper
3. Drop unbalanced obj unref
4. Fix the fallback for mediatek,mt8186-disp-ccorr
5. Fixup for error path.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130125811.2567-1-chunkuang.hu@kernel.org
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmPW7E8eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGf7MIAI0JnHN9WvtEukSZ
E6j6+cEGWxsvD6q0g3GPolaKOCw7hlv0pWcFJFcUAt0jebspMdxV2oUGJ8RYW7Lg
nCcHvEVswGKLAQtQSWw52qotW6fUfMPsNYYB5l31sm1sKH4Cgss0W7l2HxO/1LvG
TSeNHX53vNAZ8pVnFYEWCSXC9bzrmU/VALF2EV00cdICmfvjlgkELGXoLKJJWzUp
s63fBHYGGURSgwIWOKStoO6HNo0j/F/wcSMx8leY8qDUtVKHj4v24EvSgxUSDBER
ch3LiSQ6qf4sw/z7pqruKFthKOrlNmcc0phjiES0xwwGiNhLv0z3rAhc4OM2cgYh
SDc/Y/c=
=zpaD
-----END PGP SIGNATURE-----
Merge v6.2-rc6 into drm-next
Due to holidays we started -next with more -fixes in-flight than
usual, and people have been asking where they are. Backmerge to get
things better in sync.
Conflicts:
- Tiny conflict in drm_fbdev_generic.c between variable rename and
missing error handling that got added.
- Conflict in drm_fb_helper.c between the added call to vgaswitcheroo
in drm_fb_helper_single_fb_probe and a refactor patch that extracted
lots of helpers and incidentally removed the dev local variable.
Readd it to make things compile.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The mt8186-disp-ccorr is not fully compatible with the mt8183-disp-ccorr
implementation. It causes a crash when system resumes if it binds to the
device.
We should use mt8192-disp-ccorr as fallback of mt8186-disp-ccorr.
Fixes: 8a26ea19d4 ("dt-bindings: display: mediatek: add MT8186 SoC binding")
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230118091829.755-10-allen-kh.cheng@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Both 1 and 2 are valid values for #address-cells and #size-cells on the
various busses specified in these bindings, so explicitly allow 2.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Radxa Display 8HD is a family of DSI panels from Radxa that
uses jd9365da-h3 IC.
Add compatible string for it.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230123183312.436573-3-jagan@edgeble.ai
Radxa Display 10HD is a family of DSI panels from Radxa that
uses jd9365da-h3 IC.
Add compatible string for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230123183312.436573-1-jagan@edgeble.ai
Stop mentioning #address-cells/#size-cells which are defined in
display/dsi-controller.yaml. Use unevaluatedProperties instead of
additionalProperties to allow skipping properties defined in other
schema files.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/518809/
Link: https://lore.kernel.org/r/20230118032432.1716616-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Currently we do not differentiate between the various users of the
qcom,mdss-dsi-ctrl. The driver is flexible enough to operate from one
compatible string but, the hardware does have some significant differences
in the number of clocks.
To facilitate documenting the clocks add the following compatible strings
- qcom,apq8064-dsi-ctrl
- qcom,msm8916-dsi-ctrl
- qcom,msm8953-dsi-ctrl
- qcom,msm8974-dsi-ctrl
- qcom,msm8996-dsi-ctrl
- qcom,msm8998-dsi-ctrl
- qcom,sc7180-dsi-ctrl
- qcom,sc7280-dsi-ctrl
- qcom,sdm660-dsi-ctrl
- qcom,sdm845-dsi-ctrl
- qcom,sm8150-dsi-ctrl
- qcom,sm8250-dsi-ctrl
- qcom,sm8350-dsi-ctrl
- qcom,sm8450-dsi-ctrl
- qcom,sm8550-dsi-ctrl
- qcom,qcm2290-dsi-ctrl
Deprecate qcom,dsi-ctrl-6g-qcm2290 in favour of the desired format while we
do so.
Several MDSS yaml files exist which document the dsi sub-node.
For each existing SoC MDSS yaml, provide the right dsi compat string.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/519078/
Link: https://lore.kernel.org/r/20230118171621.102694-2-bryan.odonoghue@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The type for operating-points-v2 property is coming from dtschema
(/schemas/opp/opp.yaml), so individual bindings can just use simple
"true".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230119131033.117324-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Same to i.MX8mp LDB, i.MX93 LDB is controlled by mediamix blk-ctrl
through 'ldb' register and 'lvds' register. Also, the 'ldb' clock
is required. i.MX93 LDB supports only one LVDS channel(channel 0,
a.k.a, LVDS Channel-A in the device tree binding documentation), while
i.MX8mp LDB supports at most two. Add i.MX93 LDB device tree binding
in the existing i.MX8mp LDB device tree binding documentation.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230123021449.969243-2-victor.liu@nxp.com
Merge display-related changes targeting Qualcomm DRM MSM driver.
Notable changes:
DPU, DSI, MDSS:
- Support for SM8350, SM8450 SM8550 and SC8280XP platform
Core:
- Added bindings for SM8150 (driver support already present)
DPU:
- Partial support for DSC on SM8150 and SM8250
- Fixed color transformation matrix being lost on suspend/resume
DP:
- Support for DP on SDM845 and SC8280XP platforms
- HPD fixes
- Support for limiting DP link rate via DT property, this enables
support for HBR3 rates.
DSI:
- Validate display modes according to the DSI OPP table
- DSI PHY support for the SM6375 platform
- Fixed byte intf clock selection for 14nm PHYs
MDP5:
- Schema conversion to YAML
Misc fixes as usual
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
DPU, DSI, MDSS:
- Support for SM8350, SM8450 SM8550 and SC8280XP platform
Core:
- Added bindings for SM8150 (driver support already present)
DPU:
- Partial support for DSC on SM8150 and SM8250
- Fixed color transformation matrix being lost on suspend/resume
DP:
- Support for DP on SDM845 and SC8280XP platforms
- HPD fixes
- Support for limiting DP link rate via DT property, this enables
support for HBR3 rates.
DSI:
- Validate display modes according to the DSI OPP table
- DSI PHY support for the SM6375 platform
- Fixed byte intf clock selection for 14nm PHYs
MDP5:
- Schema conversion to YAML
Misc fixes as usual
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
When converting from .txt to .yaml we didn't include descriptions for the
existing regulator supplies.
