Instead of listing directly properties typical for SPI peripherals,
reference the spi-peripheral-props.yaml schema. This allows using all
properties typical for SPI-connected devices, even these which device
bindings author did not tried yet.
Remove the spi-* properties which now come via spi-peripheral-props.yaml
schema, except for the cases when device schema adds some constraints
like maximum frequency.
While changing additionalProperties->unevaluatedProperties, put it in
typical place, just before example DTS.
The sitronix,st7735r references also panel-common.yaml and lists
explicitly allowed properties, thus here reference only
spi-peripheral-props.yaml for purpose of documenting the SPI slave
device and bringing spi-max-frequency type validation.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220727164312.385836-1-krzysztof.kozlowski@linaro.org
The datasheet lists the minimum Serial clock cycle (Write) as 66ns which is
15MHz. Mostly it can do much better than that and is in fact often run at
32MHz. With a clever driver that runs configuration commands at a low speed
and only the pixel data at the maximum speed the configuration can't be
messed up by transfer errors and the speed is only limited by the amount of
pixel glitches that one is able to tolerate.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211124150757.17929-4-noralf@tronnes.org
The backlight property was lost during conversion to yaml in commit
abdd9e3705 ("dt-bindings: display: sitronix,st7735r: Convert to DT schema").
Put it back.
Fixes: abdd9e3705 ("dt-bindings: display: sitronix,st7735r: Convert to DT schema")
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211124150757.17929-2-noralf@tronnes.org
David Lechner noticed (paraphrased):
- not all properties from panel-common are applicable.
- missing optional rotation and backlight properties
Fix this by listing all allowed properties,
and do not allow other properties.
Fixes: abdd9e3705 ("dt-bindings: display: sitronix,st7735r: Convert to DT schema")
Reported-by: David Lechner <david@lechnology.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Cc: David Lechner <david@lechnology.com>
Cc: dri-devel@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20200120190249.GA9619@ravnborg.org
Document support for the Okaya RH128128T display, which is a 128x128
1.44" TFT display driven by a Sitronix ST7715R TFT Controller/Driver.
It can be found on e.g. the Renesas YRSK-LCD-PMOD extension board, which
comes with various Renesas development kits (e.g. Renesas Starter Kit+
for RZ/A1H[1]).
ST7715R and ST7735R are very similar. Their major difference is that
the former is restricted to displays of up to 132x132 pixels, while the
latter supports displays up to 132x162 pixels.
[1] https://renesasrulz.com/the_vault/f/archive-forum/4981/upgrading-to-the-renesas-rz-a1h
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200115124548.3951-3-geert+renesas@glider.be
Convert the DT binding documentation for Sitronix ST7735R displays to DT
schema.
Add a reference to the Adafruit 1.8" LCD while at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200115124548.3951-2-geert+renesas@glider.be