- vdd
- vdda
- vddio
Add those descriptions into the yaml now as they were prior to the
conversion. In the .txt description we marked these regulators as required,
however, that requirement appears to have been in error.
Taking the example of sc7180-trogdor-wormdingler.dtsi. The avdd and avee
come from GPIO controlled external regulators, not the SoC and in this case
there's no need for vddio to power an I/O bus. Similarly the regulators for
the LCD are controlled by the panel driver not by the dsi-ctrl driver.
It would be possible to connect a different type of panel to the DSI bus
here in which case we may or may not want to make use of vdd, vdda or
vddio.
This is also the case for older chipsets like apq8064, msm8916 etc the vdd*
regulators in the dsi-ctrl block are helpers not dependencies.
Add the description of vdd, vdda and vddio back in for the existing
upstream dts where vdd, vdda or vddio are already declared but, don't
declare those regulators required - they are not SoC requirements.
Fixes: 4dbe55c977 ("dt-bindings: msm: dsi: add yaml schemas for DSI bindings")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/518643/
Link: https://lore.kernel.org/r/20230116225217.1056258-4-bryan.odonoghue@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
On some SoCs (hello SM6375) vdds-supply is not wired to any smd-rpm
or rpmh regulator, but instead powered by the VDD_MX/mx.lvl line,
which is voted for in the DSI ctrl node.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/518513/
Link: https://lore.kernel.org/r/20230116115132.348961-1-konrad.dybcio@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add binding for the AUO A030JTN01 panel, which is a 320x480 3.0" 4:3
24-bit TFT LCD panel with non-square pixels and a delta-RGB 8-bit
interface.
Signed-off-by: Christophe Branchereau <cbranchereau@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230121162419.284523-2-cbranchereau@gmail.com
Add qcom,sc8280xp-edp to the list of eDP devices, unblocking `aux-bus'
property and fobidding `#sound-dai-cells' property. Also since
sc8280xp-edp, overriding sc8280xp-dp, will contain 5 reg resources, drop
the reg contraint (as it will become equivalent to the top-level one,
requiring min 4 and max 5 reg entries).
Fixes: b6f8c4debc ("dt-bindings: msm/dp: Add SDM845 and SC8280XP compatibles")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/518797/
Link: https://lore.kernel.org/r/20230118031718.1714861-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Extend the Renesas DU display bindings to support the r8a779g0 V4H.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Convert the mdp5.txt into the yaml format. Changes to the existing (txt) schema:
- MSM8996 has additional "iommu" clock, define it separately
- Add new properties used on some of platforms:
- interconnects, interconnect-names
- iommus
- power-domains
- operating-points-v2, opp-table
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/518815/
Link: https://lore.kernel.org/r/20230118041243.1720520-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Backmerging into drm-misc-next to get DRM accelerator infrastructure,
which is required by ipuv driver.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Document RZ/V2L DSI bindings. RZ/V2L MIPI DSI is identical to one found on
the RZ/G2L SoC. No driver changes are required as generic compatible
string "renesas,rzg2l-mipi-dsi" will be used as a fallback.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221122195413.1882486-1-biju.das.jz@bp.renesas.com
Add compatible to support dsi bridge on j721e
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230103101951.10963-3-r-ravikumar@ti.com
Convert cdns,dsi.txt binding to yaml format
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230103101951.10963-2-r-ravikumar@ti.com
UAPI Changes:
* fourcc: Document Open Source user waiver
Cross-subsystem Changes:
* firmware: fix color-format selection for system framebuffers
Core Changes:
* format-helper: Add conversion from XRGB8888 to various sysfb formats;
Make XRGB8888 the only driver-emulated legacy format
* fb-helper: Avoid blank consoles from selecting an incorrect color format
* probe-helper: Enable/disable HPD on connectors plus driver updates
* Use drm_dbg_ helpers in several places
* docs: Document defaults for CRTC backgrounds; Document use of drm_minor
Driver Changes:
* arm/hdlcd: Use new debugfs helpers
* gud: Use new debugfs helpers
* panel: Support Visionox VTDR6130 AMOLED DSI; Support Himax HX8394; Convert
many drivers to common generic DSI write-sequence helper
* v3d: Do not opencode drm_gem_object_lookup()
* vc4: Various HVS an CRTC fixes
* vkms: Fix SEGFAULT from incorrect GEM-buffer mapping
* Convert various drivers to i2c probe_new()
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAmPAA0AACgkQaA3BHVML
eiMKNAgAoXCFd7YMKoHSDlmAOztP+0qdZWM1LkpyC3fTpYbbNC1xI8yn7TVZIbgY
qtkceCUAGmzuO5kTo0aSZdgPWvdWCuDmYBQsX/VwACchSA0aOKZcCaqXGi2Y39D6
G4xsHJyRhU/lWzn/GZQ4+l46m6NAlnrLFBfuLlOHDhYtYZq9D8gXEDm7NSl8/HGF
OjtfSFINKKtOCjvi5GAa8CfnE8GVp59paFKJuj8xU6Dqqlorff+XroWkQG8LV4qi
3UyShQL6d/2hiRQ7fIhXEGCKit7rJkEpfsLvSqJkTkzOKyjhnIZbJIuesgqhtbEH
OpWsmUVKNphi0Y5zw5ZiTqrSy0Py7g==
=+mHi
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2023-01-12' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.3:
UAPI Changes:
* fourcc: Document Open Source user waiver
Cross-subsystem Changes:
* firmware: fix color-format selection for system framebuffers
Core Changes:
* format-helper: Add conversion from XRGB8888 to various sysfb formats;
Make XRGB8888 the only driver-emulated legacy format
* fb-helper: Avoid blank consoles from selecting an incorrect color format
* probe-helper: Enable/disable HPD on connectors plus driver updates
* Use drm_dbg_ helpers in several places
* docs: Document defaults for CRTC backgrounds; Document use of drm_minor
Driver Changes:
* arm/hdlcd: Use new debugfs helpers
* gud: Use new debugfs helpers
* panel: Support Visionox VTDR6130 AMOLED DSI; Support Himax HX8394; Convert
many drivers to common generic DSI write-sequence helper
* v3d: Do not opencode drm_gem_object_lookup()
* vc4: Various HVS an CRTC fixes
* vkms: Fix SEGFAULT from incorrect GEM-buffer mapping
* Convert various drivers to i2c probe_new()
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/Y8ADeSzZDj+tpibF@linux-uq9g
msm-fixes for v6.3-rc4
Display Fixes:
- Fix the documentation for dpu_encoder_phys_wb_init() and
dpu_encoder_phys_wb_setup_fb() APIs to address doc warnings
- Remove vcca-supply and vdds-supply as mandatory for 14nm PHY and
10nm PHY DT schemas respectively as they are not present on some
SOCs using these PHYs
- Add the dsi-phy-regulator-ldo-mode to dsi-phy-28nm.yaml as it was
missed out during txt to yaml migration
- Remove operating-points-v2 and power-domain as a required property
for the DSI controller as thats not the case for every SOC
- Fix the description from display escape clock to display core
clock in the dsi controller yaml
- Fix the memory leak for mdp1-mem path for the cases when we return
early after failing to get mdp0-mem ICC paths for msm
- Fix error handling path in msm_hdmi_dev_probe() to release the phy
ref count when devm_pm_runtime_enable() fails
- Fix the dp_aux_isr() routine to make sure it doesnt incorrectly
signal the aux transaction as complete if the ISR was not an AUX
isr. This fixes a big hitter stability bug on chromebooks.
- Add protection against null pointer dereference when there is no
kms object as in the case of headless adreno GPU in the shutdown
path.
GPU Fixes:
- a5xx: fix quirks to actually be a bitmask and not overwrite each
other
- a6xx: fix gx halt sequence to avoid 1000ms hang on some devices
- kexec shutdown fix
- fix potential double free
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGv7=in_MHW3kdkhqh7ZFoVCmnikmr29YYHCXR=7aOEneg@mail.gmail.com
Require only properties declared in given schema, which makes the code a
bit more readable and easy to follow.
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/514229/
Link: https://lore.kernel.org/r/20221207012231.112059-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add device tree bindings for panels based on the Himax HX8394 controller,
such as the HannStar HSD060BHW4 720x1440 TFT LCD panel that is connected
through a MIPI-DSI video interface.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230102230733.3506624-2-javierm@redhat.com
Require only properties declared in given schema, which makes the code a
bit more readable and easy to follow.
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/514231/
Link: https://lore.kernel.org/r/20221207012231.112059-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
To increase the flexibility of supporting different DP main link configuration
at different platform, add both data-lanes and link-frequencies property
into endpoint so that different platform can specify its own main link
combination of both data lanes and max supported link rate.
Changes in v7:
-- split yaml out of dtsi patch
-- link-frequencies from link rate to symbol rate
-- deprecation of old data-lanes property
Changes in v8:
-- correct Bjorn mail address to kernel.org
Changes in v10:
-- add menu item to data-lanes and link-frequecnis
Changes in v11:
-- add endpoint property at port@1
Changes in v12:
-- use enum for item at data-lanes and link-frequencies
Changes in v13:
-- revised changes at port@0
-- use correct ref schemas for both port@0 and port@1
-- mark both port@0 and port@1 are required
-- add line between data-lanes and link-frequencies properties
Changes in v14:
-- add "unevaluatedProperties: false: to endpoint at port@1
-- remove unnecessary quote to $ref
-- re store "$ref: /schemas/graph.yaml#/properties/port" to port@0
Changes in v15:
-- re store desciption of port@0
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/516094/
Link: https://lore.kernel.org/r/1672163103-31254-3-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
SM8350 and SM8450 platforms use the same driver and same bindings as the
existing 7nm DSI PHYs. Add corresponding compatibility strings.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/514228/
Link: https://lore.kernel.org/r/20221207012231.112059-4-dmitry.baryshkov@linaro.org
[DB: changed compatibles per Krzysztof's request]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
There's a typo in describing the core clock as an 'escape' clock. The
accurate description is 'core'.
Fixes: 4dbe55c977 ("dt-bindings: msm: dsi: add yaml schemas for DSI bindings")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/515938/
Link: https://lore.kernel.org/r/20221223021025.1646636-4-bryan.odonoghue@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
power-domain is required for the sc7180 dispcc GDSC but not every qcom SoC
has a similar dependency for example the apq8064.
Most Qcom SoC's using mdss-dsi-ctrl seem to have the ability to
power-collapse the MDP without collapsing DSI.
For example the qcom vendor kernel commit for apq8084, msm8226, msm8916,
msm8974.
7b5c011a77
"ARM: dts: msm: add mdss gdsc supply to dsi controller device
It is possible for the DSI controller to be active when MDP is
power collapsed. DSI controller needs to have it's own vote for
mdss gdsc to ensure that gdsc remains on in such cases."
This however doesn't appear to be the case for the apq8064 so we shouldn't
be marking power-domain as required in yaml checks.
Fixes: 4dbe55c977 ("dt-bindings: msm: dsi: add yaml schemas for DSI bindings")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/515958/
Link: https://lore.kernel.org/r/20221223021025.1646636-3-bryan.odonoghue@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
UAPI Changes:
* connector: Support analog-TV mode property
* media: Add MEDIA_BUS_FMT_RGB565_1X24_CPADHI,
MEDIA_BUS_FMT_RGB666_1X18 and MEDIA_BUS_FMT_RGB666_1X24_CPADHI
Cross-subsystem Changes:
* dma-buf: Documentation fixes
* i2c: Introduce i2c_client_get_device_id() helper
Core Changes:
* Improve support for analog TV output
* bridge: Remove unused drm_bridge_chain functions
* debugfs: Add per-device helpers and convert various DRM drivers
* dp-mst: Various fixes
* fbdev emulation: Always pick 32 bpp as default
* KUnit: Add tests for managed helpers; Various cleanups
* panel-orientation: Add quirks for Lenovo Yoga Tab 3 X90F and DynaBook K50
* TTM: Open-code ttm_bo_wait() and remove the helper
Driver Changes:
* Fix preferred depth and bpp values throughout DRM drivers
* Remove #CONFIG_PM guards throughout DRM drivers
* ast: Various fixes
* bridge: Implement i2c's probe_new in various drivers; Fixes; ite-it6505:
Locking fixes, Cache EDID data; ite-it66121: Support IT6610 chip,
Cleanups; lontium-tl9611: Fix HDMI on DragonBoard 845c; parade-ps8640:
Use atomic bridge functions
* gud: Convert to DRM shadow-plane helpers; Perform flushing synchronously
during atomic update
* ili9486: Support 16-bit pixel data
* imx: Split off IPUv3 driver; Various fixes
* mipi-dbi: Convert to DRM shadow-plane helpers plus rsp driver changes;i
Support separate I/O-voltage supply
* mxsfb: Depend on ARCH_MXS or ARCH_MXC
* omapdrm: Various fixes
* panel: Use ktime_get_boottime() to measure power-down delay in various
drivers; Fix auto-suspend delay in various drivers; orisetech-ota5601a:
Add support
* sprd: Cleanups
* sun4i: Convert to new TV-mode property
* tidss: Various fixes
* v3d: Various fixes
* vc4: Convert to new TV-mode property; Support Kunit tests; Cleanups;
dpi: Support RGB565 and RGB666 formats; dsi: Convert DSI driver to
bridge
* virtio: Improve tracing
* vkms: Support small cursors in IGT tests; Various fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAmO0B0QACgkQaA3BHVML
eiMKtAf9EXt5yaEonR4gsGNVD70VkebW+jPEWbEMg5hMFDHE9sjBja8T7bOxeeL1
BVofJiAuEZW9176eqeWvShuwOuiE7lf4WQLMvXfFmtHF/Nac9HUtEvOcvc1vEDUB
y6VFlVHe8mSp+Iy0WPLyZCtT4d7v2eM+VYm0HgFa74dSTzQTLGPiUI/XVb/YDaA7
FHKB5NvsMX9S1XvjxCsq0jA5bo8SSzh5CVKerdAZkBJMCSmKiY09o2p5C7vw3EAz
WUXL5CXqd9bwgvZa/9ZClQtpJaikNGoOaMSEl67rbWdVTk0LIpqx3nTY15py5LXd
SG4Wtfor3Vf1REa9TrR2uCIOmh+1gQ==
=0/PC
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2023-01-03' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.3:
UAPI Changes:
* connector: Support analog-TV mode property
* media: Add MEDIA_BUS_FMT_RGB565_1X24_CPADHI,
MEDIA_BUS_FMT_RGB666_1X18 and MEDIA_BUS_FMT_RGB666_1X24_CPADHI
Cross-subsystem Changes:
* dma-buf: Documentation fixes
* i2c: Introduce i2c_client_get_device_id() helper
Core Changes:
* Improve support for analog TV output
* bridge: Remove unused drm_bridge_chain functions
* debugfs: Add per-device helpers and convert various DRM drivers
* dp-mst: Various fixes
* fbdev emulation: Always pick 32 bpp as default
* KUnit: Add tests for managed helpers; Various cleanups
* panel-orientation: Add quirks for Lenovo Yoga Tab 3 X90F and DynaBook K50
* TTM: Open-code ttm_bo_wait() and remove the helper
Driver Changes:
* Fix preferred depth and bpp values throughout DRM drivers
* Remove #CONFIG_PM guards throughout DRM drivers
* ast: Various fixes
* bridge: Implement i2c's probe_new in various drivers; Fixes; ite-it6505:
Locking fixes, Cache EDID data; ite-it66121: Support IT6610 chip,
Cleanups; lontium-tl9611: Fix HDMI on DragonBoard 845c; parade-ps8640:
Use atomic bridge functions
* gud: Convert to DRM shadow-plane helpers; Perform flushing synchronously
during atomic update
* ili9486: Support 16-bit pixel data
* imx: Split off IPUv3 driver; Various fixes
* mipi-dbi: Convert to DRM shadow-plane helpers plus rsp driver changes;i
Support separate I/O-voltage supply
* mxsfb: Depend on ARCH_MXS or ARCH_MXC
* omapdrm: Various fixes
* panel: Use ktime_get_boottime() to measure power-down delay in various
drivers; Fix auto-suspend delay in various drivers; orisetech-ota5601a:
Add support
* sprd: Cleanups
* sun4i: Convert to new TV-mode property
* tidss: Various fixes
* v3d: Various fixes
* vc4: Convert to new TV-mode property; Support Kunit tests; Cleanups;
dpi: Support RGB565 and RGB666 formats; dsi: Convert DSI driver to
bridge
* virtio: Improve tracing
* vkms: Support small cursors in IGT tests; Various fixes
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/Y7QIwlfElAYWxRcR@linux-uq9g
Add bindings for the Forcaltech gpt3, which is a 640x480 3.0" 4:3
IPS LCD Panel found in the YLM/Anbernic RG300X handheld.
Signed-off-by: Christophe Branchereau <cbranchereau@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221219195233.375637-3-cbranchereau@gmail.com
On some SoCs (hello SM6350) vdds-supply is not wired to any smd-rpm
or rpmh regulator, but instead powered by the VDD_MX/mx.lvl line,
which is voted for in the DSI ctrl node.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Fixes: 8fc939e72f ("dt-bindings: msm: dsi: add yaml schemas for DSI PHY bindings")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/511889/
Link: https://lore.kernel.org/r/20221116163218.42449-1-konrad.dybcio@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
On some SoCs (hello SM6115) vcca-supply is not wired to any smd-rpm
or rpmh regulator, but instead powered by the VDD_MX line, which is
voted for in the DSI ctrl node.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 8fc939e72f ("dt-bindings: msm: dsi: add yaml schemas for DSI PHY bindings")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/513555/
Link: https://lore.kernel.org/r/20221130135807.45028-1-konrad.dybcio@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
modify VDOSYS0 display device tree Documentations for MT8188.
Signed-off-by: Nathan Lu <nathan.lu@mediatek.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20221206020046.11333-2-nathan.lu@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The Devicetree bindings document does not have to say in the title that
it is a "Devicetree binding", but instead just describe the hardware.
Drop beginning "Devicetree bindings" in various forms:
find Documentation/devicetree/bindings/ -type f -name '*.yaml' \
-exec sed -i -e 's/^title: [dD]evice[ -]\?[tT]ree [bB]indings\? for \([tT]he \)\?\(.*\)$/title: \u\2/' {} \;
find Documentation/devicetree/bindings/ -type f -name '*.yaml' \
-exec sed -i -e 's/^title: [bB]indings\? for \([tT]he \)\?\(.*\)$/title: \u\2/' {} \;
find Documentation/devicetree/bindings/ -type f -name '*.yaml' \
-exec sed -i -e 's/^title: [dD][tT] [bB]indings\? for \([tT]he \)\?\(.*\)$/title: \u\2/' {} \;
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # MMC
Acked-by: Stephen Boyd <sboyd@kernel.org> # clk
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> # input
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sre@kernel.org> # power
Link: https://lore.kernel.org/r/20221216163815.522628-8-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
The Devicetree bindings document does not have to say in the title that
it is a "binding", but instead just describe the hardware.
Drop trailing "bindings" in various forms (also with trailing full
stop):
find Documentation/devicetree/bindings/ -type f -name '*.yaml' \
-not -name 'trivial-devices.yaml' \
-exec sed -i -e 's/^title: \(.*\) [bB]indings\?\.\?$/title: \1/' {} \;
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Matti Vaittinen <mazziesaccount@gmail.com> # ROHM
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # MMC
Acked-by: Stephen Boyd <sboyd@kernel.org> # clk
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> # input
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # media
Acked-by: Sebastian Reichel <sre@kernel.org> # power
Acked-by: Viresh Kumar <viresh.kumar@linaro.org> # cpufreq
Link: https://lore.kernel.org/r/20221216163815.522628-7-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
The Devicetree bindings document does not have to say in the title that
it is a "Devicetree binding", but instead just describe the hardware.
Drop trailing "Devicetree bindings" in various forms (also with
trailing full stop):
find Documentation/devicetree/bindings/ -type f -name '*.yaml' \
-not -name 'trivial-devices.yaml' \
-exec sed -i -e 's/^title: \(.*\) [dD]evice[ -]\?[tT]ree [bB]indings\?\.\?$/title: \1/' {} \;
find Documentation/devicetree/bindings/ -type f -name '*.yaml' \
-not -name 'trivial-devices.yaml' \
-exec sed -i -e 's/^title: \(.*\) [dD]evice[ -]\?[nN]ode [bB]indings\?\.\?$/title: \1/' {} \;
find Documentation/devicetree/bindings/ -type f -name '*.yaml' \
-not -name 'trivial-devices.yaml' \
-exec sed -i -e 's/^title: \(.*\) [dD][tT] [bB]indings\?\.\?$/title: \1/' {} \;
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # IIO
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # MMC
Acked-by: Stephen Boyd <sboyd@kernel.org> # clk
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> # input
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # media
Acked-by: Sebastian Reichel <sre@kernel.org> # power
Link: https://lore.kernel.org/r/20221216163815.522628-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
The power-domains property is mandatory on i.MX8M Mini, Nano, Plus
and i.MX6SX, i.MX6SL. Document the property and mark it as required
on the aforementioned variants of the IP, present in those SoCs.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20221213132006.6446-1-marex@denx.de
Signed-off-by: Rob Herring <robh@kernel.org>
Currently there are no "upstream" users. So, no existing users to break.
Add properties to restrict dp output data-lanes and clock.
Signed-off-by: Pin-Yen Lin <treapking@chromium.org>
Signed-off-by: allen Chen <allen.chen@ite.com.tw>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221103091243.96036-2-allen.chen@ite.com.tw
Add documentation for the new io-supply property, which specifies the
regulator for the I/O voltage supply on platforms where the panel
panel power and I/O supplies are separate.
Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221201160245.2093816-4-otto.pflueger@abscue.de
DT Bindings:
- Various LED binding conversions and clean-ups. Convert the ir-spi-led,
pwm-ir-tx, and gpio-ir-tx LED bindings to schemas. Consistently
reference LED common.yaml or multi-led schemas and disallow undefined
properties.
- Convert IDT 89HPESx, pwm-clock, st,stmipid02, Xilinx PCIe hosts,
and fsl,imx-fb bindings to schema
- Add ata-generic, Broadcom u-boot environment, and dynamic MTD
sub-partitions bindings.
- Make all SPI based displays reference spi-peripheral-props.yaml
- Fix some schema property regex's which should be fixed strings or were
missing start/end anchors
- Remove 'status' in examples, again...
DT Core:
- Fix a possible NULL dereference in overlay functions
- Fix kexec reading 32-bit "linux,initrd-{start,end}" values (which
never worked)
- Add of_address_count() helper to count number of 'reg' entries
- Support .dtso extension for DT overlay source files. Rename staging
and unittest overlay files.
- Update dtc to upstream v1.6.1-63-g55778a03df61
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEktVUI4SxYhzZyEuo+vtdtY28YcMFAmOWhJAACgkQ+vtdtY28
YcMrAhAAjXJMmhzh97MPN/hUnVy26xVj0IF+pX7AIlHieOZWtc1xFNSqXVblC/n3
459Id1jKq1Vt8BTX0J4VWIOY/v3qpuGtvT4KpronOr0GV/fGhHkBJa/PTBN2/xvS
yG27PLL/F5l3adZ8vhmJdcoxDknqL0oSpWpgwRNHveIB+FzjP7z0LveV+vfS0bEO
nQbM07TMeXzRN+Ld76aEEorsv4uaOrpzBwX76X+F2uAmzsA+3ksLzhULS4551Qxs
63lCgZ6nIdYVIjsqxNFfFEuBNarYCi4KJw7NZksoM0YSXeijWtWazUxbeEa28+SV
dB2OaWzwPt5hS3cJhZ9oM+YK2LNlhXOl+e9MK9ZuGnMzEf9JXj4wJhYkxhA5KrB5
KVXQciYkDm+SbZk9e0AcoV5OqVIvfHfDxTN4ysNe/BHMwMPyyifNvCdx3faiWLVZ
sMrxb44l3JMrQD70XMSdFYFkuw1KfWXuXRWSvFmixiXkSPQWoQMnuVXYEZfNRqth
PdPXgqh2KQ7zrjLSZrrKNqBLzHR94UkUuAu8rsDmapWj7KKP48tLoeooMgLvMAJz
xp7KowVKTim1OSywVWW7UH6gkFagCqI/v9uCxvCTjKutjv9Hzeyask8Z/N/IGhIp
wG+c1jhFAXhPnbMV7k7QJnPPrpVPM1ZFKVklc6ZaqxumXcCAik0=
=y/xu
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DT Bindings:
- Various LED binding conversions and clean-ups. Convert the
ir-spi-led, pwm-ir-tx, and gpio-ir-tx LED bindings to schemas.
Consistently reference LED common.yaml or multi-led schemas and
disallow undefined properties.
- Convert IDT 89HPESx, pwm-clock, st,stmipid02, Xilinx PCIe hosts,
and fsl,imx-fb bindings to schema
- Add ata-generic, Broadcom u-boot environment, and dynamic MTD
sub-partitions bindings.
- Make all SPI based displays reference spi-peripheral-props.yaml
- Fix some schema property regex's which should be fixed strings or
were missing start/end anchors
- Remove 'status' in examples, again...
DT Core:
- Fix a possible NULL dereference in overlay functions
- Fix kexec reading 32-bit "linux,initrd-{start,end}" values (which
never worked)
- Add of_address_count() helper to count number of 'reg' entries
- Support .dtso extension for DT overlay source files. Rename staging
and unittest overlay files.
- Update dtc to upstream v1.6.1-63-g55778a03df61"
* tag 'devicetree-for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (42 commits)
dt-bindings: leds: Add missing references to common LED schema
dt-bindings: leds: intel,lgm: Add missing 'led-gpios' property
of: overlay: fix null pointer dereferencing in find_dup_cset_node_entry() and find_dup_cset_prop()
dt-bindings: lcdif: Fix constraints for imx8mp
media: dt-bindings: atmel,isc: Drop unneeded unevaluatedProperties
dt-bindings: Drop Jee Heng Sia
dt-bindings: thermal: cooling-devices: Add missing cache related properties
dt-bindings: leds: irled: ir-spi-led: convert to DT schema
dt-bindings: leds: irled: pwm-ir-tx: convert to DT schema
dt-bindings: leds: irled: gpio-ir-tx: convert to DT schema
dt-bindings: leds: mt6360: rework to match multi-led
dt-bindings: leds: lp55xx: rework to match multi-led
dt-bindings: leds: lp55xx: switch to preferred 'gpios' suffix
dt-bindings: leds: lp55xx: allow label
dt-bindings: leds: use unevaluatedProperties for common.yaml
dt-bindings: thermal: tsens: Add SM6115 compatible
of/kexec: Fix reading 32-bit "linux,initrd-{start,end}" values
dt-bindings: display: Convert fsl,imx-fb.txt to dt-schema
dt-bindings: Add missing start and/or end of line regex anchors
dt-bindings: qcom,pdc: Add missing compatibles
...
Initial accel subsystem support. There are no drivers yet, just the framework.
New driver:
- ofdrm - replacement for offb
fbdev:
- add support for nomodeset
fourcc:
- add Vivante tiled modifier
core:
- atomic-helpers: CRTC primary plane test fixes, fb access hooks
- connector: TV API consistency, cmdline parser improvements
- send connector hotplug on cleanup
- sort makefile objects
tests:
- sort kunit tests
- improve DP-MST tests
- add kunit helpers to create a device
sched:
- module param for scheduling policy
- refcounting fix
buddy:
- add back random seed log
ttm:
- convert ttm_resource to size_t
- optimize pool allocations
edid:
- HFVSDB parsing support fixes
- logging/debug improvements
- DSC quirks
dma-buf:
- Add unlocked vmap and attachment mapping
- move drivers to common locking convention
- locking improvements
firmware:
- new API for rPI firmware and vc4
xilinx:
- zynqmp: displayport bridge support
- dpsub fix
bridge:
- adv7533: Remove dynamic lane switching
- it6505: Runtime PM support, sync improvements
- ps8640: Handle AUX defer messages
- tc358775: Drop soft-reset over I2C
panel:
- panel-edp: Add INX N116BGE-EA2 C2 and C4 support.
- Jadard JD9365DA-H3
- NewVision NV3051D
amdgpu:
- DCN support on ARM
- DCN 2.1 secure display
- Sienna Cichlid mode2 reset fixes
- new GC 11.x firmware versions
- drop AMD specific DSC workarounds in favour of drm code
- clang warning fixes
- scheduler rework
- SR-IOV fixes
- GPUVM locking fixes
- fix memory leak in CS IOCTL error path
- flexible array updates
- enable new GC/PSP/SMU/NBIO IP
- GFX preemption support for gfx9
amdkfd:
- cache size fixes
- userptr fixes
- enable cooperative launch on gfx 10.3
- enable GC 11.0.4 KFD support
radeon:
- replace kmap with kmap_local_page
- ACPI ref count fix
- HDA audio notifier support
i915:
- DG2 enabled by default
- MTL enablement work
- hotplug refactoring
- VBT improvements
- Display and watermark refactoring
- ADL-P workaround
- temp disable runtime_pm for discrete-
- fix for A380 as a secondary GPU
- Wa_18017747507 for DG2
- CS timestamp support fixes for gen5 and earlier
- never purge busy TTM objects
- use i915_sg_dma_sizes for all backends
- demote GuC kernel contexts to normal priority
- gvt: refactor for new MDEV interface
- enable DC power states on eDP ports
- fix gen 2/3 workarounds
nouveau:
- fix page fault handling
- Ampere acceleration support
- driver stability improvements
- nva3 backlight support
msm:
- MSM_INFO_GET_FLAGS support
- DPU: XR30 and P010 image formats
- Qualcomm SM6115 support
- DSI PHY support for QCM2290
- HDMI: refactored dev init path
- remove exclusive-fence hack
- fix speed-bin detection
- enable clamp to idle on 7c3
- improved hangcheck detection
vmwgfx:
- fb and cursor refactoring
- convert to generic hashtable
- cursor improvements
etnaviv:
- hw workarounds
- softpin MMU fixes
ast:
- atomic gamma LUT support
- convert to SHMEM
lcdif:
- support YUV planes
- Increase DMA burst size
- FIFO threshold tuning
meson:
- fix return type of cvbs mode_valid
mgag200:
- fix PLL setup on some revisions
sun4i:
- A100 and D1 support
udl:
- modesetting improvements
- hot unplug support
vc4:
- support PAL-M
- fix regression preventing 4K @ 60Hz
- fix NULL ptr deref
v3d:
- switch to drm managed resources
renesas:
- RZ/G2L DSI support
- DU Kconfig cleanup
mediatek:
- fixup dpi and hdmi
- MT8188 dpi support
- MT8195 AFBC support
tegra:
- NVDEC hardware on Tegra234 SoC
hdlcd:
- switch to drm managed resources
ingenic:
- fix registration error path
hisilicon:
- convert to drm_mode_init
maildp:
- use managed resources
mtk:
- use drm_mode_init
rockchip:
- use drm_mode_copy
-----BEGIN PGP SIGNATURE-----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=pABG
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2022-12-13' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"The biggest highlight is that the accel subsystem framework is merged.
Hopefully for 6.3 we will be able to line up a driver to use it.
In drivers land, i915 enables DG2 support by default now, and nouveau
has a big stability refactoring and initial ampere support, AMD
includes new hw IP support and should build on ARM again. There is
also an ofdrm driver to take over offb on platforms it's used.
Stuff outside my tree, the dma-buf patches hit a few places, the vc4
firmware changes also do, and i915 has some interactions with MEI for
discrete GPUs. I think all of those should have been acked/reviewed by
relevant parties.
New driver:
- ofdrm - replacement for offb
fbdev:
- add support for nomodeset
fourcc:
- add Vivante tiled modifier
core:
- atomic-helpers: CRTC primary plane test fixes, fb access hooks
- connector: TV API consistency, cmdline parser improvements
- send connector hotplug on cleanup
- sort makefile objects
tests:
- sort kunit tests
- improve DP-MST tests
- add kunit helpers to create a device
sched:
- module param for scheduling policy
- refcounting fix
buddy:
- add back random seed log
ttm:
- convert ttm_resource to size_t
- optimize pool allocations
edid:
- HFVSDB parsing support fixes
- logging/debug improvements
- DSC quirks
dma-buf:
- Add unlocked vmap and attachment mapping
- move drivers to common locking convention
- locking improvements
firmware:
- new API for rPI firmware and vc4
xilinx:
- zynqmp: displayport bridge support
- dpsub fix
bridge:
- adv7533: Remove dynamic lane switching
- it6505: Runtime PM support, sync improvements
- ps8640: Handle AUX defer messages
- tc358775: Drop soft-reset over I2C
panel:
- panel-edp: Add INX N116BGE-EA2 C2 and C4 support.
- Jadard JD9365DA-H3
- NewVision NV3051D
amdgpu:
- DCN support on ARM
- DCN 2.1 secure display
- Sienna Cichlid mode2 reset fixes
- new GC 11.x firmware versions
- drop AMD specific DSC workarounds in favour of drm code
- clang warning fixes
- scheduler rework
- SR-IOV fixes
- GPUVM locking fixes
- fix memory leak in CS IOCTL error path
- flexible array updates
- enable new GC/PSP/SMU/NBIO IP
- GFX preemption support for gfx9
amdkfd:
- cache size fixes
- userptr fixes
- enable cooperative launch on gfx 10.3
- enable GC 11.0.4 KFD support
radeon:
- replace kmap with kmap_local_page
- ACPI ref count fix
- HDA audio notifier support
i915:
- DG2 enabled by default
- MTL enablement work
- hotplug refactoring
- VBT improvements
- Display and watermark refactoring
- ADL-P workaround
- temp disable runtime_pm for discrete-
- fix for A380 as a secondary GPU
- Wa_18017747507 for DG2
- CS timestamp support fixes for gen5 and earlier
- never purge busy TTM objects
- use i915_sg_dma_sizes for all backends
- demote GuC kernel contexts to normal priority
- gvt: refactor for new MDEV interface
- enable DC power states on eDP ports
- fix gen 2/3 workarounds
nouveau:
- fix page fault handling
- Ampere acceleration support
- driver stability improvements
- nva3 backlight support
msm:
- MSM_INFO_GET_FLAGS support
- DPU: XR30 and P010 image formats
- Qualcomm SM6115 support
- DSI PHY support for QCM2290
- HDMI: refactored dev init path
- remove exclusive-fence hack
- fix speed-bin detection
- enable clamp to idle on 7c3
- improved hangcheck detection
vmwgfx:
- fb and cursor refactoring
- convert to generic hashtable
- cursor improvements
etnaviv:
- hw workarounds
- softpin MMU fixes
ast:
- atomic gamma LUT support
- convert to SHMEM
lcdif:
- support YUV planes
- Increase DMA burst size
- FIFO threshold tuning
meson:
- fix return type of cvbs mode_valid
mgag200:
- fix PLL setup on some revisions
sun4i:
- A100 and D1 support
udl:
- modesetting improvements
- hot unplug support
vc4:
- support PAL-M
- fix regression preventing 4K @ 60Hz
- fix NULL ptr deref
v3d:
- switch to drm managed resources
renesas:
- RZ/G2L DSI support
- DU Kconfig cleanup
mediatek:
- fixup dpi and hdmi
- MT8188 dpi support
- MT8195 AFBC support
tegra:
- NVDEC hardware on Tegra234 SoC
hdlcd:
- switch to drm managed resources
ingenic:
- fix registration error path
hisilicon:
- convert to drm_mode_init
maildp:
- use managed resources
mtk:
- use drm_mode_init
rockchip:
- use drm_mode_copy"
* tag 'drm-next-2022-12-13' of git://anongit.freedesktop.org/drm/drm: (1397 commits)
drm/amdgpu: fix mmhub register base coding error
drm/amdgpu: add tmz support for GC IP v11.0.4
drm/amdgpu: enable GFX Clock Gating control for GC IP v11.0.4
drm/amdgpu: enable GFX Power Gating for GC IP v11.0.4
drm/amdgpu: enable GFX IP v11.0.4 CG support
drm/amdgpu: Make amdgpu_ring_mux functions as static
drm/amdgpu: generally allow over-commit during BO allocation
drm/amd/display: fix array index out of bound error in DCN32 DML
drm/amd/display: 3.2.215
drm/amd/display: set optimized required for comp buf changes
drm/amd/display: Add debug option to skip PSR CRTC disable
drm/amd/display: correct DML calc error of UrgentLatency
drm/amd/display: correct static_screen_event_mask
drm/amd/display: Ensure commit_streams returns the DC return code
drm/amd/display: read invalid ddc pin status cause engine busy
drm/amd/display: Bypass DET swath fill check for max clocks
drm/amd/display: Disable uclk pstate for subvp pipes
drm/amd/display: Fix DCN2.1 default DSC clocks
drm/amd/display: Enable dp_hdmi21_pcon support
drm/amd/display: prevent seamless boot on displays that don't have the preferred dig
...
i.MX8MP uses 3 clocks, so soften the restrictions for clocks & clock-names.
This SoC requires a power-domain for this peripheral to use. Add it as
a required property.
Fixes: f5419cb074 ("dt-bindings: lcdif: Add compatible for i.MX8MP")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20221208140840.3227035-1-alexander.stein@ew.tq-group.com
Signed-off-by: Rob Herring <robh@kernel.org>
Compared to the txt description this adds clocks and clock-names to
match reality.
Note that fsl,imx-lcdc was picked as the new name as this is the actual
hardware's name. There will be a new binding implementing the saner drm
concept that is supposed to supersede this legacy fb binding
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221129180414.2729091-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Rob Herring <robh@kernel.org>
Rename name-prefix.yaml into common DAI schema and document
'#sound-dai-cells' for completeness. The '#sound-dai-cells' cannot be
really constrained, as there are users with value of 0, 1 and 2, but at
least it brings definition to one common place.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221203160442.69594-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add DPU and MDSS schemas to describe MDSS and DPU blocks on the Qualcomm
SM6115 platform.
Configuration for DSI/PHY is shared with QCM2290 so compatibles are reused.
Lack of dsi phy supply in example is intended
due to fact on qcm2290, sm6115 and sm6125
this phy is supplied via power domain, not regulator.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/512872/
Link: https://lore.kernel.org/r/20221124001708.25720-2-a39.skl@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
1. Fixup of dpi and hdmi
2. Move panel connector to head
3. Add MT8188 dpi support
4. Add MT8195 AFBC support
-----BEGIN PGP SIGNATURE-----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=6ACI
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-6.2' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 6.2
1. Fixup of dpi and hdmi
2. Move panel connector to head
3. Add MT8188 dpi support
4. Add MT8195 AFBC support
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221123234855.2485-1-chunkuang.hu@kernel.org
Adding in msm8939 which is based msm8916 dtsi I stumbled across a binding
check complaining about the phy name for msm8916 which we were reusing for
msm8939.
The currently inconsistent upstream dtsi naming of "dsi" and "dsi-phy" is
not captured in the yaml for this driver.
The driver however doesn't care about the name of DSI phy, hence the yaml
check is redundant.
Both Krzysztof and Rob suggested we could drop the phy-names entirely if it
really isn't a dependency.
So, drop the inconsistent and unnecessary phy-names field from the yaml.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
UAPI Changes:
Cross-subsystem Changes:
- fbdev: Add support for the nomodeset kernel parameter
Core Changes:
- client: Add kunit tests for drm_connector_pick_cmdline_mode()
- dma-buf: Move dma_buf_mmap_internal() to new locking specification
- edid: Dump EDID on drm_edid_get_panel_id() failure, Stop using a
temporary device to load the EDID through the firmware mechanism
- fb-helper: Remove damage worker
- gem-vram: Fix deadlock in drm_gem_vram_vmap()
- modes: Named mode parsing improvements
- tests: Add Kunit helpers to create a DRM device
Driver Changes:
- hisilicon: convert to drm_mode_init()
- malidp: Use drm-managed resources
- msm: convert to drm_mode_init() and drm_mode_copy()
- mtk: convert to drm_mode_init()
- nouveau: Support backlight control for nva3
- rockchip: convert to drm_mode_copy()
- sti: convert to drm_mode_copy()
- v3d: Switch to drm-managed resources
- vc4: Fix potential NULL pointer dereference
- panels:
- New panel: NewVision NV3051D
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCY3XyTAAKCRDj7w1vZxhR
xfh8APkBLspfEk0WneXqIanPLOLCIU4Fcd7IvjNsy5nRODM5ewD8D4pCzRYz6zGf
0rAHzuvISUBHBWES/EWpO61GJ7d/1gA=
=ZM1O
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2022-11-17' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 6.2:
UAPI Changes:
Cross-subsystem Changes:
- fbdev: Add support for the nomodeset kernel parameter
Core Changes:
- client: Add kunit tests for drm_connector_pick_cmdline_mode()
- dma-buf: Move dma_buf_mmap_internal() to new locking specification
- edid: Dump EDID on drm_edid_get_panel_id() failure, Stop using a
temporary device to load the EDID through the firmware mechanism
- fb-helper: Remove damage worker
- gem-vram: Fix deadlock in drm_gem_vram_vmap()
- modes: Named mode parsing improvements
- tests: Add Kunit helpers to create a DRM device
Driver Changes:
- hisilicon: convert to drm_mode_init()
- malidp: Use drm-managed resources
- msm: convert to drm_mode_init() and drm_mode_copy()
- mtk: convert to drm_mode_init()
- nouveau: Support backlight control for nva3
- rockchip: convert to drm_mode_copy()
- sti: convert to drm_mode_copy()
- v3d: Switch to drm-managed resources
- vc4: Fix potential NULL pointer dereference
- panels:
- New panel: NewVision NV3051D
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20221117083628.mzij5nrbdzokek7c@houat
Add documentation for the NewVision NV3051D panel bindings.
Note that for the two expected consumers of this panel binding
the underlying LCD model is unknown. Name "anbernic,rg353p-panel"
is used because the hardware itself is known as "anbernic,rg353p".
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221111203130.9615-3-macroalpha82@gmail.com
The RZ/G2L MIPI DSI TX is embedded in the Renesas RZ/G2L family SoC's. It
can operate in DSI mode, with up to four data lanes.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The "40nm" MIPI DSI controller found in the A100 and D1 SoCs has the
same register layout as previous SoC integrations. However, its module
clock now comes from the TCON, which means it no longer runs at a fixed
rate, so this needs to be distinguished in the driver.
The controller also now uses pins on Port D instead of dedicated pins,
so it drops the separate power domain.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20221107053552.2330-3-samuel@sholland.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The A64 case should have limited maxItems, instead of duplicating the
minItems value from the main binding. While here, simplify the binding
by making this an "else" case of the two-clock conditional block.
Fixes: fe5040f284 ("dt-bindings: sun6i-dsi: Document A64 MIPI-DSI controller")
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20221107053552.2330-2-samuel@sholland.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
